1.-Technical Specifications, 200-Gram Card Stock (8-Point)

Annex VI 1.-TECHNICAL SPECIFICATIONS, 200-GRAM CARD STOCK (8-POINT)

STRUCTURAL PROPERTIES SPECIFICATIONS F PROPERTY UNIT TYPE METHOD MIN STD MAX 1 BASIS WEIGHT g / m2 C/A 190 200 210 T-410 Microns 193 204 213 1 THICKNESS C/A T-411 inch/1000 7.6 8.0 8.4

1 ABSOLUTE MOISTURE % C 4 6 8 T-412

OPTICAL PROPERTIES SPECIFICATIONS F PROPERTY UNIT TYPE METHOD MIN STD MAX 1 WHITENESS % C 88 90 --- T-452

1 OPACITY % C 95 97 --- T-425 L* 92 94 --- CIE L*a*b* ISO 11475 1 COLOR a* E 0 0.5 1 b* -7 --- -2.2

COMMERCIAL PROPERTIES SPECIFICATIONS F PROPERTY UNIT TYPE METHOD MIN STD MAX 1 DARK SPOTS ppm C 0 0 15 T-437

LENGTH Direct comparison 1 SIZE TOLERANCE mm C -1 0 1 method WIDTH Direct comparison 1 IMBALANCE TOLERANCE mm C -1 0 1 method

MECHANICAL PROPERTIES SPECIFICATIONS F PROPERTY UNIT TYPE METHOD MIN STD MAX SM 1500 2000 --- 1 STIFFNESS Gurley C T-543 ST 700 1000 ---

DIMENSIONS This specification applies for the formats 54 x74 cm, 58 x 88 cm, 61 x 90 cm and 70 x 95 cm

Notes: 1. The basis weight shall have a tolerance of +/-3% in accordance with the grammage specified by the supplier. 2. Higher caliper poster board will be accepted provided that it complies with the specifications. 3. It must have at least one coated surface. 4. No delamination shall occur in coated and uncoated surfaces. 5. Compliance with these characteristics does not exempt the manufacturer from responsibility for the commercial practices of runnability and printability the poster board must have, nor any hidden damage it may have.

*Test Method: TAPPI Method No. T-410. Grammage of paper and paperboard (weight per unit area) TAPPI Method No. T-411. Thickness (caliper) of paper, paperboard, and combined board. TAPPI Method No. T-412. Moisture in pulp, paper and paperboard TAPPI Method No. T-425. Opacity of paper (15/d geometry, illuminant A/2°, 89% reflectance backing and paper backing) TAPPI Method No. T-452 Brightness of pulp, paper, and paperboard (directional reflectance at 457 nm) TAPPI Method No. T-460. Air resistance of paper (Gurley method)

of 14 Page 2 of 14 TAPPI Method No. T-437 Dirt in paper and paperboard

TAPPI Method No. T-543 Bending resistance of paper (Gurley-type tester)

CIE L*a*b* Method. CIE L*a*b* color space.

ISO 11475 Method. Paper and board -- Determination of CIE whiteness, D65/10 degrees (outdoor daylight)

This technical specification shall be in force from November 14, 2015 to July 30, 2017.

F = FREQUENCY TYPE CODE 1 ANALYSIS OF EVERY BATCH C: CRITICAL PROPERTY 2 ANALYSIS OF EVERY 2 BATCHES E: STATISTICAL PROPERTY 3 ANALYSIS OF EVERY 3 BATCHES T: TYPICAL PROPERTY 4 ANALYSIS OF EVERY 4 BATCHES A: EXEMPTION ON THE BASIS OF QUALITY CERTIFICATE 5 ANALYSIS OF EVERY 5 BATCHES B: EXEMPTION ON THE BASIS OF EXTERNAL CONTROL CERTIFICATE

2.- SAMPLES The bidder shall submit samples of the card stock offered pursuant to section number 5.6.2 of this invitation, to be subject to the tests set forth in point 1 of this Annex, and shall also submit the technical specifications issued by the card stock manufacturer.

of 14 INFORMATIONAL FORM

Annex VII 1.- DELIVERY QUANTITIES, LOCATIONS AND DATES.

