Installation Manual Suspension Control Module LCM - V2

Read Before Installation 4

W215 2002 - 2006 38 Contents CL-class W216 2007 - 2013 7

W219 2004 - 2011 9 CLS-class W218 2012+ 30

W211 2004 - 2009 9

E-class W212 2010+ 30

W207 2010+ 30

X164 2006 - 2012 10 GL-class X166 2013+ 18

W164 2006 - 2011 10 ML-class W166 2012+ 18

R-class W251 2006 - 2012 14

W220 2000 - 2006 7

S-class W221 2007 - 2013 7 future W222 2014+ release R230 2003 - 2012 34 SL-class R231 2013+ 34

Ride Height Adjustment 42

Vehicle Connector Preparation 44

Warranty and Return Policy 48 Read Before Installation

Welcome: The concept explained: What is in the package: Required tools: Installation concept:

Warning: Suspension Control Module should be installed by an individual with extensive knowledge in electronics, wire identifcation and experience in extracting pins from the connector housing. Programa is not responsible for any damage to the module or related devices due to improper installation.

Ride Height: To retain proper ride comfort and to avoid damage to suspension components please follow these minimum recommended height adjustments: All non-AMG Mercedes models should use a setting of 3 or higher. AMG cars are lower than their Mercedes counterparts. With this in mind it is recommended that AMG cars use a ride height setting of 5 or higher. Lower settings can be used for show purposes but are not recommended for everyday driving. In some models the door must be closed in order for the Airmatic or ABC system to operate. This is a safety function and is normal on those vehicles.

Servicing your Mercedes: When having the vehicle serviced, always disable the Suspension Control Module by setting the height to factory level. This will prevent the possible missdiagnosing of the vehicle electronic system by the technician.

Technical Support: For further information, please contact the manufacturer: ProgRama Inc. (toll free in USA): +1-866-961-7362.

4 5 6 Airmatic or ABC suspension? 216 chassis CL 2007 - 2013 220 chassis S 2000 - 2006 221 chassis S 2007 - 2013

Both CL-class and S-class vehicles were manufactured with two kinds of suspensions: - an air suspension (Airmatic), or - the higher quality hydraulic suspension (ABC = Active Body Control).

You must know which type of suspension is in the vehicle before you can install the ProgRama Suspension Lowering Control Module. One obvious diference between the two suspensions is the speed of changing the vehicle height. In general, if you have the more expemsive ABC suspension and you change the vehicle height with the Mercedes control button in the cabin, the change will be instante- nous. On other hand, the same with the Airmatic air suspension takes many seconds. If the vehicle is all-wheel drive, it will have the Airmatic suspension, as the ABC is available only on rear-wheel drive models. Each vehicle equipped with ABC has an “ABC Sport” button that allows the driver to adjust the suspension range for diferent driving style preferences. If you have this button in the cabin, continue with ABC section on page 34. If still in doubts, contact any Mercedes dealer with your VIN number and they can tell you which suspension you have. Next, continue with the installation from the appropriate page:

S-class (W220) page 22

Airmatic S-class (W221) page 26

CL-class (W216) page 26

ABC CL- or S-class page 34

7 8 Which Airmatic sensors? 219 chassis CLS 2004 - 2011 211 chassis E 2004 - 2009

Both CLS-class and E-class vehicles were assembled with one of two kinds of height sensors, either: - height sensor with 4-wires, or - height sensor with 3-wires.

You must know which type of sensor is in the vehicle before you can install the ProgRama Suspension Lowering Control Module. In general, all AMG models wre manufactured using 4-wire sensors. For AMG vehicles, continue with page 22. All non-AMG vehicles manufactured before 05/2005 were assembled using 4-wire height sensors, continue with page 22. Newer vehicles were assembled using 3-wire sensors, continue with page 26. One can also locate one of the three height sensors, disconnect its connector and see how many pins are in the connector, three or four. Next, continue with the installation from the appropriate page:

Airmatic page 22 AMG 4-wire sensors

CLS-class (W219) Airmatic page 22 before 05/2005 4-wire sensors

CLS-class (W219) Airmatic page 26 after 05/2005 3-wire sensors non - AMG E-class (W211) Airmatic page 22 before 05/2005 4-wire sensors

E-class (W211) Airmatic page 26 after 05/2005 3-wire sensors

9 10 ML-class (W164 2006-2012) GL-class (X164 2006-2012) A I R M A T I C Air1 B22/7 Left Rear Airmatic (N51) Harness in the vehicle, Female vehicle, Pin the in ViewHarness (N51) Airmatic W164 chassis X164 chassis Conn 1 Conn

B22/10 Right Rear Rear RR LR

21 B22/10 Right Rear ML Battery GL

25 B22/7 Left Rear Airmatic Airmatic *NOTE: CANC L

wires with electrical tape wires withelectrical Insulate each of these two H Green Green-White Conn 3 Conn 2006 -2011 2006 -2012

L CANC-L

H CANC-H RF LF

24 48 B22/9 Right Front 47

23 47 +12 V

22 46 Not Used* Not Used* Not Used Not Used 21

21 45 GND B22/8 Left Front 20 44 Female (part oftheharness) (part Connector 19 43 8 pin 18 42 Remote Remote Control Control 17 41 Orange 2 1 3 5 6 2 7 1 8 4 Green 40 16 40 Black B22/9 Right Front Back view Male pins Red Pin View Pin Female 15 39 10 11 12 13 8 pin Male 1 2 3 4 5 6 7 8 9 38 14 38 B22/8 Left Front 14 15 16 17 18 19 20 21 22 23 24 25 26 13 37 16 12 36 11 35 10 34 5 1 16 33 9 6 2 32 8 Yellow Yellow Yellow Brown Brown Brown Green Green White White Black 7 3 31 7 Gray Gray Blue Blue Red Module Connector Control Suspension 30 6 8 4 29 5 28 23 10 14 22 25 24 13 26 15 12 11 4 6 4 3 2 5 27 3 26 2 25 1 Conn 2 Conn 11 ML-class (W164 2006-2012) GL-class (X164 2006-2012) A I R M A T I C 12 ML-class (W164 2006-2012) GL-class (X164 2006-2012) A I R M A T I C

