International Conference on Power Engineering-09

Proceedings of the International Conference on Power Engineering-09 (ICOPE-09) November 16-20, 2009, Kobe, Japan

INTERNATIONAL CONFERENCE ON POWER ENGINEERING-09 INSTRUCTIONS TO AUTHORS FOR TYPING THEIR MANUSCRIPTS (skip 1 line) Hitoshi ASANO*, Yutaka ODA** and Author3** (skip 1 line) *Dept. of Mech. Eng., Kobe University, 1-1, Rokkodai, Nada, Kobe 657-8501, Japan **Affiliation 2, address (skip 2 lines)

ABSTRACT Detailed instructions for typing your article are given in the followings. Since you are requested to send a camera-ready paper, you are personally responsible for the quality and appearance of your work. Please remember the following points in particular: a) type the body of the paper in double column; b) type up to 150 word abstract; c) use 10-pt. Times Roman font or equivalent, and single spaced lines; d) list references in numerical order of appearance; e) paste good quality figures and tables; f) list all the used symbols (together with their units) in a nomenclature section at the end of the paper; g) the use of SI units is mandatory; h) paper length is limited to 6 pages in A4 paper; i) the PDF file named as paper number + corresponding author’s family name should be sent via website or E-mail. Thank you for your patience and cooperation. (skip 1 line) Keywords: Power Engineering, Typing Instruction, Double column, Times Roman, SI Unit, 6 Pages (skip 2 lines)

