Section 224213.16 - Commercial Urinals s1

Exclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA

This Product MasterSpec Section is licensed by ARCOM to Zurn Industries, LLC ("Licensee").

This Product MasterSpec Section modifies the original MasterSpec text, and does not include the full content of the original MasterSpec Section.

Revisions made to the original MasterSpec text are made solely by the Licensee and are not endorsed by, or representative of the opinions of, ARCOM or The American Institute of Architects (AIA). Neither AIA nor ARCOM are liable in any way for such revisions or for the use of this Product MasterSpec Section by any end user. A qualified design professional should review and edit the document to suit project requirements.

For more information, contact Zurn Industries, LLC, 1801 Pittsburg Ave., Erie, PA 16502; Phone: (855) ONE ZURN; Fax: (814) 875-1402; Website: www.zurn.com; Email: [email protected].

For information about MasterSpec contact ARCOM at (800) 424-5080 or visit www.MasterSpec.com.

SECTION 224213.16 - COMMERCIAL URINALS

Revise this Section by deleting and inserting text to meet Project-specific requirements.

Verify that Section titles referenced in this Section are correct for this Project's Specifications; Section titles may have changed.

PART 1 - GENERAL

0.1 RELATED DOCUMENTS

Retain or delete this article in all Sections of Project Manual.

A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.

0.2 SUMMARY

A. Section Includes:

1. Urinals. 2. Flushometer valves.

B. Related Requirements:

Retain subparagraph below to cross-reference requirements Contractor might expect to find in this Section but are specified in other Sections.

1. Section 224600 "Security Plumbing Fixtures" for security urinals.

0.3 ACTION SUBMITTALS

A. Product Data: For each type of product.

1. Include construction details, material descriptions, dimensions of individual components and profiles, and finishes for urinals. 2. Include rated capacities, operating characteristics, electrical characteristics, and furnished specialties and accessories.

B. LEED Submittals:

Retain "Product Data for Prerequisite WE 1 ( and Credit WE 3) (, Credit WE 2, and Credit WE 3)" Subparagraph below for LEED-NC, LEED-CS, and LEED for Schools for fixtures and equipment that consume water.

1. Product Data for Prerequisite WE 1[ and Credit WE 3] [, Credit WE 2, and Credit WE 3]: Documentation indicating flow and water consumption requirements.

Retain "Product Data for Prerequisite WE 1" Subparagraph below for LEED-CI for fixtures and equipment that consume water. 2. Product Data for Prerequisite WE 1: Documentation indicating flow and water consumption requirements.

Retain "Product Data for Prerequisite WE 1( and Credit WE 2)" Subparagraph below for LEED-EB for fixtures and equipment that consume water. 3. Product Data for Prerequisite WE 1[ and Credit WE 2]: Documentation indicating flow and water consumption requirements.

Retain "Shop Drawings" Paragraph below if equipment includes wiring.

C. Shop Drawings: Include diagrams for power, signal, and control wiring.

0.4 CLOSEOUT SUBMITTALS

A. Operation and Maintenance Data: For flushometer valves[ and electronic sensors] to include in operation and maintenance manuals.

PART 2 - PRODUCTS

See Editing Instruction No. 1 in the Evaluations for cautions about named manufacturers and products. For an explanation of options and Contractor's product selection procedures, see Section 016000 "Product Requirements."

Do not use same urinal designation as is used for another urinal in Section 224600 "Security Plumbing Fixtures."

0.1 STALL URINALS

Copy "Urinals" Paragraph below and re-edit for each type of stall, wash-out-type urinal required.

Insert number to complete drawing designation. Use these designations on Drawings to identify each urinal.

A. Urinals : Stall, washout type.

1. Basis-of-Design Product: Subject to compliance with requirements, provide Zurn Industries, LLC; Commercial Brass and Fixtures; or comparable product by one of the following:

a. American Standard. b. Kohler Co. c. .

Caution: This type of urinal requires a drainage piping trap under the urinal. This trap is not part of the urinal fittings.