LEFT FRONT LEFT REAR RIGHT REAR STEP-BY-STEP INSTALLATION CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR CAR HARNESSCONNECTOR...CAR DISCONNECT THE BATTERY 21 25 164 chassis:Airmatic (N51)control unit REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM Vehicle‘s Battery on page44. Connector Preparation Refer to Vehicle‘s 9 5 1 38 ... AND INSERT ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN ... AND INSERT ITINTO... ANDINSERT 8-PIN CONNECTOR CONNECTOR CONNECTOR must click! click! 10 6 2 1 6 2 Shell backview FemaleEmpty back view Female Shell back view Female Shell 8 4 8 4 8 4 7 3 7 3 7 3 6 2 2 6 6 2 5 1 5 1 5 1 INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULE HARNESS 25 21 Yellow White click! must click! INSERT PINFROM INSERT PINFROM INSERT INSERT PINFROM INSERT Left frontLeft footwell (underdriver‘s seat) 11 23 4 3 7 3 38 Brown

25 21 23 CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY 12 8 4 Battery the Disconnect 38 4 3 BATTERY +12V BATTERY GND CANC - L CANC - H RIGHT FRONT CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR screws and remove remove and screws the Suspension Suspension the REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM the cover Unscrew Unscrew Module Module L H + BATTERY Green-White Green 47 29 25 21 17 13 33 - BATTERY 21 40 Switch (black button) button) (black Switch ... AND INSERT ITINTO... ANDINSERT 2-PIN ITINTO... ANDINSERT 2-PIN ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN Rotate the Function Function the Rotate + BATTERY - BATTERY to position 2 position to CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR click! click! click! click! click! 30 26 22 18 14 34 2 1 8 4 7 Shell backview FemaleEmpty back view Female Shell back view Female Shell back view Female Shell back view Female Shell 4 8 8 4 8 4 2 1 1 2 7 3 7 3 3 7 6 2 6 2 6 2 5 1 5 1 5 1

Ride Height Adjustment INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULEHARNESS BACK BACK Orange MALE MALE Green 2 1 1 2

VIEW VIEW

INSERT PINFROM INSERT PINFROM INSERT INSERT PINFROM INSERT PINFROM INSERT INSERT PINFROM INSERT To continue, continue, To on page42 2 H 1 L go to to go click! click! 47 19 15 31 27 23 35 10 21 Red 4 8 click! click! Black 40 BACK BACK click! Gray 5 1 5 1 MALE MALE

6 2 6 2

VIEW VIEW 7 3 7 3

8 4 8 4

8 4 4 8 7 3 7 3 1) 1) 10 4 8 CHECK CONTINUITY 6 2 6 2 CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY 1) 1) 5 1 5 1 2 1 2) H L 2) MALE MALE Red Black 47 20 16 32 28 24 6 5 21

FRONT FRONT 2) 2) REMOTE REMOTE 2 1 2 1 40 14 22

VIEW VIEW MALE MALE

CONTROL CONTROL 13 ML-class (W164 2006-2012) GL-class (X164 2006-2012) A I R M A T I C 14 R-class (W251 2006-2012) A I R M A T I C Air2 B22/7 Left Rear Airmatic (N51) Harness in the vehicle, Female vehicle, Pin the in ViewHarness (N51) Airmatic 251 chassis Conn 1 Conn

B22/10 Right Rear Rear RR LR

21 B22/10 Right Rear R Battery

25 B22/7 Left Rear Airmatic *NOTE: CANC L

Green H Green-White wires with electrical tape wires withelectrical Insulate each of these two Conn 3 Conn all years L CANC-L

H CANC-H RF LF

24 48 B22/9 Right Front 47

23 47 +12 V

22 46 Not Used* Not Used* Not Used Not Used 21

21 45 GND B22/8 Left Front 20 44 Female (part oftheharness) (part Connector 19 43 8 pin 18 42 Remote Remote Control Control 17 41 Orange 2 1 3 5 6 2 7 1 8 4 Green 40 16 40 Back view Black

B22/9 Right Front Male pins Red Pin View Pin Female 15 39 8 pin Male 10 11 12 13 1 2 3 4 5 6 7 8 9 38 14 38 B22/8 Left Front 14 15 16 17 18 19 20 21 22 23 24 25 26 13 37 16 12 36 11 35 10 34

16 33 9 5 1 32 8 Yellow Yellow Yellow Brown Brown Brown Green Green White White Black 6 2 31 7 Gray Gray Blue Blue Red Module Connector Control Suspension 30 6 7 3 29 5 8 4 28 23 10 14 22 25 24 13 26 15 12 11 4 4 3 2 5 6 27 3 26 2 25 1 Conn 2 Conn 15 R-class (W251 2006-2012) A I R M A T I C 16 R-class (W251 2006-2012) A I R M A T I C

LEFT FRONT LEFT REAR RIGHT REAR STEP-BY-STEP INSTALLATION CAR HARNESSCONNECTOR...CAR CAR HARNESSCONNECTOR...CAR CAR HARNESSCONNECTOR...CAR DISCONNECT THE BATTERY 21 25 REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM 251 chassis:Airmatic (N51)withADS Vehicle‘s Battery on page44. Connector Preparation Refer to Vehicle‘s 9 5 1 38 ... AND INSERT ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN ... AND INSERT ITINTO... ANDINSERT 8-PIN CONNECTOR CONNECTOR CONNECTOR must click! click! 10 6 2 1 6 2 Shell backview FemaleEmpty back view Female Shell back view Female Shell 8 4 8 4 8 4 7 3 7 3 7 3 6 2 6 2 6 2 5 1 5 1 5 1 INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULE HARNESS 21 25 Right frontRight footwell (underpassengerseat) Yellow White click! must click! INSERT PINFROM INSERT INSERT PINFROM INSERT INSERT PINFROM INSERT 11 23 4 3 7 3 38 Brown

25 21 23 CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY 12 8 4 Battery the Disconnect 38 3 4 BATTERY +12V BATTERY GND CANC - L CANC - H RIGHT FRONT CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR screws and remove remove and screws the Suspension Suspension the REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM the cover Unscrew Unscrew Module Module L H + BATTERY Green-White Green 47 21 17 13 29 25 33 - BATTERY 21 40 Switch (black button) button) (black Switch ... AND INSERT ITINTO... ANDINSERT 2-PIN ITINTO... ANDINSERT 2-PIN ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN Rotate the Function Function the Rotate + BATTERY - BATTERY to position 2 position to CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR click! click! click! click! click! 26 22 18 14 30 34 2 1 8 4 7 Shell backview FemaleEmpty back view Female Shell back view Female Shell back view Female Shell back view Female Shell 8 4 8 4 8 4 2 1 2 1 7 3 7 3 7 3 6 2 6 2 6 2 5 1 5 1 5 1

