Hard disk drive From Wikipedia, the free encyclopedia

A (HDD), hard disk, hard Hard disk drive drive or fixed disk[b] is a device used for storing and retrieving digital information using one or more rigid ("hard") rapidly rotating disks (platters) coated with magnetic material. The platters are paired with magnetic heads arranged on a moving actuator arm, which read and write data to the platter surfaces.[2] Data is accessed in a random- access manner, meaning that individual A 2.5-inch SATA hard drive blocks of data can be stored or retrieved in any order rather than sequentially. An Date 24 December 1954[a] HDD retains its data even when powered invented off. Invented by IBM team led by Rey Johnson Introduced by IBM in 1956,[3] HDDs became the dominant secondary storage device for general-purpose by the early 1960s. Continuously improved, HDDs have maintained this position into the modern era of servers and personal computers. More than 200 companies have produced HDD units, though most current units are manufactured by Seagate, and . Worldwide disk storage revenues were US $32 billion in 2013, down A disassembled and labeled 3% from 2012.[4] 1997 HDD lying atop a mirror

The primary characteristics of an HDD are its capacity and performance. Capacity is specified in unit prefixes corresponding to powers of 1000: a 1-terabyte (TB) drive has a capacity of 1,000 gigabytes (GB; where 1 gigabyte = 1 billion bytes). Typically, some of an HDD's capacity is unavailable to the user because it is used by the file system and the , and possibly An overview of how HDDs inbuilt redundancy for error correction and work recovery. Performance is specified by the time required to move the heads to a track or cylinder (average access time) plus the time it takes for the desired sector to move under the head (average latency, which is a function of the physical rotational speed in revolutions per minute), and finally the speed at which the data is transmitted (data rate).

The two most common form factors for modern HDDs are 3.5-inch, for desktop computers, and 2.5-inch, primarily for laptops. HDDs are connected to systems by standard interface cables such as SATA (Serial ATA), USB or SAS (Serial attached SCSI) cables.

As of 2015, the primary competing technology for secondary storage is in the form of solid-state drives (SSDs), which have higher data transfer rates and significantly lower latency and access times, but HDDs remain the dominant medium for secondary storage due to advantages in price per unit of storage and recording capacity.[5][6] However, SSDs are replacing HDDs where speed, power consumption and durability are more important considerations.[7][8]

Contents

1 History 2 Technology 2.1 Magnetic recording 2.2 Components 2.3 Error rates and handling 2.4 Future development 3 Capacity 3.1 Calculation 3.2 System use 3.3 Units 4 Form factors 5 Performance characteristics 5.1 Time to access data 5.2 Seek time 5.3 Latency 5.4 Data transfer rate 5.5 Other considerations 6 Access and interfaces 7 Integrity and failure 8 Market segments 9 Manufacturers and sales 10 External hard disk drives 11 Visual representation 12 See also 13 Notes 14 References 15 Further reading 16 External links

History

Video of modern HDD operation (cover removed)

Improvement of HDD characteristics over time Parameter Started with Developed to Improvement Capacity two-million-to- [9] eight terabytes (formatted) 3.75 megabytes one Physical 68 cubic feet 2.1 cubic inches (34 cc)[10] 57,000-to-one volume (1.9 m3)[c][3] 2,000 pounds Weight 2.2 ounces (62 g)[10] 15,000-to-one (910 kg)[3] Average about about a few milliseconds access time 600 milliseconds[3] 200-to-one US$9,200 per < $0.05 per gigabyte by 180-million-to- Price megabyte[11] 2013[12] one 2,000 bits per 826 gigabits per square > 400-million- Areal density square inch[13] inch in 2014[14] to-one

HDDs were introduced in 1956 as data storage for an IBM real-time transaction processing computer and were developed for use with general-purpose mainframe and minicomputers. The first IBM drive, the 350 RAMAC, was approximately the size of two refrigerators and stored five million six-bit characters (3.75 megabytes)[9] on a stack of 50 disks.

In 1962 IBM introduced the model 1311 disk drive, which was about the size of a washing machine and stored two million characters on a removable . Users could buy additional packs and interchange them as needed, much like reels of magnetic tape. Later models of removable pack drives, from IBM and others, became the norm in most computer installations and reached capacities of 300 megabytes by the early 1980s. Non-removable HDDs were called "fixed disk" drives.

Some high-performance HDDs were manufactured with one head per track (e.g. IBM 2305) so that no time was lost physically moving the heads to a track.[15] Known as fixed-head or head-per-track disk drives they were very expensive and are no longer in production.[16]

In 1973, IBM introduced a new type of HDD codenamed "Winchester". Its primary distinguishing feature was that the disk heads were not withdrawn completely from the stack of disk platters when the drive was powered down. Instead, the heads were allowed to "land" on a special area of the disk surface upon spin- down, "taking off" again when the disk was later powered on. This greatly reduced the cost of the head actuator mechanism, but precluded removing just the disks from the drive as was done with the disk packs of the day. Instead, the first models of "Winchester technology" drives featured a removable disk module, which included both the disk pack and the head assembly, leaving the actuator motor in the drive upon removal. Later "Winchester" drives abandoned the concept and returned to non-removable platters.

Like the first removable pack drive, the first "Winchester" drives used platters 14 inches (360 mm) in diameter. A few years later, designers were exploring the possibility that physically smaller platters might offer advantages. Drives with 1 non-removable eight-inch platters appeared, and then drives that used a 5 ⁄4 in (130 mm) form factor (a mounting width equivalent to that used by contemporary drives). The latter were primarily intended for the then-fledgling personal computer (PC) market.

As the 1980s began, HDDs were a rare and very expensive additional feature in PCs, but by the late 1980s their cost had been reduced to the point where they were standard on all but the cheapest computers.

Most HDDs in the early 1980s were sold to PC end users as an external, add-on subsystem. The subsystem was not sold under the drive manufacturer's name but under the subsystem manufacturer's name such as Corvus Systems and Tallgrass Technologies, or under the PC system manufacturer's name such as the Apple ProFile. The IBM PC/XT in 1983 included an internal 10 MB HDD, and soon thereafter internal HDDs proliferated on personal computers.

External HDDs remained popular for much longer on the Apple Macintosh. Every Mac made between 1986 and 1998 has a SCSI port on the back, making external expansion easy; also, "toaster" Compact Macs did not have easily accessible HDD bays (or, in the case of the Mac Plus, any hard drive bay at all), so on those models, external SCSI disks were the only reasonable option.

The 2011 Thailand floods damaged manufacturing plants, and impacted hard disk drive cost adversely in 2011–2013.[17]

Driven by ever increasing areal density since their invention, HDDs have continuously improved their characteristics; a few highlights are listed in the table above. At the same time, market application expanded from mainframe computers of the late 1950s to most mass storage applications including computers and consumer applications such as storage of entertainment content. Technology

Magnetic recording

An HDD records data by magnetizing a thin film of ferromagnetic material[d] on a disk. Sequential changes in the direction of magnetization represent binary data bits. The data is read from the disk by detecting the transitions in magnetization. User data is encoded using an Magnetic cross section & encoding scheme, such as run-length limited frequency modulation encoded binary data encoding,[e] which determines how the data is represented by the magnetic transitions.

A typical HDD design consists of a spindle that holds flat circular disks, also called platters, which hold the recorded data. The platters are made from a non- magnetic material, usually aluminium alloy, glass, or ceramic, and are coated with a shallow layer of magnetic material typically 10–20 nm in depth, with an outer layer of carbon for protection.[19][20][21] For reference, a standard piece of copy paper is 0.07–0.18 millimetres (70,000–180,000 nm).[22]

The platters in contemporary HDDs are spun at speeds varying from 4,200 rpm in energy- efficient portable devices, to 15,000 rpm for high- performance Diagram labeling the major servers.[24] The first components of a computer HDDs spun at Recording of single HDD 1,200 rpm[3] and, for magnetisations of bits on a many years, 200 MB HDD-platter 3,600 rpm was the norm.[25] As of December 2013, (recording made visible using the platters in most consumer-grade HDDs spin at CMOS-MagView).[23] either 5,400 rpm or 7,200 rpm.

Information is written to and read from a platter as it rotates past devices called read-and-write heads that operate very close (often tens of nanometers) over the magnetic surface. The read-and-write head is used to detect and modify the magnetization of the material immediately under it.

In modern drives there is one head for each magnetic platter surface on the spindle, mounted Longitudinal recording on a common arm. An actuator arm (or access arm) (standard) & perpendicular moves the heads on an arc (roughly radially) across recording diagram the platters as they spin, allowing each head to access almost the entire surface of the platter as it spins. The arm is moved using a voice coil actuator or in some older designs a stepper motor. Early hard disk drives wrote data at some constant bits per second, resulting in all tracks having the same amount of data per track but modern drives (since the 1990s) use zone bit recording—increasing the write speed from inner to outer zone and thereby storing more data per track in the outer zones.

In modern drives, the small size of the magnetic regions creates the danger that their magnetic state might be lost because of thermal effects, thermally induced magnetic instability which is commonly known as the "superparamagnetic limit." To counter this, the platters are coated with two parallel magnetic layers, separated by a 3-atom layer of the non-magnetic element ruthenium, and the two layers are magnetized in opposite orientation, thus reinforcing each other.[26] Another technology used to overcome thermal effects to allow greater recording densities is perpendicular recording, first shipped in 2005,[27] and as of 2007 the technology was used in many HDDs.[28][29][30]

Components

A typical HDD has two electric motors; a spindle motor that spins the disks and an actuator (motor) that positions the read/write head assembly across the spinning disks. The disk motor has an external rotor attached to the disks; the stator windings are fixed in place. Opposite the actuator at the end of the head support arm is the read-write head; thin printed-circuit cables connect the read-write heads to amplifier electronics mounted at the pivot of the HDD with disks and motor hub actuator. The head support arm is very light, but removed exposing copper also stiff; in modern drives, acceleration at the colored stator coils head reaches 550 g. surrounding a bearing in the center of the spindle motor. The actuator is a Orange stripe along the side of permanent magnet the arm is thin printed-circuit and moving coil cable, spindle bearing is in the motor that swings center and the actuator is in the heads to the the upper left desired position. A metal plate supports a squat neodymium- iron-boron (NIB) high-flux magnet. Beneath this plate is the moving coil, often referred to as the Head stack with an actuator voice coil by analogy to the coil in loudspeakers, coil on the left and read/write which is attached to the actuator hub, and beneath heads on the right that is a second NIB magnet, mounted on the bottom plate of the motor (some drives only have one magnet).