2. Fixture:

a. Standards: ASME A112.19.2/CSA B45.1 and ASME A112.19.5. b. Material: Vitreous china. c. Type: [Straight or sloped] front.

Retain "Seam Covers" Subparagraph below if two or more stall urinals will be installed side by side. d. Seam Covers: For [21-inch (535-mm)] [24-inch (610-mm)] urinal centers. e. Strainer: Separate; removable. f. Water Consumption: Water saving. g. Spud Size and Location: NPS 3/4 (DN 20); top. h. Outlet Size and Location: NPS 2 (DN 50); bottom for separate trap. i. Color: [White] .

Add "-WS1" to model numbers in options below to designate flush volume of 1.0 gal (3.8 L) per flush. Add "-EWS" to designate 0.5 gal (1.9 L) per flush. Flush Valve Selection: Z6003AV is manual diaphragm; Z6203 is manual piston; ZTR6203 is battery powered solenoid sensor; ZER6003AV-CPM is battery powered diaphragm; ZEMS6003AV is hardwired diaphragm in wall sensor; ZTR6203-LL is 10 year battery powered piston operated, solenoid activated flush valve; and ZEMS6003AV-IS is hardwired diaphragm side mounted sensor.

3. Flushometer Valve: [Z6003AV] [Z6203] [ZTR6203] [ZER6003AV-CPM] [ZTR6203- LL] [ZEMS6003AV] [ZEMS6003AV-IS].

0.2 WALL-HUNG URINALS

Copy "Urinals" Paragraph below and re-edit for each type of wall-hung, back-outlet, blowout urinal required.

Insert number to complete drawing designation. Use these designations on Drawings to identify each urinal.

A. Urinals : Wall hung, back outlet, blowout.

Retain "Manufacturers" Subparagraph and list of manufacturers below to require products from manufacturers listed or a comparable product from other manufacturers.

1. Manufacturers: Subject to compliance with requirements, [provide products by the following] [provide products by one of the following] [available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following]:

Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific product or a comparable product from manufacturers listed. Retain option and delete insert note if manufacturer's name and model number are indicated on Drawings. 2. Basis-of-Design Product: Subject to compliance with requirements, provide [product indicated on Drawings] or comparable product by one of the following:

a. American Standard. b. Kohler Co. c. .

3. Fixture:

a. Standards: ASME A112.19.2/CSA B45.1 and ASME A112.19.5. b. Material: Vitreous china.

Second option in "Strainer or Trapway" Subparagraph below may not be available from some manufacturers. Extended shields vary in shape and dimensions. Verify availability and suitability if required. c. Strainer or Trapway: [Manufacturer's standard strainer] [Open trapway] with integral trap. d. Water Consumption: Water saving.

First option in "Spud Size and Location" Subparagraph below is available from some manufacturers. Back spud is used with a remote hard-wired, solenoid-actuator, electronic-sensor flushometer valve. Verify availability if required. e. Spud Size and Location: NPS 1-1/4 (DN 32); [back] [top]. f. Outlet Size and Location: NPS 2 (DN 50); back. g. Color: [White] .

Add "-WS1" to model numbers in options below to designate flush volume of 1.0 gal (3.8 L) per flush. Add "-EWS" to designate 0.5 gal (1.9 L) per flush.

Flush Valve Selection: Z6003AV is manual diaphragm; Z6203 is manual piston; ZTR6203 is battery powered solenoid sensor; ZER6003AV-CPM is battery powered diaphragm; ZEMS6003AV is hardwired

COMMERCIAL URINALS 224213.16 - 4 Copyright 2010 AIA MasterSpec Premium 03/10 PRODUCT MASTERSPEC LICENSED BY ARCOM TO ZURN INDUSTRIES, LLC. diaphragm in wall sensor; ZTR6203-LL is 10 year battery powered piston operated, solenoid activated flush valve; and ZEMS6003AV-IS is hardwired diaphragm side mounted sensor.

