GOVERNMENT OF PUBLIC WORKS DEPARTMENT Office of the Assistant Engineer (P.W.D) Krishnagar Construction Sub-Division No-III Arabindo Sarani, P.O.—Krishnagar, Dist.—Nadia. NOTICE INVITING TENDER

TENDER NOTICE NO. 06/KC-III of 2020-2021 Sealed Tenders in specified printed form are invited for the following work(s) from reliable, resourceful experienced and bonafied Contractors who may be found eligible after scrutiny of their credentials to be submitted as per particulars given below and will be received by the Assistant Engineer, Krishnagar Construction Sub-Division –III, P.W.D in the tender box in his chamber or as stated otherwise. Upto specified date and time and will be opened half an hour later on the same date of later as will be notified, in presence of contractors or their authorized representatives who may to be present at time of opening.

1) Name of work : As per Annexure – I

2) Name of Construction Sub-Division : Krishnagar Construction Sub-Division III

3)Estimated Amount Put to Tender : As per Annexure - I

4) Location of Godown : Krishnagar/Santipur/

5) Time allotted for completion of work : As per Annexure - I

6)Contractor Eligibility in submit Ten :- OPEN TENDER

7) Eligibility criteria to participate The willing contractors will have to apply for participation in the In the tender tender in their printed letter head containing full mailing address withpresent telephone number ( Mobile No. & Land Line No. if any) along with required documents (self Attested) as mentioned herein below. On scrutiny of the required documents and after verification of the same with the original, if the agency is found to be eligible necessary certificate ofeligibility shall be issued by the tender inviting authority to the concerned agency himself or his representative The “Certificate of Eligibility” thus issued to the agencyshall have to be submitted in sealed cover along with the tender documents & EMD. (Original are to be shown for verification by this office at the time of scrutinizing application).

Documents to be furnished for participating in the tender:-

i) Valid PAN card. Trade License and Professional Tax Clearance Certificates. GST Registration Certificate, Plumbing License (In case of S & P work) II) Bye Laws, PAN card , Professional Tax Clearance Certificates, GST Registration Certificate, Last year audit report for Un-employed Engineer’s/Labour Co-Opt. Society Ltd. III)At least 40 % Credentials in support of Experience certificate/proof of Executing satisfactorily completed at least one single job of similar nature under Govt. of West Bengal / Central Govt. during last 5 (five) years from the date of issue of this notice. (Work order will not be entertained). 8) Earnest Money Rs: As per Annexure - I (To be deposited in the shape of Bank Draft in favour of Executive Engineer P.W.D, Nadia Construction Division.( from any Nationalized Bank) 9) Applicable Schedule of Rates : P.W.D.(W.B) Schedule of rates applicable for central Circle (Nadia) and on Date of N.I.T. both Building and S & P 10) Last Date and time for receipt of application for Participation. (off line) in the tender. :On 02.11.2020 Up to 2.00 p.m. 11) Last Date and time of issuing permission certificate to Technically Eligible Bidders to participate in Tender. : On 04.11.2020 Up to 2.00 p.m. N.I.T Special Terms and Conditions, Specified tender forms-2911, price 12) Availability of Tender Documents ( On Line) : will be available and/for downloaded from the Departmental Website (http://www.pwdwb.in) at Free of Cost.

13) Last date and time for receipt of tender papers in Sealed cover. (off line) along with original permission certificate and EMD. : On 06.11.2020 Up to 2.00 p.m. (In the tender Box kept in the Chamber of Assistant Engineer, Krishnagar, Construction Sub-Division No-III, P.W.D)

14) Date & time of opening of tender : On 06.11.2020 at 3:30 p.m.

Note: Tenderer shall have to write Tender Notice No., Name of Tenderer on the body of sealed cover, otherwise the bid shall be liable to be rejection at the time of opening Tender. 15) No exemption of Earnest Money Deposit will be entertained for any Bidder and/ or any case.

16) The tender documents and other relevant particulars (if any) may be seen by the intending tenderer during office hours in the office of the undersigned between 11.00 am to 4.00 pm on any working day up to last date of application.