VIEW VIEW

6 2 6 2

VIEW VIEW 7 3 7 3

8 4 8 4

8 4 8 4 7 3 7 3 1) 1) 10 4 8 CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY 6 2 6 2 1) 1) 5 1 5 1 2 1 2) H L Red Black 2) MALE MALE 47 20 16 32 28 24 6 5 21

FRONT FRONT 2) 2) REMOTE REMOTE 2 1 2 1 40 14 22

VIEW VIEW MALE MALE

CONTROL CONTROL 17 R-class (W251 2006-2012) A I R M A T I C 18 ML-class (W166 2012+) GL-class (X166 2013+) A I R M A T I C Air5 B22/7 Left Rear Airmatic (N51/3) Harness in the vehicle, Female vehicle, Pinthe in Harness View (N51/3) Airmatic W166 chassis X166 chassis

B22/10 Right Rear Rear RR LR ML Battery GL Airmatic Airmatic *NOTE: CANE1 L

wires with electrical tape wires withelectrical Insulate each of these two Green Green-White H 2 1 2012+ 2013+ RF LF

24 48 B22/9 Right Front 47

23 47 +12 V Red

22 46 Not Used* Not Used* Not Used Not Used 21

21 45 GND Black B22/8 Left Front 20

20 44 CANE1-H Orange Female (part oftheharness) (part 19 Connector 19 43

CANE1-L Green 8 pin 18 42 Remote Remote Control Control 17 41 3 5 6 2 7 1 8 4 16 40 Back view Male pins Pin View Pin Female 15 39 38 10 11 12 13 Male 8 pin

B22/7 Left Rear 1 2 3 4 5 6 7 8 9 14 38 37 14 15 16 17 18 19 20 21 22 23 24 25 26

13 37 B22/8 Left Front 16 36 12 36 B22/9 Right Front 11 35 35 B22/10 Right Rear 10 34 5 1 16 33 9 6 2 32 8 Yellow Yellow Yellow Brown Brown Brown Green Green White White Black 7 3 31 7 Gray Gray Blue Blue Red Module Connector Control Suspension 30 6 8 4 29 5 28 10 23 14 22 25 24 13 26 15 12 11 4 4 3 2 5 6 27 3 26 2 Conn M Conn 25 1 19 ML-class (W166 2012+) GL-class (X166 2013+) A I R M A T I C 20 ML-class (W166 2012+) GL-class (X166 2013+) A I R M A T I C

LEFT FRONT LEFT REAR RIGHT REAR on page44. Connector Preparation Refer to Vehicle‘s CAR HARNESSCONNECTOR...CAR CAR HARNESSCONNECTOR...CAR CAR HARNESSCONNECTOR...CAR DISCONNECT THE BATTERY REMOVE PINFROM Left frontLeft footwell (underdriver‘s seat) REMOVE PINFROM REMOVE PINFROM Vehicle‘s Battery 1 9 5 37 35 38 ... AND INSERT ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN ... AND INSERT ITINTO... ANDINSERT 8-PIN CONNECTOR CONNECTOR CONNECTOR must click! click! 10 2 6 1 6 2 Shell backview FemaleEmpty back view Female Shell back view Female Shell 8 4 8 4 8 4 7 3 7 3 7 3 6 2 6 2 6 2 5 1 5 1 5 1 INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULE HARNESS INSERT PINFROM INSERT INSERT PINFROM INSERT INSERT PINFROM INSERT must click! must click! 3 4 11 23 7 3 White Yellow 37 Brown 35 38

23 CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY 3 4 12 8 4 37 35 38 BATTERY +12V BATTERY GND CANE1 - L CANE1 - H RIGHT FRONT CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR Green-White screws and remove remove and screws the Suspension Suspension the REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM the cover Green Unscrew Unscrew Module Module + BATTERY 47 21 17 13 29 25 33 - BATTERY 21 19 20 36 Switch (black button) button) (black Switch ... AND INSERT ITINTO... ANDINSERT 2-PIN ITINTO... ANDINSERT 2-PIN ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN Rotate the Function Function the Rotate + BATTERY - BATTERY to position 2 position to CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR click! click! click! click! click! 26 22 18 14 30 34 1 8 4 7 2 Shell backview FemaleEmpty back view Female Shell back view Female Shell back view Female Shell back view Female Shell 8 4 8 4 8 4 2 1 2 1 7 3 7 3 7 3 6 2 6 2 6 2 5 1 5 1 5 1

VIEW VIEW VIEW VIEW 7 3 7 3

INSERT PINFROM INSERT PINFROM INSERT INSERT PINFROM INSERT INSERT PINFROM INSERT INSERT PINFROM INSERT To continue, continue, To 8 4 8 4 on page42 2 1 go to to go 4 8 47 19 15 31 27 23 35 10 21 Red click! 20 19 click! Black Orange Orange 36 click! click! click! Gray

8 4 8 4 7 3 7 3 1) 1) 10 4 8 CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY 6 2 6 2 1) 1) 5 1 5 1 2 1 2) Red Black 2) MALE MALE 47 20 16 32 28 24 6 5 21

FRONT FRONT 20 19 2) 2) REMOTE REMOTE 2 1 2 1 36 14 22

VIEW VIEW MALE MALE

CONTROL CONTROL 21 ML-class (W166 2012+) GL-class (X166 2013+) A I R M A T I C Air4

Female Suspension Control 211 chassis E Airmatic 4-wire sensors 2004 till 05/2005 Pin View Module Connector 219 chassis CLS Airmatic 4-wire sensors 2004 till 05/2005 13 26 12 25 11 24 4-wire sensors 4-wire 220 chassis S Airmatic 4-wire sensors 2000–2006 10 23 9 22 8 21 7 20 6 19 5 18 4 17 3 16 2 15 LR 1 14

A I R M A T I C A I R M LF

Rear Remote Control

Connector 16 16 Battery W220)

( RF Male pin View 1 2 3 4 Back View RR CANC 5 6 7 8 L H

8 pin 8 pin Brown Female Male 6

B22/3 Rear B22/3 Rear B22/9 Right Front B22/9 Right Front Front B22/8 Left Front B22/8 Left Yellow Green-White 5

S-class 4 Green 8 Yellow 1 11 Gray 7 12 Green 2 15 White 6 2 Blue (W211) 5 26 Brown 3 13 Yellow 4 White 3 Green Orange

Black

E-class 1 22 Red 2 14

Red Black

Green 24 (W219)

Gray 10 Blue 25 Brown 23 B22/9-1 Right Front Front B22/8-1 Left B22/9-2 Right Front Front B22/8-2 Left B22/3-2 Rear B22/3-1 Rear CANC-L CANC-H V +12 GND CLS-class 21 25 L H 47 21 40 38 36 34 Conn I Conn M