4. Flushometer Valve: [Z6003AV] [Z6203] [ZTR6203] [ZER6003AV-CPM] [ZTR6203- LL] [ZEMS6003AV] [ZEM6003AV-IS]. 5. Waste Fitting:

a. Standard: ASME A112.18.2/CSA B125.2 for coupling. b. Size: NPS 2 (DN 50).

6. Support: ASME A112.6.1M, Type I, urinal carrier with fixture support plates and coupling with seal and fixture bolts and hardware matching fixture.[ Include rectangular, steel uprights.]

a. Basis-of-Design Product: Subject to compliance with requirements, provide Zurn Plumbing Products Group; [Z1221 - Plate Type Systems wall urinal] [Z1222 - Plate Type system with bearing plate] or comparable product by one of the following:

1) .

Copy "Urinals" Paragraph below and re-edit for each type of wall-hung, back-outlet, siphon-jet urinal required.

Insert number to complete drawing designation. Use these designations on Drawings to identify each urinal.

B. Urinals : Wall hung, back outlet, siphon jet[, accessible].

1. Basis-of-Design Product: Subject to compliance with requirements, provide Zurn Industries LLC; Commercial Brass and Fixtures; Z5730 or comparable product by one of the following:

a. American Standard. b. Kohler Co. c. .

2. Fixture:

a. Standards: ASME A112.19.2/CSA B45.1 and ASME A112.19.5. b. Material: Vitreous china.

Option in "Type" Subparagraph below may not be available from some manufacturers. Extended shields vary in shape and dimensions. Verify availability and suitability if required. c. Type: Siphon jet[ with extended shields]. d. Strainer or Trapway: [Manufacturer's standard strainer] with integral trap.

e. Water Consumption: 1.0 gal (3.8 L) per flush.

First option in "Spud Size and Location" Subparagraph below is available from some manufacturers. Back spud is used with a remote hard-wired, solenoid-actuator, electronic-sensor flushometer valve. Verify availability if required. f. Spud Size and Location: NPS 3/4 (DN 20); [back] [top]. g. Outlet Size and Location: NPS 2 (DN 50); back. h. Color: [White] .

Add "-WS1" to model numbers in options below to designate flush volume of 1.0 gal (3.8 L) per flush.

Flush Valve Selection: Z6003AV is manual diaphragm; ZTR6203 is battery powered solenoid sensor; ZER6003AV-CPM is battery powered diaphragm; ZEMS6003AV is hardwired diaphragm in wall sensor; ZTR6203-LL is 10 year battery powered piston operated, solenoid activated flush valve; and ZEMS6003AV-IS is hardwired diaphragm side mounted sensor.

3. Flushometer Valve: [Z6003AV] [ZTR6203] [ZER6003AV-CPM] [ZTR6203-LL] [ZEMS6003AV] [ZEMS6003AV-IS]. 4. Waste Fitting:

a. Standard: ASME A112.18.2/CSA B125.2 for coupling. b. Size: NPS 2 (DN 50).

5. Support: ASME A112.6.1M, Type I, urinal carrier with fixture support plates and coupling with seal and fixture bolts and hardware matching fixture.[Include rectangular, steel uprights.]

1) .

Copy "Urinals" Paragraph below and re-edit for each type of wall-hung, back-outlet, washout urinal required.

Insert number to complete drawing designation. Use these designations on Drawings to identify each urinal.

C. Urinals : Wall hung, back outlet, washout[, accessible].

First option in "Basis-of-Design" subparagraph below is 1.0/0.5 gal (3.8/1.9 L) per flush. Other four options, designated with "-U", are 0.125 gal (0.47 L) per flush.

1. Basis-of-Design Product: Subject to compliance with requirements, provide Zurn Industries, LLC; Commercial Brass and Fixtures; [Z5708-U] [Z5738-U] [Z5755-U] [Z5758-U] [] [Z5765-U] or comparable product by one of the following:

a. American Standard. b. Kohler Co. c. .