17) Validity of the tender : The offer will remain valid for acceptance for 120 days from the date of receipt of tender.

18) The contractors should quote in his own writing in figure as well as in words the rate in percentage AT PAR/ ABOVE / BELOW on the basis of the priced Schedule of probable items with approximate quantities. The contractors may sign either in English, Bengali or Hindi but the rates as above should also be quoted in the same languages. In case of illiterate contractors the rate tendered for should be attested by a witness.

19) Conditional Tender will be liable for rejection.

20) Time/Cost over-run and consequent cost escalation for any material, labour, POL etc. will not be allowed.

21) No mobilization advance / secured advance will be allowed.

22) Even after submission of tender, the tender will not be taken into consideration during evaluation, if the papers submitted by any agency in support of eligibility are found to be baseless/false in the event of verification from the concerned authority.

23) In case of non-participation in the tender in any shape will be dealt severely for making an attempt towards disruption of competitive spirit of tender and non- participant may be disallowed to participate in 3 (three) nos. consecutive N.I.T of this Sub Division.

24) A CESS of 1% of the cost of construction works will be deducted from the bills of the contractors and remit the amount so collected to the " W.B. Building and other Construction Workers Welfare Board" as notification No. 1182 IR dated 20.09.2005 of the Labour Department.

25) If any contractors fails to start the work within 7 (seven) days from issuing date of work order / Formal tender the work order will be cancelled and relevant clauses of the condition of the contract shall deemed to have executed by the tendering authority. No litigation to this effect shall be entertained by the tender inviting authority, this is incorporated to deliver time bound Public works.

26) Tender inviting Authority reserves the right to issue corrigendum towards the estimated amount, eligibility of contractors, Earnest money, time of completion etc. in case of any revision, three days in advance to the date of application under certain unavoidable circumstances. 27) In case of inadvertent typographical mistake found in the specific price schedule of rates, the same will be treated to be so corrected as to conform to the prevailing relevant schedule of rates and / or technically sanctioned estimate.

28) In case of any Bandh or Holiday or Natural Calamity on the aforesaid dates, the next working day will be treated as scheduled/prescribed date for the purpose.

29) The payment will be made as and when fund will be available from the concerned source. No Claim , whatsoever, for delay in payment, if any will be entertained. Contractors are requested to quote their rate accordingly.

30) Tender inviting Authority reserves his right to rectify /replace/substitute any rate of the priced schedule put to tender in case of any inadvertent /typographical mistake both in figure as well as in words prior to execution of formal Tender.

31)The bills are to be submitted to the office of the Assistant Engineer/Krishnagar Construction Sub Division No - III, PWD by the concerned Sub Assistant Engineer (P.W.D)/Krishnagar Construction Sub-Division –III with the consumption statement of materials and plants & machineries even Up to date issued to the agency. The Executive Engineer (P.W.D) Nadia Construction Division , will make payment subject to the availability of LOC. The progress of work in this connection will not be hampered due to the delayed payment or due to any other reasons.

32) Necessary mandatory deduction towards I.T, SGST/CGST/IGST etc will be made as per relevant Govt. orders.

33) The successful tenderer will have to execute formal agreement as within specified time period as per instruction from this end and during execution of formal agreement price of tender documents accompanied with the cost Tender Form No.2911/2911(i)/2911(ii) & price schedule will have to be paid by the successful Tenderer.

34) Issuance of particular tender to any contractor will be mainly on the merit of documents submitted and other consideration regarding reliability and resourcefulness. Technically qualified agency as allowed by the Tender inviting authority shall be allowed to submit the tender documents (Price Bid) in the Tender Box kept in the chamber of the Tender inviting authority along with certificate of eligibility to be received from the office of the Tender inviting authority along with EMD. The discretion of the tender inviting authority in granting permission cannot be challenged.

35) There shall be no provision of Arbitration. Hence clause 25 of WB Form No.2911 is omitted vide Notification No. 558/SPW dated. 13/12/2011 of Principal Secretary, P.W. & P.W. (Roads) Department. It's also informed to all bidders that , The clause 17 of WB Form 2911(ii) {Liability of contractor for damaged done & for imperfection} is partially modified vide Notification No. 177-CRC/2M-57/2008 dated 12/07/2012 of the secretary to the Government of West Bengal.