48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25

20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Conn C 24 23 22 21

Airmatic (N51) Harness in the vehicle, Female Pin View 22

Disconnect the STEP-BY-STEP INSTALLATION Battery 4-wire sensors 4-wire Right front upper footwell Pull the carpet back A I R M A T I C A I R M

W220) (

Unscrew 3 bolts holding the aluminum bracket Airmatic (N51) with ADS S-class (W211)

DISCONNECT THE BATTERY E-class Vehicle‘s Battery

REMOVE PIN FROM ... AND INSERT IT INTO 8-PIN INSERT PIN FROM CHECK CONTINUITY CAR HARNESS CONNECTOR... CONNECTOR LOWERING MODULE HARNESS INTO CAR HARNESS CONNECTOR (W219)

Empty Female White Shell back view 3 Refer to Vehicle‘s Connector Preparation 4 3 2 1 3 on page 44. 6 8 7 6 5 must click! 21 21 21 must click!

1 2 3 4

REMOVE PIN FROM ... AND INSERT IT INTO 8-PIN INSERT PIN FROM CHECK CONTINUITY CAR HARNESS CONNECTOR... CONNECTOR LOWERING MODULE HARNESS R E A S N O INTO CAR HARNESS CONNECTOR CLS-class Female Shell Yellow back view 4

4 3 2 1 4 2 8 7 6 5 click! 25 25 25 click!

5 6 7 8 23

REMOVE PIN FROM ... AND INSERT IT INTO 8-PIN INSERT PIN FROM CHECK CONTINUITY CAR HARNESS CONNECTOR... CONNECTOR LOWERING MODULE HARNESS INTO CAR HARNESS CONNECTOR Female Shell back view 23

4-wire sensors 4-wire Brown 4 3 2 1 23 1 8 7 6 5

34 34 34

A I R M A T I C A I R M 9 10 11 12

INSERT PIN FROM CHECK CONTINUITY

REMOVE PIN FROM ... AND INSERT IT INTO 8-PIN CAR HARNESS CONNECTOR... CONNECTOR LOWERING MODULE HARNESS INTO CAR HARNESS CONNECTOR Female Shell L E F T F R O N T S E N O R T F R O N L E F back view 10 Gray 4 3 2 1 10

W220) 7 8 7 6 5 ( click! 38 38 38 click!

13 14 15 16

REMOVE PIN FROM ... AND INSERT IT INTO 8-PIN INSERT PIN FROM CHECK CONTINUITY CAR HARNESS CONNECTOR... CONNECTOR LOWERING MODULE HARNESS INTO CAR HARNESS CONNECTOR

S-class Female Shell back view 25 Blue 4 3 2 1 25 3 8 7 6 5

36 36 36

(W211) 17 18 19 20

REMOVE PIN FROM ... AND INSERT IT INTO 8-PIN INSERT PIN FROM CHECK CONTINUITY CAR HARNESS CONNECTOR... CONNECTOR LOWERING MODULE HARNESS INTO CAR HARNESS CONNECTOR Female Shell

R I G H T F R O N T S E N O R T F R O N R I G H back view 24 Green 4 3 2 1 24 5 8 7 6 5

E-class click! 40 40 40 click!

21 22 23 24

REMOVE PIN FROM ... AND INSERT IT INTO 8-PIN INSERT PIN FROM CHECK CONTINUITY CAR HARNESS CONNECTOR... CONNECTOR LOWERING MODULE HARNESS MALE FRONT VIEW INTO CAR HARNESS CONNECTOR 4 3 2 1 (W219) 8 7 6 5 Green-White Female Shell REMOTE CONTROL back view 4 1 2 3 4 6 Orange 5 6 7 8 4 4 3 2 1 MALE 2) 4 1) CANC - H 8 7 6 5 BACK VIEW click! H H H click!

17 18 19 20

REMOVE PIN FROM ... AND INSERT IT INTO 8-PIN INSERT PIN FROM CHECK CONTINUITY CAR HARNESS CONNECTOR... CONNECTOR LOWERING MODULE HARNESS MALE FRONT VIEW CLS-class INTO CAR HARNESS CONNECTOR 4 3 2 1 Female Shell 8 7 6 5 REMOTE CONTROL Green 1 2 3 4 back view 8 5 Green 5 6 7 8 8 4 3 2 1 2) MALE 8 1) CANC - L 8 7 6 5 BACK VIEW click! L L L click!

21 22 23 24 24

REMOVE PIN FROM ... AND INSERT IT INTO 2-PIN INSERT PIN FROM CHECK CONTINUITY CAR HARNESS CONNECTOR... CONNECTOR LOWERING MODULE HARNESS Black MALE INTO CAR HARNESS CONNECTOR 1 1 2 1 1 BATTERY BATTERY Empty Female

Black sensors 4-wire - - Shell back view 2 MALE 1) 2) 1 1 BACK VIEW 2 BATTERY GND BATTERY click! 22 21 21 21 click!

25 26 27 28 T I C A I R M

INSERT PIN FROM CHECK CONTINUITY REMOVE PIN FROM ... AND INSERT IT INTO 2-PIN CAR HARNESS CONNECTOR... CONNECTOR LOWERING MODULE HARNESS MALE INTO CAR HARNESS CONNECTOR 1 Red Female Shell 2 2 1

BATTERY BATTERY back view 2 2 Red + + 1 MALE 1) 2) 2 2 BACK VIEW W220) ( BATTERY +12V BATTERY click! 14 47 47 47 click!