2. Fixture:

a. Standards: ASME A112.19.2/CSA B45.1 and ASME A112.19.5. b. Material: Vitreous china. c. Type: Washout with extended shields. d. Strainer or Trapway: [Manufacturer's standard strainer] with integral trap. e. Water Consumption: [0.125 gal (0.47 L) per flush] [0.5 gal (1.9 L) per flush] [1.0 gal (3.8 L) per flush].

First option in "Spud Size and Location" Subparagraph below is available from some manufacturers. Back spud is used with a remote hard-wired, solenoid-actuator, electronic-sensor flushometer valve. Verify availability if required. f. Spud Size and Location: NPS 3/4 (DN 20), [back] [top]. g. Outlet Size and Location: NPS 2 (DN 50), back. h. Color: [White] .

Add "-WS1" to model numbers in options below to designate flush volume of 1.0 gal (3.8 L) per flush. Add "-EWS" to designate 0.5 gal (1.9 L) per flush and “–ULF” to designate 0.125 gal (0.47 L) per flush.

Flush Valve Selection: Z6003AV is manual diaphragm; Z6203 is manual piston; ZEG6003 is battery powered solenoid sensor; ZTR6203 is battery powered solenoid sensor; ZER6003AV-CPM is battery powered diaphragm; ZEMS6003AV is hardwired diaphragm in wall sensor; ZTR6203-LL is 10 year battery powered piston operated, solenoid activated flush valve; and ZEMS6003AV-IS is hardwired diaphragm side mounted sensor.

3. Flushometer Valve: [Z6003AV] [Z6200] [ZEG6003EV] [ZTR6203] [ZER6003AV- CPM] [ZTR6203-LL] [ZEMS6003AV] [ZEMS6003AV-IS]. 4. Waste Fitting:

a. Standard: ASME A112.18.2/CSA B125.2 for coupling. b. Size: NPS 2 (DN 50).

5. Support: ASME A112.6.1M, Type I, urinal carrier with fixture support plates and coupling with seal and fixture bolts and hardware matching fixture.[Include rectangular, steel uprights.]

1) .

Copy "Urinals" Paragraph below and re-edit for each type of wall-hung, bottom-outlet, washout urinal required.

Insert number to complete drawing designation. Use these designations on Drawings to identify each urinal.

D. Urinals : Wall hung, bottom outlet, washout.

1. Basis-of-Design Product: Subject to compliance with requirements, provide Zurn Industries, LLC; Commercial Brass and Fixtures; Z5720 or comparable product by one of the following:

a. American Standard. b. Kohler Co. c. .

2. Fixture:

a. Standards: ASME A112.19.2/CSA B45.1 and ASME A112.19.5. b. Material: Vitreous china. c. Drain: Separate removable chrome-plated dome strainer with chrome-plated, NPS 1-1/2 (DN 40) tailpiece. d. Strainer or Trapway: Manufacturer's standard strainer and NPS 1-1/2 (DN 40) tailpiece. e. Design Consumption: [Water saving] [Low]. f. Inlet Spud Size and Location: NPS 3/4 (DN 20); top. g. Outlet Size and Location: NPS 1-1/2 (DN 40); bottom. h. Color: [White] .

Add "-WS1" to model numbers in options below to designate flush volume of 1.0 gal (3.8 L) per flush.

Flush Valve Selection: Z6003AV is manual diaphragm; Z6203 is manual piston ZTR6203 is battery powered solenoid sensor; ZER6003AV-CPM is battery powered diaphragm; ZEMS6003AV is hardwired diaphragm in wall sensor; ZTR6203-LL is 10 year battery powered piston operated, solenoid activated flush valve; and ZEMS6003AV-IS is hardwired diaphragm side mounted sensor.

3. Flushometer Valve: [Z6003AV] [Z6203] [ZTR6203] [ZER6003AV-CPM] [ZTR6203- LL] [ZEMS6003AV] [ZEMS6003AV-IS]. 4. Waste Fitting:

a. Standard: ASME A112.18.2/CSA B125.2. b. Trap:

1) Size: NPS 1-1/2 (DN 50).

Retain one of two "Material" subparagraphs below.

