User Defined Waypoints

G1000 SAR Setup and Quick Reference Revision History Date Who Version Notes Summer 2008 NESA Initial Created at NESA by MAS Advanced Mission Aircrew School 06 Dec 2009 1st Lt V1 Adjusted formatting Todd Changed wording on Gamber many instructions CAPID 443746 13 Jan 2010 1st Lt V2 Changed lat/lon Todd representation from HH Gamber DD MM SS.S to HH DD CAPID MM.MM 443746 Changed nav angle setting to Mag North from True North 09 Apr 2010 1st Lt V3 Added revision history Next revision Todd Changed filename to expected 14 Gamber imply reference guide. Jul 10 CAPID Changed column breaks 443746 on reference guide Removed reference to TEL button on audio panel 08 Nov 2012 Capt V4 Made minor changes Jeremy highlighted in red. Sing CAPID 167724 Communication Setup Select the AUX page group MAP display settings Select AUX - SYSTEM SETUP COM1 and COM2 are used for Select the MAP page group Press DFLTS soft key to restore all aviation communications. Select the NAVIGATION MAP defaults page COM3 is used for CAP Press the MENU button, highlight AUX Page group settings. communications. “Map Setup”, and press ENT. Select the AUX page group Highlight the “MAP” Group. Select AUX – SYSTEM SETUP AUX is used for Becker (ELT) Press the MENU button again and Ensure the following settings: monitoring. select “Restore All Defaults” then TIME FORMAT – UTC press ENT NAV ANGLE – MAGNETIC To use COM3, press the COM3 Use the FMS knobs to ensure the POSITION – HDDD MM.MM MIC button. This will allow you following settings: MFD DATA BAR FIELDS: to talk and listen on COM3. ORIENTATION – NORTH UP FIELD 1 – GS AUTO ZOOM – Off FIELD 2 – DIS To monitor other COM channels, LAND DATA – On FIELD 3 – XTK select the COM1 or COM2 TRACK VECTOR – On FIELD 4 – BRG button. WIND VECTOR – On GPS CDI – SELECTED to 0.30 NM NAV RANGE RING – On Press the FMS knob to deactivate the TOPO DATA – On cursor TOPO SCALE – Off OBSTACLE DATA – On Press the FMS knob to deactivate the Delete all user flight plans and user cursor waypoints. Press the FPL button Setup map to display Lat/Long grids. Select the FLIGHT PLAN Select the MAP page group CATALOG page Select the NAVIGATION MAP Press the MENU button page Select “Delete All” Press the MENU button and press Press CLR for 2 seconds. ENT Select WPT page group While GROUP is highlighted, use Select the User Waypoint Info page small FMS knob to select the LAND Press the MENU button and Select group Delete All User Waypoints (if LAT/LON – TEXT – Med shown) LAT/LON – RNG – 30NM Press the FMS knob to deactivate the cursor Restore MFD AUX setup to factory MFD Setup settings SAR Quick Reference Create User Waypoint from present Store & Activate Flight Plan Sector Search Setup position Press the FPL key and turn the small Store and activate a flight plan Create User Waypoint Select the NAVIGATION MAP FMS knob to display the Flight Plan consisting of at least the search start Turn the large FMS knob to select page Catalog page. point. You may need to create a user the WPT page group. Push the joystick. The pointer is Press the NEW soft key to display a defined waypoint. Turn the small FMS knob to select displayed at the present position. blank FPL page. Press the FPL key the USER WPT INFORMATION Press ENT to create a waypoint in Use the FMS knobs to insert Press the FMS knob to activate the page. Press the NEW soft key that location waypoints. Press ENT after entering cursor, then use the large FMS knob Turn the FMS knobs to enter a name Turn the FMS knobs to select the each waypoint. to highlight the entry point. for the new waypoint. Press ENT. waypoint name. Press the ACTIVE soft key to Press MENU, select Search and Turn the FMS knobs to enter the Press ENT to accept the selected activate the stored flight plan. Rescue, and press ENT position coordinates. name. Select the Sector pattern Turn the large FMS knob to move Press CLR for 2 seconds to go to Parallel Track Search Setup Configure the remaining fields as the cursor to the desired field and navigation page. Store and activate a flight plan necessary turn the small FMS knob to make consisting of the four corners of your changes. Press ENT when finished. Create a User Waypoint referenced grid. Expanding Square Search Setup Press CLR for 2 seconds to go to from another Waypoint Press the FPL key Store and activate a flight plan Navigation Map page. With the USER WPT Press the FMS knob to activate the consisting of at least the sector’s INFORMATION page displayed, cursor center. You may need to create a Modify a User Waypoint press the NEW softkey to enter a Use the large FMS knob to highlight user defined waypoint. Go to WPT- User WPT Info waypoint. the grid entry point. Press the FPL key With the USER WPT INFOR page Turn the FMS knobs to name the Press MENU, select Search and Press the FMS knob to activate the displayed, press the FMS knob to waypoint. Rescue, and press ENT cursor, then use the large FMS knob activate the cursor. Press ENT. This will move the Select the Parallel pattern. to highlight the grid entry point. Turn the FMS knobs, to select the cursor to the reference waypoint Configure the remaining fields as Press MENU, select Search and waypoint name area. necessary. Rescue, and press ENT NOTE: If you are prompted to add a Turn the small FMS knob CCW to - Leg length is 7.5nm Select the EXP SQR pattern waypoint with the given name, you bring up the waypoint reference -Number of legs is 9 Configure the remaining fields as have not chosen a valid user window. You can reference from the -Select Activate SAR and press necessary. waypoint. FPL, NRST or RECENT, ENT. Turn the FMS knobs to make Turn the Large FMS knob to cursor changes to the user waypoint down through the list of waypoints. Press ENT to accept the changes. Press ENT to select that waypoint. Press CLR key for 2 seconds to go The RADIAL is the angle to that to navigation page. point, and DIS is the distance. Turn the FMS knobs to make changes. Press ENT when finished. Press the CLR for 2 seconds to go to navigation page.