Aluminum Clad Wood Patio Doors

SECTION 08251 ALUMINUM CLAD WOOD PATIO DOORS

Display hidden notes to specifier. (Don't know how? Click Here)

PART 1 GENERAL

1.1 SECTION INCLUDES

1.A. French inswing patio doors.

1.B. French outswing patio doors.

1.C. French sliding patio doors.

1.D. Bi- parting patio doors.

1.E. Hinged patio doors.

1.2 RELATED SECTIONS

2.A. Section 06100 - Rough Carpentry: Rough opening and framing for windows.

1.3 REFERENCES

3.A. AAMA/WDMA/CSA 101/I.S.2/A440 - NAFS - North American Fenestration Standard/Specification for windows, doors and skylights.

3.B. CSA A440S1 - Canadian Supplement to AAMA/WDMA/CSA 101/I.S.2/A440 - NAFS.

3.C. U.S. Department of Energy - Energy Star Windows Program.

3.D. National Resources Canada - Energy Star Windows Program.

3.E. National Fenestration Rating Council (NFRC) 100 - Procedure for Determining Fenestration Product U-factors.

3.F. National Fenestration Rating Council (NFRC) 200 - Procedure for Determining Fenestration 08251-1 Product Solar Heat Gain Coefficient and Visible Transmittance at Normal Incidence.

3.G. National Fenestration Rating Council (NFRC) 700 - Product Certification Program.

1.4 SUBMITTALS

4.A. Submit under provisions of Section 01300.

4.B. Product Data: Manufacturer's data sheets on each product to be used, including: 4.B.1. Preparation instructions and recommendations. 4.B.2. Storage and handling requirements and recommendations. 4.B.3. Installation methods.

4.C. Shop Drawings: Provide drawing elevations of each opening with details of rough openings, anchorage and installation.

4.D. Selection Samples: For each finish product specified, two complete sets of colour chips representing manufacturer's full range of available colours and patterns.

4.E. Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square representing actual product, colour, and patterns.

1.5 QUALITY ASSURANCE

5.A. Manufacturer Qualifications: Minimum 5 year experience manufacturing similar products.

5.B. Installer Qualifications: Minimum 2 year experience installing similar products.

5.C. Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship. 5.C.1. Finish areas designated by Architect. 5.C.2. Do not proceed with remaining work until workmanship is approved by Architect. 5.C.3. Refinish mock-up area as required to produce acceptable work.

1.6 PRE-INSTALLATION MEETINGS

6.A. Convene minimum two weeks prior to starting work of this section.

1.7 DELIVERY, STORAGE, AND HANDLING

7.A. Deliver and store products in manufacturer's unopened packaging bearing the brand name and manufacturer's identification until ready for installation.

08251-2 7.B. Handling: Handle materials to avoid damage.

1.8 PROJECT CONDITIONS

8.A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

1.9 SEQUENCING

9.A. Ensure that products of this section are supplied to affected trades in time to prevent interruption of construction progress.

1.10 WARRANTY

10.A. Manufacturer warrants the following for its door products: 10.A.1. Unless otherwise specifically noted, skilled labor to repair or replace any affected component shall be provided for two years from the date of delivery. 10.A.2. IGU failure (evidenced by moisture within the IGU caused by failure of the hermetic seal), manufacturer shall supply a replacement unit (or complete sash, including IGU, at manufacturer's discretion) for the failed unit free of charge for as long as the ownership of the home by the purchaser. 10.A.3. Factory Painted Aluminum Extrusions: Peeling, cracking, flaking or blistering under normal use, application and proper care are warranted for ten years from the date of delivery.

PART 2 PRODUCTS

2.1 MANUFACTURERS

1.A. Acceptable Manufacturer: Ply Gem Canada Windows & Doors , which is located at: 7140 40 St. S.E.; Calgary, AB, Canada T2C 2B6; Toll Free Tel: 800-297-6102; Email: request info (); Web: plygem.ca

1.B. Web: http://plygem.ca.

1.C. Substitutions: Not permitted.

1.D. Requests for substitutions will be considered in accordance with provisions of Section 01600.

2.2 PERFORMANCE REQUIREMENTS

2.A. Product Standard: Comply with AAMA/WDMA/CSA 101/I.S.2/A440 for minimum standards of performance, materials, components, accessories, and fabrication unless more stringent requirements are indicated.

08251-3 2.B. Performance Class and Grade: Rated per AAMA/WDMA/CSA 101/I.S.2/A440. 2.B.1. In Canada, Performance Grades for windows, doors and skylights shall be selected according to the Canadian Supplement A440S1 so as to be appropriate for the conditions and geographic location in which the window, door or skylight will be installed.

2.C. Thermal Transmittance: Tested and certified per NFRC 100 maximum total fenestration product U-factor.

2.D. Solar Heat-Gain Coefficient (SHGC): Tested and certified per NFRC 200 maximum total fenestration product SHGC.

