( DIN 894 ) Open-End Slugging Wrench

Screwdrivers \ Open-end spanners and box wrenches

Single open-end wrench ( DIN 894 ) 15° jaw angle

Execution: Technical data: . Special steel . Jaw position: 15 Degree . Strong shank with double-T proﬁ le . Surface: Burnished . Material: Chrome-vanadium steel Advantage: . Sha proﬁ le creates excellent bending rigidity . Good force transfer . Non-slip feel

Width across fl ats 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm Length (mm) 75 80 95 100 105 110 125 130 Thickness (mm) 3.2 3.2 3.5 4 4.5 5 5 5.5 Ident. No. 006 007 008 009 010 011 012 013 52002... ● ● ● ● ● ● ● ● Width across fl ats 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm 22 mm 24 mm Length (mm) 140 145 155 160 160 170 195 215 Thickness (mm) 5.5 5.5 5.5 6 6 7 8 9 Ident. No. 014 015 016 017 018 019 022 024 52002... ● ● ● ● ● ● ● ● Width across fl ats 25 mm 27 mm 30 mm 32 mm 36 mm 38 mm 41 mm 46 mm Length (mm) 215 240 260 275 305 305 345 380 Thickness (mm) 9 10 11 12 13 13 14 15 Ident. No. 025 027 030 032 036 038 041 046 52002... ● ● ● ● ● ● ● ● Width across fl ats 50 mm 55 mm 60 mm 65 mm 70 mm 75 mm 80 mm 85 mm Length (mm) 415 460 495 530 575 610 645 690 Thickness (mm) 16 17 18 19 20 21 22 23 Ident. No. 050 055 060 065 070 075 080 085 52002... ● ● ● ● ● ● ● ● Width across fl ats 90 mm 95 mm 100 mm 105 mm 110 mm Length (mm) 740 740 800 850 900 Thickness (mm) 25 25 26 28 28 Ident. No. 090 095 100 105 110 52002... ● ● ● ● ● Prod. Gr. 526

Open-end slugging wrench ( DIN 133 ) 15° jaw angle

Application: . Short version for use in tight installation areas For tightening or loosening heavily seized screw . Heavy-duty with large force transmission connections using a hammer. . High-resistance steel Execution: Technical data: . Short shank with reinforced block end . Jaw position: 15 Degree . Surface: Bare Advantage: . Material: Chrome-vanadium steel . Suitable for heavy-duty assembly work

Width across ﬂ ats 27 mm 30 mm 32 mm 36 mm 41 mm 46 mm 50 mm 55 mm 60 mm 65 mm 70 mm 75 mm 80 mm 85 mm Length (mm) 180 190 195 210 225 255 280 315 320 350 370 400 405 405 Thickness (mm) 16.5 17 17.5 18.5 19.5 20 21.5 24.5 24.5 28 30 31.5 34.5 34.5 Ident. No. 027 030 032 036 041 046 050 055 060 065 070 075 080 085 52005... ● ● ● ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 530

Double open-end wrench ( DIN 3110 ) Jaw angle 15° at both ends

Technical data: . Material: Chrome-vanadium steel . Jaw position: 15 Degree . Surface: Chrome-plated

Width across fl ats 6 x 7 mm 8 x 9 mm 8 x 10 mm 10 x 11 mm 10 x 13 mm 11 x 13 mm 12 x 13 mm 12 x 14 mm Length (mm) 125 142 142 157 170 170 175 175 Ident. No. 500 530 540 570 590 595 600 610 52009... ● ● ● ● ● ● ● ● Width across fl ats 13 x 14 mm 13 x 15 mm 13 x 17 mm 14 x 15 mm 14 x 17 mm 16 x 17 mm 16 x 18 mm 17 x 19 mm Length (mm) 188 188 205 188 205 205 205 222 Ident. No. 620 630 640 650 660 670 675 680 52009... ● ● ● ● ● ● ● ● Width across fl ats 18 x 19 mm 19 x 22 mm 19 x 24 mm 20 x 22 mm 21 x 23 mm 22 x 24 mm 24 x 26 mm 24 x 27 mm Length (mm) 222 233 249 236 249 249 266 266 Ident. No. 690 700 705 710 715 740 750 760 52009... ● ● ● ● ● ● ● ● Width across fl ats 25 x 28 mm 27 x 30 mm 27 x 32 mm 30 x 32 mm 30 x 36 mm 32 x 36 mm 36 x 41 mm 41 x 46 mm Length (mm) 282 282 305 305 325 330 370 400 Ident. No. 765 770 775 810 820 830 840 845 52009... ● ● ● ● ● ● ● ● Prod. Gr. 5HB Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1221 Availability subject to country specific rules and regulations.

1221_EN_2018_KERN[21850704]-s.indd 1221 12/17/2018 3:35:23 PM Screwdrivers \ Open-end spanners and box wrenches

ARE YOU LOOKING FOR EVEN MORE BRANDS? WE HAVE WHAT IT TAKES.

For a complete range of products that meet the toughest demands, visit www.iconridge.com

Source: Hahn+Kolb Werkzeuge GmbH 1222Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1221_EN_2018_KERN[21850704]-s.indd 1222 12/17/2018 3:35:24 PM Screwdrivers \ Open-end spanners and box wrenches

Double open-end wrench ( DIN 895 ) Jaw angle 15° at both ends

Execution: . Non-slip feel . Special steel . Strong shank with double-T proﬁ le Technical data: . Jaw position: 15 Degree Advantage: . Material: Chrome-vanadium steel . Sha proﬁ le creates excellent bending rigidity . Surface: Burnished . Good force transfer

Width across fl ats 6 x 7 mm 7 x 8 mm 8 x 9 mm 8 x 10 mm 9 x 11 mm 10 x 11 mm 10 x 13 mm 11 x 13 mm Length (mm) 96 108 108 115 124 124 140 140 Thickness (mm) 3.3 4 4 4.5 5 5 5 5.5 Ident. No. 010 020 040 050 080 090 110 130 52008... ● ● ● ● ● ● ● ● Width across fl ats 12 x 13 mm 12 x 14 mm 13 x 14 mm 13 x 15 mm 13 x 17 mm 14 x 15 mm 14 x 17 mm 16 x 17 mm Length (mm) 140 140 140 155 160 155 160 160 Thickness (mm) 5.5 5.5 5.5 5.5 6 5.5 6 6 Ident. No. 150 160 170 180 190 195 200 205 52008... ● ● ● ● ● ● ● ● Width across fl ats 16 x 18 mm 17 x 19 mm 17 x 22 mm 18 x 19 mm 18 x 21 mm 19 x 22 mm 19 x 24 mm 20 x 22 mm Length (mm) 170 170 195 170 195 195 205 195 Thickness (mm) 6.5 7 8 7 8 8 9 8 Ident. No. 208 210 220 225 228 230 240 245 52008... ● ● ● ● ● ● ● ● Width across fl ats 21 x 23 mm 22 x 24 mm 22 x 27 mm 24 x 27 mm 24 x 30 mm 25 x 28 mm 27 x 30 mm 27 x 32 mm Length (mm) 220 220 235 245 270 245 275 275 Thickness (mm) 9 9 10 10 11 10 12 11 Ident. No. 247 250 260 270 280 285 290 300 52008... ● ● ● ● ● ● ● ● Width across fl ats 30 x 32 mm 30 x 36 mm 32 x 36 mm 36 x 41 mm 41 x 46 mm 46 x 50 mm 50 x 55 mm 55 x 60 mm Length (mm) 275 305 310 345 380 420 460 500 Thickness (mm) 12 13 14 14 15 16 17 18 Ident. No. 310 320 330 340 350 360 370 380 52008... ● ● ● ● ● ● ● ● Prod. Gr. 526

Double open-end wrench ( DIN 3110 ) Jaw angle 15° at both ends

. Jaw position: 15 Degree . Material: Chrome-vanadium steel . Surface: Chrome-plated Technical data:

Width across fl ats 4 x 4.5 mm 4 x 5 mm 5 x 5.5 mm 5.5 x 7 mm 6 x 7 mm 6 x 8 mm 7 x 8 mm 7 x 9 mm Length (mm) 100 100 100 122 122 122 140 140 Ident. No. 005 010 020 030 040 045 050 055 52012... ● ● ● ● ● ● ● ● Width across fl ats 8 x 9 mm 8 x 10 mm 9 x 10 mm 9 x 11 mm 10 x 11 mm 10 x 12 mm 10 x 13 mm 11 x 13 mm Length (mm) 140 140 157 157 157 157 172 172 Ident. No. 060 070 080 090 100 105 110 130 52012... ● ● ● ● ● ● ● ● Width across fl ats 11 x 14 mm 12 x 13 mm 12 x 14 mm 13 x 14 mm 13 x 15 mm 13 x 16 mm 13 x 17 mm 14 x 15 mm Length (mm) 172 172 172 178 188 190 205 188 Ident. No. 140 150 160 170 180 185 190 200 52012... ● ● ● ● ● ● ● ● Width across fl ats 14 x 17 mm 16 x 17 mm 16 x 18 mm 17 x 19 mm 17 x 22 mm 18 x 19 mm 18 x 21 mm 19 x 22 mm Length (mm) 205 205 205 222 236 222 236 236 Ident. No. 210 220 222 230 235 240 245 250 52012... ● ● ● ● ● ● ● ● Width across fl ats 19 x 24 mm 20 x 22 mm 21 x 23 mm 21 x 24 mm 22 x 24 mm 22 x 27 mm 24 x 26 mm 24 x 27 mm Length (mm) 250 236 247 250 250 266 266 266 Ident. No. 260 270 280 285 290 300 310 320 52012... ● ● ● ● ● ● ● ● Width across fl ats 24 x 30 mm 25 x 28 mm 27 x 29 mm 27 x 30 mm 27 x 32 mm 30 x 32 mm 30 x 34 mm 30 x 36 mm Length (mm) 280 280 302 302 302 302 302 328 Ident. No. 330 340 350 360 370 380 385 390 52012... ● ● ● ● ● ● ● ● Width across fl ats 32 x 36 mm 34 x 36 mm 36 x 41 mm 38 x 42 mm 41 x 46 mm 46 x 50 mm Length (mm) 328 328 360 360 400 450 Ident. No. 400 405 410 412 420 430 52012... ● ● ● ● ● ●

Prod. Gr. 530

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1223 Availability subject to country specific rules and regulations.

1221_EN_2018_KERN[21850704]-s.indd 1223 12/17/2018 3:35:25 PM Screwdrivers \ Open-end spanners and box wrenches

Double open-end wrench ( DIN 3110 ) Jaw angle 15° at both ends

. Jaw position: 15 Degree . Material: Steel, specially hardened . Surface: Chrome-plated Technical data:

Width across fl ats 4 x 5 mm 5.5 x 7 mm 6 x 7 mm 7 x 8 mm 8 x 9 mm 8 x 10 mm 10 x 11 mm 10 x 12 mm Length (mm) 100 120 120 140 140 140 155 170 Ident. No. 010 030 040 050 060 070 100 105 52013... ● ● ● ● ● ● ● ● Width across fl ats 10 x 13 mm 11 x 13 mm 12 x 13 mm 12 x 14 mm 13 x 14 mm 13 x 15 mm 13 x 17 mm 14 x 15 mm Length (mm) 170 170 170 170 190 190 205 190 Ident. No. 110 130 150 160 170 180 190 200 52013... ● ● ● ● ● ● ● ● Width across fl ats 14 x 17 mm 16 x 17 mm 16 x 18 mm 17 x 19 mm 18 x 19 mm 18 x 21 mm 19 x 22 mm 20 x 22 mm Length (mm) 205 205 220 220 220 235 235 235 Ident. No. 210 220 222 230 240 245 250 270 52013... ● ● ● ● ● ● ● ● Width across fl ats 21 x 23 mm 21 x 24 mm 22 x 24 mm 24 x 26 mm 24 x 27 mm 25 x 28 mm 27 x 30 mm 27 x 32 mm Length (mm) 250 250 250 270 280 285 300 300 Ident. No. 280 285 290 310 320 340 360 370 52013... ● ● ● ● ● ● ● ● Width across fl ats 30 x 32 mm 30 x 34 mm 32 x 36 mm 34 x 36 mm 36 x 41 mm 41 x 46 mm Length (mm) 300 300 325 325 375 425 Ident. No. 380 385 400 405 410 420 52013... ● ● ● ● ● ● Prod. Gr. 531

Double open-end wrench ( DIN 3110 ) Jaw angle 15° at both ends

. Jaw position: 15 Degree . Material: Chrome-vanadium steel . Surface: Chrome-plated Technical data:

Width across fl ats 6 x 7 mm 8 x 9 mm 8 x 10 mm 10 x 11 mm 10 x 13 mm 12 x 13 mm 13 x 15 mm 13 x 17 mm Length (mm) 125 142 140 157 172 173 188 205 Thickness (mm) 3.5 3.9 4.2 4.5 5.0 5.0 5.5 5.8 Ident. No. 040 060 070 105 110 150 180 190 52017... ● ● ● ● ● ● ● ● Width across fl ats 14 x 15 mm 16 x 17 mm 17 x 19 mm 18 x 19 mm 19 x 22 mm 20 x 22 mm 22 x 24 mm 24 x 27 mm Length (mm) 188 205 210 222 233 236 249 266 Thickness (mm) 5.5 6.0 6.5 6.5 7.0 7.0 7.8 8.0 Ident. No. 200 220 230 240 250 270 290 320 52017... ● ● ● ● ● ● ● ● Width across fl ats 30 x 32 mm Length (mm) 304 Thickness (mm) 9.0 Ident. No. 380 52017... ● Prod. Gr. 526

Source: Hahn+Kolb Werkzeuge GmbH 1224Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1221_EN_2018_KERN[21850704]-s.indd 1224 12/17/2018 3:35:27 PM Screwdrivers \ Open-end spanners and box wrenches

Double open-end wrench sets ( DIN 3110 ) Jaw angle 15° at both ends

Advantage: Technical data: . Range of the most common double open-end . Jaw position: 15 Degree wrenches to suit practical demands . Surface: Chrome-plated . Material: Chrome-vanadium steel

No. 52009 870

Width across ﬂ ats Number of pieces in assortment/set (PCS) 52009... 52017... Ident. No. Ident. No. 6 x 7 mm 8 x 9 mm 10 x 11 mm 12 x 13 mm 14 x 15 mm | | | | 8 850 ● 850 ● | 16 x 17 mm | 18 x 19 mm | 20 x 22 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm | 14 x 15 mm | 16 x 17 mm | 18 x 19 mm | 20 x 22 mm | 24 x 27 mm | 30 10 860 ● 860 ● x 32 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 10 x 13 mm | 12 x 13 mm | 14 x 15 mm | 16 x 17 mm | 17 x 19 mm | 18 x 19 mm | 20 x 12 870 ● 870 ● 22 mm | 24 x 27 mm | 30 x 32 mm a = Prod. Gr. 5HB ORION = Prod. Gr. 526

Double open-end wrench sets, metric and inch ( DIN 3110 ) Jaw angle 15° at both ends

Advantage: Technical data: . Range of the most common double open-end . Jaw position: 15 Degree wrenches to suit practical demands . Surface: Chrome-plated . Material: Chrome-vanadium steel Ident. No. 715 Width across ﬂ ats Number of pieces in assortment/set (PCS) 52012... Ident. No. 6 x 7 mm 8 x 9 mm 10 x 11 mm 12 x 13 mm 14 x 15 | | | | 8 700 ● mm | 16 x 17 mm | 18 x 19 mm | 20 x 22 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm | 14 x 15 mm | 16 x 17 mm | 18 x 19 mm | 20 x 22 mm | 21 x 23 12 710 ● mm | 24 x 27 mm | 25 x 28 mm | 30 x 32 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm | 14 x 15 mm | 16 x 17 mm | 18 x 19 mm | 20 x 22 mm | 21 x 23 12 715 ● mm | 24 x 26 mm | 25 x 28 mm | 27 x 32 mm Prod. Gr. 530

Double open-end wrench sets, metric and inch ( DIN 3110 ) Jaw angle 15° at both ends

Advantage: . Range of the most common double open-end wrenches to suit practical demands Technical data: . Jaw position: 15 Degree Delivery: . Surface: Chrome-plated Ident. No. 700–720: in fabric tool roll with Velcro . Material: Steel, specially hardened fastener

Width across ﬂ ats Number of pieces in 52013... assortment/set (PCS) Ident. No. 6 x 7 mm 8 x 9 mm 10 x 11 mm 12 x 13 mm 14 x 15 mm 16 x 17 Ident. No. 715 | | | | | 8 700 ● mm | 18 x 19 mm | 20 x 22 mm 6 x 7 mm 8 x 9 mm 10 x 11 mm 12 x 13 mm 14 x 15 mm 16 x 17 | | | | | 10 715 ● mm | 18 x 19 mm | 20 x 22 mm | 24 x 27 mm | 30 x 32 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm | 14 x 15 mm | 16 x 17 mm | 18 x 19 mm | 20 x 22 mm | 21 x 23 mm | 24 x 27 mm | 25 x 28 12 720 ● mm | 30 x 32 mm 1/4 x 5/16 inch 3/8 x 7/16 inch 1/2 x 9/16 inch 5/8 x 3/4 inch | | | | 7 800 ● 11/16 x 13/16 inch | 7/8 x 15/16 inch | 11/8 x 15/16 inch 1/4 x 5/16 inch | 3/8 x 7/16 inch | 1/2 x 9/16 inch | 9/16 x 5/8 inch | 19/32 x 11/16 inch | 5/8 x 3/4 inch | 11/16 x 13/16 inch | 3/4 x 11 810 ● 7/8 inch | 25/32 x 13/16 inch | 7/8 x 15/16 inch | 11/8 x 15/16 inch Ident. No. 800 Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1225 Availability subject to country specific rules and regulations.

1225_EN_2018_KERN[21850709]-p.indd 1225 12/17/2018 3:35:29 PM Screwdrivers \ Open-end spanners and box wrenches

Double open-end wrench sets ( DIN 3110 ) Jaw angle 15° at both ends

Advantage: . Range of the most common double open-end wrenches to suit practical demands Technical data: . Jaw position: 15 Degree Delivery: . Surface: Chrome-plated Ref. no. 820 and 840 in box, ref. no. 870 and 890 in . Material: Chrome-vanadium steel plastic clamp holder Ident. No. 840 Ident. No. 890

Width across ﬂ ats Number of pieces in assortment/set (PCS) 52015... Ident. No. 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm 14 x 15 mm 16 x 17 mm 18 x | | | 10 820 ● 19 mm | 21 x 22 mm | 24 x 26 mm | 27 x 32 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm 14 x 15 mm 16 x 17 mm 18 x | | | 12 840 ● 19 mm | 20 x 22 mm | 21 x 23 mm | 24 x 26 mm | 25 x 28 mm | 27 x 32 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm | 14 x 15 mm | 16 x 17 mm | 18 x 8 870 ● 19 mm | 21 x 22 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm 14 x 15 mm 16 x 17 mm 18 x | | | 12 890 ● 19 mm | 20 x 22 mm | 21 x 23 mm | 24 x 27 mm | 25 x 28 mm | 30 x 32 mm Prod. Gr. 569

ELECTRICIAN’S double open-end wrench Jaw angle 15° and 75°

Application: Advantage: For working in hard-to-reach places in the ﬁ elds of . Jaw angles from 15° and 75° enable use in electronics and precision mechanics. conﬁ ned installation areas

Execution: Technical data: . Double-sided with identical wrench sizes . Material: Steel, specially hardened . Handle with double-T proﬁ le . Surface: Chrome-plated . Polished heads Width across ﬂ ats 3.2 mm 3.5 mm 4 mm 4.5 mm 5 mm 5.5 mm 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm Length (mm) 70 70 70 70 78 78 78 91 96 103 105 116 116 131 131 Thickness (mm) 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 Ident. No. 010 020 030 040 050 060 070 080 090 100 110 120 130 140 150 52010... ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 531

ELEKTRIKER double open-end wrench sets Jaw angle 15° and 75°

Application: Advantage: For working in hard-to-reach places in the fi elds of . Jaw angles from 15° and 75° enable use in electronics and precision mechanics. confi ned installation areas . Range of various ELECTRICIAN’S double open-end Execution: wrenches with the most common wrench sizes to . Double-sided with identical wrench sizes suit practical demands Ident. No. 005 . Handle with double-T profi le . Polished heads Technical data: . Surface: Chrome-plated . Material: Steel, specially hardened

Width across ﬂ ats Number of pieces in assortment/set (PCS) 52011... Ident. No. 4 mm 4.5 mm 5 mm 5.5 mm 6 mm | | | | | 10 005 ● 7 mm | 8 mm | 9 mm | 10 mm | 11 mm 3.2 mm | 3.5 mm | 4 mm | 4.5 mm | 5 mm | 5.5 mm | 6 mm | 7 mm | 8 mm | 9 mm | 15 010 ● 10 mm | 11 mm | 12 mm | 13 mm | 14 mm Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH 1226Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1225_EN_2018_KERN[21850709]-p.indd 1226 12/17/2018 3:35:30 PM Screwdrivers \ Open-end spanners and box wrenches

Crowfoot open-end spanners and box wrenches

Application: . Ident. No. 310–336: Ring wrench head with For mounting on drive tools such as ratchets, exten- square socket drive sions etc. Advantage: Execution: . Makes it easier to work in hard-to-reach places . Drop-forged . Ident. No. 212–224: Open-end wrench head with Technical data: square socket drive . Surface: Chrome-plated . Material: Steel, specially hardened Ident. No. 212–224

Ident. No. 310–336

Width across fl ats 12 mm 13 mm 14 mm 15 mm 17 mm 19 mm 22 mm 24 mm Drive 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch Thickness (mm) 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 Ident. No. 212 213 214 215 217 219 222 224 52035... ● ● ● ● ● ● ● ● Width across fl ats 10 mm 12 mm 13 mm 14 mm 15 mm 16 mm 17 mm 18 mm Drive 1/4 inch 1/4 inch 1/4 inch 1/4 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch Thickness (mm) 13.5 14 14 14 17.5 17.5 17.5 18.5 Ident. No. 310 312 313 314 315 316 317 318 52035... ● ● ● ● ● ● ● ● Width across fl ats 19 mm 20 mm 21 mm 22 mm 24 mm 26 mm 27 mm 30 mm Drive 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 1/2 inch Thickness (mm) 18.5 18.5 18.5 19 19.5 20 21.4 22.5 Ident. No. 319 320 321 322 324 326 327 330 52035... ● ● ● ● ● ● ● ● Width across fl ats 32 mm 36 mm Drive 1/2 inch 1/2 inch Thickness (mm) 22.5 24 Ident. No. 332 336 52035... ● ● Prod. Gr. 531

Combination wrenches ( DIN 3113 ) Jaw angle 15°, ring side angled 15°

Advantage: Technical data: . Energy profi le increases the force application areas . Tip profi le type: ENERGY profi le for optimum load distribution . Jaw position: 15 Degree . Gentle on the bolt/nut and tool . Surface: Chrome-plated . Material: Chrome-vanadium steel . Even slightly damaged heads can still be screwed on

Width across fl ats 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm Length (mm) 100 110 120 130 140 150 160 170 Ident. No. 060 070 080 090 100 110 120 130 52034... ● ● ● ● ● ● ● ● Width across fl ats 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm 20 mm 21 mm Length (mm) 180 190 190 210 210 230 230 260 Ident. No. 140 150 160 170 180 190 200 210 52034... ● ● ● ● ● ● ● ● Width across fl ats 22 mm 24 mm 27 mm 30 mm 32 mm Length (mm) 260 280 310 340 360 Ident. No. 220 240 270 300 320 52034... ● ● ● ● ●

Prod. Gr. 5HB

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1227 Availability subject to country specific rules and regulations.

1225_EN_2018_KERN[21850709]-p.indd 1227 12/17/2018 3:35:31 PM Screwdrivers \ Open-end spanners and box wrenches

Combination wrenches ( DIN 3113 ) Jaw angle 15°, ring side angled 15°

Execution: Technical data: . ring side with UD profi le for gentle power . Tip profi le type: UD profi le transmission . Jaw position: 15 Degree . hollow sha for a secure grip . Surface: Chrome-plated . Material: Chrome-vanadium steel

Width across fl ats 3 mm 3.2 mm 3.5 mm 4 mm 4.5 mm 5 mm 5.5 mm 6 mm Length (mm) 78 78 78 78 85 92 92 100 Ident. No. 030 032 035 040 045 050 055 060 52032... ● ● ● ● ● ● ● ● Width across fl ats 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm Length (mm) 110 120 130 140 150 160 170 180 Ident. No. 070 080 090 100 110 120 130 140 52032... ● ● ● ● ● ● ● ● Width across fl ats 15 mm 16 mm 17 mm 18 mm 19 mm 20 mm 21 mm 22 mm Length (mm) 190 200 210 220 230 240 252 262 Ident. No. 150 160 170 180 190 200 210 220 52032... ● ● ● ● ● ● ● ● Width across fl ats 23 mm 24 mm 25 mm 26 mm 27 mm 28 mm 29 mm 30 mm Length (mm) 270 282 290 302 310 320 330 340 Ident. No. 230 240 250 260 270 280 290 300 52032... ● ● ● ● ● ● ● ● Width across fl ats 32 mm 34 mm 36 mm Length (mm) 370 420 490 Ident. No. 320 340 360 52032... ● ● ● Prod. Gr. 530

Combination wrenches ( DIN 3113 ) Jaw angle 15°, ring side angled 15°

Advantage: Technical data: . High force transmission to the edges of the bolts . Tip proﬁ le type: AS drive proﬁ le and nuts for optimum load distribution . Jaw position: 15 Degree . Increased bolt and nut service lives . Surface: Chrome-plated . Material: Steel, specially hardened

Width across fl ats 3.2 mm 3.5 mm 4 mm 4.5 mm 5 mm 5.5 mm 6 mm 7 mm Length (mm) 75 75 85 85 95 100 105 110 Ident. No. 032 035 040 045 050 055 060 070 52036... ● ● ● ● ● ● ● ● Width across fl ats 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm 15 mm Length (mm) 115 120 125 135 140 160 165 170 Ident. No. 080 090 100 110 120 130 140 150 52036... ● ● ● ● ● ● ● ● Width across fl ats 16 mm 17 mm 18 mm 19 mm 20 mm 21 mm 22 mm 23 mm Length (mm) 180 190 200 230 230 260 260 280 Ident. No. 160 170 180 190 200 210 220 230 52036... ● ● ● ● ● ● ● ● Width across fl ats 24 mm 25 mm 26 mm 27 mm 28 mm 29 mm 30 mm 32 mm Length (mm) 280 300 300 300 320 330 330 360 Ident. No. 240 250 260 270 280 290 300 320 52036... ● ● ● ● ● ● ● ● Width across fl ats 34 mm 36 mm 38 mm 41 mm 46 mm 50 mm 55 mm 60 mm Length (mm) 450 460 480 480 500 530 560 590 Ident. No. 340 360 380 410 460 500 550 600 52036... ● ● ● ● ● ● ● ● Prod. Gr. 531

Combination wrenches ( DIN 3113 ) Jaw angle 15°, ring side angled 15°

Execution: Technical data: . Traction profi le on ring side . Tip profi le type: Tractions profi le . Jaw position: 15 Degree Advantage: . Surface: Chrome-plated . Slim heads . Material: Chrome-vanadium steel

Source: Hahn+Kolb Werkzeuge GmbH 1228Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1225_EN_2018_KERN[21850709]-p.indd 1228 12/17/2018 3:35:34 PM Screwdrivers \ Open-end spanners and box wrenches

Width across fl ats 5.5 mm 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm Length (mm) 105 105 119 130 143 155 169 181 Ident. No. 200 210 220 230 240 250 260 270 52038... ● ● ● ● ● ● ● ● Width across fl ats 13 mm 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm 20 mm Length (mm) 193 205 218 231 243 255 269 280 Ident. No. 280 290 300 310 320 330 340 350 52038... ● ● ● ● ● ● ● ● Width across fl ats 21 mm 22 mm 23 mm 24 mm 25 mm 26 mm 27 mm 28 mm Length (mm) 292 305 328 328 354 354 380 380 Ident. No. 360 370 380 390 400 410 420 430 52038... ● ● ● ● ● ● ● ● Width across fl ats 29 mm 30 mm 32 mm 34 mm 36 mm 41 mm Length (mm) 380 406 420 432 460 500 Ident. No. 440 450 460 470 480 490 52038... ● ● ● ● ● ● Prod. Gr. 569

Combination wrenches ( DIN 3113 ) Jaw angle 15°, ring side angled 15°

Technical data: . Surface: Chrome-plated . Tip proﬁ le type: Standard proﬁ le . Material: Chrome-vanadium steel . Jaw position: 15 Degree

Width across fl ats 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm Length (mm) 100 110 120 130 140 150 160 170 Ident. No. 060 070 080 090 100 110 120 130 52037... ● ● ● ● ● ● ● ● Width across fl ats 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm 20 mm 22 mm Length (mm) 180 190 190 210 210 230 230 260 Ident. No. 140 150 160 170 180 190 200 220 52037... ● ● ● ● ● ● ● ● Width across fl ats 24 mm 27 mm 30 mm 32 mm Length (mm) 280 310 340 360 Ident. No. 240 270 300 320 52037... ● ● ● ● Prod. Gr. 526

Combination wrench sets, metric ( DIN 3113 ) Jaw angle 15°, ring side angled 15°

Advantage: Technical data: . Practical range of various combination wrenches . Jaw position: 15 Degree with the most common wrench sizes . Tip proﬁ le type: ENERGY proﬁ le . Surface: Chrome-plated . Material: Chrome-vanadium steel

No. 52034 684

Width across ﬂ ats Number of pieces in assortment/set (PCS) 52034... 52037... Ident. No. Ident. No. 8 mm | 9 mm | 10 mm | 11 mm | 13 mm | 14 mm | 17 mm | 8 ● ● 19 mm 670 670 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 | | | | | | | 12 680 ● 680 ● mm | 14 mm | 17 mm | 19 mm | 22 mm 10 mm 11 mm 12 mm 13 mm 14 mm 17 mm 19 mm | | | | | | 12 684 ● 684 ● | 22 mm | 24 mm | 27 mm | 30 mm | 32 mm 6 mm | 7 mm | 8 mm | 9 mm | 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 18 mm | 19 mm | 17 690 ● 690 ● 20 mm | 22 mm | 24 mm a = Prod. Gr. 5HB ORION = Prod. Gr. 526

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1229 Availability subject to country specific rules and regulations.

1225_EN_2018_KERN[21850709]-p.indd 1229 12/17/2018 3:35:37 PM Screwdrivers \ Open-end spanners and box wrenches

Combination wrench sets, metric ( DIN 3113 ) Jaw angle 15°, ring side angled 15°

Execution: Technical data: . ring side with UD profi le for gentle power . Jaw position: 15 Degree transmission . Tip profi le type: UD profi le . hollow sha for a secure grip . Surface: Chrome-plated . Material: Chrome-vanadium steel Ident. No. 410 Width across fl ats Number of pieces in assortment/set (PCS) 52032... Ident. No. 10 mm 12 mm 13 mm 14 mm 17 mm | | | | 8 400 ● | 19 mm | 22 mm | 24 mm 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 17 mm | 19 mm | 22 mm | 24 mm | 27 12 410 ● mm | 30 mm | 32 mm 6 mm | 7 mm | 8 mm | 9 mm | 10 mm | 11 mm 12 mm 13 mm 14 mm 15 mm | | | | | 17 420 ● 16 mm | 17 mm | 18 mm | 19 mm | 20 mm | 21 mm | 22 mm Prod. Gr. 530

Combination wrench set XL, extra long ( DIN 3113 ) wrench types 52032610-632

Execution: . Width across fl ats: 10 mm | 11 mm | 12 mm | 13 . Ring side with UD profi le for gentle power mm | 14 mm | 17 mm | 19 mm | 22 mm | 24 mm transmission | 27 mm | 30 mm | 32 mm . Hollow sha for a secure grip . Number of pieces in assortment/set: 12 PCS . Extra long for increased torque . Jaw position: 15 Degree . Tip profi le type: UD profi le . Surface: Chrome-plated Technical data: . Material: Chrome-vanadium steel 700 52032... Ident. No. ● Prod. Gr. 530

Combination wrench sets, metric and inch ( DIN 3113 )

Execution: . Type AK Technical data: Advantage: . Jaw position: 15 Degree . Practical range of various combination wrenches . Tip proﬁ le type: AS drive proﬁ le with the most common wrench sizes . Surface: Chrome-plated . Material: Steel, specially hardened Delivery: In fabric tool roll with Velcro fastener, ref. no. 800 and 810 in box Ident. No. 710

Width across ﬂ ats Number of pieces in assortment/set (PCS) 52036... Ident. No. 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm 15 mm | | | | | | | | 11 700 ● 17 mm | 19 mm 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 17 | | | | | | | | 15 710 ● mm | 19 mm | 22 mm | 24 mm | 27 mm | 30 mm | 32 mm 6 mm | 7 mm | 8 mm | 9 mm | 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 18 mm | 19 mm | 20 mm | 21 mm | 17 720 ● 22 mm 7/16 inch 1/2 inch 9/16 inch 5/8 inch 11/16 inch 3/4 inch | | | | | | 8 800 ● 13/16 inch | 7/8 inch 1/4 inch | 9/32 inch | 5/16 inch | 11/32 inch | 3/8 inch | 7/16 inch | 1/2 inch 9/16 inch 19/32 inch 5/8 inch 11/16 inch 3/4 inch | | | | | | 20 810 ● 25/32 inch | 13/16 inch | 7/8 inch | 15/16 inch | 1 inch | 1 1/16 inch | 1 1/8 inch | 1 1/4 inch Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH 1230Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1230_EN_2018_KERN[21850716]-v.indd 1230 12/17/2018 3:35:35 PM Screwdrivers \ Open-end spanners and box wrenches

Combination wrench sets, metric ( DIN 3113 )

Advantage: Technical data: . Practical range of various combination wrenches . Jaw position: 15 Degree with the most common wrench sizes . Tip proﬁ le type: Tractions proﬁ le . Surface: Chrome-plated Delivery: . Material: Chrome-vanadium steel Supplied in boxes

Width across ﬂ ats Number of pieces in assortment/set (PCS) 52038... Ident. No. 7 mm | 8 mm | 9 mm | 10 mm | 11 mm | Ident. No. 820 12 mm 13 mm 14 mm 15 mm 16 mm | | | | 17 820 ● | 17 mm | 18 mm | 19 mm | 21 mm | 22 mm | 24 mm | 27 mm 6 mm | 7 mm | 8 mm | 9 mm | 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 18 mm | 19 mm | 21 mm 21 830 ● | 22 mm | 24 mm | 27 mm | 30 mm | 32 mm | 34 mm 5.5 mm | 6 mm | 7 mm | 8 mm | 9 mm | 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 18 mm | 19 mm | 20 mm | 21 mm | 22 mm | 23 mm | 30 840 ● 24 mm | 25 mm | 26 mm | 27 mm | 28 mm | 29 mm | 30 mm | 32 mm | 34 mm | 36 mm | 41 mm Prod. Gr. 569

Combination wrench ( DIN 3113 ) 15° jaw angle, low oﬀ set ring side

Width across fl ats 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm Length (mm) 100 115 125 140 145 160 165 180 Ident. No. 006 007 008 009 010 011 012 013 52039... ● ● ● ● ● ● ● ● Width across fl ats 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm 20 mm 21 mm Length (mm) 190 210 220 230 245 260 270 280 Ident. No. 014 015 016 017 018 019 020 021 52039... ● ● ● ● ● ● ● ● Width across fl ats 22 mm 24 mm 27 mm 30 mm 32 mm 36 mm Length (mm) 290 320 350 390 410 430 Ident. No. 022 024 027 030 032 036 52039... ● ● ● ● ● ● Prod. Gr. 5HB

Combination wrench ( DIN 3113 ) 15° jaw angle, low oﬀ set ring side

Width across fl ats 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm Length (mm) 125 135 145 155 165 180 180 195 Ident. No. 605 610 615 620 625 630 635 640 52039... ● ● ● ● ● ● ● ● Width across fl ats 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm 20 mm 21 mm Length (mm) 210 215 230 240 255 265 280 280 Ident. No. 645 650 655 660 665 670 675 680 52039... ● ● ● ● ● ● ● ● Width across fl ats 22 mm 24 mm 27 mm 30 mm 32 mm 34 mm 36 mm 41 mm Length (mm) 300 330 385 415 430 460 480 560 Ident. No. 685 695 710 720 725 728 730 735 52039... ● ● ● ● ● ● ● ● Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1231 Availability subject to country specific rules and regulations.

1230_EN_2018_KERN[21850716]-v.indd 1231 12/17/2018 3:35:36 PM Screwdrivers \ Open-end spanners and box wrenches

Combination wrench ( DIN 3113 ) 15° jaw angle, low oﬀ set ring side

Advantage: Technical data: . No pinching of edges on bolts and nuts due to . Tip proﬁ le type: UD proﬁ le force application on sides with optimum load . Jaw position: 15 Degree distribution . Surface: Chrome-plated . Material: Chrome-vanadium steel

Width across fl ats 5 mm 5.5 mm 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm Length (mm) 100 100 100 112 125 138 148 158 Ident. No. 550 555 560 570 580 590 600 610 52042... ● ● ● ● ● ● ● ● Width across fl ats 12 mm 13 mm 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm Length (mm) 168 185 198 210 220 232 245 258 Ident. No. 620 630 640 650 660 670 680 690 52042... ● ● ● ● ● ● ● ● Width across fl ats 20 mm 21 mm 22 mm 23 mm 24 mm 25 mm 26 mm 27 mm Length (mm) 270 280 292 305 318 328 340 352 Ident. No. 700 710 720 730 740 750 760 770 52042... ● ● ● ● ● ● ● ● Width across fl ats 28 mm 29 mm 30 mm 32 mm 34 mm 36 mm 41 mm 46 mm Length (mm) 370 370 390 412 412 460 520 550 Ident. No. 780 790 800 820 840 860 880 890 52042... ● ● ● ● ● ● ● ● Width across fl ats 50 mm 55 mm 60 mm Length (mm) 580 620 660 Ident. No. 900 910 920 52042... ● ● ● Prod. Gr. 530

Combination wrench sets, metric ( DIN 3113 ) 15° jaw angle, ring side ﬂ at depressed centre

Width across ﬂ ats Number of pieces in assortment/set (PCS) 52039... Ident. No. 8 mm | 9 mm | 10 mm | 11 mm | 13 mm | 8 ● 14 mm 17 mm 19 mm 500 | | Ident. No. 520 6 mm | 7 mm | 8 mm | 9 mm | 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 17 mm | 12 510 ● 19 mm | 22 mm 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 17 mm | 19 mm | 22 mm | 24 mm | 27 12 520 ● mm | 30 mm | 32 mm Prod. Gr. 5HB

Combination wrench sets, metric ( DIN 3113 ) 15° jaw angle, ring side ﬂ at depressed centre

Advantage: Technical data: . Practical range of various combination wrenches . Jaw position: 15 Degree with the most common wrench sizes . Tip proﬁ le type: AS drive proﬁ le . Surface: Chrome-plated Delivery: . Material: Steel, specially hardened in fabric tool roll with Velcro fastener

Width across ﬂ ats Number of pieces in assortment/set (PCS) 52039... Ident. No. 8 mm | 9 mm | 10 mm | 11 mm | 12 mm Ident. No. 810 | 13 mm | 14 mm | 15 mm | 17 mm | 19 11 800 ● mm | 22 mm 6 mm | 7 mm | 8 mm | 9 mm | 10 mm | 11 mm | 12 mm | 13 mm | 17 mm | 19 mm | 15 810 ● 22 mm | 24 mm | 27 mm | 30 mm | 32 mm 6 mm | 7 mm | 8 mm | 9 mm | 10 mm | 11 mm 12 mm 13 mm 14 mm 15 mm | | | | | 17 820 ● 16 mm | 17 mm | 18 mm | 19 mm | 20 mm | 21 mm | 22 mm Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH 1232Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1232_EN_2018_KERN[21850719]-t.indd 1232 12/17/2018 3:35:35 PM Screwdrivers \ Open-end spanners and box wrenches

Combination wrench sets, metric ( DIN 3113 ) Chromium-vanadium steel, jaw angle 15°, ring side ﬂ at depressed centre

Advantage: Technical data: . Practical range of various combination wrenches . Number of pieces in assortment/set: 17 PCS with the most common wrench sizes . Jaw position: 15 Degree . Tip proﬁ le type: Tractions proﬁ le Delivery: . Surface: Chrome-plated Ref. no. 820 in box, ref. no. 830 in holder . Material: Chrome-vanadium steel

Width across ﬂ ats 52040... Ident. No. 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm 15 mm 16 mm | | | | | | | | | | 820 ● 17 mm | 18 mm | 19 mm | 21 mm | 22 mm | 24 mm | 27 mm 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm 15 mm 16 | | | | | | | | | | 830 ● Ident. No. 830 mm | 17 mm | 18 mm | 19 mm | 21 mm | 22 mm | 24 mm Prod. Gr. 569

Combination wrench sets, metric ( DIN 3113 ) 15° jaw angle, ring side ﬂ at depressed centre

Advantage: Technical data: . Practical range of various combination wrenches . Jaw position: 15 Degree with the most common wrench sizes . Tip proﬁ le type: UD proﬁ le . Surface: Chrome-plated Delivery: . Material: Chrome-vanadium steel Ident. No. 035 Packed in a box

Width across ﬂ ats Number of pieces in assortment/set (PCS) 52043... Ident. No. 10 mm 12 mm 13 mm 14 mm 17 mm | | | | 8 020 ● | 19 mm | 22 mm | 24 mm 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 17 mm | 19 mm | 22 mm | 24 mm | 27 12 035 ● mm | 30 mm | 32 mm 6 mm | 7 mm | 8 mm | 9 mm | 10 mm | 11 mm 12 mm 13 mm 14 mm 15 mm | | | | | 17 045 ● 16 mm | 17 mm | 18 mm | 19 mm | 20 mm | 21 mm | 22 mm Prod. Gr. 530

JOKER combination ratchet wrench set

Execution: Advantage: . Made from chrome-molybdenum steel . Excellent rigidity and torque transfer thanks to . Nickel/chrome coating cutting geometry . Ratchet mechanism on the ring side . Bi-hexagonal shape for positive force transfer . Finely serrated ring ratchet with 80 teeth . clamping function for secure clamping of nuts and bolts . Jaw side with clamping function and bi-hexagonal Ident. No. 510 shape . end stop reduces risk of slipping . Jaw return angle of 30° . Nickel/chrome coating protects against corrosion Delivery: In robust tool roll

Composition of set Width across ﬂ ats Number of Surface Material 52040... pieces in assort- Ident. No. ment/set (PCS) Supplied lengths: Chrome ● 159-246 mm 10 mm | 13 mm | 17 mm | 19 mm 4 Chrome-plated molybdenum 500 lengths supplied: 8 mm | 10 mm | 11 mm | 12 mm | Chrome ● 144-246 mm 13 mm | 14 mm | 15 mm | 16 mm | 11 Chrome-plated molybdenum 510 17 mm | 18 mm | 19 mm Prod. Gr. 542

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1233 Availability subject to country specific rules and regulations.

1232_EN_2018_KERN[21850719]-t.indd 1233 12/17/2018 3:35:38 PM Screwdrivers \ Open-end spanners and box wrenches

JOKER Switch combination ratchet wrench set With angled, reversible ratchet head

Execution: Advantage: . Made from chrome-molybdenum steel . Excellent rigidity and torque transfer thanks to . Nickel/chrome coating cutting geometry . Switchable ratchet mechanism on the ring side . Bi-hexagonal shape for positive force transfer . Finely serrated ring ratchet with 80 teeth . clamping function for secure clamping of nuts and . Jaw side with clamping function and bi-hexagonal bolts shape . end stop reduces risk of slipping . Maul return angle of 30°, ring side 15° angled . Nickel/chrome coating protects against corrosion Ident. No. 600 Delivery: In robust tool roll Composition Width across Number of Surface Material 52040... of set ﬂ ats pieces in assort- Ident. No. ment/set (PCS) lengths supplied: 10 mm | 13 Chrome 159-246 mm mm | 17 mm | 4 Chrome-plated molybdenum 600 ● 19 mm 8 mm | 10 mm | 11 mm | 12 mm | 13 mm | lengths supplied: Chrome ● 144-246 mm 14 mm | 15 mm 11 Chrome-plated molybdenum 610 | 16 mm | 17 mm | 18 mm | 19 mm Prod. Gr. 542

Double ring ratchet wrench, 4 in 1

Execution: Advantage: . Straight shape . The four most common wrench sizes in a single . Switchable ratchet function tool

Width across ﬂ ats 10 mm | 13 mm | 17 mm | 19 mm Length (mm) 210 Surface Chrome-plated Material Chrome-vanadium steel Ident. No. 100 52043... ● Prod. Gr. 586

Four-way ratchet box wrench set

Execution: . Matt . Forged Advantage: . Anti-clockwise/clockwise rotation using reversing . Gentle dynamic drive profi le for longer service life lever of nuts and bolts . 5° return angle . Nickel-plated and chrome-plated Delivery: In textile pouch Composition of set Supplied lengths: 151 - 230 mm 8 mm | 9 mm | 10 mm | 11 mm | 12 mm | Width across fl ats 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 18 mm | 19 mm Number of pieces in assortment/set (PCS) 3 Tip profi le type Dynamic Drive profi le Surface Chrome-plated Material Chrome-vanadium steel Ident. No. 500 52043... ● Prod. Gr. 519

Ratchet combination spanner straight version

Execution: . Finely serrated ratchet on ring side with 72 teeth Technical data: . 5° return angle . Surface: Chrome-plated Advantage: . Material: Chrome-vanadium steel . 5° switching angle enables working in the most conﬁ ned spaces

Source: Hahn+Kolb Werkzeuge GmbH 1234Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1234_EN_2018_KERN[21850722]-y.indd 1234 12/17/2018 3:35:37 PM Screwdrivers \ Open-end spanners and box wrenches

Width across fl ats 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm 15 mm Length (mm) 136 143 160 168 174 180 193 200 Ident. No. 108 109 110 111 112 113 114 115 52044... ● ● ● ● ● ● ● ● Width across fl ats 16 mm 17 mm 18 mm 19 mm 21 mm 22 mm 24 mm 27 mm Length (mm) 216 233 239 250 285 285 325 359 Ident. No. 116 117 118 119 121 122 124 127 52044... ● ● ● ● ● ● ● ● Width across fl ats 30 mm 32 mm Length (mm) 425 425 Ident. No. 130 132 52044... ● ● Prod. Gr. 5HB

THE HIGHEST QUALITY PRODUCTS FOR MAXIMUM EFFICIENCY. WE HAVE WHAT IT TAKES.

For a complete range of products that meet the toughest demands, visit www.iconridge.com

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1235 Availability subject to country specific rules and regulations.

1234_EN_2018_KERN[21850722]-y.indd 1235 12/17/2018 3:35:37 PM Screwdrivers \ Open-end spanners and box wrenches

Ratchet combination spanner set straight version

Execution: Advantage: . Finely serrated ratchet on ring side with 72 teeth . 5° switching angle enables working in the most . 5° return angle conﬁ ned spaces Delivery: In roll-up pouch

Width across ﬂ ats 8 mm | 10 mm | 13 mm | 17 mm | 19 mm Number of pieces in assortment/set (PCS) 5 Surface Chrome-plated Material Chrome-vanadium steel Ident. No. 200 52044... ● Prod. Gr. 5HB

Ratchet combination spanner Reversible

Execution: Advantage: . Finely serrated ratchet on ring side with 72 teeth . 15° angled oﬀ set for better access in tight instal- . 5° switching angle lation spaces . Ring side angled 15° Technical data: . Surface: Chrome-plated . Material: Chrome-vanadium steel

Width across ﬂ ats 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm Length (mm) 140 150 159 165 172 178 191 200 208 226 237 248 Ident. No. 208 209 210 211 212 213 214 215 216 217 218 219 52044... ● ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 5HB

Ratchet combination spanner set Reversible

Width across ﬂ ats 8 mm | 10 mm | 13 mm | 17 mm | 19 mm Number of pieces in assortment/set (PCS) 5 Surface Chrome-plated Material Chrome-vanadium steel Ident. No. 300 52044... ● Prod. Gr. 5HB

Ratchet combination spanner With movable swivel head

Execution: . Finely serrated ratchet on ring side with 72 teeth . Technical data: 5° switching angle . Surface: Chrome-plated Advantage: . Material: Chrome-vanadium steel . Flexible applications and access in tight installation spaces thanks to movable swivel head

Width across ﬂ ats 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm Length (mm) 136 143 160 168 174 180 193 200 216 233 239 250 Ident. No. 308 309 310 311 312 313 314 315 316 317 318 319 52044... ● ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 5HB

Source: Hahn+Kolb Werkzeuge GmbH 1236Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1234_EN_2018_KERN[21850722]-y.indd 1236 12/17/2018 3:35:39 PM Screwdrivers \ Open-end spanners and box wrenches

Ratchet combination spanner set Movable ﬂ ex head

Execution: Advantage: . Finely serrated ratchet on ring side with 72 teeth . Flexible applications and access in tight installation . 5° switching angle spaces thanks to movable swivel head Delivery: In roll-up pouch

Width across ﬂ ats 8 mm | 10 mm | 13 mm | 17 mm | 19 mm Number of pieces in assortment/set (PCS) 5 Surface Chrome-plated Material Chrome-vanadium steel Ident. No. 400 52044... ● Prod. Gr. 5HB Wrench adapter for combination ratchet spanner

Execution: Advantage: . Ident. No. 410–415: Suitable for wrenches no. . Wrench is used as ﬁ ne-pitch drive ratchet for 52044 110 and 310 various applications . Ident. No. 420: Suitable for wrenches no. 52044 113 and 313 Technical data: . Ident. No. 430: Suitable for wrenches no. 52044 . Surface: Chrome-plated 119 and 319 . Material: Chrome-vanadium steel Ident. No. 410 Suitable for width Ident. No. 420 across ﬂ ats For 1/4” bits, 10 mm Ident. No. 410 52044... hexagon ● For 1/4” nuts, square 10 mm Ident. No. 415 52044... ● For 3/8” nuts, square 13 mm Ident. No. 420 52044... ● For 1/2” nuts, square 19 mm Ident. No. 430 52044... ● Prod. Gr. 5HB Combination ratchet spanner Ratchet function on both sides

Application: Advantage: For screw connections in inaccessible places with . Tight switching angle thanks to fi ne toothing optimum fl exibility. . Maximum fl exibility off ered by two-sided ratchet function Execution: . Finely serrated ratchet on ring side with 72 teeth Technical data: . Jaw-side ratchet function via sprung insert and . Surface: Chrome-plated special jaw shape . Material: Chrome-vanadium steel

Head detail

Width across ﬂ ats 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm 21 mm 22 mm 24 mm Length (mm) 140 149 158 165 171 178 190 199 208 225 236 247 289 289 322 Ident. No. 508 509 510 511 512 513 514 515 516 517 518 519 521 522 524 52044... ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 5HB

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1237 Availability subject to country specific rules and regulations.

1237_EN_2018_KERN[21850726]-u.indd 1237 12/17/2018 3:35:36 PM Screwdrivers \ Open-end spanners and box wrenches

Combination ratchet spanner set Ratchet function on both sides

Application: . Jaw-side ratchet function via sprung insert and For screw connections in inaccessible places with special jaw shape optimum fl exibility Advantage: Execution: . Tight switching angle thanks to fi ne toothing . Finely serrated ratchet on ring side with 72 teeth . Maximum fl exibility off ered by two-sided ratchet function

Width across ﬂ ats 8 mm | 10 mm | 13 mm | 17 mm | 19 mm Number of pieces in assortment/set (PCS) 5 Surface Chrome-plated Material Chrome-vanadium steel Ident. No. 600 52044... ● Prod. Gr. 5HB Open-end wrench with ring ratchet straight version

Application: . Sha profi le creates excellent bending rigidity For loosening or quickly tightening bolts and nuts . Longer service lives thanks to manganese phos- using a ratchet. phate-plated catches and pawls . No edges pinched thanks to UD profi le Execution: . Flat Technical data: . 7° return angle . Tip profi le type: UD profi le . Hollow section in shank with double T shape . Surface: Chrome-plated . Material: Chrome-vanadium steel Advantage: . Good grip thanks to shaped design Width across fl ats 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm 15 mm Length (mm) 140 150 160 164 170 180 190 200 Ident. No. 108 109 110 111 112 113 114 115 52046... ● ● ● ● ● ● ● ● Width across fl ats 16 mm 17 mm 18 mm 19 mm 21 mm 22 mm 24 mm 27 mm Length (mm) 212 225 237 250 274 292 325 359 Ident. No. 116 117 118 119 121 122 124 127 52046... ● ● ● ● ● ● ● ● Width across fl ats 30 mm 32 mm 34 mm 36 mm Length (mm) 399 424 449 480 Ident. No. 130 132 134 136 52046... ● ● ● ● Prod. Gr. 530 Open end spanners with ring ratchet - sets Straight version

Width across ﬂ ats Number of pieces in assortment/set (PCS) 52046... Ident. No. 8 mm | 9 mm | 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 15 mm | 16 mm | 17 mm 12 300 ● | 18 mm | 19 mm 8 mm | 10 mm | 13 mm | 17 mm | 19 mm 5 350 ● Prod. Gr. 530

Source: Hahn+Kolb Werkzeuge GmbH 1238Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1237_EN_2018_KERN[21850726]-u.indd 1238 12/17/2018 3:35:38 PM Screwdrivers \ Open-end spanners and box wrenches

Open-end spanners with ring ratchet Reversible design, angled ring side

Application: Advantage: For loosening or quickly tightening bolts and nuts . Good grip thanks to shaped design using a ratchet. . Sha profi le creates excellent bending rigidity Execution: . Longer service lives thanks to manganese phosphate-plated catches and pawls . 7° return angle . No edges pinched thanks to UD profi le . Anti-clockwise/clockwise rotation using reversing lever Technical data: . Hollow section in shank with double T shape . Tip profi le type: UD profi le . Ring side angled 13° with reversing lever . Surface: Chrome-plated . Material: Chrome-vanadium steel

Width across ﬂ ats 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm 15 mm Length (mm) 140 150 160 164 170 180 190 200 Ident. No. 208 209 210 211 212 213 214 215 52046... ● ● ● ● ● ● ● ● Width across ﬂ ats 16 mm 17 mm 18 mm 19 mm 21 mm 22 mm 24 mm Length (mm) 212 225 237 250 274 292 325 Ident. No. 216 217 218 219 221 222 224 52046... ● ● ● ● ● ● ● Prod. Gr. 530 Open-end spanners with ring ratchet - set Reversible design, angled ring side

Application: Advantage: For loosening or quickly tightening bolts and nuts . Good grip thanks to shaped design using a ratchet . Sha proﬁ le creates excellent bending rigidity Execution: . Longer service lives thanks to manganese phosphate-plated catches and pawls . 6° return angle . No edges pinched thanks to UD proﬁ le . Anti-clockwise/clockwise rotation using reversing lever . Hollow section in shank with double T shape . Ring side angled 13° with reversing lever

Composition of set Supplied lengths: 140-250 mm 8 mm | 9 mm | 10 mm | 11 mm | 12 mm | Width across fl ats 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 18 mm | 19 mm Number of pieces in assortment/set (PCS) 12 Tip profi le type UD profi le Surface Chrome-plated Material Chrome-vanadium steel Ident. No. 400 52046... ● Prod. Gr. 530 Ratchet combination spanner set OPEN-RATCH, switchable

Execution: Delivery: . Ratchet ﬁ nely toothed on ring side, 72 teeth, 5° In textile tool roll with Velcro fastener switching angle . Complete bending strength owing to proven double-T proﬁ le . Right/le switchover via lateral push button Ident. No. 510

Width across ﬂ ats Number of pieces Surface Material 52045... in assortment/set Ident. No. (PCS) 8 mm | 10 mm | Chrome-vanadium ● Ident. No. 500 13 mm | 17 mm | 5 Chrome-plated steel 500 19 mm 8 mm | 9 mm | 10 mm | 11 mm | 12 mm 13 mm 14 Chrome-vanadium | | 12 Chrome-plated 510 ● mm | 15 mm | 16 steel mm | 17 mm | 18 mm | 19 mm Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1239 Availability subject to country specific rules and regulations.

1239_EN_2018_KERN[21850729]-11.indd 1239 12/17/2018 3:35:36 PM Screwdrivers \ Open-end spanners and box wrenches

Ratchet spanner set FAST-RATCH

Execution: . Both metric and imperial nuts and bolts can be . Produced from stainless, tempered steel manipulated with one wrench . Especially suitable for union nuts

Slogging box wrench ( DIN 7444 )

Application: . Short version for use in tight installation areas For tightening or loosening heavily seized screw . Heavy-duty with large force transmission connections using a hammer. . Load distribution via UD profi le Execution: . Forged steel with excellent material strength and better resistance to cracking . Drop-forged . Short shank with reinforced block end Technical data: . Bi-hexagon geometry with UD profi le . Tip profi le type: UD profi le . Surface: Bare Advantage: . Material: Chrome-vanadium steel . Suitable for heavy-duty assembly work

Width across ﬂ ats 24 mm 27 mm 30 mm 32 mm 34 mm 36 mm 41 mm 46 mm Length (mm) 160 180 190 195 195 205 225 240 Thickness (mm) 15 15.5 16.5 16.5 16.5 19.5 20.5 22.5 Ident. No. 024 027 030 032 034 036 041 046 52047... ● ● ● ● ● ● ● ● Width across ﬂ ats 50 mm 55 mm 60 mm 65 mm 70 mm 75 mm 80 mm 85 mm Length (mm) 250 270 270 290 320 325 345 360 Thickness (mm) 23.5 25 26 29 32.5 34 35 37 Ident. No. 050 055 060 065 070 075 080 085 52047... ● ● ● ● ● ● ● ● Prod. Gr. 530

Single-ended box wrench heavy-duty design

Application: Advantage: Box wrench for maximum torques. . Drop-forged steel with excellent material strength and resistance to cracking Execution: . Transfers high torques . Drop-forged . Polished and oﬀ set ring Technical data: . Designed for use with extension bar no. 52052 . Surface: Chrome-plated . Material: Chrome-vanadium steel

Width across ﬂ ats 24 mm 27 mm 30 mm 32 mm 34 mm 36 mm 41 mm 46 mm Length (mm) 180 190 200 235 235 245 265 280 Thickness (mm) 17 17 18.4 18.4 18.4 20 22 23 Ident. No. 024 027 030 032 034 036 041 046 52052... ● ● ● ● ● ● ● ● Width across ﬂ ats 50 mm 55 mm 60 mm 65 mm 70 mm 75 mm 80 mm 85 mm Length (mm) 290 300 345 355 365 375 385 385 Thickness (mm) 25.5 28 30.5 33 30.5 38 40.5 40.5 Ident. No. 050 055 060 065 070 075 080 085 52052... ● ● ● ● ● ● ○ ● Prod. Gr. 530

Source: Hahn+Kolb Werkzeuge GmbH 1240Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1239_EN_2018_KERN[21850729]-11.indd 1240 12/17/2018 3:35:38 PM Screwdrivers \ Open-end spanners and box wrenches

Extension bar

Application: Advantage: Extension bar to extend the lever arm. . Greater torque achieved thanks to longer lever arm

Execution: Technical data: . Chrome-vanadium steel . Surface: Chrome-plated . With snap-hole Suitable for width across ﬂ ats 24-30 mm 32-41 mm 46-55 mm 60-95 mm Pipe Ø (mm) 19 22 25 30 Length (mm) 460 610 760 860 Ident. No. 005 010 020 030 52053... ● ● ● ● Prod. Gr. 530 Double ring wrench ( DIN 838 ) deep oﬀ set on both sides

Execution: . Even slightly damaged heads can still be screwed . Drop-forged on

Advantage: Technical data: . Energy profi le increases the force application areas . Tip profi le type: ENERGY profi le for optimum load distribution . Surface: Chrome-plated . Gentle on the bolt/nut and tool . Material: Chrome-vanadium steel

Width across fl ats 6 x 7 mm 8 x 9 mm 8 x 10 mm 10 x 11 mm 10 x 13 mm 12 x 13 mm 12 x 14 mm 13 x 14 mm Length (mm) 178 195 195 200 220 220 220 220 Ident. No. 500 510 520 530 540 550 560 570 52055... ● ● ● ● ● ● ● ● Width across fl ats 13 x 15 mm 13 x 17 mm 14 x 15 mm 16 x 18 mm 16 x 17 mm 14 x 17 mm 17 x 19 mm 18 x 19 mm Length (mm) 225 250 235 250 250 250 285 285 Ident. No. 580 590 600 610 620 625 630 640 52055... ● ● ● ● ● ● ● ● Width across fl ats 19 x 22 mm 19 x 24 mm 20 x 22 mm 21 x 23 mm 22 x 24 mm 24 x 26 mm 24 x 27 mm 25 x 28 mm Length (mm) 300 300 300 300 320 330 330 345 Ident. No. 650 655 660 670 680 690 700 710 52055... ● ● ● ● ● ● ● ● Width across fl ats 27 x 32 mm 30 x 32 mm 32 x 36 mm 36 x 41 mm Length (mm) 360 360 400 440 Ident. No. 720 750 760 765 52055... ● ● ● ● Prod. Gr. 5HB

Double ring wrench ( DIN 838 ) deep oﬀ set on both sides

Execution: . Deep oﬀ set makes it easier to work in hard-to- . Drop-forged reach places

Advantage: Technical data: . No pinching of edges on bolts and nuts due to . Tip profi le type: UD profi le force application on sides with optimum load . Surface: Chrome-plated distribution . Material: Chrome-vanadium steel . Sha profi le creates excellent bending rigidity Width across fl ats 6 x 7 mm 7 x 8 mm 8 x 9 mm 8 x 10 mm 9 x 11 mm 10 x 11 mm 10 x 12 mm 10 x 13 mm Length (mm) 170 180 182 182 195 195 195 212 Ident. No. 010 020 030 040 050 060 070 080 52056... ● ● ● ● ● ● ● ● Width across fl ats 11 x 13 mm 12 x 13 mm 12 x 14 mm 13 x 14 mm 13 x 15 mm 13 x 17 mm 14 x 15 mm 14 x 17 mm Length (mm) 212 212 212 225 225 225 225 245 Ident. No. 100 120 130 140 150 160 170 180 52056... ● ● ● ● ● ● ● ● Width across fl ats 16 x 17 mm 16 x 18 mm 17 x 19 mm 18 x 19 mm 18 x 21 mm 19 x 22 mm 19 x 24 mm 20 x 22 mm Length (mm) 245 265 265 265 285 285 305 287 Ident. No. 190 195 200 220 225 230 240 250 52056... ● ● ● ● ● ● ● ● Width across fl ats 21 x 23 mm 21 x 24 mm 22 x 24 mm 24 x 26 mm 24 x 27 mm 24 x 30 mm 25 x 28 mm 27 x 30 mm Length (mm) 305 307 307 325 325 345 345 345 Ident. No. 260 265 270 290 300 310 320 340 52056... ● ● ● ● ● ● ● ● Width across fl ats 27 x 32 mm 30 x 32 mm 30 x 34 mm 30 x 36 mm 32 x 36 mm 34 x 36 mm 36 x 41 mm 38 x 42 mm Length (mm) 370 370 375 400 400 420 440 440 Ident. No. 350 360 365 370 380 385 390 400 52056... ● ● ● ● ● ● ● ● Width across fl ats 41 x 46 mm 46 x 50 mm 55 x 60 mm Length (mm) 485 535 610 Ident. No. 410 420 430 52056... ● ● ● Prod. Gr. 530

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1241 Availability subject to country specific rules and regulations.