Daily delivery of sheets Item Sheets (thousands) Delivery location State Start date of delivery Days for delivery (thousands) Centeno No. 150- 162, Col. 1 1,936 Granjas Esmeralda, C.P. 09810, Mexico City 01/16/2017 200 Monday to Saturday Ciudad de México Av. Hidalgo 111, Sector San 2 621 Nicolás Tolentino, C.P. 09850, Mexico City 01/16/2017 200 Monday to Saturday Iztapalapa, Ciudad de México Calle B # 8, Parque Industrial 3 613 Puebla 01/16/2017 200 Monday to Sunday Puebla 2000, Puebla, Puebla. J.M. Martinez No. 301 Chalco 4 1,255 Estado de México Col. San Estado de México 01/16/2017 200 Monday to Friday Miguel Jacalones C.P. 56600 Alcaicería 8, Paseos De 5 652 Churubusco, Iztapalapa, 09030 Mexico City 01/16/2017 200 Monday to Saturday Ciudad De México Calle E # 6, Parque Industrial 6 1,298 Puebla 01/16/2017 200 Monday to Saturday Puebla 2000, Puebla, Puebla.

Hierro No. 7 Benito Juárez, 7 646 Estado de México 01/16/2017 200 Monday to Saturday Xalostoc, Ecatepec de Morelos Calzada de Viga #1332, 8 1,184 Iztapalapa, C.P. 09430, Ciudad Mexico City 01/16/2017 200 Monday to Saturday de México Durazno No. 1, Esq. Con Ejido, Col. San José de las Peritas, 9 1,879 Mexico City 01/16/2017 200 Monday to Friday Delegación Xochimilco, C.P. 16010, México D.F.

Sheets Daily delivery of sheets Item Delivery location State Start date of delivery Days for delivery (thousands) (thousands)

Av. De las misiones número 6, Parque 10 2,447 Industrial Bernardo Quintana, Municipio El Querétaro 02/27/2017 600 Monday to Friday Marques, Querétaro, C.P 76246

Centeno No. 150- 162, Col. Granjas Esmeralda, 11 1,301 Mexico City 02/27/2017 200 Monday to Saturday C.P. 09810, México, Ciudad de México

Calle B # 8, Parque Industrial Puebla 2000, 12 829 Puebla 02/27/2017 200 Monday to Friday Puebla, Puebla.

of 14 J.M. Martinez No. 301 Chalco Estado de 13 1,602 Estado de México 02/27/2017 200 Monday to Saturday México, Col. San Miguel Jacalones, C.P. 56600

Alcaicería 8, Paseos De Churubusco, Iztapalapa, 14 1,332 Mexico City 02/27/2017 200 Monday to Friday 09030 Ciudad De México, Ciudad de México

Sebastián Lerdo de Tejada No.904, Col. 15 415 Estado de México 02/27/2017 200 Monday to Friday Electricistas Locales, Toluca Edo. de México Calle E # 6, Parque Industrial Puebla 2000, 16 3,169 Puebla 02/27/2017 200 Monday to Sunday Puebla, Puebla. Hierro No. 7 Benito Juárez, Xalostoc, Ecatepec 17 71 Estado de México 02/27/2017 200 Monday to Saturday de Morelos Calzada de Viga #1332, Iztapalapa, C.P. 09430, 18 618 Mexico City 02/27/2017 200 Monday to Saturday Ciudad de México Durazno No. 1, Esq. Con Ejido, Col. San José de 19 1,259 las Peritas, Delegación Xochimilco, C.P. 16010, Mexico City 02/27/2017 200 Monday to Friday México D.F.

of 14 REQUIRED SUBMISSION FORM Annex VIII TECHNICAL ANNEX. MANDATORY COMPLIANCE FORM

LETTER FOR TECHNICAL AND LEGAL OBLIGATIONS

PLACE AND DATE______

NATIONAL COMMISSION OF FREE TEXT BOOKS ATTN: DIRECTOR OF MATERIAL RESOURCES AND GENERAL SERVICES

I refer to the Electronic Open Public International Tender No. LA-011L6J001-E168-2016, in which my principal, the company ______, is participating by means of the proposal contained herein.

Furthermore, my principal declares under oath and under the penalty of perjury for those who declare falsely to the non- judicial authority that:

1) The submitted technical proposal covers items ______of this tender.