1. MAILING 10 mm. Leave the top margin of 20 mm, the bottom margin Papers should be prepared according to present of 20 mm. The right and left margins are 15 mm, instructions and converted to a PDF file. Papers are to be respectively. sent via Web site or E-mail the committee members Type the text single-spaced. Times Roman (or an according to countries. The detail information is shown in equivalent typeface) is preferred. A typeface of 10-point (if the last section of this document. The deadline is March 31, using a laser printer) or 12 characters per inch (if using a 2009. typewriter) should be used. Late manuscripts may not be included in the Indent first line of each paragraph five spaces, and do Conference Proceedings. Manuscripts not complying with not leave extra space between paragraphs. present instructions may not appear in the Proceedings. If possible, equalize columns on last page. Authors are strongly requested to attend the Conference and to present their papers in oral sessions 3.3 Paper Heading individually. Pre-registration of at least one of the co- Type the following heading, 10-pt. Arial boldface in authors with registration fee should be made by July upper and lower case letters with a single line spacing, flush 31, 2009. If the pre-registration is not confirmed, the right only on the first page of each paper. manuscript will not be included in the Conference Proceedings. Proceedings of the International Conference on Power Engineering-09 2. PAPER LENGTH AND FILE SIZE (ICOPE-09) November 16-20, 2009, Kobe, Japan Papers, including figures and tables, should be limited to 6 camera-ready pages. Please limit your paper by Begin typing the 1st line of heading 15 mm from the writing concisely, not by reducing the figures to a size at top of the first page of the paper. which their labels will be difficult to read. Succeeding pages have no heading. Manuscripts should be submitted in PDF format. High quality setting in PDF conversion is preferred. The 3.4 Paper Title and Authors PDF file should be less than 3 MB. The first page of each paper is to contain the title of the paper, the author's (authors') name(s) and affiliation(s) 3. TYPING AND ORGANIZATION within the title box of the width 160 mm. 3.1 Paper Size (a) Begin typing the title 40 mm from the top of the first Authors are requested to type your manuscript on page. Type the title centered, 12-pt. Times Roman (or an papers of the size 210 mm  297 mm (A4). equivalent typeface) boldface, in all capital letters with a single line spacing. All lines (run-over lines of a long title) 3.2 Typing should be centered. Type your manuscript in two columns. Each column Skip one (1) line between the title and the first author. has 85 mm width and the spacing between two columns is (b) Type author's name centered under the title, 10-pt. Times Roman (or an equivalent typeface) boldface, in must have SI units. All dimensionless groups and upper and lowercase letters. coefficients must be indicated as dimensionless after their Type author's affiliation information 10-pt., in upper definitions. All Latin symbols (dimensional and and lowercase letters with a single line spacing. dimensionless) should be listed in an alphabetic order. All Skip one-line space between the first and subsequent Greek symbols follow the Latin symbols. Subscripts and author group (if any). superscripts follow Greek symbols. Symbols should be italicized throughout the text. 3.5 Abstract Begin your abstract (150 words maximum), leaving 5. TABLES AND FIGURES two-line space between the first line and the author’s (a) Brief and descriptively title each table and caption each affiliation, 100 mm (or more) from the top of the first page. figure. Place table title above the table; place figure caption The ABSTRACT heading must be typed 10-pt. Times below the figure. Text and symbols must be clearly Roman (or equivalent) boldface in all capitals. It should be readable, avoid small symbols. flush with the left-hand margin of the column. (b) Refer to each table and figure in the text. If possible, Skip one-line space and type 5 to 10 keywords. place tables and figures in the order mentioned in the text as Leave two-line space between the keywords and the close as possible to text reference. top of body of the text. (c) Allow one line off space between the table or figure and the adjacent text. 3.6 Succeeding Pages (d) High-quality reproduction of illustrations depends on The first line of the text on all pages after the first the condition of the original artwork. It should be prepared (title page) is to start below 20 mm from the top of the as carefully as the text. All figures should be clear, sharp, paper. Do not type heading on these pages. and of high quality. (e) Proceedings will be printed in black and white. 3.7 Organization Use only two values of internal subheadings: 6. REFERENCES (a) Type first-value heads in all capital letters, boldface, References to cited literature should be identified in flush with the left-hand margin of the column. Put them on the text in square brackets and grouped at the end of the a line separate from the text, leaving a line of space above. paper in numerical order of appearance. References should You can number first-value heads, using single numbers. be styled and punctuated according to the following (b) For second-value heads, capitalize only the first letter of examples: journal article [1], book [2], thesis [3], each major word, boldface. Also, put them on a separate proceedings [4], and edited book [5]. line with one line of space above. (c) Third-value heads should be avoided if possible. If they 1. Asano, H., Akita, K. and Inoue, M., Effect of Gravity are essential, type them as part of the first following on Pool Boiling Heat Transfer on Thermal Spray paragraph. Leave no space above or below the head, indent Coating, Microgravity Science and Technology, 19(3- it five spaces, capitalize only the first letter of the head, 4) (2007), pp.90-92. underline it, follow it by a full stop and then immediately 2. Takenaka, N. and Ozawa, M., Introduction to by the text. Do not number third-value heads. Example: Engineering Thermodynamics, (1996), Corona Publishing, Tokyo. H eat t ransfer . The heat transfer coefficient is defined 3. Ozawa, M., Study on Flow Instabilities in Boiling as …….. Channels, Ph.D. thesis, (1977), Osaka University, Osaka. 4. EQUATIONS, UNITS AND NOMENCLATURE 4. Jiang, L., Asano, H., Takenaka, N. and Sugimoto, K., (a) Equations should be typed. Allow one line of space Heat Transfer Characteristics of Boiling Two-Phase above and below. Number displayed equations Flow in a Plate Heat Exchanger, Proc. of Int. Conf. on consecutively from Eq. (1) to the end of the paper. Power Engineering 2007 (ICOPE-07), (2007), pp.455- Example: 461. 5. Ozawa, M., Flow Instability Problems in Steam u v w Generating Tubes, in S. Ishigai (ed.), Steam Power    0 x y z (1) Engineering, Chap.5, (1999), Cambridge University Press, New York. When referring to an equation in the text write "Eq. (1)", except at beginning of a sentence, where "Equation 7. ASSISTANCE (1)" should be used. For any question or problem concerning typing and (b) Each paper must have a separate nomenclature section organization of the paper, that lists in detail and unambiguously all the symbols used please contact in the text and their definitions. Each dimensional symbol Prof. Hitoshi Asano Secretary of the Scientific Committee Phone &Fax +81 (0)78 803 6122 E-mail [email protected] 8. MAILING ADDRESS

All countries except USA and China Please submit your manuscripts via the conference website. http://www.jsme.or.jp/pes/ICOPE-09 If you are unable to submit via the website, please send your manuscript in PDF by E-mail to Prof. Hitoshi Asano Secretary of the Scientific Committee of ICOPE-09 Department of Mechanical Engineering Kobe University 1-1 Rokkodai, Nada, Kobe 657-8501, Japan Phone & Fax +81 (0)78 803 6122 E-mail [email protected]

USA: Please send your manuscript in PDF by E-mail to Prof. David Y.S. Lou J.K. Ludwickson Distinguished Professor Department of Mechanical Engineering Director of Confucius Institute and Director of Office of China Initiatives University of Nebraska Lincoln Phone: +1-402-472-5370, Fax: +1-402-472-5372, E-mail: [email protected]

China: Please send your manuscript in PDF by E-mail to Prof. Fei Wang Institute for Thermal Power Engineering, Zhejiang University Phone: +86-571-87952628, Fax: +86-571-87952438, E-mail: [email protected]