2) Material: Chrome-plated, [two-piece, cast-brass trap and swivel elbow with 0.032-inch- (0.83-mm-) thick brass tube to wall] [two-piece, cast- brass trap and ground-joint swivel elbow with 0.032-inch- (0.83-mm-) thick brass tube to wall] [one-piece, cast-brass trap with swivel 0.029- inch- (73-mm-) thick tubular brass wall bend] ; and chrome-plated brass or steel wall flange. 3) Material: Stainless-steel, two-piece trap and swivel elbow with 0.012-inch- (0.30-mm-) thick stainless-steel tube to wall; and stainless-steel wall flange.

5. Support: ASME A112.6.1M, Type II, urinal carrier with hanger and bearing plates. [ Include rectangular, steel uprights.]

1) .

Copy "Urinals" Paragraph below and re-edit for each type of wall-hung, bottom-outlet, wash-down urinal required.

Insert number to complete drawing designation. Use these designations on Drawings to identify each urinal.

E. Urinals : Wall hung, bottom outlet, wash down.

1. Basis-of-Design Product: Subject to compliance with requirements, provide Zurn Industries, LLC; Commercial Brass and Fixtures; Z5720 or comparable product by one of the following:

a. American Standard. b. Kohler Co. c. .

2. Fixture:

a. Standards: ASME A112.19.1/CSA B45.2 and ASME A112.19.5. b. Material: Enameled cast iron. c. Style: Wash sink with back and without pedestal modified for use as urinal. d. Size: [36 inches (915 mm)] [48 inches (1219 mm)] [60 inches (1525 mm)] [72 inches (1830 mm)]. e. Drain: Separate removable chrome-plated dome strainer with chrome-plated, NPS 1-1/2 (DN 40) tailpiece. f. Water Consumption: Not applicable. g. Flushing Device: Manufacturer's standard self-closing valve with washdown pipe of length matching fixture.

h. Outlet Size and Location: NPS 1-1/2 (DN 40); bottom. i. Color: [White] .

Add "-WS1" to model numbers in options below to designate flush volume of 1.0 gal (3.8 L) per flush.

Flush Valve Selection: Z6003AV is manual diaphragm; Z6203 is manual piston; ZTR6203 is battery powered solenoid sensor; ZER6003AV-CPM is battery powered diaphragm; ZEMS6003AV is hardwired diaphragm in wall sensor; ZTR6203-LL is 10 year battery powered piston operated, solenoid activated flush valve; and ZEMS6003AV-IS is hardwired diaphragm side mounted sensor.

3. Flushometer Valve: [Z6003AV] [Z6203] [ZTR6203] [ZER6003AV-CPM] [ZTR6203- LL] [ZEMS6003AV] [ZEMS6003AV-IS].

4. Waste Fitting:

a. Standard: ASME A112.18.2/CSA B125.2. b. Trap:

1) Size: NPS 1-1/2 (DN 50).

Retain one of two "Material" subparagraphs below. 2) Material: Chrome-plated, [two-piece, cast-brass trap and swivel elbow with 0.032-inch- (0.83-mm-) thick brass tube to wall] [two-piece, cast- brass trap and ground-joint swivel elbow with 0.032-inch- (0.83-mm-) thick brass tube to wall] [one-piece, cast-brass trap with swivel 0.029- inch- (73-mm-) thick tubular brass wall bend] ; and chrome-plated brass or steel wall flange. 3) Material: Stainless-steel, two-piece trap and swivel elbow with 0.012-inch- (0.30-mm-) thick stainless-steel tube to wall; and stainless-steel wall flange.

5. Support: ASME A112.6.1M, Type II, sink carrier.

0.3 WATERFREE URINALS

Copy "Urinals" Paragraph below and re-edit for each type of wall-hung, back-outlet, waterless, vitreous- china urinal required.

Insert number to complete drawing designation. Use these designations on Drawings to identify each urinal.