36) Assistant Engineer(P.W.D), Krishnagar Construction Sub Division No. III, may invite fresh Bid (Open or Sealed) if necessary, among the respective tenderers, after tenders are opened or on the 3rd working day after the date of opening tenders. . 37) Payments for works may be delayed due to non availability of fund for which no claim would be entertained. Completion of work may not suffer for any non-payment or delay in payment.

38) The successful contractors will have to abide by the provision the West Bengal Contract Labour (Regulation and Abolition ) Rules, 1972 and obtain License from the appropriate authority as per said Act. And Rules , if applicable in this case.

39) In case of partnership firm, the intending tenderer shall have to produce authentic document in respect of firm registration obtained from the Registrar of Firms. West Bengal Pursuant to the Indian Partnership Act 1932 (Act IX of 1932).

40) No credential will be considered unless it is supported by payment certificate, work – order and completion certificate mentioning the date of completion issued by the competent authority not below the rank of Executive Engineer or Similar rank. Priced Schedule of the work should also be submitted at the time of submission of application so that the quantum of similar nature of work may be verified before issue of tender paper. If due to ambiguity, quantum of similar nature of work cannot be ascertained clearly from completion certificate / credential documents, it will be verified from the price schedule of work. 41) Periodical quality test of materials supplied by the agency and final products are to be made as per guidance of schedule of P.W.D/I.S/I.R.S/M.O.R.T. & H at contractor’s cost. Normally quality control test of supplied materials / final products will be done in the Departments Laboratory. Otherwise testing of materials/final products will be done from the outside recognized laboratory at the discretion of Engineer- in-charge. In both the cases necessary cost of testing charges will be borne by the agency.

41) All tenderer or his authorized representative is required to requested to present personally during the opening of the tender and to sign tender opening register as witness.

42) No, person will be allowed to quote rate on the basis of Legal Power of Attorney conferred to him by the Firm/ Agency except in circumstances where necessary Govt. approval has been obtained.

S/d- A. Mitra

Assistant Engineer(P.W.D) Krishnagar Construction Sub. Division-III

Memo No. :- 300(12) Dated: 13.10.2020

Copy forwarded for information and wide circulation to:- 1)The Superintending Engineer ,Central Circle, P.W.D, Berhampore, Murshidabad. 2)The Executive Engineer(P.W.D), Nadia Construction Division ,Krishnagar, Nadia,vide his Memo. No.1838 dated-08.09.2020.& 2038 dated 29.09.2020.. 3)The Executive Engineer(P.W.D),Nadia Division, Krishnagar,Nadia. 4)The Sabhadhipati, Nadia ZillaParishad. 5)The District Magistrate, Nadia. 6) The Assistant Engineer(P.W.D), Ranaghat Sub- Division, Ranaghat, Nadia 7)The Assistant Engineer (P.W.D) ,Krishnagar Sub-Division (P.W.D) 8)The Assistant Engineer (P.W.D),Krishnagar Construction Sub-Division No-I 9)The Assistant Engineer (P.W.D),Krishnagar Construction Sub-Division-II 10) Nadia Progressive Contractor Welfare Association, Krishnagar, Nadia. 11) District Information Cultural Officer, Nadia ,Krishnagar, for information and necessary action please. 12) Notice Board of Krishnagar Construction Sub-Division No III.

S/d- A. Mitra

Assistant Engineer(P.W.D) Krishnagar Construction Sub. Division-III ANNEXURE - I

List of works for N.I. T. No .06/ K.C -III of 2020-2021 of Assistant Engineer (P.W.D.) Krishnagar Construction Sub Division. No. III for 2(two) nos works

Sl. Name of Works Estimated Earnest Cost of W.B. F. 2911(II) and Eligibility of Contractors Time of Remarks No. amount put money in other documents Completion to Tender in Rs. Rs.

1 2 3 4 5 6 7 8

.