2) My principal has the capacity to deliver ____ thousands of sheets as of January 16, 2017 and ____ thousands of sheets as of February 27, 2017. 3) The entirety of the items to be supplied and delivered shall fully and satisfactorily comply with the required specifications of the invitation and its annexes, are free of latent defects and faults, and if awarded, the goods shall comply with the properties listed in the offer. 4) They possess the physical, legal and operational capacity for the infrastructure, equipment, technical personnel specialized in this business activity and the procedures to supply the goods for this tender. 5) The goods shall be delivered with the required quality, timeliness, and efficiency. 6) The goods shall have a one-year warranty, counted from the date of delivery, against manufacturing defects caused by the process itself or the materials used, and against any type of hidden defects. 7) The delivery of the goods covering the submitted technical proposal shall be within the time period set forth in the invitation. 8) The goods shall be delivered free on board to the addresses listed in Annex IX, at the risk and expense of my principal and to the full satisfaction of Conaliteg. 9) If the tender is awarded, the rights and obligations derived from the assigned contract shall not be sub- contracted nor partially or totally transferred, except for collection rights. 10) During this tender and in the case of being awarded, I will maintain strict confidentiality regarding the goods for delivery during the period of the contract on the understanding and accepting that failing to manifest truthfulness will lead to the rescission of the contract executed with Conaliteg. 11)If awarded the tender, goods delivered to Conaliteg that do not meet the technical specifications set forth in this invitation shall be replaced or the necessary modifications shall be made, at no cost for Conaliteg, in a period no greater than two calendar days starting from the date of rejection until the requested technical specifications are fulfilled. 12) They shall assume all liability in the event that, after submitting the offer and its obligations, patents or trademarks are infringed upon or industrial property rights of any type are violated.

of 14 Page 7 of 14 S I N C E R E L Y

Name and signature of the attorney-in-fact or legal representative listed in the legal status form of the bidder or the joint legal representative of the bidders, as set forth in Article 34 of the Public Sector Acquisitions, Leases and Services Act.

of 14 Annex VIII TECHNICAL ANNEX

1. INSTRUCTIONAL DOCUMENT. EXAMPLE INSTRUCTIONAL DOCUMENT DATE. Document No. TO: NAME OF SUPPLIER Legal Representative.

On the basis of contract number XXXXXXXXXX corresponding to the electronic open public international tender LA- 011L6J001-E168-2016, I hereby request the delivery of cardstock as described below:

Unit of Quantity Dimensions Description Order Measurement Thousands

The items above shall be delivered pursuant in the following conditions: Delivery start date: Delivery deadline date: Name of Printer: Address: Hours for receipt: Contact: Telephone:

I hereby reiterate the contractual penalty shall be applied in the event of non-compliance with the delivery of the requested material. That is all for now. Cordial greetings.

SINCERELY ULISES MARTÍNEZ AJA Director of Material Resources and General Services

MANDATORY SUBMISSION FORM Annex IX FINANCIAL PROPOSAL FORM INVITATION FOR THE ELECTRONIC OPEN PUBLIC INTERNATIONAL TENDER NO LA-011L6J001-E168-2016

of 14 Name of bidder: Address: Telephone: Date:

FINANCIAL PROPOSAL Currency used in the financial proposal: (pesos or U.S. dollars).

UNIT PRICE PER ITEM QUANTITY AMOUNT VAT TOTAL AMOUNT THOUSAND 1 1,936 $ $ $ $ 2 621 $ $ $ $ 3 613 $ $ $ $ 4 1,255 $ $ $ $ 5 652 $ $ $ $ 6 1,298 $ $ $ $ 7 646 $ $ $ $ 8 1,184 $ $ $ $ 9 1,879 $ $ $ $ 10 2,447 $ $ $ $ 11 1,301 $ $ $ $ 12 829 $ $ $ $ 13 1,602 $ $ $ $ 14 1,332 $ $ $ $ 15 415 $ $ $ $ 16 3,169 $ $ $ $ 17 71 $ $ $ $ 18 618 $ $ $ $ 19 1,259 $ $ $ $ GRAND TOTAL

1. The prices offered are fixed and final until the complete delivery of the goods, not subject to changes, and the offer is in local currency. 2. This proposal shall be in effect for the entire time period of the contract.