1241_EN_2018_KERN[21850733]-s.indd 1241 12/17/2018 3:35:35 PM Screwdrivers \ Open-end spanners and box wrenches

Double ring wrench ( DIN 838 ) deep oﬀ set on both sides

Execution: . Drop-forged Technical data: Advantage: . Tip profi le type: Standard profi le . Sha profi le creates excellent bending rigidity . Surface: Chrome-plated . Material: Chrome-vanadium steel . Deep off set makes it easier to work in hard-to- reach places Width across fl ats 6 x 7 mm 8 x 9 mm 10 x 11 mm 10 x 13 mm 12 x 13 mm 14 x 15 mm 16 x 17 mm 17 x 19 mm Length (mm) 178 195 200 220 220 235 250 285 Ident. No. 060 080 100 105 120 140 160 170 52059... ● ● ● ● ● ● ● ● Width across fl ats 18 x 19 mm 20 x 22 mm 24 x 27 mm 30 x 32 mm Length (mm) 285 300 330 360 Ident. No. 180 200 240 300 52059... ● ● ● ● Prod. Gr. 526

Double ring wrench ( DIN 838 ) deep oﬀ set on both sides

Execution: . Sha proﬁ le creates excellent bending rigidity . Chrome-alloy steel . Deep oﬀ set makes it easier to work in hard-to- . Drop-forged reach places

Advantage: Technical data: . High force transmission to the edges of the bolts . Tip proﬁ le type: AS drive proﬁ le and nuts for optimum load distribution . Surface: Chrome-plated . Longer bolt and nut service lives . Material: Steel, specially hardened

Width across ﬂ ats 14 x 15 mm 19 x 22 mm 20 x 22 mm 24 x 26 mm 25 x 28 mm 30 x 34 mm 36 x 41 mm 46 x 50 mm Length (mm) 245 300 300 330 350 365 440 535 Ident. No. 160 210 230 260 290 325 350 370 52064... ● ● ● ○ ● ● ● ○ Prod. Gr. 531

Double ring wrench sets ( DIN 838 ) Deep oﬀ set on both sides

Advantage: . Even slightly damaged heads can still be screwed . No. 52055: on . Energy proﬁ le increases the force application areas for optimum load distribution Technical data: . Gentle on the bolt/nut and tool . Surface: Chrome-plated . Material: Chrome-vanadium steel

No. 52055 800

Width across ﬂ ats Number of pieces in assortment/set (PCS) 52055... 52059... Ident. No. Ident. No. 6 x 7 mm 8 x 9 mm 10 x 11 mm 12 x 13 mm 14 x 15 mm | | | | 8 790 ● 790 ● | 16 x 17 mm | 18 x 19 mm | 20 x 22 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm | 14 x 15 mm | 16 x 17 mm | 18 x 19 mm | 20 x 22 mm | 24 x 27 mm | 30 10 800 ● 800 ● x 32 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 10 x 13 mm | 12 x 13 mm | 14 x 15 mm | 16 x 17 mm | 17 x 19 mm | 18 x 19 mm | 20 x 12 810 ● 810 ● 22 mm | 24 x 27 mm | 30 x 32 mm a = Prod. Gr. 5HB ORION = Prod. Gr. 526

Source: Hahn+Kolb Werkzeuge GmbH 1242Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1241_EN_2018_KERN[21850733]-s.indd 1242 12/17/2018 3:35:37 PM Screwdrivers \ Open-end spanners and box wrenches

Double ring wrench sets ( DIN 838 ) Deep oﬀ set on both sides

Advantage: Delivery: . No pinching of edges on bolts and nuts due to Packed in boxes force application on sides with optimum load distribution Technical data: . Sha profi le creates excellent bending rigidity . Tip profi le type: UD profi le Ident. No. 700 . Deep off set makes it easier to work in hard-to- . Surface: Chrome-plated reach places . Material: Chrome-vanadium steel Width across fl ats Number of pieces in assortment/set (PCS) 52056... Ident. No. 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm | 14 x 15 mm | 16 x 17 mm | 8 700 ● 18 x 19 mm | 20 x 22 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm | 14 x 15 mm 16 x 17 mm 18 x 19 mm | | | 12 710 ● 20 x 22 mm | 21 x 23 mm | 24 x 27 mm | 25 x 28 mm | 30 x 32 mm Prod. Gr. 530

Double ring wrench sets, metric and inch sizes ( DIN 838 ) Deep oﬀ set on both sides

Execution: . Deep oﬀ set makes it easier to work in hard-to- . Chrome-alloy steel reach places

Ident. No. 700 Width across ﬂ ats Number of pieces in assortment/set (PCS) 52064... Ident. No. 6 x 7 mm 8 x 9 mm 10 x 11 mm 12 x 13 mm 14 x 15 mm 16 x 17 | | | | | 8 700 ● mm | 18 x 19 mm | 20 x 22 mm 6 x 7 mm 8 x 9 mm 10 x 11 mm 12 x 13 mm 14 x 15 mm 16 x 17 | | | | | 10 715 ● mm | 18 x 19 mm | 20 x 22 mm | 24 x 27 mm | 30 x 32 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm | 14 x 15 mm | 16 x 17 mm | 18 x 19 mm | 20 x 22 mm | 21 x 23 mm | 24 x 27 mm | 25 x 28 12 720 ● mm | 30 x 32 mm 1/4 x 5/16 inch 3/8 x 7/16 inch 1/2 x 9/16 inch 5/8 x 3/4 inch | | | | 6 805 ● 11/16 x 13/16 inch | 7/8 x 15/16 inch 1/4 x 5/16 inch | 3/8 x 7/16 inch | 1/2 x 9/16 inch | 9/16 x 5/8 inch | 19/32 x 11/16 inch | 5/8 x 3/4 inch | 11/16 x 13/16 inch | 3/4 x 10 815 ● 7/8 inch | 25/32 x 13/16 inch | 7/8 x 15/16 inch Prod. Gr. 531

Double ring wrench sets ( DIN 838 ) Deep oﬀ set on both sides

Delivery: . Tip profi le type: Tractions profi le Supplied in boxes . Surface: Chrome-plated . Material: Chrome-vanadium steel Technical data: Width across fl ats Number of pieces in assortment/set (PCS) 52065... Ident. No. 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm | 14 x 15 mm | 16 x 17 mm | 18 x 8 810 ● 19 mm | 21 x 22 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm 14 x 15 mm 16 x 17 mm 18 x | | | 12 840 ● 19 mm | 20 x 22 mm | 21 x 23 mm | 24 x 26 mm | 25 x 28 mm | 27 x 32 mm Prod. Gr. 569

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1243 Availability subject to country specific rules and regulations.

1243_EN_2018_KERN[21850737]-p.indd 1243 12/17/2018 3:35:35 PM Screwdrivers \ Open-end spanners and box wrenches

Double ring wrench sets ( DIN 837 ) Straight, shape B

Execution: Technical data: . Thin-walled rings . Tip profi le type: UD profi le . Surface: Chrome-plated Advantage: . Material: Chrome-vanadium steel . Sha profi le creates excellent bending rigidity Ident. No. 700 . No pinching of edges on bolts and nuts due to force application on sides with optimum load distribution Width across fl ats Number of pieces in assortment/set (PCS) 52070... Ident. No. 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm | 14 x 15 mm | 16 x 17 mm | 18 x 8 700 ● 19 mm | 20 x 22 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm 14 x 15 mm 16 x 17 mm 18 x | | | 12 710 ● 19 mm | 20 x 22 mm | 21 x 23 mm | 24 x 26 mm | 25 x 28 mm | 27 x 32 mm Prod. Gr. 530

Double ring wrench sets ( DIN 837 ) Straight, shape B

Advantage: Technical data: . Clamp holder also suitable for wall mounting . Tip profi le type: Tractions profi le . Surface: Chrome-plated Delivery: . Material: Chrome-vanadium steel In clamp holders Width across fl ats Number of pieces in assortment/set (PCS) 52073... Ident. No. 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x Ident. No. 840 13 mm | 14 x 15 mm | 16 x 17 mm | 18 x 8 830 ● 19 mm | 21 x 22 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 13 mm 14 x 15 mm 16 x 17 mm 18 x | | | 12 840 ● 19 mm | 20 x 22 mm | 21 x 23 mm | 24 x 26 mm | 25 x 28 mm | 27 x 32 mm Prod. Gr. 569

Wrench Adjustable

Application: . Extremely large clamping range For quickly adjusting the wrench size. . With hanging eyelet . Smooth, ground jaws Execution: Ident. No. 020 . Chrome-vanadium steel Technical data: . Metric adjustment scale . Jaw position: 15 Degree . Ergonomically shaped comfort handle . Surface: Burnished

Max. width across ﬂ ats (mm) 24 29 33 Length (mm) 150 200 250 Ident. No. 015 020 025 52148... ● ● ● Prod. Gr. 5HB

Wrench Adjustable

Application: Advantage: For quickly adjusting the wrench size. . Sha proﬁ le creates excellent bending rigidity . Enables quick working with ﬂ exible wrench sizes Execution: and scale . Chrome-vanadium steel . Drop-forged Technical data: . Type B . Jaw position: 15 Degree . Polished head . Surface: Chrome-plated . Scale . With hanging eyelet

Max. width across ﬂ ats (mm) 13 19 24 29 34 Length (mm) 110 155 205 255 310 Ident. No. 010 015 020 025 030 52150... ● ● ● ● ● Prod. Gr. 5HB

Source: Hahn+Kolb Werkzeuge GmbH 1244Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1243_EN_2018_KERN[21850737]-p.indd 1244 12/17/2018 3:35:36 PM Screwdrivers \ Open-end spanners and box wrenches

Wrench Adjustable

Application: . With hanging eyelet For quickly adjusting the wrench size. Advantage: Execution: . Shank with double T-proﬁ le and excellent bending . Chrome-vanadium steel rigidity . Drop-forged . Type A Technical data: . Jaw position: 15 Degree . Polished head . Surface: Chrome-plated

Max. width across ﬂ ats (mm) 18 24 28 34 Length (mm) 155 205 255 310 Ident. No. 155 205 255 310 52150... ● ● ● ● Prod. Gr. 530 Wrench Adjustable

Application: Advantage: For quickly adjusting the wrench size. . Sha proﬁ le creates excellent bending rigidity

Execution: Technical data: . Chrome-vanadium steel . Jaw position: 22 Degree . Drop-forged . Surface: Chrome-plated . Type B . With hanging eyelet

Max. width across ﬂ ats (mm) 13 19 24 29 34 Length (mm) 110 155 205 255 310 Ident. No. 400 410 420 430 440 52150... ● ● ● ● ● Prod. Gr. 531

Wrench Adjustable

Application: Advantage: For quickly adjusting the wrench size. . Non-slip handle for secure and comfortable use . With reversible jaw, spanner is used as a pipe Execution: wrench . Reversible, movable jaw with smooth and serrated . Flexible wrench sizes with scale side . Scale Technical data: . Thermoplastic elastomer handle . Jaw position: 15 Degree . Surface: Chrome-plated Max. width across ﬂ ats (mm) 21 28 33 35 Length (mm) 158 208 257 308 Ident. No. 500 510 520 530 52150... ● ● ● ● Prod. Gr. 519

Socket wrench set 1/4” square drive 6.3, DIN 3120

Execution: . Higher torques possible . Chrome-vanadium steel inserts . Two-tone polyethylene foam inlay ensures any missing tools are instantly . Hexagon with special proﬁ le detected . Oil and chemical-resistant foam inlay Advantage: . Optimum force transmission thanks to special proﬁ le Delivery: . Bolt and nut are not damaged In powder-coated steel case with polyethylene foam inlay

Ident. No. 011 Ident. No. 021 Ident. No. 031 Ident. No. 101

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1245 Availability subject to country specific rules and regulations.

1245_EN_2018_KERN[21850740]-o.indd 1245 12/17/2018 3:35:40 PM Screwdrivers \ Socket wrenches, 1/4 inch

Drive 1/4 inch 1/4 inch 1/4 inch 1/4 inch | 1/2 inch Number of pieces in assortment/set (PCS) 18 28 42 35 4 mm | 4.5 mm | 5 mm | 4 mm | 4.5 mm | 5 mm | 4 mm | 4.5 mm | 5 mm | 5.5 mm | 7 mm | 8 mm | 10 5.5 mm | 6 mm | 7 mm | 5.5 mm | 6 mm | 7 mm | 5.5 mm | 6 mm | 7 mm | mm | 13 mm | 16 mm | 17 Sockets with hexagon-head tip provided 8 mm | 9 mm | 10 mm | 8 mm | 9 mm | 10 mm | 8 mm | 9 mm | 10 mm | mm | 18 mm | 19 mm | 22 11 mm | 12 mm | 13 mm 11 mm | 12 mm | 13 mm 11 mm | 12 mm | 13 mm mm | 24 mm | 27 mm | 30 | 14 mm | 14 mm | 14 mm mm | 32 mm Long sockets with hexagon-head tip provided - - 8 mm | 10 mm | 11 mm | - 13 mm 3 mm | 4 mm | 5 mm | 6 Sockets with socket hexagon-head tip 3 mm | 4 mm | 5 mm | 6 3 mm | 4 mm | 5 mm | 6 - mm | 8 mm | 10 mm | 12 provided mm | 8 mm mm | 8 mm mm | 14 mm | 17 mm Sockets with socket hexagon head or external - - TX10 | TX15 | TX20 | TX25 - TX tip provided | TX30 | TX40 PH1 | PH2 | PH3 | PZ1 | Sockets with cross-head tip provided - PH1 | PH2 | PZ1 | PZ2 - PZ2 | PZ3 Sockets with slotted tip provided - 4 mm | 5.5 mm | 6.5 mm 4 mm | 5.5 mm | 6.5 mm - 1/4-inch square | 150 mm | Ratchets provided 1/4-inch square | 150 mm 1/4-inch square | 150 mm 1/4-inch square | 150 mm 1/2-inch square | 255 mm 50 mm | 105 mm | 125 mm Extensions provided 50 mm | 105 mm 50 mm 50 mm | 105 mm | 250 mm Cross handles provided 115 mm 115 mm 115 mm 115 mm | 300 mm Cardan joints provided 38 mm 38 mm 38 mm 38 mm | 75 mm External dimensions of box 220 x 110 x 35 mm 220 x 110 x 35 mm 315 x 115 x 43 mm 450 x 210 x 50 mm Ident. No. 011 021 031 101 58006... ● ● ● ● Prod. Gr. 582 Socket wrench set 1/4” square drive 6.3, DIN 3120

Execution: Advantage: . Universal special nut geometry . Parts in the set are securely held in a ﬂ exible foam . suitable for hexagon, bi-hexagon, E-TX and inch inlay Delivery: In impact-resistant plastic case Drive 1/4 inch Number of pieces in assortment/set (PCS) 40 4 mm | 4.5 mm | 5 mm | 5.5 mm | 6 mm | 7 Sockets with hexagon-head tip provided mm | 8 mm | 9 mm | 10 mm | 11 mm | 12 mm | 13 mm | 14 mm Sockets with socket hexagon-head tip provided 3 mm | 4 mm | 5 mm | 6 mm | 7 mm | 8 mm TX10 | TX15 | TX20 | TX25 | TX27 | TX30 | Sockets with socket hexagon head or external TX tip provided TX40 | E5 | E6 | E7 | E8 | E10 | E11 | E12 | E14 Sockets with cross-head tip provided PH1 | PH2 | PZ1 | PZ2 Sockets with multi-tooth XZN tip M4 | M5 | M6 | M8 | M10 Ratchets provided 1/4-inch square | 120 mm Extensions provided 100 mm Drive handle provided 150 mm Cardan joints provided 35 mm Bit holder provided 1/4 inch Ident. No. 040 58006... ● Prod. Gr. 582 Socket wrench set 1/4” square drive 6.3, DIN 3120

Execution: Advantage: . Chrome-vanadium steel inserts . Two-tone polyethylene foam inlay ensures any . Matt chromium-plated missing tools are instantly detected . Ratchet with two-component handle Delivery: . Finely toothed In sheet steel case with polyethylene foam inlay . With release button

Ident. No. 050 Ident. No. 060 Drive Number of Sockets with socket Sockets with socket hexagon Ratchets Extensions provided 58006... pieces in assort- hexagon-head tip head or external TX tip provided provided Ident. No. ment/set (PCS) provided TX8 | TX9 | TX10 | TX15 | TX20 1/4 inch 18 - 1/4-inch ● | TX25 | TX27 | TX30 | TX40 | square 50 mm | 105 mm 050 E4 | E5 | E6 | E7 | E8 | E10 3 mm | 4 mm | 1/4 inch 17 TX8 | TX9 | TX10 | TX15 | TX20 1/4-inch ● 5 mm | 6 mm | square 50 mm | 105 mm 060 8 mm | TX25 | TX27 | TX30 | TX40

Prod. Gr. 582

Source: Hahn+Kolb Werkzeuge GmbH 1246Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1245_EN_2018_KERN[21850740]-o.indd 1246 12/17/2018 3:35:43 PM Screwdrivers \ Socket wrenches, 1/4 inch

Socket spanner sets With hexagon inserts, 1/4 inch square drive 6.3 DIN 3120

Execution: . Ident. No. 020: 35 socket wrench inserts, 5 operating tools . Chrome-vanadium steel . Ident. No. 030: 27 socket wrench inserts, 4 operating tools . Chrome-plated Delivery: . Ident. No. 010: 11 socket wrench inserts, 5 operating tools In painted metal case

Ident. No. 010 Ident. No. 020 Ident. No. 030

Drive 1/4 inch 1/4 inch 1/4 inch Number of pieces in assortment/set (PCS) 16 40 31 4 mm | 4.5 mm | 5 mm | 5.5 mm 4 mm | 4.5 mm | 5 mm | 5.5 mm | 4 mm | 4.5 mm | 5 mm | 5.5 mm | | 6 mm | 7 mm | 8 mm | 9 mm | Sockets with hexagon-head tip provided 6 mm | 7 mm | 8 mm | 9 mm | 10 6 mm | 7 mm | 8 mm | 9 mm | 10 10 mm | 11 mm | 12 mm | 13 mm mm | 11 mm | 13 mm mm | 11 mm | 12 mm | 13 mm | 14 mm Sockets with socket hexagon-head tip provided - 3 mm | 4 mm | 5 mm | 6 mm 4 mm | 5 mm | 6 mm Sockets with socket hexagon head or external TX tip TX8 | TX9 | TX10 | TX10 | TX15 | - TX10 | TX15 | TX20 provided TX20 | TX25 | TX27 | TX30 | TX40 Sockets with cross-head tip provided - PH1 | PH2 | PH3 | PZ1 | PZ2 | PZ3 PH1 | PH2 | PH3 | PZ1 | PZ2 | PZ3 Sockets with slotted tip provided - 3 mm | 4 mm | 6 mm 4 mm | 5 mm | 6 mm Ratchets provided 1/4-inch square 1/4-inch square 1/4-inch square Extensions provided 100 mm 50 mm 50 mm Drive handle provided 150 mm 150 mm - Cross handles provided 115 mm 115 mm 115 mm Cardan joints provided 35 mm 35 mm 35 mm External dimensions of box 195 x 105 x 33 mm 330 x 170 x 55 mm 230 x 140 x 40 mm Ident. No. 010 020 030 58010... ● ● ● Prod. Gr. 526 Socket spanner sets 1/4 inch and combination set 1/4+3/8+1/2 inch

Execution: . Reversible ratchet with two-component handle and . Chrome-vanadium steel locking button . Ident. No. 100: With ﬂ exible 145-mm extension . Individual parts are securely stored and transported using clamping function Advantage: . Any missing tools are instantly detected thanks to . High-quality insertion tools to robust, long-lasting size-related tool recesses industry-standard speciﬁ cation Delivery: In impact-resistant plastic box

Drive 1/4 inch 1/4 inch | 3/8 inch | 1/2 inch Number of pieces in assortment/ Ident. No. 500 set (PCS) 46 172 Ident. No. 100 4 mm | 4.5 mm | 5 mm | 5.5 mm | 6 4 mm | 4.5 mm | 5 mm | 5.5 mm | 7 mm | 8 mm | 9 mm | 10 mm Sockets with hexagon-head tip mm | 6 mm | 7 mm | 8 mm | | 11 mm | 12 mm | 13 mm | 14 mm provided 9 mm | 10 mm | 11 mm | 12 | 15 mm | 16 mm | 17 mm | 18 mm mm | 13 mm | 14 mm | 19 mm | 20 mm | 21 mm | 22 mm | 24 mm | 27 mm | 30 mm | 32 mm Long sockets with hexagon-head tip provided - 16 mm | 18 mm | 21 mm Sockets with socket hexagon-head 3 mm | 4 mm | 5 mm | 6 mm 3 mm | 4 mm | 5 mm | 6 mm | 7 mm | tip provided | 7 mm | 8 mm 8 mm | 10 mm | 12 mm | 14 mm TX8 | TX9 | TX10 | TX15 | TX20 | TX25 | TX27 | TX30 | TX40 | TX45 | Sockets with socket hexagon head or TX10 | TX15 | TX20 | TX25 | TX50 | TX55 | TX60 | TX70 | E4 | E5 external TX tip provided TX30 | TX40 | E6 | E7 | E8 | E10 | E11 | E12 | E14 | E16 | E18 Sockets with cross-head tip provided PH1 | PH2 | PH3 | PZ1 | PZ2 PH0 | PH1 | PH2 | PH3 | PH4 | PZ0 | | PZ3 PZ1 | PZ2 | PZ3 | PZ4 4 mm | 5 mm | 6.5 mm | 7 mm | 8 Sockets with slotted tip provided 4 mm | 5.5 mm | 7 mm mm | 10 mm | 12 mm Ratchets provided 1/4-inch square 3/8-inch square | 1/4-inch square | 1/2-inch square Extensions provided 50 mm | 100 mm | 145 mm 50 mm | 100 mm | 125 mm | 250 mm Drive handle provided 150 mm 150 mm Cross handles provided 115 mm 115 mm Cardan joints provided 35 mm 34 mm | 48 mm | 70 mm Bit holder provided 1/4 inch 1/4 inch External dimensions of box - 420 x 350 x 100 mm Ident. No. 100 500 58010... ● ● Prod. Gr. 526

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1247 Availability subject to country specific rules and regulations.

1247_EN_2018_KERN[21850743]-v.indd 1247 12/17/2018 3:35:41 PM Screwdrivers \ Socket wrenches, 1/4 inch

Adapter set ( DIN 3123 ) 6-piece

Application: Advantage: For universal use of 1/4” up to 3/4” square . Individual parts are securely stored and transported using clamping function . Any missing tools are instantly detected thanks to size-related tool recesses

Socket spanner sets With hexagon inserts, 1/4 inch square drive 6.3 DIN 3120

Execution: . Ident. No. 170: . Forged and tempered inserts . 33 inserts, 4 operating tools . Operating tools made from Gedore steel 31CrV3 . With T-handle ratchet and telescopic extension, adjustable . Ident. No. 100: 26 inserts, 6 operating tools Advantage: . Ident. No. 110: 30 inserts, 6 operating tools . So foam inlay for securely storing tools . Ident. No. 120: 11 inserts, 5 operating tools Delivery: . Ident. No. 130: 32 inserts, 5 operating tools In plastic box . Ident. No. 150: 43 inserts, 6 operating tools

Ident. No. 100 Ident. No. 110 Ident. No. 120 Ident. No. 130 Ident. No. 150 Ident. No. 170

Drive 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 4 mm | 4.5 mm | 5 4 mm | 5 mm | 6 4 mm | 5 mm | 6 4 mm | 5 mm | 6 4 mm | 5 mm | 6 4 mm | 5 mm | 6 Sockets with hexagon-head tip mm | 5.5 mm | 6 mm | 7 mm | 8 mm mm | 7 mm | 8 mm mm | 7 mm | 8 mm mm | 7 mm | 8 mm mm | 7 mm | 8 mm provided mm | 7 mm | 8 mm | 9 mm | 10 mm | | 9 mm | 10 mm | | 9 mm | 10 mm | | 9 mm | 10 mm | | 9 mm | 10 mm | | 9 mm | 10 mm | 11 mm | 12 mm | 11 mm | 12 mm | 11 mm | 13 mm | 11 mm | 12 mm | 11 mm | 12 mm | 11 mm | 13 mm 13 mm | 14 mm 13 mm 14 mm 13 mm 13 mm Sockets with socket hexagon-head 3 mm | 4 mm | 5 3 mm | 4 mm | 5 - 3 mm | 4 mm | 5 3 mm | 4 mm | 5 3 mm | 4 mm | 5 tip provided mm | 6 mm | 8 mm mm | 6 mm | 8 mm mm | 6 mm mm | 6 mm | 8 mm mm | 6 mm TX8 | TX9 | TX10 | TX8 | TX9 | TX10 TX15 | TX20 | TX25 TX10 | TX15 | TX20 TX10 | TX15 | TX20 Sockets with socket hexagon head | TX15 | TX20 | - | TX27 | TX30 | E4 - | TX25 | TX27 | | TX25 | TX27 | or external TX tip provided TX25 | TX27 | TX30 | E5 | E6 | E7 | E8 TX30 | TX40 TX30 | TX40 | TX40 | E10 Sockets with cross-head tip provided PH1 | PH2 | PH3 | - - PH1 | PH2 | PZ1 | PH1 | PH2 | PZ1 | PH1 | PH2 | PZ1 | PZ1 | PZ2 | PZ3 PZ2 | PZ3 PZ2 | PZ3 PZ2 | PZ3 4 mm | 5.5 mm | 4 mm | 5.5 mm | Sockets with slotted tip provided - - 4 mm | 6.5 mm 4 mm | 6.5 mm 6.5 mm | 8 mm 6.5 mm Ratchets provided 1/4-inch square 1/4-inch square 1/4-inch square 1/4-inch square 1/4-inch square 1/4-inch square Extensions provided 55 mm | 150 mm 55 mm | 150 mm 100 mm 97 mm 55 mm | 150 mm 186-296 mm Drive handle provided 140 mm 140 mm 140 mm 100 mm 100 mm - Cross handles provided 115 mm 115 mm 115 mm - - - Cardan joints provided 38 mm 38 mm 38 mm 38 mm 38 mm 38 mm Ident. No. 100 110 120 130 150 170 58016... ● ● ● ● ● ○ Prod. Gr. 530 Zyklop Speed socket wrench set With hexagon inserts, 1/4 inch square drive 6.3 DIN 3120

Execution: . With quick-change chuck . Zyklop Speed ratchet with 1/4” square drive and freely swivelling head with 5 speciﬁ c positions Advantage: . . Pushbutton release Ident. No. 020: . Robust metal case with so foam inlay and . Changes between anti-clockwise/clockwise non-slip rubber stoppers on the base for secure Ident. No. 015 . Finely toothed storage . Ident. No. 015: . Wobble extension enables swivelling up to 15° Ident. No. 020 . 5° return angle . Quick to change bits using the quick-action . Multi-component power grip chuck . Bits: 50 mm length Delivery: . Ident. No. 020: In fabric case with rip-tape fastening . Multi-component handle Ident. No. 015: . Extensions with quick-action rotary sleeves and Ident. No. 020: In robust metal case Flexible-Lock system

Source: Hahn+Kolb Werkzeuge GmbH 1248Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1247_EN_2018_KERN[21850743]-v.indd 1248 12/17/2018 3:35:48 PM Screwdrivers \ Socket wrenches, 1/4 inch

Drive 1/4 inch 1/4 inch Number of pieces in assortment/set (PCS) 26 42 Sockets with hexagon-head tip provided 5.5 mm | 6 mm | 7 mm | 8 mm | 10 mm | 12 mm | 13 4 mm | 4.5 mm | 5 mm | 5.5 mm | 6 mm | 7 mm | 8 mm mm | 9 mm | 10 mm | 11 mm | 13 mm | 14 mm Sockets with socket hexagon-head tip provided 3 mm | 4 mm | 5 mm | 6 mm | 8 mm 3 mm | 4 mm | 5 mm | 6 mm | 8 mm Sockets with socket hexagon head or external TX tip provided TX10 | TX15 | TX20 | TX25 | TX27 | TX30 TX8 | TX9 | TX10 | TX15 | TX20 | TX25 | TX27 | TX30 Sockets with cross-head tip provided PH1 | PH2 | PH3 | PZ1 | PZ2 | PZ3 PH1 | PH2 | PH3 | PZ1 | PZ2 | PZ3 Ratchets provided 1/4-inch square 1/4-inch square Extensions provided 75 mm | 150 mm 150 mm Cross handles provided - 115 mm Cardan joints provided - 38 mm Bit holder provided 1/4 inch 1/4 inch Ident. No. 015 020 58009... ● ● Prod. Gr. 542

Zyklop Metal socket wrench sets with hexagon inserts, 1/4 inch square drive 6.3 DIN 3120

Execution: . Ident. No. 030: Ratchet with reversing lever for . Forged all-metal ratchet with safe nut locking easy change in direction function . Ident. No. 040: Ratchet with sliding square tang . Ident. No. 030: Only 5° return angle prevents accidental switching when screwdriving . Ident. No. 040: Only 4,7° return angle Delivery: Advantage: In extremely robust yet lightweight fabric box . Extremely robust without limiting the torque Ident. No. 030 Ident. No. 040 Drive 1/4 inch Number of pieces in assortment/set (PCS) 28 Sockets with hexagon-head tip provided 5 mm | 5.5 mm | 6 mm | 7 mm | 8 mm | 10 mm | 12 mm | 13 mm Sockets with socket hexagon-head tip provided 3 mm | 4 mm | 5 mm | 6 mm Sockets with socket hexagon head or external TX tip provided TX10 | TX15 | TX20 | TX25 | TX27 | TX30 Sockets with cross-head tip provided PH1 | PH2 | PH3 | PZ1 | PZ2 Ratchets provided 1/4-inch square Extensions provided 56 mm | 150 mm Bit holder provided 1/4 inch Reversible ratchet Ident. No. 030 58009... ● Ratchet with sliding square Ident. No. 040 58009... tang ● Prod. Gr. 542

TOOL-Check socket spanner and bit set 1/4” square drive 6.3, DIN 3120

Execution: . Ident. No. 050: Bit ratchet in drop-forged, all-steel . Holding sockets, bits and adapters design . Functional fold-out holder for quick access . Ident. No. 055: . Ratchet in die-forged, all-steel design . With additional Kra form handle Drive 1/4 inch 1/4 inch Number of pieces in assortment/set (PCS) 38 38 Ident. No. 055 Ident. No. 050 5.5 mm | 6 mm | 7 mm | 8 5.5 mm | 6 mm | 7 mm | 8 Sockets with hexagon-head tip provided mm | 9 mm | 10 mm | 12 mm | 9 mm | 10 mm | 12 mm | 13 mm mm | 13 mm Sockets with socket hexagon-head tip provided 3 mm | 4 mm | 5 mm | 6 mm 3 mm | 4 mm | 5 mm | 6 mm | 8 mm | 8 mm Sockets with socket hexagon head or external TX10 | TX15 | TX20 | TX25 | TX10 | TX15 | TX20 | TX25 TX tip provided TX30 | TX40 | TX30 Sockets with cross-head tip provided PH1 | PH2 | PH3 | PZ1 | PZ2 PH1 | PH2 | PH3 | PZ1 | PZ2 | PZ3 | PZ3 Sockets with slotted tip provided 5.5 mm 5.5 mm Ratchets provided 1/4-inch square 1/4-inch square Bit holder provided 1/4 inch 1/4 inch Bit holder 1/4 inch hexagon 1/4 inch hexagon Ident. No. 050 055 58009... ● ● Prod. Gr. 542

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1249 Availability subject to country specific rules and regulations.

1247_EN_2018_KERN[21850743]-v.indd 1249 12/17/2018 3:35:57 PM Screwdrivers \ Socket wrenches, 1/4 inch

Socket spanner sets With hexagon inserts, 1/4 inch square drive 6.3 DIN 3120

Execution: . 5 E-TX socket spanner inserts . Chrome-plated . 11 screwdriver bits . Ident. No. 005: . Ident. No. 015–040: Smart-Case with safety insert system . 10 socket wrench inserts . Ident. No. 030: . 7 TX bit inserts . 12 socket wrench inserts . 6 cross-head bit inserts . 12 screwdriver bits . 3 slotted bit inserts . Ident. No. 040: . 5 hexagon socket bit inserts . HINOX stainless steel . 1 bit adapter . 18 socket wrench inserts . Ident. No. 005–030: Chrome-vanadium steel inserts Advantage: . Ident. No. 015: . 11 hexagon socket wrench inserts . Ident. No. 005: Impact-resistant “smart case” with non-slip coating for secure storage of tools

Ident. No. 005 Ident. No. 015 Ident. No. 030 Ident. No. 040

Drive 1/4 inch 1/4 inch 1/4 inch 1/4 inch Number of pieces in assortment/set (PCS) 38 33 30 24 5.5 mm | 6 mm | 7 mm | 5 mm | 5.5 mm | 6 mm | 4 mm | 5 mm | 5.5 mm | 6 4 mm | 5 mm | 5.5 mm | 6 Sockets with hexagon-head tip provided 8 mm | 9 mm | 10 mm | 7 mm | 8 mm | 9 mm | 10 mm | 7 mm | 8 mm | 9 mm mm | 7 mm | 8 mm | 9 mm 11 mm | 12 mm | 13 mm mm | 11 mm | 12 mm | 13 | 10 mm | 11 mm | 12 mm | 10 mm | 11 mm | 12 mm | 14 mm mm | 14 mm | 13 mm | 14 mm | 13 mm | 14 mm Sockets with socket hexagon-head tip 3 mm | 4 mm | 5 mm | 6 3 mm | 4 mm | 5 mm | 3 mm | 4 mm | 5 mm | 6 3 mm | 4 mm | 5 mm | 6 provided mm | 7 mm 6 mm mm | 8 mm mm | 8 mm TX10 | TX15 | TX20 | TX25 Sockets with socket hexagon head or external TX10 | TX15 | TX20 | TX25 | TX30 | E5 | E6 | E7 | E8 - - TX tip provided | TX27 | TX30 | TX40 | E10 PH1 | PH2 | PH3 | PZ1 | Sockets with cross-head tip provided PH2 PH1 | PH2 | PZ1 | PZ2 - PZ2 | PZ3 Sockets with slotted tip provided 6 mm | 10 mm | 11 mm 1 x 5.5 mm 3.5 mm | 5.5 mm | 8 mm - Ratchets provided 1/4-inch square 1/4-inch square 1/4-inch square 1/4-inch square Extensions provided 55 mm | 101 mm 55 mm | 101 mm | 147 mm 55 mm | 147 mm 55 mm | 147 mm Drive handle provided 134 mm 134 mm 134 mm 134 mm Cross handles provided - - 115 mm 115 mm Cardan joints provided 38 mm 38 mm 38 mm 38 mm Ident. No. 005 015 030 040 58020... ● ● ● ● Prod. Gr. 569

Socket wrench set 1/4 inch, 3/8 inch and 1/2 inch square drive 6.3 DIN 3120

Execution: . Smart Case with safety insert system . Chrome-vanadium steel Advantage: . Chrome-plated or steel-grey . Smart Case with safety insert system

Drive 1/4 inch | 3/8 inch | 1/2 1/4 inch | 3/8 inch | 1/2 inch inch Number of pieces in assortment/set (PCS) 29 58 TX6 | TX7 | TX8 | TX9 | TX10 TX10 | TX15 | TX20 | TX25 | TX15 | TX20 | TX25 | TX27 | TX27 | TX30 | TX40 | TX45 Ident. No. 210 Ident. No. 220 Sockets with socket hexagon head or external | TX30 | TX40 | TX45 | TX50 | TX50 | E5 | E6 | E7 | E8 TX tip provided | TX55 | TX60 | E4 | E5 | E6 | E10 | E12 | E14 | TX55 | E7 | E8 | E10 | E11 | E12 | | TX60 E14 | E16 | E18 | E20 | E24 Ratchets provided - 1/4-inch square Connection pieces provided 20 mm | 30 mm | 35 mm 20 mm | 30 mm E 6 x 8/E 10 x 12/E 14 x E 6 x 8/E 10 x 12/E 14 x Composition of set 18/E 20 x 24 18/E 20 x 24 External dimensions of box 355 x 235 x 65 mm 355 x 235 x 65 mm Ident. No. 210 220 58020... ● ● Prod. Gr. 569

Source: Hahn+Kolb Werkzeuge GmbH 1250Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1250_EN_2018_KERN[21850747]-p.indd 1250 12/17/2018 3:35:45 PM Screwdrivers \ Socket wrenches, 1/4 inch

Socket spanner sets With hexagon or bi-hexagon inserts

Execution: Advantage: . HPQ steel, die-forged . Excellent load capacity thanks to tough, hard HPQ . chrome-plated, polished steel alloy . Socket wrench inserts with AS-Drive proﬁ le . Cadmium-free, therefore also suitable for working . Ident. No. 301–311: 13 socket wrench inserts, 6 on titanium-alloy parts and titanium connecting operating tools elements . Ident. No. 311: ratchet with QuickRelease safety . High force transmission to the edges of the bolts lock and nuts for optimum load distribution Ident. No. 301–311 Ident. No. 341 . Ident. No. 341: 17 socket wrench inserts, 5 . Longer bolt and nut service lives operating tools Delivery: in robust, stackable ABS plastic storage box Drive 1/4 inch 1/4 inch 1/4 inch 3.5 mm | 4 mm | 4.5 mm | 5 mm 3.5 mm | 4 mm | 4.5 mm | 5 mm 3.5 mm | 4 mm | 4.5 mm | 5 mm Sockets with hexagon-head tip | 5.5 mm | 6 mm | 7 mm | 8 mm | | 5.5 mm | 6 mm | 7 mm | 8 mm | | 5.5 mm | 6 mm | 7 mm | 8 mm | provided 9 mm | 10 mm | 11 mm | 12 mm 9 mm | 10 mm | 11 mm | 12 mm 9 mm | 10 mm | 11 mm | 12 mm | 13 mm | 13 mm | 13 mm Sockets with socket hexagon-head tip provided - - 3 mm | 4 mm | 5 mm | 6 mm Ratchets provided 1/4-inch square 1/4-inch square 1/4-inch square Extensions provided 54 mm | 150 mm 54 mm | 150 mm 150 mm Cross handles provided 115 mm 115 mm 115 mm Cardan joints provided 38 mm 38 mm 38 mm External dimensions of box 220 x 130 x 42 mm 220 x 110 x 40 mm 220 x 130 x 42 mm Ident. No. 301 311 341 58024... ● ● ● Prod. Gr. 531

Socket spanner sets 1/4” square drive 6.3, DIN 3120

Execution: Advantage: . HPQ steel, die-forged . Excellent load capacity thanks to tough, hard HPQ steel alloy . chrome-plated, polished . Cadmium-free, therefore also suitable for working on titanium-alloy parts and . Ident. No. 321: 25 socket wrench inserts, 8 operating tools titanium connecting elements . Ident. No. 321–361: Socket wrench inserts with AS-Drive proﬁ le . High force transmission to the edges of the bolts and nuts for optimum load . Ident. No. 361: 27 socket wrench inserts, 11 operating tools distribution . Ident. No. 381: . Longer bolt and nut service lives . Bi-hexagon inserts with AS-Drive proﬁ le Delivery: . 23 socket wrench inserts, 7 operating tools in robust, stackable ABS plastic storage box

Ident. No. 321 Ident. No. 361 Ident. No. 381

Drive 1/4 inch 1/4 inch | 1/2 inch 1/4 inch 4 mm | 4.5 mm | 5 mm | 5.5 mm 3.2 mm | 3.5 mm | 4 mm | 4.5 mm | 6 mm | 7 mm | 8 mm | 9 mm | 4 mm | 4.5 mm | 5 mm | 5.5 mm | | 5 mm | 5.5 mm | 6 mm | 7 mm | 10 mm | 11 mm | 13 mm | 16 mm Sockets with hexagon-head tip provided 6 mm | 7 mm | 8 mm | 9 mm | 10 8 mm | 9 mm | 10 mm | 11 mm | | 17 mm | 18 mm | 19 mm | 21 mm | 11 mm | 12 mm | 13 mm 12 mm | 13 mm | 14 mm mm | 22 mm | 24 mm | 27 mm | 30 mm 3/16 inch | 7/32 inch | 1/4 inch | Tip size 9/32 inch | 5/16 inch | 11/32 inch - - | 3/8 inch | 7/16 inch | 1/2 inch | 9/16 inch 3 mm | 4 mm | 5 mm | 6 mm | 8 Sockets with socket hexagon-head tip provided - 3 mm | 4 mm | 5 mm | 6 mm mm | 10 mm | 12 mm | 14 mm Sockets with cross-head tip provided - - PH1 | PH2 | PH3 Sockets with slotted tip provided - - 0.6 x 3.5 mm | 0.8 x 4 mm | 1 x 5.5 mm | 1.6 x 8 mm Ratchets provided 1/4-inch square 1/4-inch square | 1/2-inch square 1/4-inch square Extensions provided 54 mm 54 mm | 130 mm | 150 mm | 255 | 150 mm mm 54 mm | 150 mm Flexible extensions provided 152 mm - - Cross handles provided 115 mm 115 mm | 300 mm 115 mm Cardan joints provided 38 mm 38 mm | 70 mm 38 mm Bit holder provided - - 1/4 inch External dimensions of box 405 x 178 x 45 mm - 315 x 134 x 46 mm Ident. No. 321 361 381 58024... ● ● ● Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1251 Availability subject to country specific rules and regulations.

1250_EN_2018_KERN[21850747]-p.indd 1251 12/17/2018 3:35:57 PM Screwdrivers \ Socket wrenches, 1/4 inch

Socket wrench set 1/4” and 3/8” square drive 6.3 DIN 3120

Execution: . Cadmium-free, therefore also suitable for working . HPQ steel, die-forged on titanium-alloy parts and titanium connecting . chrome-plated, polished elements . Hexagon and bi-hexagon inserts with AS-Drive . High force transmission to the edges of the bolts proﬁ le and nuts for optimum load distribution . 36 socket wrench inserts, 12 operating tools . Longer bolt and nut service lives Advantage: Delivery: in robust, stackable ABS plastic storage box . Excellent load capacity thanks to tough, hard HPQ steel alloy

Drive 1/4 inch | 3/8 inch 4 mm | 4.5 mm | 5 mm | 5.5 mm | 6 mm | 7 mm | 8 mm | 9 mm | 10 mm Sockets with hexagon-head tip provided | 11 mm | 12 mm | 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 18 mm | 19 mm | 21 mm | 22 mm Sockets with socket hexagon-head tip provided 3 mm | 4 mm | 5 mm | 6 mm | 8 mm Sockets with cross-head tip provided PH1 | PH2 | PH3 | PZ2 Sockets with slotted tip provided 0.5 x 3 mm | 0.6 x 3.5 mm | 0.8 x 4 mm | 1 x 5.5 mm | 1.2 x 6.5 mm | 1.6 x 8 mm Ratchets provided 1/4-inch square | 3/8-inch square Extensions provided 76 mm | 150 mm | 240 mm Cross handles provided 115 mm Cardan joints provided 38 mm | 50 mm Bit holder provided 1/4 inch | 3/8 inch External dimensions of box 405 x 178 x 45 mm Ident. No. 411 58024... ● Prod. Gr. 531

Socket wrench set 1/4” and 1/2” square drive DIN 3120

Execution: . Cadmium-free, therefore also suitable for working . HPQ steel, die-forged on titanium-alloy parts and titanium connecting . chrome-plated, polished elements . hex and TX inserts . High force transmission to the edges of the bolts and nuts for optimum load distribution . 52 socket wrench inserts, 11 operating tools . Longer bolt and nut service lives Advantage: Delivery: . Excellent load capacity thanks to tough, hard HPQ in robust, stackable ABS plastic storage box steel alloy

Drive 1/4 inch | 1/2 inch 4 mm | 4.5 mm | 5 mm | 5.5 mm | 6 mm | 7 mm | 8 mm | 9 mm | 10 mm Sockets with hexagon-head tip provided | 11 mm | 13 mm | 16 mm | 17 mm | 18 mm | 19 mm | 21 mm | 22 mm | 24 mm | 27 mm | 30 mm Sockets with socket hexagon-head tip provided 3 mm | 4 mm | 5 mm | 6 mm | 8 mm | 10 mm | 12 mm | 14 mm E4 | E5 | E6 | E7 | E8 | E10 | E11 | E12 | E14 | E16 | E18 | E20 | E22 Sockets with socket hexagon head or external TX tip provided | E24 | TX8 | TX9 | TX10 | TX15 | TX20 | TX25 | TX27 | TX30 | TX40 | TX45 | TX50 | TX55 | TX60 Ratchets provided 1/4-inch square | 1/2-inch square Extensions provided 54 mm | 130 mm | 150 mm | 255 mm Cross handles provided 115 mm | 300 mm Cardan joints provided 38 mm | 70 mm Ident. No. 421 58024... ● Prod. Gr. 531

Reversible ratchets: ﬁ ne-tooth ratchet, telescopic ratchet, Mini ratchet 1/4 inch square drive 6.3

Application: . Ident. No. 050: Ident. No. 010: Ratchet for manual socket wrench inserts and connection parts. . telescopic function: can be extended from 150 to 200 mm Ident. No. 050: ratchet for manual socket wrench bits and connectors. . ratcheting/clamping function Ident. No. 100: Ratchet for direct mounting of bits with 1/4” external hexagon. . anti-clockwise and clockwise rotation possible using reversing lever with locking button Execution: . Ident. No. 100: . Ident. No. 010: . Anti-clockwise/clockwise rotation can be switched using reversing lever . Anti-clockwise and clockwise rotation possible using reversing lever with . With thumb wheel locking button Advantage: . With hanging eyelet . Ident. No. 100: Thumb wheel for easier placement, screwing and unscrewing . Finely toothed Ident. No. 010, 100: of bolts

Ident. No. 050 Ident. No. 010 Ident. No. 100

Source: Hahn+Kolb Werkzeuge GmbH 1252Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1252_EN_2018_KERN[21850750]-k.indd 1252 12/17/2018 3:35:43 PM Screwdrivers \ Socket wrenches, 1/4 inch

Tip size 1/4 inch 1/4 inch 1/4 inch Length (mm) 150 200 100 Number of teeth (PCS) 72 72 72 Surface Chrome-plated Chrome-plated Chrome-plated Material Chrome-vanadium steel Chrome-vanadium steel Chrome-vanadium steel Material of the grip handle 2-component plastic 2-component plastic Steel Ident. No. 010 050 100 58002... ● ● ● Prod. Gr. 582 Ratchets ( DIN 3122 ) 1/4 inch square drive 6.3

Execution: . All-steel ratchet with bit direct mounting . Ident. No. 100: . Anti-clockwise/clockwise rotation can be switched using reversing lever . Freely swivellable ratchet head with 5 deﬁ ned positions at 0°,15° and 90°, le and right Advantage: . Pushbutton release . Ident. No. 100: . Anti-clockwise/clockwise rotation can be switched using knurling wheel . In the 0° position, the ratchet becomes a standard screwdriver . Multi-component power grip . Ergonomic power grip for fatigue-free work . Flywheel design and quick-action rotary sleeve for quicker screwdriving . Ident. No. 110: Forged all-metal reversible ratchet with nut locking function process . Ident. No. 120: Forged all-metal push-through ratchet with nut locking function . Ident. No. 110–120: Extremely robust without limiting the torque . Ident. No. 200:

Ident. No. 200 Ident. No. 100 Ident. No. 110 Ident. No. 120

Model Zyklop Speed Zyklop metal Zyklop metal Zyklop Mini 1 Tip size 1/4 inch 1/4 inch 1/4 inch 1/4 inch Length (mm) 152 141 141 87 Number of teeth (PCS) 72 72 38 60 Returning angle (Degree) 5 5 4.7 6 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Material Chrome-vanadium steel Chrome-vanadium steel Chrome-vanadium steel Chrome-vanadium steel Ident. No. 100 110 120 200 58009... ● ● ● ● Prod. Gr. 542

Ratchets ( DIN 3122 ) 1/4 inch square drive 6.3

Execution: . Ident. No. 040: Reversing lever and pushbutton release, extra-slim head . Ident. No. 010: Push-through square drive with ball lock Advantage: . Ident. No. 020: With metal disc reversing . Comfortable and good grip thanks to non-slip handle . Ident. No. 030: Deeper-set reversing lever with catch for central position

Ident. No. 010 Ident. No. 040 Ident. No. 020 Ident. No. 030

Tip size 1/4 inch 1/4 inch 1/4 inch 1/4 inch Length (mm) 127 127 127 127 Number of teeth (PCS) 40 72 24 72 Returning angle (Degree) 18 5 15 9 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Material Chrome-vanadium steel Chrome-vanadium steel Chrome-vanadium steel Chrome-vanadium steel Material of the grip handle 2-component plastic 2-component plastic 2-component plastic 2-component plastic Ident. No. 010 020 030 040 58260... ● ● ● ● Prod. Gr. 530

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1253 Availability subject to country specific rules and regulations.

1252_EN_2018_KERN[21850750]-k.indd 1253 12/17/2018 3:35:50 PM Screwdrivers \ Socket wrenches, 1/4 inch

Ratchets ( DIN 3122 ) 1/4 inch square drive 6.3

Execution: . forged, with lowered washer switchover . Switchable between right and le . Finely toothed, return angle 5° . Ident. No. 005: . Ident. No. 020: With ratchet head angled at 20° . Reversible ratchet in extra-short compact design . Ident. No. 040: Ratchet head, can be swivelled through 180° . For conﬁ ned installation spaces . Ident. No. 050: . Ident. No. 010: Robust design . With direct mounting of bits with 1/4” hexagon head. . Ident. No. 015: . Short and compact design

Ident. No. 010 Ident. No. 050 Ident. No. 005 Ident. No. 015 Ident. No. 020 Ident. No. 040

Tip size 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch Head design Straight Straight - Curved Rod ends Straight Length (mm) 92 115 115 115 135 95 Number of teeth (PCS) 20 20 72 20 20 20 Returning angle (Degree) - - 5 - - - Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-vanadium Chrome-vanadium Chrome-vanadium Chrome-vanadium Chrome-vanadium Chrome-vanadium Material steel steel steel steel steel steel 2-component 2-component 2-component 2-component 2-component 2-component Material of the grip handle plastic plastic plastic plastic plastic plastic Ident. No. 005 010 015 020 040 050 58264... ● ● ● ● ● ● Prod. Gr. 569

Ratchets ( DIN 3122 ) 1/4 inch square drive 6.3

Execution: . Ident. No. 040: QuickRelease safety look and reversing lever . Ident. No. 010: Reversible ratchet . Ident. No. 060: . Ident. No. 010–040: . ﬁ ne-tooth ratchet with 80 teeth for particularly low working angle of just 4.5° . Chrome-alloy steel . chrome-alloy steel . Drop-forged . drop-forged . Ident. No. 030: Bit ratchet with direct mount, reversible . QuickRelease safety lock and reversing lever

Ident. No. 030 Ident. No. 060 Ident. No. 010 Ident. No. 040

Tip size 1/4 inch 1/4 inch 1/4 inch 1/4 inch Length (mm) 117 116 117 118 Number of teeth (PCS) 22 22 22 80 Returning angle 15 10 12 4.5 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Material Steel, specially hardened Steel, specially hardened Steel, specially hardened Steel, specially hardened Material of the grip handle 2-component plastic Steel 2-component plastic 2-component plastic Ident. No. 010 030 040 060 58268... ● ○ ● ● Prod. Gr. 531

Ratchets ( DIN 3122 ) 1/4 inch square drive 6.3

Execution: . Ident. No. 020: . Ident. No. 010: . Anti-clockwise/clockwise rotation using reversing lever . 360° rotary handle for ratchet and rotary grip actuation . Dustproof ratchet head . Disc switching . Ident. No. 100: Slim reversible ratchet, with pushbutton locking . Pushbutton locking

Ident. No. 020 Ident. No. 100 Ident. No. 010

Tip size 1/4 inch 1/4 inch 1/4 inch Length (mm) 120 121 120 Number of teeth (PCS) 60 72 72 Returning angle (Degree) 6 5 5 Surface Chrome-plated Chrome-plated Chrome-plated Material Chrome-vanadium steel Chrome-vanadium steel Chrome-vanadium steel Ident. No. 010 020 58273... ● ● - Ident. No. - - 100 58273... ● FACOM = Prod. Gr. 5JD BAHCO = Prod. Gr. 519

Source: Hahn+Kolb Werkzeuge GmbH 1254Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1254_EN_2018_KERN[21850754]-r.indd 1254 12/17/2018 3:35:58 PM Screwdrivers \ Socket wrenches, 1/4 inch

Ratchet ( DIN 3122 ) 1/4” square drive 6.3, DIN 3120

Execution: . Anti-clockwise and clockwise rotation possible using reversing lever with locking button Tip size 1/4 inch Length (mm) 150 Number of teeth (PCS) 72 Surface Chrome-plated Material Chrome-vanadium steel Ident. No. 500 58274... ● Prod. Gr. 526 Operating tools ( DIN 3120 ) 1/4 inch square drive 6.3

Application: Execution: No. 58003: Drive handle for manual socket wrench . No. 58003: Screwdriver handle with 1/4” internal inserts and connection parts and external square No. 58003 No. 58006 No. 58006: drive handle for manual socket wrench . No. 58006: 2-component screwdriver handle with inserts and connection parts 1/4-inch square drive Tip size 1/4 inch Surface Chrome-plated Material Chrome-vanadium steel Length (mm) 150 Ident. No. 080 58003... ● 205 Ident. No. 085 58006... ● Prod. Gr. 582 Operating tools ( DIN 3120 ) 1/4 inch square drive 6.3

Application: Execution: T-handle for manual socket wrench inserts and . Movable sliding head connection parts Tip size 1/4 inch Surface Chrome-plated Material Chrome-vanadium steel Length (mm) 115 Ident. No. 010 58185... ● Prod. Gr. 582 Socket wrench insert, short and long ( DIN 3124 ) Hexagon, 1/4 inch square drive 6.3 DIN 3120

Advantage: Technical data: . Optimum force transmission thanks to special . Drive: 1/4 inch profi le . Tip profi le type: Special profi le . Bolt and nut are not damaged . Surface: Chrome-plated . Material: Chrome-vanadium steel . Higher torques possible

No. 58030

Width across fl ats 4 mm 4.5 mm 5 mm 5.5 mm 6 mm 7 mm Outer Ø (mm) 11 11 11 11 11 11 Length (mm) Standard 25 Ident. No. 040 045 050 055 060 070 58030... version ● ● ● ● ● ● Long version 50 Ident. No. 040 045 050 055 060 070 58042... ● ● ● ● ● ● Width across fl ats 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm Outer Ø (mm) 12 13 14 16 17 18 Length (mm) Standard 25 Ident. No. 080 090 100 110 120 130 58030... version ● ● ● ● ● ● Long version 50 Ident. No. 080 090 100 110 120 130 58042... ● ● ● ● ● ● Width across fl ats 14 mm Outer Ø (mm) 20 Length (mm) Standard 25 Ident. No. 140 58030... version ● Width across fl ats 14 mm Outer Ø (mm) 20 Length (mm) Long version 50 Ident. No. 140 58042... ● Prod. Gr. 582 Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1255 Availability subject to country specific rules and regulations.

1254_EN_2018_KERN[21850754]-r.indd 1255 12/17/2018 3:35:59 PM Screwdrivers \ Socket wrenches, 1/4 inch

Socket spanner inserts ( DIN 3120 ) For external TORX screws, 1/4 inch square drive 6.3 DIN 3120

Execution: . Polished . Technical data: Knurled . Drive: 1/4 inch Advantage: . Surface: Chrome-plated . Material: Chrome-vanadium steel . Secure handling thanks to non-slip knurling

Tip size E4 E5 E6 E7 E8 E10 Ident. No. 040 050 060 070 080 100 58057... ● ● ● ● ● ● Prod. Gr. 582

Screwdriver bit ( DIN 3120 ) For slotted screws, 1/4” square drive, 6.3, DIN 3120

Execution: Technical data: . Burnished tips . Drive: 1/4 inch . Surface: Chrome-plated Advantage: . Material: Chrome-vanadium steel . Improved resistance to corrosion thanks to burnishing process

Width of cutting edge (mm) 4.0 5.5 6.5 Thickness of cutting edge (mm) 0.8 1.0 1.2 Ident. No. 060 070 080 58073... ● ● ● Prod. Gr. 582

Screwdriver bit ( DIN 3120 ) For slotted screws, 1/4” square drive, 6.3, DIN 3120

Width of cutting edge (mm) 5.5 8.0 10.0 Thickness of cutting edge (mm) 1.0 1.2 1.6 Ident. No. 070 100 140 58074... ● ● ● Prod. Gr. 569

Screwdriver bits ( DIN 3120 ) For Phillips screws

Advantage: . CVD-TiN coating enables longer service lives, facilitates greater torque application and ensures Technical data: resistance to corrosion . Drive: 1/4 inch . Surface: TiN . Better grip in the bolt with Cam-Out eﬀ ect kept to . Material: Chrome-vanadium steel a minimum No. 58090 Tip size PH1 PH2 PH3 PH4 PZ1 PZ2 PZ3 Ident. No. 010 020 030 040 58090... ● ● ● ● - - - Ident. No. - - - - 010 020 030 58106... ● ● ● Prod. Gr. 569

Source: Hahn+Kolb Werkzeuge GmbH 1256Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1254_EN_2018_KERN[21850754]-r.indd 1256 12/17/2018 3:36:00 PM Screwdrivers \ Socket wrenches, 1/4 inch

Screwdriver bits ( DIN 3120 ) For Phillips screws

Execution: Technical data: . Burnished tips . Drive: 1/4 inch . Surface: Chrome-plated Advantage: . Material: Chrome-vanadium steel . Improved resistance to corrosion thanks to burnishing process

Tip size PH1 PH2 PH3 PZ1 PZ2 PZ3 Ident. No. 010 020 030 58091... ● ● ● - - - Ident. No. - - - 010 020 030 58092... ● ● ● Prod. Gr. 582

Screwdriver bits ( DIN 3120 ) For hexagon socket screws, 1/4 inch square drive 6.3 DIN 3120

Execution: Advantage: . No. 58120 030–58120 080, 58126 030–58126 060: Burnished tips . No. 58120 030–58120 080, 58126 030–58126 060: Improved resistance to . No. 58126: long version total length 55 mm, blade length 30 mm corrosion thanks to burnishing process . No. 58122: CVD-TiN coating enables longer service lives, facilitates greater torque application and ensures resistance to corrosion

No. 58120 No. 58122 No. 58126

Drive 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch Width across ﬂ ats 3 mm 4 mm 5 mm 6 mm 8 mm Tip type Hexagon Hexagon Hexagon Hexagon Hexagon Surface Material Chrome-plated Chrome-vana- Ident. No. 030 040 050 060 080 58120... dium steel ● ● ● ● ● Chrome-vana- 030 040 050 060 080 58122... TiN dium steel Ident. No. ● ● ● ● ● Chrome-plated Chrome-vana- Ident. No. 030 040 050 060 58126... dium steel ● ● ● ● - STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569 a = Prod. Gr. 582

Screwdriver bits ( DIN 3120 ) For internal TORX screws, 1/4 inch square drive 6.3 DIN 3120

Execution: . No. 58138: CVD-TiN coating enables longer . No. 58137: Burnished tips service lives, facilitates greater torque application and ensures resistance to corrosion Advantage: . No. 58137: Improved resistance to corrosion Technical data: thanks to burnishing process . Drive: 1/4 inch . Material: Chrome-vanadium steel No. 58137

No. 58138

Tip size TX8 TX9 TX10 TX15 TX20 TX25 TX27 TX30 TX40 Surface Chrome- 008 009 010 015 020 025 027 030 040 58137... plated Ident. No. ● ● ● ● ● ● ● ● ● TiN Ident. No. 008 009 010 015 020 025 027 030 040 58138... ● ● ● ● ● ● ● ● ● HAZET = Prod. Gr. 569 a = Prod. Gr. 582 Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1257 Availability subject to country specific rules and regulations.