1. Toe protection work at approach of existing Rs.5.00=00 &750.00 Bonafied resourceful contractors concrete road from Gouranga Setu towards Total Rs. 755.00.Each. preferable similar nature of 20 (twenty) Sanskrito Sahitya Charcha O Gabeshana Kendra from Rs-3,99,740.00 Rs. 7,995.00. completed work of the minimum Days No fees to be deposited by value of 40% of the estimated 0.100 K.M. to 0.175 Km. with 10 cm dia Eucalyptus the bidder initially but to be amount put to tender during 5 (five) ballah pilling along with Dram sheet walling under submitted by lowest bidder on years prior to the date of issue of Nadia Construction Division during the year 2020- demand. the tender notice& as per G.O. 2021.

2. Setting up of Vice-Chancellor, Kanyashree Universitys Chamber, MIS Room, Office room and Rs-3,30,809.00 Rs. 6.616.00 Do Do 30 (thirty) other facilities in existing building of Krishnagar days Govt. College, Nadia under Nadia Construction Division P.W.D. during the year 2020-2021.

S/d – A. Mitra Assistant Engineer(P.W.D) Krishnagar Construction Sub. Division-III GOVERNMENT OF WEST BENGAL PUBLIC WORKS DEPARTMENT Office of the Assistant Engineer (P.W.D) Krishnagar Construction Sub-Division No-III Arabindo Sarani, P.O.—Krishnagar, Dist.—Nadia. NIT NO-06/KC-III OF 2020-2021 Sl.no. 1 Price schedule for the work of "Toe protection work at approach of existing concrete road from Gouranga Setu towards Sanskrito Sahitya Charcha O Gabeshana Kendra from 0.100 KM to 0.175 km with 10 cm dia Eucalyptus bullah piling along with Drum Sheet Walling under Nadia Construction Division during the year 2020-2021".

Sl. Rate Amount Description of Items Quantity Unit No. (Rs.) (Rs)

1 Drum Sheet Walling 1.40m (av.) high on Sal-bullah / Eucalyptus bullah piling 10 cm dia. and 3.25m long driven 1.75m (av.) below G.L. and 75cm centre to centre including fitting fixing 3 nos. of half bullah pieces (from 10 cm dia) and drum(empty bitumen) sheet (approved condition) of height 1.5m , cutting and straightening drum sheet (each joint must have lap length of min.50mm) including cost of necessary nails, bolts, nuts etc. and providing 2 to 3m long half bullah ties of 10cm dia. @ 150.00 m 1244.00 186600.00 2.25 m centre to centre fixed with 10 cm dia. bullah posts driven 1.5m below G.L. including cost of all materials and one coat of coal tarring to all bullah etc. complete as per direction. (i) Using Eucalyptus bullah

2 Earthwork in excavation from borrow pits (land owned/arranged by the Department) and depositing in layers of 250 mm. including breaking clods in embankment works and to fill up back of abutments, depressions and ruts with an initial lead up to 50 m and initial lift up to 1.5 m making bunds at top as directed dressing 210.37 m3 317.97 66891.00 complete. (Borrow pit measurement) (i) In ordinary soil With Carried Earth carrige upto 5 km 3 Supplying empty Cement Bags & filling with dry uncompacted soil including placing the same after stitching, besides the bamboo walling 6113.00 Nos 16.34 99886.00 and/bullah pilling zones for better preventive measure to embankment protection. 353377.00 G.S.T. @ 12% 42405.00 395782.00 Labour welfare Cess @ 1% 3958.00 399740.00

(Rupees three lakh ninety nine thousand seven hundred & forty only) .

Sd/ Assistant Engineer (P.W.D.) Kgr. Constn. Sub-Divn.- No.- III Krishnagar, Nadia.

