Bingo Drift Trike

DRIFT TRIKE

OWNER’S MANUAL

Main Parts of Drift Trike

No. Description

1 Plastics set 2 Brake cable

3 Brake lever

4 Seat

5 Motor 12V 100W

6 Controller 12V 100W

7 Charger 12V

8 Push throttle

9 Battery 4.5A

10 Grips

11 Drum brake

12 Sprocket

13 Chain

14 Front wheel

15 Rear wheel ( with light) with plastic cover set

16 Flag set

OWNER’S MANUAL

SAFETY WARNIN

WARNING: Riding an electric drift trike can be a hazardous bike can and is intended to move, and it is therefore possible to activity. Certain conditions may cause the equipment to fail lose control, fall off and/or get into dangerous situations that no without fault of the manufacturer. Like other electric products, the amount of care, instruction or expertise can eliminate. If such things occur you can be seriously injured or die, even when high-stress activity. using safety equipment and other precautions. RIDE AT YOUR OWN RISK AND USE COMMON SENCE. Be careful and know your limitations, Risk of injury increases as the degree of riding difficulty increases. The rider assumes all APPROPRIATE RIDER USE AND PARENTAL SUPERVISION risk associated with aggressive riding activity. The recommended rider age of 8 years is only an estimate, and can be affected by the rider’s size, weight or skills. Any rider Maintain a hold on the handlebars at all times unable to fie comfortably on the bike should not attempt to rider Never carry passengers or allow more than one person at a time it. to ride the electric drift trike. A parent’s decision to allow his or her child to ride this product should be based on the child’s maturity, skill and Never use near steps or swimming pools. ability to follow rules. Keep your fingers and other body parts away from the drive Keep this product away from small children and remember that chain, steering system, wheels and all other moving this product is intended for use only by persons who are, at components. minimum, completely comfortable and competent while operating the product. Never use headphones or a cell phone when riding. Never hitch a ride with another product. DO NOT EXCEED THE WEIGHT LIMIT OF 50 KGS. Rider weight does not necessarily mean a person’s size is appropriate Do not ride the product in wet or icy weather and never immerse to fit or maintain control of the product. the electric drift trike in water, as the electrical and drive components could be damaged by water or create other Do not touch the brakes or electric motor on your electric drift possible unsafe conditions. trike when in use and/or immediately after riding as they can become very hot. Wet, slick, bumpy, uneven or rough surfaces may increase risks of use. Do not ride the electric drift trike in mud, ice, puddles or ACCEPTABLE RIDING PRACTICES AND CONDITONS water. Avoid excessive speeds that can be associated with down Always check and obey any local laws or regulations which hill rides. Never risk damaging surfaces such as carpet or may affect the locations where the product may be used. flooring by use of an electric four wheeler indoors. Ride defensively. Watch out for potential obstacles that could Do not ride at night or when visibility is limited. catch your wheel or force you to swerve suddenly or lose control. Be careful to avoid pedestrians, skaters, skateboards, PROPER RIDING ATTIRE scooters, bikes, children or animals who may enter your path, Always wear proper protective equipment such as an approved and respect the rights and property of others. safety helmet (with chin strap securely buckled), elbow pads and kneepads. A helmet may be legally required by local law or The product is meant to be used on private property and on regulation in your area. A long-sleeved shirt, long pants and closed courses and not on public streets or sidewalks. Do not gloves are recommended. Always wear athletic shoes (lace-up ride your electric drift trike in any areas where pedestrian or shoes with rubber soles), never ride barefooted or in sandals, vehicle traffic is present. and keep shoelaces tied and out of the way of the wheels, motor and drive system. Do not activate the speed control on the hand grip unless you are on the electric drift trike and in a case, outdoor environment USING THE CHARGER suitable for riding. The charger supplied with the electric drift tike should be regularly examined for damaged to the cord, plug, enclosure and This product was manufactured for performance and durability other parts, and in the event of such damage, the four wheeler but is not impervious to damage. Jumping or other aggressive mush not be charged until the charger has been repaired or riding can over-stress and damage any product, including the replaced. electric drift trike, and the rider assumes all risks associated with Use only with the recommended charger. Always disconnect from the charger prior to wiping down and Use caution when charging. cleaning your bike with liquid.

The charger is not a toy. Charger should be operated by an FAILURE TO USE COMMON SENSE AND HEED THE ABOVE adult. WARNNINGS INCREASES RISK OF SERIOUS INJURY. USE WITH APPROPRIATE CAUTION AND SERIOUS ATTENTION Do not operate charger near flammable materials. TO SAFE OPERATION. 2． Unplug charger and disconnect from bike when not in use. MODEL AND TECHNICAL SPECIFICATIONS 3

Model DRIFT TRIKE

Engine 100W Electric Motor

Motor Max Loaded Amps 4.5 A

Controller Type Air Cooled, Non Water Proof, Brake Shut-off, Charger Port

Battery Lead-Acid, 12V/4.5AH x 1 pc

Charging Time 3-5 hours Initial charge time: 12 hours

Max Speed 10 km/h ( depending terrain surface )

Max Distance Ride 3-5 km ( depending on rider weight & road condition )

Front Brake Front drum brake

Maximum Load 50 kg

Front & Rear Wheel Front： 200X50 Rear: Caster Wheels

Control System PUSH BUTTON Throttle Rider Capacity 1 person (recommend age is 8 and above)

Dimensions (L x W x H) BIKE: 95*60*60 (cm) BOX : 77*58*22 (cm) Seat Height : 16 cm

Weight Gross: 16 kg Net: 13 kg

ASSEMBLY AND SET-UP

Attaching the Frame Insert the rear frame into the frame assembly. Securely tighten the bolts on the rear frame and in the middle of the frame.