1257_EN_2018_KERN[21850758]-l.indd 1257 12/17/2018 3:35:54 PM Screwdrivers \ Socket wrenches, 1/4 inch

Adapters with ball detent ( DIN 3123 ) 1/4” square drive 6.3, DIN 3120

Application: Advantage: For adapting a 1/4” internal square drive to a 3/8” . No. 58158: external square drive. . Excellent load capacity thanks to tough, hard HPQ steel alloy Execution: . Cadmium-free, therefore also suitable for . Ball lock working on titanium-alloy parts and titanium No. 58149 connecting elements Drive 1/4 inch Tip size 3/8 inch Surface Chrome-plated Material Chrome-vanadium steel Ident. No. 010 58149... ● 010 58150... Chrome-vanadium steel Ident. No. ● Chrome-vanadium steel Ident. No. 010 58154... ● Steel, specially hardened Ident. No. 010 58158... ● GEDORE = Prod. Gr. 530 STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569 a = Prod. Gr. 582

Adapter with ball detent ( DIN 3123 ) 1/4” square drive 6.3, DIN 3120

Application: Execution: For connecting two 1/4” internal squares. . Ground . Ball lock Tip size 1/4 inch Surface Chrome-plated Material Chrome-vanadium steel Ident. No. 005 58150... ● Prod. Gr. 530

Adapter with ball detent ( DIN 3123 ) 1/4” square drive 6.3, DIN 3120

Application: Advantage: For adapting a 1/4” internal square drive to a 1/2” . Excellent load capacity thanks to tough, hard HPQ external square drive. steel alloy . Cadmium-free, therefore also suitable for working Execution: on titanium-alloy parts and titanium connecting . Polished elements . Ball lock Drive 1/4 inch Tip size 1/2 inch Surface Chrome-plated Material Steel, specially hardened Ident. No. 020 58158... ● Prod. Gr. 531

Bit adapter ( DIN 3120 ) 1/4” square drive 6.3, DIN 3120

Application: 1/4” external square drive Screwdriver adaptation from 1/4” square drive to a Drive 1/4 inch Tip size 1/4 inch Surface Bare Material Chrome-vanadium steel Ident. No. 090 58003... ● Prod. Gr. 582

Source: Hahn+Kolb Werkzeuge GmbH 1258Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1257_EN_2018_KERN[21850758]-l.indd 1258 12/17/2018 3:35:56 PM Screwdrivers \ Socket wrenches, 1/4 inch

Bit holder 1/4” square drive 6.3, DIN 3120

Application: . Hexagon socket with annular pressure spring Holder for 1/4” hexagonal bits with 1/4” square drive Advantage: . Also suitable for hexagons as per DIN 3126-E 6.3 Execution: (ISO 1173) with wide groove . Polished Drive 1/4 inch Bit holder 1/4 inch hexagon Surface Chrome-plated Material Steel, specially hardened Ident. No. 010 58174... ● Prod. Gr. 531 Extensions ( DIN 3123 ) 1/4 inch square drive 6.3 DIN 3120

Application: Execution: Extension for hand-operated socket wrench inserts . Polished with 1/4” square drive Drive 1/4 inch 1/4 inch 1/4 inch Tip size 1/4 inch 1/4 inch 1/4 inch Length (mm) 50 105 150 Outer Ø (mm) 11 11 11 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-vanadium Chrome-vanadium Chrome-vanadium Material steel steel steel Ident. No. 010 020 030 58227... ● ● ● Prod. Gr. 582 Cardan joints ( DIN 3123 ) With internal detent 1/4 inch square drive 6.3 DIN 3120

Application: . With inner lock Cardan joint for screw connections with projecting edges and conﬁ ned installation areas Advantage: . Flexible bending angle for diﬃ cult-to-reach instal- Execution: lation areas No. 58247 . Polished

No. 58248 Drive Tip size Surface Material 58247... 58248... Ident. No. Ident. No. 1/4 inch 1/4 inch Chrome-plated Chrome-vanadium steel 010 ● 010 ● HAZET = Prod. Gr. 569 a = Prod. Gr. 582

Socket wrench set 3/8” square drive 10, DIN 3120

Execution: . Bolt and nut are not damaged . Chrome-vanadium steel . Higher torques possible . 17 inserts, 6 operating tools . Two-tone foam inlay ensures any missing tools are . Hexagons with special proﬁ le instantly detected Advantage: Delivery: . Optimum force transmission thanks to special In sheet steel box, powder-coated, with two-tone proﬁ le foam inlay and removable recesses Drive 3/8 inch Number of pieces in assortment/set (PCS) 23 6 mm | 7 mm | 8 mm | 9 mm | 10 mm | 11 Sockets with hexagon-head tip provided mm | 12 mm | 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 18 mm | 19 mm | 20 mm | 21 mm | 22 mm Ratchets provided 3/8-inch square Extensions provided 50 mm | 75 mm | 150 mm Cardan joints provided 55 mm External dimensions of box 315 x 115 x 43 mm Ident. No. 011 58278... ● Prod. Gr. 582

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1259 Availability subject to country specific rules and regulations.

1259_EN_2018_KERN[21850761]-j.indd 1259 12/17/2018 3:35:55 PM Screwdrivers \ Socket wrench 3/8 inch

Socket wrench set With hexagon inserts, 3/8 inch square drive 10 DIN 3120

Execution: Advantage: . Chrome-vanadium steel . Ident. No. 100: . Ident. No. 010: . High-quality insertion tools to robust, long- . Matt chromium-plated lasting industry-standard speciﬁ cation . 17 inserts, 6 operating tools . Reversible ratchet with two-component handle and locking button . Individual parts are securely stored and transported using clamping function Drive 3/8 inch 3/8 inch Number of pieces in assortment/set (PCS) 23 61 Ident. No. 010 6 mm | 7 mm | 8 mm | 9 mm 6 mm | 7 mm | 8 mm | 9 mm | 10 mm | 11 mm | 12 mm | 10 mm | 11 mm | 12 mm Ident. No. 100 Sockets with hexagon-head tip provided | 13 mm | 14 mm | 15 mm | 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 18 mm | 16 mm | 17 mm | 18 mm | 19 mm | 20 mm | 21 mm | 19 mm | 20 mm | 21 mm | | 22 mm 22 mm | 24 mm 8 mm | 9 mm | 10 mm | Long sockets with hexagon-head tip provided - 11 mm | 12 mm | 13 mm | 14 mm | 15 mm | 17 mm | 19 mm Sockets with socket hexagon-head tip provided - 3 mm | 4 mm | 5 mm | 6 mm | 7 mm | 8 mm | 10 mm Sockets with socket hexagon head or external TX15 | TX20 | TX25 | TX27 TX tip provided - | TX30 | TX40 | TX45 | TX50 | TX55 Sockets with cross-head tip provided - PH1 | PH2 | PH3 | PZ1 | PZ2 | PZ3 Sockets with slotted tip provided - 5.5 mm | 7 mm | 8 mm Ratchets provided 3/8-inch square 3/8-inch square Extensions provided 125 mm | 250 mm 75 mm | 250 mm Cross handles provided 170 mm 170 mm Cardan joints provided 46 mm - External dimensions of box 270 x 105 x 90 mm - Ident. No. 010 100 58279... ● ● Prod. Gr. 526 Socket spanner sets With hexagon or bi-hexagon inserts, 3/8 inch square drive 10 DIN 3120

Execution: . Ident. No. 020: 16 hexagon inserts, 10 screwdriver . Chrome-vanadium steel bits, 6 operating tools . Ident. No. 010: Delivery: . Chrome-plated Smart Case with safety insert system . 11 inserts, 5 operating tools Drive 3/8 inch 3/8 inch Number of pieces in assortment/set (PCS) 16 32 6 mm | 7 mm | 8 mm | 9 mm 8 mm | 10 mm | 11 mm | 12 | 10 mm | 11 mm | 12 mm Ident. No. 010 Ident. No. 020 mm | 13 mm | 14 mm | 15 Sockets with hexagon-head tip provided | 13 mm | 14 mm | 15 mm mm | 17 mm | 19 mm | 21 | 16 mm | 17 mm | 18 mm | mm | 22 mm 19 mm | 21 mm | 22 mm Sockets with socket hexagon-head tip provided - 4 mm | 5 mm | 6 mm | 8 mm Sockets with cross-head tip provided - PH1 | PH2 | PH3 Sockets with slotted tip provided - 1 x 5.5 mm | 1.2 x 8 mm | 1.6 x 10 mm Ratchets provided 3/8-inch square 3/8-inch square Extensions provided 126 mm | 254 mm 75 mm | 126 mm | 254 mm Cross handles provided 198 mm 198 mm Cardan joints provided 46 mm 46 mm External dimensions of box 355 x 235 x 65 mm 355 x 235 x 65 mm Ident. No. 010 020 58280... ● ● Prod. Gr. 569

Source: Hahn+Kolb Werkzeuge GmbH 1260Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1259_EN_2018_KERN[21850761]-j.indd 1260 12/17/2018 3:35:57 PM Screwdrivers \ Socket wrench 3/8 inch

Socket spanner sets With hexagon or bi-hexagon inserts, 3/8 inch square drive 10 DIN 3120

Execution: . No. 58284: 12 inserts, 5 operating tools . Chrome-vanadium steel 31CrV3 Delivery: . No. 58280: 14 inserts, 2 operating tools In powder-coated metal case Drive 3/8 inch 3/8 inch Number of pieces in assortment/set (PCS) 14 17 6 mm | 7 mm | 8 mm | 9 mm No. 58280 Sockets with double hexagon-head tip provided | 10 mm | 11 mm | 13 mm - | 14 mm | 15 mm | 16 mm | 17 mm | 19 mm No. 58284 6 mm | 7 mm | 8 mm | 9 mm Sockets with hexagon-head tip provided - | 10 mm | 11 mm | 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 19 mm Ratchets provided 3/8-inch square 3/8-inch square Extensions provided 125 mm 125 mm | 250 mm Cross handles provided - 163 mm Cardan joints provided - 46 mm External dimensions of box 206 x 62 x 40 mm 318 x 118 x 37 mm Ident. No. 045 58280... ● - Ident. No. - 060 58284... ● Prod. Gr. 530 Socket spanner sets With hexagon or bi-hexagon inserts, 3/8 inch square drive 10 DIN 3120

Execution: . Ident. No. 111: 19 inserts, 5 operating tools . Chrome-alloy steel . Ident. No. 121: 28 inserts, 5 operating tools . Ident. No. 081: . 14 inserts, 5 operating tools Delivery: in robust, stackable ABS plastic storage box . Operating tools with QuickRelease safety lock

Ident. No. 081 Ident. No. 111 Ident. No. 121

Drive 3/8 inch 3/8 inch 3/8 inch Number of pieces in assortment/set (PCS) 19 24 33 7 mm | 8 mm | 9 mm | 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 18 8 mm | 9 mm | 10 mm | 11 mm | 8 mm | 10 mm | 11 mm | 12 mm | mm | 19 mm | 20 mm | 21 mm | 12 mm | 13 mm | 14 mm | 15 mm Sockets with double hexagon-head tip provided 13 mm | 14 mm | 15 mm | 16 mm 22 mm | 1/4 inch | 5/16 inch | | 16 mm | 17 mm | 18 mm | 19 | 17 mm | 18 mm | 19 mm 11/32 inch | 3/8 inch | 7/16 inch mm | 21 mm | 22 mm | 1/2 inch | 9/16 inch | 5/8 inch | 11/16 inch | 3/4 inch | 13/16 inch | 7/8 inch Sockets with socket hexagon-head tip provided - 3 mm | 4 mm | 5 mm | 6 mm | 7 - mm | 8 mm | 10 mm Ratchets provided 3/8-inch square 3/8-inch square 3/8-inch square Extensions provided 76 mm | 240 mm 76 mm | 240 mm 76 mm | 240 mm Cross handles provided 165 mm 165 mm 165 mm Cardan joints provided 46 mm 46 mm 46 mm External dimensions of box 315 x 115 x 45 mm 405 x 178 x 45 mm 405 x 178 x 45 mm Ident. No. 081 111 121 58288... ● ● ○ Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1261 Availability subject to country specific rules and regulations.

1261_EN_2018_KERN[21850764]-n.indd 1261 12/17/2018 3:35:55 PM Screwdrivers \ Socket wrench 3/8 inch

Socket wrench set 3/8” square drive 10, DIN 3120

Execution: Delivery: . HPQ heavy-duty steel in robust, stackable ABS plastic storage box . 32 inserts, 5 operating tools Drive 3/8 inch Number of pieces in assortment/set (PCS) 37 8 mm | 10 mm | 11 mm | 12 mm | 13 mm | Sockets with double hexagon-head tip provided 14 mm | 15 mm | 16 mm | 17 mm | 18 mm | 19 mm Sockets with socket hexagon-head tip provided 4 mm | 5 mm | 6 mm | 7 mm | 8 mm | 10 mm TX9 | TX10 | TX15 | TX20 | TX25 | TX27 | Sockets with socket hexagon head or external TX tip provided TX30 | TX40 | E5 | E6 | E7 | E8 | E10 | E12 | E14 Ratchets provided 3/8-inch square Extensions provided 76 mm | 240 mm Cross handles provided 165 mm Cardan joints provided 46 mm Ident. No. 131 58288... ● Prod. Gr. 531 Zyklop Speed socket wrench set 3/8” square drive 10, DIN 3120

Execution: . With quick-change chuck . Zyklop Speed ratchet with 3/8” square drive and freely swivelling head with 5 speciﬁ c positions Advantage: . Wobble extension enables swivelling up to 15° . Pushbutton release . Quick to change bits using the quick-action chuck . Changes between anti-clockwise/clockwise . Finely toothed Delivery: . Multi-component handle Robust metal case with so foam inlay and non-slip . Extensions with quick-action rotary sleeves and rubber stoppers Flexible-Lock system Drive 3/8 inch Number of pieces in assortment/set (PCS) 43 6 mm | 7 mm | 8 mm | 9 mm | 10 mm | 11 Sockets with hexagon-head tip provided mm | 12 mm | 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 19 mm | 22 mm | 24 mm Sockets with socket hexagon-head tip provided 3 mm | 4 mm | 5 mm | 6 mm | 8 mm | 10 mm Sockets with socket hexagon head or external TX tip provided TX10 | TX15 | TX20 | TX25 | TX27 | TX30 | TX40 Sockets with cross-head tip provided PH2 | PH3 | PZ2 | PZ3 Sockets with slotted tip provided 5.5 mm Ratchets provided 3/8-inch square Extensions provided 125 mm | 200 mm Cross handles provided 165 mm Cardan joints provided 50 mm Bit holder provided 1/4 inch Ident. No. 020 58276... ● Prod. Gr. 542 Zyklop Speed socket wrench set 3/8” square drive 10, DIN 3120

Execution: . Zyklop Speed ratchet with 3/8” square drive and freely swivelling head with 5 speciﬁ c positions Technical data: . Drive: 3/8 inch . pushbutton release . Number of pieces in assortment/set: 29 PCS . changes between anti-clockwise/clockwise . Sockets with hexagon-head tip provided: 8 mm | . ﬁ nely toothed 10 mm | 12 mm | 13 mm | 15 mm | 16 mm | 17 . multi-component handle mm | 18 mm | 19 mm . extensions with quick-action rotary sleeves and . Sockets with socket hexagon-head tip provided: 4 Flexible-Lock system mm | 5 mm | 6 mm | 8 mm . Sockets with socket hexagon head or external TX . all bits 50 mm in length tip provided: TX20 | TX25 | TX27 | TX30 | TX40 . with quick-change chuck . Sockets with cross-head tip provided: PH1 | PH2 | PH3 PZ1 PZ2 PZ3 Advantage: | | | . Sockets with slotted tip provided: 5.5 mm . wobble extension enables swivelling up to 15° . Ratchets provided: 3/8-inch square . quick change of bits using the quick-change chuck . Extensions provided: 76 mm | 200 mm . Bit holder provided: 1/4 inch Delivery: in fabric case with Velcro closure

Ident. No. 025 58276... ● Prod. Gr. 542

Source: Hahn+Kolb Werkzeuge GmbH 1262Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1261_EN_2018_KERN[21850764]-n.indd 1262 12/17/2018 3:35:59 PM Screwdrivers \ Socket wrench 3/8 inch

Zyklop Metal socket wrench sets 3/8” square drive 10, DIN 3120

Execution: . Ident. No. 030: Ratchet with reversing lever for . Forged all-metal ratchet with safe nut locking easy change in direction function . Ident. No. 040: Ratchet with sliding square tang . Ident. No. 030: Only 5° return angle prevents accidental switching when screwdriving . Ident. No. 040: Only 4,7° return angle Delivery: Advantage: In extremely robust yet lightweight fabric box . Extremely robust without limiting the torque Ident. No. 030 Ident. No. 040 Drive 3/8 inch Number of pieces in assortment/set (PCS) 29 8 mm | 10 mm | 12 mm | 13 Sockets with hexagon-head tip provided mm | 15 mm | 16 mm | 17 mm | 18 mm | 19 mm Sockets with socket hexagon-head tip provided 3 mm | 4 mm | 5 mm | 6 mm | 8 mm Sockets with socket hexagon head or external TX tip provided TX15 | TX20 | TX25 | TX27 | TX30 | TX40 Sockets with cross-head tip provided PH1 | PH2 | PH3 | PZ1 | PZ2 Ratchets provided 3/8-inch square Extensions provided 76 mm | 200 mm Bit holder provided 1/4 inch Reversible ratchet Ident. No. 030 58276... ● Push-through ratchet Ident. No. 040 58276... ● Prod. Gr. 542 Ratchet 3/8” square drive 10, DIN 3120

Application: Execution: Ratchet for manual socket wrench inserts and . Anti-clockwise and clockwise rotation possible connection parts using reversing lever with locking button . Finely serrated . With hanging eyelet Tip size 3/8 inch Length (mm) 190 Number of teeth (PCS) 72 Surface Chrome-plated Material Chrome-vanadium steel Material of the grip handle 2-component plastic Ident. No. 010 58275... ● Prod. Gr. 582 Zyklop Speed ratchet 3/8” square drive 10, DIN 3120

Execution: . Pushbutton release . Freely swivellable ratchet head with 5 deﬁ ned . Anti-clockwise/clockwise rotation can be switched positions at 0°,15° and 90°, le and right using knurling wheel . Flywheel design with quick-action rotary sleeve . Multi-component power grip

Tip size 3/8 inch Length (mm) 199 Number of teeth (PCS) 72 Returning angle (Degree) 5 Surface Chrome-plated Material Chrome-vanadium steel Ident. No. 100 58276... ● Prod. Gr. 542 Zyklop Metal ratchets 3/8 inch square drive 10 DIN 3120

Execution: . Ident. No. 110: Ratchet with reversing lever for . Forged all-metal ratchet with safe nut locking easy change in direction function . Ident. No. 120: Ratchet with sliding square tang prevents accidental switching when screwdriving Advantage: . Extremely robust without limiting the torque

Tip size 3/8 inch 3/8 inch Ident. No. 110 Ident. No. 120 Length (mm) 222 222 Number of teeth 72 76 Returning angle (Degree) 5 4.7 Surface Chrome-plated Chrome-plated Material Chrome-vanadium steel Chrome-vanadium steel Ident. No. 110 120 58276... ● ● Prod. Gr. 542

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1263 Availability subject to country specific rules and regulations.

1263_EN_2018_KERN[21850767]-n.indd 1263 12/17/2018 3:35:58 PM Screwdrivers \ Socket wrench 3/8 inch

Ratchets 3/8” square drive 10, DIN 3120

Execution: . Ident. No. 030: Deeper-set reversing lever with Advantage: . Ident. No. 020: With metal disc reversing catch for central position . Comfortable and good grip thanks to non-slip . Ident. No. 040: Reversing lever and pushbutton handle release, extra-slim head

Ident. No. 040 Ident. No. 020 Ident. No. 030 Tip size 3/8 inch 3/8 inch 3/8 inch Length (mm) 200 200 200 Number of teeth (PCS) 72 32 60 Returning angle (Degree) 5 11.25 6 Surface Chrome-plated Chrome-plated Chrome-plated Material Chrome-vanadium steel Chrome-vanadium steel Chrome-vanadium steel Material of the grip handle 2-component plastic 2-component plastic 2-component plastic Ident. No. 020 030 040 58560... ● ● ● Prod. Gr. 530 Ratchet 3/8” square drive 10, DIN 3120

Execution: Advantage: . Type C . Comfortable and good grip thanks to non-slip . Anti-clockwise/clockwise rotation using reversing handle lever Tip size 3/8 inch Length (mm) 199 Number of teeth (PCS) 30 Surface Chrome-plated Material Chrome-vanadium steel Material of the grip handle 2-component plastic Ident. No. 020 58564... ● Prod. Gr. 569 Ratchets 3/8” square drive 10, DIN 3120

Execution: . Ident. No. 020–025: Anti-clockwise/clockwise . ﬁ ne-tooth ratchet with 80 teeth for particularly . Ident. No. 010: Anti-clockwise/clockwise rotation rotation using reversing lever low working angle of just 4.5° using reversing disc . Ident. No. 025–040: QuickRelease safety lock . chrome-alloy steel . Ident. No. 010–025: Chrome-alloy steel . Ident. No. 040: Advantage: . Ident. No. 010–025: Non-slip, ergonomic handle

Ident. No. 025 Ident. No. 040 Ident. No. 010 Ident. No. 020

Tip size 3/8 inch 3/8 inch 3/8 inch 3/8 inch Length (mm) 194 193 195 192 Number of teeth (PCS) 60 30 30 80 Returning angle (Degree) 6 - - 4.5 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Material Steel, specially hardened Steel, specially hardened Steel, specially hardened Steel, specially hardened Material of the grip handle 2-component plastic 2-component plastic 2-component plastic - Ident. No. 010 020 025 040 58568... ● ● ● ● Prod. Gr. 531 VDE ratchet 3/8” square drive

Execution: . QuickRelease technology prevents uncontrolled . ﬁ ne-tooth ratchet with 80 teeth for particularly low release of tools working angle of just 4.5° . individually tested DIN EN 60900 . socket sits precisely with minimum play on the square Tip size 3/8 inch Length (mm) 205 Number of teeth 80 Returning angle 4.5 Material of the grip handle 2-component plastic VDE certiﬁ ed Yes Ident. No. 150 58568... ● Prod. Gr. 531 Source: Hahn+Kolb Werkzeuge GmbH 1264Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1263_EN_2018_KERN[21850767]-n.indd 1264 12/17/2018 3:35:59 PM Screwdrivers \ Socket wrench 3/8 inch

Actuating tool ( DIN 3122 ) 3/8” square drive 10, DIN 3120

Application: Technical data: T-handle for hand-operated socket wrench inserts . Tip size: 3/8 inch and connection parts with 3/8” square drive. . Surface: Chrome-plated No. 58479 010, 58488 No. 58484 Execution: 010 . Polished . Movable sliding head

Length (mm) Material Chrome-vanadium 010 58479... 163 steel Ident. No. ● Chrome-vanadium 010 58480... 163 steel Ident. No. ● Chrome-vanadium 010 58484... 198 steel Ident. No. ● Steel, specially 010 58488... 165 hardened Ident. No. ● GEDORE = Prod. Gr. 530 STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569 a = Prod. Gr. 582

GRIPPER universal screwdriver ( DIN 3120 ) 3/8” square drive 10, DIN 3120

Application: . Head height up to 8 mm Universal tool for nuts and bolts with external proﬁ le. Advantage: Execution: . Replaces nuts in the region of 7 to 19 mm . Alloyed steel housing . Independent of imperial or metric sizes . 54 hardened steel pins . All geometries such as triangular, square, hexag- . Pins with spring and solid stop onal or octagonal, slightly damaged screws, and . Torque transfer of up to 80 Nm hook and lug wrenches can be screwed in place Drive 3/8 inch Length (mm) 60 Surface Chrome-plated Ident. No. 010 58007... ● Prod. Gr. 534

Socket spanner bit ( DIN 3124 ) Hexagon, 3/8” square drive 10 DIN 3120

Application: Technical data: Socket wrench insert with hexagon and 3/8” square . Drive: 3/8 inch drive . Surface: Chrome-plated . Material: Chrome-vanadium steel Execution: . Polished

Width across fl ats 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm Length (mm) 24 24 24 24 25 26 27 28 Outer Ø (mm) 17 17 17 17 17 18 18 18 Ident. No. 060 070 080 090 100 110 120 130 58299... ● ● ● ● ● ● ● ● Width across fl ats 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm 20 mm 21 mm Length (mm) 28 30 30 30 30 30 32 32 Outer Ø (mm) 20 21 22 23 26 26 27 28 Ident. No. 140 150 160 170 180 190 200 210 58299... ● ● ● ● ● ● ● ● Width across fl ats 22 mm Length (mm) 34 Outer Ø (mm) 30 Ident. No. 220 58299... ● Prod. Gr. 582

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1265 Availability subject to country specific rules and regulations.

1263_EN_2018_KERN[21850767]-n.indd 1265 12/17/2018 3:36:00 PM Screwdrivers \ Socket wrench 3/8 inch

VDE socket spanner inserts Bi-hexagon, 3/8” square drive

Execution: Technical data: . insulation in line with DIN EN 60900 . Drive: 3/8 inch . individually tested . Surface: Plastic-coated . VDE certiﬁ ed: Yes . anti-slip drive for maximum force yield

Width across ﬂ ats 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm Ident. No. 007 008 009 010 011 012 013 014 58321... ● ● ● ● ● ● ● ● Width across ﬂ ats 16 mm 17 mm 18 mm 19 mm 20 mm 22 mm Ident. No. 016 017 018 019 020 022 58321... ● ● ● ● ● ● Prod. Gr. 531

VDE socket spanner inserts 3/8” square drive

Execution: Technical data: . insulation in line with DIN EN 60900 . Drive: 3/8 inch . individually tested . Length: 137 mm . Surface: Plastic-coated

Width across ﬂ ats XZN8 XZN10 Ident. No. 108 110 58321... ● ● Prod. Gr. 531

VDE socket spanner inserts 3/8” square drive

Execution: Technical data: . insulation in line with DIN EN 60900 . Drive: 3/8 inch . individually tested . Surface: Plastic-coated

Tip size TX20 TX25 TX30 TX40 TX45 Ident. No. 120 125 130 140 145 58321... ● ● ● ● ● Prod. Gr. 531

Socket wrench insert, long ( DIN 3124 ) Bi-hexagon, 3/8” square drive, 10, DIN 3120

Application: Socket wrench insert with bi-hexagon and 3/8” square drive. Technical data: . Drive: 3/8 inch Execution: . Width across ﬂ ats: 16 mm . Polished . Length: 61 mm . Outer diameter: 21.7 mm . Bi-hexagon with AS-drive proﬁ le . Surface: Chrome-plated Advantage: . Material: Steel, specially hardened . Excellent load capacity thanks to tough, hard HPQ steel alloy

Ident. No. 165 58332... ● Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH 1266Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1263_EN_2018_KERN[21850767]-n.indd 1266 12/17/2018 3:36:01 PM Screwdrivers \ Socket wrench 3/8 inch

Socket wrench insert with joint ( DIN 3120 ) 3/8” square drive 10, DIN 3120

Application: Articulated socket wrench insert with hexagon and 3/8” square drive for working in diﬃ cult-to-reach Technical data: areas. . Drive: 3/8 inch . Surface: Chrome-plated Advantage: . Material: Chrome-vanadium steel . Flexible bending angle Width across ﬂ ats 11 mm 18 mm Length (mm) 43 47 Outer Ø (mm) 19 24.5 Ident. No. 110 180 58342... ● ● Prod. Gr. 569 Socket wrench inserts ( DIN 3120 ) For external TORX screws, 3/8 inch square drive 10 DIN 3120

Application: Technical data: socket spanner insert for external TX screws with . Drive: 3/8 inch 3/8 inch square drive. . Surface: Chrome-plated . Material: Chrome-vanadium steel

No. 58356

No. 58358

Tip size E5 E6 E7 E8 E10 E11 E12 E14 Ident. No. 050 060 070 080 100 110 120 140 58356... ● ● ● ● ● ● ● ● 070 110 58358... Ident. No. - - ● - - ● - - HAZET = Prod. Gr. 569 a = Prod. Gr. 582

Socket wrench set For external TORX screws, 3/8 inch square drive 10 DIN 3120

Application: Advantage: set of the most common socket spanner inserts for . Excellent load capacity thanks to tough, hard HPQ external TX screws with 3/8 inch square drive steel alloy . Cadmium-free, therefore also suitable for working Execution: on titanium-alloy parts and titanium connecting . Polished elements . 7-piece Drive 3/8 inch Sockets with socket hexagon head or external TX tip provided E5 | E6 | E7 | E8 | E10 | E12 | E14 Surface Chrome-plated Material Steel, specially hardened Ident. No. 200 58362... ● Prod. Gr. 531

Screwdriver bit ( DIN 3120 ) For hexagon socket screws, 3/8” square drive, 10, DIN 3120

Application: Technical data: Screwdriver bit for hexagon socket screws with 3/8” . Drive: 3/8 inch square drive. . Surface: Chrome-plated . Material: Chrome-vanadium steel

Width across ﬂ ats 3 mm 4 mm 5 mm 6 mm 7 mm 8 mm 9 mm 10 mm 12 mm Length (mm) 47 47 47 47 47 49 50 50 50 Outer Ø (mm) 17 17 17 17 17 17 18 19 20 Ident. No. 030 040 050 060 070 080 090 100 120 58430... ● ● ● ● ● ● ● ● ● Prod. Gr. 582

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1267 Availability subject to country specific rules and regulations.

1267_EN_2018_KERN[21850772]-k.indd 1267 12/17/2018 3:35:53 PM Screwdrivers \ Socket wrench 3/8 inch Screwdriver bits For internal TORX screws, 3/8 inch square drive 10 DIN 3120

Application: screwdriver bit for internal TX screws with 3/8 inch square drive. Technical data: . Drive: 3/8 inch Execution: . Outer diameter: 17 mm . Special steel blades . Surface: Chrome-plated . Material: Chrome-vanadium steel . Steel grey

Tip size TX20 TX25 TX27 TX30 TX40 TX45 TX50 Length (mm) 43.5 43.5 43.5 43.5 43.5 43.5 44.5 Ident. No. 020 025 027 030 040 045 050 58450... ● ● ● ● ● ● ● Prod. Gr. 582

Screwdriver set For internal TORX screws, 3/8 inch square drive 10 DIN 3120

Application: Execution: set of the most common socket spanner inserts for . 8-piece internal TX screws with 3/8 inch square drive Delivery: In cardboard box with plastic inlay Drive 3/8 inch Sockets with socket hexagon head or external TX tip provided TX9 | TX10 | TX15 | TX20 | TX25 | TX27 | TX30 | TX40 Surface Chrome-plated Material Steel, specially hardened Ident. No. 200 58456... ● Prod. Gr. 531

Adapters ( DIN 3123 ) 3/8” square drive 10, DIN 3120

Application: No. 58463 020, 58464 020, 58468 020, 58472 No. 58463 010, 58464 010, 58468 010, 58472 020: For adapting a 3/8” internal square drive to a 010: For adapting a 3/8” internal square drive to a 1/2” external square drive 1/4” external square drive

No. 58463 010

Drive 3/8 inch 3/8 inch Tip size 1/4 inch 1/2 inch Surface Chrome-plated Chrome-plated Material Chrome-vanadium steel Ident. No. 010 020 58463... ● ● Chrome-vanadium steel Ident. No. 010 020 58464... ● ● 010 020 58468... Chrome-vanadium steel Ident. No. ● ● Steel, specially hardened Ident. No. 010 020 58472... ● ● GEDORE = Prod. Gr. 530 STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569 a = Prod. Gr. 582

Source: Hahn+Kolb Werkzeuge GmbH 1268Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1267_EN_2018_KERN[21850772]-k.indd 1268 12/17/2018 3:35:56 PM Screwdrivers \ Socket wrench 3/8 inch

Adapter ( DIN 3123 ) 3/8” square drive 10, DIN 3120

Application: For connecting two 3/8” internal squares Tip size 3/8 inch Surface Chrome-plated Material Chrome-vanadium steel Ident. No. 005 58464... ● Prod. Gr. 530

Bit holder ( ISO 1174 ) 3/8” square drive 10, DIN 3120

Application: Advantage: Holder for 1/4” hexagonal bits with 3/8” square . Also suitable for hexagons as per DIN 3126-E 6.3 drive (ISO 1173) with wide groove Execution: . Hexagon socket with annular pressure spring Drive 3/8 inch Bit holder 1/4 inch hexagon Surface Chrome-plated Material Chrome-vanadium steel Ident. No. 010 58474... ● Prod. Gr. 531

Extensions ( DIN 3123 ) 3/8” square drive 10, DIN 3120

Application: Execution: Extension for hand-operated socket wrench inserts . Polished with 3/8” square drive . Rigid version

Drive 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch Tip size 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch Length (mm) 50 75 125 150 250 Outer Ø (mm) 17 17 17 17 17 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Material Chrome-vanadium steel Chrome-vanadium steel Chrome-vanadium steel Chrome-vanadium steel Chrome-vanadium steel Ident. No. 010 020 030 040 050 58510... ● ● ● ● ● Prod. Gr. 582

Extension ( DIN 3123 ) 3/8” square drive 10, DIN 3120

Application: Execution: Extension for hand-operated socket wrench inserts . Rigid version with 3/8” square drive Drive 3/8 inch 3/8 inch 3/8 inch 3/8 inch Tip size 3/8 inch 3/8 inch 3/8 inch 3/8 inch Length (mm) 76 125 180 250 Outer Ø (mm) 17 17 17 17 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-vana- Chrome-vana- Chrome-vana- Chrome-vana- Material dium steel dium steel dium steel dium steel Ident. No. 005 020 025 030 58512... ● ● ● ● Prod. Gr. 530

Extensions 3/8” square drive 10, DIN 3120

Application: . Ident. No. 100: Extension for hand-operated socket wrench inserts . Flexible version with 3/8” square drive . Only suitable for clockwise tightening . Non-standard Execution: Ident. No. 005–070 . Polished Advantage: . Ident. No. 005–070: Rigid version . Ident. No. 100: Diﬃ cult-to-reach areas easier to reach with ﬂ exible version Ident. No. 100

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1269 Availability subject to country specific rules and regulations.

1269_EN_2018_KERN[21850775]-r.indd 1269 12/17/2018 3:35:55 PM Screwdrivers \ Socket wrench 3/8 inch

Drive 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch Tip size 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch Length (mm) 74 126 150 202 210 254 304 508 711 Outer Ø (mm) 18 18 18 18 17.5 18 18 18 18 Chrome- Chrome- Chrome- Chrome- Chrome- Chrome- Chrome- Chrome- Chrome- Surface plated plated plated plated plated plated plated plated plated Chrome-va- Chrome-va- Chrome-va- Chrome-va- Chrome-va- Chrome-va- Chrome-va- Chrome-va- Chrome-va- Material nadium steel nadium steel nadium steel nadium steel nadium steel nadium steel nadium steel nadium steel nadium steel Ident. No. 005 010 020 030 100 040 050 060 070 58516... ● ● ● ● ● ● ● ● ● Prod. Gr. 569

VDE extensions 3/8” square drive

Execution: . insulation in line with DIN EN 60900 . individually tested Ident. No. 110 Drive 3/8 inch 3/8 inch 3/8 inch Tip size 3/8 inch 3/8 inch 3/8 inch Length (mm) 92 175 255 VDE immer- VDE immer- VDE immer- Surface sion-insulated sion-insulated sion-insulated VDE certiﬁ ed Yes Yes Yes Ident. No. 100 110 120 58522... ● ● ● Prod. Gr. 531

Cardan joints ( DIN 3123 ) 3/8 inch square drive 10 DIN 3120

Application: Advantage: Cardan joint for screw connections with projecting . Flexible bending angle for diﬃ cult-to-reach instal- edges and conﬁ ned installation areas lation areas

Execution: No. 58530 . Polished No. 58532 Drive 3/8 inch Tip size 3/8 inch Surface Chrome-plated Length (mm) Material 46 Chrome-vanadium Ident. No. 010 58530... steel ● 46.5 Chrome-vanadium Ident. No. 010 58532... steel ● Steel, specially 010 58536... 55 hardened Ident. No. ● STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569 a = Prod. Gr. 582

Socket spanner sets With hexagon, hexagon socket and TORX inserts, 1/2 inch square drive 12.5 DIN 3120

Execution: . Bolt and nut are not damaged . Chrome-vanadium steel . Higher torques possible . Hexagon with special proﬁ le . Two-tone polyethylene foam inlay ensures any missing tools are instantly . 1/2” square drive detected . Oil and chemical-resistant foam inlay Advantage: . Optimum force transmission thanks to special proﬁ le Delivery: In powder-coated steel case with polyethylene foam inlay

Ident. No. 011 Ident. No. 021 Ident. No. 031 Ident. No. 041 19 pcs. 22 pcs. 35 pcs. 21 pcs.

Source: Hahn+Kolb Werkzeuge GmbH 1270Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1269_EN_2018_KERN[21850775]-r.indd 1270 12/17/2018 3:35:58 PM Screwdrivers \ Socket wrenches, 1/2 inch

Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch Number of pieces in assortment/set (PCS) 19 22 35 21 10 mm | 11 mm | 12 mm | 10 mm | 11 mm | 12 mm | 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 15 mm | 13 mm | 14 mm | 15 mm | 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 18 mm | Sockets with hexagon-head tip provided 16 mm | 17 mm | 19 mm | 16 mm | 17 mm | 18 mm | - 19 mm | 20 mm | 21 mm | 22 mm | 24 mm | 27 mm | 19 mm | 22 mm | 24 mm | 22 mm | 23 mm | 24 mm | 30 mm | 32 mm 27 mm | 30 mm | 32 mm 27 mm | 30 mm | 32 mm Sockets with socket hexagon-head tip - - 7 mm | 8 mm | 10 mm | - provided 12 mm | 14 mm TX20 | TX25 | TX27 | TX30 | TX40 | TX45 | TX50 | Sockets with socket hexagon head or external TX30 | TX40 | TX45 | TX55 - - TX55 | TX60 | E10 | E11 | TX tip provided | TX60 E12 | E14 | E16 | E18 | E20 | E22 | E24 Sockets with cross-head tip provided - - PH3 | PH4 - Ratchets provided 1/2-inch square 1/2-inch square 1/2-inch square 1/2-inch square Extensions provided 125 mm | 250 mm 125 mm | 250 mm 125 mm | 250 mm 125 mm | 250 mm Cross handles provided 300 mm - - - Cardan joints provided 75 mm 75 mm 75 mm - Ident. No. 011 021 031 041 58574... ● ● ● ● Prod. Gr. 582

Socket spanner sets With hexagon or bi-hexagon inserts, 1/2 inch square drive 12.5 DIN 3120

Execution: . Ident. No. 035, 060: 20 inserts, 5 operating tools . Chrome-vanadium steel . Ident. No. 045: 38 inserts, 6 operating tools . Chrome-plated Delivery: . Polished In impact-resistant plastic case, black, with PUR so foam inlay . Ident. No. 025: 13 inserts, 4 operating tools

Ident. No. 025 Ident. No. 035 Ident. No. 045 Ident. No. 060

Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch Number of pieces in assortment/set (PCS) 17 25 44 25 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 15 mm | Sockets with double hexagon-head tip 16 mm | 17 mm | 18 mm | provided - - - 19 mm | 20 mm | 21 mm | 22 mm | 23 mm | 24 mm | 26 mm | 27 mm | 28 mm | 30 mm | 32 mm 10 mm | 11 mm | 12 mm | 10 mm | 11 mm | 12 mm | 10 mm | 11 mm | 12 mm 13 mm | 14 mm | 15 mm | 13 mm | 14 mm | 15 mm | | 13 mm | 14 mm | 15 mm 16 mm | 17 mm | 18 mm | 17 mm | 19 mm | 20 mm | Sockets with hexagon-head tip provided | 17 mm | 19 mm | 22 mm 19 mm | 20 mm | 21 mm | - 21 mm | 22 mm | 23 mm | | 24 mm | 27 mm | 30 mm 22 mm | 23 mm | 24 mm | 24 mm | 26 mm | 27 mm | | 32 mm 26 mm | 27 mm | 28 mm | 28 mm | 30 mm | 32 mm 30 mm | 32 mm Sockets with socket hexagon-head tip 5 mm | 6 mm | 7 mm | 8 provided - - mm | 10 mm | 12 mm | - 14 mm Sockets with socket hexagon head or external - - TX27 | TX30 | TX40 | TX45 - TX tip provided | TX50 Sockets with cross-head tip provided - - PH1 | PH2 | PH3 | PH4 | - PZ1 | PZ2 | PZ3 | PZ4 Ratchets provided 1/2-inch square 1/2-inch square 1/2-inch square 1/2-inch square Extensions provided 125 mm | 250 mm 125 mm | 250 mm 125 mm | 250 mm 125 mm | 250 mm Cross handles provided 298 mm 298 mm 298 mm 298 mm Cardan joints provided - 70 mm 70 mm 70 mm Ident. No. 025 035 045 060 58584... ● ● ● ● Prod. Gr. 569

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1271 Availability subject to country specific rules and regulations.

1269_EN_2018_KERN[21850775]-r.indd 1271 12/17/2018 3:36:00 PM Screwdrivers \ Socket wrenches, 1/2 inch

Zyklop Speed socket wrench set 1/2” square drive 12.5 DIN 3120, 37 pieces

Execution: . Extensions with quick-action rotary sleeves and . Zyklop Speed ratchet with 1/2” square drive and Flexible-Lock system freely swivelling head with 5 speciﬁ c positions Advantage: . Pushbutton release . Robust metal case with so foam inlay and non-slip . Changes between anti-clockwise/clockwise rubber stoppers on the base for secure storage . Multi-component handle . Wobble extension enables swivelling up to 15° . Quick to change bits using the quick-action chuck Drive 1/2 inch 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | Sockets with hexagon-head tip provided 15 mm | 16 mm | 17 mm | 19 mm | 22 mm | 24 mm | 27 mm | 30 mm | 32 mm Sockets with socket hexagon-head tip provided 5 mm | 6 mm | 8 mm | 10 mm Sockets with socket hexagon head or external TX tip provided TX20 | TX25 | TX30 | TX40 | TX45 | TX50 | TX55 Sockets with cross-head tip provided PH3 | PZ3 Ratchets provided 1/2-inch square Extensions provided 52 mm | 69 mm | 125 mm | 250 mm Cross handles provided 300 mm Cardan joints provided 50 mm Bit holder provided 5/16 inch Ident. No. 020 58577... ● Prod. Gr. 542 Zyklop Speed socket wrench set 1/2” square drive 12.5 DIN 3120, 37 pieces

Execution: Technical data: . Zyklop Speed ratchet with 1/2” square drive and . Drive: 1/2 inch freely swivelling head with 5 speciﬁ c positions . Sockets with hexagon-head tip provided: 10 mm | . pushbutton release 11 mm | 12 mm | 13 mm | 14 mm | 15 mm | 16 . anti-clockwise/clockwise switch mm | 17 mm | 18 mm | 19 mm . Sockets with socket hexagon-head tip provided: 5 . multi-component handle mm | 6 mm | 8 mm | 10 mm . extensions with quick-action rotary sleeves and . Sockets with socket hexagon head or external TX Flexible-Lock system tip provided: TX20 | TX25 | TX30 | TX40 | TX45 TX50 Advantage: | . Sockets with cross-head tip provided: PH1 | PH2 | . wobble extension enables swivelling up to 15° PH3 | PZ1 | PZ2 | PZ3 . quick change of bits using the quick-change chuck . Ratchets provided: 1/2-inch square . Extensions provided: 52 mm | 250 mm Delivery: . Bit holder provided: 5/16 inch in fabric pouch with Velcro fastener

Ident. No. 025 58577... ● Prod. Gr. 542 Socket wrench set Zyklop Metal, 28 pieces 1/2 inch square drive 12.5 DIN 3120

Execution: . Ident. No. 030: Ratchet with reversing lever for . Forged all-metal ratchet with safe nut locking easy change in direction function . Ident. No. 040: Ratchet with sliding square tang . Ident. No. 030: Only 5° return angle prevents accidental switching when screwdriving . Ident. No. 040: Only 4,7° return angle Delivery: Advantage: in extremely robust yet lightweight fabric box with Velcro fastener . Extremely robust without limiting the torque Ident. No. 030 Ident. No. 040 Drive 1/2 inch 10 mm | 11 mm | 12 mm | Sockets with hexagon-head tip provided 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 19 mm Sockets with socket hexagon-head tip provided 5 mm | 6 mm | 8 mm | 10 mm Sockets with socket hexagon head or external TX tip provided TX20 | TX25 | TX27 | TX30 | TX40 | TX45 | TX50 | TX55 Sockets with cross-head tip provided PH2 | PH3 Ratchets provided 1/2-inch square Extensions provided 52 mm | 250 mm Bit holder provided 5/16 inch Reversible ratchet Ident. No. 030 58577... ● Push-through ratchet Ident. No. 040 58577... ● Prod. Gr. 542

Source: Hahn+Kolb Werkzeuge GmbH 1272Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1272_EN_2018_KERN[21850780]-q.indd 1272 12/17/2018 3:36:00 PM Screwdrivers \ Socket wrenches, 1/2 inch

Zyklop socket wrench sets with retaining function 1/2” square drive 12.5, DIN 3120

Execution: . Ident. No. 055–065: Technical data: . Ident. No. 050: . Take it easy tool ﬁ nder. with colour coding . Drive: 1/2 inch . Zyklop Hybrid ﬁ ne-toothed ratchet 1/2 inch . screws are held securely on tool square, reversing lever and nut locking function . Knurling at rear end. . return angle just 5°, 72 teeth . chromium-vanadium steel, brushed chromi- . slim head shape um-plated surface. . plug-in extension handle 270 mm . Multi-component Kra form handle Delivery: in fabric case with nut locking and Velcro closure . bracket for Hybrid extension handle on handle end

Ident. No. 050 Ident. No. 055 Ident. No. 060 Ident. No. 065

10 mm | 11 mm | 10 mm | 11 mm | Sockets with hexa- 12 mm | 13 mm | 12 mm | 13 mm | gon-head tip provided 14 mm | 15 mm | 14 mm | 15 mm | - - 16 mm | 17 mm | 16 mm | 17 mm | 18 mm | 19 mm 18 mm | 19 mm 4 mm | 5 mm | Sockets with socket hexa- 6 mm | 7 mm | gon-head tip provided - - - 8 mm | 10 mm | 12 mm | 14 mm | 17 mm TX20 | TX25 | Sockets with socket TX27 | TX30 | hexagon head or external - - TX40 | TX45 | - TX tip provided TX50 | TX55 | TX60 Ratchets provided 1/2-inch square - - - Extensions provided 250 mm - - - Ident. No. 050 055 060 065 58577... ● ● ● ● Prod. Gr. 542

Socket spanner sets With hexagon or bi-hexagon inserts, 1/2 inch square drive 12.5 DIN 3120

Execution: Delivery: . Chrome-vanadium steel 31CrV3 In metal case

Ident. No. 016 Ident. No. 026 Ident. No. 071 Ident. No. 120

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1273 Availability subject to country specific rules and regulations.

1272_EN_2018_KERN[21850780]-q.indd 1273 12/17/2018 3:36:05 PM Screwdrivers \ Socket wrenches, 1/2 inch

Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch | 1/4 inch Number of pieces in assortment/set (PCS) 23 13 28 50 10 mm | 12 mm | 13 mm | Sockets with double hexagon-head tip - 14 mm | 15 mm | 16 mm | - - provided 17 mm | 18 mm | 19 mm | 22 mm | 24 mm 10 mm | 11 mm | 12 mm 4 mm | 4.5 mm | 5 mm | 8 mm | 9 mm | 10 mm | 11 | 13 mm | 14 mm | 15 mm 5.5 mm | 6 mm | 7 mm | 8 mm | 12 mm | 13 mm | 14 | 16 mm | 17 mm | 18 mm mm | 9 mm | 10 mm | 11 mm | 15 mm | 16 mm | 17 | 19 mm | 21 mm | 22 mm Sockets with hexagon-head tip provided - mm | 12 mm | 13 mm | 14 mm | 18 mm | 19 mm | 21 | 23 mm | 24 mm | 26 mm mm | 15 mm | 17 mm | 19 mm | 22 mm | 24 mm | 27 | 27 mm | 28 mm | 30 mm mm | 22 mm | 24 mm | 27 mm | 30 mm | 32 mm | 32 mm | 33 mm | 34 mm mm | 30 mm | 36 mm Sockets with socket hexagon-head tip 3 mm | 4 mm | 5 mm | 6 provided - - - mm | 7 mm | 8 mm | 10 mm | 12 mm | 14 mm Sockets with cross-head tip provided - - - PH1 | PH2 | PH3 0.8 x 4 mm | 1 x 5.5 mm | Sockets with slotted tip provided - - - 1.2 x 6.5 mm | 1.2 x 8 mm | 1.6 x 10 mm Ratchets provided 1/2-inch square 1/2-inch square 1/2-inch square 1/4-inch square | 1/2-inch square 55 mm | 97 mm | 125 mm Extensions provided 125 mm | 250 mm 125 mm 125 mm | 250 mm | 250 mm Cross handles provided 292 mm - 292 mm 292 mm Cardan joints provided 73 mm - 73 mm 38 mm | 73 mm External dimensions of box 320 x 210 x 55 mm 281 x 79 x 48 mm 433 x 180 x 48 mm 525 x 203 x 50 mm Ident. No. 016 026 071 120 58580... ● ● ● ● Prod. Gr. 530

Socket wrench set 1/2”, 3/8” and 1/4” square drive 12.5/10/6.3 DIN 3120

Execution: Delivery: . HPQ heavy-duty steel in robust, stackable ABS plastic storage box . Chrome-plated . Polished

Drive 1/4 inch | 3/8 inch | 1/2 inch TX8 | TX9 | TX10 | TX15 | TX20 | TX25 | Sockets with socket hexagon head or external TX tip provided TX27 | TX30 | TX40 | TX45 | TX50 | TX55 | TX60 | E4 | E5 | E6 | E7 | E8 | E10 | E11 | E12 | E14 | E16 | E18 | E20 | E24 Bit holder provided 1/4 inch Ident. No. 401 58588... ● Prod. Gr. 531

Socket spanner sets With hexagon inserts, 1/2 inch square drive 12.5 DIN 3120

Execution: . Ident. No. 307: . HPQ heavy-duty steel . 16 inserts, 6 operating tools . Chrome-plated . With QuickRelease safety lock . Polished Delivery: . Ident. No. 302: 12 inserts, 3 operating tools in robust, stackable ABS plastic storage box Drive 1/2 inch 1/2 inch Ident. No. 302 Ident. No. 307 10 mm | 11 mm | 12 mm | 10 mm | 13 mm | 16 mm | 13 mm | 14 mm | 15 mm | Sockets with hexagon-head tip provided 17 mm | 18 mm | 19 mm | 16 mm | 17 mm | 18 mm | 21 mm | 22 mm | 24 mm | 19 mm | 21 mm | 22 mm | 27 mm | 30 mm | 32 mm 24 mm | 27 mm | 30 mm | 32 mm Ratchets provided 1/2-inch square 1/2-inch square Extensions provided 130 mm | 255 mm 75 mm | 130 mm | 255 mm Cross handles provided - 300 mm Cardan joints provided - 71 mm External dimensions of box 405 x 178 x 54 mm 440 x 185 x 55 mm Ident. No. 302 307 58588... ● ● Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH 1274Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1272_EN_2018_KERN[21850780]-q.indd 1274 12/17/2018 3:36:06 PM Screwdrivers \ Socket wrenches, 1/2 inch

Socket spanner sets With bi-hexagon inserts, 1/2 inch-square drive 12.5 DIN 3120

Execution: . Ident. No. 341: . Ident. No. 316: 22 inserts, 6 operating tools . HPQ steel . Ident. No. 316–336, 350: . chromium-plated . HPQ heavy-duty steel . polished . Chrome-plated . 17 inserts in imperial sizes, 6 actuating tools . Polished . Ident. No. 350: 39 inserts, 6 operating tools . Ident. No. 321: 28 inserts, 13 combination wrenches, 6 operating tools Delivery: . Ident. No. 336: 25 inserts, 6 operating tools Ident. No. 316–336: in robust, stackable ABS plastic storage box

Ident. No. 350 Ident. No. 316 Ident. No. 321 Ident. No. 336

Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 15 mm | 16 mm | 17 mm | 18 mm | 19 mm | 20 mm | 21 mm | 22 8 mm | 9 mm | 10 mm 3/8 inch | 7/16 inch | mm | 23 mm | 24 mm 8 mm | 9 mm | 10 mm | 11 mm | 12 mm | 13 8 mm | 10 mm | 11 1/2 inch | 9/16 inch | | 25 mm | 26 mm | | 11 mm | 12 mm | 13 mm | 14 mm | 15 mm mm | 12 mm | 13 mm 19/32 inch | 5/8 inch 27 mm | 28 mm | 30 mm | 14 mm | 15 mm | 16 mm | 17 mm | 18 | 14 mm | 15 mm | 16 | 11/16 inch | 3/4 mm | 32 mm | 34 mm Sockets with double hexagon-head tip | 16 mm | 17 mm | 18 mm | 19 mm | 20 mm mm | 17 mm | 18 mm inch | 25/32 inch | | 3/8 inch | 7/16 inch provided mm | 19 mm | 21 mm | 21 mm | 22 mm | 23 | 19 mm | 21 mm | 22 13/16 inch | 7/8 inch | 1/2 inch | 9/16 inch | 22 mm | 24 mm | 27 mm | 24 mm | 26 mm mm | 24 mm | 27 mm | 15/16 inch | 1 1/16 | 19/32 inch | 5/8 mm | 30 mm | 32 mm | 27 mm | 28 mm | 30 | 30 mm | 32 mm inch | 1 1/8 inch | 1 inch | 11/16 inch | | 34 mm mm | 32 mm 3/16 inch | 1 1/4 inch 3/4 inch | 25/32 inch | 13/16 inch | 7/8 inch | 15/16 inch | 1 inch | 1 1/16 inch | 1 1/8 inch | 1 3/16 inch | 1 1/4 inch Long sockets with double hexagon-head tip provided - 16 mm | 20.8 mm - - - Sockets with socket hexagon-head tip 4 mm | 5 mm | 6 mm | 12 mm | 10 mm | 8 provided - 7 mm | 8 mm | 10 mm mm | 7 mm | 6 mm | 5 - - | 12 mm mm | 4 mm 10 mm, 11 mm, 12 mm, 13 mm, 14 mm, Composition of set - 15 mm, 16 mm, 17 - - - mm, 18 mm, 19 mm, 21 mm, 22 mm, 24 mm Ratchets provided 1/2-inch square 1/2-inch square 1/2-inch square 1/2-inch square 1/2-inch square Extensions provided 75 mm | 130 mm | 75 mm | 130 mm | 75 mm | 130 mm | 52 mm | 130 mm | 75 mm | 130 mm | 255 mm 255 mm 255 mm 255 mm 255 mm Cross handles provided 300 mm 300 mm 300 mm 300 mm 300 mm Cardan joints provided 71 mm 71 mm 71 mm 71 mm 71 mm External dimensions of box 446 x 205 x 54 mm 470 x 234 x 74 mm 470 x 234 x 74 mm - 530 x 265 x 50 mm Ident. No. 316 321 336 341 350 58588... ● ● ● ● ● Prod. Gr. 531 Socket spanner sets With hexagon inserts, 1/2 inch square drive 12.5 DIN 3120

Execution: . Ident. No. 050: 19 inserts, 5 operating tools . Chrome-vanadium steel Delivery: . Matt chromium-plated In painted metal case . Ident. No. 010: 11 inserts, 2 operating tools

Drive 1/2 inch 1/2 inch Ident. No. 050 Number of pieces in assortment/set (PCS) 13 24 Ident. No. 010 8 mm | 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 8 mm | 10 mm | 11 mm | 12 15 mm | 16 mm | 17 mm | mm | 13 mm | 14 mm | 15 Sockets with hexagon-head tip provided 19 mm | 21 mm | 22 mm | mm | 16 mm | 17 mm | 19 23 mm | 24 mm | 26 mm | mm | 22 mm 27 mm | 28 mm | 30 mm | 32 mm Ratchets provided 1/2-inch square 1/2-inch square Extensions provided 125 mm 125 mm | 250 mm Cardan joints provided - 70 mm External dimensions of box 320 x 150 x 50 mm 450 x 200 x 50 mm Ident. No. 010 050 58575... ● ● Prod. Gr. 526

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1275 Availability subject to country specific rules and regulations.

1275_EN_2018_KERN[21850785]-a.indd 1275 12/17/2018 3:35:56 PM Screwdrivers \ Socket wrenches, 1/2 inch

Socket spanner sets With hexagon inserts, 1/2 inch square drive 12.5 DIN 3120

Execution: Advantage: . Chrome-vanadium steel . High-quality insertion tools to robust, long-lasting . Ident. No. 200: Ratchet with 2-component handle industry-standard speciﬁ cation and locking button . Individual parts are securely stored and trans- . Ident. No. 300: Hexagon socket driver lengths: 55, ported using clamping function 100, 140 and 200 mm . Any missing tools are instantly detected thanks to size-related tool recesses Ident. No. 300 Drive 1/2 inch 1/2 inch Number of pieces in assortment/set (PCS) 25 30 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 15 mm | Ident. No. 200 Sockets with hexagon-head tip provided 16 mm | 17 mm | 18 mm | - 19 mm | 20 mm | 21 mm | 22 mm | 23 mm | 24 mm | 27 mm | 30 mm | 32 mm Long sockets with hexagon-head tip provided 16 mm | 21 mm - 5 mm | 6 mm | 7 mm | 8 mm Sockets with socket hexagon-head tip provided - | 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 17 mm | 19 mm Ratchets provided 1/2-inch square - Extensions provided 125 mm | 250 mm - Cross handles provided 300 mm - Cardan joints provided 70 mm - Ident. No. 200 300 58575... ● ● Prod. Gr. 526 Pass-through socket spanner sets

Application: . 5° return angle Flexible screwing, even of long projecting bolts (e.g. . Two-component handle threaded rods) . Ident. No. 100: . 12 inserts Execution: . 2 operating tools . Chrome-vanadium steel . Ident. No. 110: 53 pcs . Matt chromium-plated . Sliding ratchet with ﬂ exible head Delivery: . Finely serrated with 72 teeth High-density polyethylene case (HDPE) Ident. No. 100 Ident. No. 110 Drive 1/2 inch 1/2 inch 10 mm | 11 mm | 12 mm | 10 mm | 11 mm | 12 mm | 13 mm | 14 mm | 15 mm | 13 mm | 14 mm | 15 mm | Sockets with hexagon-head tip provided 16 mm | 17 mm | 18 mm | 16 mm | 17 mm | 19 mm | 19 mm | 21 mm | 22 mm | 21 mm | 22 mm | 24 mm 24 mm Sockets with socket hexagon-head tip provided - 5 mm | 6 mm | 7 mm | 8 mm | 10 mm | 12 mm TX20 | TX25 | TX27 | TX30 | Sockets with socket hexagon head or external - TX40 | TX45 | TX50 | TX55 | TX tip provided E8 | E10 | E11 | E12 | E14 | E16 | E18 | E20 | E22 Extensions provided 75 mm 75 mm Bit holder provided - 1/4 inch Ident. No. 100 110 58575... ● ● Prod. Gr. 519 Reversible ratchets: ﬁ ne-tooth ratchet and telescopic ratchet reversible 1/2 inch square drive, 12.5, DIN 3120

Application: . Finely serrated Ident. No. 010, 070: Ratchet for hand-operated . Ident. No. 060: socket wrench inserts and connection parts with . telescopic function: can be extended from 305 Ident. No. 010 Ident. No. 060–070 1/2” square drive. to 445 mm Ident. No. 060: ratchet for hand-operated socket . ratcheting/clamping function wrench inserts and connection parts with 1/2” . anti-clockwise and clockwise rotation possible square drive. using reversing lever with locking button . ﬁ n e l y s e r r a t e d Execution: . Ident. No. 070: . Ident. No. 010: With hanging eyelet . Telescopic function: Can be extended from 457 . Ident. No. 010, 070: to 600 mm . Anti-clockwise and clockwise rotation possible . Ratcheting/clamping function using reversing lever with locking button Tip size 1/2 inch 1/2 inch 1/2 inch Length (mm) 255 445 600 Number of teeth (PCS) 72 72 72 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-vanadium Chrome-vanadium Chrome-vanadium Material steel steel steel Material of the grip handle 2-component plastic 2-component plastic 2-component plastic Ident. No. 010 060 070 58576... ● ● ● Prod. Gr. 582 Source: Hahn+Kolb Werkzeuge GmbH 1276Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1275_EN_2018_KERN[21850785]-a.indd 1276 12/17/2018 3:35:59 PM Screwdrivers \ Socket wrenches, 1/2 inch

Zyklop Speed, Zyklop Hybrid and Zyklop Metal ratchets 1/2 inch square drive 12.5 DIN 3120

Execution: . Ident. No. 110: Ratchet with reversing lever for easy change in direction . Ident. No. 100: . Ident. No. 110–120: Extremely robust without limiting the torque . Freely swivellable ratchet head with 5 deﬁ ned positions at 0°,15° and 90°, . Ident. No. 120: Ratchet with sliding square tang prevents accidental switching le and right when screwdriving . Flywheel design with quick-action rotary sleeve . Pushbutton release Technical data: . Anti-clockwise/clockwise rotation can be switched using knurling wheel . Tip size: 1/2 inch . Ident. No. 110–120: Forged all-metal ratchet with safe nut locking function . Surface: Chrome-plated . Material: Chrome-vanadium steel Advantage: . Ident. No. 100: Ergonomic power grip for fatigue-free work

Ident. No. 100

Ident. No. 110 Ident. No. 120

Length (mm) 277 281 281 Number of teeth (PCS) 72 72 76 Returning angle (Degree) 5 5 4.7 Ident. No. 100 110 120 58577... ● ● ● Prod. Gr. 542 Ratchets Reversible 1/2 inch square drive, 12.5, DIN 3120

Execution: . Ident. No. 060: Long reversible ratchet, with pushbutton release . Ident. No. 010: Push-through square drive with ball lock . Ident. No. 070: Reversing lever and pushbutton release, extra-slim head . Ident. No. 020: With metal disc reversing Advantage: . Ident. No. 040: Deeper-set reversing lever and pushbutton release . Comfortable and good grip thanks to non-slip handle

Ident. No. 070 Ident. No. 010 Ident. No. 040 Ident. No. 020 Ident. No. 060

Tip size 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch Length (mm) 270 271 270 350 272 Number of teeth (PCS) 24 72 32 32 72 Returning angle (Degree) 7.5 - - - - Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Material Chrome-vanadium steel Chrome-vanadium steel Chrome-vanadium steel Chrome-vanadium steel Chrome-vanadium steel Ident. No. 010 020 040 060 070 58886... ● ● ● ● ● Prod. Gr. 530 Ratchets Reversible 1/2 inch square drive, 12.5, DIN 3120

Execution: . Ident. No. 080: . Ident. No. 030: Reversible ratchet with deeper-set reversing lever . Reversible ratchet with swivel head . Ident. No. 050: Short reversible ratchet with deeper-set reversing lever . Can be swivelled through 180° . Ident. No. 060: Reversible ratchet can be continuously extended from 410 to 590 mm, with locking ring Technical data: . Tip size: 1/2 inch . Ident. No. 065: extra-long version . Surface: Chrome-plated . Ident. No. 070: . Material: Chrome-vanadium steel . Reversible ratchet with deeper-set disc reversing . Material of the grip handle: 2-component plastic . Finely toothed

Ident. No. 060 Ident. No. 065 Ident. No. 030–050 Ident. No. 070 Ident. No. 080

Length (mm) 275 199 590 389 245 270 Number of teeth (PCS) 32 32 32 32 72 32 Returning angle (Degree) 11.25 11.25 11.25 11.25 5 11.25 Ident. No. 030 050 060 065 070 080 58890... ● ● ● ● ● ● Prod. Gr. 569

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1277 Availability subject to country specific rules and regulations.