Page 1 of 1 GOVERNMENT OF WEST BENGAL PUBLIC WORKS DEPARTMENT Office of the Assistant Engineer (P.W.D) Krishnagar Construction Sub-Division No-III Arabindo Sarani, P.O.—Krishnagar, Dist.—Nadia. NIT NO-06/KC-III OF 2020-2021 Sl.no. 2 Price schedule for the work of Setting up of Vice-chancellor, Kanyashree University's Chamber, MIS Room, Office room and others facilities in existing building of Krishnagar Govt. college, Nadia under Nadia Construction Division, P.W.D. during the year 2020-2021. Sl. Rate Amount Description of Items Quantity Unit No. (Rs.) (Rs) 1 Post Constructional Measures : (a) Anti-termite treatment to the outside of foundations with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1%concentration) with water by weight including cutting shallow channel by excavating soil along and close to the wall face ensuring uniform dispersal of the chemical emulsion to a depth of 300mm. from the ground level by rodding with 12mm. dia. M.S. rod at 150mm.interval in the channel. 1.75 litres of chemical emulsion per metre length shall be used and a balance quantity of 0.5 litres of the chemical emulsion per running metre shall then be used to treat the back fill earth by directing the spray of the imulsion towards the wall surface. The entire work is to be carried out as per specification laid down in para 4.3.1.1 of code IS-6313 (Part-III) 1981.

80.00 m 72.00 5760.00

d) Anti-termite treatment to the junction of wood work and masonry walls with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight including spraying at the points of contact with the adjoining masonry by drilling 6m. dia holes at a downward angle of about 45 degree at the junction of woodwork and masonry and squirting chemical emulsion into these holes at the rate of half litre per hole. The entire work is to be carried out as per specification of Code I.S.- 6313 (Part-III)-1981. The shutters are to be sprayed with emulsion. on both sides. All wooden fixtures like almirahs, racks etc. are also to be throughly sprayed with chemical emulsion. (Payment will be made on the basis of outside measurements of doors and windows) 83.11 m2 61.00 5070.00

Page 1 of 12 Sl. Rate Amount Description of Items Quantity Unit No. (Rs.) (Rs) e)PostSpot Constructionalapplication for Measuresinsecticides : using Aqua base spray for pest (for bugs, cockroaches, silverfish, spider, termites, mosquitoes) to walls and ceiling etc. with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight including spraying the emulsified chemical @ 0.5 litres per sq.m. by a hand operated pressure pump on wall surfaces, ceiling, electrical fixture,electrical lines including drilling holes inplaces where source of termite is detected squirting chemical solution into the holes and sealing the holes with cement grout. (Rate is per sq.m. of the floor area while actual work will be all walls ceiling, rack, partition and furniture).

181.15 m2 49.00 8876.00

2 Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed.

46.95 m2 19.00 892.00

3 Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge 10.50 m3 166.00 1743.00

4 Cement concrete (1:1.5:3) with graded stone chips 5.6 mm size with hexagonal square mesh wire netting, I.R.C. fabric mesh or X.P. M. fitted and fixed after tying the existing reinforcement on concrete without distributing the same and with proper scarping and cleaning the reinforcement and disturbed concrete with wire brush etc. after applying a coat of cement including the cost of wire netting I.R.C or X. P. M. & cost of all handling and scaffolding complete as per direction of Engineer-in -charge. a) 20 mm thick

5.43 m2 483.00 2623.00

5 Cleaning the concrete surface by removing dirt and debris, marking defective locations and removing loose concrete by careful stripping untill hard surface is exposed, cutting the concrete to regular shape, wire brushing the exposed surface and removing debris from site complete as per direction of the Engineer - in - Charge.

5.43 m2 90.00 489.00

Page 2 of 12 Sl. Rate Amount Description of Items Quantity Unit No. (Rs.) (Rs) 6 CleaningPost Constructionalthe exposed Measuresreinforcement : preferably upto full diameter by wire brush, applying two coats of polymer based rust removing compound left for 24 hours, removing the coating and then applying two (2) coats of polymer modified anti corrosive protective coating formulated to inhibit the corrosion of reinforcement as per manufacturer's specification] [Mode of measurement:The affected surface area of reinforcement shall be considered for payment]

1.81 m2 785.00 1421.00

7 Washing and cleaning with oxalic acid powder using 33 gms./sq.m. (b) Floor/ dado other than marble 181.15 m2 553.00 1002.00