29 30 31 32

Unscrew S-class To continue, the Suspension Rotate the Function go to Module Switch (black button) Ride Height Adjustment screws and remove to position 1 on page 42 the cover

33 34 35 (W211)

E-class (W219)

CLS-class

25 26 CLS-class W219, CL-class W216, E-class W211, S-class W221 A I R M A T I C 3-wire sensors Air3

B22/3 Rear Airmatic (N51) Harness in the vehicle, Female vehicle, Pin the in ViewHarness (N51) Airmatic 221 chassis 219 chassis 211 chassis Conn I Conn Rear RR LR CLS S E Battery

25 B22/3 Rear Airmatic Airmatic Airmatic *NOTE: CANC L

Green H Green-White end using electrical tape end usingelectrical wire unused each Insulate 3-wire sensors 3-wire sensors 3-wire sensors Conn C Conn

L CANC-L

H CANC-H RF LF

24 48 B22/9 Right Front from 05/2005 from 05/2005 47 2007- 2013

23 47 +12 V 22 46 Not Used* Not Used* Not Used* Not Used Not Used Not Used 21

21 45 GND B22/8 Left Front 20 44 Female Connector 19 43 8 pin Male pin View 18 42 Remote Remote Control Control 17 41 Back View Orange 2 1 6 1 3 2 5 7 8 4 Green 40 16 40

B22/9 Right Front Black Red Pin View Pin Female Male 8 pin 15 39 10 11 12 13 1 2 3 4 5 6 7 8 9 38 14 38 B22/8 Left Front 14 15 16 17 18 19 20 21 22 23 24 25 26 13 37 16 12 36 11 35 10 34 5 1 16 33 9 6 2 32 8 Yellow Yellow Yellow Brown Brown Brown Green Green White White Black 7 3 31 7 Gray Gray Blue Blue Red Module Connector Control Suspension 30 6 8 4 29 5 28 10 24 14 22 25 23 11 13 15 26 12 4 4 3 2 5 6 27 3 26 2 Conn M Conn 25 1

Disconnect the STEP-BY-STEP INSTALLATION Battery 3-wire sensors 3-wire Right front upper footwell Pull the carpet back A I R M A T I C A I R M

W221

Unscrew 3 bolts holding the aluminum bracket Airmatic (N51) with ADS S-class W211,

DISCONNECT THE BATTERY E-class

Vehicle‘s Battery W216,

REMOVE PIN FROM ... AND INSERT IT INTO 8-PIN INSERT PIN FROM CHECK CONTINUITY CAR HARNESS CONNECTOR... CONNECTOR LOWERING MODULE HARNESS INTO CAR HARNESS CONNECTOR Female Shell Yellow back view 4 CL-class

4 3 2 1 4 REAR 2 8 7 6 5 click! 25 25 25 click! W219,

5 6 7 8

38 38 CLS-class 38

9 10 11 12 27 28 CLS-class W219, CL-class W216, E-class W211, S-class W221 A I R M A T I C 3-wire sensors

BATTERY +12V BATTERY GND CANC - L CANC - H RIGHT FRONT CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR screws and remove remove and screws the Suspension Suspension the REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM the cover Unscrew Unscrew Module Module L H + BATTERY 47 Green-White Green 25 21 17 13 29 29 - BATTERY 21 40 Switch (black button) button) (black Switch ... AND INSERT ITINTO... ANDINSERT 2-PIN ITINTO... ANDINSERT 2-PIN ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN Rotate the Function Function the Rotate + BATTERY - BATTERY to position 1 position to CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR click! click! click! click! click! 26 22 18 14 30 30 2 1 8 4 5 Shell backview FemaleEmpty back view Female Shell back view Female Shell back view Female Shell back view Female Shell 8 4 8 4 8 4 2 1 2 1 7 3 7 3 7 3 6 2 6 2 6 2 5 1 5 1 5 1

INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR Ride Height Adjustment INTO HARNESSCONNECTOR CAR LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULEHARNESS BACK BACK Orange MALE MALE Green 2 1 2 1

VIEW VIEW

INSERT PINFROM INSERT PINFROM INSERT INSERT PINFROM INSERT PINFROM INSERT INSERT PINFROM INSERT To continue, continue, To on page42 2 H 1 L go to to go click! click! 47 19 15 31 27 23 31 24 21 Red 4 8 click! click! Black 40 BACK BACK click! Green 5 1 5 1 MALE MALE

6 2 6 2

VIEW VIEW 7 3 7 3

8 4 8 4

8 4 8 4 7 3 7 3 1) 1) 24 4 8 CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY 6 2 6 2 1) 1) 5 1 5 1 2 1 2) H L Red Black 2) MALE MALE 47 20 16 32 28 24 6 5 21

FRONT FRONT 2) 2) REMOTE REMOTE 2 1 2 1 40 14 22

VIEW VIEW MALE MALE

CONTROL CONTROL

3-wire sensors 3-wire A I R M A T I C A I R M

W221

S-class W211,

E-class W216,

CL-class W219,

CLS-class

29 30 E-class (W207 / W212 2010+) CLS-class (W218 2012+) A I R M A T I C Air6 B22/7 Left Rear Airmatic (N51/3) Harness in the vehicle, Female vehicle, Pin the in ViewHarness (N51/3) Airmatic 218 chassis 212 chassis 207 chassis Conn 3 Conn

B22/10 Right Rear Rear RR LR

21 B22/9 Right Front CLS E E Battery

25 B22/8 Left Front Airmatic Airmatic Airmatic *NOTE: CANE L

Green H Green-White wires with electrical tape wires withelectrical Insulate each of these two Conn 2 Conn

L CANE-L 2010+ 2012+ 2010+

H CANE-H RF LF

24 48 B22/9 Right Front 47

23 47 +12 V

22 46 Not Used* Not Used* Not Used Not Used 21

21 45 GND B22/8 Left Front 20 44 Female (part oftheharness) (part Connector 19 43 8 pin 18 42 Remote Remote Control Control 17 41 Orange 2 1 3 5 6 2 7 1 8 4 Green 40 16 40 Back view B22/10 Right Rear Black Male pins Red Pin View Pin Female 15 39 8 pin Male 10 11 12 13 1 2 3 4 5 6 7 8 9 38 14 38 B22/7 Left Rear 14 15 16 17 18 19 20 21 22 23 24 25 26 13 37 16 12 36 11 35 10 34

16 33 9 5 1 32 8 Yellow Yellow Yellow Brown Brown Brown Green Green White White Black 6 2 31 Gray 7 Gray Blue Blue Red Module Connector Control Suspension 30 6 7 3 29 5 8 4 28 14 22 10 23 25 24 13 26 15 12 11 4 3 4 2 5 6 27 3 26 2 25 1 Conn 1 Conn 31 E-class (W207 / W212 2010+) CLS-class (W218 2012+) A I R M A T I C 32 E-class (W207 / W212 2010+) CLS-class (W218 2012+) A I R M A T I C

RIGHT FRONT LEFT FRONT LEFT REAR RIGHT REAR STEP-BY-STEP INSTALLATION to therearmost position CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR CAR HARNESSCONNECTOR...CAR on page44. Preparation Connector Refer to Vehicle‘s 21 the passenger‘s seat 25 REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM

13 5 1 9 Move 40 38

... AND INSERT ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN ... AND INSERT ITINTO... ANDINSERT 8-PIN

CONNECTOR CONNECTOR CONNECTOR CONNECTOR click! click! must click! click! 14 10 6 2 7 Disconnect thebattery Disconnect 1 6 2 Shell backview FemaleEmpty back view Female Shell back view Female Shell back view Female Shell 8 4 8 4 8 4 8 4 7 3 7 3 7 3 7 3 6 2 6 2 6 2 6 2 Vehicle‘s Battery 5 1 5 1 5 1 5 1 INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULE HARNESS 25 21 Brown Gray click! click! INSERT PINFROM INSERT PINFROM INSERT INSERT PINFROM INSERT INSERT PINFROM INSERT must click! 15 11 23 10 4 7 3 3 40 38 White Yellow click!