1277_EN_2018_KERN[21850788]-v.indd 1277 12/17/2018 3:35:57 PM Screwdrivers \ Socket wrenches, 1/2 inch

Ratchets Reversible 1/2 inch square drive, 12.5, DIN 3120

Execution: Technical data: . Chrome-alloy steel . Tip size: 1/2 inch . Ident. No. 010: With metal disc reversing . Surface: Chrome-plated . Material: Steel, specially hardened . Ident. No. 020–061: Anti-clockwise/clockwise rotation using reversing lever . Material of the grip handle: 2-component plastic . Ident. No. 030: Long version . Ident. No. 061: With QuickRelease safety lock

Ident. No. 030 Ident. No. 020 Ident. No. 061 Ident. No. 010

Length (mm) 265 266 380 265 Number of teeth (PCS) 60 36 36 80 Returning angle (Degree) - - - 4.5 Ident. No. 010 020 030 061 58894... ● ● ● ● Prod. Gr. 531 VDE ratchet 1/2” square drive

Execution: . QuickRelease technology prevents uncontrolled . ﬁ ne-tooth ratchet with 80 teeth for particularly low release of the tools working angle of just 4.5° . individually tested DIN EN 60900 . socket sits precisely with minimum play on the square Tip size 1/2 inch Length (mm) 270 Surface VDE immer- sion-insulated VDE certiﬁ ed Yes Ident. No. 150 58894... ● Prod. Gr. 531 Ratchet Reversible, 1/2” square drive, 12.5, DIN 3120

Execution: . Anti-clockwise and clockwise rotation possible using reversing lever with locking button

Tip size 1/2 inch Length (mm) 250 Number of teeth (PCS) 72 Surface Chrome-plated Material Chrome-vanadium steel Material of the grip handle 2-component plastic Ident. No. 500 58899... ● Prod. Gr. 526

T-handles ( DIN 3122 ) 1/2” square drive 12.5, DIN 3120

Application: Execution: T-handle for hand-operated socket wrench inserts . No. 58794: Movable sliding head and connection parts with 1/2” square drive. . No. 58804–58808: Polished No. 58794 Tip size 1/2 inch Surface Chrome-plated Length (mm) Material 300 Chrome-vana- Ident. No. 010 58794... dium steel ● 292 Chrome-vana- Ident. No. 010 58800... dium steel ● 298 Chrome-vana- Ident. No. 010 58804... dium steel ● 300 Steel, specially Ident. No. 010 58808... hardened ● GEDORE = Prod. Gr. 530 STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569 a = Prod. Gr. 582

Source: Hahn+Kolb Werkzeuge GmbH 1278Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1277_EN_2018_KERN[21850788]-v.indd 1278 12/17/2018 3:35:59 PM Screwdrivers \ Socket wrenches, 1/2 inch

Multi-angle ratchets ( DIN 3122 ) 1/2” square drive 12.5, DIN 3120

Application: Execution: Jointed handle for hand-operated socket wrench inserts and connection parts . Polished with 1/2” square drive. . No. 58840 030: Made from chrome alloy steel

No. 58840 030 No. 58836 010 No. 58836 020

Length (mm) 396 472 397 469 Chrome-vana- Chrome-vana- Steel, specially Steel, specially Material dium steel dium steel hardened hardened Tip size Surface 58836... 58836... 58840... 58840... Ident. No. Ident. No. Ident. No. Ident. No. 1/2 inch Chrome-plated 010 ● 020 ● 020 ● 030 ● STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569 Socket wrench bit ( DIN 3124 ) Hexagon, 1/2” square drive, 12.5, DIN 3120

Technical data: . Drive: 1/2 inch . Surface: Chrome-plated . Material: Chrome-vanadium steel

Width across ﬂ ats 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm 15 mm

Length (mm) 38 38 38 38 38 38 38 38 Outer Ø (mm) 22 22 22 22 22 22 22 23 Ident. No. 080 090 100 110 120 130 140 150 58590... ● ● ● ● ● ● ● ● Width across ﬂ ats 16 mm 17 mm 18 mm 19 mm 20 mm 21 mm 22 mm 23 mm Length (mm) 38 38 38 38 38 38 42 42 Outer Ø (mm) 24 25 25 27 28 29 30 30 Ident. No. 160 170 180 190 200 210 220 230 58590... ● ● ● ● ● ● ● ● Width across ﬂ ats 24 mm 26 mm 27 mm 28 mm 30 mm 32 mm Length (mm) 42 42 45 45 45 47 Outer Ø (mm) 32 34 36 38 39 42 Ident. No. 240 260 270 280 300 320 58590... ● ● ● ● ● ● Prod. Gr. 582

Socket wrench bit ( DIN 3124 ) Hexagon, 1/2” square drive, 12.5, DIN 3120

Execution: Technical data: . HPQ heavy-duty steel . Drive: 1/2 inch . Tip proﬁ le type: AS drive proﬁ le Advantage: . Surface: Chrome-plated . Excellent load capacity thanks to tough, hard HPQ . Material: Steel, specially hardened steel alloy

Width across fl ats 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm 15 mm Length (mm) 38 38 38 38 38 38 38 38 Outer Ø (mm) 22 22 22 22 22 22 22.7 22.7 Ident. No. 080 090 100 110 120 130 140 150 58604... ● ● ● ● ● ● ● ● Width across fl ats 16 mm 17 mm 18 mm 19 mm 20 mm 21 mm 22 mm 23 mm Length (mm) 38 38 38 38 42 42 42 42 Outer Ø (mm) 23.7 24 24.7 26.2 27.2 28.7 29.7 30.7 Ident. No. 160 170 180 190 200 210 220 230 58604... ● ● ● ● ● ● ● ● Width across fl ats 24 mm 25 mm 26 mm 27 mm 28 mm 30 mm 32 mm 34 mm Length (mm) 42 42 42 45 45 45 47 47 Outer Ø (mm) 32 33.2 34.4 36.2 37.4 39.7 42.2 45 Ident. No. 240 250 260 270 280 300 320 340 58604... ● ● ● ● ● ● ● ● Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1279 Availability subject to country specific rules and regulations.

1279_EN_2018_KERN[21850791]-10.indd 1279 12/17/2018 3:35:53 PM Screwdrivers \ Socket wrenches, 1/2 inch

VDE socket wrench insert Bi-hexagon, 1/2” square drive, 12.5, DIN 3120

Execution: . insulation in line with DIN EN 60900 . individually tested . anti-slip drive for maximum force yield

Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch Width across fl ats 10 mm 11 mm 12 mm 13 mm 14 mm 17 mm 19 mm 22 mm VDE immer- VDE immer- VDE immer- VDE immer- VDE immer- VDE immer- VDE immer- VDE immer- Surface sion-insulated sion-insulated sion-insulated sion-insulated sion-insulated sion-insulated sion-insulated sion-insulated Chrome-vana- Chrome-vana- Chrome-vana- Chrome-vana- Chrome-vana- Chrome-vana- Chrome-vana- Chrome-vana- Material dium steel dium steel dium steel dium steel dium steel dium steel dium steel dium steel VDE certifi ed Yes Yes Yes Yes Yes Yes Yes Yes Ident. No. 010 011 012 013 014 017 019 022 58621... ● ● ● ● ● ● ● ● Drive 1/2 inch Width across fl ats 24 mm VDE immer- Surface sion-insulated Chrome-vana- Material dium steel VDE certifi ed Yes Ident. No. 024 58621... ● Prod. Gr. 531

Socket wrench bit ( DIN 3124 ) Long version, bi-hexagon, 1/2” square drive, 12.5, DIN 3120

Application: Technical data: Socket wrench insert with bi-hexagon and 1/2” . Drive: 1/2 inch square drive . Surface: Chrome-plated . Material: Chrome-vanadium steel Execution: . Long version

Width across fl ats 10 mm 11 mm 12 mm 13 mm 14 mm 15 mm 16 mm 17 mm Length (mm) 77 77 77 77 77 77 77 77 Outer Ø (mm) 22.5 22.5 22.5 22.5 22.5 22.5 24 23 Ident. No. 100 110 120 130 140 150 160 170 58627... ● ● ● ● ● ● ● ● Width across fl ats 18 mm 19 mm 20 mm 21 mm 22 mm 24 mm 26 mm 27 mm Length (mm) 82 82 82 82 82 82 82 82 Outer Ø (mm) 24 25 30 30 31 32 34 37 Ident. No. 180 190 200 210 220 240 260 270 58627... ● ● ● ● ● ● ● ● Width across fl ats 30 mm 32 mm Length (mm) 82 82 Outer Ø (mm) 41 42 Ident. No. 300 320 58627... ● ● Prod. Gr. 582

Source: Hahn+Kolb Werkzeuge GmbH 1280Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1279_EN_2018_KERN[21850791]-10.indd 1280 12/17/2018 3:35:55 PM Screwdrivers \ Socket wrenches, 1/2 inch

Socket wrench bit ( DIN 3124 ) Long version, bi-hexagon, 1/2” square drive, 12.5, DIN 3120

Application: . High force transmission to the edges of the bolts Socket wrench insert with bi-hexagon and 1/2” and nuts for optimum load distribution square drive . Longer bolt and nut service lives . ref. no. 208 — with rubber insert for holding spark Execution: plugs . HPQ heavy-duty steel . Long version Technical data: . Drive: 1/2 inch Advantage: . Tip proﬁ le type: AS drive proﬁ le . Excellent load capacity thanks to tough, hard HPQ . Surface: Chrome-plated steel alloy . Material: Steel, specially hardened . Cadmium-free, therefore also suitable for working on titanium-alloy parts and titanium connecting elements

Width across ﬂ ats 10 mm 13 mm 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm Length (mm) 83 83 83 83 89 83 83 83 Outer Ø (mm) 22 22 22.7 22.7 23.7 24 24.7 26.2 Ident. No. 100 130 140 150 160 170 180 190 58652... ● ● ● ● ● ● ● ● Width across ﬂ ats 20.8 mm 21 mm 22 mm 24 mm 27 mm 30 mm 32 mm Length (mm) 83 83 83 83 83 83 83 Outer Ø (mm) 27.7 28.7 29.7 32 36.2 39.7 42.4 Ident. No. 208 210 220 240 270 300 320 58652... ● ● ● ● ● ● ● Prod. Gr. 531

Socket wrench bit For external TORX screws, 1/2” square drive, 12.5, DIN 3120

Application: Advantage: socket spanner insert for external TX screws with . Good grip thanks to knurling 1/2 inch square drive Technical data: Execution: . Drive: 1/2 inch . Knurled . Surface: Chrome-plated . Material: Chrome-vanadium steel

Tip size E10 E11 E12 E14 E16 E18 E20 E22 E24 Length (mm) 38 38 38 38 38 38 38 38 41 Outer Ø (mm) 22 22 22 22 22 27 27 27 28.5 Ident. No. 010 011 012 014 016 018 020 022 024 58662... ● ● ● ● ● ● ● ● ● Prod. Gr. 582

Screwdriver bit For slotted screws, 1/2” square drive 12.5 DIN 3120

Execution: Technical data: . With ball-securing groove . Drive: 1/2 inch . Burnished tips . Length: 60 mm . Surface: Chrome-plated Advantage: . Material: Chrome-vanadium steel . Improved resistance to corrosion thanks to burnishing process

Thickness of cutting edge (mm) 1.2 1.6 2.0 2.5 Width of cutting edge (mm) 8.0 10.0 12.0 14.0 Ident. No. 010 015 030 040 58674... ● ● ● ● Prod. Gr. 582

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1281 Availability subject to country specific rules and regulations.

1281_EN_2018_KERN[21850794]-p.indd 1281 12/17/2018 3:35:54 PM Screwdrivers \ Socket wrenches, 1/2 inch

Screwdriver bits For Phillips screws

Technical data: . Drive: 1/2 inch . Length: 60 mm . Surface: Chrome-plated . Material: Chrome-vanadium steel

Ident. No. 020–040 Tip size PH2 PH3 PH4 PZ2 PZ3 PZ4 Ident. No. 020 030 040 120 130 140 58678... ● ● ● ● ● ● Prod. Gr. 582

Screwdriver bit For hexagon socket screws, 1/2 inch square drive 12.5 DIN 3120

Application: Advantage: Screwdriver bit for hexagon socket screws with 1/2” . Improved resistance to corrosion thanks to square drive burnishing process

Execution: Technical data: . Short version . Drive: 1/2 inch . Burnished drive . Length: 55 mm . Outer diameter: 25 mm . Surface: Chrome-plated . Material: Chrome-vanadium steel

Width across ﬂ ats 4 mm 5 mm 6 mm 7 mm 8 mm 9 mm 10 mm 12 mm 14 mm 17 mm 19 mm Ident. No. 040 050 060 070 080 090 100 120 140 170 190 58682... ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 582

Screwdriver inserts For hexagon socket screws, 1/2 inch square drive 12.5 DIN 3120

Application: . High level of corrosion protection Screwdriver bit for hexagon socket screws with 1/2” square drive . Good grip thanks to knurling

Execution: Technical data: . With pressed-in, manganese phosphate hexagon pin made from vanadium . Drive: 1/2 inch special steel 50CrV4 . Surface: Chrome-plated . Cross-knurling . Material: Chrome-vanadium steel Advantage: . Longer service lives thanks to manganese phosphate plating

Ident. No. 250–340 Long version Ident. No. 040–090 Ident. No. 100–190

Version Short Short Short Short Short Short Short Short Width across fl ats 4 mm 5 mm 6 mm 7 mm 8 mm 9 mm 10 mm 12 mm Length (mm) 60 60 60 60 60 60 60 60 Outer Ø (mm) 22.5 22.5 22.5 22.5 22.5 22.5 22.5 23 Ident. No. 040 050 060 070 080 090 100 120 58688... ● ● ● ● ● ● ● ● Version Short Short Short Long Long Long Long Long Width across fl ats 14 mm 17 mm 19 mm 5 mm 6 mm 7 mm 8 mm 8 mm Length (mm) 60 60 60 180 90 100 90 120 Outer Ø (mm) 24.7 28 27 22.5 22.5 22.5 22.5 22.5 Ident. No. 140 170 190 250 260 270 275 280 58688... ● ● ● ● ● ● ● ● Version Long Long Long Width across fl ats 10 mm 12 mm 14 mm Length (mm) 140 140 140 Outer Ø (mm) 22.5 23 24.7 Ident. No. 300 320 340 58688... ● ● ● Prod. Gr. 530

Source: Hahn+Kolb Werkzeuge GmbH 1282Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1281_EN_2018_KERN[21850794]-p.indd 1282 12/17/2018 3:35:56 PM Screwdrivers \ Socket wrenches, 1/2 inch

Screwdriver inserts For hexagon socket screws, 1/2 inch square drive 12.5 DIN 3120

Application: Technical data: Screwdriver bit for hexagon socket screws with 1/2” . Drive: 1/2 inch square drive . Surface: Chrome-plated . Material: Steel, specially hardened Execution: Ident. No. 040–190 . Chrome-alloy steel

Ident. No. 250–280 Version Short Short Short Short Short Short Short Short Width across ﬂ ats 4 mm 5 mm 6 mm 7 mm 8 mm 10 mm 12 mm 14 mm Length (mm) 60 60 60 60 60 60 60 60 Outer Ø (mm) 22.7 22.7 22.7 22.7 22.7 22.7 23.7 23.7 Ident. No. 040 050 060 070 080 100 120 140 58696... ● ● ● ● ● ● ● ● Version Short Short Long Long Long Long Long Width across ﬂ ats 17 mm 19 mm 5 mm 6 mm 7 mm 8 mm 8 mm Length (mm) 60 60 180 220 100 80 140 Outer Ø (mm) 27.5 31 22 22.7 22 22.7 22.7 Ident. No. 170 190 250 262 270 273 280 58696... ● ● ● ● ● ● ● Prod. Gr. 531

Screwdriver insert sets For hexagon socket screws, 1/2 inch square drive 12.5 DIN 3120

Application: Execution: Ident. No. 300: Selection of various screwdriver bits . Chrome-vanadium steel for hexagon socket screws with 1/2” square drive . Short version Ident. No. 310: Selection of various screwdriver bits . Ident. No. 310: With reversible lever and 1/2” for hexagon socket screws and operating tools with extension 1/2” square drive Delivery: In metal case with so foam inlay Ident. No. 310 Ident. No. 300 Drive 1/2 inch 1/2 inch Number of pieces in assortment/set (PCS) 9 11 5 mm | 6 mm | 7 mm | 8 mm 5 mm | 6 mm | 7 mm | 8 mm Sockets with socket hexagon-head tip provided | 9 mm | 10 mm | 12 mm | | 9 mm | 10 mm | 12 mm | 14 mm | 17 mm 14 mm | 17 mm Ratchets provided - 1/2-inch square Extensions provided - 250 mm Ident. No. 300 310 58682... ● ● Prod. Gr. 582

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1283 Availability subject to country specific rules and regulations.

1281_EN_2018_KERN[21850794]-p.indd 1283 12/17/2018 3:35:58 PM Screwdrivers \ Socket wrenches, 1/2 inch

Screwdriver insert sets For hexagon socket screws, 1/2 inch square drive 12.5 DIN 3120

Application: Execution: Ident. No. 600: Selection of various screwdriver bits . Chrome-vanadium steel 31CrV3 for hexagon socket screws with 1/2” square drive . Short version Ident. No. 610: Selection of various screwdriver bits . Ident. No. 610: With reversible lever and 1/2” for hexagon socket screws and operating tools with extension 1/2” square drive Ident. No. 600 Delivery: In metal case Drive 1/2 inch 1/2 inch Number of pieces in assortment/set (PCS) 9 11 Ident. No. 610 5 mm | 6 mm | 7 mm | 8 mm 5 mm | 6 mm | 7 mm | 8 mm Sockets with socket hexagon-head tip provided | 9 mm | 10 mm | 12 mm | | 9 mm | 10 mm | 12 mm | 14 mm | 17 mm 14 mm | 17 mm Ratchets provided - 1/2-inch square Extensions provided - 175 mm Ident. No. 600 610 58688... ● ● Prod. Gr. 530 Screwdriver set For hexagon socket screws, 1/2 inch square drive 12.5 DIN 3120

Application: Execution: Selection of various screwdriver bits for hexagon . Chrome-alloy steel socket screws with 1/2” square drive Delivery: in robust, stackable ABS plastic storage box Drive 1/2 inch Number of pieces in assortment/set (PCS) 10 Sockets with socket hexagon-head tip provided 4 mm | 5 mm | 6 mm | 7 mm | 8 mm | 10 mm | 12 mm | 14 mm | 17 mm | 19 mm Ident. No. 501 58696... ● Prod. Gr. 531

Screwdriver bit For hexagon socket screws with guide spigot RIBE-CS and according to DIN 6912 with 1/2” square drive 12.5 DIN 3120

Execution: Technical data: . Chrome-alloy steel . Drive: 1/2 inch . Knurled . Length: 60 mm . Surface: Chrome-plated . Material: Steel, specially hardened

Tip size RIBE-CS 5 RIBE-CS 6 RIBE-CS 8 RIBE-CS 10 RIBE-CS 12 RIBE-CS 14 Outer Ø (mm) 22.7 22.7 22.7 22.7 23.7 23.7 Ident. No. 050 060 080 100 120 140 58712... ● ● ● ● ● ● Prod. Gr. 531

Screwdriver bit For serrated socket screws XZN, 1/2” square drive, 12.5, DIN 3120

Execution: Technical data: . Chrome-alloy steel . Drive: 1/2 inch . Knurled . Length: 60 mm . Surface: Chrome-plated . Material: Steel, specially hardened

Tip size XZN M5 XZN M6 XZN M8 XZN M10 XZN M12 XZN M14 XZN M16 Outer Ø (mm) 22.7 22.7 22.7 22.7 23.7 23.7 27.5 Ident. No. 050 060 080 100 120 140 160 58728... ● ● ● ● ● ● ● Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH 1284Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1284_EN_2018_KERN[21850799]-c.indd 1284 12/17/2018 3:35:54 PM Screwdrivers \ Socket wrenches, 1/2 inch

Screwdriver bit For internal TORX® screws, 1/2 inch square drive 12.5 DIN 3120

Execution: Technical data: . Chrome-alloy steel . Drive: 1/2 inch . Knurled . Surface: Chrome-plated . Material: Steel, specially hardened

Tip size TX20 TX25 TX27 TX30 TX40 TX45 TX50 TX55 TX60 TX70 Outer Ø (mm) 22.7 22.7 22.7 22.7 22.7 22.7 22.7 23.7 23.7 27.5 Length (mm) 55 Ident. No. 020 025 027 030 040 045 050 055 060 070 58760... ● ● ● ● ● ● ● ● ● ● Prod. Gr. 531

Screwdriver set For internal TORX® screws, 1/2” square drive, 12.5, DIN 3120

Execution: Delivery: . Chrome-alloy steel In box with plastic inlay . Polished . Knurled

Drive 1/2 inch Sockets with socket hexagon head or external TX tip provided TX20 | TX25 | TX27 | TX30 | TX40 | TX45 | TX50 | TX55 | TX55 | TX60 Surface Chrome-plated Material Steel, specially hardened Ident. No. 200 58760... ● Prod. Gr. 531 Screwdriver bit For internal TORX® screws, 1/2 inch square drive 12.5 DIN 3120

Execution: . Drive: 1/2 inch . No. 58755: Long version . Surface: Chrome-plated . Material: Chrome-vanadium steel Technical data:

No. 58754

No. 58755

Tip size TX20 TX25 TX27 TX30 TX40 TX45 TX50 TX55 TX60 Outer Ø (mm) 22.7 22.7 22.7 22.7 22.7 22.7 22.7 23.7 23.7 Length (mm) Short 55 Ident. No. 020 025 027 030 040 045 050 055 060 58754... version ● ● ● ● ● ● ● ● ● Long 110 Ident. No. 020 025 027 030 040 045 050 055 060 58755... version ● ● ● ● ● ● ● ● ● Prod. Gr. 582

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1285 Availability subject to country specific rules and regulations.

1284_EN_2018_KERN[21850799]-c.indd 1285 12/17/2018 3:35:56 PM Screwdrivers \ Socket wrenches, 1/2 inch

Clamp strip 1/2” square drive 12.5, DIN 3120

Application: Advantage: Clamping rail with retaining clips to hold socket . Two holes for easy assembly on ﬁ xtures such as wrench inserts. a wall . Socket wrench inserts are clearly arranged so that Execution: they can be found quickly . 16 retaining clips adapted to the drive size . 2 bore holes Suitable for socket wrench drive 1/2 inch Number of attachments 16 pieces Length (mm) 430 Material Metal Ident. No. 010 58764... ● Prod. Gr. 569 Adapters ( DIN 3123 ) 1/2” square drive 12.5, DIN 3120

Application: Technical data: No. 58782 010, 58784 010, 58788 010, 58792 010: For adapting a 1/2” inter- . Drive: 1/2 inch nal square drive to a 3/8” outside square drive. . Surface: Chrome-plated No. 58782 020, 58784 020, 58788 020, 58792 020: For adapting a 1/2” internal square drive to a 3/4” outside square drive. No. 58784 005: For connecting two 1/2” internal squares.

No. 58782 010 No. 58784 005 No. 58784 010

Tip size Material 58782... 58784... 58788... 58792... Ident. No. Ident. No. Ident. No. Ident. No. 3/8 inch Chrome-vanadium steel 010 ● 010 ● 010 ● - - 3/4 inch Chrome-vanadium steel 020 ● 020 ● 020 ● - - 1/2 inch Chrome-vanadium steel - - 005 ● - - - - 3/8 inch Steel, specially hardened ------010 ● 3/4 inch Steel, specially hardened ------020 ● GEDORE = Prod. Gr. 530 STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569 a = Prod. Gr. 582 Extensions ( DIN 3123 ) 1/2” square drive 12.5, DIN 3120

Application: Extension for hand-operated socket wrench inserts with 1/2” square drive. Drive 1/2 inch 1/2 inch 1/2 inch Tip size 1/2 inch 1/2 inch 1/2 inch Length (mm) 75 125 250 Outer Ø (mm) 23 23 23 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-vanadium Chrome-vanadium Chrome-vanadium Material steel steel steel Ident. No. 010 020 030 58842... ● ● ● Prod. Gr. 582 Extensions ( DIN 3123 ) 1/2” square drive 12.5, DIN 3120

Application: Execution: Extension for hand-operated socket wrench inserts . With ball lock with 1/2” square drive. Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch Tip size 1/2 inch 1/2 inch 1/2 inch 1/2 inch Length (mm) 63 76 125 250 Outer Ø (mm) 23 23 23 23 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-vana- Chrome-vana- Chrome-vana- Chrome-vana- Material dium steel dium steel dium steel dium steel Ident. No. 006 007 010 020 58848... ● ● ● ● Prod. Gr. 530

Source: Hahn+Kolb Werkzeuge GmbH 1286Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1286_EN_2018_KERN[21850802]-k.indd 1286 12/17/2018 3:35:55 PM Screwdrivers \ Socket wrenches, 1/2 inch

Extensions ( DIN 3123 ) 1/2” square drive 12.5, DIN 3120

Application: Extension for hand-operated socket wrench inserts with 1/2” square drive. Ident. No. 020

Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch Tip size 1/2 inch 1/2 inch 1/2 inch 1/2 inch Length (mm) 76 123 248 575 Outer Ø (mm) 22.5 22.5 22.5 22.5 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-vana- Chrome-vana- Chrome-vana- Chrome-vana- Material dium steel dium steel dium steel dium steel Ident. No. 010 020 030 040 58852... ● ● ● ● Prod. Gr. 569

MORE THAN 60,000 PRODUCTS FOR MAXIMUM INNOVATION.

WE HAVE WHAT IT TAKES.

For a complete range of products that meet the toughest demands, visit www.iconridge.com

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1287 Availability subject to country specific rules and regulations.

1286_EN_2018_KERN[21850802]-k.indd 1287 12/17/2018 3:35:56 PM Screwdrivers \ Socket wrenches, 1/2 inch

Extensions ( DIN 3123 ) 1/2” square drive 12.5, DIN 3120

Application: Execution: Extension for hand-operated socket wrench inserts . Chrome-alloy steel with 1/2” square drive. Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch Tip size 1/2 inch 1/2 inch 1/2 inch 1/2 inch Length (mm) 52 75 130 255 Outer Ø (mm) 23 23.2 23.2 23.2 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Steel, specially Steel, specially Steel, specially Steel, specially Material hardened hardened hardened hardened Ident. No. 010 015 020 030 58856... ● ● ● ● Prod. Gr. 531

Extensions with conical square drive 1/2 inch square drive 12.5 DIN 3120

Application: Advantage: Extension for hand-operated socket wrench inserts . Conical outside square enables a swivelling angle with 1/2” square drive. of up to 15° Execution: . Chrome-alloy steel . Conical outside square

Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch Tip size 1/2 inch 1/2 inch 1/2 inch 1/2 inch Length (mm) 52 75 130 255 Outer Ø (mm) 23 23.2 23.2 23.2 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Steel, specially Steel, specially Steel, specially Steel, specially Material hardened hardened hardened hardened Ident. No. 010 020 030 040 58857... ● ● ● ● Prod. Gr. 531

VDE extensions 1/2” square drive

Execution: . insulation in line with DIN EN 60900 . individually tested Ident. No. 110 Drive 1/2 inch 1/2 inch 1/2 inch Tip size 1/2 inch 1/2 inch 1/2 inch Length (mm) 91 146 270 Surface VDE immer- VDE immer- VDE immer- sion-insulated sion-insulated sion-insulated Ident. No. 100 110 120 58857... ● ● ● Prod. Gr. 531

Cardan joints ( DIN 3123 ) 1/2 inch square drive 12.5 DIN 3120

Application: Cardan joint for screw connections with projecting edges and conﬁ ned installation areas.

No. 58858

Length (mm) 75 73.5 70 71 Drive Tip Surface Material 58858... 58864... 58868... 58872... size Ident. No. Ident. No. Ident. No. Ident. No. 1/2 1/2 Chrome- Chrome-vana- ● ● ● ● inch inch plated dium steel 010 010 010 010 GEDORE = Prod. Gr. 530 STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569 a = Prod. Gr. 582

Source: Hahn+Kolb Werkzeuge GmbH 1288Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1286_EN_2018_KERN[21850802]-k.indd 1288 12/17/2018 3:35:57 PM Screwdrivers \ Socket wrenches, 1/2 inch

Slip-on ratchet 1/2” square drive 12.5, DIN 3120

Application: . Can be reversed for anti-clockwise and clockwise As ratchet or torque wrench attachment for hand-op- rotation erated socket wrench inserts and connection parts with 1/2” square drive. Advantage: . For ﬂ exible use with T-handles, jointed handles etc. Execution: . Used in combination with torque wrenches for . Chrome-alloy steel controlled tightening of bolts

Tip size 1/2 inch Length (mm) 53 Number of teeth (PCS) 20 Returning angle (Degree) 18 Surface Chrome-plated Material Steel, specially hardened Ident. No. 010 58880... ● Prod. Gr. 531 Socket spanner set Hexagon, 3/4 inch square drive 20 DIN 3120

Execution: . Reversible ratchet with maximum torque of 2000 . Chrome-vanadium steel Nm . Chrome-plated Delivery: . Hexagon inserts with knurling In lacquered metal case Drive 3/4 inch 22 mm | 24 mm | 27 mm | 30 mm | 32 mm | Sockets with hexagon-head tip provided 36 mm | 38 mm | 41 mm | 46 mm | 50 mm | 55 mm | 60 mm Ratchets provided 3/4-inch square Extensions provided 200 mm | 400 mm Cross handles provided 500 mm Ident. No. 100 58902... ● Prod. Gr. 582 Socket spanner sets with hexagon inserts, 3/4 inch square drive 20 DIN 3120

Execution: Delivery: . Chrome-vanadium steel 31CrV3 In lacquered metal case . Chrome-plated . 12 inserts, 4 operating tools . Jointed handle

Drive 3/4 inch 22 mm | 24 mm | 27 mm | 30 mm | 32 mm | Sockets with hexagon-head tip provided 36 mm | 38 mm | 41 mm | 46 mm | 50 mm | 55 mm | 60 mm Ratchets provided 3/4-inch square Extensions provided 200 mm | 400 mm Cross handles provided 500 mm Hinged handles provided 547 mm Cardan joints provided 110 mm Ident. No. 120 58903... ● Prod. Gr. 530 Socket wrench sets With hexagon or bi-hexagon inserts, 3/4 inch square drive 20 DIN 3120

Execution: . Ident. No. 100: 10 inserts, 6 operating tools . Chrome-alloy steel . Ident. No. 120: 9 inserts, 6 operating tools . Chrome-plated Delivery: . Polished In lacquered metal case . Jointed handle Drive 3/4 inch 3/4 inch 22 mm | 24 mm | 27 mm | 32 mm | 34 mm | 36 mm | Ident. No. 100 30 mm | 32 mm | 34 mm | Sockets with hexagon-head tip provided 38 mm | 41 mm | 46 mm | 36 mm | 41 mm | 46 mm | 50 mm 50 mm | 55 mm | 60 mm Ratchets provided 3/4-inch square 3/4-inch square Extensions provided 200 mm | 400 mm 200 mm | 400 mm Cross handles provided 500 mm 500 mm Hinged handles provided 550 mm 550 mm Cardan joints provided 109 mm 109 mm Ident. No. 100 120 58909... ● ● Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1289 Availability subject to country specific rules and regulations.

1289_EN_2018_KERN[21850806]-m.indd 1289 12/17/2018 3:35:55 PM Screwdrivers \ 3/4-inch socket wrench

Ratchets 3/4” square drive 20, DIN 3120

Execution: . Anti-clockwise/clockwise rotation using reversing lever . With pin detent . Stop catch in the central position . Ident. No. 010: With push-through square drive and internal teeth Technical data: . Ident. No. 020: With metal reversing disc and internal teeth . Tip size: 3/4 inch . Ident. No. 030: . Surface: Chrome-plated . Plug-on bar . Material: Chrome-vanadium steel

Ident. No. 020 Ident. No. 010 Ident. No. 030

Length (mm) 510 510 620 Number of teeth (PCS) 36 50 32 Returning angle (Degree) 10 7.2 11.25 Ident. No. 010 020 030 58960... ● ● ● Prod. Gr. 530 Ratchet head 3/4” square drive 20, DIN 3120

Execution: . With QuickRelease safety lock . Chrome-alloy steel . No handle . Anti-clockwise/clockwise rotation using reversing lever Tip size 3/4 inch Length (mm) 165 Number of teeth (PCS) 36 Returning angle (Degree) 10 Surface Chrome-plated Steel, specially Material hardened Ident. No. 020 58963... ● Prod. Gr. 531 Slip-on ratchet 3/4” square drive 20, DIN 3120

Application: . used in combination with torque wrenches for as ratchet or torque wrench attachment for hand-op- controlled tightening of bolts erated socket wrench inserts and connection parts with 3/4” square drive. Technical data: . Tip size: 3/4 inch Execution: . Length: 105.5 mm . chrome-alloy steel . Number of teeth: 44 PCS . can be reversed for anti-clockwise and clockwise . Returning angle: 18 Degree rotation . Surface: Chrome-plated . Material: Steel, specially hardened Advantage: . for ﬂ exible use with T-handles, jointed handles etc.

010 58928... Ident. No. ● Prod. Gr. 531 T-handle ( DIN 3122 ) 3/4” square drive 20, DIN 3120

Application: Execution: T-handle for hand-operated socket wrench inserts . Movable sliding head and connection parts with 3/4” square drive . With pin detent Tip size 3/4 inch Length (mm) 500 Surface Chrome-plated Chrome-vana- Material dium steel Ident. No. 010 58936... ● Prod. Gr. 530

Source: Hahn+Kolb Werkzeuge GmbH 1290Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1289_EN_2018_KERN[21850806]-m.indd 1290 12/17/2018 3:35:57 PM Screwdrivers \ 3/4-inch socket wrench

Socket wrench bit ( DIN 3124 ) 3/4” square drive 20, DIN 3120

Execution: Technical data: . Ground . Drive: 3/4 inch . Surface: Chrome-plated . Material: Chrome-vanadium steel

Width across ﬂ ats 19 mm 21 mm 22 mm 24 mm 27 mm 30 mm 32 mm 34 mm Length (mm) 52 52 52 52 55 58 58 58 Outer Ø (mm) 36 36 36 38 39.5 42.3 45.8 48.3 Ident. No. 190 210 220 240 270 300 320 340 58915... ● ○ ● ● ● ● ● ● Width across ﬂ ats 36 mm 38 mm 41 mm 46 mm 50 mm 55 mm 60 mm Length (mm) 60 60 63 65 69 69 69 Outer Ø (mm) 50.8 53.5 57.1 63.3 68.3 74.6 80.8 Ident. No. 360 380 410 460 500 550 600 58915... ● ● ● ● ● ● ● Prod. Gr. 530

Socket wrench bit ( DIN 3124 ) 3/4” square drive 20, DIN 3120

Execution: Technical data: . Made from HPQ heavy-duty steel . Drive: 3/4 inch . Tip proﬁ le type: AS drive proﬁ le . Surface: Chrome-plated . Material: Steel, specially hardened

Width across ﬂ ats 19 mm 21 mm 22 mm 24 mm 27 mm 30 mm 32 mm 34 mm Length (mm) 50 50 51 51 54 58 58 60 Outer Ø (mm) 34.7 34.7 34.7 34.7 38.5 42 44.5 47 Ident. No. 190 210 220 240 270 300 320 340 58918... ● ● ● ● ● ● ● ● Width across ﬂ ats 36 mm 38 mm 41 mm 46 mm 50 mm 55 mm 60 mm Length (mm) 60 64 67 73 80 80 80 Outer Ø (mm) 49.5 52 55.5 61 66 72 78 Ident. No. 360 380 410 460 500 550 600 58918... ● ● ● ● ● ● ● Prod. Gr. 531

Socket wrench insert, long ( DIN 3124 ) 3/4” square drive 20, DIN 3120

Execution: Technical data: . Made from HPQ heavy-duty steel . Drive: 3/4 inch . Long version . Tip proﬁ le type: AS drive proﬁ le . Length: 90 mm . Surface: Chrome-plated . Material: Steel, specially hardened

Width across ﬂ ats 22 mm 24 mm 27 mm 30 mm 32 mm 34 mm 36 mm 41 mm Outer Ø (mm) 34.7 35 38.5 42 44.5 47 49.5 55.5 Ident. No. 220 240 270 300 320 340 360 410 58921... ● ● ● ● ● ● ● ●

Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1291 Availability subject to country specific rules and regulations.

1291_EN_2018_KERN[21850809]-m.indd 1291 12/17/2018 3:35:53 PM Screwdrivers \ 3/4-inch socket wrench

Screwdriver insert For hexagon socket screws, 3/4” square drive, 20, DIN 3120

Application: Technical data: Screwdriver bit for hexagon socket screws with 3/4” . Drive: 3/4 inch square drive . Length: 80 mm . Surface: Chrome-plated Execution: . Material: Steel, specially hardened . Chrome-alloy steel

Width across ﬂ ats 14 mm 17 mm 19 mm 22 mm Outer Ø (mm) 34.7 34.7 34.7 40 Ident. No. 140 170 190 220 58927... ● ● ● ● Prod. Gr. 531

Adapters ( DIN 3123 ) 3/4” square drive 20, DIN 3120

Application: No. 58930 020: For adapting a 3/4” internal square Technical data: No. 58930 005: For connecting two 3/4” internal drive to a 1” outside square drive . Drive: 3/4 inch squares No. 58933 020: For adapting a 3/4” internal square . Surface: Chrome-plated No. 58930 010, 58933 010: For adapting a 3/4” drive to a 1” external square drive internal square drive to a 1/2” outside square drive

No. 58930 005 No. 58930 020 No. 58933 020

Tip size 3/4 inch 1/2 inch 1 inch Material 005 010 020 58930... Chrome-vanadium steel Ident. No. ● ● ● Steel, specially hardened Ident. No. - 010 020 58933... ● ● GEDORE = Prod. Gr. 530 STAHLWILLE = Prod. Gr. 531

Extensions ( DIN 3123 ) 3/4” square drive 20, DIN 3120

Application: Execution: Extension for hand-operated socket wrench inserts . No. 58948: With pin detent with 3/4” square drive . No. 58951: Chrome-alloy steel No. 58948 No. 58951 Drive 3/4 inch 3/4 inch Tip size 3/4 inch 3/4 inch Length (mm) 200 400 Surface Chrome-plated Chrome-plated Outer Ø (mm) Material Chrome-vana- 010 020 58948... 33 dium steel Ident. No. ● ● 35 Steel, specially Ident. No. 010 020 58951... hardened ● ● GEDORE = Prod. Gr. 530 STAHLWILLE = Prod. Gr. 531

Cardan joint ( DIN 3123 ) 3/4” square drive 20, DIN 3120

Application: Advantage: Cardan joint for screw connections with projecting . Flexible bending angle for diﬃ cult-to-reach instal- edges and conﬁ ned installation areas lation areas Execution: . Chrome-alloy steel Drive 3/4 inch Tip size 3/4 inch Length (mm) 109 Outer Ø (mm) 40 Surface Chrome-plated Material Steel, specially hardened Ident. No. 010 58957... ● Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH 1292Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1291_EN_2018_KERN[21850809]-m.indd 1292 12/17/2018 3:35:55 PM Screwdrivers \ 1-inch socket wrench

Ratchet 1 inch square drive 25 DIN 3120

Application: . Stop catch in the central position Ratchet for hand-operated socket wrench inserts . With pin detent and connection parts with 1” square drive Advantage: Execution: . Deeper-set reversing lever prevents accidental . With plug-in handle rod reversing . Anti-clockwise/clockwise rotation using deeper-set reversing lever Tip size 1 inch Length (mm) 810 Number of teeth (PCS) 32 Returning angle (Degree) 11.25 Surface Chrome-plated Material Chrome-vanadium steel Ident. No. 010 58990... ● Prod. Gr. 530 Ratchet head 1 inch square drive 25 DIN 3120

Application: . Anti-clockwise/clockwise rotation using reversing Ratchet head for hand-operated socket wrench lever inserts and connection parts with 1” square drive . With QuickRelease safety lock . Without handle - this must be ordered separately Execution: under art. no. 58993100. . Chrome-alloy steel Tip size 1 inch Length (mm) 185 Number of teeth (PCS) 36 Returning angle (Degree) 10 Surface Chrome-plated Material Steel, specially hardened Ident. No. 010 58993... ● Prod. Gr. 531 Socket wrench bit ( DIN 3124 ) 1 inch square drive 25 DIN 3120

Execution: Technical data: . With pin detent . Drive: 1 inch . Cross-knurling . Tip proﬁ le type: UD proﬁ le . Surface: Chrome-plated . Material: Chrome-vanadium steel

Width across ﬂ ats 36 mm 41 mm 46 mm 50 mm 55 mm 60 mm 65 mm 70 mm 75 mm 80 mm Length (mm) 70 70 75 75 80 85 88 92 95 97 Outer Ø (mm) 53.9 60.1 66.4 71.4 77.6 83.9 90.1 96.4 102.6 108.9 Ident. No. 036 041 046 050 055 060 065 070 075 080 58972... ● ● ● ● ● ● ● ● ● ● Prod. Gr. 530

Socket wrench bit ( DIN 3124 ) 1 inch square drive 25 DIN 3120

Execution: Technical data: . HPQ heavy-duty steel . Drive: 1 inch . Cross-knurling . Tip proﬁ le type: AS drive proﬁ le . Surface: Chrome-plated . Material: Steel, specially hardened

Width across ﬂ ats 30 mm 32 mm 36 mm 41 mm 46 mm 50 mm 55 mm Length (mm) 65 67 67 70 75 80 85 Outer Ø (mm) 43 45 49.5 55.5 61 66 72 Ident. No. 030 032 036 041 046 050 055 58975... ● ● ● ● ● ● ● Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1293 Availability subject to country specific rules and regulations.

1293_EN_2018_KERN[21850812]-q.indd 1293 12/17/2018 3:35:55 PM Screwdrivers \ 1-inch socket wrench

Adapter ( DIN 3123 ) 1 inch square drive 25 DIN 3120

Application: Execution: For adapting a 1” internal square drive to a 3/4” . Made from HPQ heavy-duty steel external square drive. . Maximum load: 1412 Nm Drive 1 inch Tip size 3/4 inch Surface Chrome-plated Material Steel, specially hardened Ident. No. 010 58978... ● Prod. Gr. 531

Screwdriver bit For hexagon socket screws, 1” square drive, 25, DIN 3120

Execution: . Chrome-alloy steel . Technical data: Knurled . Drive: 1 inch Advantage: . Surface: Chrome-plated . Material: Steel, specially hardened . Good grip thanks to knurling

Width across ﬂ ats 14 mm 17 mm 19 mm 22 mm 24 mm 27 mm Length (mm) 85 85 85 90 90 90 Outer Ø (mm) 43 43 43 48 48 49 Ident. No. 140 170 190 220 240 270 58981... ● ● ● ● ● ● Prod. Gr. 531

Extensions ( DIN 3123 ) 1 inch square drive 25 DIN 3120

Application: Execution: Extension for hand-operated socket wrench inserts . No. 58984: With pin detent with 1” square drive . No. 58987: Chrome-alloy steel No. 58984 No. 58987 Drive 1 inch 1 inch 1 inch 1 inch Length (mm) 200 400 200 410 Outer Ø (mm) 48 48 43 43 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-vana- Chrome-vana- Steel, specially Steel, specially Material dium steel dium steel hardened hardened Ident. No. 010 020 58984... ● ● - - 010 020 58987... Ident. No. - - ● ● GEDORE = Prod. Gr. 530 STAHLWILLE = Prod. Gr. 531

Socket wrench bits with 1/4” hexagon drive

Execution: Advantage: . External hexagon drive according to DIN 3126, . No. 52401: Magnet holds the bolt or nut securely type E 6.3 in place until screwdriving is complete . Hexagon socket drive according to DIN 475/2

Drive 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch Width across ﬂ ats 5.5 mm 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm Length (mm) 50 50 50 50 50 50 50 50 50 Outer Ø (mm) 10 12 12 14 14 16 16 16 19 Excluding 52400... permanent Ident. No. 055 060 070 080 090 100 110 120 130 magnet ● ● ● ● ● ● ● ● ● With 52401... permanent Ident. No. 055 060 070 080 090 100 110 120 130 magnet ● ● ● ● ● ● ● ● ● Prod. Gr. 540

Source: Hahn+Kolb Werkzeuge GmbH 1294Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1293_EN_2018_KERN[21850812]-q.indd 1294 12/17/2018 3:35:56 PM Screwdrivers \ Socket wrenches, machine operated

Socket wrench bits with 1/4” square drive

Execution: Advantage: . Square drive according to DIN 3121 type G . No. 52411: Magnet holds the bolt or nut securely . Hexagon socket drive according to DIN 475/2 in place until screwdriving is complete

Drive 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch Width across ﬂ ats 4 mm 5 mm 5.5 mm 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm Length (mm) 23 23 23 23 23 23 23 23 23 23 23 25 Outer Ø (mm) 7.7 8.9 9.5 10.2 11.4 12.7 13.5 15.3 16.5 17.9 19.7 20.5 Excluding 52410... permanent Ident. No. 040 050 055 060 070 080 090 100 110 120 130 140 magnet ● ● ● ● ● ● ● ● ● ● ● ○ With 52411... permanent Ident. No. - - - 060 070 080 - 100 - - 130 - magnet ○ ● ● ● ● Prod. Gr. 540

Socket wrench insert, long 1/4” square drive and spring element

Execution: The spring-mounted magnet is pressed further into . Square drive according to DIN 3121 type G the tool by the bolt without pushing the nut out of . Hexagon socket drive according to DIN 3129 the tool. . With spring-loaded permanent magnets . Screw/nut is in a secure position and is easy to remove Advantage: . When tightening a screw nut, there is suﬃ cient space for the threaded bolt to extend into the tool.

Drive 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch Width across ﬂ ats 7 mm 8 mm 9 mm 10 mm 12 mm 13 mm 14 mm Length (mm) 45 45 50 45 50 45 50 Outer Ø (mm) 11.4 12.7 12.1 15.3 18 19 20 Ident. No. 070 080 090 100 120 130 140 52413... ● ● ○ ● ● ● ● Prod. Gr. 540

Socket wrench bits with 3/8 inch square drive

Execution: Advantage: . Square drive according to DIN 3121 type G . No. 52421: Magnet holds the bolt or nut securely . Hexagon socket drive according to DIN 475/2 in place until screwdriving is complete

Drive 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch Width across ﬂ ats 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm Length (mm) 30 30 30 30 30 30 30 Outer Ø (mm) 12.5 13.8 15 16.4 17.7 19 20.2 Excluding 52420... permanent Ident. No. 070 080 090 100 110 120 130 magnet ● ● ● ● ● ● ● With perma- 080 090 100 - - 130 52421... nent magnet Ident. No. - ● ○ ● ● Drive 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch Width across ﬂ ats 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm 11 mm Length (mm) 30 30 30 30 30 30 30 Outer Ø (mm) 21.5 22.9 24.3 25.4 26.6 27.9 19 Excluding 52420... permanent Ident. No. 140 150 160 170 180 190 - magnet ● ● ● ● ○ ● With perma- 140 150 160 170 - - 110 52421... nent magnet Ident. No. ○ ○ ● ● ○ Prod. Gr. 540

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1295 Availability subject to country specific rules and regulations.

1293_EN_2018_KERN[21850812]-q.indd 1295 12/17/2018 3:35:58 PM Screwdrivers \ Socket wrenches, machine operated

MORE THAN 60,000 PRODUCTS FOR MAXIMUM INNOVATION. WE HAVE WHAT IT TAKES.

For a complete range of products that meet the toughest demands, visit www.iconridge.com

Source: Hahn+Kolb Werkzeuge GmbH 1296Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1293_EN_2018_KERN[21850812]-q.indd 1296 12/17/2018 3:35:58 PM Screwdrivers \ Socket wrenches, machine operated

Socket wrench insert 3/8 inch square drive and magnetic element

Execution: The spring-mounted magnet is pressed further into . Square drive according to DIN 3121 type G the tool by the bolt without pushing the nut out of . Hexagon socket drive according to DIN 475/2 the tool. . With spring-loaded permanent magnets . Screw/nut is in a secure position and is easy to remove Advantage: . When tightening a screw nut, there is suﬃ cient space for the threaded bolt to extend into the tool.

Drive 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch Width across ﬂ ats 8 mm 10 mm 12 mm 13 mm 14 mm 16 mm 17 mm Length (mm) 50 50 55 50 55 55 55 Outer Ø (mm) 13.5 16.4 19 20.2 21 21.6 25.2 Ident. No. 080 100 120 130 140 160 170 52423... ● ● ○ ● ● ● ● Prod. Gr. 540

Socket wrench bit 3/8”-square drive

Execution: . Square drive according to DIN 3121 type G . TX output

Drive 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch Tip size E5 E6 E7 E8 E10 E12 E14 Length (mm) 32 32 32 32 32 32 32 Outer Ø (mm) 7 8 10 11 13 15 17 Ident. No. 005 006 007 008 010 012 014 52425... ○ ● ○ ● ● ● ● Prod. Gr. 540

Socket wrench bit 3/8”-square drive

Execution: Technical data: . Square drive according to DIN 3121 type G . Drive: 3/8 inch . TX output for internal TX screws . Length: 50 mm . Outer diameter: 22 mm

Tip size TX20 TX25 TX27 TX30 TX40 Ident. No. 020 025 027 030 040 52427... ○ ● ○ ● ● Prod. Gr. 540

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1297 Availability subject to country specific rules and regulations.

1293_EN_2018_KERN[21850812]-q.indd 1297 12/17/2018 3:35:59 PM Screwdrivers \ Socket wrenches, machine operated

Socket wrench bit 3/8”-square drive

Execution: . Square drive according to DIN 3121 type G . External hexagon drive according to DIN ISO 2963

Drive 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch 3/8 inch Width across ﬂ ats 5 mm 6 mm 8 mm 10 mm 12 mm 14 mm Length (mm) 50 50 50 50 50 50 Outer Ø (mm) 22 22 22 22 22 22 Ident. No. 050 060 080 100 120 140 52428... ● ● ● ● ● ● Prod. Gr. 540

Hexagon socket wrench sets with 1/2” square drive Hexagon head, hexagon socket and TORX

Application: Advantage: Ident. No. 100: Wheel nut inserts for gentle rim assembly . Ident. No. 100: Gentle bolting thanks to plastic coating for optimum rim protection Execution: . Ident. No. 100: Plastic-coated Delivery: . Ident. No. 120: 10 inserts, 2 operating tools Ident. No. 120–165: In stable plastic box with so foam inlay

Ident. No. 100 Ident. No. 120 Ident. No. 155 Ident. No. 165

Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch 9 mm | 10 mm | 11 mm | Sockets with hexagon-head tip provided - 13 mm | 14 mm | 17 mm - - | 19 mm | 22 mm | 24 mm | 27 mm Long sockets with hexagon-head tip provided 17 mm | 19 mm | 21 mm - - - Sockets with socket hexagon-head tip 4 mm | 5 mm | 6 mm | 8 provided - - mm | 10 mm | 12 mm | 14 - mm | 17 mm | 19 mm TX40 | TX45 | TX47 | TX50 Sockets with socket hexagon head or external - - - | TX55 | TX60 | TX70 | E10 TX tip provided | E11 | E12 | E14 | E16 | E18 | E20 | E22 | E24 Extensions provided - 175 mm - - Cardan joints provided - 75 mm - - Number of pieces in assortment/set (PCS) 3 12 9 16 Ident. No. 100 120 155 165 52458... ● ● ● ● Prod. Gr. 540

Socket wrench bit 1/2”-square drive

Execution: . Square drive according to DIN 3121 type G . Internal hexagon drive according to DIN 475/2

Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch Width across ﬂ ats 10 mm 11 mm 12 mm 13 mm 14 mm 15 mm 16 mm 17 mm Length (mm) 38 38 38 38 38 38 38 38 Outer Ø (mm) 17.6 18.9 20.2 21.4 22.7 23.9 25.3 26.6 Ident. No. 100 110 120 130 140 150 160 170 52430... ● ● ● ● ● ● ● ● Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch Width across ﬂ ats 18 mm 19 mm 20 mm 21 mm 22 mm 24 mm 27 mm 30 mm Length (mm) 38 38 38 38 38 45 50 50 Outer Ø (mm) 27.9 29.1 30.5 32 32.9 35.4 39.3 43 Ident. No. 180 190 200 210 220 240 270 300 52430... ● ● ● ● ● ● ● ● Prod. Gr. 540 Source: Hahn+Kolb Werkzeuge GmbH 1298Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1298_EN_2018_KERN[21850819]-r.indd 1298 12/17/2018 3:36:03 PM Screwdrivers \ Socket wrenches, machine operated

Socket wrench bit 1/2”-square drive

Execution: . Square drive according to DIN 3121 type G . Internal hexagon drive according to DIN 475/2 . Long version

Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch Width across ﬂ ats 10 mm 13 mm 14 mm 16 mm 17 mm 18 mm 19 mm 21 mm 22 mm 24 mm 27 mm Length (mm) 78 78 78 78 78 78 78 78 78 78 78 Outer Ø (mm) 17.6 21.4 22.7 25.4 26.6 27.7 29.1 31.4 32.8 35.3 39 Ident. No. 100 130 140 160 170 180 190 210 220 240 270 52431... ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 540

Socket wrench bit 1/2”-square drive

Execution: . Square drive according to DIN 3121 type G . output for external TX screws with E proﬁ le

Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch Tip size E10 E12 E14 E16 E18 E20 E24 Length (mm) 38 38 38 38 38 38 38 Outer Ø (mm) 14 16 17 20 21 24 30 Ident. No. 010 012 014 016 018 020 024 52435... ● ● ● ● ● ● ● Prod. Gr. 540

Socket wrench bit 1/2”-square drive

Execution: . Square drive according to DIN 3121 type G . TX output for internal TX screws

Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch Tip size TX30 TX40 TX50 TX55 TX60 Length (mm) 55 55 55 55 55 Outer Ø (mm) 30 30 30 30 30 Ident. No. 030 040 050 055 060 52436... ● ● ● ● ● Prod. Gr. 540

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1299 Availability subject to country specific rules and regulations.

1298_EN_2018_KERN[21850819]-r.indd 1299 12/17/2018 3:36:04 PM Screwdrivers \ Socket wrenches, machine operated

Socket wrench bit For hexagon socket screws according to DIN 7462, with 1/2” square drive

Execution: . Square drive according to DIN 3121 type G . External hexagon drive according to DIN ISO 2963

Drive 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch Width across ﬂ ats 5 mm 6 mm 8 mm 10 mm 12 mm 14 mm 17 mm Length (mm) 55 55 55 55 55 55 55 Ident. No. 050 060 080 100 120 140 170 52437... ● ● ● ● ● ● ● Prod. Gr. 540

Socket wrench bit 3/4”-square drive

Execution: . Square drive according to DIN 3121 type H . Internal hexagon drive according to DIN 475/2

Drive 3/4 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch Width across ﬂ ats 17 mm 19 mm 22 mm 24 mm 27 mm 30 mm 32 mm 36 mm 41 mm 46 mm Length (mm) 50 50 50 50 54 54 56 56 58 63 Outer Ø (mm) 30 32.5 36.5 38.9 42.5 46.5 48.8 53.8 60 66.5 Ident. No. 170 190 220 240 270 300 320 360 410 460 52440... ● ● ● ● ● ● ● ● ● ● Prod. Gr. 540

Socket wrench bit 3/4”-square drive

Execution: . Square drive according to DIN 3121 type G . External hexagon drive according to DIN ISO 2963

Drive 3/4 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch Width across ﬂ ats 14 mm 17 mm 19 mm 22 mm 24 mm 27 mm Length (mm) 62 62 62 62 62 62 Outer Ø (mm) 44 44 44 44 44 44 Ident. No. 140 170 190 220 240 270 52442... ● ● ● ● ● ●

Prod. Gr. 540

Source: Hahn+Kolb Werkzeuge GmbH 1300Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1298_EN_2018_KERN[21850819]-r.indd 1300 12/17/2018 3:36:05 PM Screwdrivers \ Socket wrenches, machine operated

Socket spanner insert 3/4”-square drive

Execution: . Square drive according to DIN 3121 type H . Internal hexagon drive according to DIN 475/2 . Long version

Drive 3/4 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch Width across ﬂ ats 17 mm 19 mm 22 mm 24 mm 27 mm 30 mm 32 mm 36 mm 41 mm 46 mm Length (mm) 95 95 95 95 95 95 95 95 95 100 Outer Ø (mm) 30 32.5 36.5 38.9 42.5 46.5 48.8 53.8 60 66.5 Ident. No. 170 190 220 240 270 300 320 360 410 460 52441... ● ● ● ● ● ● ● ● ● ● Prod. Gr. 540

Connector with male/female square drive and quick-change holder

Execution: . Square drive according to DIN 3121 . External square drive according to DIN 3120 type A with ball lock

Drive 1/4 inch 3/8 inch 1/2 inch 3/4 inch Tip size 1/4 inch 3/8 inch 1/2 inch 3/4 inch Length (mm) 35 45 55 78 Outer Ø (mm) 13 20 25 44 Ident. No. 010 110 210 310 52445... ○ ● ● ● Prod. Gr. 540 Tool shank For socket wrench inserts no. 52410-52441

Application: Execution: Tool shank for machine-operated socket wrench . 7/16” external hexagon drive according to DIN inserts 3126, type E 11.2 (ISO 1173) . 1/2” external square drive according to DIN 3121 type E 12.5 with spring-loaded pin Drive 7/16 inch Tip size 1/2 inch Length (mm) 75 Ident. No. 275 52450... ● Prod. Gr. 540 Tool shank/connector for socket wrench inserts no. 52410-52441

Application: Execution: for machine-operated socket wrench inserts. . hexagonal drive, square output . with spring-loaded pin or ball lock

Ident. No. 400–410

Ident. No. 420–450

Drive 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch Tip size 1/4 inch 3/8 inch 1/4 inch 1/4 inch 3/8 inch 1/2 inch Length (mm) 25 30 50 100 50 50 Ident. No. 400 410 420 430 440 450 52450... ● ● ● ● ● ● Prod. Gr. 540

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1301 Availability subject to country specific rules and regulations.