8 Preparation of drainage spout on roof for bituminous waterproofing treatment after required grading and shaping of the under bed with Cement Concrete (1:2:4) or Cement Mortar (1:4) as directed, Chamfering and moulding the parapet wall to form a bell mouth entry, if required and providing full course treatment with bituminous felt to facilitate quick and smooth drainage of watwr into the down pipes complete including cost of all materials and labour according to satisfaction of the Engineer - in - Charge. (This item shall be done for reparing works only and shall not be used when original/renewal of tarfelting work is proposed to be undertaken)

4 Nos 113.00 452.00

9 Application of priming coat for standard bituminous waterproofing treatment over flat roof with Bitumen primer of approved brand fufilling the provision of I.S. 1346 - 1991 & 3384 - 1986 applied @ 0.27 Liters /Sq.m. over clean and prepared roof surface complete as per satisfaction of the Engineer - in - Charge. All Floor - 181.15 m2 24.00 4348.00

10 Easing and oiling, cleaning collapsible gate and repairing to locking arrangements. 9.83 m2 17.00 167.00

11 Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). (e) Sal : Malayasian 0.04 m3 76096.00 3044.00

12 (i) Door stopper.(Brass) 10 Nos 117.00 1170.00 Page 3 of 12 Sl. Rate Amount Description of Items Quantity Unit No. (Rs.) (Rs) Post Constructional Measures : 13 ii) Godrej Hydraulic door closer fitted and fixed complete. (a) Heavy type 6 Nos 2064.00 12384.00

14 Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated (ix) 300mm long x 10mm dia. bolt. 2 Nos 99.00 198.00

15 Anodised aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted and fixed (iii) 300mm x 16mm dia. bolt. 2 Nos 231.00 462.00

16 Anodised aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 205/66) and fitted and fixed with cadmium plated v) 100 x 63 x 3.2mm. 2 Nos 72.00 144.00

17 Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed (a) With continuous plate base (Hexagonal/ Round rod) vi) 150 mm grip x 10 mm dia rod. 2 Nos 97.00 194.00

18 Labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damaes complete. (Concrete and brick work for mending damage will be paid separately) (a) Upto area 2.5 Sq.m 4.61 m2 119.00 549.00

19 Easing door and windows. 30 Nos 17.00 510.00

20 Styles and rails of wooden shutters fitted and fixed complete. (Payment to be made on area of new work only). In Ground Floor: (iv) 40mm. Thick shutter. (b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. 0.36 m2 2357.00 849.00

Page 4 of 12 Sl. Rate Amount Description of Items Quantity Unit No. (Rs.) (Rs) 21 PanelPost Constructional(made of single Measuresplank) of : door and window shutters to design as directed: In Ground Floor (Payment to be made on area of exposed new work). (In case of non-supply of single plank penal rate of reduction to a maximum of 30% will be made). (ii) 19mm thick panel of 30cm to 45cm width (b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak.

0.77 m2 1118.00 861.00

22 Providing and fixing of false ceiling with powder coated exposed G.I. grid suspension system (E-Grid U-1520 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200mm c/c ) consisting of Main Runner 3600 mm long, Cross Tee 1200 mm / 600 mm long and Wall Angle. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300mm c/c. The Main Runners to be placed @ 1200 mm. The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm X 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm X 600 mm. Grid of module size 600 mm X 600 mm shall be supported by 6 mm dia G.I. wire from purlins / soffit. 15mm thick OW Acoustic Board (Mineral Fiber Acoustic Ceiling Tiles) of approved patern and size 595mm X 595mm with NRC value > 0.65 should be placed in the Grid module to form a False Ceiling. All complete as per the drawing & directions of Engineer-in- charge. In ground floor. a) Acoustic False Ceiling (with 15mm thick OW Acoustic Board and E-Grid U- 1520).