The voice coil itself is shaped rather like an arrowhead, and made of doubly coated copper magnet wire. The inner layer is insulation, and the outer is thermoplastic, which bonds the coil together after it is wound on a form, making it self-supporting. The portions of the coil along the two sides of the arrowhead (which point to the actuator bearing center) interact with the magnetic field, developing a tangential force that rotates the actuator. Current flowing radially outward along one side of the arrowhead and radially inward on the other produces the tangential force. If the magnetic field were uniform, each side would generate opposing forces that would cancel each other out. Therefore, the surface of the magnet is half N pole, half S pole, with the radial dividing line in the middle, causing the two sides of the coil to see opposite magnetic fields and produce forces that add instead of canceling. Currents along the top and bottom of the coil produce radial forces that do not rotate the head.

The HDD's electronics control the movement of the actuator and the rotation of the disk, and perform reads and writes on demand from the disk controller. Feedback of the drive electronics is accomplished by means of special segments of the disk dedicated to servo feedback. These are either complete concentric circles (in the case of dedicated servo technology), or segments interspersed with real data (in the case of embedded servo technology). The servo feedback optimizes the signal to noise ratio of the GMR sensors by adjusting the voice-coil of the actuated arm. The spinning of the disk also uses a servo motor. Modern disk is capable of scheduling reads and writes efficiently on the platter surfaces and remapping sectors of the media which have failed.

Error rates and handling

Modern drives make extensive use of error correction codes (ECCs), particularly Reed–Solomon error correction. These techniques store extra bits, determined by mathematical formulas, for each block of data; the extra bits allow many errors to be corrected invisibly. The extra bits themselves take up space on the HDD, but allow higher recording densities to be employed without causing uncorrectable errors, resulting in much larger storage capacity.[31] For example, a typical 1 TB hard disk with 512-byte sectors provides additional capacity of about 93 GB for the ECC data.[32]

In the newest drives, as of 2009, low-density parity-check codes (LDPC) were supplanting Reed-Solomon; LDPC codes enable performance close to the Shannon Limit and thus provide the highest storage density available.[33]

Typical hard disk drives attempt to "remap" the data in a physical sector that is failing to a spare physical sector provided by the drive's "spare sector pool" (also called "reserve pool"),[34] while relying on the ECC to recover stored data while the amount of errors in a bad sector is still low enough. The S.M.A.R.T (Self- Monitoring, Analysis and Reporting Technology) feature counts the total number of errors in the entire HDD fixed by ECC (although not on all hard drives as the related S.M.A.R.T attributes "Hardware ECC Recovered" and "Soft ECC Correction" are not consistently supported), and the total number of performed sector remappings, as the occurrence of many such errors may predict an HDD failure.

The "No-ID Format", developed by IBM in the mid-1990s, contains information about which sectors are bad and where remapped sectors have been located.[35]

Only a tiny fraction of the detected errors ends up as not correctable. For example, specification for an enterprise SAS disk (a model from 2013) estimates this fraction to be one uncorrected error in every 1016 bits,[36] and another SAS enterprise disk from 2013 specifies similar error rates.[37] Another modern (as of 2013) enterprise SATA disk specifies an error rate of less than 10 non- recoverable read errors in every 1016 bits.[38] An enterprise disk with a Fibre Channel interface, which uses 520 byte sectors to support the Data Integrity Field standard to combat data corruption, specifies similar error rates in 2005.[39]

The worst type of errors are those that go unnoticed, and are not even detected by the disk firmware or the host operating system. These errors are known as silent data corruption, some of which may be caused by hard disk drive malfunctions.[40]

Future development

HDD areal density's long term exponential growth has been similar to a 41% per year Moore's law rate; the rate was 60–100% per year beginning in the early 1990s and continuing until about 2005,[41][42] an increase which Gordon Moore (1997) called "flabbergasting" and he speculated that HDDs had "moved at least as fast as the semiconductor complexity."[43] However, the rate decreased dramatically around 2006 and, during Leading-edge hard disk drive 2011–2014, growth was in the annual range of 5– areal densities from 1956 through 2009 compared to [44] 10%. Disk cost per byte improved nearly -45% Moore's law per year during 1990–2010, and slowed after 2010 due to the Thailand floods and difficulty in migrating from perpendicular recording to newer technologies.[45][46][47] Moore (2005) further observed that growth cannot continue forever.[48]

Increasing areal density corresponds to an ever decreasing bit cell size. In 2013, a production desktop 3 TB HDD (with four platters) would have had an areal density of about 500 Gbit/in2 which would have amounted to a bit cell comprising about 18 magnetic grains (11 by 1.6 grains).[49] Since the mid-2000s areal density progress has increasingly been challenged by a superparamagnetic trilemma involving grain size, grain magnetic strength and ability of the head to write.[50] In order to maintain acceptable signal to noise smaller grains are required; smaller grains may self-reverse (thermal instability) unless their magnetic strength is increased, but known write head materials are unable to generate a magnetic field sufficient to write the medium. Several new magnetic storage technologies are being developed to overcome or at least abate this trilemma and thereby maintain the competitiveness of HDDs with respect to products such as flash memory-based solid-state drives (SSDs).

In 2013, Seagate introduced one such technology, shingled magnetic recording (SMR).[51] Additionally, SMR comes with design complexities that may cause reduced write performance.[52][53] Other new recording technologies that, as of 2015, still remain under development include heat-assisted magnetic recording (HAMR),[54][55] microwave-assisted magnetic recording (MAMR),[56] two- dimensional magnetic recording (TDMR),[49][57] bit-patterned recording (BPR),[58] and "current perpendicular to plane" giant magnetoresistance (CPP/GMR) heads.[59][60][61]

Depending upon assumptions on feasibility and timing of these technologies, the median forecast by industry observers and analysts for 2016 and beyond for areal density growth is 20% per year with a range of 10% to 40%.[49][62][63][64][65] The ultimate limit for the BPR technology may be the superparamagnetic limit of a single particle that is estimated to be about two orders of magnitude higher than the 500 Gbits/in2 density represented by 2013 production desktop HDDs.[49] Capacity

The capacity of a hard disk drive, as reported by an operating system to the end user, is smaller than the amount stated by a drive or system manufacturer; this can be caused by a combination of factors: the operating system using some space, different units used while calculating capacity, or data redundancy.

Calculation

Modern hard disk drives appear to their interface as a contiguous set of logical blocks, so the gross drive capacity may be calculated by multiplying the number of blocks by the block size. This information is available from the manufacturer's specification and from the drive itself through use of special utilities invoking low level commands.[66][67]

The gross capacity of older HDDs may be calculated as the product of the number of cylinders per zone, the number of bytes per sector (most commonly 512), and the count of zones of the drive. Some modern SATA drives also report cylinder-head-sector (CHS) values, but these are not actual physical parameters since the reported numbers are constrained by historic operating system interfaces. The C/H/S scheme has been replaced by logical block addressing. In some cases, to try to "force-fit" the CHS scheme to large-capacity drives, the number of heads was given as 64, although no modern drive has anywhere near 32 platters: the typical 2 TB hard disk as of 2013 has two 1 TB platters, and 4 TB drives use four platters.

In modern HDDs, spare capacity for defect management is not included in the published capacity; however, in many early HDDs a certain number of sectors were reserved as spares, thereby reducing the capacity available to end users.

For RAID subsystems, data integrity and fault-tolerance requirements also reduce the realized capacity. For example, a RAID1 subsystem will be about half the total capacity as a result of data mirroring. RAID5 subsystems with x drives, would lose 1/x of capacity to parity. RAID subsystems are multiple drives that appear to be one drive or more drives to the user, but provides a great deal of fault-tolerance. Most RAID vendors use some form of checksums to improve data integrity at the block level. For many vendors, this involves using HDDs with sectors of 520 bytes per sector to contain 512 bytes of user data and eight checksum bytes or using separate 512-byte sectors for the checksum data.[68]

In some systems, there may be hidden partitions used for system recovery that reduce the capacity available to the end user.

System use

The presentation of a hard disk drive to its host is determined by the disk controller. The actual presentation may differ substantially from the drive's native interface, particularly in mainframes or servers. Modern HDDs, such as SAS[66] and SATA[67] drives, appear at their interfaces as a contiguous set of logical blocks that are typically 512 bytes long, though the industry is in the process of changing to the 4,096-byte logical blocks layout, known as the Advanced Format (AF).[69]

The process of initializing these logical blocks on the physical disk platters is called low-level formatting, which is usually performed at the factory and is not normally changed in the field.[70][f] As a next step in preparing an HDD for use, high-level formatting writes partition and file system structures into selected logical blocks to make the remaining logical blocks available to the host's operating system and its applications.[71] The file system uses some of the disk space to structure the HDD and organize files, recording their file names and the sequence of disk areas that represent the file. Examples of data structures stored on disk to retrieve files include the File Allocation Table (FAT) in the DOS file system and inodes in many UNIX file systems, as well as other operating system data structures (also known as metadata). As a consequence, not all the space on an HDD is available for user files, but this system overhead is usually negligible.

Units

Decimal and binary unit prefixes interpretation[72][73] Capacity advertised by Capacity expected by Reported capacity manufacturers[g] consumers[h] Mac OS X With Windows[h] Bytes Bytes Diff. 10.6+[g] prefix 93.1 GB, 100 GB 100,000,000,000 107,374,182,400 7.37% 100 GB 95,367 MB 931 GB, 1,000 GB, 1 TB 1,000,000,000,000 1,099,511,627,776 9.95% 953,674 MB 1,000,000 MB

The total capacity of HDDs is given by manufacturers in SI-based units[i] such as gigabytes (1 GB = 1,000,000,000 bytes) and terabytes (1 TB = 1,000,000,000,000 bytes).[72][74][75][76][77][78] The practice of using SI-based prefixes (denoting powers of 1,000) in the hard disk drive and computer industries dates back to the early days of ;[79] by the 1970s, "million", "mega" and "M" were consistently used in the decimal sense for drive capacity.[80][81][82] However, capacities of memory (RAM, ROM) and CDs are traditionally quoted using binary prefixes, meaning powers of 1,024.