1298_EN_2018_KERN[21850819]-r.indd 1301 12/17/2018 3:36:07 PM Screwdrivers \ Socket wrenches, machine operated

Connector/holder for bits connector with snap ring, for mechanical drive

Application: Execution: for direct mounting of D 6.3 bits . square drive, hexagonal output Drive 1/4 inch 3/8 inch 1/2 inch 1/2 inch Tip size 1/4 inch 1/4 inch 1/4 inch 5/16 inch Length (mm) 25 30 35 35 Ident. No. 500 510 520 530 52450... ● ● ● ● Prod. Gr. 540

Connectors for bits Connectors with quick-change holders, machine-operated

Application: Connection part for mounting C 6.3 bits

Drive 1/4 inch 3/8 inch 1/2 inch Tip size 1/4 inch 1/4 inch 1/4 inch Length (mm) 35 30 35 Ident. No. 635 645 655 52450... ● ● ● Prod. Gr. 540 Adapters for machine-operated screw tools For socket wrench inserts no. 52410-52441

Application: Execution: Adaptation from internal square to external square . Ident. No. 135–245, 370: square drive with spring-loaded pin . Ident. No. 250, 470: square drive with end-to-end pin hole

Drive 3/8 inch 3/8 inch 1/2 inch 1/2 inch 3/4 inch 1 inch Tip size 1/4 inch 1/2 inch 3/8 inch 3/4 inch 1/2 inch 3/4 inch Length (mm) 32 36 38 48 58 70 Ident. No. 135 145 245 250 370 470 52451... ● ● ● ● ● ● Prod. Gr. 540

Ball joints for machine-operated screwdrivers For socket wrench inserts no. 52410-52441

Execution: . Ident. No. 045–275: With spring-loaded pin . Ident. No. 390: With end-to-end pin hole

Drive 1/4 inch 3/8 inch 1/2 inch 3/4 inch Tip size 1/4 inch 3/8 inch 1/2 inch 3/4 inch Length (mm) 45 55 75 90 Ident. No. 045 155 275 390 52452... ● ● ● ● Prod. Gr. 540

Extensions for machine-operated screwdrivers For socket wrench inserts no. 52410-52441

Execution: . Ident. No. 005–225: With spring-loaded pin . Ident. No. 317–333: With end-to-end pin hole

Drive 1/4 inch 1/4 inch 3/8 inch 3/8 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 3/4 inch 3/4 inch 3/4 inch Tip size 1/4 inch 1/4 inch 3/8 inch 3/8 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch 3/4 inch 3/4 inch 3/4 inch Length (mm) 50 150 75 150 50 75 125 250 175 250 330 Ident. No. 005 015 107 115 205 207 212 225 317 325 333 52453... ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 540

Source: Hahn+Kolb Werkzeuge GmbH 1302Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1298_EN_2018_KERN[21850819]-r.indd 1302 12/17/2018 3:36:12 PM Screwdrivers \ Socket wrenches, machine operated

Square ring wrench ( DIN 248 )

Execution: Advantage: . Special steel . Excellent material strength with low-tension . With end-to-end square microstructure . Surface annealed in burnished ﬁ nish . Better resistance to corrosion

Width across ﬂ ats 8 mm 10 mm 12 mm 13 mm 14 mm 17 mm 19 mm 22 mm 24 mm Length (mm) 160 195 235 250 270 315 345 385 415 Outer Ø (mm) 17 21 24 26 27 31 35 39 43 Ident. No. 080 100 120 130 140 170 190 220 240 52095... ● ● ● ● ● ● ● ● ● Prod. Gr. 532 Hook wrenches With nose

Execution: . Better resistance to corrosion . Special steel . Comfortable to use . Rounded edges . With suspension hole Technical data: . Suitable for nut type: Slotted nut DIN 1804 . Surface annealed in burnished ﬁ nish | Bearing nut DIN 981 Advantage: . Excellent material strength with low-tension microstructure

Suitable for min./max. nut male thread size 12-14 mm 16-20 mm 25-28 mm 30-32 mm 34-36 mm 38-45 mm 40-42 mm 45-50 mm Length (mm) 110 110 136 136 170 170 170 206 Thickness (mm) 3 3 4 4 5 5 5 6 Ident. No. 010 020 030 040 050 055 060 070 52100... ● ● ● ● ● ● ● ● Suitable for min./max. nut male thread size 52-55 mm 58-62 mm 65-70 mm 68-75 mm 80-90 mm 85-92 mm 95-100 mm 98-105 mm Length (mm) 206 240 240 240 280 280 280 290 Thickness (mm) 6 7 7 7 8 8 8 8 Ident. No. 080 090 095 100 110 115 120 125 52100... ● ● ● ● ● ● ● ● Suitable for min./max. nut male thread size 110-115 mm 120-130 mm 135-145 mm 155-165 mm 180-195 mm 208-220 mm 230-245 mm 260-270 mm Length (mm) 335 335 385 385 470 470 568 568 Thickness (mm) 10 10 10 10 10 10 10 10 Ident. No. 130 140 150 160 170 180 190 200 52100... ● ● ● ● ● ● ● ● Suitable for min./max. nut male thread size 280-300 mm Length (mm) 680 Thickness (mm) 15 Ident. No. 210 52100... ● Prod. Gr. 532 Hook wrenches With pin

Execution: Advantage: . Special steel . Excellent material strength with low-tension . Rounded edges microstructure . With suspension hole . Increased resistance to corrosion . Surface annealed in burnished ﬁ nish . More comfortable handling

Technical data: . Suitable for nut type: Round nut with set pin holes DIN 1816 Suitable for min./max. nut male thread size 12-14 mm 16-18 mm 20-22 mm 25-28 mm 30-32 mm 34-36 mm 40-42 mm 45-50 mm Tenon Ø (mm) 2 2.5 2.5 3 4 4 4 5 Length (mm) 110 110 110 136 136 170 170 206 Ident. No. 010 020 030 040 050 060 070 080 52102... ● ● ● ● ● ● ● ● Suitable for min./max. nut male thread size 52-55 mm 58-62 mm 68-75 mm 80-90 mm 95-100 mm 110-115 mm 120-130 mm 135-145 mm Tenon Ø (mm) 5 5 6 6 8 8 8 8 Length (mm) 206 240 240 280 280 335 335 380 Ident. No. 090 100 110 120 130 140 150 160 52102... ● ● ● ● ● ● ● ● Suitable for min./max. nut male thread size 155-165 mm 180-195 mm 205-220 mm 230-245 mm Tenon Ø (mm) 8 10 10 10 Length (mm) 380 470 470 568 Ident. No. 170 180 190 200 52102... ● ● ● ● Prod. Gr. 532 Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1303 Availability subject to country specific rules and regulations.

1298_EN_2018_KERN[21850819]-r.indd 1303 12/17/2018 3:36:14 PM Screwdrivers \ Hook wrenches

CHOOSE FROM OVER 70,000 PRODUCTS.

WE HAVE WHAT IT TAKES.

For a complete range of products that meet the toughest demands, visit iconridge.com

Source: Hahn+Kolb Werkzeuge GmbH 1304Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1298_EN_2018_KERN[21850819]-r.indd 1304 12/17/2018 3:36:14 PM Screwdrivers \ Hook wrenches

Articulated hook wrench, industrial version For DIN 1804 slotted nuts and DIN 981 roller bearing nuts

Execution: . Reinforced rivet for longer service life with greater . Special steel force transmission . Rounded edges . Even movement with additional spring washer . With suspension hole . One-hand operation possible . Extended hook and shank . Excellent material strength with low-tension . Reinforced rivet microstructure . With spring washer Technical data: . Surface annealed in burnished ﬁ nish . Suitable for nut type: Slotted nut DIN 1804 | Advantage: Bearing nut DIN 981 . Longer shank for greater transferable torque Suitable for min./max. nut male thread size 20-35 mm 35-60 mm 60-90 mm 90-155 mm 155-230 mm Thickness (mm) 4 5 6 7 8 Length (mm) 165 210 280 335 460 Ident. No. 010 020 030 040 050 52104... ● ● ● ● ● Prod. Gr. 532 Articulated plier wrench, industrial version for DIN 1816 capstan nuts

Suitable for min./max. nut male thread size 16-22 mm 22-35 mm 35-60 mm 60-90 mm 95-155 mm 165-230 mm Tenon Ø (mm) 2.5 3 4 6 6 10 Length (mm) 135 165 205 280 335 460 Ident. No. 016 022 035 060 095 165 52106... ● ● ● ● ● ● Prod. Gr. 532 Face wrench Adjustable

Execution: Technical data: . Special steel . Suitable for nut type: Round nuts with drilled holes . Surface annealed in burnished ﬁ nish in one face

Min./max. half-dog point spacing 7-40 mm 7-40 mm 7-40 mm 11-60 mm 11-60 mm 11-60 mm 14-100 mm 14-100 mm Tenon Ø (mm) 1.5 2 2.5 3 4 5 5 6 Width of side (mm) 3 3 3 4 4 4 6 6 Length (mm) 115 115 115 160 160 160 215 215 Ident. No. 010 020 030 040 050 060 070 080 52110... ● ● ● ● ● ● ● ● Min./max. half-dog point spacing 14-100 mm 22-125 mm 22-125 mm Tenon Ø (mm) 8 8 10 Width of side (mm) 6 6 6 Length (mm) 215 260 260 Ident. No. 090 100 110 52110... ● ● ● Prod. Gr. 532

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1305 Availability subject to country specific rules and regulations.

1298_EN_2018_KERN[21850819]-r.indd 1305 12/17/2018 3:36:15 PM Screwdrivers \ Hook wrenches

Articulated face wrench For two-hole nuts

Execution: Technical data: . Special steel . Suitable for nut type: Round nuts with drilled holes . With welded-on pin in one face . With suspension hole . Surface annealed in burnished ﬁ nish

Min./max. half-dog point spacing 18-40 mm 18-40 mm 40-80 mm 40-80 mm 40-80 mm 80-125 mm 80-125 mm 80-125 mm Tenon Ø (mm) 3 4 4 5 6 6 7 8 Width of side (mm) 5 5 6 6 6 8 8 8 Length (mm) 150 150 220 220 220 295 295 295 Ident. No. 010 020 030 040 050 060 070 080 52112... ● ● ● ● ● ● ● ● Min./max. half-dog point spacing 125-200 mm 125-200 mm Tenon Ø (mm) 8 10 Width of side (mm) 10 10 Length (mm) 405 405 Ident. No. 090 100 52112... ● ● Prod. Gr. 532

Hexagon angled screwdriver, short design (Hex keys)

Execution: Advantage: . Chrome-vanadium steel . Better resistance to corrosion

Width across fl ats 0.7 mm 0.9 mm 1.3 mm 1.5 mm 2 mm 2.5 mm 3 mm Limb length x limb length 2 33 x 7 mm 33 x 11 mm 41 x 13 mm 46.5 x 15.5 58.5 x 20.5 mm 52 x 18 mm mm 66 x 23 mm Surface Burnished Burnished Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated Version Short Ident. No. 470 480 490 500 510 520 530 52114... ● ● ● ● ● ● ● Width across fl ats 4 mm 5 mm 6 mm 7 mm 8 mm 9 mm 10 mm Limb length x limb length 2 74 x 29 mm 85 x 33 mm 96 x 38 mm 102 x 41 mm 108 x 44 mm 114 x 47 mm 122 x 50 mm Surface Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated Version Short Ident. No. 540 550 560 570 580 590 600 52114... ● ● ● ● ● ● ● Width across fl ats 11 mm 12 mm 14 mm 17 mm 19 mm 22 mm 24 mm Limb length x limb length 2 129 x 53 mm 137 x 57 mm 154 x 70 mm 177 x 80 mm 199 x 89 mm 222 x 102 mm 248 x 114 mm Surface Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated Version Short Ident. No. 610 620 630 640 650 660 665 52114... ● ● ● ● ● ● ● Width across fl ats 27 mm 30 mm 32 mm 36 mm Limb length x limb length 2 277 x 127 mm 315 x 142 mm 347 x 157 mm 391 x 176 mm Surface Nickel-plated Nickel-plated Nickel-plated Nickel-plated Version Short Ident. No. 670 675 680 685 52114... ● ● ● ● Prod. Gr. 590

Source: Hahn+Kolb Werkzeuge GmbH 1306Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1306_EN_2018_KERN[21850828]-p.indd 1306 12/17/2018 3:35:53 PM Screwdrivers \ Hexagon and TORX screwdrivers

Hexagon angled screwdriver, long design (Hex keys)

Execution: . Chrome-vanadium steel Technical data: Advantage: . Surface: Nickel-plated . Excellent material strength . Better resistance to corrosion

Width across fl ats 1.5 mm 2 mm 2.5 mm 3 mm 4 mm 5 mm 6 mm 91.5 x 15.5 114.5 x 20.5 Limb length x limb length 2 mm 102 x 18 mm mm 129 x 23 mm 144 x 29 mm 165 x 33 mm 186 x 38 mm Version Long Ident. No. 500 510 520 530 540 550 560 52116... ● ● ● ● ● ● ● Width across fl ats 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 14 mm Limb length x limb length 2 197 x 41 mm 208 x 44 mm 219 x 47 mm 234 x 50 mm 247 x 53 mm 262 x 57 mm 294 x 70 mm Version Long Ident. No. 570 580 590 600 610 620 630 52116... ● ● ● ● ● ● ● Width across fl ats 17 mm 19 mm 22 mm Limb length x limb length 2 337 x 80 mm 379 x 89 mm 422 x 102 mm Version Long Ident. No. 640 650 660 52116... ● ● ● Prod. Gr. 590

Hexagon oﬀ set screwdriver sets (Hex keys)

Execution: . Chrome-vanadium steel Technical data: Advantage: . Surface: Nickel-plated . Excellent material strength . Better resistance to corrosion

No. 52116 705–52116 715 No. 52114 705–52114 725 No. 52114 800, 52116 805

2 mm | 2.5 mm | 3 mm 2 mm | 2.5 mm | 3 mm 2 mm | 2.5 mm | 3 mm | 4 mm | 5 mm | 6 mm Width across ﬂ ats | 4 mm | 5 mm | 6 mm | 4 mm | 5 mm | 6 mm | 8 mm | 10 mm | 12 | 8 mm | 10 mm mm | 14 mm Number of pieces in assortment/set (PCS) 6 8 10 Version In plastic bag Short Ident. No. 705 715 725 52114... ● ● ● In long version bag Short Ident. No. - 800 52114... ● - In plastic bag Long Ident. No. 705 715 52116... ● ● - 805 52116... In long version bag Long Ident. No. - ● - Prod. Gr. 590

Hexagon oﬀ set screwdriver sets (Hex keys)

Execution: Technical data: . Chrome-vanadium steel . Width across ﬂ ats: 1.5 mm | 2 mm | 2.5 mm | 3 mm | 4 mm | 5 mm | 6 mm | 7 mm | 8 mm | 9 Advantage: mm | 10 mm . Compact holder . Surface: Nickel-plated Ident. No. 115 . Better resistance to corrosion . Number of pieces in assortment/set: 11

Version Ident. No. 025 In compact holder Short Ident. No. 025 52120... ● In compact holder Long Ident. No. 115 52120... ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1307 Availability subject to country specific rules and regulations.

1306_EN_2018_KERN[21850828]-p.indd 1307 12/17/2018 3:35:55 PM Screwdrivers \ Hexagon and TORX screwdrivers

Hexagon angled screwdriver with Magic-Ring® (T-handle wrench)

Execution: . Makes it easier to remove countersunk screws and . Chrome-vanadium steel to insert screws into slanted or deep blind holes . Long version with spring steel ring . Suitable for stainless steel, brass or other . In ProStar holder non-magnetic screws Advantage: Technical data: . Excellent retention force thanks to robust, wear- . Surface: Nickel-plated proof spring steel ring

Width across ﬂ ats 3 mm 4 mm 5 mm 6 mm 8 mm 10 mm Limb length x limb length 2 128 x 23 mm 142 x 29 mm 163 x 33 mm 184 x 38 mm 206 x 44 mm 231 x 50 mm Version Long Ident. No. 030 040 050 060 080 100 52122... ● ● ● ● ● ● Prod. Gr. 533

Hexagon angled screwdriver set with Magic-Ring® (T-handle wrench), long version in Pro Star tool holder

Execution: Advantage: . Chrome-vanadium steel . Excellent retention force thanks to robust, wear- . Magic-Ring® from 3 mm proof spring steel ring . Long version with spring steel ring . Makes it easier to remove countersunk screws and . In ProStar holder to insert screws into slanted or deep blind holes . Suitable for stainless steel, brass or other non-magnetic screws

1.5 mm | 2 mm | 2.5 mm | 3 Width across ﬂ ats mm | 4 mm | 5 mm | 6 mm | 8 mm | 10 mm Surface Nickel-plated Version Long Ident. No. 200 52122... ● Prod. Gr. 533

Screwdriver sets In foldaway hand case

Application: . Two-component foldaway holder with li ing device Ident. No. 100–110: For hexagon socket screws. . Ident. No. 120: Steel grey Ident. No. 120: for internal TX screws. Advantage: Execution: . Better resistance to corrosion . Screwdriver blades made from chrome-vanadium steel

Ident. No. 100 Ident. No. 110 Ident. No. 120

Tip size - - TX9 | TX10 | TX15 | TX20 | TX25 | TX27 | TX30 | TX40 Width across ﬂ ats 1.5 mm | 2 mm | 2.5 mm | 3 mm | 2.5 mm | 3 mm | 4 mm | 5 mm | 6 - 4 mm | 5 mm | 6 mm mm | 8 mm | 10 mm Surface Nickel-plated Nickel-plated - Number of pieces in assortment/set 7 7 8 Ident. No. 100 110 120 52130... ● ● ● Prod. Gr. 590

Source: Hahn+Kolb Werkzeuge GmbH 1308Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1308_EN_2018_KERN[21850831]-q.indd 1308 12/17/2018 3:35:56 PM Screwdrivers \ Hexagon and TORX screwdrivers

Screwdriver sets In PocketStar®

Application: Execution: Ident. No. 300–340: For hexagon socket screws. . Screwdriver blades made from chrome-vanadium steel Ident. No. 380: for internal TX screws. . Ident. No. 340: With ball end and spring steel ring Ident. No. 400: For a range of screw proﬁ les. Advantage: . Easy to choose the blade using li ing button . Higher torques possible thanks to glass-ﬁ bre-reinforced polyamide housing

Ident. No. 300 Ident. No. 340 Ident. No. 380 Ident. No. 400

TX9 | TX10 | TX15 | TX20 | Tip size - - PH2 | TX10 | TX15 | TX20 TX25 | TX27 | TX30 | TX40 Width across ﬂ ats 2 mm | 2.5 mm | 3 mm | 4 2 mm | 2.5 mm | 3 mm | 4 - 3 mm | 4 mm | 5 mm | mm | 5 mm | 6 mm | 8 mm mm | 5 mm | 6 mm | 8 mm 6 mm Slot width (mm) - - - 4.5 Surface Chrome-plated Nickel-plated Chrome-plated Bare Number of pieces in assortment/set 7 7 8 9 Ident. No. 300 340 380 400 52135... ● ● ● ● Prod. Gr. 533

Mini PocketStar

Application: Advantage: For the smallest screw connections such as fasten- . Easy to choose the blade using li ing button ing and adjusting sensors. Technical data: Execution: . Slot width: 2.0 mm . Screwdriver blades made from chrome-vanadium . Surface: Nickel-plated steel . Housing made from ﬁ breglass-reinforced polyamide

Width across ﬂ ats 0.7 mm | 0.9 mm | 1.3 mm | 2 mm 1.5 mm | 2 mm Tip size PH00 PH00 | TX4 | TX5 | TX6 | TX7 Ident. No. 500 550 52135... ● ● Prod. Gr. 533

Hexagonal angled screwdriver Angled blade

Execution: Advantage: . Blade made of chrome-vanadium steel . Higher torques thanks to extended lever action . Hardened . So Finish® handle with roll-oﬀ protection Technical data: . V e r s i o n : O ﬀ s e t . Surface: Chrome-plated

Width across ﬂ ats 3 mm 4 mm 5 mm 6 mm 8 mm 10 mm Blade length (mm) 35 40 45 50 60 70 Length (mm) 139 151 156 168 178 199 Ident. No. 430 440 450 460 480 500 52136... ● ● ● ● ● ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1309 Availability subject to country specific rules and regulations.

1308_EN_2018_KERN[21850831]-q.indd 1309 12/17/2018 3:35:57 PM Screwdrivers \ Hexagon and TORX screwdrivers

Hexagonal screwdriver with T-handle with 2-component handle

Execution: . Optimum performance data up to 100% above the . Easy-grip so coating for optimum power DIN values transmission . Matt chrome-plated blade with black tip . Hard core for lasting blade/handle connection even under the highest loads Technical data: . Blade made of CrV and CrMV (special alloy) . Surface: Chrome-plated

Width across fl ats 2 mm 2.5 mm 3 mm 3 mm 3 mm 3 mm 4 mm 4 mm Blade length (mm) 100 100 80 100 150 200 100 150 Ident. No. 700 710 720 722 724 726 730 732 52139... ● ● ● ● ● ● ● ● Width across fl ats 4 mm 5 mm 5 mm 5 mm 6 mm 6 mm 6 mm 8 mm Blade length (mm) 200 100 150 200 100 150 200 100 Ident. No. 734 740 742 744 750 752 754 760 52139... ● ● ● ● ● ● ● ● Width across fl ats 8 mm 8 mm 10 mm 10 mm Blade length (mm) 150 200 100 200 Ident. No. 762 764 770 772 52139... ● ● ● ● Prod. Gr. 590

Hexagonal screwdriver set with T-handle with 2-component handle

Execution: . Matt chrome-plated blade with Black-Tip . Comfortable non-slip so coating provides for . Blade lengths: 2x100 mm/2.5x100mm/3x100 optimal power transmission mm/4x150 mm/5x150 mm/6x200 mm/8x200 mm . Hard core for lasting blade/handle connection even under the highest loads Technical data: . Blade made of special CrV and CrMV alloy . Width across ﬂ ats: 2 mm | 2.5 mm | 3 mm | 4 mm 5 mm 6 mm 8 mm . Optimal performance data up to 100% above DIN | | | . Surface: Chrome-plated values

Ident. No. 810 52139... ● Prod. Gr. 590

Hexagon screwdrivers 3-C T-handle

Execution: . Handle geometry made from high-quality plastics . Blade made of chrome-vanadium steel with so gripping areas for excellent comfort with . Continuously hardened high torque transmission . Continuous blade for additional lateral drive Technical data: Advantage: . Surface: Chrome-plated . Blades for lateral drive for easy opening and tightening, in particular of rusted in, bonded or self-tapping screws

Width across ﬂ ats 2 mm 2.5 mm 3 mm 4 mm 5 mm 6 mm 8 mm 10 mm Blade length (mm) 100 100 100 150 150 150 200 200 Length (mm) 126 126 126 126 132 132 132 138 Ident. No. 100 110 120 130 140 150 160 170 52137... ● ● ● ● ● ● ● ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH 1310Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1310_EN_2018_KERN[21850834]-n.indd 1310 12/17/2018 3:35:53 PM Screwdrivers \ Hexagon and TORX screwdrivers

Hexagon screwdriver straight

Execution: . Makes it easier to insert the blade thanks to the . Blade made of chrome-vanadium steel rounded front edges . Continuously hardened . Better resistance to corrosion . Rounded front edges . With hanging eyelet Technical data: . Surface: Nickel-plated Advantage: . Ergonomic handle for comfortable handling

Width across fl ats 2 mm 2.5 mm 3 mm 3 mm 3 mm 4 mm 4 mm 4 mm Blade length (mm) 100 100 100 150 200 100 150 200 Length (mm) 125 125 125 175 225 125 175 225 Ident. No. 500 510 520 530 535 540 550 555 52139... ● ● ● ● ● ● ● ● Width across fl ats 5 mm 5 mm 5 mm 6 mm 6 mm 6 mm 8 mm 8 mm Blade length (mm) 100 150 200 100 150 200 100 150 Length (mm) 132 182 232 132 182 232 132 182 Ident. No. 560 570 575 580 590 595 600 610 52139... ● ● ● ● ● ● ● ● Width across fl ats 8 mm 10 mm 10 mm Blade length (mm) 200 100 200 Length (mm) 232 139 239 Ident. No. 615 620 625 52139... ● ● ● Prod. Gr. 590

Hexagon screwdriver set Straight, with ergonomic T-handle

Execution: Advantage: . Blade made of chrome-vanadium steel . Ergonomic handle for comfortable handling . Continuously hardened . Makes it easier to insert the blade thanks to the . Rounded front edges rounded front edges . With hanging eyelet . Better resistance to corrosion . Blade lengths: 2x100 mm/2.5x100mm/3x100 mm/4x150 mm/5x150 mm/6x200 mm/8x200 mm

Width across ﬂ ats 2 mm | 2.5 mm | 3 mm | 4 mm | 5 mm | 6 mm | 8 mm Surface Nickel-plated Ident. No. 800 52139... ● Prod. Gr. 590

Hexagon screwdrivers Straight, with T-handle

Application: . With hanging eyelet Ident. No. 080–165: For hexagon socket screws. . Ident. No. 340–380: VDE version with protection-insulated blade, according Ident. No. 340–380: For working on live components. to EN/IEC 60900:2004 Ident. No. 400–430: For high torques with small screw sizes. . Ident. No. 400–430: With quick-action rotary handle, burnished blade

Execution: Advantage: . Hardened . Better resistance to corrosion

Ident. No. 080–165 Ident. No. 340–380 Ident. No. 400–430

Width across ﬂ ats 2 mm 2.5 mm 2.5 mm 3 mm 3 mm 3 mm 4 mm 4 mm Blade length (mm) 100 100 200 100 150 200 100 150 Length (mm) 126 126 226 126 176 226 126 175 Surface Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated VDE certiﬁ ed ------Ident. No. 080 090 095 100 110 112 115 120 52138... ● ● ● ● ● ● ● ●

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1311 Availability subject to country specific rules and regulations.

1310_EN_2018_KERN[21850834]-n.indd 1311 12/17/2018 3:35:56 PM Screwdrivers \ Hexagon and TORX screwdrivers

Width across fl ats 4 mm 5 mm 5 mm 5 mm 6 mm 6 mm 6 mm 8 mm Blade length (mm) 200 100 150 200 100 150 200 100 Length (mm) 226 132 182 232 132 182 232 132 Surface Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated VDE certifi ed ------Ident. No. 122 125 128 129 130 135 137 140 52138... ● ● ● ● ● ● ● ● Width across fl ats 8 mm 8 mm 10 mm 10 mm 12 mm 4 mm 5 mm 6 mm Blade length (mm) 150 200 100 200 200 150 150 150 Length (mm) 182 232 138 238 238 176 182 182 Surface Nickel-plated Nickel-plated Nickel-plated Nickel-plated Nickel-plated VDE insulated VDE insulated VDE insulated VDE certifi ed - - - - - Yes Yes Yes Ident. No. 145 147 150 155 165 340 350 360 52138... ● ● ● ● ● ● ● ● Width across fl ats 8 mm 1.5 mm 2 mm 2.5 mm 3 mm Blade length (mm) 150 60 60 60 60 Length (mm) 182 95 95 95 95 Surface VDE insulated Burnished Burnished Burnished Burnished VDE certifi ed Yes - - - - Ident. No. 380 400 410 420 430 52138... ● ● ● ● ● Prod. Gr. 533

Hexagon screwdriver sets Straight with T-handle

Execution: . Ident. No. 199: Blade lengths: 2 x 100, 2.5 x 100, . With T-handle 3 x 100, 4 x 150, 5 x 150, 6 x 200, 8 x 200 mm . Blade made of chrome-vanadium steel Advantage: . Continuously hardened . Ident. No. 199: Workshop stand to hang up or . Bright nickel-plated place in upright position . Ident. No. 190: Blade lengths: 2 x 100, 2.5 x 100, 3 x 100, 3 x 150, 4 x 100, 4 x 150, 5 x 100, 5 x 150, Delivery: 6 x 100, 6 x 200, 8 x 150 mm Ident. No. 190: In box Ident. No. 199: With workshop stand

Width across ﬂ ats 2 mm | 2.5 mm | 3 mm | 4 2 mm | 2.5 mm | 3 mm | 4 mm | 5 mm | 6 mm | 8 mm mm | 5 mm | 6 mm | 8 mm Surface Chrome-plated Chrome-plated Ident. No. 190 Ident. No. 199 Number of pieces in assortment/set 11 7 Ident. No. 190 199 52138... ● ● Prod. Gr. 533

Hexagon screwdriver with Magic-Ring® Straight with ergonomic T-handle

Execution: . Makes it easier to remove countersunk screws and . With T-handle to insert screws into slanted or deep blind holes . Blade made of chrome-vanadium steel . Suitable for stainless steel, brass or other non-magnetic screws Advantage: . Excellent retention force thanks to robust, wear- Technical data: proof spring steel ring . Surface: Nickel-plated

Width across ﬂ ats 3 mm 4 mm 5 mm 6 mm 8 mm 10 mm Blade length (mm) 100 150 150 150 200 200 Length (mm) 126 176 182 182 232 238 Ident. No. 530 540 550 560 580 590 52138... ● ● ● ● ● ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH 1312Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1310_EN_2018_KERN[21850834]-n.indd 1312 12/17/2018 3:35:58 PM Screwdrivers \ Hexagon and TORX screwdrivers

Hexagon screwdriver set with Magic-Ring® straight with T-handle

Execution: . Makes it easier to remove countersunk screws and . With T-handle to insert screws into slanted or deep blind holes . Blade made of chrome-vanadium steel . Suitable for stainless steel, brass or other . Bright nickel-plated non-magnetic screws Advantage: Delivery: With workshop stand . Excellent retention force thanks to robust, wearproof spring steel ring

Width across ﬂ ats 3 mm | 4 mm | 5 mm | 6 mm | 8 mm | 10 mm Surface Nickel-plated Ident. No. 700 52138... ● Prod. Gr. 533 Hexagonal angled screwdriver set short version, with ball head

Execution: Technical data: . chromium-vanadium steel, fully hardened and . Width across ﬂ ats: 1.5 mm | 2 mm | 2.5 mm | 3 brushed chromium-plated. mm | 4 mm | 5 mm | 6 mm | 8 mm | 10 mm . Surface: Chrome-plated Advantage: . space-saving, compact holder . ball head enables screws to be tightened at angles of up to 25° Version Short Ident. No. 800 52140... ● Prod. Gr. 533 Hexagonal angled screwdriver short version, with ball head

Execution: . ball head enables screws to be tightened at angles . chromium-vanadium steel, fully hardened and of up to 25° brushed chromium-plated. Technical data: Advantage: . Surface: Chrome-plated . especially for screws that are diﬃ cult to access

Width across ﬂ ats 1.5 mm 2 mm 2.5 mm 3 mm 4 mm 5 mm 6 mm Limb length x limb length 2 46 x 15 mm 51 x 18 mm 57 x 20 mm 64 x 23 mm 72 x 29 mm 83 x 33 mm 94 x 38 mm Version Short Ident. No. 801 802 803 804 805 806 807 52140... ● ● ● ● ● ● ● Width across ﬂ ats 8 mm 10 mm Limb length x limb length 2 105 x 44 mm 119 x 50 mm Version Short Ident. No. 808 809 52140... ● ● Prod. Gr. 533 Hexagonal angled screwdriver Long versions, short arms

Execution: Advantage: . Hexagonal ball end on the long wrench side . Ball end enables screws to be tightened at angles . Shorter arm bent by 100° of up to 25° . Chrome-vanadium steel . Bent arm provides better accessibility . Hardened . Wrench is easy to remove . Chrome-plated Delivery: In functional plastic holder

1.5 mm | 2 mm | 2.5 mm | 3 Width across ﬂ ats mm | 4 mm | 5 mm | 6 mm | 8 mm | 10 mm Surface Nickel-plated Version Long Ident. No. 200 52137... ● Prod. Gr. 590

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1313 Availability subject to country specific rules and regulations.

1313_EN_2018_KERN[21850838]-r.indd 1313 12/17/2018 3:35:55 PM Screwdrivers \ Hexagon and TORX screwdrivers

Hexagonal angled screwdriver set Long version, coloured paint

Execution: Advantage: . Hexagonal ball end on the long wrench side . Ball end enables screws to be tightened at angles . Coated with wearproof powder paint of up to 25° . Chrome-vanadium steel . Colour coating ensures instant identiﬁ cation of the . Hardened wrench size . Wrench is easy to remove Delivery: In functional plastic holder

1.5 mm | 2 mm | 2.5 mm | 3 Width across ﬂ ats mm | 4 mm | 5 mm | 6 mm | 8 mm | 10 mm Surface Lacquered Version Long Ident. No. 001 52139... ● Prod. Gr. 590 Hexagonal angled screwdriver Long version

Execution: Advantage: . Hexagonal ball end on the long wrench side . Ball end enables screws to be tightened at angles . Chrome-vanadium steel of up to 25° . Hardened . Better resistance to corrosion

Technical data: . Surface: Nickel-plated

Width across ﬂ ats 1.5 mm 2 mm 2.5 mm 3 mm 4 mm 5 mm 6 mm Limb length x limb length 2 91.5 x 15.5 114.5 x 20.5 mm 102 x 18 mm mm 129 x 23 mm 144 x 29 mm 165 x 33 mm 186 x 38 mm Version Long Ident. No. 015 020 025 030 040 050 060 52139... ● ● ● ● ● ● ● Width across ﬂ ats 8 mm 10 mm 12 mm Limb length x limb length 2 208 x 44 mm 234 x 50 mm 162 x 57 mm Version Long Ident. No. 080 100 120 52139... ● ● ● Prod. Gr. 590

Hexagonal angled screwdriver set Long version

1.5 mm | 2 mm | 2.5 mm | 3 Width across ﬂ ats mm | 4 mm | 5 mm | 6 mm | 8 mm | 10 mm Surface Nickel-plated Version Long Ident. No. 900 52139... ● Prod. Gr. 590 ErgoStar hexagonal angled screwdriver set Long version, coloured paint

Execution: . Fluorescent, luminous coating ensures that . Hexagon ball head on the long wrench side individual wrenches are still easy to locate in dark . Chromium-vanadium steel areas . fully hardened Advantage: . Ergo-Star holder Incredibly easy removal and . ball head enables screws to be tightened at angles deﬁ ned insertion of up to 25° . Colour paint ensures instant identiﬁ cation of the wrench size

Source: Hahn+Kolb Werkzeuge GmbH 1314Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1313_EN_2018_KERN[21850838]-r.indd 1314 12/17/2018 3:35:58 PM Screwdrivers \ Hexagon and TORX screwdrivers

1.5 mm | 2 mm | 2.5 mm | 3 Width across ﬂ ats mm | 4 mm | 5 mm | 6 mm | 8 mm | 10 mm Surface Lacquered Version Long Ident. No. 690 52140... ● Prod. Gr. 533 Hexagon oﬀ set screwdriver sets Long version with ball head

Execution: . Makes it easier to remove countersunk screws . Chrome-vanadium steel and to insert screws into slanted or deep blind . Ident. No. 710: Hexagonal ball end with spring holes steel ring on the long wrench side . Suitable for stainless steel, brass or other non-magnetic screws Ident. No. 710 Ident. No. 750 . Ident. No. 750: shorter arm bent by 100° . Ident. No. 750: Advantage: . ball head enables screws to be tightened at . Ident. No. 710: angles of up to 25° . Save-spacing ErgoStar holder . bent arm provides better accessibility . Ball end enables screws to be tightened at angles . wrench is easy to remove of up to 30° Delivery: . MagicRing: excellent retention force thanks to Ident. No. 710: In ErgoStar holder robust, wear-resistant spring steel ring Ident. No. 750: In Pro-Star holder

1.5 mm | 2 mm | 2.5 Width across ﬂ ats mm | 3 mm | 4 mm | 5 mm | 6 mm | 8 mm | 10 mm Surface Chrome-plated Version ErgoStar/Magic Ring Long Ident. No. 710 52140... ● Short arm, bent 100° Long Ident. No. 750 52140... ● Prod. Gr. 533 Hexagonal angled screwdriver long version with ball head

Execution: Advantage: . Hexagonal ball end on the long wrench side . High level of corrosion protection . Chrome-vanadium steel . hardened and blackened

Width across ﬂ ats 1.5 mm 2 mm 2.5 mm 3 mm 4 mm 5 mm 6 mm Limb length x limb length 2 91 x 15 mm 101 x 18 mm 113 x 20 mm 128 x 23 mm 142 x 29 mm 163 x 33 mm 184 x 38 mm Version Long Ident. No. 015 020 025 030 040 050 060 52140... ● ● ● ● ● ● ● Width across ﬂ ats 8 mm 10 mm 12 mm Limb length x limb length 2 206 x 44 mm 231 x 50 mm 259 x 57 mm Version Long Ident. No. 080 100 120 52140... ● ● ● Prod. Gr. 533

Hexagon oﬀ set screwdriver sets Long version

Execution: Advantage: . Hexagonal ball end on the long wrench side . High level of corrosion protection . Chrome-vanadium steel . Ident. No. 200: Longer service lives thanks to . Ident. No. 200: manganese phosphate plating Ident. No. 200 . Hardened Ident. No. 210 . Manganese phosphate plated . Ident. No. 210: hardened, blackened

1.5 mm | 2 mm | 2.5 1.5 mm | 2 mm | 2.5 mm | 3 mm | 4 mm | Width across ﬂ ats mm | 3 mm | 4 mm | 5 mm | 6 mm | 8 mm 5 mm | 6 mm | 10 mm Surface Phosphated Phosphated Number of pieces in assortment/set 7 9 Version Long Ident. No. 200 210 52140... ● ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1315 Availability subject to country specific rules and regulations.

1313_EN_2018_KERN[21850838]-r.indd 1315 12/17/2018 3:35:59 PM Screwdrivers \ Hexagon and TORX screwdrivers

Hexagon angled screwdriver Long design, with Magic-Ring® ball head

Execution: . Excellent retention force thanks to robust, wear- . Hexagonal ball end with spring steel ring on the proof spring steel ring long wrench side . Makes it easier to remove countersunk screws and . Chrome-vanadium steel to insert screws into slanted or deep blind holes . Suitable for stainless steel, brass or other Advantage: non-magnetic screws . Ball end enables screws to be tightened at angles of up to 25° Technical data: . Surface: Chrome-plated

Width across ﬂ ats 3 mm 4 mm 5 mm 6 mm 8 mm 10 mm Limb length x limb length 2 129 x 23 mm 142 x 29 mm 163 x 33 mm 184 x 38 mm 206 x 44 mm 231 x 50 mm Version Long Ident. No. 430 440 450 460 480 500 52140... ● ● ● ● ● ● Prod. Gr. 533

Hexagon oﬀ set screwdriver sets Long version, WERA Hex-Plus proﬁ le

Execution: Advantage: Delivery: . Hexagonal ball end on the long wrench side . Hex-Plus profi le provides a larger contact surface In lockable plastic holder . Ident. No. 370–390: Continuous hexagon with reduced notch eff ect. Damage to the screw . Ident. No. 390: Short arms bent by 100° head is prevented while simultaneously achieving Technical data: up to 20% higher transmittable torque. . Width across fl ats: 1.5 mm 2 mm 2.5 mm . Ident. No. 400: Made completely from stainless | | | 3 mm 4 mm 5 mm 6 mm 8 mm 10 mm steel . Ball end profi le also enables slightly slanted screw | | | | | connections in hard-to-reach areas . Ident. No. 410: Colour plastic coating

Ident. No. 390 Ident. No. 370 Ident. No. 400 Ident. No. 410

Surface Nickel-plated Chrome-plated Bare Burnished Version Long Ident. No. 370 390 400 410 52139... ● ● ● ● Prod. Gr. 542

Hexagon angled screwdriver with pin

Application: Advantage: For RIBE CS screws. . Better resistance to corrosion

Execution: Technical data: . With pin . Surface: Nickel-plated . Chrome-vanadium steel . Hardened

Width across ﬂ ats 3 mm 4 mm 5 mm 6 mm 8 mm 10 mm 12 mm Limb length x limb length 2 66 x 23 mm 74 x 29 mm 85 x 33 mm 96 x 38 mm 108 x 44 mm 122 x 50 mm 137 x 57 mm Suitable for screw M4 M5 M6 M8 M10 M12 M14 Version Short Ident. No. 030 040 050 060 080 100 120 52144... ● ● ● ● ● ● ● Width across ﬂ ats 14 mm 17 mm 19 mm 22 mm Limb length x limb length 2 154 x 70 mm 177 x 80 mm 199 x 89 mm 222 x 102 mm Suitable for screw M16 | M18 M20 | M22 M24 | M27 M30 Version Short Ident. No. 140 170 190 220 52144... ● ● ● ● Prod. Gr. 532

Source: Hahn+Kolb Werkzeuge GmbH 1316Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1316_EN_2018_KERN[21850843]-r.indd 1316 12/17/2018 3:35:54 PM Screwdrivers \ Hexagon and TORX screwdrivers

Hexagon screwdriver with ball head straight

Execution: . 3-component power grip with large so area for . Hexagon ball end comfortable use and fatigue-free working . Blade made of chrome-vanadium steel . Hardened Technical data: . Version: Straight . 3-component power grip, with large so area . Surface: Chrome-plated Advantage: . Ball end enables screws to be tightened at angles of up to 30°

Width across ﬂ ats 2 mm 2.5 mm 3 mm 4 mm 5 mm 6 mm 8 mm 10 mm Blade length (mm) 100 100 100 100 100 125 150 150 Length (mm) 200 200 200 210 210 240 260 270 Ident. No. 021 026 031 041 051 061 081 101 52134... ● ● ● ● ● ● ● ● Prod. Gr. 590 Hexagon screwdriver set with ball head straight

Execution: Advantage: . Hexagon ball head . Ball end enables screws to be tightened at angles . Blade made of chrome-vanadium steel of up to 30° . Hardened . 3-component power grip with large so area for comfortable use and fatigue-free working

Width across ﬂ ats 3 mm | 4 mm | 5 mm | 6 mm | 8 mm Surface Chrome-plated Ident. No. 201 52134... ● Prod. Gr. 590 Hexagon screwdrivers straight

Execution: Technical data: . Hexagon ball end . Version: Straight . Blade made of chrome-vanadium steel . Surface: Chrome-plated . Wiha-Chromtop® tip Advantage: . Ball end enables screws to be tightened at angles of up to 30° . So Finish® handle for comfortable handling

Width across ﬂ ats 1.5 mm 2 mm 2.5 mm 3 mm 4 mm 5 mm 6 mm 8 mm 10 mm 12 mm Blade length (mm) 75 100 100 100 100 100 125 150 150 150 Length (mm) 179 204 204 204 211 211 243 268 271 271 Ident. No. 015 020 025 030 040 050 060 080 100 120 52141... ● ● ● ● ● ● ● ● ● ● Prod. Gr. 533 Hexagon screwdriver set straight

Execution: Advantage: . Hexagon ball head . Ball end enables screws to be tightened at angles . Blade made of chrome-vanadium steel of up to 30° . Hardened . So Finish® handle for comfortable handling . So Finish® handle . Wiha-Chromtop® tip

Width across ﬂ ats 2.5 mm | 3 mm | 4 mm | 5 mm | 6 mm | 8 mm Surface Chrome-plated Ident. No. 400 52141... ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1317 Availability subject to country specific rules and regulations.

1316_EN_2018_KERN[21850843]-r.indd 1317 12/17/2018 3:35:57 PM Screwdrivers \ Hexagon and TORX screwdrivers

Hexagon screwdriver with Magic-Ring Straight

Execution: . Excellent retention force thanks to robust, wear- . Hexagon ball end proof spring steel ring . With Magic-Ring® . Suitable for stainless steel, brass or other . Blade made of chrome-vanadium steel non-magnetic screws . So Finish® handle for comfortable handling Advantage: . Ball end enables screws to be tightened at angles Technical data: of up to 25° . Version: Straight . Surface: Chrome-plated

Width across ﬂ ats 3 mm 4 mm 5 mm 6 mm 8 mm 10 mm Blade length (mm) 100 100 100 125 150 150 Length (mm) 204 211 211 243 268 271 Ident. No. 203 204 205 206 208 210 52141... ● ● ● ● ● ● Prod. Gr. 533 Angled screwdriver For TORX® screws

Execution: Advantage: . High-alloy chrome-molybdenum steel . High level of corrosion protection . hardened and blackened Technical data: . Surface: Phosphated

Tip size TX5 TX6 TX7 TX8 TX9 TX10 TX15 TX20 Limb length x limb length 2 39 x 18 mm 41 x 18 mm 44 x 18 mm 47 x 18 mm 51 x 19 mm 54 x 20 mm 57 x 22 mm 62 x 23 mm Ident. No. 705 706 707 708 709 710 715 720 52142... ● ● ● ● ● ● ● ● Tip size TX25 TX27 TX30 TX40 TX45 TX50 TX55 TX60 Limb length x limb length 2 67 x 25 mm 72 x 27 mm 79 x 30 mm 86 x 33 mm 90 x 36 mm 104 x 41 mm 120 x 47 mm 134 x 52 mm Ident. No. 725 727 730 740 745 750 755 760 52142... ● ● ● ● ● ● ● ● Prod. Gr. 533

TX angled screwdriver set For TORX® screws

Execution: Advantage: . High-alloy chrome-molybdenum steel . High level of corrosion protection . hardened and blackened Delivery: In holder

Tip size TX9 | TX10 | TX15 | TX20 | TX25 | TX27 | TX30 | TX40 Number of pieces in assortment/set 8 Ident. No. 821 52142... ● Prod. Gr. 533

TX angled screwdriver set For internal TORX® screws, coloured paint

Execution: Advantage: . TX ball head on the long wrench side . Colour powder coating ensures instant identiﬁ ca- . Chrome-vanadium steel tion of wrench sizes . Coated with wearproof powder paint . Ball end also enables slightly slanted screw . Hardened connections in hard-to-reach areas Delivery: In functional plastic holder

Tip size TX9 | TX10 | TX15 | TX20 | TX25 | TX27 | TX30 | TX40 Surface Lacquered Number of pieces in assortment/set 8 Ident. No. 150 52146... ● Prod. Gr. 590

Source: Hahn+Kolb Werkzeuge GmbH 1318Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1318_EN_2018_KERN[21850846]-u.indd 1318 12/17/2018 3:35:53 PM Screwdrivers \ Hexagon and TORX screwdrivers

TX angled screwdriver set For internal TORX® screws

Execution: Delivery: . Chrome-vanadium steel In plastic slide box . Hardened . Steel grey

Tip size TX9 | TX10 | TX15 | TX20 | TX25 | TX27 | TX30 | TX40 Number of pieces in assortment/set 8 Ident. No. 200 52146... ● Prod. Gr. 590

TX angled screwdriver set For internal TORX® screws, extra-long version

Execution: Delivery: . Chrome-vanadium steel In plastic clip . Hardened . Steel grey

Tip size TX5 | TX6 | TX7 | TX8 | TX9 | TX10 | TX15 | TX20 | TX25 | TX27 | TX30 | TX40 | TX50 Number of pieces in assortment/set 13 Ident. No. 300 52146... ● Prod. Gr. 590

TX angled screwdriver set For internal TORX® screws, with hole in the drive tip

Execution: Delivery: . Chrome-vanadium steel In plastic clip . Hardened . Steel grey

Tip size TX9 | TX10 | TX15 | TX20 | TX25 | TX27 | TX30 | TX40 Number of pieces in assortment/set 8 Ident. No. 400 52146... ● Prod. Gr. 590

Angled screwdriver For internal TORX® screws, with ball head

Execution: . Hardened . Chrome-vanadium steel . Steel grey

Tip size TX9 TX10 TX15 TX20 TX25 TX27 TX30 TX40 Limb length x limb length 2 67 x 19 mm 76 x 20 mm 86 x 20 mm 98 x 22 mm 100 x 22 mm 111 x 25 mm 125 x 30 mm 139 x 33 mm Ident. No. 509 510 515 520 525 527 530 540 52146... ● ● ● ● ● ● ● ● Prod. Gr. 590

TX angled screwdriver set For internal TORX ® screws, with ball head

Execution: . Steel grey . Chrome-vanadium steel Delivery: . Hardened In plastic clip

Tip size TX9 | TX10 | TX15 | TX20 | TX25 | TX27 | TX30 | TX40 Number of pieces in assortment/set 8 Ident. No. 500 52146... ● Prod. Gr. 590

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1319 Availability subject to country specific rules and regulations.

1318_EN_2018_KERN[21850846]-u.indd 1319 12/17/2018 3:35:57 PM Screwdrivers \ Hexagon and TORX screwdrivers

Angled screwdriver sets For TORX® screws, long design

Execution: . Ident. No. 447: Retaining spring with covering disc Delivery: . Chrome-vanadium steel welded by laser on the blade tip Ident. No. 441: In ProStar sliding holder Ident. No. 445: Clamp holder with suspension hole . hardened and blackened throughout Advantage: Ident. No. 447: In ErgoStar holder . Ident. No. 441: Standard ﬁ nish . Ident. No. 441: High level of corrosion protection . Ident. No. 445: Magic-Spring retaining spring with . Ident. No. 445–447: Clamping function between covering disc welded by laser on the blade tip spring and screw prevents the screw from being Technical data: . Surface: Phosphated lost

Ident. No. 447 Ident. No. 441 Ident. No. 445

TX5 | TX6 | TX7 | TX8 | TX5 | TX6 | TX7 | TX8 | Tip size TX9 | TX10 | TX15 | TX20 | TX6 | TX7 | TX8 | TX9 | TX9 | TX10 | TX15 | TX20 | TX25 | TX27 | TX30 | TX40 TX10 | TX15 | TX20 TX25 | TX27 | TX30 | TX40 | TX50 | TX45 Number of pieces in assortment/set 13 7 13 Standard ﬁ nish Ident. No. 441 52142... ● - - With MagicSpring Ident. No. - 445 447 52142... ● ● Prod. Gr. 533 Oﬀ set screwdriver sets For TORX® screws, long design with ball head

Execution: . long service life and perfect ﬁ t accuracy on . High level of corrosion protection . Ident. No. 450–455: screw head . Ball end enables screws to be tightened at angles . Chrome-vanadium steel . lowers the risk of injury by increasing the usable of up to 25° . hardened and blackened throughout space by bending 95° . Ident. No. 460: ball head enables screws to be . Ball end on the long wrench side . T-handle wrench height reduced by up to 15% for tightened at angles of up to 25° . Ident. No. 460: improved accessibility . chromium-vanadium steel, brushed Delivery: Advantage: Clamp holder with suspension hole chromium-plated Ident. No. 450: . Ident. No. 450–455: Ident. No. 455: In ErgoStar holder

Ident. No. 455 Ident. No. 450 Ident. No. 460

TX5 | TX6 | TX7 | TX8 | TX5 | TX6 | TX7 | TX8 | Tip size TX9 | TX10 | TX15 | TX20 | TX9 | TX10 | TX15 | TX20 | TX9 | TX10 | TX15 | TX20 | TX25 | TX27 | TX30 | TX40 TX25 | TX27 | TX30 | TX40 TX25 | TX27 | TX30 | TX40 | TX45 | TX45 Surface Phosphated Phosphated Chrome-plated Number of pieces in assortment/set 8 13 13 With ball end Ident. No. 450 455 52142... ● ● - ball end Ident. No. - - 460 52142... ● Prod. Gr. 533 TX angled screwdriver set For TORX PLUS® screws, with MagicSpring®

Execution: Advantage: . Chrome-vanadium steel . High level of corrosion protection . hardened and blackened throughout . Clamping function between spring and screw . Retaining spring with covering disc welded by laser prevents the screw from being lost on the blade tip . TX PLUS with reinforced proﬁ le cross-section for . With hanging eyelet up to 25% higher transferable torques compared to standard TX

Tip size TXP6 | TXP7 | TXP8 | TXP9 | TXP10 | TXP15 | TXP20 Surface Phosphated Number of pieces in assortment/set 7 Ident. No. 500 52142... ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH 1320Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1320_EN_2018_KERN[21850849]-s.indd 1320 12/17/2018 3:35:56 PM Screwdrivers \ Hexagon and TORX screwdrivers

TX Allen key sets with a clamping function or with ball head for inner TORX screws

Delivery: Ident. No. 441: In ProStar sliding holder Ident. No. 445: Clamp holder with suspension hole Ident. No. 447: In ErgoStar holder Execution: . Ident. No. 002: . Multi-coloured hose coating, in two-component . Sizes TX 15-40 with ball head on the long wrench Technical data: clip side Ident. No. 001 Ident. No. 002 . Surface: Phosphated . BlackLaser surface . hole in the drive tip above size TX 10 . Holding clip ﬁ tted with magnetising device . Ident. No. 001: . TX proﬁ le with special mechanical holding function . Screws are held securely without magnetisation TX8 | TX9 | TX10 + P TX8 | TX9 | TX10 | | TX15 + P | TX20 + P Tip size TX15 | TX20 | TX25 | | TX25 + P | TX27 + P TX27 | TX30 | TX40 | TX30 + P | TX40 + P Number of pieces in assortment/set 9 9 with holding function Ident. No. 001 52147... ● - ball end Ident. No. - 002 52147... ● Prod. Gr. 542 Screwdriver For TORX® screws

Execution: Advantage: . Chrome-vanadium/molybdenum steel . 3-component power grip with large so area for . Continuously hardened comfortable use and fatigue-free working . Blackened tip . Better accuracy of ﬁ t with longer service life . 3-component power grip, with large so area Ident. No. 906–920 . With hole in the drive tip (T10-40) Technical data: . Surface: Chrome-plated

Ident. No. 925–940

Tip size TX6 TX7 TX8 TX9 TX10 + P TX15 + P TX20 + P TX25 + P TX27 + P TX30 + P TX40 + P Blade length (mm) 60 60 60 60 80 80 100 100 115 115 130 Length (mm) 146 146 146 157 170 180 207 207 234 234 249 Ident. No. 906 907 908 909 910 915 920 925 927 930 940 52144... ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 590

TX screwdriver sets For TORX® screws, with hole in the drive tip

Application: Advantage: For turning safety screws (centre pin in proﬁ le). . 3-component power grip with large so area for comfortable use and fatigue-free working Execution: . Better accuracy of ﬁ t with longer service life . Chrome-vanadium/molybdenum steel . Continuously hardened Technical data: . Matt chromium-plated . Surface: Chrome-plated . Blackened tip . 3-component power grip, with large so area TX10 + P | TX15 TX8 | TX9 | TX10 Tip size TX10 + P | TX15 TX6 | TX7 | TX8 + P | TX20 + P | + P | TX15 + P | + P | TX20 + P | TX9 | TX10 + P TX25 + P | TX30 TX20 + P | TX25 + P + P | TX30 + P Number of pieces in assortment/ set 3 5 5 7 Ident. No. 900 901 902 904 52144... ● ● ● ● Prod. Gr. 590

Screwdriver For TORX® screws

Execution: . So Finish handle with roll-away protection . Chrome-vanadium/molybdenum steel . Continuously hardened Technical data: . Surface: Chrome-plated . tip Wiha-Chromtop Tip size TX3 TX4 TX5 TX6 TX7 TX8 TX9 TX10 TX15 TX20 TX25 TX27 TX30 TX40 TX45 Blade length (mm) 60 60 60 60 60 60 60 80 80 100 100 115 115 130 130 Length (mm) 164 164 164 164 164 164 171 191 191 218 218 233 233 254 254 Ident. No. 203 204 205 206 207 208 209 210 215 220 225 227 230 240 245 52143... ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1321 Availability subject to country specific rules and regulations.

1320_EN_2018_KERN[21850849]-s.indd 1321 12/17/2018 3:35:58 PM Screwdrivers \ Hexagon and TORX screwdrivers

Screwdriver sets For TORX® screws

Execution: Technical data: . Chrome-vanadium/molybdenum steel . Surface: Chrome-plated . Continuously hardened . tip Wiha-Chromtop . So Finish handle with roll-away protection

Tip size TX10 | TX15 | TX20 | TX25 | TX8 | TX9 | TX10 | TX15 | TX30 | TX40 TX20 | TX25 | TX30 Number of pieces in assortment/set 6 7 Ident. No. 265 267 52143... ● ● Prod. Gr. 533 Ident. No. 265

Screwdrivers For TORX® screws, with MagicSpring®

Execution: Advantage: . Chrome-vanadium/molybdenum steel . Clamping function between spring and screw . Continuously hardened prevents the screw from being lost . tip Wiha-Chromtop . So Finish handle with roll-away protection Technical data: . Surface: Chrome-plated . Retaining spring with covering disc welded by laser on the blade tip

Tip size TX6 TX7 TX8 TX9 TX10 TX15 TX20 TX25 TX27 TX30 TX40 Blade length (mm) 60 60 60 60 80 80 100 100 115 115 130 Length (mm) 164 164 164 171 191 191 218 218 233 233 254 Ident. No. 806 807 808 809 810 815 820 825 827 830 840 52143... ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 533

TX screwdriver set For TORX® screws, with MagicSpring®

Execution: . Retaining spring with covering disc welded by laser . Chrome-vanadium/molybdenum steel on the blade tip . Continuously hardened Advantage: . tip Wiha-Chromtop . Clamping function between spring and screw . So Finish handle with roll-away protection prevents the screw from being lost

Tip size TX10 | TX15 | TX20 | TX25 | TX30 | TX40 Surface Chrome-plated Ident. No. 890 52143... ● Prod. Gr. 533

Screwdrivers For TORX® screws, with hole in the driving pin (Tamper Resistant = TR)

Application: Advantage: For turning safety screws (centre pin in proﬁ le). . Multi-component handle for greater comfort . Wiha-Chromtop for accurate working processes Execution: . Chrome-vanadium/molybdenum steel Technical data: . Continuously hardened . Surface: Chrome-plated . tip Wiha-Chromtop . So Finish handle with roll-away protection

Tip size TX7 TX8 TX9 TX10 + P TX15 + P TX20 + P TX25 + P TX27 + P TX30 + P TX40 + P Blade length (mm) 60 60 60 80 80 100 100 115 115 130 Length (mm) 164 164 171 191 191 211 211 233 233 254 Ident. No. 007 008 009 010 015 020 025 027 030 040 52143... ● ● ● ● ● ● ● ● ● ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH 1322Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1320_EN_2018_KERN[21850849]-s.indd 1322 12/17/2018 3:35:59 PM Screwdrivers \ Hexagon and TORX screwdrivers

Screwdrivers For TORX PLUS® screws

Execution: Technical data: . Chrome-vanadium/molybdenum steel . Surface: Chrome-plated . Continuously hardened . tip Wiha-Chromtop . So Finish handle with roll-away protection

Tip size TXP6 TXP7 TXP8 TXP9 TXP10 TXP15 TXP20 TXP25 TXP27 TXP30 Blade length (mm) 60 60 60 60 80 80 100 100 115 115 Length (mm) 164 164 164 171 191 191 218 218 233 233 Ident. No. 106 107 108 109 110 115 120 125 127 130 52143... ● ● ● ● ● ● ● ● ● ● Prod. Gr. 533

Screwdriver For TORX PLUS® screws, with MagicSpring®

Execution: . Retaining spring with covering disc welded by laser . Chrome-vanadium/molybdenum steel on the blade tip . Continuously hardened . Brushed chromium-plated Technical data: . Surface: Chrome-plated . tip Wiha-Chromtop . So Finish handle with roll-away protection

Tip size TXP6 TXP7 TXP8 TXP9 TXP10 TXP15 TXP20 TXP25 TXP27 TXP30 Blade length (mm) 60 60 60 60 80 80 100 100 115 115 Length (mm) 164 164 164 171 191 191 218 218 233 233 Ident. No. 146 147 148 149 150 155 160 165 167 170 52143... ● ● ● ● ● ● ● ● ● ● Prod. Gr. 533

TX screwdriver with T-handle with 2-component handle

Execution: . optimum performance data up to 100% above the . easy-grip so coating for optimum power DIN values transmission . matt chrome-plated blade with black tip . hard core for lasting blade/handle connection even under the highest loads Technical data: . blade made of CrV and CrMV (special alloy) . Surface: Chrome-plated

Tip size TX8 TX9 TX10 TX15 TX20 TX25 TX27 TX30 Blade length (mm) 100 100 100 100 100 100 100 100 Ident. No. 208 209 210 215 220 225 227 230 52147... ● ● ● ● ● ● ● ● Tip size TX40 TX45 Blade length (mm) 100 140 Ident. No. 240 245 52147... ● ● Prod. Gr. 590

TX screwdriver set, with T-handle with 2-component handle

Execution: Technical data: . easy-grip so coating for optimum power . Tip size: TX10 | TX15 | TX20 | TX25 | TX30 | TX40 transmission . Surface: Chrome-plated . hard core for lasting blade/handle connection even . Number of pieces in assortment/set: 6 under the highest loads . blade made of CrV and CrMV (special alloy) . optimum performance data up to 100% above the DIN values . matt chrome-plated blade with black tip

Ident. No. 300 52147... ● Prod. Gr. 590

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1323 Availability subject to country specific rules and regulations.

1323_EN_2018_KERN[21850853]-o.indd 1323 12/17/2018 3:35:53 PM Screwdrivers \ Hexagon and TORX screwdrivers

Screwdriver with ergonomically shaped T-handle for internal TORX® screws

Execution: Advantage: . Straight . Ergonomically adjusted to your hand for fatigue- . Ergonomic T-handle free working . Blade made of chrome-vanadium steel . Hardened Technical data: . Surface: Chrome-plated . Black tip . Hanging eyelet

Tip size TX8 TX9 TX10 TX15 TX20 TX25 TX27 TX30 TX40 TX45 TX50 Blade length (mm) 100 100 100 100 100 100 100 100 100 150 150 Length (mm) 125 125 125 125 132 132 132 132 132 189 189 Ident. No. 108 109 110 115 120 125 127 130 140 145 150 52147... ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 590 Screwdrivers With ﬂ ag handle, for TORX® screws

Execution: Advantage: . Blade made from molybdenum-vanadium steel . Improved resistance to corrosion thanks to . Continuously hardened burnishing process

Technical data: . Surface: Burnished

Tip size TX5 TX6 TX7 TX8 TX9 TX10 TX15 TX20 Blade length (mm) 19 19 19 19 24 24 28 28 Ident. No. 005 006 007 008 009 010 015 020 52142... ● ● ● ● ● ● ● ● Prod. Gr. 590

Screwdrivers With ﬂ ag handle, for TORX PLUS® screws

Execution: . TX PLUS with reinforced proﬁ le cross-section for . Blade made from molybdenum-vanadium steel up to 25% higher transferable torques compared to . Continuously hardened standard TX Advantage: Technical data: . Improved resistance to corrosion thanks to . Surface: Burnished burnishing process Tip size TXP5 TXP6 TXP7 TXP8 TXP9 TXP10 TXP15 TXP20 Blade length (mm) 19 19 19 19 24 24 28 28 Ident. No. 105 106 107 108 109 110 115 120 52142... ● ● ● ● ● ● ● ● Prod. Gr. 590

MORE THAN 60,000 PRODUCTS FOR MAXIMUM INNOVATION.

WE HAVE WHAT IT TAKES.

For a complete range of products that meet the toughest demands, visit www.iconridge.com

Source: Hahn+Kolb Werkzeuge GmbH 1324Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1323_EN_2018_KERN[21850853]-o.indd 1324 12/17/2018 3:35:56 PM Screwdrivers \ Hexagon and TORX screwdrivers

Screwdriver For TORX® screws

Execution: . Ident. No. 305–320: With key handle . Blade made of chrome-vanadium steel . Ident. No. 410–450: . Continuously hardened . With T-handle . tip Wiha-Chromtop

Ident. No. 305–320

Ident. No. 410–450 Tip size TX5 TX6 TX7 TX8 TX9 TX10 TX15 TX20 Blade length (mm) 35 35 35 40 40 40 45 45 Length (mm) 70 70 70 75 75 75 80 80 Surface Burnished Burnished Burnished Burnished Burnished Burnished Burnished Burnished Ident. No. 305 306 307 308 309 310 315 320 52143... ● ● ● ● ● ● ● ● Tip size TX10 TX15 TX20 TX25 TX27 TX30 TX40 TX50 Blade length (mm) 100 100 100 100 100 100 200 250 Length (mm) 126 126 132 132 132 132 232 288 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Ident. No. 410 415 420 425 427 430 440 450 52143... ● ● ● ● ● ● ● ● Prod. Gr. 533

Screwdriver with 2-C T-handle and side drive For TORX® screws

Tip size TX10 TX15 TX20 TX25 TX27 TX30 TX40 Blade length (mm) 100 100 100 150 150 150 150 Length (mm) 126 126 132 132 132 132 132 Ident. No. 710 715 720 725 727 730 740 52143... ● ● ● ● ● ● ● Prod. Gr. 533

Screwdrivers For TORX® screws, with MagicSpring®

Execution: Advantage: . With T-handle . Clamping function between spring and screw . Blade made of chrome-vanadium steel prevents the screw from being lost . Continuously hardened . tip Wiha-Chromtop

Tip size TX9 TX10 TX15 TX20 TX25 TX27 TX30 TX40 Blade length (mm) 100 100 100 100 100 100 100 100 Length (mm) 126 126 126 126 132 132 132 132 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Ident. No. 459 460 465 470 475 477 480 490 52143... ● ● ● ● ● ● ● ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1325 Availability subject to country specific rules and regulations.