(Name and signature of the attorney-in-fact or legal representative indicated in the legal status form of the bidder) NOTES: 1. Financial proposals that have omitted any of the requirements in this document shall be rejected and the bidder shall be informed of the reasons for the rejection of their proposal. 2. Financial proposals that submit prices with more than two decimal places shall be rejected. 3. This form may be reproduced by the bidder, provided the content is respected, preferably in the order set forth herein.

of 14 OPTIONAL SUBMISSION FORM ANNEX X DECLARATION FOR SUBMISSION BY BIDDERS PARTICIPATING IN INTERNATIONAL CONTRACT PROCEDURES, IN COMPLIANCE WITH THE PROVISIONS OF RULES 5.3 AND 6.3.

______, ______(1) National Commission of Free Textbooks (2) Ulises Martínez Aja Director of Material Resources and General Services

I refer herein to the procedure ___(3)_____ number ___(4)___ in which my principal, the company______(5)______is participating by means of this proposal.

Concerning this matter, and in the terms of the provisions in the “Rules for applying preferential price margins for goods of domestic origin with respect to the price of imported goods, in contracting procedures of an international open character carried out by Federal Public Administrative agencies and entities,” the undersigned declares under oath that in the event that I am awarded the respective contract, the entirety of the goods I offer in said proposal and will supply, under line item __(6)___, shall be produced in the United Mexican States and will have a national content of at least 65%, or ___(7)___% in the case of an exception.

I furthermore declare under oath that I am aware of the provisions set forth in Article 57 of the Public Sector Acquisitions, Leases and Services Act. In this manner, if required I shall accept a compliance check for the requirements regarding the national content of the goods offered herein, by means of displaying the corresponding informational documentation and/or by means of a physical inspection of the industrial plant where the goods are produced, saving said information for three years from the delivery of the goods to the organizer.

SINCERELY

______(8)______

of 14 NUMBER DESCRIPTION 1 Enter the date the document was issued 2 Enter the name of the inviting agency or entity Specify the contractual procedure involved, public tender or invitation to at least three 3 people 4 Enter the corresponding number 5 Enter the name or registered name of the bidding company 6 Enter the corresponding item number Specify the percentage corresponding to Chapter III for cases of exception regarding national content, from the “Rules for the determination, accreditation and verification of the 7 national content of goods offered and delivered in contract procedures, and for the application of national content requirement in public works contracts executed with Federal Public Administrative agencies and entities 8 Enter the name and signature of the representative of the bidding company NOTE* If the bidder is an individual, the pertinent sections of this form may be modified.

of 14 OPTIONAL SUBMISSION FORM ANNEX XI

FORM FOR THE DECLARATION FOR SUBMISSION BY BIDDERS PARTICIPATING IN INTERNATIONAL CONTRACT PROCEDURES, IN COMPLIANCE WITH THE PROVISIONS OF RULE 5.4

______, ______(1) National Commission of Free Textbooks (2) Ulises Martínez Aja Director of Material Resources and General Services

I refer herein to the procedure ___(3)_____ number ___(4)___ in which my principal, the company______(5)______is participating by means of this proposal.

Concerning this matter, and in the terms of the provisions in the “Rules for applying preferential price margins for goods of domestic origin with respect to the price of imported goods, in contracting procedures of an international open character carried out by Federal Public Administrative agencies and entities,” the undersigned declares under oath that in the event that I am awarded the respective contract, the entirety of the goods I offer in said proposal and will supply, under line item __(6)___, originate from ____(7)_____, a country that has signed the Free Trade Agreement _____(8)_____ with the United Mexican States, in accordance with the applicable rules of origin from said agreement in matters of public contracts.

I furthermore declare under oath that in the event of a compliance check of the rules of origin of the goods, I shall provide the information required by the corresponding request and that which supports the veracity thereof at all times, and save said information for three years. SINCERELY ______(9)______

of 14 NUMBER DESCRIPTION 1 Enter the date the document was issued 2 Enter the name of the inviting agency or entity 3 Specify the contractual procedure involved, public tender or invitation to at least three people 4 Enter the corresponding number 5 Enter the name or registered name of the bidding company 6 Enter the corresponding item number 7 Specify the country of origin of the goods 8 Specify the number of the free trade agreement used for the contracting procedure 9 Enter the name and signature of the representative of the bidding company NOTE* If the bidder is an individual, the pertinent sections of this form may be modified.