Computers internally do not represent either hard drive or memory capacity in powers of 1,024; reporting it in this manner is a convention.[83] Microsoft Windows family of operating systems uses the binary convention when reporting storage capacity, so a HDD offered by its manufacturer as a 1 TB drive is reported by these operating systems as a 931 GB HDD. Mac OS X 10.6 ("Snow Leopard") uses decimal convention when reporting HDD capacity.[83]

The difference between the decimal and binary prefix interpretation caused some consumer confusion and led to class action suits against HDD manufacturers. The plaintiffs argued that the use of decimal prefixes effectively misled consumers while the defendants denied any wrongdoing or liability, asserting that their marketing and advertising complied in all respects with the law and that no class member sustained any damages or injuries.[84][85][86] Form factors

Past and present HDD form factors Capacity Length Width Height Largest Platters Per Form factor Status [mm] [mm] [mm] capacity (max) platter [GB] 19 or 8 3.5-inch Current 146 101.6 5 or 7[88][j] 1149[87] 25.4 TB[87](2014) 5,[89] 7, 9.5,[k] 2 TB[91] 2.5-inch Current 100 69.85 12.5, 4 667[92] (2012) 15, or 19[90] 320 GB[10] 1.8-inch Current 78.5[l] 54 5 or 8 2 220 [93] (2009) 8-inch Obsolete 362 241.3 117.5 [94] 5.25-inch FH Obsolete 203 146 82.6 47 GB 14 3.36 (1998) 19.3 GB[95] 5.25-inch HH Obsolete 203 146 41.4 4[m] 4.83 (1998) [96] 1.3-inch Obsolete 43 40 GB 1 40 (2007) 1-inch 20 GB (CFII/ZIF/IDE- Obsolete 42 1 20 (2006) Flex) [97][98] 0.85-inch Obsolete 32 24 5 8 GB 1 8 (2004)

IBM's first hard drive, the IBM 350, used a stack of fifty 24-inch platters and was of a size comparable to two large refrigerators. In 1962, IBM introduced its model 1311 disk, which used six 14-inch (nominal size) platters in a removable pack and was roughly the size of a washing machine. This became a standard platter size and drive form- factor for many years, used also by other manufacturers.[99] The IBM 2314 used platters of the same size in an eleven-high pack and 8-, 5.25-, 3.5-, 2.5-, 1.8- and 1- introduced the "drive in a drawer" layout, although inch HDDs, together with a the "drawer" was not the complete drive. ruler to show the length of platters and read-write heads Later drives were designed to fit entirely into a chassis that would mount in a 19-inch rack. Digital's RK05 and RL01 were early examples using single 14-inch platters in removable packs, the entire drive fitting in a 10.5-inch-high rack space (six rack units). In the mid-to-late 1980s the similarly sized Fujitsu Eagle, which used (coincidentally) 10.5-inch platters, was a popular product.

Such large platters were never used with -based systems. With increasing sales of microcomputers having built in floppy-disk A newer 2.5-inch (63.5 mm) drives (FDDs), HDDs that would fit to the FDD 6,495 MB HDD compared to mountings became desirable. Thus HDD Form an older 5.25-inch full-height factors, initially followed those of 8-inch, 5.25-inch, 110 MB HDD and 3.5-inch floppy disk drives. Because there were no smaller floppy disk drives, smaller HDD form factors developed from product offerings or industry standards.

8-inch 9.5 in × 4.624 in × 14.25 in (241.3 mm × 117.5 mm × 362 mm). In 1979, Shugart Associates' SA1000 was the first form factor compatible HDD, having the same dimensions and a compatible interface to the 8" FDD. 5.25-inch 5.75 in × 3.25 in × 8 in (146.1 mm × 82.55 mm × 203 mm). This smaller form factor, first used in an HDD by Seagate in 1980,[100] was the same size as 1 full-height 5 ⁄4-inch-diameter (130 mm) FDD, 3.25-inches high. This is twice as high as "half height"; i.e., 1.63 in (41.4 mm). Most desktop models of drives for optical 120 mm disks (DVD, CD) use the half height 5¼" dimension, but it fell out of fashion for HDDs. The format was standardized as EIA-741 and co-published as SFF-8501 for disk drives, with other SFF-85xx series standards covering related 5.25 inch devices (optical drives, etc.)[101] The Quantum Bigfoot HDD was the last to use it in the late 1990s, with "low- profile" (≈25 mm) and "ultra-low-profile" (≈20 mm) high versions. 3.5-inch 4 in × 1 in × 5.75 in (101.6 mm × 25.4 mm × 146 mm) = 376.77344 cm³. This smaller form factor is similar to that used in an HDD by Rodime in 1983,[102] which was the same size as the "half height" 3½" FDD, i.e., 1.63 inches high. Today, the 1-inch high ("slimline" or "low-profile") version of this form factor is the most popular form used in most desktops. The format was standardized in terms of dimensions and positions of mounting holes as EIA/ECA-740, co-published as SFF-8301.[103] 2.5-inch 2.75 in × 0.275–0.75 in × 3.945 in (69.85 mm × 7–19 mm × 100 mm) = 48.895–132.715 cm3. This smaller form factor was introduced by PrairieTek in 1988;[104] there is no corresponding FDD. The 2.5-inch drive format is standardized in the EIA/ECA-720 co-published as SFF-8201; when used with specific connectors, more detailed specifications are SFF-8212 for the 50-pin (ATA laptop) connector, SFF-8223 with the SATA, or SAS connector and SFF- 8222 with the SCA-2 connector.[105] It came to be widely used for HDDs in mobile devices (laptops, music players, etc.) and for solid-state drives (SSDs), by 2008 replacing some 3.5 inch enterprise-class drives.[106] It is also used in the PlayStation 3[107] and Xbox 360 video game consoles. Drives 9.5 mm high became an unofficial standard for all except the largest- capacity laptop drives (usually having two platters inside); 12.5 mm-high drives, typically with three platters, are used for maximum capacity, but will not fit most laptop computers. Enterprise-class drives can have a height up to 15 mm.[108] Seagate released a 7 mm drive aimed at entry level laptops and high end netbooks in December 2009.[109] Western Digital released on April 23, 2013 a hard drive 5 mm in height specifically aimed at UltraBooks.[110] 1.8-inch 54 mm × 8 mm × 78.5 mm[l] = 33.912 cm³. This form factor, originally introduced by Integral Peripherals in 1993, evolved into the ATA-7 LIF with dimensions as stated. For a time it was increasingly used in digital audio players and subnotebooks, but its popularity decreased to the point where this form factor is increasingly rare and only a small percentage of the overall market.[111] There was an attempt to standardize this format as SFF- 8123, but it was cancelled in 2005.[112] SATA revision 2.6 standardized the internal Micro SATA connector and device dimensions. 1-inch 42.8 mm × 5 mm × 36.4 mm. This form factor was introduced in 1999 as IBM's Microdrive to fit inside a CF Type II slot. Samsung calls the same form factor "1.3 inch" drive in its product literature.[113] 0.85-inch 24 mm × 5 mm × 32 mm. Toshiba announced this form factor in January 2004[114] for use in mobile phones and similar applications, including SD/MMC slot compatible HDDs optimized for video storage on 4G handsets. Toshiba manufactured a 4 GB (MK4001MTD) and an 8 GB (MK8003MTD) version and holds the Guinness World Record for the smallest HDD.[115][116]

As of 2012, 2.5-inch and 3.5-inch hard disks were the most popular sizes.

By 2009 all manufacturers had discontinued the development of new products for the 1.3-inch, 1-inch and 0.85-inch form factors due to falling prices of flash memory,[117][118] which has no moving parts.

While these sizes are customarily described by an approximately correct figure in inches, actual sizes have long been specified in millimeters. Performance characteristics

Time to access data

The factors that limit the time to access the data on an HDD are mostly related to the mechanical nature of the rotating disks and moving heads. Seek time is a measure of how long it takes the head assembly to travel to the track of the disk that contains data. Rotational latency is incurred because the desired disk sector may not be directly under the head when data transfer is requested. These two delays are on the order of milliseconds each. The bit rate or data transfer rate (once the head is in the right position) creates delay which is a function of the number of blocks transferred; typically relatively small, but can be quite long with the transfer of large contiguous files. Delay may also occur if the drive disks are stopped to save energy.

An HDD's Average Access Time is its average seek time which technically is the time to do all possible seeks divided by the number of all possible seeks, but in practice is determined by statistical methods or simply approximated as the time of a seek over one-third of the number of tracks.[119]

Defragmentation is a procedure used to minimize delay in retrieving data by moving related items to physically proximate areas on the disk.[120] Some computer operating systems perform defragmentation automatically. Although automatic defragmentation is intended to reduce access delays, performance will be temporarily reduced while the procedure is in progress.[121]

Time to access data can be improved by increasing rotational speed (thus reducing latency) or by reducing the time spent seeking. Increasing areal density increases throughput by increasing data rate and by increasing the amount of data under a set of heads, thereby potentially reducing seek activity for a given amount of data. The time to access data has not kept up with throughput increases, which themselves have not kept up with growth in bit density and storage capacity.

Seek time

Average seek time ranges from under 4 ms for high-end server drives[122] to 15 ms for mobile drives, with the most common mobile drives at about 12 ms[123] and the most common desktop type typically being around 9 ms. The first HDD had an average seek time of about 600 ms;[3] by the middle of 1970s HDDs were available with seek times of about 25 ms.[124] Some early PC drives used a stepper motor to move the heads, and as a result had seek times as slow as 80– 120 ms, but this was quickly improved by voice coil type actuation in the 1980s, reducing seek times to around 20 ms. Seek time has continued to improve slowly over time.

Some desktop and laptop computer systems allow the user to make a tradeoff between seek performance and drive noise. Faster seek rates typically require more energy usage to quickly move the heads across the platter, causing louder noises from the pivot bearing and greater device vibrations as the heads are rapidly accelerated during the start of the seek motion and decelerated at the end of the seek motion. Quiet operation reduces movement speed and acceleration rates, but at a cost of reduced seek performance.

Latency

Rotational speed Average latency [rpm] [ms] 15,000 2 10,000 3 7,200 4.16 5,400 5.55 4,800 6.25

Latency is the delay for the rotation of the disk to bring the required disk sector under the read-write mechanism. It depends on rotational speed of a disk, measured in revolutions per minute (rpm). Average rotational latency is shown in the table on the right, based on the statistical relation that the average latency in milliseconds for such a drive is one-half the rotational period.