1325_EN_2018_KERN[21850856]-o.indd 1325 12/17/2018 3:35:53 PM Screwdrivers \ Hexagon and TORX screwdrivers

TX screwdriver set For TORX® screws, with MagicSpring®

Execution: Advantage: . With T-handle and blade hardened throughout . Clamping function between spring and screw . Blade made of chrome-vanadium steel prevents the screw from being lost . MagicSpring for TX10 to TX40 (not for TX50) . tip Wiha-Chromtop . In workshop stand

Tip size TX10 | TX15 | TX20 | TX25 | TX30 | TX40 | TX50 Surface Chrome-plated Number of pieces in assortment/set 7 Ident. No. 495 52143... ● Prod. Gr. 533

Screwdrivers For TORX PLUS® screws

Application: Advantage: Suitable for tools with cemented carbide reversible . TX PLUS with reinforced proﬁ le cross-section for tips. up to 25% higher transferable torques compared to standard TX Execution: . With key handle Technical data: . Blade made of chrome-vanadium steel . Surface: Burnished . Continuously hardened . blackened

Tip size TXP5 TXP6 TXP7 TXP8 TXP9 TXP10 TXP15 TXP20 Blade length (mm) 35 35 35 40 40 40 45 45 Length (mm) 70 70 70 75 75 75 80 80 Ident. No. 505 506 507 508 509 510 515 520 52143... ● ● ● ● ● ● ● ● Prod. Gr. 533

TX screwdriver set For TORX PLUS® screws

Execution: Advantage: . With key handle . TX PLUS with reinforced proﬁ le cross-section for . Blade made of chrome-vanadium steel up to 25% higher transferable torques compared to . In workshop stand standard TX

Tip size TXP6 | TXP7 | TXP8 | TXP9 | TXP10 | TXP15 | TXP20 Surface Burnished Number of pieces in assortment/set 7 Ident. No. 590 52143... ● Prod. Gr. 533

Permanent magnetiser and demagnetiser

Application: Execution: For magnetising and de-magnetising steel tool . ABS plastic housing blades. Height (mm) 50 Length (mm) 52 Depth (mm) 29 Ident. No. 010 52650... ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH 1326Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1325_EN_2018_KERN[21850856]-o.indd 1326 12/17/2018 3:35:54 PM Screwdrivers \ Slotted and Phillips screwdrivers

Slotted and Phillips PH screwdriver set with rotating cap, quick turn zone and plastic stand

Execution: Advantage: . High-alloy, chrome-vanadium/molybdenum steel . PicoFinish grip for precise and quick bolting blade . Plastic stand to hang up or place in upright position . Continuously hardened . Matt chromium-plated . Wiha-Chromtop® tip Supplied blade widths: 1.5 mm/2 mm/2.5 Composition of set mm/3 mm Tip size PH00 | PH0 Ident. No. 010 52673... ● Prod. Gr. 533

VDE precision screwdriver set, PicoFinish electric 6 piece

Execution: Technical data: . slim handle shape and rotary cap for sensitive work . Composition of set: blade widths supplied: . every part individually tested at 10,000 V AC and 1.5 mm/2 mm/2.5 mm/3 mm approved for 1000 V AC . Tip size: PH00 | PH0

Ident. No. 100 52675... ● Prod. Gr. 533

Hexagonal screwdriver or socket wrench set Rotating cap, quick turn zone and plastic stand

Application: . Ident. No. 010: Ideal for delicate screwing tasks . Hexagon socket at 0.9 mm, from 1.3 mm with hexagon socket ball end Execution: . Wiha-Chromtop® for accurate work . PicoFinish grip for precise and quick bolting . Ball head enables screws to be tightened at . Plastic stand to hang up or place in upright position angles of up to 25° . Ident. No. 020: External hexagon socket wrench Surface - Chrome-plated Width across ﬂ ats 0.9 mm | 1.3 mm | 1.5 mm | 2.5 mm | 3 mm | 3.5 mm | 4 2 mm | 2.5 mm | 3 mm mm | 5 mm | 5.5 mm Ident. No. 010 020 52675... ● ● Prod. Gr. 533

Slot head screwdriver ESD Precision handle

Execution: . “Black Tip” tip for precise ﬁ t . Precision screwdriver with rotary cap . Handle top with roll-oﬀ protection . 2-component handle technology with comfortable, . Blade produced from special chrome molybdenum non-slip so coating vanadium alloy with optimal performance data up to 100% above DIN values Width of cutting edge (mm) 2.5 3.0 Thickness of cutting edge (mm) 0.4 0.5 Blade length 60 60 Length 162 162 Material of the grip handle 2-component plastic 2-component plastic Ident. No. 025 030 52689... ● ● Prod. Gr. 590

ESD Phillips screwdriver With precision handle

Execution: . “Black Tip” tip for precise ﬁ t . Precision screwdriver with rotary cap . Handle top with roll-oﬀ protection . 2-component handle technology with comfortable, . Blade produced from special chrome molybdenum non-slip so coating vanadium alloy with optimal performance data up to 100% above DIN values Tip size PH0 PH1 Blade length (mm) 60 75 Length (mm) 162 177 Material of the grip handle 2-component plastic 2-component plastic Ident. No. 110 120 52689... ● ● Prod. Gr. 590 Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1327 Availability subject to country specific rules and regulations.

1327_EN_2018_KERN[21850859]-v.indd 1327 12/17/2018 3:35:54 PM Screwdrivers \ Slotted and Phillips screwdrivers

ESD hexagonal socket screwdrivers Precision handle

Execution: . Blade produced from special chrome molybdenum . Precision screwdriver with rotary cap vanadium alloy with optimal performance data up . 2-component handle technology with comfortable, to 100% above DIN values non-slip so coating . Handle top with roll-oﬀ protection Width across ﬂ ats 1.5 mm 2 mm 2.5 mm 3 mm Blade length (mm) 60 60 75 75 Length (mm) 162 162 177 177 Ident. No. 215 220 225 230 52689... ● ● ● ● Prod. Gr. 590 Slot head screwdriver ESD Precision handle

Width of cutting edge (mm) 1.5 2 2.5 3 3.5 4 Thickness of cutting edge (mm) 0.25 0.4 0.4 0.5 0.6 0.8 Blade length (mm) 40 40 50 50 60 60 Length (mm) 120 120 145 145 170 170 Ident. No. 200 210 220 230 240 250 52690... ● ● ● ● ● ● Prod. Gr. 533 ESD Phillips screwdriver With precision handle

Application: . Matt chromium-plated For working on potentially electrostatic components . Wiha-Chromtop® tip (IEC 61340-5-1). . Precision handle with impact-resistant plastic rotary cap Execution: . High-alloy, chrome-vanadium/molybdenum steel Technical data: blade . Material of the grip handle: 1-component plastic . Continuously hardened Tip size PH00 PH0 PH1 PZ1 Blade length (mm) 40 50 60 60 Length (mm) 120 145 170 170 Ident. No. 300 310 320 350 52690... ● ● ● ● Prod. Gr. 533 ESD hexagonal screwdriver Precision handle

Application: . Matt chrome-plated and continuously hardened For working on potentially electrostatic components . Wiha-Chromtop® tip (IEC 61340-5-1). . Precision handle with impact-resistant plastic rotary cap Execution: . High-alloy, chrome-vanadium/molybdenum steel Technical data: blade . Version: Straight . Hexagon socket driver . Surface: Chrome-plated Width across ﬂ ats 0.7 mm 0.9 mm 1.3 mm 1.5 mm 2 mm 2.5 mm 3 mm Blade length (mm) 40 40 40 50 50 60 60 Length (mm) 120 120 120 145 145 170 170 Ident. No. 397 399 400 410 420 430 440 52690... ● ● ● ● ● ● ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH 1328Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1327_EN_2018_KERN[21850859]-v.indd 1328 12/17/2018 3:35:55 PM Screwdrivers \ Slotted and Phillips screwdrivers

ESD TX screwdriver Precision handle

Application: . Precision handle with impact-resistant plastic For working on potentially electrostatic components rotary cap (IEC 61340-5-1). . Surface resistance: 10^6 - 10^9 Ohm Execution: Advantage: . High-alloy, chrome-vanadium/molybdenum steel . Wiha-Chromtop for accurate working processes blade . Discharges electrostatic . Continuously hardened . Matt chromium-plated Technical data: . tip Wiha-Chromtop . Surface: Chrome-plated

Tip size TX3 TX4 TX5 TX6 TX7 TX8 TX9 TX10 Blade length (mm) 40 40 40 40 40 40 50 50 Length (mm) 120 120 120 120 120 120 145 145 Ident. No. 693 694 700 710 720 730 740 750 52690... ● ● ● ● ● ● ● ● Prod. Gr. 533 Li er for ESD components Precision handle

Application: . Continuously hardened For removing tightly seated components on PCBs. . Matt chromium-plated . Impact-resistant plastic precision handle Execution: . High-alloy, chrome-vanadium/molybdenum steel blade Fork width (inner) (mm) 3.5 Blade length (mm) 50 Length (mm) 145 Ident. No. 800 52690... ● Prod. Gr. 533 ESD slotted and Phillips PH screwdriver set Precision handle

Application: . Continuously hardened For working on potentially electrostatic components . Matt chromium-plated (IEC 61340-5-1). . Wiha-Chromtop® tip Execution: . Precision handle with impact-resistant plastic rotary cap . High-alloy, chrome-vanadium/molybdenum steel blade . With plastic stand

Composition of set Supplied blade widths: 1.5 mm/2 mm/2.5 mm/3 mm Tip size PH00 | PH0 Ident. No. 900 52690... ● Prod. Gr. 533

Kra form Kompakt micro set 11-piece

Application: . roll-away protection and rotatable cap, for extremely precise screwing tasks multi-component . extra slim 4 mm bits with half moon drive Blade set with standard Execution: handle . Kra form Micro ESD bit holder with quick-change Delivery: chuck in folding fabric bag Composition of set Supplied blade widths: 1.5 mm/2 mm/3 mm Width across ﬂ ats 1.5 mm | 2 mm Tip size PH00 | PH0 | PH1 | TX5 | TX6 Ident. No. 005 52208... ● Prod. Gr. 542

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1329 Availability subject to country specific rules and regulations.

1329_EN_2018_KERN[21850862]-p.indd 1329 12/17/2018 3:35:53 PM Screwdrivers \ Slotted and Phillips screwdrivers

Kra form Micro electronics screwdriver 12 pieces

Application: Advantage: for slotted and cross-head screws Phillips-Recess, . Black Point tip for longer service life and enhanced internal TX screws, hexagon socket screws. protection against corrosion . Fold-up pouch suitable for being fastened to a belt Execution: . Rotating cap Delivery: . Rotary zone with integrated so zones In fold-up pouch . Black Point tip Supplied blade widths: 1.5 mm/18 mm/2 Composition of set mm/2.5 mm/3 mm Width across ﬂ ats 1.5 mm | 2 mm Tip size PH00 | PH0 | PH1 | TX5 | TX6 Ident. No. 010 52695... ● Prod. Gr. 542 Watchmaker’s screwdriver set

Execution: . Blades made from chrome-vanadium steel Technical data: . Nickel-plated . Number of pieces in assortment/set: 6 . Similar to DIN 8331 Supplied blade widths: 1 mm/15 blade widths supplied: Composition of set mm/2 mm/25 mm/3 1.5 mm/2 mm/2.5 mm/3.5 mm mm/3.0 mm Tip size - PH000 | PH0 In wooden box Ident. No. 020 040 52708... ● ● In plastic case Ident. No. 030 52708... ● - Prod. Gr. 580

Spiral screwdriver

Application: . Ratchet bushing made from wearproof special For quicker bolting than with commercially available bronze screwdrivers. . Coated drill spindle . Locking ring for loosening and locking the spindle Execution: . Quick-change chuck for 1/2” bits . Bit magazine integrated in handle . PHZ bits suitable for PH and PZ . Reversible right/le ratchet Bit holder 1/4 inch hexagon Drive 1/4 inch Length (mm) 330 Tip size PH1 + slot | PH2 + slot | PH3 + slot | TX15 | TX20 | TX25 Ident. No. 010 52715... ● Prod. Gr. 580 Slotted screwdrivers with hexagonal blades ( DIN 5264 )

Execution: Advantage: . Chrome-vanadium/molybdenum steel blade . 3-component power grip with large so area for . Continuously hardened comfortable use and fatigue-free working . Matt chromium-plated . Better accuracy of ﬁ t with longer service life . Blackened tip . Steel blue/black Technical data: . Material of the grip handle: 3-component plastic . Ident. No. 036–046: Without hexagonal shoulder for wrenches . Ident. No. 056–121: With hexagonal shoulder for wrenches

Width of cutting edge (mm) 3.5 4.5 5.5 6.5 8.0 10.0 12.0 Thickness of cutting edge (mm) 0.6 0.8 1 1.2 1.2 1.6 2 Blade length (mm) 75 90 100 125 150 175 200 Length (mm) 186 197 209 245 269 297 320 Ident. No. 036 046 056 066 081 101 121 52751... ● ● ● ● ● ● ● Prod. Gr. 590

Source: Hahn+Kolb Werkzeuge GmbH 1330Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1329_EN_2018_KERN[21850862]-p.indd 1330 12/17/2018 3:35:57 PM Screwdrivers \ Slotted and Phillips screwdrivers

Screwdriver with hexagonal blade sets ( DIN 5264 )

Execution: . With hexagonal shoulder for wrenches (from a . Chrome-vanadium/molybdenum steel blade width of 5.5 mm) . Continuously hardened Advantage: . Matt chromium-plated . 3-component power grip with large so area for . Blackened tip comfortable use and fatigue-free working . Steel blue/black . Better accuracy of ﬁ t with longer service life

Supplied blade widths: Supplied blade widths: Supplied blade widths: Ident. No. 361 3.5 mm/4.5 mm/5.5 Composition of set 4.5 mm/5.5 mm/6.5 55 mm/6.5 mm/8 mm/6.5 mm/8 mm/8 mm mm mm/10 mm Number of pieces in assortment/set 6 6 8 PH1 | PH2 | PH3 | Tip size - PH1 | PH2 PZ1 | PZ2 Ident. No. 351 361 381 52751... ● ● ● Prod. Gr. 590 Phillips screwdriver with hexagonal blade ( ISO 8764 ) with PH and PZ drives

Execution: Advantage: . Chrome-vanadium/molybdenum steel blade . 3-component power grip with large so area for . Continuously hardened comfortable use and fatigue-free working . Matt chromium-plated . Better accuracy of ﬁ t with longer service life . Blackened tip . Steel blue/black Technical data: . Material of the grip handle: 3-component plastic . With hexagonal shoulder for wrenches Tip size PH1 PH2 PH3 PZ1 PZ2 PZ3 Blade length (mm) 80 100 150 80 100 150 Length (mm) 187 219 269 187 219 269 Ident. No. 501 502 503 601 602 603 52751... ● ● ● ● ● ● Prod. Gr. 590

Phillips screwdriver with hexagonal blade sets ( ISO 8764 )

Execution: . With hexagonal shoulder for wrenches . Chrome-vanadium/molybdenum steel blade Advantage: . Continuously hardened . 3-component power grip with large so area for . Matt chromium-plated comfortable use and fatigue-free working Ident. No. 700 . Blackened tip . Better accuracy of ﬁ t with longer service life . Steel blue/black

Tip size PH1 | PH2 | PH3 PZ1 | PZ2 | PZ3 Ident. No. 700 710 52751... ● ● Prod. Gr. 590 Slotted screwdrivers with circular blade ( DIN 5264 )

Execution: Advantage: . Blade made of chrome-vanadium steel . 3-component power grip with large so area for comfortable use and fatigue-free working . Continuously hardened Ident. No. 350–365 Technical data: . Material of the grip handle: 3-component plastic

Width of cutting edge (mm) 2.5 3.0 3.5 4.0 4.5 5.0 5.5 5.5 6.0 6.5 8.0 10.0 Thickness of cutting edge (mm) 0.4 0.5 0.5 0.8 0.8 0.9 1 1 1.1 1.2 1.2 1.6 Blade length (mm) 75 80 100 100 100 100 125 200 150 150 175 200 Length (mm) 161 166 197 207 207 207 232 307 269 269 294 319 Ident. No. 325 330 335 340 345 350 355 357 360 365 380 400 52752... ● ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 590

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1331 Availability subject to country specific rules and regulations.

1331_EN_2018_KERN[21850866]-r.indd 1331 12/17/2018 3:35:57 PM Screwdrivers \ Slotted and Phillips screwdrivers

Screwdriver with circular blade sets ( DIN 5264 )

Supplied blade widths: Supplied blade widths: Supplied blade widths: 3 mm/4 mm/5.5 Composition of set 4 mm/5.5 mm/6.5 4 mm/5.5 mm/6.5 mm/6.5 mm/8 mm/8 mm mm/8 mm mm/10 mm Ident. No. 411 Tip size - PH1 | PH2 PZ1 | PZ2 Ident. No. 410 411 412 52752... ● ● ● Prod. Gr. 590

Phillips screwdrivers with circular blades ( DIN 5264 ) with PH and PZ drives

Execution: Advantage: . Blade made of chrome-vanadium steel . 3-component power grip with large so area for . Continuously hardened comfortable use and fatigue-free working . 3-component power grip, with large so area Technical data: . Material of the grip handle: 2-component plastic

Tip size PH0 PH1 PH2 PH3 PZ0 PZ1 PZ2 PZ3 Blade length (mm) 60 80 100 150 60 80 100 150 Length (mm) 146 187 219 269 146 187 219 269 Ident. No. 500 501 502 503 600 601 602 603 52752... ● ● ● ● ● ● ● ● Prod. Gr. 590

Phillips screwdriver with circular blade sets ( DIN 5264 )

Execution: Advantage: . Blade made of chrome-vanadium steel . 3-component power grip with large so area for . Continuously hardened comfortable use and fatigue-free working

Tip size PH1 | PH2 | PH3 PZ1 | PZ2 | PZ3 Ident. No. 700 Ident. No. 700 710 52752... ● ● Prod. Gr. 590

Stubby slotted screwdriver ( DIN 5264 ) Short version with circular blade

Application: . Wiha-Chromtop® tip For screwdriving tasks in tight spaces. . So Finish® handle with roll-oﬀ protection Execution: Advantage: . Chrome-vanadium/molybdenum steel blade . Multi-component handle for greater comfort . Continuously hardened . Wiha-Chromtop® for accurate working processes . Matt chromium-plated Width of cutting edge (mm) 4 5.5 6.5 8 Thickness of cutting edge (mm) 0.8 1 1.2 1.2 Blade length (mm) 25 25 25 25 Length (mm) 81 81 81 81 2-component 2-component 2-component 2-component Material of the grip handle plastic plastic plastic plastic Ident. No. 040 055 065 080 52733... ● ● ● ● Prod. Gr. 533

Slotted screwdrivers ( DIN 5264 ) Circular blade

Execution: Advantage: . Chrome-vanadium/molybdenum steel blade . Multi-component handle for greater comfort . Continuously hardened . Wiha-Chromtop® for accurate working processes . Matt chromium-plated . Wiha-Chromtop® tip Technical data: . Material of the grip handle: 2-component plastic . So Finish® handle with roll-oﬀ protection

Source: Hahn+Kolb Werkzeuge GmbH 1332Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1331_EN_2018_KERN[21850866]-r.indd 1332 12/17/2018 3:36:04 PM Screwdrivers \ Slotted and Phillips screwdrivers

Width of cutting edge (mm) 2 2.5 3 3 3 3 3.5 4 Thickness of cutting edge (mm) 0.4 0.4 0.5 0.5 0.5 0.5 0.6 0.8 Blade length (mm) 65 75 80 100 150 200 100 100 Length (mm) 169 179 184 204 254 304 204 211 Ident. No. 100 110 115 116 117 118 120 130 52736... ● ● ● ● ● ● ● ● Width of cutting edge (mm) 4 4 4 4.5 5.5 5.5 5.5 5.5 Thickness of cutting edge (mm) 0.8 0.8 0.8 0.8 1 1 1 1 Blade length (mm) 150 200 300 125 125 150 200 300 Length (mm) 261 311 411 236 236 261 311 411 Ident. No. 131 132 133 135 140 141 142 143 52736... ● ● ● ● ● ● ● ● Width of cutting edge (mm) 6.5 6.5 6.5 8 8 8 10 12 Thickness of cutting edge (mm) 1.2 1.2 1.2 1.2 1.2 1.6 1.6 2 Blade length (mm) 100 150 200 150 175 175 200 250 Length (mm) 218 268 318 274 299 299 324 374 Ident. No. 144 150 151 155 160 165 170 180 52736... ● ● ● ● ● ● ● ● Width of cutting edge (mm) 14 Thickness of cutting edge (mm) 2.5 Blade length (mm) 250 Length (mm) 374 Ident. No. 190 52736... ● Prod. Gr. 533

ARE YOU LOOKING FOR PRODUCTS THAT MEET THE TOUGHEST DEMANDS?

WE HAVE WHAT IT TAKES.

For a complete range of products that meet the toughest demands, visit www.iconridge.com

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1333 Availability subject to country specific rules and regulations.

1331_EN_2018_KERN[21850866]-r.indd 1333 12/17/2018 3:36:04 PM Screwdrivers \ Slotted and Phillips screwdrivers

So Finish screwdriver set Circular blade

Application: . Ident. No. 250: Ident. No. 250: particularly suitable for dry . chromium-vanadium-molybdenum steel blade applications . fully hardened . brushed chromium-plated Execution: . So Finish® handle with roll-oﬀ protection Advantage: . Ident. No. 210: . Ident. No. 210: . Chrome-vanadium/molybdenum steel blade . Multi-component handle for greater comfort . Continuously hardened . Wiha-Chromtop® for accurate working . Matt chromium-plated processes

Composition of set Supplied blade widths: 3.5 blade widths supplied: 3.5 mm/45 mm/5.5 mm/65 mm mm/4.0 mm/6.5 mm Ident. No. 210 Number of pieces in assortment/set 6 12 PH1 | PH2 | PH3 | PZ1 | PZ2 Tip size PH1 | PH2 | TX15 | TX20 | TX25 | TX30 Ident. No. 210 250 52736... ● ● Prod. Gr. 533

Slotted screwdrivers with hexagonal blades ( DIN 5264 )

Execution: Advantage: . Chrome-vanadium/molybdenum steel blade . Multi-component handle for greater comfort . Continuously hardened . Wiha-Chromtop® for accurate working processes . Matt chromium-plated . Hexagonal shoulder for use with a wrench . Wiha-Chromtop® tip . So Finish® handle with roll-oﬀ protection Technical data: . Material of the grip handle: 2-component plastic . Hexagonal blade and hexagonal shoulder Width of cutting edge (mm) 3.5 4.5 5.5 6.5 8 10 12 14 Thickness of cutting edge (mm) 0.6 0.8 1 1.2 1.2 1.6 2 2.5 Blade length (mm) 75 90 100 125 150 175 200 250 Length (mm) 186 201 213 238 268 293 318 368 Ident. No. 110 120 130 140 150 160 170 180 52737... ● ● ● ● ● ● ● ● Prod. Gr. 533

Screwdriver with hexagonal blade set ( DIN 5264 )

Composition of set Supplied blade widths: 3.5 mm/45 mm/5.5 mm/7 mm Number of pieces in assortment/set 6 Tip size PH1 | PH2 Ident. No. 410 52737... ● Prod. Gr. 533 Slotted screwdrivers With circular or hexagonal blade

Application: . Solid steel cap For damp and oily screwing tasks. . Cellulose acetate handle . Impact-resistant Execution: Ident. No. 005–100 . Continuously hardened Advantage: . Matt chromium-plated . Wiha-Chromtop® for accurate working processes . Wiha-Chromtop® tip . Non-slip handle for excellent force transfer and secure handling . MicroFinish® handle with roll-oﬀ protection and non-slip surface texture . Ident. No. 300–340: . Steel cap for use as a chisel Ident. No. 300–340 . Black/magenta . Hexagonal shoulder for use with a wrench . Ident. No. 005–100: Round blade made from chrome-vanadium/molybdenum steel Technical data: . Ident. No. 300–340: . Material of the grip handle: 2-component plastic . Hexagonal blade with hexagonal shoulder made from chrome-vanadium/molybdenum steel

Source: Hahn+Kolb Werkzeuge GmbH 1334Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1331_EN_2018_KERN[21850866]-r.indd 1334 12/17/2018 3:36:05 PM Screwdrivers \ Slotted and Phillips screwdrivers

Width of cutting edge (mm) 3.5 4.0 4.0 5.5 5.5 6.5 8.0 8.0 10.0 4.5 5.5 6.5 8.0 10.0 Thickness of cutting edge (mm) 0.6 0.8 0.8 1 1 1.2 1.2 1.2 1.6 0.8 1 1.2 1.2 1.6 Blade length (mm) 100 100 150 125 150 150 150 175 200 90 100 125 150 175 Length (mm) 204 211 261 236 261 268 274 299 324 201 213 238 271 296 Ident. No. 005 010 020 040 050 070 080 090 100 300 310 320 330 340 52739... ● ● ● ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 533 Slotted and Phillips screwdriver sets With circular or hexagonal blade

Application: . Cadmium-free For damp and oily screwing tasks. . Ident. No. 425: . Hexagonal blade with hexagonal shoulder made Execution: from chrome-vanadium/molybdenum steel . Continuously hardened . Solid steel cap . Matt chromium-plated . Cellulose acetate handle . Wiha-Chromtop® tip . Impact-resistant . MicroFinish® handle with roll-oﬀ protection and Advantage: non-slip surface texture Ident. No. 405 Ident. No. 425 . Wiha-Chromtop® for accurate working processes . Black/magenta . Non-slip handle for excellent force transfer and . Ident. No. 405: secure handling . Round blade made from chrome-vanadium/ molybdenum steel Supplied blade widths: 3.5 Supplied blade widths: 5.5 Composition of set mm/4 mm/5.5 mm/65 mm mm/6.5 mm/8 mm Number of pieces in assortment/set 6 5 Tip size PH1 | PH2 PH1 | PH2 Ident. No. 405 425 52739... ● ● Prod. Gr. 533 Cross-point PH screwdrivers ( ISO 8764 ) For PHILLIPS-RECESS screws

Application: . Ident. No. 110–410: Hexagonal blade with hexagonal shoulder made from Ident. No. 001–003: For screwdriving tasks in tight spaces. chrome-vanadium/molybdenum steel

Execution: Advantage: . Continuously hardened . Wiha-Chromtop® for accurate working processes . Matt chromium-plated . So Finish® handle with roll-oﬀ protection Technical data: . Material of the grip handle: 2-component plastic . Ident. No. 001–003: Short round blade and Stubby handle shape . Ident. No. 050–100: Round blade made from chrome-vanadium/molybdenum steel

Ident. No. 050–100 Ident. No. 110–410

Ident. No. 001–003

Tip size PH1 PH2 PH3 PH0 PH1 PH1 PH2 PH2 PH3 PH4 PH2 PH2 PH3 PH4 Blade length (mm) 25 25 25 60 80 200 100 150 150 200 80 100 150 200 Length (mm) 81 81 81 164 191 311 218 268 274 324 186 213 268 318 Ident. No. 001 002 003 050 060 070 080 082 090 100 110 210 310 410 52792... ● ● ● ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 533 Cross-point PH screwdrivers ( ISO 8764 ) For PHILLIPS-RECESS screws

Application: . Ident. No. 800–820: For damp and oily screwing tasks. . Hexagonal blade with hexagonal shoulder made from chrome-vanadium/molybdenum steel Execution: . Solid steel cap . Continuously hardened Ident. No. 690–740 Advantage: . Matt chromium-plated . Wiha-Chromtop® for accurate working processes . MicroFinish® handle with roll-oﬀ protection and non-slip surface texture Technical data: . Black/magenta . Material of the grip handle: 2-component plastic . Ident. No. 690–740: Round blade made from Ident. No. 800–820 chrome-vanadium/molybdenum steel Tip size PH0 PH1 PH1 PH2 PH2 PH3 PH1 PH2 PH3 Blade length (mm) 60 80 200 100 200 150 80 100 150 Length (mm) 165 192 312 220 320 277 187 215 271 Ident. No. 690 700 710 720 730 740 800 810 820 52792... ● ● ● ● ● ● ● ● ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1335 Availability subject to country specific rules and regulations.

1331_EN_2018_KERN[21850866]-r.indd 1335 12/17/2018 3:36:06 PM Screwdrivers \ Slotted and Phillips screwdrivers

Ergonic screwdriver set Hexagonal blade

Execution: Advantage: . Patented elasticated handle structure . Handle adjusts to your hand for optimum force . Hexagonal blade with hexagonal shoulder made transmission and sensitivity from chrome-vanadium/molybdenum steel . Cross hole for hanging up or inserting a lever . Handle top with roll-oﬀ protection . Black-Tip to maintain accuracy and for a longer service life . Hexagonal shoulder for use with a wrench Composition of set Supplied blade widths: 5.5 mm/6.5 mm Tip size PH1 | PH2 | PZ1 | PZ2 Ident. No. 400 52740... ● Prod. Gr. 5JF

Screwdriver sets

Execution: Advantage: . 3-component power grip . 3-component power grip for high force . Ident. No. 504: transmission . Round blades . Ident. No. 504: . Matt chromium-plated . Ergonomic shape for fatigue-free working . With steel impact cap . Steel cap for use as a chisel . Ident. No. 505: . Ident. No. 505: ergonomic shape for fatigue-free . round blades working . brushed chromium-plated Ident. No. 504 Composition of set Supplied blade widths: blade widths supplied: 45 mm/5.5 mm/7 mm 3 mm/4 mm/5.5 mm/6.5 mm Tip size PH1 | PH2 PH1 | PH2 Ident. No. 505 Ident. No. 504 505 52740... ● ● Prod. Gr. 569

Screwdriver sets 6-piece

Execution: . completely hardened and tempered blade with . 3-component Power Grip handle - for optimum optimum elasticity and wear resistance power transmission Advantage: . so quick-turning zone with hard power point . equally suited to small and large hands, right and le handers.

Composition of set blade widths supplied: blade widths supplied: 4.0 mm/5.5 mm/6.5 mm/8 mm 4.0 mm/5.5 mm/6.5 mm/8 mm Ident. No. 010 Tip size PH1 | PH2 PZ1 | PZ2 Ident. No. 010 020 52741... ● ● Prod. Gr. 530

Slotted screwdrivers ( DIN 5264 ) Hexagonal blade and striking cap

Execution: Advantage: . End-to-end tempered hexagonal blade . Impact-resistant blade . Hexagonal shoulder . Black Point tip for longer service life and enhanced . Multi-component Kra form handle with roll-away protection against corrosion protection for sizes 3.5 mm to 10 mm . Size 4.5 mm to 14 mm with steel cap for use as a . Black Point tip chisel . Size 12 and 14 mm/ident. no. 070 and 080 with . Hexagonal shoulder for use with a wrench 1-C Weralit handle

Width of cutting edge (mm) 3.5 4.5 5.5 7 9 10 12 14 Thickness of cutting edge (mm) 0.6 0.8 1 1.2 1.6 1.6 2 2.5 Blade length (mm) 80 90 100 125 150 175 200 250 Length (mm) 161 188 205 230 262 287 317 367 2-component 2-component 2-component 2-component 2-component 2-component 1-component 1-component Material of the grip handle plastic plastic plastic plastic plastic plastic plastic plastic Ident. No. 010 020 030 040 050 060 070 080 52765... ● ● ● ● ● ● ● ● Prod. Gr. 542

Source: Hahn+Kolb Werkzeuge GmbH 1336Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1331_EN_2018_KERN[21850866]-r.indd 1336 12/17/2018 3:36:08 PM Screwdrivers \ Slotted and Phillips screwdrivers

Slotted, Phillips and TX screwdriver set ( DIN 5264 ) Hexagonal blade and striking cap

Execution: . Kra form multi-component handle for optimum . Continuous, tempered and impact-resistant force transmission hexagon blade . Steel cap for use as a chisel . Black Point tip for longer service life and enhanced . Hexagonal shoulder for use with a wrench corrosion protection Delivery: In plastic rack to hang up Supplied blade widths: 3.5 mm/4.5 mm/5.5 Composition of set mm/7 mm Number of pieces in assortment/set 6 Tip size PH1 | PH2 Ident. No. 800 52765... ● Prod. Gr. 542 Cross-point screwdrivers ( DIN 5260 ) PH and PZ drives

Execution: Advantage: . End-to-end tempered hexagonal blade . Impact-resistant blade . Multi-component Kra form handle with roll-away . Black Point tip for longer service life and enhanced protection for sizes PH/PZ 1 to 3 protection against corrosion . Size PH 4 and PZ 4/ident. no. 040 and 140 with . Steel cap for use as a chisel 1-C Weralit handle . Hexagonal shoulder for use with a wrench . Black Point tip

Tip size PH1 PH2 PH3 PH4 PZ1 PZ2 PZ3 PZ4 Blade length (mm) 80 100 150 200 80 100 150 200 Length (mm) 178 205 262 317 178 205 262 317 Material of the grip handle 2-component 2-component 2-component 1-component 2-component 2-component 2-component 1-component plastic plastic plastic plastic plastic plastic plastic plastic Ident. No. 010 020 030 040 110 120 130 140 52767... ● ● ● ● ● ● ● ● Prod. Gr. 542

XXL screwdriver sets Circular blade

Execution: Advantage: . Screwdriver with power grip . Multi-component handle for greater comfort . Ident. No. 010: . Ident. No. 010: . Lasertip tip . Micro-roughened, sharp-edged surface texture . round blades, slotted, cross-head and TX created by laser tip securely holds the screw- . Ident. No. 020: driver in the screw head . Workshop, VDE, screw chisel screwdrivers . Cam-Out eﬀ ect is reduced . round and hexagon blades, slotted, cross-head . Lower contact force required Ident. No. 010 Ident. No. 020 and TX Delivery: In plastic rack to hang up

Composition of set Supplied blade widths: 35 Supplied blade widths: 2.5 mm/4 mm/6.5 mm mm/3.5 mm/5.5 mm/7 mm Number of pieces in assortment/set 14 12 PH1 | PH2 | PH3 | PZ1 | PZ2 PH1 | PH2 | PZ1 | PZ2 | Tip size | PZ3 | TX10 | TX15 | TX20 | TX15 | TX20 | TX25 TX25 | TX30 Ident. No. 010 020 52768... ● ● Prod. Gr. 542

Slotted screwdriver with wooden handle

Execution: Technical data: . Blade made of chrome-vanadium steel . Material of the grip handle: Wood . Chrome-plated . Wooden handle with leather cap . Continuous blade with hexagonal shoulder . Blackened tip

Width of cutting edge (mm) 3.5 4.5 5.5 7 9 10 12 14 Thickness of cutting edge (mm) 0.6 0.8 1.0 1.2 1.4 1.6 2.0 2.5 Blade length (mm) 75 90 100 125 150 175 200 250 Length (mm) 175 190 205 230 270 295 325 380 Ident. No. 510 520 530 540 550 560 570 580 52730... ● ● ● ● ● ● ● ●

Prod. Gr. 590

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1337 Availability subject to country specific rules and regulations.

1337_EN_2018_KERN[21850873]-t.indd 1337 12/17/2018 3:35:57 PM Screwdrivers \ Slotted and Phillips screwdrivers

Slotted and Phillips screwdriver sets Wooden handle

Execution: . Wooden handle with leather cap . Blade made of chrome-vanadium steel . Continuous blade with hexagonal shoulder . Chrome-plated . Blackened tip

Supplied blade widths: 3.5 Supplied blade widths: 4.5 mm/4.5 mm/5.5 mm/7 Composition of set mm/55 mm/7 mm/9 mm mm/9 mm/10 mm/12 mm Ident. No. 800 Number of pieces in assortment/set 6 7 Tip size PH1 | PH2 - Ident. No. 800 810 52730... ● ● Prod. Gr. 590

Phillips screwdriver with wooden handle ( ISO 8764 ) with PH drive

Tip size PH1 PH2 PH3 PH4 Blade length (mm) 80 100 150 200 Length (mm) 180 205 270 330 Ident. No. 540 550 560 570 52782... ● ● ● ● Prod. Gr. 590 Slotted screwdrivers Circular blade

Execution: . High degree of torque transmission . Two-component grip with large so area . Cross hole for hanging up or inserting a lever . Cross hole Technical data: Advantage: . Material of the grip handle: 2-component plastic . Ergonomic, eﬀ ortless work

Width of cutting edge (mm) 2.5 3 3.5 4 5.5 6.5 8 10 12 Thickness of cutting edge (mm) 0.4 0.5 0.6 0.8 1.0 1.2 1.2 1.6 2.0 Blade length (mm) 75 75 100 100 125 150 175 200 250 Length (mm) 135 155 175 185 220 255 290 315 355 Ident. No. 025 030 035 040 055 065 080 100 120 52752... ● ● ● ● ● ● ● ● ● Prod. Gr. 5LA

Slotted and Phillips screwdriver sets Circular blade

Execution: Advantage: . Two-component grip with large so area . Ergonomic, eﬀ ortless work . Cross hole . High degree of torque transmission . Cross hole for hanging up or inserting a lever

Supplied blade widths: Supplied blade widths: Supplied blade widths: 2.5 mm/3 mm/3.5 Composition of set 4 mm/5.5 mm/6.5 3.5 mm/4 mm/5.5 mm/4 mm/5.5 Ident. No. 200 mm mm/6.5 mm/8 mm mm/6.5 mm/8 mm/10 mm Number of pieces in assortment/set 5 5 8 Tip size PH1 | PH2 - - Ident. No. 200 230 250 52752... ● ● ● Prod. Gr. 5LA

Source: Hahn+Kolb Werkzeuge GmbH 1338Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1337_EN_2018_KERN[21850873]-t.indd 1338 12/17/2018 3:36:00 PM Screwdrivers \ Slotted and Phillips screwdrivers

Phillips screwdrivers ( ISO 8764 ) with PH and PZ drives

Execution: . High degree of torque transmission . Two-component grip with large so area . Cross hole for hanging up or inserting a lever . Cross hole Technical data: Ident. No. 005–030 Advantage: . Material of the grip handle: 2-component plastic . Ergonomic, eﬀ ortless work

Ident. No. 105–130

Tip size PH0 PH1 PH2 PH3 PZ0 PZ1 PZ2 PZ3 Blade length (mm) 60 80 100 150 60 80 100 150 Length (mm) 135 175 205 265 135 175 205 265 Ident. No. 005 010 020 030 105 110 120 130 52788... ● ● ● ● ● ● ● ● Prod. Gr. 5LA

Voltage tester screwdriver For 150-250 V

Application: . Ergonomically shaped, transparent handle with Testing equipment for determining alternating volt- light tubes ages according to VDE 0680 Advantage: Execution: . Ergonomic handle for comfortable handling . Plastic-coated blade made from chrome-vanadium . With practical clip steel Width of cutting edge (mm) 3 Thickness of cutting edge (mm) 0.8 Blade length (mm) 70 Length (mm) 143 Material of the grip handle 1-component plastic Ident. No. 100 52721... ● Prod. Gr. 590 Voltage tester screwdriver For 150-250 V

Application: . Light tubes (cannot be replaced) Testing equipment for determining alternating volt- . Clip ages according to DIN VDE 0680-6 . Ident. No. 020: Transparent handle Ident. No. 020 Ident. No. 100 Execution: . Ident. No. 100: Black handle . Vanadium special steel blade Advantage: . Cellulose acetate handle . Instantly to hand thanks to the clip Width of cutting edge (mm) 3 3 Thickness of cutting edge (mm) 0.8 0.8 Blade length (mm) 60 70 Length (mm) 143 165 Material of the grip handle 1-component plastic 1-component plastic Ident. No. 020 100 52722... ● ● Prod. Gr. 533 Voltage tester with cable and clamp

Application: . Unscrewable tester tip, with needle tip Equipment for determining voltages . Light tubes (cannot be replaced) . 6 to 24 V voltage measuring range Execution: . Robust brass housing Advantage: . With 870-mm connection cable and crocodile clip . Insulated cables can also be tested using the needle tip Length (mm) 150 Material of the grip handle Brass Ident. No. 010 52723... ● Prod. Gr. 579

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1339 Availability subject to country specific rules and regulations.

1339_EN_2018_KERN[21850876]-s.indd 1339 12/17/2018 3:35:54 PM Screwdrivers \ Slotted and Phillips screwdrivers

Voltage tester and magnetic ﬁ eld tester

Execution: . frequency range 50/60 Hz . Ident. No. 020: . Ident. No. 030–040: visual and acoustic display . Type VT Check CTB - 5–48 V . Ident. No. 040: . LED display 5, 12, 24, 48 V . type VT M, contactless tester . Polarity (+/-) yes, 1-m cable . 2 voltage ranges 12–50 V or 50–1000 V . Ident. No. 030: . magnetic ﬁ eld detection > 2.5 nT . type VT CL, contactless voltage testing . voltage range 90–1000 V AV Delivery: Ident. No. 030–040: includes AAA batteries

Ident. No. 020 Ident. No. 030 Ident. No. 040

Length (mm) 158 155 156 Ident. No. 020 030 040 52723... ● ● ● Prod. Gr. 543 PLUS multi-stripper

Execution: . Cable cutters up to 9 mm . Screwdriver with two reversible bits . Two-component handle . Phase and voltage tester (110-250 V) Advantage: . Cable stripper for 8-13 mm circular cables and . Flexible applications in a single tool coax cables . Ergonomic handle for comfortable handling Length (mm) 199 Ident. No. 010 52724... ● Prod. Gr. 5LA VDE slotted screwdrivers ( DIN 7437 ) with slim blade

Application: . Multi-component handle provides for optimum For working on live components power transmission . Screw symbols on the handle cap Execution: . Roll-oﬀ protection integrated in the handle . Protective insulation (to DIN EN 60900) sprayed directly onto the blade Technical data: . Slim design: Insulating layer in the front part ﬂ ush . Material of the grip handle: 3-component plastic with the output Width of cutting edge (mm) 3.5 4.0 5.5 6.5 Thickness of cutting edge (mm) 0.6 0.8 1.0 1.2 Blade length (mm) 100 100 125 125 Length (mm) 197 207 244 269 Ident. No. 335 340 355 365 52725... ● ● ● ● Prod. Gr. 590 VDE Phillips screwdrivers ( DIN 7438 ) with slim blade/PH, PZ and PZS

Application: . Multi-component handle provides for optimum power transmission For working on live components . Screw symbols on the handle cap . Roll-oﬀ protection integrated in the handle Execution: . Protective insulation (to DIN EN 60900) sprayed directly onto the blade Technical data: . Slim design: Insulating layer in the front part ﬂ ush with the output . Material of the grip handle: 3-component plastic Tip size PH1 PH2 PZ1 PZ2 PZ1 + slot PZ2 + slot Blade length (mm) 80 100 80 100 80 100 Length (mm) 187 219 187 219 187 219 Ident. No. 401 402 411 412 421 422 52725... ● ● ● ● ● ● Prod. Gr. 590

Source: Hahn+Kolb Werkzeuge GmbH 1340Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1339_EN_2018_KERN[21850876]-s.indd 1340 12/17/2018 3:36:00 PM Screwdrivers \ Slotted and Phillips screwdrivers

VDE screwdriver, TX with slim blade

Application: . multi-component handle provides optimum power for working on live components transmission . screw symbols on the grip cap Execution: . roll-away protection integrated in the handle . protective insulation as per DIN EN 60900 sprayed directly onto the blade Technical data: . slim design: insulating layer in the front part is . Material of the grip handle: 3-component plastic ﬂ ush with the output

Tip size TX15 TX20 TX25 Blade length (mm) 100 125 125 Length (mm) 207 244 244 Ident. No. 515 520 525 52725... ● ● ● Prod. Gr. 590

VDE screwdriver set ( DIN 7437 ) with slim blade

Application: . Slim design: Insulating layer in the front part ﬂ ush For working on live components with the output . Multi-component handle provides for optimum Execution: power transmission . Protective insulation (to DIN EN 60900) sprayed . Screw symbols on the handle cap directly onto the blade . Roll-oﬀ protection integrated in the handle

Composition of set Bade widths supplied: Blade widths supplied: 3.5 mm/4 mm/5.5 mm/6.5 mm 3.5 mm/4 mm/5.5 mm/6.5 mm Number of pieces in assortment/set 6 6 Tip size PH1 | PH2 PZ1 | PZ2 Ident. No. 600 610 52725... ● ● Prod. Gr. 590 VDE slotted screwdrivers ( DIN 7437 )

Application: . Individually tested For working on live components. Advantage: Execution: . Ergonomic handle for comfortable handling Ident. No. 066 . Protective insulation according to DIN EN 60900 . High degree of torque transmission . Chrome-vanadium/molybdenum steel blade . Hardened and burnished Technical data: . Material of the grip handle: 3-component plastic . Blade insulation sprayed directly onto the blade . 3-component power grip, red/yellow Width of cutting edge (mm) 2.5 3 3.5 4 5.5 6.5 8 10 Thickness of cutting edge (mm) 0.4 0.5 0.6 0.8 1 1.2 1.2 1.6 Blade length (mm) 75 100 100 100 125 150 175 200 Length (mm) 161 186 197 207 244 269 294 319 Ident. No. 026 031 036 041 056 066 081 101 52726... ● ● ● ● ● ● ● ● Prod. Gr. 590 VDE slotted and Phillips screwdriver sets ( DIN 7437 )

Application: . Blade insulation sprayed directly onto the blade For working on live components. . 3-component power grip, red/yellow . Individually tested Execution: . Protective insulation according to DIN EN 60900 Advantage: . Chrome-vanadium/molybdenum steel blade . Ergonomic handle for comfortable handling . Hardened and burnished . High degree of torque transmission

Supplied blade widths: Supplied blade widths: Supplied blade widths: Composition of set 2.5 mm/3.5 mm/4 2.5 mm/3 mm/4 2.5 mm/4 mm/5.5 Ident. No. 201 mm/5.5 mm mm/5.5 mm/65 mm mm/6.5 mm/8 mm Number of pieces in assortment/set 6 7 5 Tip size PH1 | PH2 PH1 | PH2 - Ident. No. 201 202 203 52726... ● ● ● Prod. Gr. 590

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1341 Availability subject to country specific rules and regulations.

1339_EN_2018_KERN[21850876]-s.indd 1341 12/17/2018 3:36:02 PM Screwdrivers \ Slotted and Phillips screwdrivers

VDE Phillips screwdrivers ( DIN 7438 ) For PH and PZ

Application: Advantage: For working on live components. . Ergonomic handle for comfortable handling . High degree of torque transmission Execution: . Protective insulation according to DIN EN 60900 Technical data: Ident. No. 302 . Chrome-vanadium/molybdenum steel blade . Material of the grip handle: 3-component plastic . Hardened and burnished . Blade insulation sprayed directly onto the blade . 3-component power grip, red/yellow . Individually tested

Tip size PH0 PH1 PH2 PH3 PZ0 PZ1 PZ2 PZ3 Blade length (mm) 60 80 100 150 60 80 100 150 Length (mm) 146 187 219 269 146 187 219 269 Ident. No. 300 301 302 303 400 401 402 403 52786... ● ● ● ● ● ● ● ● Prod. Gr. 590 VDE Phillips screwdriver set ( DIN 7438 )

Application: . Blade insulation sprayed directly onto the blade For working on live components. . 3-component power grip, red/yellow . Individually tested Execution: . Protective insulation according to DIN EN 60900 Advantage: . Chrome-vanadium/molybdenum steel blade . Ergonomic handle for comfortable handling Ident. No. 310 . Hardened and burnished . High degree of torque transmission

Tip size PH1 | PH2 | PH3 PZ1 | PZ2 | PZ3 Ident. No. 310 410 52786... ● ● Prod. Gr. 590 VDE slotted screwdrivers ( DIN 7437 )

Application: . So Finish® handle with roll-oﬀ protection For working on live components. Advantage: Execution: . Multi-component handle for greater comfort . Protective insulation according to DIN EN 60900 . High degree of torque transmission . Chrome-vanadium/molybdenum steel blade . Hardened and burnished Technical data: . Material of the grip handle: 2-component plastic . Polyamide blade insulation sprayed directly onto the blade Width of cutting edge (mm) 2 2.5 3 3.5 4 4.5 4.5 5.5 5.5 6 6.5 8 8 10 Thickness of cutting edge (mm) 0.4 0.4 0.5 0.6 0.8 1 1 1 1 1.2 1.2 1.2 1.6 1.6 Blade length (mm) 60 75 100 100 100 125 175 125 175 150 150 175 175 200 Length (mm) 164 179 204 204 211 236 286 243 293 268 268 299 299 321 Ident. No. 010 020 030 040 050 060 070 080 090 100 110 120 130 140 52728... ● ● ● ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 533 VDE screwdriver set ( DIN 7437 )

Application: . Polyamide blade insulation sprayed directly onto For working on live components. the blade . So Finish® handle with roll-oﬀ protection Execution: . Protective insulation according to DIN EN 60900 Advantage: . Chrome-vanadium/molybdenum steel blade . Multi-component handle for greater comfort . Hardened and burnished . High degree of torque transmission Supplied blade widths: 3 mm/4 mm/55 Composition of set mm/6.5 mm Number of pieces in assortment/set 6 Tip size PH1 | PH2 Ident. No. 210 52728... ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH 1342Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1342_EN_2018_KERN[21850880]-y.indd 1342 12/17/2018 3:35:54 PM Screwdrivers \ Slotted and Phillips screwdrivers

VDE screwdriver with bit holder set, So Finish electric slimVario Stubby, 4-piece

Execution: . slim bits for easy and protected access to tight . compact handle – maximum power spaces . tested in line with IEC 60900:2012 Length (mm) 75 Tip size PH2 | PZ2 + slot 2-component Material of the grip handle plastic Ident. No. 150 52729... ● Prod. Gr. 533 SlimFix VDE slotted screwdrivers For slotted screws

Application: . Individually tested For working on live components. . So Finish® handle with roll-oﬀ protection Execution: Advantage: . Insulation (to DIN EN 60900) sprayed directly onto . Slim version for deep-set screws the blade . Multi-component handle for greater comfort . Slim version: Insulation integrated in the bit in the front section Technical data: . Chrome-vanadium/molybdenum steel blade . Material of the grip handle: 2-component plastic . Hardened and burnished Width of cutting edge (mm) 3.5 4 5.5 6.5 Thickness of cutting edge (mm) 0.6 0.8 1 1.2 Blade length (mm) 100 100 125 125 Length (mm) 204 211 243 268 Ident. No. 035 040 055 065 52792... ● ● ● ● Prod. Gr. 533 SlimFix VDE Phillips screwdrivers PH and PZ drives

Application: . Individually tested For working on live components. . So Finish® handle with roll-oﬀ protection Execution: Advantage: . Insulation (to DIN EN 60900) sprayed directly onto . Slim version for deep-set screws the blade . Multi-component handle for greater comfort . Slim version: Insulation integrated in the bit in the front section Technical data: . Chrome-vanadium/molybdenum steel blade . Material of the grip handle: 2-component plastic . Hardened and burnished Tip size PH1 PH2 PZ1 PZ2 Blade length (mm) 80 100 80 100 Length (mm) 191 218 219 218 Ident. No. 101 102 201 202 52792... ● ● ● ● Prod. Gr. 533 SlimFix VDE screwdriver sets

Application: . Ident. No. 350: For working on live components. . insulation (to DIN EN 60900) sprayed directly onto the blade Execution: . slim version: insulation integrated in the bit in the . So Finish® handle with roll-oﬀ protection front section . Ident. No. 300: . individually tested . Insulation (to DIN EN 60900) sprayed directly Advantage: onto the blade Ident. No. 300 . Slim version: Insulation integrated in the bit in . Ident. No. 300: Slim version for deep-set screws the front section . Ident. No. 350: slim version for deep-set screws . Individually tested Supplied blade widths: 3.5 blade widths supplied: 3.5 Composition of set mm/4 mm/5.5 mm/6.5 mm mm/4 mm/5.5 mm/6.5 mm Number of pieces in assortment/set 6 12 PH1 | PH2 | PZ1 | PZ2 | PZ2 Tip size PH1 | PH2 + slot | TX15 | TX20 | TX25 Ident. No. 300 350 52792... ● ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1343 Availability subject to country specific rules and regulations.

1342_EN_2018_KERN[21850880]-y.indd 1343 12/17/2018 3:35:56 PM Screwdrivers \ Slotted and Phillips screwdrivers

SlimVario VDE screwdriver sets Interchangeable blade system

Application: Advantage: For working around live parts up to 1000 V, particu- . So Finish electric multi-component handle with larly for mobile use. roll-oﬀ protection . Protective insulation sprayed directly onto the bit, Execution: completely integrated in the bit in the front section . High-quality chrome-vanadium steel bits, continu- . Easy to reach deep-set screws ously hardened and burnished . Individually tested protective insulation 1000 V AC, Delivery: Ident. No. 400 Ident. No. 402 VDE and GS certiﬁ ed In high-quality and durable case . ref. no. 400 with voltage tester screwdrivers . ref. no. 401 and 402 with additional Stubby bit holder handle

Supplied blade widths: 2.5 mm/3 blade widths supplied: blade widths supplied: Composition of set mm/3.5 mm/4 mm/55 mm 2.5 mm/3.5 mm/5.5 mm 2.5 mm/3.5 mm/5.5 mm Number of pieces in assortment/set 16 9 18 PH1 | PH2 | PZ1 | PZ2 | PZ1 + PH1 | PH2 | PZ1 | PZ2 | PZ2 + slot | PZ2 + slot | TX9 | TX10 | Tip size PH1 | PH2 | PZ1 | PZ2 slot | TX10 | TX15 | TX20 | TX25 TX15 | TX20 | 3 mm | 4 mm | 5 mm Ident. No. 400 401 402 52792... ● ● ● Prod. Gr. 533

VDE screwdriver set 7-piece

Execution: . VDE insulated to 1000 V in line with EN 60900 . 3-component Power Grip handle - for optimum (fully insulated blade) power transmission Advantage: . so quick-turning zone with hard power point . equally suited to small and large hands, right and . completely hardened and tempered blade with le handers. optimum elasticity and wear resistance

blade widths supplied: Composition of set 2.5 mm/4.0 mm/5.5 mm/6.5 mm Tip size PH0 | PH1 | PH2 Ident. No. 010 52726... ● Prod. Gr. 530

VDE Lasertip® slotted screwdrivers Slotted

Application: Advantage: For working on live components. . Multi-component handle for optimum handling . High degree of torque transmission Execution: . Protective insulation according to DIN EN 60900 Technical data: . Ergonomic power grip . Material of the grip handle: 2-component plastic . Lasertip blade . Individually tested Width of cutting edge (mm) 2.5 3 3.5 4 5.5 6.5 8 10 Thickness of cutting edge (mm) 0.5 0.5 0.6 0.8 1 1.2 1.6 1.6 Blade length (mm) 80 100 100 100 125 150 200 200 Length (mm) 156 181 181 198 223 255 312 312 Ident. No. 004 005 006 008 010 012 016 017 52727... ● ● ● ● ● ● ● ● Prod. Gr. 542

VDE Lasertip® Phillips screwdriver

Application: Advantage: For working on live components. . Multi-component handle for optimum handling . High degree of torque transmission Execution: . Protective insulation according to DIN EN 60900 Technical data: . Ergonomic power grip . Material of the grip handle: 2-component plastic . Lasertip blade . Individually tested Tip size PH0 PH1 PH2 PH3 PZ0 PZ1 PZ2 PZ3 Blade length (mm) 80 80 100 150 80 80 100 150 Length (mm) 161 178 205 262 161 178 205 262 Ident. No. 100 101 102 103 200 201 202 203 52727... ● ● ● ● ● ● ● ● Prod. Gr. 542

Source: Hahn+Kolb Werkzeuge GmbH 1344Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1344_EN_2018_KERN[21850883]-u.indd 1344 12/17/2018 3:35:56 PM Screwdrivers \ Slotted and Phillips screwdrivers

VDE Lasertip® screwdriver set

Application: . High degree of torque transmission For working on live components. . Micro-roughened, sharp-edged surface texture created by laser tip securely holds the screwdriver Execution: in the screw head . Protective insulation according to DIN EN 60900 . Cam-Out eﬀ ect is reduced . Ergonomic power grip . Lower contact force required . Lasertip blade from a blade width of 3.5 mm Ident. No. 430 . Individually tested Technical data: . Composition of set: Supplied blade widths: 2.5 Advantage: mm/3 mm/3.5 mm/4 mm/55 mm . Multi-component handle for greater comfort Ident. No. 410–420 Number of pieces in assortment/set 7 7 14 PH1 | PH2 | PZ1 | PZ2 | PZ1 + slot | Tip size PH1 | PH2 PZ1 | PZ2 PZ2 + slot | TX10 | TX15 | TX20 Ident. No. 410 420 430 52727... ● ● ● Prod. Gr. 542

VDE interchangeable blade sets

Application: . Ident. No. 610: For working on live parts, particularly suitable for . 12 VDE interchangeable blades, length 154 mm mobile use. . 4 control cabinet keys, length 89 mm

Execution: Advantage: . 1 Kra form VDE hand-held holder for Wera VDE . Two-component power grip for ergonomic positive interchangeable blades lock and optimum force transmission Ident. No. 610 . 1 voltage tester . Always ready to hand — stored and transported in Ident. No. 600 . Handle with roll-oﬀ protection robust belt pouch . Ident. No. 600: 14 VDE interchangeable blades, Delivery: length 154 mm In belt pouch Supplied blade widths: 2.5 Supplied blade widths: 2.5 Composition of set mm/3 mm/3.5 mm/4 mm/3 mm/3.5 mm/4 mm/55 mm mm/55 mm PH1 | PH2 | PZ1 | PZ2 | PZ1 PH1 | PH2 | PZ1 | PZ2 | PZ1 Tip size + slot | PZ2 + slot | TX10 | + slot | PZ2 + slot TX15 | TX20 | TX25 Ident. No. 600 610 52727... ● ● Prod. Gr. 542

Esmart VDE screwdriver

Application: . Certiﬁ ed ‘GS’ safety For working on live components. . Individually tested Execution: Advantage: . Protective insulation according to DIN EN 60900 . Blades held securely in grip thanks to automatic . Safe up to 1000-V alternating voltage lock in the handle . Two-component handle . Rotary cap and so shell for use as precision tool . Clip-on rotary cap Delivery: . So shell area In plastic case Supplied blade widths: 2.5 mm/3 mm/3.5 Composition of set mm/4 mm/5.5 mm/6.5 mm Number of pieces in assortment/set 14 Tip size PH1 | PH2 | TX10 | TX15 | TX20 Ident. No. 300 52724... ● Prod. Gr. 5JF

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1345 Availability subject to country specific rules and regulations.