Remove themetalcover to expose theAirmatic Remove thefoormat and fold upthefoor control unit. 25 21 carpet. 4 3 CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY

16 12 8 4

Battery the Disconnect 40 38 23 10 BATTERY +12V BATTERY GND CANE - L CANE - H CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR screws and remove remove and screws the Suspension Suspension the REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM the cover Unscrew Unscrew Module Module L H + BATTERY 47 Green-White Green 25 21 17 29 33 - BATTERY 21 Switch (black button) button) (black Switch ... AND INSERT ITINTO... ANDINSERT 2-PIN ITINTO... ANDINSERT 2-PIN ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN Rotate the Function Function the Rotate + BATTERY - BATTERY to position 2 position to CONNECTOR CONNECTOR CONNECTOR CONNECTOR click! click! click! click! 30 26 22 18 34 2 1 8 4 Shell backview FemaleEmpty back view Female Shell back view Female Shell back view Female Shell 8 4 8 4 2 1 2 1 7 3 7 3 6 2 6 2 5 1 5 1

Ride Height Adjustment INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULEHARNESS BACK BACK Orange MALE MALE Green 2 1 2 1

VIEW VIEW

INSERT PINFROM INSERT PINFROM INSERT INSERT PINFROM INSERT INSERT PINFROM INSERT To continue, continue, To on page42 2 H 1 L go to to go click! click! 47 23 19 31 27 35 21 Red 8 4 click! click! Black BACK BACK 5 1 5 1 MALE MALE

6 2 6 2

VIEW VIEW 7 3 7 3

8 4 8 4

8 4 8 4 7 3 7 3 1) 1) 8 4 CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY 6 2 6 2 1) 1) 5 1 5 1 2 1 2) H L Red Black 2) MALE MALE 47 24 20 32 28 5 6 21

FRONT FRONT 2) 2) REMOTE REMOTE 2 1 2 1 14 22

VIEW VIEW MALE MALE

CONTROL CONTROL 33 E-class (W207 / W212 2010+) CLS-class (W218 2012+) A I R M A T I C 34 CL-class ( W216) S-class (W220 / W221) SL-class (R230 / R231) A B C Abc1

B22/7 Left Rear ABC (N51/2) Harness in thevehicle,ABC (N51/2)Harness Female Pin View 231 chassis 230 chassis 221 chassis 220 chassis 216 chassis Conn I Conn

B22/7 Left Rear 2

B22/10 Right Rear Rear RR LR

5 B22/10 Right Rear CL SL SL S S Battery ABC ABC ABC ABC ABC *NOTE: CANE L 2007 -2013 2000 -2006 2007 -2013 2003 -2012 2013+

Green H Green-White wires with electrical tape wires withelectrical Insulate each of these two Conn 3 Conn

L CANE-L

H CANE-H RF LF 48

24 48 +12 V B22/9 Right Front 23 47

22 46 Not Used* Not Used* Not Used Not Used 21

21 45 GND B22/8 Left Front 20

20 44 B22/8 Left Front Female Connector 19 43 8 pin Male pin View 42 18 42 Remote Remote

B22/9 Right Front Control 17 41 Back View Orange 2 1 5 3 2 6 1 7 8 4 Green 16 40 Black Red Pin View Pin Female Male 8 pin 15 39 10 11 12 13 1 2 3 4 5 6 7 8 9 14 38 14 15 16 17 18 19 20 21 22 23 24 25 26 13 37 16 12 36 11 35 5 1 10 34 16 33 9 6 2 32 8 Yellow Yellow Yellow Brown Brown Brown Green Green White White 7 3 Black 31 7 Gray Gray Blue Blue Red Module Connector Control Suspension 30 6 8 4 29 5 28 23 10 14 22 25 24 26 13 15 11 12 4 6 4 3 2 5 27 3 26 2 Conn M Conn 25 1 STEP-BY-STEP INSTALLATION 230 and 231 chassis: ABC active body control body 230 and231chassis:ABCactive 221 chassis: ABC (N51/2) active body control body 221 chassis:ABC(N51/2)active control body 220 chassis:ABC(N51/2)active control body 216 chassis:ABC(N51/2)active Shown on220S350 Interior, right front footwell upper Interior, right front footwell upper Engine compartment, left rear Engine compartment, left Interior, nearsteering column Battery the Disconnect 35 CL-class ( W216) S-class (W220 / W221) SL-class (R230 / R231) A B C 36 CL-class ( W216) S-class (W220 / W221) SL-class (R230 / R231) A B C

CANE - H RIGHT FRONT LEFT FRONT LEFT REAR RIGHT REAR 2 CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR CAR HARNESSCONNECTOR...CAR CAR HARNESSCONNECTOR...CAR CAR HARNESSCONNECTOR...CAR DISCONNECT THE BATTERY 5 REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM Vehicle‘s Battery on page44. Connector Preparation Refer to Vehicle‘s H Green-White 17 13 9 5 1 20 42 ... AND INSERT ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN ... AND INSERT ITINTO... ANDINSERT 8-PIN ... AND INSERT ITINTO... ANDINSERT 8-PIN CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR click! click! click! must click! 18 14 10 4 1 2 6 7 6 2 Shell backview FemaleEmpty back view Female Shell back view Female Shell back view Female Shell back view Female Shell 8 4 8 4 8 4 8 4 8 4 7 3 7 3 7 3 7 3 7 3 6 2 6 2 6 2 6 2 6 2 5 1 5 1 5 1 5 1 5 1 INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR LOWERING MODULEHARNESS LOWERING MODULE HARNESS LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULEHARNESS 2 Yellow Orange 5 White must click! click! INSERT PINFROM INSERT INSERT PINFROM INSERT PINFROM INSERT PINFROM INSERT INSERT PINFROM INSERT H 4 23 10 click! 19 15 3 11 3 7 4 20 42 Gray Brown click! BACK 5 1 MALE