Data transfer rate

As of 2010, a typical 7,200-rpm desktop HDD has a sustained "disk-to-buffer" data transfer rate up to 1,030 Mbits/sec.[125] This rate depends on the track location; the rate is higher for data on the outer tracks (where there are more data sectors per rotation) and lower toward the inner tracks (where there are fewer data sectors per rotation); and is generally somewhat higher for 10,000-rpm drives. A current widely used standard for the "buffer-to-computer" interface is 3.0 Gbit/s SATA, which can send about 300 megabyte/s (10-bit encoding) from the buffer to the computer, and thus is still comfortably ahead of today's disk-to- buffer transfer rates. Data transfer rate (read/write) can be measured by writing a large file to disk using special file generator tools, then reading back the file. Transfer rate can be influenced by file system fragmentation and the layout of the files.[120]

HDD data transfer rate depends upon the rotational speed of the platters and the data recording density. Because heat and vibration limit rotational speed, advancing density becomes the main method to improve sequential transfer rates. Higher speeds require a more powerful spindle motor, which creates more heat. While areal density advances by increasing both the number of tracks across the disk and the number of sectors per track, only the latter increases the data transfer rate for a given rpm. Since data transfer rate performance only tracks one of the two components of areal density, its performance improves at a lower rate.

Other considerations

Other performance considerations include power consumption, audible noise, and shock resistance. Access and interfaces

HDDs are accessed over one of a number of bus types, including as of 2011 parallel ATA (PATA, also called IDE or EIDE; described before the introduction of SATA as ATA), Serial ATA (SATA), SCSI, Serial Attached SCSI (SAS), and Fibre Channel. Bridge circuitry is sometimes used to connect HDDs to buses with which they cannot communicate natively, such as IEEE 1394, USB and Inner view of a 1998 Seagate SCSI. HDD that used Parallel ATA interface Modern HDDs present a consistent interface to the rest of the computer, no matter what data encoding scheme is used internally. Typically a DSP in the electronics inside the HDD takes the raw analog voltages from the read head and uses PRML and Reed–Solomon error correction[126] to decode the sector boundaries and sector data, then sends that data out the standard interface. That DSP also watches the error rate detected by error detection 2.5-inch SATA drive on top of a and correction, and performs bad sector 3.5-inch SATA drive, close-up remapping, data collection for Self-Monitoring, of data and power connectors Analysis, and Reporting Technology, and other internal tasks.

Modern interfaces connect an HDD to a host bus interface adapter (today typically integrated into the "south bridge") with one data/control cable. Each drive also has an additional power cable, usually direct to the power supply unit.

Small Computer System Interface (SCSI), originally named SASI for Shugart Associates System Interface, was standard on servers, workstations, Commodore Amiga, Atari ST and Apple Macintosh computers through the mid-1990s, by which time most models had been transitioned to IDE (and later, SATA) family disks. The range limitations of the data cable allows for external SCSI devices. Integrated Drive Electronics (IDE), later standardized under the name AT Attachment (ATA, with the alias P-ATA or PATA (Parallel ATA) retroactively added upon introduction of SATA) moved the HDD controller from the interface card to the disk drive. This helped to standardize the host/controller interface, reduce the programming complexity in the host , and reduced system cost and complexity. The 40-pin IDE/ATA connection transfers 16 bits of data at a time on the data cable. The data cable was originally 40-conductor, but later higher speed requirements for data transfer to and from the HDD led to an "ultra DMA" mode, known as UDMA. Progressively swifter versions of this standard ultimately added the requirement for an 80-conductor variant of the same cable, where half of the conductors provides grounding necessary for enhanced high-speed signal quality by reducing cross talk. EIDE was an unofficial update (by Western Digital) to the original IDE standard, with the key improvement being the use of direct memory access (DMA) to transfer data between the disk and the computer without the involvement of the CPU, an improvement later adopted by the official ATA standards. By directly transferring data between memory and disk, DMA eliminates the need for the CPU to copy byte per byte, therefore allowing it to process other tasks while the data transfer occurs. Fibre Channel (FC) is a successor to parallel SCSI interface on enterprise market. It is a serial protocol. In disk drives usually the Fibre Channel Arbitrated Loop (FC-AL) connection topology is used. FC has much broader usage than mere disk interfaces, and it is the cornerstone of storage area networks (SANs). Recently other protocols for this field, like iSCSI and ATA over have been developed as well. Confusingly, drives usually use copper twisted-pair cables for Fibre Channel, not fibre optics. The latter are traditionally reserved for larger devices, such as servers or disk array controllers. Serial Attached SCSI (SAS). The SAS is a new generation serial communication protocol for devices designed to allow for much higher speed data transfers and is compatible with SATA. SAS uses a mechanically identical data and power connector to standard 3.5-inch SATA1/SATA2 HDDs, and many server-oriented SAS RAID controllers are also capable of addressing SATA HDDs. SAS uses serial communication instead of the parallel method found in traditional SCSI devices but still uses SCSI commands. Serial ATA (SATA). The SATA data cable has one data pair for differential transmission of data to the device, and one pair for differential receiving from the device, just like EIA-422. That requires that data be transmitted serially. A similar differential signaling system is used in RS485, LocalTalk, USB, FireWire, and differential SCSI. Integrity and failure

Due to the extremely close spacing between the heads and the disk surface, HDDs are vulnerable to being damaged by a head crash—a failure of the disk in which the head scrapes across the platter surface, often grinding away the thin magnetic film and causing data loss. Head crashes can be caused by electronic failure, a sudden power failure, physical shock, contamination of the drive's internal enclosure, wear and tear, corrosion, or poorly manufactured platters and heads.

The HDD's spindle system relies on air density Close-up of an HDD head inside the disk enclosure to support the heads at resting on a disk platter; its their proper flying height while the disk rotates. mirror reflection is visible on HDDs require a certain range of air densities in the platter surface. order to operate properly. The connection to the external environment and density occurs through a small hole in the enclosure (about 0.5 mm in breadth), usually with a filter on the inside (the breather filter).[127] If the air density is too low, then there is not enough lift for the flying head, so the head gets too close to the disk, and there is a risk of head crashes and data loss. Specially manufactured sealed and pressurized disks are needed for reliable high-altitude operation, above about 3,000 m (9,800 ft).[128] Modern disks include temperature sensors and adjust their operation to the operating environment. Breather holes can be seen on all disk drives—they usually have a sticker next to them, warning the user not to cover the holes. The air inside the operating drive is constantly moving too, being swept in motion by friction with the spinning platters. This air passes through an internal recirculation (or "recirc") filter to remove any leftover contaminants from manufacture, any particles or chemicals that may have somehow entered the enclosure, and any particles or outgassing generated internally in normal operation. Very high humidity present for extended periods of time can corrode the heads and platters.

For giant magnetoresistive (GMR) heads in particular, a minor head crash from contamination (that does not remove the magnetic surface of the disk) still results in the head temporarily overheating, due to friction with the disk surface, and can render the data unreadable for a short period until the head temperature stabilizes (so called "thermal asperity", a problem which can partially be dealt with by proper electronic filtering of the read signal).

When the logic board of a hard disk fails, the drive can often be restored to functioning order and the data recovered by replacing the circuit board of one of an identical hard disk. In the case of read-write head faults, they can be replaced using specialized tools in a dust-free environment. If the disk platters are undamaged, they can be transferred into an identical enclosure and the data can be copied or cloned onto a new drive. In the event of disk-platter failures, disassembly and imaging of the disk platters may be required.[129] For logical damage to file systems, a variety of tools, including fsck on UNIX-like systems and CHKDSK on Windows, can be used for data recovery. Recovery from logical damage can require file carving.

A common expectation is that hard disk drives designed and marketed for server use will fail less frequently than consumer-grade drives usually used in desktop computers. However, two independent studies by Carnegie Mellon University[130] and Google[131] found that the "grade" of a drive does not relate to the drive's failure rate.

A 2011 summary of research into SSD and magnetic disk failure patterns by Tom's Hardware summarized research findings as follows:[132]

MTBF does not indicate reliability; the annualized failure rate is higher and usually more relevant. Magnetic disks do not have a specific tendency to fail during early use, and temperature only has a minor effect; instead, failure rates steadily increase with age. S.M.A.R.T. warns of mechanical issues but not other issues affecting reliability, and is therefore not a reliable indicator of condition. Failure rates of drives sold as "enterprise" and "consumer" are "very much similar", although customized for their different environments. In drive arrays, one drive's failure significantly increases the short-term chance of a second drive failing. Market segments

Desktop HDDs They typically store between 60 GB and 4 TB and rotate at 5,400 to 10,000 rpm, and have a media transfer rate of 0.5 Gbit/s or higher (1 GB = 109 bytes; 1 Gbit/s = 109 bit/s). As of August 2014, the highest-capacity desktop HDDs store 8 TB.[87][133] Mobile (laptop) HDDs Smaller than their desktop and enterprise counterparts, they tend to be slower and have lower capacity. Mobile HDDs spin at 4,200 rpm, 5,200 rpm, 5,400 rpm, or 7,200 rpm, with 5,400 rpm being typical. 7,200 rpm drives tend to be more expensive and have smaller capacities, while 4,200 rpm models usually have very high storage capacities. Because of smaller platter(s), mobile HDDs generally have lower capacity than their greater desktop Two enterprise-grade SATA counterparts. 2.5-inch 10,000 rpm HDDs, There are also 2.5-inch drives spinning at factory-mounted in 3.5-inch 10,000 rpm, which belong to the enterprise adapter frames segment with no intention to be used in laptops. Enterprise HDDs Typically used with multiple-user computers running enterprise software. Examples are: transaction processing databases, internet infrastructure (email, webserver, e-commerce), scientific computing software, and nearline storage management software. Enterprise drives commonly operate continuously ("24/7") in demanding environments while delivering the highest possible performance without sacrificing reliability. Maximum capacity is not the primary goal, and as a result the drives are often offered in capacities that are relatively low in relation to their cost.[134] The fastest enterprise HDDs spin at 10,000 or 15,000 rpm, and can achieve sequential media transfer speeds above 1.6 Gbit/s[135] and a sustained transfer rate up to 1 Gbit/s.[135] Drives running at 10,000 or 15,000 rpm use smaller platters to mitigate increased power requirements (as they have less air drag) and therefore generally have lower capacity than the highest capacity desktop drives. Enterprise HDDs are commonly connected through Serial Attached SCSI (SAS) or Fibre Channel (FC). Some support multiple ports, so they can be connected to a redundant host bus adapter. Enterprise HDDs can have sector sizes larger than 512 bytes (often 520, 524, 528 or 536 bytes). The additional per-sector space can be used by hardware RAID controllers or applications for storing Data Integrity Field (DIF) or Data Integrity Extensions (DIX) data, resulting in higher reliability and prevention of silent data corruption.[136] Consumer electronics HDDs They include drives embedded into digital video recorders and automotive vehicles. The former are configured to provide a guaranteed streaming capacity, even in the face of read and write errors, while the latter are built to resist larger amounts of shock. Manufacturers and sales

More than 200 companies have manufactured HDDs over time. But consolidations have concentrated production into just three manufacturers today: Western Digital, Seagate, and Toshiba.