Attaching the Front Fork Insert the front fork into the frame assembly. Be sure to properly align the slot on headtube with the pin on the front fork. Insert the steering bolt and secure.

Attaching the Seat Align the four holes in seat with the four holes in frame. Tighten the coupling bolts.

Inflating the Tires Tire is inflated when shipped, but it invariably loses some pressure between the point of manufacturing and your purchase. Inflate the tire to the correct PSI indicated on the side-wall of the tire before first time use.

Testing the Brake To use the brake, squeeze the lever (pedal) to increase the pressure on the brake. The brake lever is fitted with a cable adjuster to compensate for cable stretch and/or to fine-tune the lever movement to break engagement.

BEFORE RIDING

Charging the Battery Your electric four wheeler may not have a fully charged battery; therefore it is a good idea to charge the battery prior to use.

● Initial charge time: 12 hours ● Run time: Up to 40 minutes of continuous ride time. ●Recharge time: 3-5 hours Run time may vary depending on riding conditions, Depending on level of depletion Climate and/or proper maintenance. ● Fully charge battery before storing ●Average battery life: 250 charge/ discharge cycles ●When the bike is not in regular use, ●To ensure long battery life, do not store the battery recharge the battery at least once a In temperatures above 60°or below -10°C. month until normal use is resumed. 7 Note: Make sure power is turned OFF when unit is not is use. If the power switch is left on for an extended period of time, the battery may reach a stage at which it will no longer hold a charge.

1. Turn power OFF before charging. Plug the charger into the charger port to charge unit.

2. Plug the charger into a wall outlet. If the lights on charger do not light up, check the power to the outlet. If necessary, try a different outlet.

To start the unit, turn the power switch ON. Place both hands on the handlebars and press the push button throttle. NOTE: Keep both feet on the foot pegs when unit is in motion.

To stop the unit, release the push button throttle and apply the brake until the unit comes to a complete stop.

REPAIR AND MAINTENANCE

Make sure the power switch is turned OFF

Adjusting the brake To adjust the brake cable tension, thread the brake lever adjuster in or out 1/4 to 1/2 turn until the desired brake adjustment in attained. If the brake still needs further adjustment, proceed to remove the motor cover/chain guard, loosen the nut on the brake cable for additional adjustment. Securely tighten the nut when finished.

Chain and Sprocket The chain will typically have a “loose spot” and “tight spot” corresponding with a particular sprocket rotational position. This is normal and common to all chain-driven products due to run-out tolerances of the free wheel and sprocket. Proper chain alignment must be maintained. If the chain is noisy or rough running, check the lubrication, tension and alignment of the sprocket, in that order.

Battery Care and Disposal Do not store the battery in temperatures above 60°or below -10°C.

BATTERY CONTAINS SEALED LEAD. BATTERY MUST BE RECYCLED.

Charger The charger supplied with the electric four wheeler should be regularly examined for damage to the cord, plug, enclosure and other parts, and, in the event of such damage, the product must not be charged until it has been repaired or replaced.

Use ONLY with the recommended charger.

8 TROUBLESHOOTING GUIDE

Problem Possible Cause Solution

Product does not run Undercharged battery Charge the battery, a new battery should have been charged for at least 12 hours before using the product for the first time and up to 12 hours after each subsequent use.

Check all connectors. Make sure the charger connector is tightly plugged into the charging port, and the charger is plugged into the wall.

Product suddenly Loose wire or connectors Check all wires and connectors to make sure they are tight Stopped working while In use Motor or electrical switch damage Contact your local dealer for diagnosis and repair.

Short run time (less than undercharged battery Charge the battery, A new battery should have been charged for at 15 minutes per charge) least 12 hours before using the product for the first time and up to 12 hours after each subsequent use.

Check all connectors. Make sure the charger connector is tightly plugged into the charging port, and the charger is plugged into the wall.

Brakes are not adjusted properly Adjust the brake

Product runs sluggishly Riding conditions are too stressful Use only on solid, flat clean and dry surfaces such as pavement or level ground

Tires are not properly inflated The tires are inflated when shipped, but they invariably lose some pressure between the point of manufacturing and your purchase. Inflate the tires to the correct PSI indicated on the side-wall of the tire before first time use.

Product is over load Make sure you do not overload the product by allowing more than one rider at one time, exceeding the maximum weight limit, going up too steep a hill or towing objects behind the product.

Sometimes the product loose wires or connectors Check all wires around the motors and all connectors to make sure Doesn’t, but other times they are right. It does Motor or electrical switch damage Contact your local dealer for diagnosis and repair.

Product makes loud Chain is too dry Apply a lubricant to the chain. Noise or grinding Sounds 9