6 2

8 4 2 8 4 5 7 3 23 10 4 CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY 6 2 1) 5 1 H MALE 20 16 12 6 4 8

FRONT 20 2) 42 REMOTE

CONTROL BATTERY +12V BATTERY GND CANE - L CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR screws and remove remove and screws the Suspension Suspension the REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM the cover Unscrew Unscrew Module Module BATTERY L

48 + Green 33 21 29 25 - BATTERY 21 Switch (black button) button) (black Switch ... AND INSERT ITINTO... ANDINSERT 2-PIN ITINTO... ANDINSERT 2-PIN ITINTO... ANDINSERT 8-PIN Rotate the Function Function the Rotate + BATTERY - BATTERY to position 2 position to CONNECTOR CONNECTOR CONNECTOR click! click! click! 34 30 26 22 2 1 8 Shell backview FemaleEmpty back view Female Shell back view Female Shell 8 4 2 1 2 1 7 3 6 2 5 1

Ride Height Adjustment INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULEHARNESS BACK BACK MALE MALE 2 1 Green 2 1

VIEW VIEW

INSERT PINFROM INSERT PINFROM INSERT INSERT PINFROM INSERT To continue, continue, To on page42 2 1 L 48 go to to go click! 35 27 23 31 21 Red 8 click! click! Black BACK 5 1 MALE

6 2

4 8

8 4 7 3 1) 1) 8 CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY 6 2 1) 5 1 1 2 2) L Black Red 2) MALE 48 28 24 32 5 21

FRONT 2) REMOTE 2 1 2 1 22 14

VIEW MALE MALE

CONTROL 37 CL-class ( W216) S-class (W220 / W221) SL-class (R230 / R231) A B C 38 CL-class (W215 2002-2006) A B C Abc2 B22/7 Left Rear ABC (N51/2) Harness in thevehicle,ABC (N51/2)Harness Female Pin View 215 chassis Conn 1 Conn

B22/7 Left Rear 2

B22/10 Right Rear Rear RR LR

5 B22/10 Right Rear CL Battery ABC *NOTE: CANC L 2002 -2006

wires with electrical tape wires withelectrical Insulate each of these two Green H Green-White Conn 3 Conn

L CAN L

H CAN H RF LF 48

24 48 +12 V B22/9 Right Front 23 47

22 46 Not Used* Not Used* Not Used Not Used 21

21 45 GND B22/8 Left Front 20

20 44 B22/8 Left Front Connector 19 43 8 pinConnector Female Male Female Male pin View 42 18 42 Remote Remote

B22/9 Right Front Control 17 41 Back View Orange 2 1 5 3 2 6 1 7 8 4 Green 16 40 Black Red Pin View Pin Female 15 39 10 11 12 13 1 2 3 4 5 6 7 8 9 14 38 14 15 16 17 18 19 20 21 22 23 24 25 26 13 37 16 12 36 11 35 5 1 10 34 16 33 9 6 2 32 8 Yellow Yellow Yellow Brown Brown Brown Green Green White White 7 3 Black 31 7 Gray Gray Blue Blue Red Module Connector Control Suspension 30 6 8 4 29 5 28 23 10 14 22 25 24 26 13 15 11 12 4 4 3 2 5 6 27 3 26 2 25 Conn 2 Conn 1 39 CL-class (W215 2002-2006) A B C 40 CL-class (W215 2002-2006) A B C

LEFT FRONT LEFT REAR RIGHT REAR STEP-BY-STEP INSTALLATION 2 CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR CAR HARNESSCONNECTOR...CAR 215 chassis: ABC (N51/2) active body control body 215 chassis:ABC(N51/2)active DISCONNECT THE BATTERY 5 REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM Vehicle‘s Battery on page44. Connector Preparation Refer to Vehicle‘s 9 5 1 20 ... AND INSERT ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN ... AND INSERT ITINTO... ANDINSERT 8-PIN CONNECTOR CONNECTOR CONNECTOR click! must click! 10 6 2 7 6 2 Shell backview FemaleEmpty back view Female Shell back view Female Shell 8 4 8 4 8 4 7 3 7 3 7 3 6 2 6 2 6 2 5 1 5 1 5 1 INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR INTO HARNESSCONNECTOR CAR LOWERING MODULEHARNESS LOWERING MODULEHARNESS LOWERING MODULE HARNESS 2 White 5 Yellow must click! click! INSERT PINFROM INSERT PINFROM INSERT INSERT PINFROM INSERT 3 10 Engine compartment, left rear Engine compartment, left 4 11 7 3 20 Gray

2 5 10 CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY 12 8 4 Battery the Disconnect 20 3 4 BATTERY +12V BATTERY GND CANC - L CANC - H RIGHT FRONT CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR HARNESSCONNECTOR...CAR CAR HARNESSCONNECTOR...CAR screws and remove remove and screws the Suspension Suspension the REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM REMOVE PINFROM the cover Unscrew Unscrew Module Module L BATTERY H

48 + Green-White Green 29 25 21 17 13 33 - BATTERY 21 42 Switch (black button) button) (black Switch ... AND INSERT ITINTO... ANDINSERT 2-PIN ITINTO... ANDINSERT 2-PIN ITINTO... ANDINSERT 8-PIN ITINTO... ANDINSERT 8-PIN ... AND INSERT ITINTO... ANDINSERT 8-PIN Rotate the Function Function the Rotate + BATTERY - BATTERY to position 2 position to CONNECTOR CONNECTOR CONNECTOR CONNECTOR CONNECTOR click! click! click! click! click! 30 26 22 18 14 34 2 1 8 4 1 Shell backview FemaleEmpty back view Female Shell back view Female Shell back view Female Shell back view Female Shell 8 4 8 4 8 4 2 1 2 1 7 3 7 3 7 3 6 2 6 2 6 2 5 1 5 1 5 1

VIEW VIEW

INSERT PINFROM INSERT INSERT PINFROM INSERT PINFROM INSERT INSERT PINFROM INSERT INSERT PINFROM INSERT To continue, continue, To on page42 2 H 1 L 48 go to to go 23 click! click! 19 31 27 23 15 35 21 Red 4 8 click! 42 click! Black Brown click! BACK BACK 5 1 5 1 MALE MALE

6 2 6 2

VIEW VIEW 7 3 7 3

8 4 4 8

8 4 8 4 7 3 7 3 1) 1) 23 4 8 CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY CHECK CONTINUITY 6 2 6 2 CHECK CONTINUITY 1) 1) 5 1 5 1 2 1 2) H L Red Black 2) MALE MALE 48 20 32 28 24 16 6 5 21