1344_EN_2018_KERN[21850883]-u.indd 1345 12/17/2018 3:36:00 PM Screwdrivers \ Slotted and Phillips screwdrivers

VDE slotted screwdrivers ( DIN 7437 )

Application: Advantage: For working on live components. . Ergonomic handle for comfortable handling . Better resistance to corrosion Execution: . Handle and insulation in impact-resistant plastic . Protective insulation according to DIN EN 60900 . High-alloy special steel blade Technical data: . Hardened and burnished . Material of the grip handle: 1-component plastic . Individually tested

Width of cutting edge (mm) 2.5 3 3.5 4 5.5 6.5 8 10 Thickness of cutting edge (mm) 0.4 0.5 0.6 0.8 1 1.2 1.2 1.6 Blade length (mm) 75 100 100 100 125 150 175 200 Length (mm) 155 180 180 190 225 250 285 310 Ident. No. 530 540 550 560 580 590 600 610 52728... ● ● ● ● ● ● ● ● Prod. Gr. 5LA VDE slotted screwdriver set ( DIN 7437 )

Application: Advantage: For working on live components. . Ergonomic handle for comfortable handling . Handle and insulation in impact-resistant plastic Execution: . Protective insulation according to DIN EN 60900 Delivery: . High-alloy special steel blade In cardboard packaging . Hardened and burnished . Certiﬁ ed ‘GS’ safety . Individually tested Supplied blade widths: 2.5 mm/3 mm/4 Composition of set mm/5.5 mm/65 mm Number of pieces in assortment/set 7 Tip size PH1 | PH2 Ident. No. 800 52728... ● Prod. Gr. 5LA VDE Phillips PH screwdriver ( DIN 7438 )

Application: Advantage: For working on live components. . Ergonomic handle for comfortable handling . Handle and insulation in impact-resistant plastic Execution: . Protective insulation according to DIN EN 60900 Technical data: . High-alloy special steel blade . Material of the grip handle: 1-component plastic . Hardened and burnished . Individually tested Tip size PH0 PH1 PH2 PH3 Blade length (mm) 60 80 100 150 Length (mm) 140 170 200 260 Ident. No. 530 540 550 560 52784... ● ● ● ● Prod. Gr. 5LA Philips head PH (Philips-Recess) and PZ (Pozidriv) bits. T-shape, Y-shape and TY-shape

Execution: . Y-shape especially suitable for screws in Y-shape . Patented WIHA bit technology with optimized (countersunk head). torsion zone . TY-shape suitable for all types of screws No. 52970 . High durability and very high quality standard. Delivery: . Colour marking makes the bit noticeable and thus Pack of 5 easy to ﬁ nd. . The ﬂ uorescent coating makes the bit visible even Technical data: in the dark when using a UV lamp. . Drive: 1/4 inch . T-shape especially suitable for screws in T-shape . Blade length: 29 mm (cylinder head). No. 52971

Source: Hahn+Kolb Werkzeuge GmbH 1346Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1346_EN_2018_KERN[21850887]-u.indd 1346 12/17/2018 3:36:01 PM Screwdrivers \ Bit range

TY-shape TY-shape Tip size 52970... 52971... Ident. No. Ident. No. PH1 021 ● - - PH2 022 ● - - PH3 023 ● - - PZ1 - - 021 ● PZ2 - - 022 ● PZ3 - - 023 ● Prod. Gr. 571 Philips head PH (Philips-Recess) and PZ (Pozidriv) bits. T-shape, Y-shape and TY-shape

Execution: . Y-shape especially suitable for screws in Y-shape No. 52974 . Patented WIHA bit technology with optimized (countersunk head). torsion zone . TY-shape suitable for all types of screws . High durability and very high quality standard. Delivery: . Colour marking makes the bit noticeable and thus Pack of 5 easy to ﬁ nd. No. 52975 . The ﬂ uorescent coating makes the bit visible even Technical data: in the dark when using a UV lamp. . Drive: 1/4 inch . T-shape especially suitable for screws in T-shape . Blade length: 49 mm (cylinder head). TY-shape TY-shape Tip size 52974... 52975... Ident. No. Ident. No. PH1 021 ● - - PH2 022 ● - - PH3 023 ● - - PZ1 - - 021 ● PZ2 - - 022 ● PZ3 - - 023 ● Prod. Gr. 571 TX bit T-shape, Y-shape and TY-shape

Execution: . Y-shape especially suitable for screws in Y-shape . Patented WIHA bit technology with optimized (countersunk head) torsion zone . TY-shape suitable for all types of screws . High durability and very high quality standard. Delivery: . Colour marking makes the bit noticeable and thus Pack of 5 easy to ﬁ nd. . The ﬂ uorescent coating makes the bit visible even Technical data: in the dark when using a UV lamp. . Drive: 1/4 inch . T-shape especially suitable for screws in T-shape . Blade length: 29 mm (cylinder head). TY-shape Tip size 52973... Ident. No. TX10 210 ● TX15 215 ● TX20 220 ● TX25 225 ● TX27 227 ● TX30 230 ● TX40 240 ● Prod. Gr. 571 TX bit T-shape, Y-shape and TY-shape

Execution: . Y-shape especially suitable for screws in Y-shape . Patented WIHA bit technology with optimized (countersunk head) torsion zone . TY-shape suitable for all types of screws . High durability and very high quality standard. Delivery: . Colour marking makes the bit noticeable and thus Pack of 5 easy to ﬁ nd. . The ﬂ uorescent coating makes the bit visible even Technical data: in the dark when using a UV lamp. . Drive: 1/4 inch . T-shape especially suitable for screws in T-shape . Blade length: 49 mm (cylinder head). TY-shape Tip size 52977... Ident. No. TX10 210 ● TX15 215 ● TX20 220 ● TX25 225 ● TX27 227 ● TX30 230 ● TX40 240 ● Prod. Gr. 571 Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1347 Availability subject to country specific rules and regulations.

1346_EN_2018_KERN[21850887]-u.indd 1347 12/17/2018 3:36:06 PM Screwdrivers \ Bit range

Internal hexagon bit T-shape and TY-shape

Execution: . T-shape especially suitable for screws in T-shape . Patented WIHA bit technology with optimized (cylinder head). torsion zone . TY-shape suitable for all types of screws . High durability and very high quality standard. Delivery: . Colour marking makes the bit noticeable and thus Pack of 5 easy to ﬁ nd. . The ﬂ uorescent coating makes the bit visible even Technical data: in the dark when using a UV lamp. . Drive: 1/4 inch . Blade length: 29 mm

Width across ﬂ ats 3 mm 4 mm 5 mm 6 mm TY-shape Ident. No. 023 024 025 026 52972... ● ● ● ● Prod. Gr. 571

Internal hexagon bit T-shape and TY-shape

Width across ﬂ ats 3 mm 4 mm 5 mm 6 mm TY-shape Ident. No. 023 024 025 026 52976... ● ● ● ● Prod. Gr. 571

Bit set BitBuddy TY-bit 29 mm 8-piece, with magnetic bit holder

Execution: . The fl uorescent coating makes the bit visible even . Patented bit technology for optimized torsion zone in the dark when using a UV lamp. . TY-shape for fi ttings in all materials . The highest quality standard ensures long service Technical data: . Drive: 1/4 inch life . Blade length: 29 mm . Colour marking makes the bit noticeable and thus . Number of pieces in assortment/set: 8 PCS easy to fi nd.

Ident. No. 010

Ident. No. 050 TY-shape Tip size 52981... Ident. No. PZ1 | PZ2 | PZ3 010 ● HEX 3 mm | HEX 4 mm | HEX 5 mm | HEX 6 mm 020 ● TX10 | TX15 | TX20 | TX25 | TX30 | TX40 030 ● PH2 | PZ1 | PZ2 | PZ3 | TX15 | TX20 | TX25 040 ● PH2 | PZ1 | PZ2 | TX10 | TX15 | TX20 | TX25 050 ● PZ2 | PZ3 | TX15 | TX20 | TX25 | TX30 | TX40 060 ● Prod. Gr. 571

Source: Hahn+Kolb Werkzeuge GmbH 1348Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1346_EN_2018_KERN[21850887]-u.indd 1348 12/17/2018 3:36:09 PM Screwdrivers \ Bit range

Bit set BitBuddy TY-bit 49 mm 7 pieces

Execution: Technical data: . Patented bit technology for optimized torsion zone . Drive: 1/4 inch . TY-shape for fi ttings in all materials . Blade length: 49 mm . The highest quality standard ensures long service life . Colour marking makes the bit noticeable and thus easy to fi nd. . The fl uorescent coating makes the bit visible even in the dark when using a UV lamp. Ident. No. 010

Ident. No. 050 TY-shape Tip size Number of pieces in assortment/set (PCS) 52982... Ident. No. PZ1 | PZ2 | PZ3 - 010 ● HEX 3 mm | HEX 4 mm | HEX 5 mm | HEX 6 mm 7 020 ● TX10 | TX15 | TX20 | TX25 | TX30 | TX40 7 030 ● PH2 | PZ1 | PZ2 | PZ3 | TX15 | TX20 | TX25 7 040 ● PH2 | PZ1 | PZ2 | TX10 | TX15 | TX20 | TX25 7 050 ● PZ2 | PZ3 | TX15 | TX20 | TX25 | TX30 | TX40 7 060 ● Prod. Gr. 571

Hexagon bits For hexagonal socket screws

Execution: Technical data: . 1/4”-external hexagon drive, type C 6.3 according . Drive: 1/4 inch to DIN 3126/ISO 1173 . Blade length: 25 mm . Chrome-vanadium steel . Surface: Uncoated . Continuously hardened

Width across ﬂ ats 1.5 mm 2 mm 2.5 mm 3 mm 5 mm 6 mm 8 mm 10 mm Ident. No. 015 020 025 030 050 060 080 100 52847... ● ● ● ● ● ● ● ● Prod. Gr. 571

Hexagon bits For hexagon socket bolts with direct screwdriver connection

Execution: Technical data: . 1/4”-external hexagon drive, type E 6.3 according . Drive: 1/4 inch to DIN 3126/ISO 1173 . Surface: Uncoated . Tough material Width across ﬂ ats 2.5 mm 3 mm 4 mm 5 mm 6 mm 8 mm 2.5 mm 3 mm 4 mm 5 mm 6 mm 8 mm 10 mm Blade length (mm) 50 50 50 50 50 50 70 70 70 70 70 70 70 Ident. No. 702 703 704 705 706 708 802 803 804 805 806 808 810 52847... ● ● ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 540

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1349 Availability subject to country specific rules and regulations.

1346_EN_2018_KERN[21850887]-u.indd 1349 12/17/2018 3:36:11 PM Screwdrivers \ Bit range

PHILLIPS-RECESS bits

Execution: . 1/4”-external hexagon drive, type C 6.3 according to DIN 3126/ISO 1173 Technical data: . Drive: 1/4 inch . Chrome-vanadium steel . Surface: Uncoated . Continuously hardened Tip size PH0 PH1 PH2 PH3 PH4 Blade length (mm) 25 25 25 25 32 Standard Ident. No. 020 021 022 023 034 52848... ● ● ● ● ● Prod. Gr. 571

PHILLIPS-RECESS bits

Execution: Technical data: . 1/4”-external hexagon drive type E 6.3 according . Drive: 1/4 inch to DIN 3126/ISO 1173 . Surface: Uncoated Standard design

Tip size PH1 PH2 PH3 PH1 PH2 PH3 Blade length (mm) 70 70 70 90 90 90 Standard Ident. No. 071 072 073 091 092 093 52849... ● ● ● ● ● ● Prod. Gr. 571

TX bit

Execution: . Ident. No. 306–540: 1/4”-external hexagon drive . Chrome-vanadium steel type E 6.3 according to DIN 3126/ISO 1173 . Continuously hardened Technical data: . Ident. No. 005–050: 1/4”-external hexagon drive, . Drive: 1/4 inch 6.3 according to DIN 3126/ISO 1173 type C . Surface: Uncoated Ident. No. 005–050

Ident. No. 306–540

Tip size TX5 TX6 TX7 TX8 TX9 TX10 TX15 TX20 Blade length (mm) 25 25 25 25 25 25 25 25 Ident. No. 005 006 007 008 009 010 015 020 52852... ● ● ● ● ● ● ● ● Tip size TX25 TX27 TX30 TX40 TX45 TX50 TX6 TX8 Blade length (mm) 25 25 25 25 35 35 70 70 Ident. No. 025 027 030 040 045 050 306 308 52852... ● ● ● ● ● ● ● ● Tip size TX10 TX15 TX20 TX25 TX27 TX30 TX40 TX10 Blade length (mm) 70 70 70 70 70 70 70 150 Ident. No. 310 315 320 325 327 330 340 510 52852... ● ● ● ● ● ● ● ● Tip size TX15 TX20 TX25 TX30 TX40 Blade length (mm) 150 150 150 150 150 Ident. No. 515 520 525 530 540 52852... ● ● ● ● ● Prod. Gr. 571

Source: Hahn+Kolb Werkzeuge GmbH 1350Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1350_EN_2018_KERN[21850892]-w.indd 1350 12/17/2018 3:35:56 PM Screwdrivers \ Bit range

Bit holder 1/4 inch drive and 1/4 inch bit holder

Execution: . Ident. No. 310: With snap ring and magnet . Ident. No. 030: . 1/4” drive, hexagon, type E 6.3 . Ideally suited for working in cramped conditions Advantage: . . Robust aluminium actuation sleeve Ident. No. 025–030: . . Automatic bit lock Ident. No. 025: . Bit is held securely and with no play . Bit removed using the eject function Technical data: . Robust, hardened steel actuation sleeve . Bit holder: 1/4 inch hexagon . Ident. No. 025–130: With permanent magnet

Ident. No. 030 Ident. No. 120 Ident. No. 130 Ident. No. 310 Ident. No. 025

Length (mm) 60 66 59 74 57 Ident. No. 025 030 120 130 310 52853... ● ● ● ● ● Prod. Gr. 571

Bit holder 1/4 inch drive and 1/4 inch bit holder

Execution: . Powerful permanent magnet . Ident. No. 001–003: . Universal holder Technical data: . Stainless steel sleeve . Bit holder: 1/4 inch hexagon . Snap ring

Ident. No. 003 Ident. No. 001 Ident. No. 002 Ident. No. 240 Ident. No. 220, 230 Ident. No. 225

Ident. No. 245

Length (mm) 50 75 100 Universal holder with snap Ident. No. 001 002 003 52856... ring and magnet ● ● ● Rapidaptor holder with quick- Ident. No. 220 52856... change chuck ● - - Rapidaptor holder with ring 225 52856... magnet with powerful perma- Ident. No. - ● - nent magnet Rapidaptor holder with quick- Ident. No. 230 - - 52856... change chuck and magnet ● Rapidaptor BiTorsion holder 240 52856... with quick-change chuck and Ident. No. - ● - powerful permanent magnet Impaktor bit holder TriTor- 245 52856... sion with ring magnet and Ident. No. - ● - snap ring Prod. Gr. 542

Bit box 32 pieces, format C 6.3

Execution: Advantage: . High-strength plastic box with opening mechanism . Torsion zone for reduced risk of the bits breaking . Cross-head bits with tough torsion zone under high stress . Two-component handle with bit holder mount . Resistant to wear . Bit holder for C and E 6.3 bits . Special play-free clamping for optimum hold Drive 1/4 inch 1/4 inch Ident. No. 010 Supplied slot lengths: 4.5 Ident. No. 020 Composition of set mm/5.5 mm/6.5 mm - Sockets with socket hexagon-head tip provided 4 mm | 5 mm | 6 mm - Blade length (mm) 25 25 PH1 | PH2 | PH3 | PZ1 | PZ2 PH1 | PH2 | PH3 | PZ1 | PZ2 Tip size | PZ3 | TX10 | TX15 | TX20 | | PZ3 | TX10 | TX15 | TX20 | TX25 | TX30 | TX40 TX25 | TX30 | TX40 Ident. No. 010 020 52841... ● ● Prod. Gr. 590

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1351 Availability subject to country specific rules and regulations.

1350_EN_2018_KERN[21850892]-w.indd 1351 12/17/2018 3:36:03 PM Screwdrivers \ Bit range

Bit box 32 and 61 pieces, type C 6.3

Execution: Advantage: . High-strength plastic box with opening mechanism . Special play-free clamping for optimum hold . Cross-head bits with tough torsion zone . Ident. No. 030: . Bit holder for C and E 6.3 bits . Torsion zone for reduced risk of the bits breaking . Ident. No. 040: under high stress . Bit ratchet with ﬁ ne teeth . Resistant to wear . Ident. No. 040: Bit ratchet good at getting into . 1/4”-bit direct mount Ident. No. 030 . Anti-clockwise/clockwise rotation using diﬃ cult-to-reach areas Ident. No. 040 reversing lever Drive 1/4 inch 1/4 inch Supplied slot lengths: 4.5 Supplied slot lengths: 4.5 Composition of set mm/5.5 mm/6.5 mm mm/5.5 mm/6.5 mm Sockets with socket hexagon-head tip provided 3 mm | 4 mm | 5 mm | 6 mm 4 mm | 5 mm | 6 mm Blade length (mm) 25 25 PH1 | PH2 | PH3 | PZ1 | PZ2 PH1 | PH2 | PH3 | PZ1 | PZ2 Tip size | PZ3 | TX10 | TX15 | TX20 | | PZ3 | TX10 | TX15 | TX20 | TX25 | TX30 | TX40 TX25 | TX30 | TX40 Ident. No. 030 040 52841... ● ● Prod. Gr. 590

Bit box 17 pieces, format C 6.3

Execution: . Quick-change holder with aluminium sleeve and . Box made from high-strength plastic magnet . Transparent cover with opening mechanism . Quick-change bit holder for C and E 6.3 bits Drive 1/4 inch 1/4 inch Composition of set Supplied slot lengths: 4.5 mm/6.5 mm - Sockets with socket hexagon-head tip provided 3 mm | 4 mm | 5 mm - Blade length (mm) 25 25 PH1 | PH2 | PH3 | PZ1 | PZ2 PH1 | PH2 | PH3 | PZ1 | PZ2 Tip size | PZ3 | TX10 | TX15 | TX20 | | PZ3 | TX10 | TX15 | TX20 | TX25 | TX30 TX25 | TX30 | TX40 Ident. No. 100 110 52841... ● ● Prod. Gr. 590

Bit holders

Execution: . Ident. No. 225: 2-component bit handle with circular blade and magnetic . Ident. No. 200: ¼-inch bit holder . CentroFix bit holder with special clearance-free clamping for perfect . Ident. No. 230: 2-component handle for direct mounting of both ¼” bit holders concentricity . Type C and E 6.3 Technical data: . Ident. No. 210: Quick-change bit holder for ¼” bits, type C 6.3 . Bit holder: 1/4 inch hexagon . Ident. No. 220: 2-component bit handle with hexagon blade 125 mm and magnetic ¼” bit holder

Ident. No. 220 Ident. No. 225 Ident. No. 210 Ident. No. 200 Ident. No. 230

Blade length (mm) - - 125 100 - Length (mm) 60 50 200 205 110 Ident. No. 200 210 220 225 230 52841... ● ● ● ● ● Prod. Gr. 590

Source: Hahn+Kolb Werkzeuge GmbH 1352Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1352_EN_2018_KERN[21850895]-q.indd 1352 12/17/2018 3:36:01 PM Screwdrivers \ Bit range

FlipSelector bit box Format C 6.3

Execution: Advantage: . Fibre glass-reinforced polyamide box, robust for long-term use . Tough standard bits for all kinds of screw couplings in trade and industry . Universal bit holder 1/4” with magnet . Ident. No. 111: Fitted with 12 standard bits in slotted and cross-head versions Technical data: . Drive: 1/4 inch . ﬁ tted with 12 standard bits in TX version Ident. No. 121: . Blade length: 25 mm . Ident. No. 141: ﬁ tted with 12 standard bits in TX and cross-head versions

Ident. No. 111 Ident. No. 121 Ident. No. 141

Slot length (mm) 5.5 - - TX7 | TX8 | TX9 | TX10 | TX15 | PH2 | PZ1 | PZ2 | PZ3 | TX10 | Tip size PH1 | PH2 | PH3 | PZ1 | PZ2 | PZ3 TX20 | TX25 | TX30 | TX40 TX15 | TX20 | TX25 | TX30 | TX40 Ident. No. 111 121 141 52859... ● ● ● Prod. Gr. 571

Collector bit box Format C 6.3 for safety screws

Execution: Technical data: . Torsion bit Collector, ﬁ ttings for universal use . Drive: 1/4 inch . With ClicFix ¼” quick-change holder, magnetic . Blade length: 25 mm . Tip size: PH1 PH2 PH3 PZ1 PZ2 PZ3 TX10 . Ident. No. 325: With handle for manual | | | | | | screwdriving | TX15 | TX20 | TX25 | TX30 | TX40

Supplied slot lengths: 4.5 Supplied slot lengths: 4.5 Ident. No. 325 Ident. No. 330 Composition of set mm/5.5 mm/6.5 mm mm/5.5 mm/6.5 mm/8 mm Sockets with socket hexagon-head tip provided 4 mm | 5 mm | 6 mm 3 mm | 4 mm | 5 mm | 6 mm Number of pieces in assortment/set 32 61 Ident. No. 325 330 52859... ● ● Prod. Gr. 571

BitCheck BiTorsion bit box

Execution: . Rapidaptor universal holder, 1/4”, with powerful . BiTorsion bits are tough – for a long service life permanent magnet and quick-change chuck . colour coding with easily legible size stamping . easy to operate and convenient folding holder with Technical data: . Drive: 1/4 inch bit clamping . Blade length: 25 mm

PH1 | PH2 | PH1 | PH2 | PH3 | PZ1 | Ident. No. 210 PZ1 | PZ2 | PZ2 | PZ3 | Tip size TX10 | TX15 | Ident. No. 200 TX10 | TX15 | TX20 | TX25 | TX30 TX20 | TX30 | TX40 | TX25 Number of pieces in assortment/set (PCS) 12 30 Ident. No. 200 210 52860... ● ● Prod. Gr. 542

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1353 Availability subject to country specific rules and regulations.

1352_EN_2018_KERN[21850895]-q.indd 1353 12/17/2018 3:36:03 PM Screwdrivers \ Bit range

BitCheck 30 bit box 30 pieces

Execution: Technical data: . bits are tough – for universal application . Drive: 1/4 inch . popular sizes in multiple designs . Blade length: 25 mm . Number of pieces in assortment/set: 30 PCS . easy to operate and convenient folding holder with bit clamping . universal holder, 1/4”, with powerful magnet, snap ring and stainless steel sleeve

slot lengths supplied: Composition of set - - 4.5 mm/5.5 Ident. No. 300 mm/6.5 mm Sockets with socket hexa- - 4 mm | 5 mm - gon-head tip provided | 6 mm PH1 | PH2 | PH2 | PZ1 | PH3 | PZ1 | PZ2 | PZ3 | TX10 | TX15 | PZ2 | PZ3 | Tip size TX10 | TX15 | TX20 | TX25 | TX10 | TX15 | TX20 | TX25 | TX30 | TX40 TX20 | TX25 | TX30 | TX40 TX30 | TX40 Ident. No. 300 310 320 52860... ● ● ● Prod. Gr. 542

Reversible screwdriver sets with telescopic blade System 4 and system 6

Execution: Advantage: . Blades made of chromium-vanadium-molybdenum . Handle with click-stop ball clamping for a secure steel, points colour-coded, Wiha chromium tip hold and quick changeover of blades . Ident. No. 010–040: . Blade length can be adjusted . So ﬁ nish telescopic handle, system 4 . Blade adjustment range: 18-90 mm Delivery: In textile roll-up pouch . Ident. No. 090–100: . So ﬁ nish telescopic handle, system 6 . Blade adjustment range: 42-114 mm Ident. No. 030

Composition of set Blade width: 2/3/4 mm Blade width: Blade width: Blade width: Blade width: 1.5/2/2.5/3/3.5/4 mm 1.5/2/2.5/3/3.5/4 mm - 4/6 mm 4/55/6/65 mm PH1 | PH2 | PZ1 | PH000 | PH00 | PH1 | PH2 | PH000 | PH00 | PH0 | PZ2 | 4 mm | 5 mm | PH000 | PH00 | PH0 PH0 | PH1 | TX3 | PZ1 | PZ2 | Tip size PH00 | PH0 | PH1 PH1 | 1.3 mm | 1.5 mm | 6 mm | TX10 | TX15 | PH1 TX4 | TX5 | TX6 | TX10 | TX15 | 2 mm | 2.5 mm | 3 mm | TX20 | TX25 | TX30 TX8 | TX10 TX20 | TX25 | TX40 Blade length (mm) 90 90 90 90 114 114 Number of pieces in assortment/set 4 6 11 6 6 11 Ident. No. 010 020 030 040 090 100 52686... ● ● ● ● ● ● Prod. Gr. 533

Smart reversible screwdriver set Screwdriver and T-grip function

Execution: Delivery: . Unique smart two-component handle with dual In a shock-resistant, non-slip plastic box with grip function: screwdriver and T-handle application insert possible . ¼” double blades made from heavy-duty bit steel

Composition of set Blade width: 4/5/6/7 mm Width across ﬂ ats 3 mm | 4 mm | 5 mm | 6 mm PH1 | PH2 | PH3 | PZ1 | PZ2 | PZ3 | TX6 | Tip size TX7 | TX8 | TX9 | TX10 | TX15 | TX20 | TX25 | TX30 | TX40 Length (mm) 160 Number of pieces in assortment/set 13 Ident. No. 100 52685... ● Prod. Gr. 5JF

Source: Hahn+Kolb Werkzeuge GmbH 1354Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1354_EN_2018_KERN[21850898]-r.indd 1354 12/17/2018 3:35:56 PM Screwdrivers \ Bit range

Kra form Kompakt® bit assortments Toughened version

Execution: Advantage: . Ident. No. 041–071: . Ident. No. 100: suitable bit always immediately to hand owing to easily recog- . ¼” hexagon head drive in accordance with DIN 3126, type C and E 6.3 nisable colour coding and size labelling . With quick-change chuck and holder Delivery: . Ident. No. 100: in compact and robust fabric box with Velcro closure . compact tool set with 52 screwdrivers Ident. No. 100: . bit hand-held holder and Rapidaptor with quick-change chuck . 30 BiTorsion bits with 25 mm length with colour coding Technical data: . 12 Impaktor bits with 50 mm length with colour coding . Drive: 1/4 inch . 8 Allen keys with Hex-Plus proﬁ le and ball head on long side

Ident. No. 041 Ident. No. 060 Ident. No. 070 Ident. No. 071 Ident. No. 100 Blade widths: 4.5 Composition of set - Blade width: 5.5 mm mm/5.5 mm/6.5 mm - blade width: 5.5 mm Sockets with socket hexagon-head tip 3 mm | 4 mm | 5 mm 2 mm | 2.5 mm | 3 mm - 4 mm | 5 mm | 6 mm - provided | 6 mm | 4 mm | 5 mm | 6 mm Blade length (mm) 89 89 25 25 - PH1 | PH2 | PH3 | PZ1 | PZ2 | PZ3 | TX10 | PH1 | PH2 | PH3 | PZ1 PH1 | PH2 | PH3 | PZ1 PH1 | PH2 | PH3 | PZ1 TX7 | TX8 | TX9 | TX10 TX15 | TX20 | TX25 | | PZ2 | PZ3 | TX10 | | PZ2 | PZ3 | TX10 | Tip size | PZ2 | PZ3 | TX15 | | TX15 | TX20 | TX25 | TX30 | TX40 | 1.5 mm TX15 | TX20 | TX25 TX15 | TX20 | TX25 | TX20 | TX25 | TX30 TX30 | TX40 | 2 mm | 2.5 mm | 3 | TX30 TX30 | TX40 mm | 4 mm | 5 mm | 6 mm | 8 mm Number of pieces in assortment/set 11 17 32 32 52 Ident. No. 041 060 070 071 100 52857... ● ● ● ● ● Prod. Gr. 542 Magazine bit holder

Execution: Advantage: . Telescopic bit magazine equipped with 7 bits . Seam-free, smooth cap for minimum friction . Bit holder with magnetic mount, 1/4” . Ergonomic easy-grip so coating for optimum torques Slot width (mm) 5.5 Tip size PH1 | PH2 | PZ1 | PZ2 Blade length (mm) 112 Length (mm) 217 Ident. No. 100 52853... ● Prod. Gr. 590 Bit holder Stainless steel

Execution: . KRAFTGRIFF in cellulose acetate, impact-resistant, . 1/4” mount with powerful permanent magnet. red, no cadmium . Magazine holder ﬁ tted with 6 diﬀ erent bits Advantage: . Chrome-vanadium steel shank, encased in plastic . Transparent selector disc prevents extended searching for bits and bits from falling out Composition of set Slot width: 45/6/8 mm Tip size PH1 | PH2 | PH3 Blade length (mm) 120 Length (mm) 230 Ident. No. 010 52854... ●

Prod. Gr. 571

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1355 Availability subject to country specific rules and regulations.

1354_EN_2018_KERN[21850898]-r.indd 1355 12/17/2018 3:36:02 PM Screwdrivers \ Bit range

Bit holder Stainless steel

Execution: . Ident. No. 140: With ﬂ exible shank and snap ring for angled screws . Ident. No. 090: Magnetic, with short, round shank . Ident. No. 110–120: Hexagonal shank, chrome-vanadium steel, bright nick- Technical data: el-plated, with powerful permanent magnet . Bit holder: 1/4 inch hexagon

Ident. No. 110–120 Ident. No. 140

Ident. No. 090

Blade length (mm) 7 125 300 150 Length (mm) 57 225 400 268 Ident. No. 090 110 120 140 52854... ● ● ● ● Prod. Gr. 571

Magazine bit holder

Execution: . Ergonomic multi-component handle with roll-oﬀ . Bit magazine integrated in the handle to hold 8 bits protection . Swivel-open ﬂ ap for removal . Uninsulated blade . Mount ,1/4”, with magnet Slot width (mm) 6.5 Tip size PH1 | PH2 | PH3 | PZ2 | TX15 | TX20 | TX25 Blade length (mm) 125 Length (mm) 225 Ident. No. 200 52854... ● Prod. Gr. 571 Stubby magazine bit holder

Execution: . ¼” magnetic bit mount . Technical data: Ergonomic So -Finish short handle for working in . Blade length: 25 mm conﬁ ned areas . Length: 57 mm . Bit magazine with six bits in the handle Blade widths: 4.5 mm/6.5 Composition of set - mm/8 mm PH1 | PH2 | PH3 | PZ1 | PZ2 Tip size PZ1 | PZ2 | PZ3 | PZ3 Ident. No. 400 450 52854... ● ● Prod. Gr. 571 Li Up magazine bit holder

Execution: Advantage: . Ident. No. 200: . Ident. No. 200: 12 bits ready to hand and stored in compact handle . Magnetic bit holder . Ident. No. 250: no more searching, the most popular bits in a single tool . For 25-mm standard bits 1/4” . Ident. No. 300: . Bit magazine opens by pushing the button . So Finish electric multi-component handle with roll-oﬀ protection . Ident. No. 250: . Protective insulation sprayed directly onto the blade, completely integrated . magnetic bit holder in the blade in the front section . equipped with 13 double bits – i.e. 26 drive sizes . slimBits stored in compartments for easy access . bit magazine opens by pushing the button . large handle – maximum power Technical data: . Ident. No. 300: . Length: 195 mm . VDE-insulated, metal ClicFix bit holder reliably secures all slimBits . Material of the grip handle: 2-component plastic . Individually tested protective insulation 1000 V AC, VDE and GS certiﬁ ed . Internal bit magazine with 6 slots

Ident. No. 250 Ident. No. 200 Ident. No. 300

Source: Hahn+Kolb Werkzeuge GmbH 1356Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1356_EN_2018_KERN[21850901]-t.indd 1356 12/17/2018 3:35:56 PM Screwdrivers \ Bit range

blade width 4.0 mm/6.0 mm, square Composition of set Blade width: 5.5 mm 1.0/2.0 Cutting width 3.0/4.0/5.5 mm 3 mm | 4 mm | 5 mm | 6 mm | Width across ﬂ ats 3 mm | 4 mm | 5 mm 3/32 inch | 7/64 inch | 1/8 inch | - 9/64 inch | 5/32 inch | 3/16 inch PH0 | PH1 | PH2 | PH3 | PZ1 | PH2 | PZ1 | PZ2 | PZ3 | TX15 | Tip size PZ2 | TX10 | TX15 | TX20 | TX25 | PH1 | PH2 | PZ2 + slot TX20 | TX25 | TX30 TX27 | TX30 Blade length (mm) 25 - 70 Ident. No. 200 250 300 52855... ● ● ● Prod. Gr. 571 Kra form Kompakt ratchet screwdrivers

Execution: . ¼” quick-change chuck; mount with magnet . Fine-toothed ratchet for a low return angle . 16 bits 89 mm in length . Reversing ring (right, le , ﬁ xed) . Also suitable for cordless screwdrivers . Maximum torque up to 50 Nm . Ident. No. 015: . With 6-mm hexagon socket direct mount . Ident. No. 005: . 7 double blades 175 mm in length . Integrated ﬁ xed bit mount blade (¼” mount) . Bit changeover magazine integrated in handle Delivery: . Ident. No. 010: Ident. No. 010–015: In textile bag

Ident. No. 005

Ident. No. 010 Ident. No. 015

Composition of set Blade widths: 55/65 mm Blade widths: 5.5 mm Blade widths: 4/6 mm Width across ﬂ ats - 3 mm | 4 mm | 5 mm | 6 mm - PH1 | PH2 | PH3 | PZ1 | PZ2 | PH1 | PH2 | PZ1 | PZ2 | TX10 | Tip size PH1 | PH2 | PZ1 | PZ2 TX10 | TX15 | TX20 | TX25 | TX30 TX15 Blade length (mm) 25 89 175 Length (mm) 150 150 200 Ident. No. 005 010 015 52856... ● ● ● Prod. Gr. 542 Magazine bit holder screwdriver Kra form Kompakt 20 for 1/4 inch bits

Execution: Delivery: . telescopic blade can be locked in 2 steps with sturdy belt textile pouch with loop closure . integrated bit magazine equipped with 6 bits 1/4 inch, 25 mm Technical data: . blade also suitable for machine application . Tip size: PH1 | PH2 | PZ1 | PZ2 | TX25 | Slot 5.5mm . Kra form handle with roll-away protection . Blade length: 100 mm . high-quality BiTorsion bits with colour coding

Ident. No. 300 52856... ● Prod. Gr. 542 Bit ratchet set

Execution: . total length 250 mm blade length 127 mm . can be adjusted right, le or ﬁ xed via reversing ring . adapter for hexagonal inserts . 1/4” hexagon socket with magnet for easy bit . clear tool arrangement with practical empty changes compartment . high-load ratchet mechanism with 48 teeth Delivery: . ergonomically shaped non-slip handle in robust plastic box with foam insert Composition of set blade widths 4.5/5.5/6.5 mm Width across ﬂ ats 4 mm | 5 mm | 5.5 mm | 6 mm | 7 mm | 8 mm | 10 mm | 11 mm | 13 mm 4 mm | 5 mm | 6 mm | PH1 | PH2 | PH3 | Tip size PZ1 | PZ2 | PZ3 | TX10 | TX15 | TX20 | TX25 | TX30 | TX40 Blade length (mm) 25 Number of pieces in assortment/set 29 Material of the grip handle 2-component plastic Ident. No. 010 52857... ● Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1357 Availability subject to country specific rules and regulations.

1356_EN_2018_KERN[21850901]-t.indd 1357 12/17/2018 3:36:01 PM Screwdrivers \ Pipe socket spanners

Hexagonal socket spanners

Execution: Ident. No. 100 . With 2-component handle . Hardened and brushed chromium-plated blade

Width across ﬂ ats 4 mm 5 mm 5.5 mm 6 mm 7 mm 8 mm 9 mm 10 mm Blade length (mm) 125 125 125 125 125 125 125 125 Length (mm) 217 217 217 217 217 217 217 217 2-component 2-component 2-component 2-component 2-component 2-component 2-component 2-component Material of the grip handle plastic plastic plastic plastic plastic plastic plastic plastic Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-vana- Chrome-vana- Chrome-vana- Chrome-vana- Chrome-vana- Chrome-vana- Chrome-vana- Chrome-vana- Material dium steel dium steel dium steel dium steel dium steel dium steel dium steel dium steel Ident. No. 040 050 055 060 070 080 090 100 52159... ● ● ● ● ● ● ● ● Width across ﬂ ats 11 mm 12 mm 13 mm Blade length (mm) 125 125 125 Length (mm) 227 227 227 2-component 2-component 2-component Material of the grip handle plastic plastic plastic Surface Chrome-plated Chrome-plated Chrome-plated Chrome-vana- Chrome-vana- Chrome-vana- Material dium steel dium steel dium steel Ident. No. 110 120 130 52159... ● ● ● Prod. Gr. 590 VE hexagon socket wrenches ( DIN 7445 ) Safety isolation to DIN EN 60900, isolated to 1000 V, tested safety ‘GS’, individually tested

Execution: Technical data: . Inner bore for protruding bolts . Blade length: 125 mm . Blade insulation . Material of the grip handle: 2-component plastic . Surface: VDE insulated . Sprayed directly on the blade . Material: Chrome-vanadium steel . So Finish® handle . VDE certifi ed: Yes Width across fl ats 4 mm 5 mm 5.5 mm 6 mm 7 mm 8 mm 9 mm 10 mm Length (mm) 236 236 236 236 243 243 243 243 Ident. No. 240 250 255 260 270 280 290 300 52161... ● ● ● ● ● ● ● ● Width across fl ats 11 mm 12 mm 13 mm 14 mm 15 mm 16 mm 17 mm Length (mm) 243 243 243 243 243 243 243 Ident. No. 310 320 330 340 350 360 370 52161... ● ● ● ● ● ● ● Prod. Gr. 533

VDE hexagon socket wrench set ( DIN 7445 ) Safety isolation to DIN EN 60900, isolated to 1000 V, tested safety ‘GS’, individually tested

Execution: . Sprayed directly on the blade . Inner bore for protruding bolts . So Finish® handle . Blade insulation Composition of set Supplied lengths: 236-243 mm Width across ﬂ ats 5.5 mm | 7 mm | 8 mm | 10 mm | 13 mm Blade length (mm) 125 Material of the grip handle 2-component plastic Surface VDE insulated Material Chrome-vanadium steel VDE certiﬁ ed Yes Ident. No. 510 52161... ● Prod. Gr. 533

Hexagonal socket spanners chromium-vanadium steel blade

Execution: Technical data: . Hardened . Blade length: 65 mm . Inner bore for protruding bolts . Material of the grip handle: 2-component plastic . Surface: Chrome-plated . Short version . Material: Chrome-vanadium steel . So Finish® handle

Width across ﬂ ats 5.5 mm 6 mm 7 mm 8 mm 10 mm Length (mm) 176 176 183 183 183 Ident. No. 055 060 070 080 100 52162... ● ● ● ● ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH 1358Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1358_EN_2018_KERN[21850905]-p.indd 1358 12/17/2018 3:35:56 PM Screwdrivers \ Pipe socket spanners

Hexagonal socket spanners

Execution: Technical data: . Flexible shank for angled screws . Material of the grip handle: 2-component plastic . Bright nickel-plated head . Surface: Nickel-plated . Material: Chrome-vanadium steel . So Finish® handle

Width across ﬂ ats 5 mm 5.5 mm 6 mm 7 mm 8 mm 10 mm 13 mm Blade length (mm) 150 150 150 150 150 175 175 Length (mm) 261 261 261 268 268 293 293 Ident. No. 050 055 060 070 080 100 130 52163... ● ● ● ● ● ● ● Prod. Gr. 533

Hexagon socket wrench sets In textile tool roll

Execution: . System 6 So Finish® telescopic handle . Variable blade length from 42 mm to 114 mm . Blades hardened throughout with stamped drive . Click-Stop ball clamping guarantees a secure hold sizes

4 mm | 4.5 mm | 5 mm | 5.5 5 mm | 5.5 mm | 6 mm | mm | 6 mm | 7 mm | 8 mm Width across ﬂ ats 7 mm | 8 mm | 10 mm | | 9 mm | 10 mm | 11 mm | 13 mm 13 mm Blade length (mm) 140 140 Material of the grip handle 2-component plastic 2-component plastic Material Chrome-vanadium steel Chrome-vanadium steel Number of pieces in assortment/set 8 12 Ident. No. 120 Ident. No. 080 120 52165... ● ● Prod. Gr. 533

Hexagonal socket spanners With hexagonal collar

Execution: Technical data: . Inner bore for protruding bolts . Blade length: 125 mm . So Finish® handle . Material of the grip handle: 2-component plastic . Surface: Chrome-plated . Material: Chrome-vanadium steel

Width across ﬂ ats 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm Length (mm) 238 238 238 238 246 246 246 Ident. No. 070 080 090 100 110 120 130 52166... ● ● ● ● ● ● ● Prod. Gr. 533

Hexagonal socket wrench with T-handle with 2-component handle

Execution: . Blade made of special CrV and CrMV alloy . Comfortable non-slip so coating provides for . Optimal performance data up to 100% above DIN optimal power transmission values . Hard core for lasting blade/handle connection . Matt chrome-plated blade even under the highest loads . With hole for hanging Ident. No. 410–444

Ident. No. 450–510

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1359 Availability subject to country specific rules and regulations.

1358_EN_2018_KERN[21850905]-p.indd 1359 12/17/2018 3:35:59 PM Screwdrivers \ Pipe socket spanners

Width across fl ats 7 mm 8 mm 8 mm 8 mm 9 mm 9 mm 10 mm 10 mm Blade length (mm) 125 125 230 350 125 230 125 230 2-component 2-component 2-component 2-component 2-component 2-component 2-component 2-component Material of the grip handle plastic plastic plastic plastic plastic plastic plastic plastic Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Ident. No. 410 420 422 424 430 432 440 442 52167... ● ● ● ● ● ● ● ● Width across fl ats 10 mm 11 mm 11 mm 12 mm 12 mm 13 mm 13 mm 13 mm Blade length (mm) 350 125 230 125 230 125 230 350 2-component 2-component 2-component 2-component 2-component 2-component 2-component 2-component Material of the grip handle plastic plastic plastic plastic plastic plastic plastic plastic Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Ident. No. 444 450 452 460 462 470 472 474 52167... ● ● ● ● ● ● ● ● Width across fl ats 14 mm 15 mm 16 mm 17 mm Blade length (mm) 125 125 125 125 2-component 2-component 2-component 2-component Material of the grip handle plastic plastic plastic plastic Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Ident. No. 480 490 500 510 52167... ● ● ● ● Prod. Gr. 590

Hexagonal socket spanners with T-handle

Execution: Technical data: . Inner bore for protruding bolts . Material of the grip handle: 1-component plastic . Surface: Nickel-plated . Material: Chrome-vanadium steel

Width across fl ats 5.5 mm 6 mm 7 mm 8 mm 8 mm 8 mm 9 mm 9 mm Blade length (mm) 125 125 125 125 200 350 125 200 Length (mm) 157 157 157 157 232 382 157 232 Ident. No. 055 060 070 080 082 084 090 092 52167... ● ● ● ● ● ● ● ● Width across fl ats 10 mm 10 mm 10 mm 11 mm 12 mm 13 mm 13 mm 13 mm Blade length (mm) 125 200 350 125 125 125 230 350 Length (mm) 157 232 382 157 157 157 262 382 Ident. No. 100 102 104 110 120 130 132 134 52167... ● ● ● ● ● ● ● ● Width across fl ats 14 mm 15 mm 16 mm 17 mm Blade length (mm) 125 125 125 125 Length (mm) 157 157 157 157 Ident. No. 140 150 160 170 52167... ● ● ● ● Prod. Gr. 533

Source: Hahn+Kolb Werkzeuge GmbH 1360Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1358_EN_2018_KERN[21850905]-p.indd 1360 12/17/2018 3:36:00 PM Screwdrivers \ Pipe socket spanners

Hexagon socket wrench set With T-handle

Execution: . Inner bore for protruding bolts

Composition of set Supplied lengths: 157 mm Width across ﬂ ats 6 mm | 7 mm | 8 mm | 10 mm | 13 mm Blade length (mm) 125 Material of the grip handle 1-component plastic Surface Nickel-plated Material Chrome-vanadium steel Ident. No. 300 52167... ● Prod. Gr. 533

Hexagon tubular socket spanners Seamless, made of hardened, chrome-plated C35

Application: Technical data: Ideally suited for far-projecting threaded pins. . Surface: Chrome-plated . Material: Hardened steel Execution: . Impact-resistant plastic handle

Width across ﬂ ats 4 mm 4.5 mm 5 mm 5.5 mm 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm Length (mm) 210 210 210 210 220 220 220 220 230 230 230 230 240 Hole Ø of mount (mm) 3 3 3 3 6.3 6.3 6.3 6.3 6.3 6.3 8.5 8.5 8.5 Ident. No. 510 520 530 540 550 560 570 580 590 600 610 620 630 52168... ● ● ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 526

Hexagon socket wrench

Execution: . Material of the grip handle: 1-component plastic . Inner bore for protruding threaded sha s . Surface: Nickel-plated . Material: Chrome-vanadium steel Technical data:

Width across ﬂ ats 7 mm 8 mm 10 mm 10 mm 13 mm Blade length (mm) 125 125 125 200 125 Length (mm) 157 157 157 232 157 Ident. No. 010 020 040 050 060 52169... ● ● ● ● ● Prod. Gr. 526

Hexagon tubular socket spanners

Execution: Technical data: . Made from steel pipe . Material: Steel pipe . Unhardened

Width across fl ats 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm 14 mm 17 mm Length (mm) 100 110 120 120 140 140 140 150 Hole Ø of mount (mm) 6 6 6 6 8 8 8 10 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Ident. No. 080 090 100 110 120 130 140 170 52174... ● ● ● ● ● ● ● ● Width across fl ats 19 mm 22 mm 24 mm 27 mm 30 mm 32 mm 36 mm 41 mm Length (mm) 160 170 180 190 200 210 220 240 Hole Ø of mount (mm) 12 12 14 14 16 16 18 18 Surface Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Chrome-plated Ident. No. 190 220 240 270 300 320 360 410 52174... ● ● ● ● ● ● ● ● Width across fl ats 46 mm 50 mm 55 mm 60 mm 65 mm 70 mm Length (mm) 245 245 245 250 250 250 Hole Ø of mount (mm) 20 20 20 25 25 25 Surface Lacquered Lacquered Lacquered Lacquered Lacquered Lacquered Ident. No. 460 500 550 600 650 700 52174... ● ● ● ● ● ●

Prod. Gr. 526

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1361 Availability subject to country specific rules and regulations.

1361_EN_2018_KERN[21850909]-s.indd 1361 12/17/2018 3:35:56 PM Screwdrivers \ Pipe socket spanners

Hexagon tubular socket wrench ( DIN 896 ) Made of C35 steel

Execution: Technical data: . Hardened . Surface: Chrome-plated . With tommy bar hole on both sides . Material: Hardened steel

Width across fl ats 6 x 7 mm 7 x 8 mm 8 x 9 mm 8 x 10 mm 9 x 10 mm 10 x 11 mm 10 x 13 mm 11 x 13 mm Length (mm) 100 100 100 120 120 120 140 140 Hole Ø of mount (mm) 6 6 6 6 6 6 8 8 Ident. No. 020 030 040 050 060 080 100 120 52176... ● ● ● ● ● ● ● ● Width across fl ats 12 x 13 mm 12 x 14 mm 13 x 14 mm 13 x 15 mm 13 x 17 mm 14 x 15 mm 14 x 17 mm 16 x 17 mm Length (mm) 140 140 140 140 150 140 150 150 Hole Ø of mount (mm) 8 8 8 8 10 8 10 10 Ident. No. 140 150 155 160 170 180 190 200 52176... ● ● ● ● ● ● ● ● Width across fl ats 17 x 19 mm 18 x 19 mm 19 x 22 mm 20 x 22 mm 21 x 23 mm 22 x 24 mm 24 x 26 mm 24 x 27 mm Length (mm) 160 160 170 170 170 180 180 180 Hole Ø of mount (mm) 12 12 12 12 14 14 14 14 Ident. No. 210 230 240 260 270 280 300 310 52176... ● ● ● ● ● ● ● ● Width across fl ats 25 x 28 mm 27 x 30 mm 27 x 32 mm 30 x 32 mm 30 x 36 mm 32 x 36 mm 36 x 41 mm 41 x 46 mm Length (mm) 180 200 200 200 220 220 245 245 Hole Ø of mount (mm) 16 16 16 16 18 18 18 20 Ident. No. 330 350 360 370 380 390 400 410 52176... ● ● ● ● ● ● ● ● Width across fl ats 46 x 50 mm Length (mm) 245 Hole Ø of mount (mm) 20 Ident. No. 420 52176... ● Prod. Gr. 526

Hexagon tubular socket wrench set ( DIN 896 )

Execution: Delivery: . With stepped tommy bar In cardboard packaging . Hardened . With tommy bar hole on both sides

lengths supplied: Supplied lengths: 100 Supplied lengths: 100 Composition of set 100–150 mm - 170 mm - 200 mm 6 x 7 mm | 8 x 9 mm | 10 x 11 mm | 12 x 6 x 7 mm | 8 x 9 mm 6 x 7 mm | 8 x 9 mm 13 mm | 14 x 15 mm | 10 x 11 mm | 12 x | 10 x 11 mm | 12 x | 16 x 17 mm | 18 x Width across ﬂ ats 13 mm | 14 x 15 mm 13 mm | 14 x 15 mm 19 mm | 20 x 22 mm | 16 x 17 mm | 18 x | 16 x 17 mm | 21 x 23 mm | 24 x 19 mm | 20 x 22 mm 26 mm | 25 x 28 mm | 30 x 32 mm Hole Ø of mount (mm) 10 12 16 Surface Chrome-plated Chrome-plated Chrome-plated Material Hardened steel Hardened steel Hardened steel Number of pieces in assortment/set 6 8 12 Ident. No. 100 120 200 52178... ● ● ● Prod. Gr. 526

Source: Hahn+Kolb Werkzeuge GmbH 1362Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1361_EN_2018_KERN[21850909]-s.indd 1362 12/17/2018 3:35:57 PM Screwdrivers \ Pipe socket spanners

Cranked box spanner Hollow curved version

Execution: . With identical wrench sizes Technical data: . Can also be used with plug-in tommy bar . Surface: Chrome-plated Advantage: . Material: Chrome-vanadium steel . The hollow shape allows deep screws and nuts to be tightened/loosened

Width across fl ats 6 mm 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm Length (mm) 105 110 115 122 130 136 145 152 Hole Ø of mount (mm) 6 6 6 6 8 8 8 8 Head Ø (mm) 10 12 13 14 15.5 16.5 18 19.5 Ident. No. 506 507 508 509 510 511 512 513 52183... ● ● ● ● ● ● ● ● Width across fl ats 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm 21 mm 22 mm Length (mm) 160 170 178 187 195 205 225 230 Hole Ø of mount (mm) 10 10 12 12 12 14 14 14 Head Ø (mm) 21 22.5 24 25.5 26.5 28 32 32 Ident. No. 514 515 516 517 518 519 521 522 52183... ● ● ● ● ● ● ● ● Width across fl ats 24 mm 27 mm 30 mm 32 mm Length (mm) 250 280 310 330 Hole Ø of mount (mm) 18 20 20 20 Head Ø (mm) 30.3 38 42 45 Ident. No. 524 527 530 532 52183... ● ● ● ● Prod. Gr. 526

Construction and electrical MasterKey

Application: . With reversible bit Suitable for actuating locking systems in the areas of . Bottle opener function facilities engineering, gas and water supply systems and shut-oﬀ systems. Technical data: . Slot width: 7 mm Execution: . Made from die-cast zinc

TwinKey universal key

Application: . 2 crosses Suitable for actuating locking systems in the areas of . 1 key — for all standard locking systems and sizes facilities engineering, gas and water supply systems . 8-leg version that is connected via magnet to save and shut-oﬀ systems. space and secured via a robust stainless steel wire cable Execution: . 10 proﬁ les

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1363 Availability subject to country specific rules and regulations.

1363_EN_2018_KERN[21850912]-s.indd 1363 12/17/2018 3:35:58 PM Screwdrivers \ Pipe socket spanners

Universal keys

Application: . Ident. No. 015: With carabiner hooks on chain Ident. No. 010: For switch cabinets or masts and for all building trades. . Ident. No. 100: Ident. No. 012–100: For switch cabinets or rods and for all building trades . Plastic body with die-cast insert . With shirt clip Execution: . Made from die-cast zinc

Ident. No. 012 Ident. No. 100

Torque screwdriver For plug-in blades

Execution: . robust aluminium sealing cap with easily readable . precise and simple adjustment adjustment scale . audible and haptic release when the set torque is Delivery: reached certiﬁ cate, user manual and adjustment key . ergonomically shaped handle for optimum force transmission Min./max. torque measuring range 0.6-1.5 Nm 1.5-3.0 Nm 3.0-5.4 Nm Scale value (nm) 0.1 0.1 0.1 Blade Ø 1/4 1/4 1/4 Handle length (mm) 105 105 105 Material of the grip handle 2-component plastic 2-component plastic 2-component plastic Error limit (%) (%) 6 6 6 Calibration certiﬁ cate Yes Yes Yes Ident. No. 011 021 031 52200... ● ● ● Prod. Gr. 5HC

Torque screwdriver set For plug-in blades

Execution: . robust aluminium sealing cap with easily readable . set of 2 torque screwdriver handles: 0.6 Nm to adjustment scale 1.5 Nm and 1.5 Nm to 3.0 Nm Delivery: . complete with adjustment tool, bit retention blade with certifi cate and directions, in impact-resistant and 10 1/4” bits plastic box with foam insert . error limit: +/- 6% Min./max. torque measuring range 0.6-3.0 Nm Scale value (nm) 0.1 Tip size PH1 | PH2 | PZ1 | PZ2 | TX10 | TX15 | TX20 | TX25 Handle length (mm) 105 Material of the grip handle 2-component plastic Width across fl ats 2.5 mm | 3 mm Error limit (%) (%) 6 Calibration certifi cate Yes Ident. No. 061 52200... ● Prod. Gr. 5HC

Source: Hahn+Kolb Werkzeuge GmbH 1364Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1363_EN_2018_KERN[21850912]-s.indd 1364 12/17/2018 3:36:04 PM Screwdrivers \ Torque screwdriver

Blades for slotted screws For torque screwdrivers no. 52200 010-030

Execution: Technical data: . Blade diameter 1/4” . Blade length: 170 mm . Blade diameter: 1/4 in

Width of cutting edge (mm) 3.0 3.5 4.0 Ident. No. 230 235 240 52200... ● ● ● Prod. Gr. 5HC Accessories for 52200 230 52200 235 52200 240 011 011 011 ● ● ● 52200... torque screwdriver for Ident. No. 021 021 021 1/4” plug-in blades ● ● ● 031 031 031 ● ● ● Blades for Phillips screws For torque screwdrivers no. 52200 010-030

Application: Technical data: For PHILLIPS screws . Blade length: 170 mm . Blade diameter: 1/4 in Execution: . Blade diameter 1/4” Tip size PH0 PH1 PH2 PZ0 PZ1 PZ2 Ident. No. 300 301 302 310 311 312 52200... ● ● ● ● ● ● Prod. Gr. 5HC Accessories for 52200 300 52200 301 52200 302 52200 310 52200 311 52200 312 011 011 011 011 011 011 ● ● ● ● ● ● 52200... torque screwdriver for Ident. No. 021 021 021 021 021 021 1/4” plug-in blades ● ● ● ● ● ● 031 031 031 031 031 031 ● ● ● ● ● ●

Blades for hexagon socket screws For torque screwdrivers no. 52200 010-030

Execution: Technical data: . Blade diameter 1/4” . Blade length: 170 mm . Blade diameter: 1/4 in Width across ﬂ ats 1.5 mm 2 mm 2.5 mm 3 mm 4 mm Ident. No. 315 320 325 330 340 52200... ● ● ● ● ● Prod. Gr. 5HC Accessories for 52200 315 52200 320 52200 325 52200 330 52200 340 011 011 011 011 011 ● ● ● ● ● 52200... torque screwdriver for Ident. No. 021 021 021 021 021 1/4” plug-in blades ● ● ● ● ● 031 031 031 031 031 ● ● ● ● ●

Blades for TX and TX-Plus® screws For torque screwdrivers no. 52200 010-030

Application: Ident. No. 106–125: for TX screws Ident. No. 206–225: for TX Plus screws. Technical data: . Blade length: 170 mm Execution: . Blade diameter: 1/4 in . Blade diameter 1/4”

Tip size TX6 TX7 TX8 TX9 TX10 TX15 TX20 TX25 Ident. No. 106 107 108 109 110 115 120 125 52200... ● ● ● ● ● ● ● ● Tip size TXP6 TXP7 TXP8 TXP9 TXP10 TXP15 TXP20 TXP25 Ident. No. 206 207 208 209 210 215 220 225 52200... ● ● ● ● ● ● ● ● Prod. Gr. 5HC

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1365 Availability subject to country specific rules and regulations.

1363_EN_2018_KERN[21850912]-s.indd 1365 12/17/2018 3:36:04 PM Screwdrivers \ Torque screwdriver

Accessories for 52200 106 52200 107 52200 108 52200 109 52200 110 52200 115 52200 120 011 011 011 011 011 011 011 ● ● ● ● ● ● ● 52200... torque screwdriver for Ident. No. 021 021 021 021 021 021 021 1/4” plug-in blades ● ● ● ● ● ● ● 031 031 031 031 031 031 031 ● ● ● ● ● ● ● Accessories for 52200 125 52200 206 52200 207 52200 208 52200 209 52200 210 52200 215 011 011 011 011 011 011 011 ● ● ● ● ● ● ● 52200... torque screwdriver for Ident. No. 021 021 021 021 021 021 021 1/4” plug-in blades ● ● ● ● ● ● ● 031 031 031 031 031 031 031 ● ● ● ● ● ● ● Accessories for 52200 220 52200 225 011 011 ● ● 52200... torque screwdriver for Ident. No. 021 021 1/4” plug-in blades ● ● 031 031 ● ●

Bit holder For torque screwdrivers no. 52200 010-030

Execution: . Blade diameter 1/4”

Blade length (mm) 170 Blade Ø 1/4 Ident. No. 400 52200... ● Prod. Gr. 5HC Accessories for 52200 400 011 ● 52200... torque screwdriver for Ident. No. 021 1/4” plug-in blades ● 031 ●

Easy Torque torque screwdrivers Fixed factory torque setting

Execution: Delivery: . Click signal on reaching the set torque value calibration certifi cate . Quick identifi cation by printed marking on end of handle Technical data: . Handle length: 130 mm Advantage: . Material of the grip handle: 2-component plastic . Handle enables optimum force transmission . Error limit (%): 10 % . Unlimited opening torque . Calibration certifi cate: No . Mechanism resistant to industrial lubricants Max. torque measuring range (Nm) 0.5 0.6 0.9 1.1 1.2 1.4 2 2.5 3 3.8 4 4.5 5 Ident. No. 005 006 009 011 012 014 021 025 030 038 040 045 050 52201... ● ● ● ● ● ● ● ● ● ● ● ● ● Prod. Gr. 537

Torque screwdriver TorqueVario®-S with scale, with calibration certiﬁ cate

Execution: Delivery: . Variable torque adjustment With adjustment tool . With scale . So Finish® handle Technical data: . Blade diameter: 4 mm . Automatic release and click signal . Material of the grip handle: 2-component plastic Advantage: . Calibration certiﬁ cate: Yes . Compact and particularly lightweight design

Min./max. torque measuring range 0.1-0.6 Nm 0.4-1 Nm 0.5-2 Nm 0.8-5 Nm Scale value 0.02 - - - Handle length (mm) 127 127 131 138 Error limit (%) (%) 10 6 6 6 Ident. No. 130 140 150 160 52206... ● ● ● ● Prod. Gr. 537

Source: Hahn+Kolb Werkzeuge GmbH 1366Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1363_EN_2018_KERN[21850912]-s.indd 1366 12/17/2018 3:36:05 PM Screwdrivers \ Torque screwdriver

Torque screwdriver set TorqueVario®-S with scale, with calibration certiﬁ cate

Delivery: Torque screwdriver no. 52206 160, universal bit holder, setting tool, in robust metal box Min./max. torque measuring range 1-5 Nm Tip size PH1 | PH2 | PZ1 | PZ2 | TX10 | TX15 | TX20 | TX25 Blade length (mm) 170 Handle length (mm) 138 Material of the grip handle 2-component plastic Width across fl ats 2.5 mm | 3 mm Error limit (%) (%) 6 Calibration certifi cate Yes Ident. No. 190 52206... ● Prod. Gr. 537 Torque screwdriver TorqueFix®, with calibration certifi cate

Execution: . With ﬁ xed, preset torque . Technical data: So Finish® handle . Material of the grip handle: 2-component plastic . Automatic release and click signal . Error limit (%): 6 % . Calibration certiﬁ cate: Yes Advantage: . Compact and particularly lightweight design

Max. torque measuring range (Nm) 0.15 0.4 0.5 0.6 0.8 0.9 1.1 1.2 Handle length (mm) 112 112 112 112 112 112 119 119 Ident. No. 001 004 005 006 008 009 011 012 52207... ● ● ● ● ● ● ● ● Max. torque measuring range (Nm) 1.5 2 2.5 3 3.8 5 5.5 7.2 Handle length (mm) 119 119 119 126 126 132 132 132 Ident. No. 015 020 025 030 038 050 055 072 52207... ● ● ● ● ● ● ● ● Prod. Gr. 537

iTorque mechatronic torque screwdrivers With calibration certiﬁ cate

Application: Advantage: For controlled screwing at speciﬁ ed torques, in . Extra: Click Control — integrated counter records combination with a Wiha torque 4-mm interchange- each application able blade. . Large digital display for easy, continuous torque value adjustment Execution: . Easy to switch units (Nm square to lbs/Ncm square . Torque value settable via digital scale to oz) . Automatic release . Comfortable torque setting using knob directly Delivery: integrated into the handle With ¼-inch bit holder blade . Ergonomic plastic/metal compound grip made from high-quality, robust materials Technical data: . Clearly audible and feelable click signal when the . Blade diameter: 4 mm set torque is reached . Handle length: 134 mm . Material of the grip handle: 2-component plastic . Calibration alarm a er every 5000 applications . Error limit (%): 6 % (standard guideline value/resettable) . Calibration certiﬁ cate: Yes . Accuracy: ± 6%, based on national standards Min./max. torque measuring range 0.4-1.5 Nm 0.8-3 Nm Ident. No. 010 020 52205... ● ● Prod. Gr. 537 Blades for slotted screws for torque screwdrivers no. 52201005-050/52206130-190/52207001-072/52205010-020

Execution: Technical data: . Hexagon mount . Blade length: 175 mm . Blade diameter: 4 mm Width of cutting edge (mm) 1.5 2 2.5 3 3.5 4 Ident. No. 115 120 125 130 135 140 52207... ● ● ● ● ● ● Prod. Gr. 537

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1367 Availability subject to country specific rules and regulations.