Worldwide revenues for disk storage were $32 billion in 2013, down about 3% from 2012.[4] This corresponds to shipments of 552 million units in 2013 compared to 578 million in 2012 and 622 million in 2011.[4] The estimated 2013 market shares are about 40–45% each for Seagate and Western Digital and 13–16% for Toshiba. Diagram of HDD External hard disk drives manufacturer consolidation

External hard disk drives[n] typically connect via USB; variants using USB 2.0 interface generally have slower data transfer rates when compared to internally mounted hard drives connected through SATA. Plug and play drive functionality offers system compatibility and features large storage options and portable design. As of January 2015, available capacities for external hard disk drives range from 500 GB to 6 TB. Toshiba 1 TB 2.5" external USB 2.0 hard disk drive External hard disk drives are usually available as pre-assembled integrated products, but may be also assembled by combining an external enclosure (with USB or other interface) with a separately purchased drive. They are available in 2.5-inch and 3.5-inch sizes; 2.5-inch variants are typically called portable external drives, while 3.5-inch variants are referred to as desktop external drives. "Portable" drives are packaged in smaller and lighter enclosures than the "desktop" drives; additionally, "portable" drives use power provided by the 3.0 TB 3.5" Seagate FreeAgent USB connection, while "desktop" drives require GoFlex plug and play external USB external power bricks. 3.0-compatible drive (left), 750 GB 3.5" push- Features such as biometric security or multiple button external USB 2.0 drive interfaces (for example, Firewire) are available (right), and a 500 GB 2.5" generic at a higher cost.[137] There are pre-assembled brand plug and play external USB external hard disk drives that, when taken out 2.0 drive (front). from their enclosures, cannot be used internally in a laptop or desktop computer due to embedded USB interface on their printed circuit boards, and lack of SATA (or Parallel ATA) interfaces.[138][139] Visual representation

Hard disk drives are traditionally symbolized as a stylized stack of platters or as a cylinder, and are as such found in various diagrams; sometimes, they are depicted with small lights to indicate data access. In most modern graphical user environments (GUIs), hard disk drives are represented by an illustration or photograph of the drive enclosure.

In GUIs, hard disk drives are Two cylinders in a RAID diagram, commonly symbolized with a drive symbolizing an array of disks icon

See also

Automatic acoustic management Cleanroom Click of death Data erasure Drive mapping Microdrive RAID S.M.A.R.T. Solid-state drive Write precompensation Notes

a. This is the original filing date of the application which led to US Patent 3,503,060, generally accepted as the definitive disk drive patent.[1] b. Further terms used to describe hard disk drives include disk drive, disk file, direct access storage device (DASD), CKD disk, and Winchester disk drive (after the IBM 3340). The term "DASD" includes other devices beside disks. c. Comparable in size to a large side-by-side refrigerator. d. Initially gamma iron oxide particles in an epoxy binder, the recording layer in a modern HDD typically is domains of a granular Cobalt-Chrome-Platinum-based alloy physically isolated by an oxide to enable perpendicular recording.[18] e. Historically a variety of run-length limited codes have been used in magnetic recording including for example, codes named FM, MFM and GCR which are no longer used in modern HDDs. f. However, some enterprise SAS drives have other block sizes such as 520, 524 and 528 bytes, which can be changed in the field. g. Expressed using decimal multiples. h. Expressed using binary multiples. i. The International System of Units (SI), formerly known as the "metric system", does not define units for digital information but notes that the SI-defined prefixes (such as kilo, mega, etc.) may be applied outside the contexts where SI-defined base units or derived units would be used. j. Five platters for a conventional hard disk drive, and seven platters for a hard disk drive filled with Helium. k. Most common. l. This dimension includes a 0.5 mm protrusion of the Micro SATA connector from the device body. m. The Quantum Bigfoot TS used a maximum of three platters, other earlier and lower capacity product used up to four platters in a 5.25-inch HH form factor, e.g., Microscience HH1090 circa 1989. n. These differ from removable disk media, e.g., disk packs or data modules, in that they include, for example, actuators, drive electronics, motors. References