A. Urinals : Wall hung, back outlet, waterless, vitreous china, designed for liquid-trap-seal operation.

1. Basis-of-Design Product: Subject to compliance with requirements, provide Zurn Industries, LLC; Commercial Brass and Fixtures; Z5795 or comparable product by one of the following:

a. Kohler Co. b. Sloan Valve Company. c. .

2. Fixture:

a. Standard: ASME A112.19.2/CSA B45.1, except without water supply. b. Trap-Seal Method: Liquid seal. c. Outlet Size and Location: [NPS 2 (DN 50)] flange; back. d. Trap-Sealing Liquid: Proprietary. e. Color: [White] .

3. Waste Fitting:

a. Standard: ASME A112.18.2/CSA B125.2 for transition coupling, trap, and waste pipe. b. Size: [NPS 2 (DN 50)] .

4. Support: ASME A112.6.1M, Type I, urinal carrier with fixture support plates and coupling with seal and fixture bolts and hardware matching fixture.[ Include rectangular, steel uprights.]

1) .

Copy "Urinals" Paragraph below and re-edit for each type of wall-hung, back-outlet, waterless, plastic urinal required.

Insert number to complete drawing designation. Use these designations on Drawings to identify each urinal.

B. Urinals : Wall hung, back outlet, waterless, plastic, designed for liquid-trap-seal operation.

Retain "Manufacturers" Subparagraph and list of manufacturers below to require products from manufacturers listed or a comparable product from other manufacturers.

2. Basis-of-Design Product: Subject to compliance with requirements, provide [product indicated on Drawings] or comparable product by one of the following:

a. Waterless Co. b. .

3. Fixture:

a. Standard: ANSI Z124.9, except without water supply. b. Material: [FRP] . c. Trap-Seal Method: Proprietary cartridge or trap system. d. Outlet Size and Location: NPS 2 (DN 50); back. Include transition coupling. e. Trap-Sealing Liquid: Proprietary. f. Color: [White] .

4. Waste Fitting:

a. Standard: ASME A112.18.2/CSA B125.2 for transition coupling, trap, and waste pipe. b. Size: [NPS 2 (DN 50)] .

5. Support: [Metal plate in wall] [Wood blocking in wall] [ASME A112.6.1M, Type I, urinal carrier with fixture support plates and coupling with seal and fixture bolts and hardware matching fixture].[ Include rectangular, steel uprights.]

0.4 URINAL FLUSHOMETER VALVES

Caution: Flushometer-valve consumption must match the water consumption of the urinal.

A. Lever-Handle, Diaphragm Flushometer Valves :

1. Basis-of-Design Product: Subject to compliance with requirements, provide Zurn Industries, LLC; Commercial Brass and Fixtures; [Z6003AV-ULF, 0.125 gal (0.47 L) per flush] [Z6003AV-EWS, 0.5 gal (1.9 L) per flush] [Z6003AV-WS1, 1.0 gal (3.8 L) per flush] or comparable product by one of the following:

a. Coyne & Delany Co. b. Sloan Valve Company. c. .

2. Standard: ASSE 1037. 3. Maximum Pressure Rating: 125 psig (860 kPa). 4. Features: Include integral check stop and backflow-prevention device. 5. Material: Brass body with corrosion-resistant components. 6. Exposed Flushometer-Valve Finish: Chrome plated.

Retain "Panel Finish" Subparagraph below for concealed flushometer-valve components. 7. Panel Finish: Chrome plated or stainless steel. 8. Style: [Exposed] [Concealed]. 9. Consumption: [0.125 gal. (0.47 L)] [0.5 gal. (1.9 L)] [1.0 gal. (3.8 L)] per flush. 10. Minimum Inlet: [NPS 3/4 (DN 20)] [NPS 1 (DN 25)]. 11. Minimum Outlet: [NPS 3/4 (DN 20)] [NPS 1-1/4 (DN 32)].