18.00 m2 1357.00 24426.00

23 Supplying, fitting and fixing boiling water proof ply conforming to IS: 710-1977 bonded with phenol formaldehyde synthetic resin conforming to IS: 848-1974 of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge. [excluding the cost of supporting frame work and teak wood batten/Lipping] In Ground Floor (i) 4mm 2.24 m2 923.00 2068.00

Page 5 of 12 Sl. Rate Amount Description of Items Quantity Unit No. (Rs.) (Rs) 24 PlasterPost Constructional(to wall, floor, Measuresceiling :etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course,scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] i) With 1:6 cement mortar (b) 20 mm thick plaster 36.08 m2 161.57 5829.00

(ii) With 1:4 cement mortar (c) 10 mm thick plaster 10.87 m2 125.71 1366.00

25 Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface. Two Coats 782.46 m2 70.00 54772.00

26 Removing old scales, blisters etc. of interior surface of walls,ceiling by scraping etc. and preparing smooth and even surface with rendering or cement mortar (1:2) (as necessary), to make the surface suitable for receiving distemper. (Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge). 782.46 m2 1013.00 7926.00

27 (b) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. 3.00 m2 29.00 87.00

(b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. 19.40 m2 38.00 737.00

28 (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (a) On timber or plastered surface : With super gloss (hi-gloss) - (iv) Two coats (with any shade except white) 210.13 m2 81.00 17021.00

b) On steel or other metal surface : With super gloss (hi-gloss) - (iv) Two coats (with any shade except white) 68.47 m2 79.00 5409.00

Page 6 of 12 Sl. Rate Amount Description of Items Quantity Unit No. (Rs.) (Rs) 29 FrenchPost Constructionalpolishing to Measureswood work : including preparing surface (ordinary gloss) (b) On old French polished surface including complete removal of the old polish. 33.39 m2 538.00 17964.00

30 Removing loose scales, blisters etc. from old painted surface and thoroughly smoothening the surface to make the same suitable for receiving fresh coat of paint. 278.59 m2 21.00 5850.00

31 (b) Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand (1.5mm thick) 46.95 m2 110.00 5165.00

32 Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6 m height for external wall) (i) 3 mm thick (weighing 7.4 kg/Sq.m) 1.80 m2 477.00 859.00

33 Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete. A) UPVC Pipes: (ii) 110 mm. Dia. 20.00 m 251.00 5020.00

B) UPVC Fittings: a) Plain Tee (ii) 110 mm. Dia. 4.00 Nos 172.00 688.00

B) UPVC Fittings: c) Bend 87.5 degree (ii) 110 mm. Dia. 4.00 Nos 160.00 640.00

34 Clearing compound premises of shurbs, plants, jungles etc. by cutting and removing as directed (Specific permission of Engineer-in-Charge prior to execution will be necessary). (Payment to be made on area cleared) 900.00 m2 11.00 9900.00

35 Uprooting and removing plants from the surface of walls parapet etc and making good damages. (Repairing of damages to be paid separately). (a) Small plant of girth of exposed stem upto 75 mm. lift upto 6 mtr. Page 7 of 12 Sl. Rate Amount Description of Items Quantity Unit No. (Rs.) (Rs) Post Constructional Measures : 30 Nos 50.00 1500.00

(b) Medium size plant of girth of exposed stem above 75 mm. but not exceeding 150 mm. lift upto 6 mtr. 25 Nos 60.00 1500.00

36 Mazdoor (Male) 6 Nos 269.50 1617.00

37 Supplying, fitting and fixing shower of approved brand and make. (a) (i) Chromium plated round shower with revolving joint 100 mm dia with rubid cleaning system (Equivalent to Code No. 542(N) & Model - Tropical / Sumthing Special of ESSCO or similar brand). 2 Nos 452.00 904.00

38 Supplying, fitting and fixing Peet's valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I. marking with fittings (tested to 21 kg per sq. cm.). (vii) 25 mm dia 3 Nos 912.00 2736.00

(ix) 15 mm dia 3 Nos 521.00 1563.00

39 (a) (i) Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand). 5 Nos 539.00 2695.00

(b) (i) Chromium plated Stop Cock (Equivalent to Code No. 513(A) & 513(B) & Model - Tropical / Sumthing Special of ESSCO or similar 5 Nos 493.00 2465.00

(d) (i) Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand). 7 Nos 815.00 5705.00