1367_EN_2018_KERN[21850917]-w.indd 1367 12/17/2018 3:35:55 PM Screwdrivers \ Torque screwdriver

Blades for Phillips screws for torque screwdrivers no. 52201005-050/52206130-190/52207001-072/52205010-020

Application: Technical data: Ident. No. 200–220: For PHILLIPS screws . Blade length: 175 mm Ident. No. 300–320: For POZIDRIV screws . Blade diameter: 4 mm Ident. No. 200–220

Execution: . Hexagon mount Ident. No. 300–320 Tip size PH0 PH00 PH000 PH1 PH2 PZ0 PZ1 PZ2 Ident. No. 200 202 204 210 220 300 310 320 52207... ● ● ● ● ● ● ● ● Prod. Gr. 537

Blades for TX screws for torque screwdrivers no. 52201005-050/52206130-190/52207001-072/52205010-020

Execution: Technical data: . Hexagon mount . Blade length: 175 mm . Blade diameter: 4 mm

Tip size TX5 TX6 TX7 TX8 TX9 TX10 TX15 TX20 TX25 TORX Ident. No. 405 406 407 408 409 410 415 420 425 52207... ● ● ● ● ● ● ● ● ● TORX with Ident. No. - 436 437 438 439 440 445 450 455 52207... MagicSpring ● ● ● ● ● ● ● ● Prod. Gr. 537

Blades for TX-Plus screws for torque screwdrivers no. 52201005-050/52206130-190/52207001-072/52205010-020

Application: Technical data: for TX Plus screws . Blade length: 175 mm . Blade diameter: 4 mm Execution: . Hexagon mount Tip size TXP5 TXP6 TXP7 TXP8 TXP9 TXP10 TXP15 TXP20 TXP25 TORX plus Ident. No. 505 506 507 508 509 510 515 520 525 52207... ● ● ● ● ● ● ● ● ● TORX plus Ident. No. - 556 557 558 559 560 565 570 575 52207... MagicSpring ● ● ● ● ● ● ● ● Prod. Gr. 537

Blades for hexagon socket screws for torque screwdrivers no. 52201005-050/52206130-190/52207001-072/52205010-020

Execution: Technical data: . Hexagon socket . Blade length: 175 mm . Hexagon mount . Blade diameter: 4 mm

Width across ﬂ ats 1.5 mm 2 mm 2.5 mm 3 mm 4 mm Without ball Ident. No. 615 620 625 630 640 52207... end ● ● ● ● ● With ball end Ident. No. 715 720 725 730 740 52207... ● ● ● ● ● Prod. Gr. 537

Source: Hahn+Kolb Werkzeuge GmbH 1368Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1367_EN_2018_KERN[21850917]-w.indd 1368 12/17/2018 3:35:55 PM Screwdrivers \ Torque screwdriver

Adapter blade for torque screwdrivers no. 52201005-050/52206130-190/52207001-072/52205010-020

Execution: Technical data: . Hexagon mount . Blade diameter: 4 mm Ident. No. 850 Ident. No. 860 . ref. no. 850 output bit holder, 1/4” . ref. no. 860 square drive output, 1/4” Blade length (mm) 162 155 Universal bit Ident. No. 850 52207... holder ● - Adapter blade Ident. No. - 860 52207... ● Prod. Gr. 537 Torque screwdriver Pre-set to ﬁ xed values for TORX screws

Execution: Delivery: . With power grip and fi xed, preset torque calibration certifi cate . fi xed-mounted, non-replaceable 4-mm TX blade . Clearly audible and perceptible engaging when the Technical data: torque is reached . Handle length: 105 mm . Material of the grip handle: 2-component plastic . Not possible to overtighten . Error limit (%): 10 % . Unlimited loosening torque . Calibration certifi cate: Yes

Max. torque measuring range (Nm) 0.6 0.9 1.2 1.4 2 3 Tip size TX6 TX7 TX8 TX9 TX10 TX15 Ident. No. 206 207 208 209 210 215 52208... ● ● ● ● ● ● Prod. Gr. 542

Torque screwdriver TORSIOMAX 775, with calibration certiﬁ cate

Application: . With unlatch coupling, anti-clockwise/clockwise For torque-controlled screw tightening in the CNm tightening range. . Comes with certiﬁ cate

Execution: Technical data: . ¼-inch internal hexagon (F 6.3 DIN 3126) . Blade diameter: 1/4 in . Releases itself . Material of the grip handle: Aluminium . For individual and series tightening . Error limit (%): 6 % . Calibration certiﬁ cate: Yes

Min./max. torque measuring range 0.02-0.3 Nm 0.2-1.2 Nm 0.4-3 Nm 1-5 Nm Scale value (nm) 0.002 0.01 0.01 0.025 Handle length (mm) 105 157 160 205 Ident. No. 010 020 025 030 52208... ● ● ● ● Prod. Gr. 531 Torque screwdriver With calibration certiﬁ cate in line with DIN EN ISO 6790

Application: Advantage: For actuating 1/4” bits according to DIN 3126-C 6.3. . A secure stop function prevents accidental value adjustment Execution: Ident. No. 010 Ident. No. 060 . With length and circular scale for simple and Technical data: precise adjustment . Blade diameter: 1/4 in . When the set value is reached, the mechanism . Material of the grip handle: 1-component plastic slides down so that the values are not overrun . Error limit (%): 6 % . Precision circulation ball coupling for controlled . Calibration certiﬁ cate: Yes clockwise and anti-clockwise tightening Min./max. torque measuring range 0.24-1.2 Nm 1.2-6 Nm Scale value (nm) 0.01 0.1 Handle length (mm) 183 196 Ident. No. 010 060 52204... ● ● Prod. Gr. 556

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1369 Availability subject to country specific rules and regulations.

1369_EN_2018_KERN[21850920]-r.indd 1369 12/17/2018 3:35:56 PM Screwdrivers \ Torque screwdriver

PGNP torque screwdriver with 1/4 inch chuck Adjustable. With calibration certiﬁ cate in line with DIN EN ISO 6789

Execution: . Ident. No. 120–130: With additional plug-in . Calibrated to a permissible deviation of +/- 6% from T-handle in scope of delivery – for high torques the set value. . Precision circulation ball coupling for controlled Technical data: clockwise and anti-clockwise tightening . Handle length: 140 mm . Material of the grip handle: 2-component plastic . Ergonomically shaped 2-component handle . Error limit (%): 6 % . Adjustment tool included with scope of delivery. . Calibration certiﬁ cate: Yes . A suitable tester is required for adjustment Min./max. torque measuring range 0.05-0.25 Nm 0.2-1.5 Nm 0.5-4.5 Nm 2.5-13.5 Nm Ident. No. 100 110 120 130 52204... ● ● ● ● Prod. Gr. 556 Torque screwdriver TORSIOMETER 760

Application: Technical data: For tools with hexagonal shank (E 6.3 DIN 3126). . Handle length: 185 mm . Material of the grip handle: 1-component plastic Execution: . Error limit (%): 4 % . with ¼” hexagon socket chuck (F 6.3 DIN 3126) . Calibration certiﬁ cate: Yes . With comparison scale in.lb and sliding tab . with trailing pointer as indicator function (non-triggering)

Min./max. torque measuring range 0.15-0.75 Nm 0.3-1.5 Nm 0.6-3 Nm 1.2-6 Nm Scale value (nm) 0.025 0.05 0.10 0.20 Ident. No. 206 212 225 250 52205... ● ● ● ● Prod. Gr. 531 1/4” hexagon head to 1/4” square drive connector

Application: Execution: For torque screwdrivers . ¼-inch external hexagon on ¼-inch external square

Drive 1/4 inch Tip size 1/4 inch Length (mm) 50 Ident. No. 300 52205... ● Prod. Gr. 531

STURTEVANT RICHMONT torque screwdrivers For bits with 1/4 inch hexagon insert bit (F 6.3 DIN 3126)

Application: Delivery: Suitable for anti-clockwise and clockwise rotation. Ident. No. 040: Incl. calibration certiﬁ cate Ident. No. 030–035 Execution: Technical data: . Automatic perceptible and audible release . Blade diameter: 1/4 in Ident. No. 040 . Ident. No. 030–035: . Material of the grip handle: 1-component plastic . Torque adjusted using tester . Error limit (%): 6 % . Calibration = price group N . Calibration certiﬁ cate: Yes . Ident. No. 040: . Torque set via Vernier (micrometre scale) . Also available with no scale

Min./max. torque measuring range 0.14-0.7 Nm 0.34-1.7 Nm 0.8-4 Nm Scale value (nm) - - 0.2 Handle length (mm) 140 159 197 Ident. No. 030 035 040 52220... ● ● ● Prod. Gr. 536

Source: Hahn+Kolb Werkzeuge GmbH 1370Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1369_EN_2018_KERN[21850920]-r.indd 1370 12/17/2018 3:35:58 PM Screwdrivers \ Torque screwdriver

STURTEVANT RICHMONT torque screwdriver set For bits with ¼-inch hexagon head (F 6.3 DIN 3126)

Application: . Torque adjusted using tester Suitable for anti-clockwise and clockwise rotation. Delivery: Execution: Incl. calibration certifi cate . Automatic perceptible and audible release Min./max. torque measuring range 0.8-4 Nm Scale value (nm) 0.2 Supplied blade widths: 3 mm/4 mm/5.5 Composition of set mm/8 mm/10 mm Tip size PH0 | PH1 | PH2 | PH3 | PZ1 | PZ2 | TX10 | TX15 | TX20 | TX25 | TX30 | TX40 Blade length (mm) 25 Handle length (mm) 197 Material of the grip handle 1-component plastic Width across fl ats 2.5 mm | 3 mm | 4 mm | 5 mm | 6 mm Error limit (%) (%) 6 Calibration certifi cate Yes Ident. No. 200 52220... ● Prod. Gr. 536 TorqueFix-Key torque screwdriver

Application: . Specially developed for hard-to-reach screws and For controlled bolting at a specifi ed torque and in for confi ned areas confi ned spaces. . Clearly audible and perceptible click signal ensures reliable process Execution: . Fixed preset torque Delivery: . Automatic release In practical plastic box, incl. plant test certifi cate . Compatible with all torque interchangeable blades . Opening torque approx. 30% higher than tightening Technical data: . Material of the grip handle: 1-component plastic torque . Error limit (%): 6 % Advantage: . Calibration certifi cate: Yes . Extremely handy and ergonomic wrench handle thanks to compact design Max. torque measuring range (Nm) 0.9 1.2 2.0 2.5 3.0 4.0 Ident. No. 009 012 020 025 030 040 52221... ● ● ● ● ● ● Prod. Gr. 537

TorqueFix-Key TX and IP blades

Execution: Advantage: . Premium chrome-vanadium-molybdenum steel . Extremely slim blade diameter for diﬃ cult-to-reach . Continuously hardened areas Ident. No. 106–125 . Titanium-silver Technical data: . Blade length: 75 mm . Blade diameter: 4 mm Ident. No. 206–225

Tip size TX6 TX7 TX8 TX9 TX10 TX15 TX20 For Ident. No. 106 107 108 109 110 115 120 52221... TORX®screws ● ● ● ● ● ● ● For TORX®- 52221... Plus screws Ident. No. ------Tip size TX25 TXP6 TXP7 TXP8 TXP9 TXP10 TXP15 For Ident. No. 125 52221... TORX®screws ● ------For TORX®- 206 207 208 209 210 215 52221... Plus screws Ident. No. - ● ● ● ● ● ● Tip size TXP20 TXP25 For 52221... TORX®screws Ident. No. - - For TORX®- 220 225 52221... Plus screws Ident. No. ● ● Prod. Gr. 537

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1371 Availability subject to country specific rules and regulations.

1371_EN_2018_KERN[21850923]-t.indd 1371 12/17/2018 3:35:57 PM Screwdrivers \ Torque screwdriver

TorqueFix-Key blade, hexagon socket

Application: Advantage: For screwing hexagonal screws in conjunction with . Extremely slim blade diameter for diﬃ cult-to-reach TorqueFix-Key torque screwdriver areas

Execution: Technical data: . Premium chrome-vanadium-molybdenum steel . Blade length: 75 mm . Continuously hardened . Blade diameter: 4 mm . Titanium-silver Width across ﬂ ats 1.5 mm 2 mm 2.5 mm 3 mm 4 mm Ident. No. 315 320 325 330 340 52221... ● ● ● ● ● Prod. Gr. 537

Torque screwdriver with T-handle Wiha TorqueVario®-STplus with scale, with calibration certiﬁ cate

Execution: . Automatic release and click signal when the set . Numerical torque value gauge in scale window torque is reached . Torque can be continuously adjusted from 5 to 14 . Complete with adjustment tool Nm using an adjustment tool Delivery: . Comfortable T-handle with so area for optimum With adjustment tool, in practical plastic box torque transmission Blade Ø (mm) 6 Material of the grip handle 2-component plastic Error limit (%) (%) 6 Calibration certiﬁ cate Yes Ident. No. 010 52222... ● Prod. Gr. 537

Torque screwdriver set with T-handle Wiha TorqueVario®-STplus with scale, with calibration certiﬁ cate

Execution: . Set of 1/4” and 3/8” adapter blades and bit . Numerical torque value gauge in scale window holders, bits and setting tool . Torque can be continuously adjusted from 5 to 14 Delivery: Nm using an adjustment tool Torque screwdriver no. 52222 010, universal bit . Comfortable T-handle with so area for optimum holder, 2 adapter blades for ¼-inch and 3/8-inch torque transmission nuts, setting tool . Automatic release and click signal when the set torque is reached Min./max. torque measuring range 5-14 Nm Tip size 1/4 inch | TX25 | TX30 | TX40 Error limit (%) (%) 6 Blade Ø (mm) 6 Width across ﬂ ats 4 mm | 5 mm | 6 mm Material of the grip handle 2-component plastic Calibration certiﬁ cate Yes Ident. No. 090 52222... ● Prod. Gr. 537 Blades for torque screwdrivers with t-handle TORX and TORX plus

Technical data: . Blade length: 130 mm . Blade diameter: 6 mm Ident. No. 215–240

Ident. No. 315–340 Tip size TX15 TX20 TX25 TX27 TX30 TX40 TXP15 TXP20 TXP25 TXP27 TXP30 TXP40 For 215 220 225 227 230 240 52222... TORX® Ident. No. ● ● ● ● ● ● ------screws For TORX®- 315 320 325 327 330 340 52222... Plus Ident. No. ------● ● ● ● ● ● screws

Prod. Gr. 537

Source: Hahn+Kolb Werkzeuge GmbH 1372Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1371_EN_2018_KERN[21850923]-t.indd 1372 12/17/2018 3:36:00 PM Screwdrivers \ Torque screwdriver

Blades for torque screwdrivers with t-handle For hexagon socket

Technical data: . Blade length: 130 mm . Blade diameter: 6 mm

Width across ﬂ ats 3 mm 4 mm 5 mm 6 mm Ident. No. 403 404 405 406 52222... ● ● ● ● Prod. Gr. 537

Blades for torque screwdrivers with t-handle Adapters and bit holders

Technical data: . Blade diameter: 6 mm Ident. No. 440 Ident. No. 450–460 Tip size 1/4 inch 1/4 inch 3/8 inch Blade length (mm) 125 120 120 Ident. No. 440 450 460 52222... ● ● ● Prod. Gr. 537

Torque wrenches with T-handle DREMOMETER T-FS, with DIN EN ISO 6789 calibration certiﬁ cate

Execution: Notes: . Torque is fi xed, for controlled tightening in a clock- Torque range 1 to 5 Nm on request. wise direction . High-quality, aluminium alloy handle housing, Technical data: robust and durable . Tip size: 1/4 inch . Automatic quick release with perceptible and . Material of the grip handle: 1-component plastic audible signal . Error limit (%): 6 % . Calibration certifi cate: Yes . Weighs only 241 g Delivery: In plastic box, with calibration certifi cate Max. torque measuring range (Nm) 6 7 8 9 10 11 12 Ident. No. 006 007 008 009 010 011 012 52223... ● ● ○ ○ ● ○ ○ Prod. Gr. 556

Kra form Kompakt VDE torque screwdriver Adjustable. Set with interchangeable blades

Execution: Technical data: . Torque holder can be adjusted from 1.2 to 3.0 Nm . Min./max. torque measuring range: 1.2-3.0 Nm without tools . Scale value: 0.1 . Kra form Plus handle with high torque . Composition of set: slot widths supplied: transmission 2.5/3.5/4.0/5.5 mm . Tip size: PH1 PH2 PZ1 PZ2 PZ1 + slot PZ2 . clear audible and haptic engage when the set value | | | | | + slot TX10 TX15 TX20 TX25 is reached | | | | . Blade length: 154 mm . insulated interchangeable blades lock into the . Handle length: 192 mm handle . Material of the grip handle: 2-component plastic . Error limit (%): 6 % Delivery: . Calibration certifi cate: Yes calibration certifi cate . VDE certifi ed: Yes

Ident. No. 400 52208... ● Prod. Gr. 542

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1373 Availability subject to country specific rules and regulations.

1371_EN_2018_KERN[21850923]-t.indd 1373 12/17/2018 3:36:03 PM Screwdrivers \ Torque wrench

Torque wrench with ratchet With calibration certiﬁ cate according to DIN EN ISO 6789

Execution: Advantage: . The torque is set by turning the handle . Robust tubular design . With lever ratchet, suitable only for controlled . Reversible ratchet with locking push button Ident. No. 060 clockwise tightening. . Viewing window protects scale from damage . Haptic and acoustic adjustment aid . Audible and perceptible release when the set value Delivery: Secure and safe transport/storage in handy cylindri- is reached cal package . Dual scale with Nm and lbf. . display . Ergonomically shaped handle with comfortable, Technical data: textured surface . With scale: Yes . Rapid securing and opening via the locking ring Tip size 1/4 inch 1/4 inch 3/8 inch 1/2 inch 1/2 inch 1/2 inch Min./max. torque measuring range 1-6 Nm 2.5-25 Nm 10-60 Nm 20-120 Nm 40-200 Nm 60-320 Nm Scale value (nm) 0.1 0.25 0.5 1 1 2 Length (mm) 234 274 355 456 551 621 Error limit (%) (%) 4 3 3 3 3 3 Ident. No. 006 025 060 120 200 320 52240... ● ● ● ● ● ● Prod. Gr. 5HC Torque wrench with square head With calibration certiﬁ cate in line with DIN EN ISO 6789

Execution: . Rapid securing and opening via the locking ring . Adjustable torque wrench Advantage: . For holding square plug-in tools . Robust tubular design Ident. No. 120 . Haptic and acoustic adjustment aid . Plug-in square with locking push button . Audible and perceptible release when the set value . Viewing window protects scale from damage is reached . Dual scale with Nm and lbf. . display Technical data: . Ergonomically shaped handle with comfortable, . Error limit (%): 3 % textured surface . With scale: Yes

Min./max. torque measuring range 2.5-25 Nm 10-60 Nm 20-120 Nm 40-200 Nm 60-320 Nm Scale value (nm) 0.25 0.5 1 1 2 Insert shank square 9 x 12 mm 9 x 12 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm Length (mm) 258 312 393 488 558 Ident. No. 025 060 120 200 320 52241... ● ● ● ● ● Prod. Gr. 5HC Torque wrench With break-over mechanism

Application: Advantage: Suitable for clockwise and anti-clockwise tightening; . The break-over release mechanism makes unin- 1 2 3 when the pre-set torque value is reached, the tended overtightening unlikely wrench clearly and perceptibly releases and can be 20° instantly used. Delivery: 1 Incl. adjustment tool, test certiﬁ cate according to Execution: DIN EN 6790 . Lockable torque wrench without scale . The torque is adjusted using a torque wrench tester Technical data: . Permanent adjustment can be performed in-house . Insert shank square: 9 x 12 mm by us (if required, specify the Nm value when . Length: 105 mm placing your order), or by the customer using a . Error limit (%): 6 % . suitable tester With scale: No

Min./max. torque measuring range 0.4-2 Nm 1-10 Nm Ident. No. 110 120 52243... ● ● Prod. Gr. 5HC

Source: Hahn+Kolb Werkzeuge GmbH 1374Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1374_EN_2018_KERN[21850927]-u.indd 1374 12/17/2018 3:35:56 PM Screwdrivers \ Torque wrench

Torque wrench Safety clutch

Application: . Ident. No. 310–320: For controlled clockwise tightening; when the pre-set torque value is reached, . Easy-to-read micrometre scale for making adjustments, can be secured the wrench releases and can be instantly used. against unintentional changes . With integrated ratchet function for controlled clockwise rotation Execution: . High-quality, single-armed torque wrench without scale Advantage: . High-alloy, stainless steel head . The patented release system reliably prevents unwanted overtightening of the screw connection . Anodised aluminium shank . Ident. No. 010–220: Delivery: . The torque is adjusted using a torque wrench tester Ident. No. 010–220: Incl. adjustment tool . Permanent adjustment can be performed in-house by us (if required, specify the Nm value when placing your order), or by the customer using a suitable tester

Ident. No. 010–040

Ident. No. 210–220 Ident. No. 310–320

Tip size 1/4 inch 3/8 inch 1/2 inch 1/4 inch 1/4 inch 1/4 inch 1/4 inch Min./max. torque measuring range 3-25 Nm 15-55 Nm 40-125 Nm 1-5 Nm 2-10 Nm 1-5 Nm 2-10 Nm Length (mm) 216 324 460 185 185 195 195 With scale No No No No No Yes Yes Error limit (%) (%) 4 4 4 6 6 6 6 Ident. No. 010 030 040 210 220 310 320 52243... ● ● ● ● ● ● ● Prod. Gr. 5HC

ARE YOU LOOKING FOR PRODUCTS THAT MEET THE TOUGHEST DEMANDS?

WE HAVE WHAT IT TAKES.

For a complete range of products that meet the toughest demands, visit www.iconridge.com

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1375 Availability subject to country specific rules and regulations.

1374_EN_2018_KERN[21850927]-u.indd 1375 12/17/2018 3:35:59 PM Screwdrivers \ Torque wrench

DREMASTER UK torque wrench with reversible ratchet With calibration certiﬁ cate according to DIN EN ISO 6789

Execution: . A jump system generates a perceptible and audible . Classifi ed according to DIN EN ISO 6789:2003 type release signal II class A, with traceable workshop certifi cate . Ergonomic system for torque adjustment with note . With ½-inch reversible ratchet symbol . Robust, satin-fi nish chrome-plated tubular steel . Secured adjusting-tuning system structure, with chrome-plated ratchet . Ergonomically shaped 2-component plastic handle Technical data: with calibration aid . Tip size: 1/2 inch . With scale: Yes . Switching between main scale Nm and auxiliary . Error limit (%): 3 % s c a l e l b f - . With micrometer scale for Nm main scale for adjustment of scale intermediate values Min./max. torque measuring range 20-100 Nm 40-200 Nm 60-300 Nm Scale value (nm) 0.5 1 1 Length (mm) 438 529 620 Ident. No. 015 030 045 52242... ● ● ● Prod. Gr. 556

DREMASTER K torque wrench with reversible square With calibration certiﬁ cate according to DIN EN ISO 6789

Application: Advantage: For right and le -handed operation by re-ﬁ tting the . Setting using insertion button in handle end square drive . Micrometre scale graduation on the handle enables extremely precise adjustment of the torque Ident. No. 111–131 Execution: . The torque is set by turning the handle Technical data: . Easy-to-read scale protected by magniﬁ ed trans- . With scale: Yes parent screen . Error limit (%): 3 % . Self-releasing with easily audible and perceptible signal Tip size 1/2 inch 1/2 inch 1/2 inch 3/4 inch 3/4 inch Min./max. torque measuring range 20-100 Nm 40-200 Nm 60-300 Nm 80-400 Nm 150-750 Nm Scale value (nm) 0.5 1 1 1 1 Length (mm) 423 514 606 715 1228 Ident. No. 111 121 131 141 161 52242... ● ● ● ● ● Prod. Gr. 556

DREMASTER SE torque wrench with square key With calibration certiﬁ cate in line with DIN EN ISO 6789

Execution: . A jump system generates a perceptible and audible . Classifi ed according to DIN EN ISO 6789:2003 type release signal II class A, with traceable workshop certifi cate . Ergonomic system for torque adjustment with note . Robust, satin-fi nish chrome-plated tubular steel symbol structure, with chrome-plated rectangular mount . Secured adjusting-tuning system . Ergonomically shaped 2-component plastic handle with calibration aid Technical data: . Switching between main scale Nm and auxiliary . Error limit (%): 3 % s c a l e l b f - . With scale: Yes . With micrometer scale for Nm main scale for adjustment of scale intermediate values Min./max. torque measuring range 20-100 Nm 40-200 Nm 60-300 Nm Scale value (nm) 0.5 1 1 Insert shank square 9 x 12 mm 14 x 18 mm 14 x 18 mm Length (mm) 399 500 591 Ident. No. 220 240 260 52242... ● ● ● Prod. Gr. 556

Source: Hahn+Kolb Werkzeuge GmbH 1376Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1374_EN_2018_KERN[21850927]-u.indd 1376 12/17/2018 3:36:00 PM Screwdrivers \ Torque wrench

TORCOFIX torque wrench with reversible square With calibration certiﬁ cate according to DIN EN ISO 6789

Application: . Dual scale of Nm and lbf- underneath a magniﬁ ed For right and le -handed operation by re-ﬁ tting the transparent screen square drive . A jump system generates a perceptible and audible release signal Execution: . Locking button integrated in the handle Ident. No. 100 . Adjustable and robust pipe torque wrench with release button Technical data: . Integrated ratchet . With scale: Yes . Matt chrome-plated steel pipe design with chrome- . Error limit (%): 3 % plated ratchet

Tip size 1/4 inch 1/4 inch 3/8 inch 1/2 inch 1/2 inch 1/2 inch 3/4 inch 3/4 inch Min./max. torque measuring range 1-5 Nm 5-25 Nm 10-50 Nm 20-100 Nm 40-200 Nm 60-300 Nm 80-400 Nm 110-550 Nm Scale value (nm) 0.025 0.1 0.25 0.5 1 1 1 1 Length (mm) 224 285 335 394 485 577 686 957 Ident. No. 005 025 050 100 200 300 400 550 52246... ● ● ● ● ● ● ● ● Tip size 3/4 inch 3/4 inch Min./max. torque measuring range 150-750 Nm 250-850 Nm Scale value (nm) 1 1 Length (mm) 1236 1379 Ident. No. 750 850 52246... ○ ○ Prod. Gr. 556

JETCO torque screwdrivers with dial gauge, trailing pointer and calibration certiﬁ cate

Execution: Advantage: . large, reﬂ ection-free scale window allows for . simple, fast handling accurate and fast reading . robust design with strengthened scale housing Delivery: in a rugged plastic case . ergonomic handle . measurements can be taken regardless of force Technical data: Ident. No. 300 application point . Error limit (%): 4 % . for right- and le -handed operation, with rigid square output

Ident. No. 340

Min./max. torque measuring range 1.2-6 Nm 3-15 Nm 10-50 Nm 20-100 Nm 40-200 Nm 80-400 Nm Scale value (nm) 0.1 0.5 1 2 5 10 Tip size 1/4 inch 1/4 inch 3/8 inch 1/2 inch 1/2 inch 1/2 inch Length (mm) 270 270 270 559 559 559 Ident. No. 300 310 320 330 340 350 52245... ● ● ● ● ● ● Prod. Gr. 531

Torque wrench With trailing pointer and calibration certiﬁ cate in line with DIN EN ISO 6789

Execution: Delivery: . Indicative torque wrench with dial gauge and In robust plastic box multi-functional maximum indicator with double square and integrated ratchet function on both Notes: sides Other sizes on request. . Non-slip rubber handle Technical data: . Error limit (%): 4 % Min./max. torque measuring range 0.8-4 Nm 2.4-12 Nm 5-25 Nm 8-40 Nm 16-80 Nm 40-200 Nm Scale value (nm) 0.1 0.5 1 1 2 5 Tip size 1/4 inch 1/4 inch 3/8 inch 3/8 inch 1/2 inch 1/2 inch Length (mm) 244 244 244 244 435 515 Ident. No. 010 020 030 040 050 060 52247... ● ● ● ● ● ● Prod. Gr. 556

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1377 Availability subject to country specific rules and regulations.

1377_EN_2018_KERN[21850932]-q.indd 1377 12/17/2018 3:35:56 PM Screwdrivers \ Torque wrench

DREMOMETER torque wrench With calibration certiﬁ cate according to DIN EN ISO 6789

Application: Advantage: The tightening value is set and read from the scale by means of rotary motion . Special design ensures faultless operation with angle key integrated in the handle end. . The measured value or set torque is not changed Execution: . Independent of handle position . Audible and perceptible release when the tightening torque is reached Technical data: . Single key, one arm, with automatic release . Error limit (%): 3 %

Ident. No. 008–035 Ident. No. 006 Ident. No. 040–060

Min./max. torque measuring range 2.5-12 Nm 6-30 Nm 8-40 Nm 25-120 Nm 40-200 Nm 60-300 Nm 80-360 Nm 110-550 Nm Scale value (nm) 0.5 1 5 5 5 5 5 10 Tip size 1/4 inch 1/4 inch 3/8 inch 1/2 inch 1/2 inch 1/2 inch 3/4 inch 3/4 inch Length (mm) 211 268 338 462 551 617 717 812 Min./max. length ------Ident. No. 006 008 010 020 025 028 030 032 52248... ● ● ● ● ● ● ● ● Min./max. torque measuring range 155-760 Nm 155-760 Nm 520-1000 Nm 750-2000 Nm Scale value (nm) 10 10 10 50 Tip size 3/4 inch 3/4 inch 3/4 inch 1 inch Length (mm) 812 - - - Min./max. length - 812-1413 mm 812-1413 mm 932-2008 mm Ident. No. 035 040 050 060 52248... ● ● ● ● Prod. Gr. 556

Angle of rotation measuring instrument For torque screwdriver

Application: For mounting on ½-square of torque wrench for angle-controlled tightening of screws in a single step.

Drive 1/2 inch Tip size 1/2 inch Angle (Degree) 360 Ident. No. 100 52248... ● Prod. Gr. 556

STURTEVANT RICHMONT signal torque wrench

Application: . locking mechanics prevents accidental torque for replaceable plug-in tools no. 52250-52256. adjustment . indestructible metal handle with knurling and Execution: middle ring. . haptic and audible “click” and brief loose run indi- cate that the set torque has been reached Technical data: . calibration certiﬁ cate . With scale: Yes . release mechanism can be adjusted using the . Adapter type: Dove tail precision adjustment scale on the handle . Error limit (%): 4 %

Min./max. torque measuring range 1.2-6 Nm 4-20 Nm 20-100 Nm 40-200 Nm Scale value (nm) 0.1 0.2 0.5 1.0 Length (mm) 229 229 329 413 Ident. No. 091 101 111 121 52249... ● ● ● ● Prod. Gr. 536

Source: Hahn+Kolb Werkzeuge GmbH 1378Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1377_EN_2018_KERN[21850932]-q.indd 1378 12/17/2018 3:35:58 PM Screwdrivers \ Torque wrench

STURTEVANT RICHMONT plug-in tool Box wrenches

Application: . Material: Tool steel For signal torque screwdriver no. 52249 090-250 . Dimension A: 56.4 mm . Dimension B: 39.7 Technical data: . Dimension C: 18.3 mm . Width across ﬂ ats: 27 mm . Dimension D: 31.8 mm . Max. load force: 350 N . Dimension E: 23.8 mm . Surface: Burnished

Ident. No. 270 52251... ● Prod. Gr. 536

Click torque wrench with ratchet with calibration certiﬁ cate, for clockwise tightening

Execution: . locking button on the end of the handle with silicone padding — protection . setting: audible and perceptible click when scale values are reached against unintentional adjustment . release mechanism: audible and perceptible click signal when the set torque . Ident. No. 200, 220–280: very robust design, with ratchet (45 teeth) is reached . Ident. No. 210: very robust design, with ratchet (45 teeth) — with direct . dual Nm and lbf- scale mounting of bits . ﬁ ne adjustment scale in Nm — ensures precise and safe operation Delivery: . ergonomically shaped 2-component handle in a robust plastic rot. box

Ident. No. 270 Ident. No. 200

Tip size 1/4 inch 1/4 inch 3/8 inch 3/8 inch 1/2 inch 1/2 inch 1/2 inch 1/2 inch Min./max. torque measuring range 2.5-25 Nm 2.5-25 Nm 10-50 Nm 20-100 Nm 10-50 Nm 20-100 Nm 40-200 Nm 60-300 Nm Scale value (nm) 0.10 0.10 0.25 0.50 0.25 0.50 1.00 1.00 Length (mm) 290 291 360 405 360 405 510 595 With scale Yes Yes Yes Yes Yes Yes Yes Yes Error limit (%) (%) 4 4 3 3 3 3 3 3 Ident. No. 200 210 220 230 240 260 270 280 52261... ● ● ● ● ● ● ● ● Prod. Gr. 542

5000-2 CT torque wrench system With reversible ratchet and calibration certiﬁ cate

Execution: Technical data: . Quick and reliable adjustment of the required . With scale: Yes torque by turning the handle . Error limit (%): 4 % . Audible and perceptible quick release Ident. No. 210 . Precise and ﬁ ne scale graduation

Tip size 1/4 inch 3/8 inch 1/2 inch 1/2 inch 1/2 inch Min./max. torque measuring range 2.5-25 Nm 10-60 Nm 20-120 Nm 40-200 Nm 60-320 Nm Scale value (nm) 0.25 0.5 1 1 2 Length (mm) 232 320 408 513 632 Ident. No. 200 210 220 230 240 52262... ● ● ● ● ● Prod. Gr. 569

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1379 Availability subject to country specific rules and regulations.

1379_EN_2018_KERN[21850935]-z.indd 1379 12/17/2018 3:35:57 PM Screwdrivers \ Torque wrench

6000 CT torque wrench system With reversible ratchet and calibration certiﬁ cate

Execution: . Hard chrome-plated, slim steel pipe design Delivery: . Quick and reliable adjustment of the required . Automatic, audible, visible and perceptible quick In storage box torque by turning the handle release . Rotary button provides additional locking function . Ident. No. 001–050: Ref. no. 010, 020, 030, 040, Technical data: for adjustments 050 with signal button . With scale: Yes

Ident. No. 030 Ident. No. 001 Ident. No. 060–100

Tip size 1/4 inch 1/4 inch 1/4 inch 3/8 inch 3/8 inch 1/2 inch 1/2 inch 1/2 inch Min./max. torque measuring range 1-6 Nm 2-10 Nm 4-40 Nm 5-60 Nm 20-120 Nm 20-120 Nm 40-200 Nm 60-320 Nm Scale value (nm) 0.1 0.2 0.4 0.5 1 1 1 2 Length (mm) 197 198 256 335 389 435 543 659 Error limit (%) (%) 4 2 2 2 2 2 2 2 Ident. No. 001 002 004 010 020 030 040 050 52262... ● ● ● ● ● ● ● ● Tip size 3/4 inch 3/4 inch 3/4 inch 3/4 inch 1 inch Min./max. torque measuring range 100-400 Nm 200-500 Nm 300-800 Nm 400-1000 Nm 600-1600 Nm Scale value (nm) 2.5 2.5 2.5 5 5 Length (mm) 803 1040 1280 1788 2455 Error limit (%) (%) 2 2 2 3 3 Ident. No. 060 070 080 090 100 52262... ● ● ● ○ ○ Prod. Gr. 569 5000 CLT torque wrench system With reversible ratchet and calibration certiﬁ cate

Execution: Technical data: . Precisely adjustable and easy-to-read display. . Tip size: 1/2 inch . Scale value: 1 nm . With scale: Yes . Error limit (%): 4 %

Min./max. torque measuring range 20-120 Nm 40-200 Nm 60-320 Nm Length (mm) 435 545 660 Ident. No. 010 020 030 52263... ● ● ● Prod. Gr. 569 6000 CT torque wrench system With calibration certiﬁ cate

Application: Delivery: For holding plug-in tools no. 52286. In safe storage box

Execution: Technical data: . Can be set to micrometre scale by turning the . Error limit (%): 2 % handle . With scale: Yes . Automatic audible, visible and perceptible quick release when the set value is reached . Le and right hand tightening with set torque possible

Min./max. torque measuring range 5-60 Nm 20-120 Nm 40-200 Nm 60-320 Nm Scale value (nm) 0.5 1 1 2 Insert shank square 9 x 12 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm Length (mm) 305 400 510 620 Ident. No. 010 020 030 040 52264... ● ● ● ● Prod. Gr. 569

Source: Hahn+Kolb Werkzeuge GmbH 1380Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1379_EN_2018_KERN[21850935]-z.indd 1380 12/17/2018 3:36:00 PM Screwdrivers \ Torque wrench

6300 CT torque wrench system With calibration certiﬁ cate

Application: . Setting and locking only with combination key For holding plug-in tools no. 52286; only suitable for ident. no. 200 in combination with torque tester right-hand threads. no. 52292

Execution: Technical data: . No adjustment scale . Error limit (%): 2 % . Automatic audible and perceptible quick release . With scale: No

Ident. No. 010

Ident. No. 050

Min./max. torque measuring range 2-12 Nm 2-25 Nm 5-50 Nm 15-35 Nm 15-85 Nm 50-200 Nm 60-320 Nm Insert shank square 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 14 x 18 mm 14 x 18 mm Length (mm) 125 180 240 180 315 400 630 Ident. No. 010 020 040 030 050 060 070 52266... ● ● ● ○ ● ● ● Prod. Gr. 569 Accessories for 52266 020 52266 030 52266 040 52266 050 52266 060 52266 070 Combination key Ident. No. 200 200 200 200 200 200 52266... ● ● ● ● ● ●

VDE torque wrench 5108 VDE and 5109 VDE with calibration certiﬁ cate

Application: Advantage: for working on live components . long service life and precision owing to disas- sembly option – Execution: . Wrench is consequently readjustable and can be . Right/le triggering with 3/8-inch interchangeable recalibrated. square drive Ident. No. 020 . safety owing to quick release (perceptible) and Technical data: acoustic signal (kink element) . Tip size: 3/8 inch . ﬁ ne scale interval with vernier scale . VDE certiﬁ ed: Yes . locking mechanism against unintentional adjustment of setting value Min./max. torque measuring range 2-10 Nm 5-25 Nm Scale value 0.2 0.5 Length (mm) 590 640 Error limit (%) (%) 6 4 Ident. No. 010 020 52268... ● ● Prod. Gr. 569

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1381 Availability subject to country specific rules and regulations.

1381_EN_2018_KERN[21850938]-v.indd 1381 12/17/2018 3:35:55 PM Screwdrivers \ Torque wrench

Torque wrench MANOSKOP® 730 and 730 Quick from 6–50 Nm, all models with calibration certiﬁ cate

Execution: . double stop signal Advantage: . Ident. No. 002–003: . dual scale with Nm and -lb . Ident. No. 002–003: Long-term accuracy . With mount for replaceable plug-in tools . integrated magnifying glass in adjustment . Double stop signal window for optimal legibility Delivery: . Double scale . can be adjusted without dismantling Ident. No. 305–365: in sturdy plastic container . Rapid settings/adjustments . ergonomically shaped, non-slip adjustment . Can be adjusted without dismantling element Technical data: . Ident. No. 305–365: . QuickRelease safety catch on insert head . With scale: Yes . with chuck for replaceable plug-in tools . Low-wear triggering system with bending rod.

Ident. No. 305, 313–365

Ident. No. 002–003

Min./max. torque measuring Scale value (nm) Insert shank square Length (mm) Error limit (%) (%) 52281... range Ident. No. 4-20 Nm 0.5 9 x 12 mm 179 4 002 ● 8-40 Nm 1 9 x 12 mm 222 4 003 ● 6-50 Nm 2 9 x 12 mm 315 3 305 ● 20-100 Nm 2.5 9 x 12 mm 371 3 310 ● 25-130 Nm 2.5 14 x 18 mm 406 3 313 ● 40-200 Nm 5 14 x 18 mm 452 3 320 ● 80-400 Nm 10 14 x 18 mm 592 3 340 ● 130-650 Nm 20 14 x 18 mm 874 3 365 ● Prod. Gr. 531

Torque wrench MANOSKOP® 730 Fix, with calibration certiﬁ cate

Application: . two-component handle made from extremely ﬁ xed tightening torque for increased safety in series resistant plastic use . ergonomically shaped, non-slip adjustment element Execution: . QuickRelease safety catch on insert head . chuck for exchangeable plug-in tools . low-wear triggering system with bending rod. . double stop signal . dual scale showing Nm and -lb Technical data: . adjustment head can be unscrewed a er adjusting . Error limit (%): 3 % the release torque . With scale: Yes

Min./max. torque measuring range Scale value (nm) Insert shank square Length (mm) 52281... Ident. No. 10-50 Nm 2 9 x 12 mm 315 405 ● 20-100 Nm 2.5 9 x 12 mm 370 410 ● 25-130 Nm 2.5 14 x 18 mm 410 413 ● 40-200 Nm 5 14 x 18 mm 455 420 ● 80-400 Nm 10 14 x 18 mm 592 440 ● 130-650 Nm 20 14 x 18 mm 875 465 ● Prod. Gr. 531

Torque wrench Service MANOSKOP® 730 N with calibration certiﬁ cate

Execution: Advantage: . With mount for replaceable plug-in tools . Quick and precise adjustment . Double stop signal . Double scale Technical data: . Error limit (%): 3 % . Ergonomic 2-component handle . With scale: Yes Min./max. torque measuring range 4-20 Nm 10-50 Nm 20-100 Nm 25-130 Nm 40-200 Nm 80-400 Nm 130-650 Nm Scale value (nm) 0.2 0.25 0.5 0.5 1 2 2.5 Insert shank square 9 x 12 mm 9 x 12 mm 9 x 12 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm Length (mm) 275 330 386 421 467 607 890 Ident. No. 004 005 010 012 020 040 065 52282... ● ● ● ● ● ● ● Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH 1382Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1381_EN_2018_KERN[21850938]-v.indd 1382 12/17/2018 3:35:58 PM Screwdrivers \ Torque wrench

Torque wrench MANOSKOP® 755 series

Application: Advantage: For holding plug-in tools no. 52286, suitable for . Long-term accuracy working on production lines or for series production work. Technical data: . Error limit (%): 4 % Execution: . With scale: No . Double stop signal . No adjustment scale, adjustment via testers . Automatic audible and perceptible release when the set value is reached . Made from square steep pipe

Min./max. torque measuring range 4-40 Nm 20-100 Nm 40-200 Nm 60-300 Nm Insert shank square 9 x 12 mm 9 x 12 mm 14 x 18 mm 14 x 18 mm Length (mm) 201 318 457 609 Ident. No. 090 100 110 120 52284... ● ● ● ● Prod. Gr. 531

VDE torque wrenches with ratchet MANOSKOP 730 VDE, with calibration certiﬁ cate

Application: . low-wear triggering system with bending rod for working on live components . both types are supplied complete with 3/8-inch plug-in reversible ratchets. Execution: . proven QuickSelect quick torque adjustment Technical data: . additional graduated dial for precise adjustment . Insert shank square: 9 x 12 mm . Interchangeable plug-in ratchet included, 3/8-inch . Error limit (%): 3 % output . With scale: Yes . clockwise and counter-clockwise tightening, QuickRelease safety lock Min./max. torque measuring range 4-25 Nm 10-50 Nm Scale value (nm) 0.2 0.25 Length (mm) 370 425 Ident. No. 001 002 52285... ● ● Prod. Gr. 531

Electronic torque wrench SENSOTOK 701 with built-in 1/4” ﬁ ne-tooth ratchet

Execution: Advantage: . very slim and compact design for torques from 1 . versatile – 3 measuring modes: Track, Peak Hold, Nm screwing application with evaluation . measurement units: Nm, cNm, -lb and in-lb . intuitive keying-in control ensures simple . measurements can be taken regardless of force adjustment application point . ergonomic handle construction for eﬀ ortless . With 3.6 V lithium battery (spare battery art no. operation 56815330) . with certiﬁ cate Technical data: . Min./max. torque measuring range: 1-20 Nm . evaluation of screwing process by means of colour . Tip size: 1/4 inch LEDs, buzzer and vibration . Length: 210 mm . Error limit (%): 4 %

Ident. No. 200 52284... ● Prod. Gr. 531 Accessories for 52284 200 56815... Round cells/special Ident. No. 330 battery Price/unit, € -

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1383 Availability subject to country specific rules and regulations.

1383_EN_2018_KERN[21850941]-12.indd 1383 12/17/2018 3:35:56 PM Screwdrivers \ Torque wrench

Electronic torque/angle-controlled wrenches Sensotork® 713 R with digital display and calibration certiﬁ cate

Execution: . backlighting of the display (traﬃ c light principle) . Electronic torque wrenches for rotation angle with screwdriving processes are saved with a time plug-in tool reversible ratchet stamp

1 2 3 4 5 . With quick-release safety locking device Advantage: . Torque and rotating angle are visible simultane- . Service friendly thanks to simple adjustment and ① ously, comfortable rotating angle measurement self-actuated note regarding next calibration without reference arm in extremely large area of deadline rotation. . Individual identifi cation designation possible, . Measurement units: Nm, .lb, in.lb protection against unintentional adjustment and . Adjustable pre-warning time of visual, perceptible external access by password and acoustic signals . Repeated screw tasks can be combined into a . Adjustable individual plug-in tool lengths menu-controlled process . Fulfi ls DKD-R3-7, Class 2 and DIN EN ISO 6789, with certifi cate Delivery: In a rugged plastic case incl. batteries (2x Mignon . operating duration approx. 60 hours (with 2 1.5 V, type AA) batteries type Mignon, 1.5 V, AA) . Measurements can be taken regardless of force application point Technical data: . Error limit (%): 1 %

Min./max. torque measuring range 3-60 Nm 10-200 Nm 20-400 Nm Tip size 3/8 inch 1/2 inch 3/4 inch Insert shank square 9 x 12 mm 14 x 18 mm 14 x 18 mm Length (mm) 378 608 838 Ident. No. 100 102 104 52282... ● ● ● Prod. Gr. 531

Electro-mechanical torque/angle-controlled wrench MANOSKOP 714 – indicating and cut-out

Execution: . Display resolution, rotation angle 0.1° . 4 measurement modes (torque, rotation angle, . Torque display resolution <= 60 Nm: 0.01 Nm > 60 torque with control variable of rotation angle, rota- Nm: 0.1 Nm tion angle with control variable of torque) Advantage: . High-resolution colour graphic display with addi- Ident. No. 001–010, 040 tional lateral signal lights, freely conﬁ gurable menu . Quick and precise setting via keyboard, automatic structure key lock to protect against accidental changes to settings . 3 function modes: triggering, peak (displaying . Overload protection by means of acoustic and operation with peak value display) and track Ident. No. 020 (displaying operation with current value display) optical warning signals and forced release (right) . Micro-USB 2.0 interface . Reliable handling with ergonomically shaped handle (resistant to oils, greases, fuels, brake . Data storage (2500 screwdriving processes), up ﬂ uids and Skydrol) to 200 screw joints in max. 25 processes can be programmed Delivery: . Measurement units: Nm, .lb, in.lb/automatically In robust plastic case (size 40 in sheet steel case), correct tightening torque on input of deviating with so ware Sensomaster, USB cable, 4 micro bat- actual dimension teries AAA/LR03, 1.5 V micro NiMh batteries AAA, . Feelable, optical and acoustic release signal, 1.2 V can be used. torque and angle of rotation visible simultaneously . Automatic indication of the next calibration Technical data: deadline depending on the time and/or the loading . Error limit (%): 2 % count Min./max. torque measuring range 1-10 Nm 2-20 Nm 4-40 Nm 6-60 Nm 10-100 Nm 20-200 Nm 40-400 Nm Insert shank square 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 14 x 18 mm 14 x 18 mm Length (mm) 226 226 252 393 466 547 656 Ident. No. 001 002 004 006 010 020 040 52283... ● ● ● ● ● ● ○ Prod. Gr. 531 Accessories for 52283 001 52283 002 52283 004 52283 006 52283 010 52283 020 52283 040 Li-ion battery Ident. No. 100 100 100 100 100 100 100 52283... ● ● ● ● ● ● ● Charger Ident. No. 110 110 110 110 110 110 110 52283... ● ● ● ● ● ● ●

Source: Hahn+Kolb Werkzeuge GmbH 1384Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1383_EN_2018_KERN[21850941]-12.indd 1384 12/17/2018 3:35:59 PM Screwdrivers \ Torque wrench

Electro-mechanical torque wrench Service/series MANOSKOP® 730 D with calibration certiﬁ cate

Execution: Advantage: . Display and release when the set torque is reached . Quick setting via handy keyboard and large display 1 2 3 4 5 just like a mechanical wrench . Automatic key lock to protect against accidental . Holder for plug-in tools changes to settings, protection against setting ① . Display of the value reached on the display changes by third parties via PIN code. . In ‘display’ mode, continuous display of torque . Overloading protection by means of acoustic and experienced on display optical warning signals . Saved values of screw-tightening actions can be Delivery: transferred to a PC (USB interface, storage of up to In robust plastic case 7500 screw-tightening actions in wrench) . Automatic indication of the next calibration dead- Technical data: line (convenient adherence to DIN EN ISO 6789) . Error limit (%): 2 % . Operating duration approx. 60 hours (with 2 batteries type Mignon, 1.5 V, AA) Min./max. torque measuring range 10-100 Nm 20-200 Nm 40-400 Nm Insert shank square 9 x 12 mm 14 x 18 mm 14 x 18 mm Length (mm) 467 548 688 Ident. No. 410 420 440 52282... ● ● ● Prod. Gr. 531 USB adapter, cable, so ware and rotation angle module for Manoskop 730 D

Application: . With jack plug cable to connect to the key data output Ident. No. 500: For electro-mechanical torque wrenches, for documenting and managing measured values on a PC. Advantage: Ident. No. 601: For mounting on electromechanical torque wrenches and subse- . Ident. No. 601: quently removing a er measurements. . No separate torque screwdriver or reference arm required . Lowers costs, safe and rapid working Execution: . User-friendly . Ident. No. 601: Delivery: . Release signal when the angle of rotation is reached Ident. No. 601: incl. battery (micro 1.5 V), in case with foam insert

Angle of rotation module, mounted

Ident. No. 601 Angle of rotation module

Ident. No. 500 500 52282... USB adapter, cable, so ware Ident. No. ● Angle of rotation module Ident. No. 601 52282... ● Prod. Gr. 531

Open-end wrench plug-in tools For torque wrench with square plug-in sha

Technical data: . Surface: Chrome-plated . Material: Chrome-vanadium steel

No. 52286 No. 52287 007–52287 019 No. 52287 113–52287 136

Width across ﬂ ats 7 mm 8 mm 9 mm 10 mm 11 mm 12 mm 13 mm Insert shank square 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm Ident. No. 007 008 009 010 011 012 013 52286... ● ● ● ● ● ● ● Ident. No. 007 008 009 010 011 012 013 52287... ● ● ● ● ● ● ● Width across ﬂ ats 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm 13 mm Insert shank square 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 14 x 18 mm Ident. No. 014 015 016 017 018 019 113 52286... ● ● ● ● ● ● ● Ident. No. 014 015 016 017 018 019 113 52287... ● ● ● ● ● ● ●

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1385 Availability subject to country specific rules and regulations.

1385_EN_2018_KERN[21850944]-p.indd 1385 12/17/2018 3:35:59 PM Screwdrivers \ Torque wrench

Width across ﬂ ats 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm 21 mm Insert shank square 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 114 115 116 117 118 119 121 52286... Ident. No. ● ● ● ● ● ● ● 114 115 116 117 118 119 121 52287... Ident. No. ● ● ● ● ● ● ● Width across ﬂ ats 22 mm 24 mm 27 mm 30 mm 32 mm 34 mm 36 mm Insert shank square 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm Ident. No. 122 124 127 130 132 134 136 52286... ● ● ● ● ● ● ● 122 124 127 130 132 134 136 52287... Ident. No. ● ● ● ● ● ● ● STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569 Box wrench plug-in tools For torque wrench with square plug-in sha

Technical data: . Surface: Chrome-plated . Material: Chrome-vanadium steel

No. 52286 No. 52287 207–52287 222 No. 52287 313–52287 341

Width across fl ats 7 mm 8 mm 10 mm 11 mm 12 mm 13 mm 14 mm Insert shank square 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm Ident. No. 207 208 210 211 212 213 214 52286... ● ● ● ● ● ● ● Ident. No. 207 208 210 211 212 213 214 52287... ● ● ● ● ● ● ● Width across fl ats 15 mm 16 mm 17 mm 18 mm 19 mm 21 mm 22 mm Insert shank square 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 9 x 12 mm 215 216 217 218 219 221 222 52286... Ident. No. ● ● ● ● ● ● ● 215 216 217 218 219 221 222 52287... Ident. No. ● ● ● ● ● ● ● Width across fl ats 13 mm 14 mm 15 mm 16 mm 17 mm 18 mm 19 mm Insert shank square 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 313 314 315 316 317 318 319 52286... Ident. No. ● ● ● ● ● ● ● 313 314 315 316 317 318 319 52287... Ident. No. ● ● ● ● ● ● ● Width across fl ats 21 mm 22 mm 24 mm 27 mm 30 mm 32 mm 34 mm Insert shank square 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 14 x 18 mm 321 322 324 327 330 332 334 52286... Ident. No. ● ● ● ● ● ● ● Ident. No. 321 322 324 327 330 332 334 52287... ● ● ● ● ● ● ● Width across fl ats 36 mm 41 mm Insert shank square 14 x 18 mm 14 x 18 mm Ident. No. 336 341 52286... ● ● Ident. No. 336 341 52287... ● ● STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569 Plug-in square drives For torque wrench

Execution: Technical data: . DIN 3120 drive . Insert shank square: 14 x 18 mm . Surface: Chrome-plated . Material: Chrome-vanadium steel

Tip size 1/2 inch 3/4 inch Ident. No. 550 555 52286... ● ● Prod. Gr. 569

Source: Hahn+Kolb Werkzeuge GmbH 1386Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1385_EN_2018_KERN[21850944]-p.indd 1386 12/17/2018 3:36:02 PM Screwdrivers \ Torque wrench

Plug-in square drives For torque wrench with square plug-in sha

Technical data: . Surface: Chrome-plated . Material: Chrome-vanadium steel

Tip size 1/4 inch 3/8 inch 1/2 inch 1/2 inch 3/4 inch Insert shank square 9 x 12 mm 9 x 12 mm 9 x 12 mm 14 x 18 mm 14 x 18 mm Max. load force (N) 40 80 100 300 650 Ident. No. 540, 550 Ident. No. 540 545 550 553 555 52287... ● ● ● ● ● Prod. Gr. 531

Ident. No. 545, 553–555

Plug-in reversible ratchets For torque wrench

Application: Technical data: Ident. No. 650: for torque wrenches . Surface: Chrome-plated . Material: Chrome-vanadium steel

Tip size 1/4 inch 3/8 inch 1/2 inch 1/2 inch Insert shank square 9 x 12 mm 9 x 12 mm 9 x 12 mm 14 x 18 mm Max. load force (N) 40 120 120 300 Number of teeth 20 30 32 32 Ident. No. 600 605 610 650 52286... ● ● ● ● Prod. Gr. 569

Plug-in reversible ratchets For torque wrench

Application: Technical data: No. 52286 655: for torque wrenches . Surface: Chrome-plated . Material: Chrome-vanadium steel Execution: . No. 52287: . With fail-safe connection . Quick Release with safety locking device

No. 52286

No. 52287 615–52287 625 Tip size 1/4 inch 3/8 inch 1/2 inch 1/2 inch 1/4 inch 1/2 inch 1/2 inch Insert shank square 9 x 12 mm 9 x 12 mm 9 x 12 mm 14 x 18 mm 9 x 12 mm 9 x 12 mm 14 x 18 mm Max. load force (N) 40 100 100 250 40 100 250 Number of teeth 20 30 32 32 22 30 36 Ident. No. 615 620 625 655 52286... ● ● ● ● - - - Ident. No. - 620 615 625 655 52287... ● - - ● ● ● STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1387 Availability subject to country specific rules and regulations.

1387_EN_2018_KERN[21850947]-t.indd 1387 12/17/2018 3:35:58 PM Screwdrivers \ Torque wrench

Plug-in reversible ratchet for torque screwdriver with square plug in sha

Execution: Technical data: . Deeper-inset switching mechanism protects . Insert shank square: 14 x 18 mm against unintentional switching . Max. torque: 200 Nm . Deep-set . Surface: Chrome-plated . Material: Chrome-vanadium steel . Flat design for optimum access . Ratchet with 40 teeth

Tip size 3/8 inch 1/2 inch Ident. No. 616 617 52286... ● ● Prod. Gr. 569

Plug-in ﬁ ne-toothed reversible ratchets For torque wrench

Application: Technical data: for torque wrenches . Surface: Chrome-plated . Material: Chrome-vanadium steel

No. 52286

No. 52287 630–52287 635

Tip size 3/8 inch 1/2 inch 1/2 inch 3/4 inch 3/8 inch 1/2 inch 1/2 inch 3/4 inch Insert shank square 9 x 12 mm 9 x 12 mm 14 x 18 mm 14 x 18 mm 9 x 12 mm 9 x 12 mm 14 x 18 mm 14 x 18 mm Max. load force (N) 100 100 300 400 100 100 300 400 Number of teeth 72 72 72 72 60 60 60 60 630 635 660 665 52286... Ident. No. ● ● ● ● - - - - 630 635 660 665 52287... Ident. No. - - - - ● ● ● ● STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569

Plug-in reversible ratchet for bits for torque screwdriver

Technical data: . Insert shank square: 9 x 12 mm . Surface: Chrome-plated . Material: Chrome-vanadium steel

Tip size 1/4 inch 5/16 inch Ident. No. 640 645 52286... ● ● Prod. Gr. 569

Source: Hahn+Kolb Werkzeuge GmbH 1388Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1387_EN_2018_KERN[21850947]-t.indd 1388 12/17/2018 3:36:00 PM Screwdrivers \ Torque wrench

Plug-in adapter for torque wrench

Notes: Technical data: Observe the change in torque forces. . Tip size: 14 x 18 mm . Insert shank square: 9 x 12 mm . Surface: Chrome-plated . Material: Chrome-vanadium steel

52286... Ident. No. 700 ● No. 52287 700 No. 52286 52287... Ident. No. ● STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569

Weld-on wrench plug-in tools

Technical data: . Surface: Bare . Material: Chrome-vanadium steel

Insert shank square 9 x 12 mm 14 x 18 mm 800 850 52286... Ident. No. ● ● 800 850 52287... Ident. No. ● ● No. 52286 No. 52287 STAHLWILLE = Prod. Gr. 531 HAZET = Prod. Gr. 569 Torque multipliers

Application: Advantage: For extremely high torques or stiﬀ screw connec- . No need for an extremely long lever; risk of injury tions, using a torque wrench. is reduced to a minimum Execution: Delivery: . Planetary gear with hardened cogs Torque multiplier, slanted support, spare torsion pin, . Protected against overload via torsion pin setting table, operating instructions - all in a robust plastic case with foam inlay. . Compact design and lightweight Technical data: . Response arm form: Cranked

Max. output torque (Nm) 1800 2800 3800 5000 Max. input torque (Nm) 500 215 290 295 Transmission ratio 1:3.6 01:13 01:13 01:17 Drive 3/4 inch 1 inch 1 inch 3/4 inch Tip size 1 inch 1 inch 1 inch 1 1/2 inch Weight (kg) 3 5.2 5.2 7.7 Ident. No. 018 028 038 050 52291... ● ● ○ ○ Prod. Gr. 534 DREMOPLUS ALU torque multiplier

Application: . Guaranteed accuracy: better than ± 3 tolerance In conjunction with a torque wrench, suitable for controlled tightening of bolts . Output square with hole for power screw inserts with locking pin and ring and for loosening screw connections. . Ident. No. 001, 003, 005: With oﬀ set reaction arm, Z form, in chrome-vanadium steel Execution: . Ident. No. 002, 004: With straight reaction arm, L form, with adjustable reac- . Mechanical, hand-operated torque multiplier tion square, in light alloy . With single-stage planetary gear box . Housing made of high-performance aluminium Delivery: In robust transport case with foam inlay

Ident. No. 001 Ident. No. 002, 004 Ident. No. 003, 005

Max. output torque (Nm) 1300 2000 2000 2800 2800 Max. input torque (Nm) 950 580 580 550 550 Transmission ratio 1:5 1:4 1:4 1:5.5 1:5.5 Drive 1/2 inch 3/4 inch 3/4 inch 3/4 inch 3/4 inch Tip size 3/4 inch 1 inch 1 inch 1 inch 1 inch Response arm form Cranked Straight Cranked Straight Cranked Weight (kg) 1.9 2.5 2.9 3.4 3.9 Ident. No. 001 002 003 004 005 52290... ○ ○ ○ ○ ○ Prod. Gr. 556 Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1389 Availability subject to country specific rules and regulations.

1389_EN_2018_KERN[21850950]-q.indd 1389 12/17/2018 3:35:58 PM Screwdrivers \ Torque wrench

DremoTest E electronic torque tester With calibration certiﬁ cate

Application: . Convertible between Nm and lbf. , integrated For checking and adjusting all clockwise torque measuring transducer wrenches used in workshops, in industry and for . Serial RS232 interface quality assurance processes. Advantage: Execution: . Simple to use and with a robust design . With auto-reset function . 1st peak value recognition (ﬁ rst peak/crunch point Technical data: recognition) . Error limit (%): 1 % . Fixed hexagonal box nut mount Min./max. torque measuring range 0.9-55 Nm 9-320 Nm 90-1100 Nm Drive 1/4 inch | 3/8 inch 3/8 inch | 1/2 inch 1/2 inch | 3/4 inch Ident. No. 550 600 650 52292... ● ● ● Prod. Gr. 556

SmartCheck testers for torque wrenches With calibration certiﬁ cate

Execution: . display deviation of maximum +/- 1% guarantees . Easy-to-understand operation and user interface highly reliable measurement data ensure fast, reliable results and a high level of . provides three operating modes (track, ﬁ rst peak, safety. peak hold) and three units (N-m, -lb, in- ). . Splash-proof display and membrane keyboard. . Operation either via power pack or battery . housing made of impact-resistant plastic . ref. no. 001 specially for the calibration of torque . can be placed almost anywhere - horizontal or screwdrivers vertical mounting possible. Delivery: . turning and swivelling display for perfect reada- in robust transport box bility in any position Min./max. torque measuring range 1-10 Nm 1-10 Nm 10-100 Nm 40-400 Nm 80-800 Nm SmartCheck SmartCheck SmartCheck SmartCheck SmartCheck Model 10S 10 100 400 800 Drive 1/4 inch 1/4 inch 3/8 inch 3/4 inch 3/4 inch Error limit (%) (%) 1 1 1 1 1 Ident. No. 001 010 100 400 800 52295... ○ ○ ○ ○ ○ Prod. Gr. 531

Sensotork electronic workshop torque testing device with calibration certiﬁ cate

Application: . Easy to expand using replaceable measuring value For checking and adjusting torque wrenches for transducers clockwise and anti-clockwise measurements. . High degree of accuracy Execution: Delivery: . Possible to transfer data to a PC Measuring value transducer, display unit, power . Measuring units: Nm, -lb, modes: Track, Peak supply unit, fastening kit, square adapter Hold, First Peak Technical data: Advantage: . Error limit (%): 1 % . Compact design Min./max. torque measuring range 0.4-20 Nm 4-200 Nm 25-1100 Nm Drive 1/4 inch 1/2 inch 3/4 inch Ident. No. 210 220 230 52293... ○ ○ ○ Prod. Gr. 531

Source: Hahn+Kolb Werkzeuge GmbH 1390Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1389_EN_2018_KERN[21850950]-q.indd 1390 12/17/2018 3:36:02 PM