B. Solenoid-Actuator, Diaphragm Flushometer Valves :

1. Basis-of-Design Product: Subject to compliance with requirements, provide Zurn Industries, LLC; Commercial Brass and Fixtures; [ZTR6203-ULF, 0.125 gal (0.47 L) per flush] [ZR6003AV-WS1, 1.0 gal (3.8 L) per flush] or comparable product by one of the following:

a. Coyne & Delany Co. b. Sloan Valve Company. c. .

C. Hydraulic-Actuator, Push-Button, Diaphragm Flushometer Valves :

1. Basis-of-Design Product: Subject to compliance with requirements, provide Zurn Industries, LLC; Commercial Brass and Fixtures; AquaVantage [ZH6002AV-ULF, 0.125 gal (0.47 L) per flush] [ZH6003AV-EWS, 0.5 gal (1.9 L) per flush] [ZH6003AV-WS1, 1.0 gal (3.8 L) per flush] or comparable product by one of the following:

a. Coyne & Delany Co. b. Sloan Valve Company.

c. .

D. Lever-Handle, Piston Flushometer Valves :

1. Basis-of-Design Product: Subject to compliance with requirements, provide Zurm Industries, LLC; Commercial Brass and Fittings; [MetroFlush Z6200-WS1, 1.0 gal (3.8 L) per flush] [MetroFlush Z6200-EWS, 0.5 gal (1.9 L) per flush] or comparable product by one of the following:

a. Coyne & Delany Co. b. Sloan Valve Company. c. .

Retain "Panel Finish" Subparagraph below for concealed flushometer-valve components. 7. Panel Finish: Chrome plated or stainless steel. 8. Style: [Exposed] [Concealed]. 9. Consumption: [0.5 gal. (1.9 L)] [1.0 gal. (3.8 L)] per flush. 10. Minimum Inlet: [NPS 3/4 (DN 20)] [NPS 1 (DN 25)]. 11. Minimum Outlet: [NPS 3/4 (DN 20)] [NPS 1-1/4 (DN 32)].

E. Hard-Wired, Solenoid-Actuator, Piston Flushometer Valves :

1. Basis-of-Design Product: Subject to compliance with requirements, provide Zurn Industries, LLC; Commercial Brass and Fixtures; MetroFlush [ZEMS6203-EWS, 0.5 gal (1.9 L) per flush] [ZEMS6203-WS1, 1.0 gal (3.8 L) per flush] or comparable product by one of the following:

List of manufacturers below is for hard-wired, solenoid-actuator, electronic-sensor, piston flushometer valves. a. Sloan Valve Company. b. .

Retain "Panel Finish" Subparagraph below for concealed flushometer-valve components. 7. Panel Finish: Chrome plated or stainless steel. 8. Style: [Exposed] [Concealed]. 9. Consumption: [0.5 gal. (1.9 L)] [1.0 gal. (3.8 L)] per flush. 10. Minimum Inlet: [NPS 3/4 (DN 20)] [NPS 1 (DN 25)]. 11. Minimum Outlet: [NPS 3/4 (DN 20)] [NPS 1-1/4 (DN 32)].

F. Battery-Powered, Solenoid-Actuator, Piston Flushometer Valves :

1. Basis-of-Design Product: Subject to compliance with requirements, provide Zurn Industries, LLC; Commercial Brass and Fixtures; ZTR Series [ZTR6203-ULF, 0.125 gal (0.5 L) per flush] [ZTR6203-EWS, 0.5 gal (1.9 L) per flush] [ZTR6203-WS1, 1.0 gal (3.8 L) per flush] or comparable product by one of the following:

List of manufacturers below is for battery-powered, solenoid-actuator, electronic-sensor, piston flushometer valves.

a. Coyne & Delany Co. b. Sloan Valve Company. c. .

Retain "Panel Finish" Subparagraph below for concealed flushometer-valve components. 7. Panel Finish: Chrome plated or stainless steel. 8. Style: [Exposed] [Concealed].

9. Consumption: [0.125 gal. (0.5 L)] [0.5 gal. (1.9 L)] [1.0 gal. (3.8 L)] per flush. 10. Minimum Inlet: [NPS 3/4 (DN 20)] [NPS 1 (DN 25)]. 11. Minimum Outlet: [NPS 3/4 (DN 20)] [NPS 1-1/4 (DN 32)].