Page 8 of 12 Sl. Rate Amount Description of Items Quantity Unit No. (Rs.) (Rs) 40 Supplying,Post Constructional fitting and Measures fixing CPVC : (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. (a) For Exposed Work (i) CPVC Pipes Class-1, SDR-11 (Dia) 15 mm

15.00 m 106.00 1590.00

25 mm 30.00 m 208.00 6240.00

41 Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. 2 Nos 1015.00 2030.00

42 Cleaning and disinfecting upto 2000 litre Water Tank including masonry reservoir. 1 Nos 155.00 155.00

43 Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint. (ii) 550 mm X 400 mm size

5 Nos 2208.00 11040.00

44 Supplying, fitting and fixing pedestal of approved make for wash basin (white) 5 Nos 1497.00 7485.00

45 Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. (v) 900 mm long 5 Nos 147.00 735.00

Page 9 of 12 Sl. Rate Amount Description of Items Quantity Unit No. (Rs.) (Rs) 46 Supplying,fittingPost Constructional and Measures fixing approved : brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps. (iv) 1050 mm long 3 Nos 91.00 273.00

47 Supplying, fitting & fixing Aluminium domical grating. (iii) 100 mm 6 Nos 49.00 294.00

48 Supply of UPVC pipes (B Type) & fittings conforming to IS- 13592-1992 (A) (i) Single Socketed 3 Meter Length (b) 110 mm 9.00 m 292.00 2628.00

(ii) Plain Tee (b) 110 mm 3 Nos 85.00 255.00

(iii) Door Tee (b) 110 mm 3 Nos 195.00 585.00

x) Bend 87.5º (b) 110 mm 3 Nos 120.00 360.00

xi) Door Bend (T.S.) (b) 110 mm 3 Nos 147.00 441.00

xv) Vent Cowl (b) 110 mm 2 Nos 33.00 66.00

49 Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any loor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Engineer-in-charge. (Payment will be made on centre line measurement of the total pipeline including specials. (B) Under ground (ii) 110 mm dia. 9.00 m 84.00 756.00

50 Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. (a) With 'P' trap Page 10 of 12 Sl. Rate Amount Description of Items Quantity Unit No. (Rs.) (Rs) Post Constructional Measures : 2 Nos 1421.00 2842.00

51 Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. (ii) 470 mm X 280 mm X 340 mm 2 Nos 945.00 1890.00

52 Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete. (a) E.W.C. (ii) Plastic (hallow type) white 2 Nos 380.00 760.00

53 Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete. i) Polythene Flush Pipe 2 Nos 155.00 310.00

54 Supplying, fitting and fixing bevelled edged mirror 5.5 mm thick silver red as per I.S. 3438 / 1965 together with brass C.P. hinges. (ii) 600 mm X 450 mm 5 Nos 484.00 2420.00

55 Supplying, fitting and fixing soap holder. (a) PTMT (Prayag or equivalent) 4 Nos 135.00 540.00

56 Supplying, fitting and fixing PTMT Smart Shelf of approved make of size 300 mm. 5 Nos 223.00 1115.00

57 Supplying, fitting and fixing towel rail with two brackets. (a) C.P. over brass (ii) 25 mm dia. and 600 mm long 5 Nos 430.00 2150.00

58 Dismantling & Refixing pit cover 4 Nos 35.00 140.00

59 Cleaning silt of inspection pit. 3 Nos 154.00 462.00

60 Removing sludge from septic tank, soak well etc. by methor labour including disposal of the same outside the compound as directed. (c) Upto 50 users:- (i) Within a lead of 150 metre 2 Nos 2304.00 4608.00

Page 11 of 12 Sl. Rate Amount Description of Items Quantity Unit No. (Rs.) (Rs) 61 MethorPost Constructional Mazdoor Measures : 2 Nos 325.60 651.00 292441.00 G.S.T. @ 12% 35093.00 327534.00 Labour welfare Cess @ 1% 3275.00 330809.00 (Rupees three lakh thirty thousand eight hundred & nine only) .

S/d Assistant Engineer (P.W.D.) Kgr. Constn. Sub-Divn.- No.- III Krishnagar, Nadia.

Page 12 of 12