2.3 FRENCH INSWING PATIO DOOR

3.A. Provide French inswing patio doors with wide stiles and rails, 1-3/4 inches (44 mm) door panels, adjustable hinges, and full-perimeter weatherstripping. 3.A.1. Product: Signature Series Patio Door as manufactured by Ply Gem Windows

3.B. Design/Configuration: Refer to Drawings. 3.B.1. Provide Sentry Multi-Point lock with door hardware and handle sets as follows: 3.B.1.a. Handle Set: Transitional. 3.B.1.b. Handle Set: Traditional. 3.B.1.c. Handle Set: Contemporary. 3.B.1.d. Handle Set: Classic. 3.B.1.e. Handle Set: Modern. 3.B.1.f. Finish: Painted. 3.B.1.f.1) Colour: White. 3.B.1.f.2) Colour: Beige. 3.B.1.f.3) Colour: Faux Bronze. 3.B.1.f.4) Colour: Matte Black. 3.B.1.g. Finish: Plated. 3.B.1.g.1) Colour: Brass 3.B.1.g.2) Colour: Antique Brass. 3.B.1.g.3) Colour: Brushed Chrome. 3.B.1.g.4) Colour: Polished Chrome. 3.B.1.g.5) Colour: Satin Nickel. 3.B.1.g.6) Colour: Oil Rubbed Bronze.

08251-4 3.B.2. 3/4 inch (19 mm) Insulated Glass Units as indicated or scheduled. 3.B.3. 1-3/4 inches (44 mm) panels with wide stiles and rails for a true French look available in full, 3/4 or 1/2 lite panels as indicated or scheduled. 3.B.4. 4-9/16 inches (116 mm) or 6-9/16 inches (167 mm) jambs made of clear wood as indicated or scheduled. 3.B.5. Exterior Casing: J-Channel. 3.B.6. Exterior Casing: 180 brick Mold. 3.B.7. Exterior Casing: 3-1/4 Williamsburg. 3.B.8. Exterior Casing: 3-1/2 Flat.

2.4 FRENCH OUTSWING PATIO DOOR

4.A. Provide French outswing patio doors aluminum-clad wood patio door with wide stiles and rails, 1-3/4 inches (44 mm) door panels and ball bearing hinges. Warm edge insulating Low-E glass and argon gas fill, double weather strip sealing and a bumper sill. 4.A.1. Product: Signature Series Patio Door as manufactured by Ply Gem Windows

4.B. Design/Configuration: Refer to Drawings. 4.B.1. Provide Sentry Multi-Point lock with door hardware and handle sets as follows: 4.B.1.a. Handle Set: Transitional. 4.B.1.b. Handle Set: Traditional. 4.B.1.c. Handle Set: Contemporary. 4.B.1.d. Handle Set: Classic. 4.B.1.e. Handle Set: Modern. 4.B.1.f. Finish: Painted. 4.B.1.f.1) Colour: White. 4.B.1.f.2) Colour: Beige. 4.B.1.f.3) Colour: Faux Bronze. 4.B.1.f.4) Colour: Matte Black. 4.B.1.g. Finish: Plated. 4.B.1.g.1) Colour: Brass 4.B.1.g.2) Colour: Antique Brass. 4.B.1.g.3) Colour: Brushed Chrome. 4.B.1.g.4) Colour: Polished Chrome. 4.B.1.g.5) 08251-5 Colour: Satin Nickel. 4.B.1.g.6) Colour: Oil Rubbed Bronze. 4.B.2. 3/4 inch (19 mm) Insulated Glass Units as indicated or scheduled. 4.B.3. 1-3/4 inches (44 mm) panels with wide stiles and rails for a true French look available in full, 3/4 or 1/2 lite panels as indicated or scheduled. 4.B.4. 4-9/16 inches (116 mm) or 6-9/16 inches (167 mm) jambs made of clear wood as indicated or scheduled. 4.B.5. Exterior Casing: J-Channel. 4.B.6. Exterior Casing: 180 Brickmould. 4.B.7. Exterior Casing: 3-1/4 Williamsburg. 4.B.8. Exterior Casing: 3-1/2 Flat.

2.5 FRENCH SLIDING PATIO DOOR

5.A. Provide French sliding patio doors configuration with full-perimeter weatherstripping, adjustable rollers and standard multi-point lock system. 5.A.1. Product: Sentry Series Patio Door as manufactured by Ply Gem Canada.

5.B. Design/Configuration: Refer to Drawings. 5.B.1. Provide Sentry Multi-Point lock with door hardware and handle sets as follows: 5.B.1.a. Handle Set: Transitional. 5.B.1.b. Handle Set: Traditional. 5.B.1.c. Handle Set: Contemporary. 5.B.1.d. Handle Set: Classic. 5.B.1.e. Handle Set: Modern. 5.B.1.f. Finish: Painted. 5.B.1.f.1) Colour: White. 5.B.1.f.2) Colour: Beige. 5.B.1.f.3) Colour: Faux Bronze. 5.B.1.f.4) Colour: Matte Black. 5.B.1.g. Finish: Plated. 5.B.1.g.1) Colour: Brass 5.B.1.g.2) Colour: Antique Brass. 5.B.1.g.3) Colour: Brushed Chrome. 5.B.1.g.4) 08251-6 Colour: Polished Chrome. 5.B.1.g.5) Colour: Satin Nickel. 5.B.1.g.6) Colour: Oil Rubbed Bronze. 5.B.2. 3/4 inch (19 mm) Insulated Glass Units as indicated or scheduled. 5.B.3. 1-3/4 inches (44 mm) panels with wide stiles and rails for a true French look available in full, 3/4 or 1/2 lite panels as indicated or scheduled. 5.B.4. 4-9/16 inches (116 mm) or 6-9/16 inches (167 mm) jambs made of clear wood as indicated or scheduled. 5.B.5. Exterior Casing: J-Channel. 5.B.6. Exterior Casing: 180 Brickmould. 5.B.7. Exterior Casing: 3-1/4 Williamsburg. 5.B.8. Exterior Casing: 3-1/2 Flat.