1. Kean, David W., "IBM San Jose, A quarter century of innovation", 1977. 2. Arpaci-Dusseau, Remzi H.; Arpaci-Dusseau, Andrea C. (2014). "Operating Systems: Three Easy Pieces [Chapter: Hard Disk Drives]" (http://pages.cs.wisc.edu/~remzi/OSTEP/file- disks.pdf) (PDF). Arpaci-Dusseau Books. 3. "IBM Archives: IBM 350 disk storage unit" (http://www- 03.ibm.com/ibm/history/exhibits/storage/storage_350.html). Retrieved 2012-10-19. 4. IDC report: Worldwide Disk Storage Systems Quarterly Tracker (2014-06-19). "Any Future for Worldwide Storage Industry?" (http://www.storagenewsletter.com/rubriques/market- reportsresearch/any-future-for-worldwide-storage-industry/). StorageNewsletter.com (Press release). IDC. Retrieved 2014-07-14. "Worldwide global disk storage systems revenue 2012 = $32,564 million; 2013 = $31,688 million" 5. Fullerton, Eric (March 2014). "5th Non-Volatile Memories Workshop (NVMW 2014)" (http://ieeemagnetics.org/files/IEEEMS-N-54-2-final.pdf) (PDF). IEEE. Retrieved April 23, 2014. 6. Handy, James (July 31, 2012). "For the Lack of a Fab..." (http://thessdguy.com/for-the-lack- of-a-fab/#more-538). Objective Analysis. Retrieved November 25, 2012. 7. Hutchinson, Lee. (2012-06-25) How SSDs conquered mobile devices and modern OSes (http://arstechnica.com/information-technology/2012/06/inside-the-ssd-revolution-mobile- devices-and-modern-oss/). Ars Technica. Retrieved on 2013-01-07. 8. Santo Domingo, Joel (May 10, 2012). "SSD vs HDD: What's the Difference?" (http://www.pcmag.com/article2/0,2817,2404258,00.asp). PC Magazine. Retrieved November 24, 2012. 9. "Time Capsule, 1956 Hard Disk" (http://www.oracle.com/technetwork/issue- archive/2014/14-jul/o44timecapsule-2219543.html). Oracle Magazine. Oracle. July 2014. Retrieved September 19, 2014. "IBM 350 disk drive held 3.75 MB" 10. "Toshiba Storage Solutions – MK3233GSG" (http://www.toshiba.co.jp/about/press/2009_11/pr0501.htm). 11. Ballistic Research Laboratories "A THIRD SURVEY OF DOMESTIC ELECTRONIC DIGITAL COMPUTING SYSTEMS," March 1961, section on IBM 305 RAMAC (http://www.ed- thelen.org/comp-hist/BRL61-ibm03.html#IBM-305-RAMAC) (p. 314-331) states a $34,500 purchase price which calculates to $9,200/MB. 12. "Farming hard drives: 2 years and $1M later" (https://www.backblaze.com/blog/farming- hard-drives-2-years-and-1m-later/). Backblaze Blog - The Life of a Cloud Backup Company. 13. "Magnetic head development" (https://www- 03.ibm.com/ibm/history/exhibits/storage/storage_magnetic.html). IBM Archives. Retrieved August 11, 2014. 14. "Seagate ST5000DM000 Desktop HDD Product Manual" (http://www.seagate.com/www- content/product-content/desktop-hdd-fam/en-us/docs/100743772a.pdf) (PDF). Seagate. Retrieved August 11, 2014. 15. Microsoft Windows NT Workstation 4.0 Resource Guide 1995, Chapter 17 – Disk and File System Basics 16. Computer Organization and Design, 2nd Ed., P. Pal Chaudhuri, 2006, p. 635 17. "Farming hard drives: how Backblaze weathered the Thailand drive crisis" (http://blog.backblaze.com/2012/10/09/backblaze_drive_farming/). blaze.com. 2013. Retrieved 2014-05-23. 18. New Paradigms in Magnetic Recording (http://arxiv.org/ftp/arxiv/papers/1201/1201.5543.pdf) 19. "Hard Drives" (http://www.escotal.com/harddrive.html). escotal.com. Retrieved 16 July 2011. 20. "What is a "head-crash" & how can it result in permanent loss of my hard drive data?" (http://www.data-master.com/HeadCrash-explain-hard-disk-drive-fail_Q18.html). data- master.com. Retrieved 16 July 2011. 21. "Hard Drive Help" (http://www.hard-drive-help.com/technology.html). hardrivehelp.com. Retrieved 16 July 2011. 22. Elert, Glenn. "Thickness of a Piece of Paper" (http://hypertextbook.com/facts/2001/JuliaSherlis.shtml). hypertextbook.com. Retrieved 9 July 2011. 23. CMOS-MagView (http://www.matesy.de/index.php? option=com_content&view=article&id=84&Itemid=80&lang=en) is an instrument that visualizes magnetic field structures and strengths. 24. Blount, Walker C. (November 2007). "Why 7,200 RPM Mobile Hard Disk Drives?" (https://web.archive.org/web/20120419091304/http://www.hitachigst.com/tech/techlib.nsf/t echdocs/33c6a76df9338b0a86256d34007054c0/$file/why7200mobilehdds.pdf) (PDF). Archived from the original (http://www.hitachigst.com/tech/techlib.nsf/techdocs/33c6a76df9338b0a86256d34007054c 0/%24file/why7200mobilehdds.pdf) (PDF) on 2012-04-19. Retrieved 17 July 2011. 25. "Ref — Hard Disk Spindle Motor" (http://www.pcguide.com/ref/hdd/op/spin_Speed.htm). PC Guide. Retrieved 2013-01-07. 26. Hayes, Brian. "Terabyte Territory" (http://www.americanscientist.org/issues/pub/terabyte- territory). Vol 90 (No 3 (May–June 2002)). American Scientist. p. 212. 27. "Press Releases December 14, 2004" (http://www.toshiba.co.jp/about/press/2004_12/pr1401.htm). Toshiba. Retrieved 13 March 2009. 28. "Seagate Momentus 2½" HDDs per webpage January 2008" (http://www.seagate.com/www/en-us/products/laptops/momentus/). Seagate.com. 24 October 2008. Retrieved 13 March 2009. 29. "Seagate Barracuda 3½" HDDs per webpage January 2008" (http://www.seagate.com/www/en-us/products/desktops/barracuda_hard_drives/). Seagate.com. Retrieved 13 March 2009. 30. "Western Digital Scorpio 2½" and Greenpower 3½" HDDs per quarterly conference, July 2007" (http://www.wdc.com/en/company/investor/q108remarks.asp). Wdc.com. Retrieved 13 March 2009. 31. Error Correcting Code (http://pcguide.com/ref/hdd/geom/errorECC-c.html), The PC Guide 32. Curtis E. Stevens (2011). "Advanced Format in Legacy Infrastructures: More Transparent than Disruptive" (http://www.idema.org/wp-content/uploads/downloads/2011/12/AF-in- Legacy-Infrastructures-SDC2011_IDEMA-AF.pdf) (PDF). idema.org. Retrieved 2013-11-05. 33. "Iterative Detection Read Channel Technology in Hard Disk Drives" (http://www.hitachigst.com/tech/techlib.nsf/techdocs/FB376A33027F5A5F8625750900146 3AE/$file/IDRC_WP_final.pdf), Hitachi 34. MjM Data Recovery Ltd. "MJM Data Recovery Ltd: Hard Disk Bad Sector Mapping Techniques" (https://web.archive.org/web/20140201174433/http://datarecovery.mjm.co.uk/sectorremap ping.html). Datarecovery.mjm.co.uk. Archived from the original (http://datarecovery.mjm.co.uk/sectorremapping.html) on 2014-02-01. Retrieved 2014-01-21. 35. Charles M. Kozierok. "The PC Guide: Hard Disk: Sector Format and Structure" (http://www.pcguide.com/ref/hdd/geom/tracks_Sector.htm). 1997–2004. 36. "Enterprise Performance 15K HDD: Data Sheet" (http://www.seagate.com/files/www- content/product-content/savvio-fam/enterprise-performance-15k-hdd/savvio-15k-4/en- us/enterprise-performance-15k-hdd-ds1797-1-1307us.pdf) (PDF). Seagate. 2013. Retrieved 2013-10-24. 37. "WD Xe: Datacenter hard drives" (http://www.wdc.com/wdproducts/library/SpecSheet/ENG/2879-771463.pdf) (PDF). Western Digital. 2013. Retrieved 2013-10-24. 38. "WD Re: Datacenter Capacity HDD" (http://www.wdc.com/wdproducts/library/SpecSheet/ENG/2879-771444.pdf) (PDF). Western Digital. 2013. Retrieved 2013-11-14. 39. "Cheetah 10K.7 FC Product Manual" (http://web.archive.org/web/20090612102811/http://www.seagate.com/staticfiles/support/d isc/manuals/enterprise/cheetah/10K.7/FC/100260916d.pdf) (PDF). Seagate. August 5, 2005. Archived from the original (http://www.seagate.com/staticfiles/support/disc/manuals/enterprise/cheetah/10K.7/FC/100 260916d.pdf) (PDF) on June 12, 2009. Retrieved August 29, 2013. 40. David S. H. Rosenthal (October 1, 2010). "Keeping Bits Safe: How Hard Can It Be?" (http://queue.acm.org/detail.cfm?id=1866298). ACM Queue. Retrieved 2014-01-02. 41. Whyte, Barry (September 18, 2009). "A brief History of Areal Density]" (https://www.ibm.com/developerworks/community/blogs/storagevirtualization/entry/a_brief _history_of_access_density1?lang=en). IBM DeveloperWorks. Retrieved July 25, 2014. 42. Walter, Chip (August 2005). "Kryder's Law" (http://www.scientificamerican.com/article.cfm? id=kryders-law). Scientific American. 43. "Gallium Arsenide" (http://www.pcmag.com/article2/0,2817,1172800,00.asp). PC Magazine. March 25, 1997. Retrieved August 16, 2014. "Gordon Moore: ... the ability of the magnetic disk people to continue to increase the density is flabbergasting--that has moved at least as fast as the semiconductor complexity." 44. Coughlin, Tom (2014-12-22). "HDD Areal Density And $/TB Trends" (http://www.forbes.com/sites/tomcoughlin/2014/12/22/hdd-areal-density-and-tb-trends/). Coughlin Associates www.tomcoughlin.com (Atascadero, CA: Forbes). Retrieved 2014-12-23. "graph is 5%/yr for 2011–2014. Current HDD areal density growth trends are in the range of 10% annually." 45. Mellor, Chris (2014-11-10). "Kryder's law craps out: Race to UBER-CHEAP STORAGE is OVER" (http://www.theregister.co.uk/2014/11/10/kryders_law_of_ever_cheaper_storage_disproven/ ). theregister.co.uk (UK: The Register). Retrieved 2014-11-12. "The 2011 Thai floods almost doubled disk capacity cost/GB for a while. Rosenthal writes: "The technical difficulties of migrating from PMR to HAMR, meant that already in 2010 the Kryder rate had slowed significantly and was not expected to return to its trend in the near future. The floods reinforced this."" 46. Rosenthal, David (2014-09-24). Moran, Nuala, ed. Economic Sustainability of Digital Preservation (http://www.eudat.eu/events/3rd-conference-sustainability-plenary). 3rd UPDATE Conference: Bringing data infrastructures to Horizon2020 (http://eudat.eu/3rd- eudat-conference). Amsterdam, The Netherlands: EUDAT European Data Infrastructure. p. 10. "Disk cost per byte: source Preeti Gupta, SSRC, UC Santa Cruz" 47. Gupta, Preeti; Wildani. "An Economic Perspective of Disk vs. Flash Media in Archival Storage" (http://www.digitalpreservation.gov/meetings/documents/storage14/Miller_economic- modeling-LoC14.pdf) (PDF). digitalpreservation.gov. Retrieved 2014-11-12. "disk cost per byte actual data points 1990–2013" 48. Dubash, Manek (2005-04-13). "Moore's Law is dead, says Gordon Moore" (http://news.techworld.com/operating-systems/3477/moores-law-is-dead-says-gordon- moore/). techworld.com. Archived (https://web.archive.org/web/20140706081110/http://news.techworld.com/operating- systems/3477/moores-law-is-dead-says-gordon-moore/) from the original on 2014-07-06. Retrieved 2014-08-17. "It can't continue forever. The nature of exponentials is that you push them out and eventually disaster happens." 49. Dave Anderson (2013). "HDD Opportunities & Challenges, Now to 2020" (https://www.dtc.umn.edu/resources/bd2013_anderson.pdf) (PDF). Seagate. Retrieved 2014-05-23. "PMR CAGR slowing from historical 40+% down to ~8-12%" and "HAMR CAGR = 20-40% for 2015–2020" 50. Plumer et. al, Martin L. (March 2011). "New Paradigms in Magnetic Recording" (http://arxiv.org/ftp/arxiv/papers/1201/1201.5543.pdf) (PDF). Physics in Canada 67 (1): 25– 29. Retrieved 17 July 2014. 51. "Seagate Delivers On Technology Milestone: First To Ship Hard Drives Using Next- Generation Shingled Magnetic Recording" (http://web.archive.org/web/20141009135540/http://www.seagate.com/about/newsroom/pr ess-releases/shingled-magnetic-recording-milestone-pr-master/) (Press release). New York, New York: Seagate Technology plc. seagate.com. 2013-09-09. Archived from the original (http://www.seagate.com/about/newsroom/press-releases/shingled-magnetic-recording- milestone-pr-master/) on 2014-10-09. Retrieved 2014-07-05. "Shingled Magnetic Technology is the First Step to Reaching a 20 Terabyte Hard Drive by 2020" 52. Jake Edge (2014-03-26). "Support for shingled magnetic recording devices" (https://lwn.net/Articles/591782/). LWN.net. Retrieved 2015-01-07. 53. Jonathan Corbet (2013-04-23). "LSFMM: A storage technology update" (https://lwn.net/Articles/548116/). LWN.net. Retrieved 2015-01-07. "A 'shingled magnetic recording' (SMR) drive is a rotating drive that packs its tracks so closely that one track cannot be overwritten without destroying the neighboring tracks as well. The result is that overwriting data requires rewriting the entire set of closely-spaced tracks; that is an expensive tradeoff, but the benefit—​much higher storage density—​is deemed to be worth the cost in some situations." 54. "Xyratex no-go for bit-patterned media" (http://www.theregister.co.uk/2010/05/24/xyratex_hamr/). The Register. 24 April 2010. Retrieved 21 August 2010. 55. "Report: TDK Technology "More Than Doubles" Capacity Of HDDs" (http://techcrunch.com/2011/10/04/report-tdk-technology-more-than-doubles-capacity-of- hdds/? utm_source=feedburner&utm_medium=feed&utm_campaign=Feed%3A+Techcrunch+%2 8TechCrunch%29). Retrieved 4 October 2011. 56. Mallary et. al, Mike (July 2014). "Head and Media Challenges for 3 Tb/in2 Microwave- Assisted Magnetic Recording". IEEE TransMag (IEEE) 50 (7): 3001008. 57. Wood, Roger (2010-10-19). "Shingled Magnetic Recording and Two-Dimensional Magnetic Recording" (http://www.ewh.ieee.org/r6/scv/mag/MtgSum/Meeting2010_10_Presentation.pdf) (PDF). ewh.ieee.org. Hitachi GST. Retrieved 2014-08-04. 58. "Will Toshiba's Bit-Patterned Drives Change the HDD Landscape?" (http://www.pcmag.com/article2/0,2817,2368023,00.asp). PC Magazine. 19 August 2010. Retrieved 21 August 2010. 59. Coughlin, Thomas; Grochowski, Edward (19 June 2012). "Years of Destiny: HDD Capital Spending and Technology Developments from 2012–2016" (http://ewh.ieee.org/r6/scv/mag/MtgSum/Meeting2012_06_Presentation.pdf) (PDF). IEEE Santa Clara Valley Magnetics Society. Retrieved 9 October 2012. 60. All-Heusler giant-magnetoresistance junctions with matched energy bands and Fermi surfaces (http://arxiv.org/ftp/arxiv/papers/1301/1301.6106.pdf) 61. "Perpendicular Magnetic Recording Explained - Animation" (http://www1.hgst.com/hdd/research/recording_head/pr/PerpendicularAnimation.html). 62. Raymond, Robert M. (2013-09-09). "Current and Emerging Storage Technologies iCAS2013" (https://www2.cisl.ucar.edu/sites/default/files/Raymond.pdf) (PDF). In Mahoney III, William P. Storage Technologies Areal Density Trends. International Computing for the Atmospheric Sciences Symposium (iCAS2013) (https://www2.cisl.ucar.edu/cas2k13). Annecy, France: ORACLE Corp. at National Center for Atmospheric Research under sponsorship from the U.S. National Science Foundation. "page 11: Areal Density (Gbits/in^2) HDD Products 2010–2022 10-20%/year?" 63. "HDD Areal Density Doubling in Five Years" (http://www.storagenewsletter.com/rubriques/market-reportsresearch/ihs-isuppli-storage- space/) (Press release). IHSi iSuppli Research. storagenewsletter.com. 2012-05-24. Retrieved 2014-05-31. "from 2011 to 2016, the five-year CAGR for HDD areal densities will be equivalent to 19%" 64. Fontana, R.; Decad, G.; Hetzler, S. (2012-09-20). "Technology Roadmap Comparisons for TAPE, HDD, and NAND Flash: Implications for Data Storage Applications" (http://www.digitalpreservation.gov/meetings/documents/storage12/5-Fontana- StorageMediaDenstiyfoRNANDTAPE.pdf) (PDF). digitalpreservation.gov (Washington D.C.: The Library of Congress). p. 18. Retrieved 2014-07-05. "Annual Areal Density Growth Rate Scenarios: HDD 20%/yr 2012–2017" 65. Kaur, Simran (2014-09-15). "Seagate treads safely in uncertain demand environment; narrow moat has negative trend." (http://analysisreport.morningstar.com/stock/research? t=STX®ion=usa&culture=en-US&productcode=MLE). Morningstar. Retrieved 2014-09-26. "a slowing areal density curve … that slowed around 2010 and will advance areal density 25% annually till 2020." 