FRONT FRONT 2) 2) 42 REMOTE REMOTE 2 1 2 1 14 22

VIEW VIEW MALE MALE

CONTROL CONTROL 41 CL-class (W215 2002-2006) A B C 42 Ride Height Adjustment Ride Height Adjustment (do not start f (donotstart thenO On Press thebutton again Wait upto 20seconds. Cycle theignition key Adjustment Switches ). f button willturnO to lower thevehicle If stillnotsatisfed, If (button LEDonthe go backto step 8. (medium height). (gray buttons) Rotate allfour Wheel Height to position3 the engine). 10 4 1 7 Lowering cover. Module Adjust individual Wheel Replace theSuspension the moduleisinstalled! Plug intheSuspension Switches ifrequired Height Adjustment changing, perform parked onaneven Make sure you are Lowering Module. (to seetheheight Congratulations, Start theengine. Start the next step).the next surface. 11 2 8 5

Press the factory Press thefactory Vehicle Cycle the Vehicle Height check all Trouble Codes Reconnect thebattery.Reconnect Wait upto 20seconds Lowering will Module seconds in-between. (button then LEDOn until vehicle raises. We recommend to an axlealignment. ), withupto 20 f O in theSuspension (button LEDOn). Height button button again Green LEDs to perform to perform blink. and 12 3 9 6

0: lower by 1: lower by 2: lower by 3: lower by 4: lower by 5: lower by 6: lower by 7: lower by Wheel Height Adjustment Switch positions - - - NOTES: f (LEDs1,2,3,4stay On) O 4, 5,6,7=SuspensionModule On(LEDs1,2,3,4blink) 3 =SuspensionModule On(LED4isON,LEDs1,2,3blink) 2 =SuspensionModule On(LED4isON,LEDs1,2,3blink) 1 =SuspensionModule f (LEDs1,2,3,4stay On) O 0 =SuspensionModule Function Switch (seeinstallation instructions):

Left Front Adjustment Switch Left Rear AdjustmentLeft Rear Switch If aRemote ControlIf isbeingused, refer to theoperatinginitsusermanual. instructions and vehicle to vehicle: wheel to wheel from vary will approximationand an are valuesproceedinglowering The to intheStep-by-Step original position1or2,asdescribed Installation. back Switch Function the dealer,rotate the from back Once 0. position to button) (black Switch Function the rotating byRennTech the Module of Suspension turn to remember dealer,the to going Beforeprocedure. and equipment proper using dealer the at rected individual byrotatingadjustedthe ally Switches.Wheel Largerdifcor erencesbe should level. This is more noticeable when the vehicle is lowered. Small diferences can be manu is It quite common that even before the installation individual wheels are not at the same

2“ 1 3/4“ 1 1/2“ 1 3/8“ 1 1/8“ 1“ 3/4“ 3/8“

[30 mm] [25 mm] [20 mm] [10 mm] [50 mm] [45 mm] [40 mm] [35 mm] LED 2 LED 1 Right FrontRight Adjustment Switch Function Switch LED 3 LED 4 Right Rear Adjustment Rear Right Switch - - 43 Ride Height Adjustment Vehicle Connector Preparation DISCONNECTING the 26 pin connector from the lowering module

CONNECTING the 26 pin connector to the lowering module

30 pin and 48 pin Connector Dissasembly Remove cap by pushing and removing housing from plug by unlocking the two latches on the sides of the housing. Then slide header outward.

END CAP HEADER Plug Latch Latch Sliding HOUSING

EXTRACTING the pins from the housing Side Cap Dissasembly and re-assembly

To install: INSERT AND PUSH

To remove: To remove larger pins use extraction tools To remove small pins use extraction tools PUSH UPWARD HAZET 4662-4 HAZET 4669-4 + 4662-4 or a solid thin wire 44 Extracting and Inserting pins EXTRACTING the smaller pins from the housing

Use HAZET Tool No.: 4663-4 and Handle No.: 4669-4

EXTRACTING the larger pins from car connector

To Remove large pins use HAZET Tool No.: 4662-4 or a solid thin wire

INSERTING the pins back into the connector housing

In the 30 pin car connector use extraction tools HAZET 4669-4 and 4663-4 or a solid thin wire.

8 PIN FEMALE CONNECTOR

Insert header with wires into housing

To remove small pins use extraction tool HAZET 4669-4 or a solid thin wire.

45 46 Troubleshooting Troubleshooting Typical problems: GABOR: be deleted height limitexceeded2. Maximum for thecar-DTC generated, needsto rear goesuphigh,nocontrol 1. accidentally andrightsensorwires installation swapped during - left 47 Troubleshooting Warranty and Return Policy Suspension Control Module Warranty Policy ProgRama, Inc ofers a 30 day satisfaction guarantee on Suspension Control Module as well as a one year warranty against defects in materials or workmanship. ProgRama, Inc’s liability under this warranty shall be limited to the correction or replace- ment of any defective part or product in question which ProgRama, Incdetermines to be necessary. Warranty freight charges are the responsibility of the dealer, distributor and/or consumer. Excessive exposure to heat/sun, liquids and physical abuse will not be covered. The Suspension Control Module warranty is to the original purchaser and is non-transfe- rable. This warranty is void unless proof of purchase is submitted. Purchase price must be consis- tent with ProgRama, Inc’s Minimum Resale Price (MRP) pricing policy. Removal of serial numbers and/or alteration of product or packaging will void all warran- ties. ProgRama, Inc is not responsible for damages, including but not limited to improper installation, installation by a non-certifed technician, damages to the vehicle, loss of time and loss of proft resulting from installation or use of our product. In no event is our responsibility higher than the purchasing price paid for our product.

Return Policy ProgRama, Inc will not warranty, credit, or exchange any product returned without a valid Return Merchandise Authorization (RMA) number. All RMA numbers are issued by ProgRama, Inc RMA department. Defective units shall be repaired and returned in like kind. All units that must be refur- bished to like new condition are subject to labor and parts charges to be determined by ProgRama, Inc. All refunds for ProgRama, Inc products must be collected at original point of purchase - ProgRama, Inc will not credit dealers/customers that did not purchase products directly through ProgRama, Inc.

Governing Law and Venue This warranty shall be governed by and construed in accordance with the laws of United Stated, and venue for any legal proceeding or action at law arising out of or construing this Agreement shall lie in the courts of South Florida, and the parties specifcally waive any other venue.

48 Notes a a a a a a a a a a a a a a a a

a a a a a

LCM-V2 M-MIS-90312/2.0/20141229