2.6 FINISH

6.A. Finish: Light colours are AAMA 2603 paint finish, dark colours are AAMA 2604. Dark colours have Enhanced Colour Protection coating of Kynar to protect from fading and chalking. 6.A.1. Interior Frame Colour: Natural Clear Wood. 6.A.2. Exterior Frame Colour: White. 6.A.3. Exterior Frame Colour: Beige. 6.A.4. Exterior Frame Colour: Cashmere. 6.A.5. Exterior Frame Colour: Sable. 6.A.6. Exterior Frame Colour: Slate Grey. 6.A.7. Exterior Frame Colour: Clear Anodized. 6.A.8. Exterior Frame Colour: Taupe. 6.A.9. Exterior Frame Colour: Hunter Green. 6.A.10. Exterior Frame Colour: Redwood. 6.A.11. Exterior Frame Colour: Brown. 6.A.12. Exterior Frame Colour: Black. 6.A.13. Allure Hardware: 6.A.13.a. Hardware Colour: White. 6.A.13.b. Hardware Colour: Black. 6.A.13.c. Hardware Colour: Beige. 6.A.14. Signature Hardware: 08251-7 6.A.14.a. Hardware Colour: White. 6.A.14.b. Hardware Colour: Beige. 6.A.14.c. Hardware Colour: Matte Black. 6.A.14.d. Hardware Colour: Faux Bronze. 6.A.14.e. Hardware Colour: Brass. 6.A.14.f. Hardware Colour: Antique Brass. 6.A.14.g. Hardware Colour: Chrome. 6.A.14.h. Hardware Colour: Brushed Chrome. 6.A.14.i. Hardware Colour: Satin Nickel. 6.A.14.j. Hardware Colour: Oil Rubbed Bronze.

6.B. Grille: 6.B.1. Design: 1 inch (25 mm) Flat GBG. 6.B.2. Design: 13/16 inch (21 mm) Flat GBG. 6.B.3. Design: 5/8 inch (16 mm) Flat GBG. 6.B.4. Design: 5/16 inch (8 mm) Flat GBG. 6.B.5. Design: 1 inch (25 mm) Contoured GBG. 6.B.6. Design: 3/4 inch (19 mm) Contoured GBG. 6.B.7. Design: 1 inch SDL. 6.B.8. Design: 2 inches SDL. 6.B.9. Pattern: Standard. 6.B.10. Pattern: Half Standard. 6.B.11. Pattern: Ladder. 6.B.12. Pattern: Heritage. 6.B.13. Pattern: Perimeter Heritage. 6.B.14. Pattern: Three Over One. 6.B.15. Pattern: Two Over Two. 6.B.16. Pattern: Two Over One.

2.7 GLAZING

7.A. Energy Performance: 7.A.1. 08251-8 ENERGY STAR Zone - Canada (2015): _____. 7.A.2. Section 9.36 Energy Efficiency: _____. 7.A.3. U-Value Metric: _____. 7.A.4. Energy Rating: _____. 7.A.5. SHGC: _____.

7.B. IGU Unit Construction: 7.B.1. Eco Max Shield 366. 7.B.1.a. Location/Elevation: _____. 7.B.1.b. Glass Product: _____. 7.B.2. Eco Shield 270. 7.B.2.a. Location/Elevation: _____. 7.B.2.b. Glass Product: _____. 7.B.3. Eco Gain 180. 7.B.3.a. Location/Elevation: _____. 7.B.3.b. Glass Product: _____. 7.B.4. Provide tinted glass as indicated or scheduled. 7.B.5. Provide obscure glass as indicated or scheduled. 7.B.6. Provide tempered glass as indicated or required to comply with local building codes. 7.B.7. Provide laminated (security) glass as indicated or scheduled.

PART 3 EXECUTION

3.1 EXAMINATION

1.A. Do not begin installation until substrates have been properly prepared.

1.B. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

3.2 PREPARATION

2.A. Clean surfaces thoroughly prior to installation.

2.B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 08251-9 INSTALLATION

3.A. Install in accordance with manufacturer's instructions and in proper relationship with adjacent construction. Sealing options should be chosen based on the best practices and codes prevalent for each situation/installation.

3.4 PROTECTION

4.A. Protect installed products until completion of project.

4.B. Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

08251-10