66. Information technology – Serial Attached SCSI – 2 (SAS-2), INCITS 457 Draft 2, 8 May 2009, chapter 4.1 Direct-access block device type model overview, "The LBAs on a logical unit shall begin with zero and shall be contiguous up to the last logical block on the logical unit." 67. ISO/IEC 791D:1994, AT Attachment Interface for Disk Drives (ATA-1), section 7.1.2 68. "How to Measure Storage Efficiency – Part II – Taxes" (https://web.archive.org/web/20110720131225/http://blogs.netapp.com/efficiency/2009/08/ measuring-storage-efficiency-part-ii-taxes.html). Blogs.netapp.com. 14 August 2009. Archived from the original (http://blogs.netapp.com/efficiency/2009/08/measuring-storage- efficiency-part-ii-taxes.html) on 2011-07-20. Retrieved 26 April 2012. 69. "Western Digital's Advanced Format: The 4K Sector Transition Begins" (http://www.anandtech.com/show/2888). Anandtech.com. Retrieved 26 April 2012. 70. "Low-Level Formatting" (http://www.pcguide.com/ref/hdd/geom/formatLow-c.html). 71. "High-Level Formatting" (http://www.pcguide.com/ref/hdd/geom/formatHigh-c.html). Pcguide.com. 17 April 2001. Retrieved 26 April 2012. 72. "Storage Solutions Guide" (https://web.archive.org/web/20130620212124/http://www.seagate.com/files/www- content/partners/my%20spp%20dashboard/learn/en-us/docs/amer-stx-storage-solutions- guide-Oct-2012.pdf) (PDF). Seagate. October 2012. Archived from the original (http://www.seagate.com/files/www-content/partners/my%20spp%20dashboard/learn/en- us/docs/amer-stx-storage-solutions-guide-Oct-2012.pdf) (PDF) on 2013-06-20. Retrieved June 8, 2013. 73. "MKxx33GSG MK1235GSL r1" (http://sdd.toshiba.com/techdocs/MKxx33GSG_MK1235GSL_r1.pdf) (PDF). Toshiba. Retrieved 2013-01-07. 74. "Drive displays a smaller capacity than the indicated size on the drive label" (http://wdc.custhelp.com/app/answers/detail/a_id/615/session/L2F2LzIvc25vLzEvdGltZS8x MzAyMjgxMDM1L3NpZC9NRjNaWFpxaw%3D%3D). Wdc.custhelp.com. 29 March 2012. Retrieved 26 April 2012. 75. "HGST" (http://www.hitachigst.com/tech/techlib.nsf/techdocs/B259B4A73296DA628625751600058 A80/$file/ProductBrochureMarch2009.pdf) (PDF). Retrieved 2013-06-08. 76. "Samsung" (http://www.samsung.com/global/business/hdd/faqView.do? b2b_bbs_msg_id=167). Samsung Hard Drives. Retrieved 2013-06-08. 77. "Toshiba" (http://sdd.toshiba.com/techdocs/MKxx33GSG_MK1235GSL_r1.pdf) (PDF). Retrieved 2013-06-08. 78. "Western Digital" (http://www.wdc.com/en/library/2579-001028.pdf) (PDF). Wdc.com. Retrieved 2013-06-08. 79. "650 RAMAC announcement" (http://www- 03.ibm.com/ibm/history/exhibits/650/650_pr2.html). 80. Mulvany, R.B., "Engineering Design of a Disk Storage Facility with Data Modules". IBM JRD, November 1974 81. Introduction to IBM Direct Access Storage Devices, M. Bohl, IBM publication SR20-4738. 1981. 82. CDC Product Line Card (http://www.bitsavers.org/pdf/cdc/discs/brochures/ProductLine_Oct74.pdf), October 1974 83. Apple Support Team. "How OS X and iOS report storage capacity" (https://support.apple.com/en-us/HT201402). Apple, Inc. 84. "Western Digital Settles Hard-Drive Capacity Lawsuit, Associated Press 28 June 2006 retrieved 25 November 2010" (http://www.foxnews.com/story/0,2933,201269,00.html). Fox News. 22 March 2001. Retrieved 26 April 2012. 85. Published on 26 October 2007 by Phil Cogar (26 October 2007). "Seagate lawsuit concludes, settlement announced" (http://www.bit- tech.net/news/bits/2007/10/26/seagate_lawsuit_concludes_settlement_announced/1). Bit- tech.net. Retrieved 26 April 2012. 86. "Western Digital – Notice of Class Action Settlement email" (http://www.xtremesystems.org/forums/showthread.php?t=93512). Xtremesystems.org. Retrieved 26 April 2012. 87. "8TB HDD Now Shipping ..." (http://www.hgst.com/press-room/press-releases/HGST-unveils- intelligent-dynamic-storage-solutions-to-transform-the-data-center). 2014. Retrieved October 13, 2014. 88. "Ultrastar He6: 6TB 3.5-inch Helium Platform Enterprise Hard Drive" (http://www.hgst.com/hard-drives/enterprise-hard-drives/enterprise-sas-drives/ultrastar- he6). hgst.com. 2013. Retrieved 2013-12-06. 89. "Western Digital builds 5mm-thick hybrid hard drive, Ultrabook makers sign on early" (http://www.engadget.com/2012/09/10/western-digital-builds-5mm-thick-hybrid-hard- drive/). Engadget. Retrieved 2013-01-07. 90. "Quantum Go*Drive specifications" (http://www.4drives.com/DRIVESPECS/QUANTUM/3364.txt). 4drives.com. Retrieved 2014-05-22. 91. "Western Digital WD20NPVX Specifications" (http://www.wdc.com/en/products/products.aspx?id=830#Tab3). Wdc.com. Retrieved 2014-09-10. 92. "Samsung M9T Mobile SATA Drive Datasheet" (http://www.seagate.com/www- content/support-content/samsung/internal-products/spinpoint-m-series/en-us/samsung- m9t-internal-ds.pdf) (PDF). 93. "Toshiba MK2239GSL, 220 GB single-platter HDD" (http://storage.toshiba.com/techdocs/MKxx39GSL_Data_Sheet.pdf) (PDF). 94. Seagate Elite 47, shipped 12/97 per 1998 Disk/Trend Report – Rigid Disk Drives 95. Quantum Bigfoot TS, shipped 10/98 per 1999 Disk/Trend Report – Rigid Disk Drives 96. "SDK Starts Shipments of 1.3-Inch PMR-Technology-Based HD Media" (https://web.archive.org/web/20090316121840/http://www.sdk.co.jp/aa/english/news/2008/ aanw_08_0812.html). Sdk.co.jp. 10 January 2008. Archived from the original (http://www.sdk.co.jp/aa/english/news/2008/aanw_08_0812.html) on 2009-03-19. Retrieved 13 March 2009. 97. "Proving that 8 GB, 0.85 inch hard disk drive exists" (http://digitaljournal.com/article/117340). Digitaljournal.com. 17 February 2007. Retrieved 26 April 2012. 98. "Toshiba Enters Guinness World Records Book with the World's Smallest Hard Disk Drive" (http://www.toshiba.co.jp/about/press/2004_03/pr1601.htm). Toshiba Corp. 16 March 2004. Retrieved 11 September 2012. 99. Emerson W. Pugh, Lyle R. Johnson, John H. Palmer IBM's 360 and early 370 systems MIT Press, 1991 ISBN 0-262-16123-0, page 266 100. Christensen, Clayton M. (1997). The Innovator's Dilemma. New York, New York: HarperBusiness. pp. 19–252. ISBN 0-06-662069-4. 101. "SFF-8500 Specification for Suite of 5.25" Form Factor Specifications" (ftp://ftp.seagate.com/sff/SFF-8500.PDF) (PDF). SFF Committee. June 5, 1995. Retrieved 2014-02-01. 102. "Winchester has 3.5-inch diameter". Electronics: 184. March 1983. 103. "SFF-8301 Specification for Form Factor of 3.5" Disk Drives" (ftp://ftp.seagate.com/sff/SFF- 8301.PDF) (PDF). SFF Committee. February 8, 2013. Retrieved 2014-02-01. 104. Chandler, Doug (26 September 1988). "Startup Ships 2.5-Inch Hard Disk Aimed for Portables, Laptops". PC Week: 6. 105. "SFF-8201 Specification for Form Factor of 2.5" Disk Drives" (ftp://ftp.seagate.com/sff/SFF- 8201.PDF) (PDF). SFF Committee. October 28, 2013. Retrieved 2014-02-01. 106. Schmid, Patrick and Achim Roos (8 May 2010). "3.5" Vs. 2.5" SAS HDDs: In Storage, Size Matters" (http://www.tomshardware.co.uk/enterprise-storage-sas-hdd,review-31891.html). Tomshardware.com. Retrieved 25 June 2010. 107. "PlayStation 3 Slim Teardown" (http://www.ifixit.com/Teardown/PlayStation-3-Slim/1121/1). 25 August 2009. Retrieved 15 November 2010. 108. Schmid, Patrick and Achim Roos (22 May 2010). "9.5 Versus 12.5 mm: Which Notebook HDD Is Right For You?" (http://www.tomshardware.com/reviews/2.5-inch-12.5-mm-9.5- mm,2623.html). Tomshardware.com. Retrieved 22 June 2010. 109. "Seagate Unveils World's Thinnest 2.5-Inch Hard Drive For Slim Laptop Computers" (http://www.physorg.com/news180118264.html). physorg.com. 15 December 2009. Retrieved 15 December 2009. 110. Ian Paul (23 April 2013). "Western Digital rolls out ultra-slim 5 mm Ultrabook drives." (http://www.pcworld.com/article/2036197/western-digital-rolls-out-ultra-slim-5mm- ultrabook-drives.html). PCWorld. 111. "World HDD Market: Key Research Findings 2010" (http://www.yanoresearch.com/press/pdf/718.pdf) (PDF). Yano Research Institute. December 15, 2010. Retrieved October 16, 2012. 112. "Specification for 1.8" (60x70mm) w/Serial Attachment Connector, Rev C" (ftp://ftp.seagate.com/sff/SFF-8123.TXT) (PDF). SFF Committee. January 2005. Retrieved 2014-02-01. 113. 1.3" HDD Product Specification (http://www.samsung.com/global/system/business/hdd/prdmodel/2008/1/25/2469101.3_Inc h_Spec_PATA_rev.2.3.pdf), Samsung, 2008 114. Toshiba's 0.85-inch HDD is set to bring multi-gigabyte capacities to small, powerful digital products (http://www.toshiba.co.jp/about/press/2004_01/pr0801.htm), Toshiba press release, 8 January 2004 115. "Toshiba Storage Device Division Overview" (http://storage.toshiba.com/techdocs/ToshibaSDDCorpBackgrounder.pdf) (PDF). Retrieved 2013-06-08. 116. Toshiba enters Guinness World Records Book with the world's smallest hard disk drive (http://www.toshiba.co.jp/about/press/2004_03/pr1601.htm), Toshiba press release, 16 March 2004 117. Flash price fall shakes HDD market (http://www.eetasia.com/ART_8800474064_499486_NT_3335be30.HTM), EETimes Asia, 1 August 2007. 118. In 2008 Samsung (http://www.samsung.com/global/business/hdd/newsView.do? b2b_bbs_msg_id=143) introduced the 1.3-inch SpinPoint A1 HDD but by March 2009 the family was listed as End Of Life Products (http://www.samsung.com/global/business/hdd/products/Product_EOLProducts.html) and new 1.3-inch models were not available in this size. 119. "Western Digital definition of Average Access Time" (http://www.wdc.com/en/company/glossaryofterms/wdglossarycontent.asp). Wdc.com. 1 July 2006. Retrieved 26 April 2012. 120. Kearns, Dave (18 April 2001). "How to defrag" (http://www.itworld.com/NWW01041100636262). ITWorld. 121. Broida, Rick (10 April 2009). "Turning Off Disk Defragmenter May Solve a Sluggish PC" (http://www.pcworld.com/article/162955/turning_off_disk_defragmenter_may_solve_a_slugg ish_pc.html). PCWorld. 122. Anand Lal Shimpi (2010-04-06). "Western Digital's New VelociRaptor VR200M: 10K RPM at 450GB and 600GB" (http://www.anandtech.com/show/3636/western-digitals-new- velociraptor-vr200m-10k-rpm-at-450gb-and-600gb). anandtech.com. Retrieved 2013-12-19. 123. "WD Scorpio Blue Mobile: Drive Specifications" (http://www.wdc.com/en/products/products.aspx?id=140). Western Digital. June 2010. Retrieved 15 January 2011. 124. "IBM Archives: IBM 3350 direct access storage" (http://www- 03.ibm.com/ibm/history/exhibits/storage/storage_3350.html). IBM. Retrieved 2013-01-07. 125. ""Speed Considerations"" (https://web.archive.org/web/20110210155634/http://www.seagate.com/www/en- us/support/before_you_buy/speed_considerations). Seagate. Archived from the original (http://www.seagate.com/www/en-us/support/before_you_buy/speed_considerations) on 2011-02-10. Retrieved 22 January 2011. 126. ""Reed Solomon Codes – Introduction"" (https://web.archive.org/web/20110708040145/http://gaussianwaves.blogspot.com/2008/06 /reed-solomon-codes-introduction.html). Archived from the original (http://gaussianwaves.blogspot.com/2008/06/reed-solomon-codes-introduction.html) on 8 July 2011. 127. "Micro House PC Hardware Library Volume I: Hard Drives, Scott Mueler, Macmillan Computer Publishing" (http://www.alasir.com/books/hards/022-024.html). Alasir.com. Retrieved 26 April 2012. 128. "Ruggedized Disk Drives for Commercial Airborne Computer Systems" (http://apex.aero/Portals/0/harddisk.pdf) (PDF). (http://apex.aero/Portals/0/harddisk.pdf) (PDF). 129. Grabianowski, Ed. "How To Recover Lost Data from Your Hard Drive" (http://electronics.howstuffworks.com/how-to-tech/how-to-recover-data-hard-drive4.htm). HowStuffWorks. pp. 5–6. Retrieved 24 October 2012. 130. "Everything You Know About Disks Is Wrong" (http://storagemojo.com/2007/02/20/everything-you-know-about-disks-is-wrong/). Storagemojo.com. 2007-02-22. Retrieved 2010-08-24. 131. Eduardo Pinheiro, Wolf-Dietrich Weber and Luiz André Barroso (February 2007). "Failure Trends in a Large Disk Drive Population" (http://research.google.com/archive/disk_failures.pdf) (PDF). Google Inc. Retrieved 2011-12-26. 132. Investigation: Is Your SSD More Reliable Than A Hard Drive? (http://www.tomshardware.com/reviews/ssd-reliability-failure-rate,2923-9.html) – Tom's Hardware long term SSD reliability review, 2011, "final words" 133. Broekhuijsen, Niels (2014-08-26). "Seagate 8 TB HDDs Widely Available Next Quarter, Shipping Now" (http://www.tomshardware.com/news/seagate-8tb-hard-drive- hdd,27544.html). Tom's Hardware (US: Purch). Retrieved 2014-08-26. 134. "Enterprise-class versus Desktop class Hard Drives" (http://download.intel.com/support/motherboards/server/sb/enterprise_class_versus_deskto p_class_hard_drives_.pdf) (PDF). Intel. Retrieved 25 September 2013. 135. Seagate Cheetah 15K.5 Data Sheet (http://www.seagate.com/docs/pdf/marketing/po_cheetah_15k_5.pdf) 136. Martin K. Petersen (2008-08-30). " Data Integrity" (http://web.archive.org/web/20150109235547/https://oss.oracle.com/~mkp/docs/lpc08- data-integrity.pdf) (PDF). Oracle Corporation. Archived from the original (https://oss.oracle.com/~mkp/docs/lpc08-data-integrity.pdf) (PDF) on 2015-01-09. Retrieved 2015-01-23. "Most disk drives use 512-byte sectors. [...] Enterprise drives (Parallel SCSI/SAS/FC) support 520/528 byte 'fat' sectors." 137. "Back Up Your Important Data to External Hard disk drive | Biometric Safe | Info and Products Reviews about Biometric Security Device –" (https://web.archive.org/web/20120525025411/http://biometricsecurityproducts.org/biome tric-safe/back-up-your-important-data-to-external-hard-disk-drive.html). Biometricsecurityproducts.org. 26 July 2011. Archived from the original (http://biometricsecurityproducts.org/biometric-safe/back-up-your-important-data-to- external-hard-disk-drive.html) on 2012-05-25. Retrieved 26 April 2012. 138. "Western Digital My Passport, 2 TB" (http://content.hwigroup.net/images/products/xl/152766-7.jpg). hwigroup.net. Retrieved 2014-01-11. "Example of a pre-assembled external hard disk drive without its enclosure that cannot be used internally on a laptop or desktop due to the embedded interface on its printed circuit board" 139. Sebean Hsiung (2010-05-05). "How to bypass USB controller and use as a SATA drive" (http://www.datarecoverytools.co.uk/2010/05/05/how-to-connect-and-recover--only- western-digital-drives-with-hd-doctor-suite/). datarecoverytools.co.uk. Retrieved 2014-01-11. Further reading