G. SUPPORT FIXTURES

1. Basis-of-Design Product: Subject to compliance with requirements, provide Zurn Plumbing Products Group; [Z1221 - Plate Type Systems wall urinal] [Z1222 - Plate Type system with bearing plate] or comparable product by one of the following:

a. Josam Company. b. MIFAB, Inc. c. Smith, Jay R. Mfg. Co. d. Tyler Pipe; Wade Div. e. Watts Drainage Products. f. .

PART 3 - EXECUTION

0.1 EXAMINATION

A. Examine roughing-in of water supply and sanitary drainage and vent piping systems to verify actual locations of piping connections before urinal installation.

B. Examine walls and floors for suitable conditions where urinals will be installed.

C. Proceed with installation only after unsatisfactory conditions have been corrected.

0.2 INSTALLATION

A. Urinal Installation:

1. Install urinals level and plumb according to roughing-in drawings. 2. Install wall-hung, back-outlet urinals onto waste fitting seals and attached to supports. 3. Install wall-hung, bottom-outlet urinals with tubular waste piping attached to supports.

Indicate on Drawings those urinals that are required to be accessible. 4. Install accessible, wall-mounted urinals at mounting height for the handicapped/elderly, according to ICC/ANSI A117.1. 5. Install trap-seal liquid in waterless urinals.

B. Support Installation:

1. Install supports, affixed to building substrate, for wall-hung urinals. 2. Use off-floor carriers with waste fitting and seal for back-outlet urinals. 3. Use carriers without waste fitting for urinals with tubular waste piping. 4. Use chair-type carrier supports with rectangular steel uprights for accessible urinals.

C. Flushometer-Valve Installation:

1. Install flushometer-valve water-supply fitting on each supply to each urinal. 2. Attach supply piping to supports or substrate within pipe spaces behind fixtures. 3. Install lever-handle flushometer valves for accessible urinals with handle mounted on open side of compartment. 4. Install fresh batteries in battery-powered, electronic-sensor mechanisms.

D. Wall Flange and Escutcheon Installation:

1. Install wall flanges or escutcheons at piping wall penetrations in exposed, finished locations. 2. Install deep-pattern escutcheons if required to conceal protruding fittings. 3. Comply with escutcheon requirements specified in Section 220518 "Escutcheons for Plumbing Piping."

Retain "Joint Sealing" Paragraph below if sealants are not specified in Section 079200 "Joint Sealants."

E. Joint Sealing:

1. Seal joints between urinals and walls and floors using sanitary-type, one-part, mildew- resistant silicone sealant. 2. Match sealant color to urinal color. 3. Comply with sealant requirements specified in Section 079200 "Joint Sealants."

0.3 CONNECTIONS

Coordinate piping installations and specialty arrangements with Drawings and with requirements specified in piping systems. If Drawings are explicit enough, these requirements may be reduced or omitted.

A. Connect urinals with water supplies and soil, waste, and vent piping. Use size fittings required to match urinals.

B. Comply with water piping requirements specified in Section 221116 "Domestic Water Piping."

C. Comply with soil and waste piping requirements specified in Section 221316 "Sanitary Waste and Vent Piping."

D. Where installing piping adjacent to urinals, allow space for service and maintenance.

0.4 ADJUSTING

A. Operate and adjust urinals and controls. Replace damaged and malfunctioning urinals, fittings, and controls.

B. Adjust water pressure at flushometer valves to produce proper flow.

C. Install fresh batteries in battery-powered, electronic-sensor mechanisms.

0.5 CLEANING AND PROTECTION

A. Clean urinals and fittings with manufacturers' recommended cleaning methods and materials.

B. Install protective covering for installed urinals and fittings.

C. Do not allow use of urinals for temporary facilities unless approved in writing by Owner.

END OF SECTION 224213.16

COMMERCIAL URINALS 224213.16 - 18