Mueller, Scott (2011). Upgrading and Repairing PCs (20th ed.). Que. ISBN 0- 7897-4710-3. Messmer, Hans-Peter (2001). The Indispensable PC Hardware Book (4th ed.). Addison-Wesley. ISBN 0-201-59616-4. External links

Computer History Museum's HDD Working Group Website (http://chmhdd.wetpaint.com/) Hard Disk Drives Encyclopedia (http://www.smarthdd.com/en/help.htm) Video showing an opened HD working (http://www.engineerguy.com/videos/video-harddrive.htm) Average seek time of a computer disk (http://faculty.plattsburgh.edu/jan.plaza/teaching/papers/seektime.html) Timeline: 50 Years of Hard Drives (http://www.pcworld.com/article/127105/article.html) HDD from inside: Tracks and Zones. How hard it can be? (http://hddscan.com/doc/HDD_Tracks_and_Zones.html) Hard disk hacking (https://spritesmods.com/?art=hddhack) – firmware modifications, in eight parts, going as far as booting a Linux kernel on an ordinary HDD controller board Hiding Data in Hard Drive’s Service Areas (http://www.recover.co.il/SA- cover/SA-cover.pdf), February 14, 2013, by Ariel Berkman Rotary Acceleration Feed Forward (RAFF) Information Sheet (http://www.wdc.com/wdproducts/library/other/2579-001079.pdf), Western Digital, January 2013 Time-Limited Error Recovery (TLER) Information Sheet (http://www.wdc.com/wdproducts/library/other/2579-001098.pdf), Western Digital, January 2013 PowerChoice Technology for Hard Disk Drive Power Savings and Flexibility (http://www.seagate.com/files/docs/pdf/en-GB/whitepaper/tp608- powerchoice-tech-provides-gb.pdf), Seagate Technology, March 2010

Retrieved from "http://en.wikipedia.org/w/index.php? title=Hard_disk_drive&oldid=666141997"

Categories: American inventions Computer peripherals Computer storage devices Computer storage media File system management Hard disk drives Non-

This page was last modified on 9 June 2015, at 05:13. Text is available under the Creative Commons Attribution-ShareAlike License; additional terms may apply. By using this site, you agree to the Terms of Use and Privacy Policy. Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a non-profit organization.