Universal Featherweight Bipod Installation Instructions PART# BIP0300

Thank you for purchasing an ATI product!

Universal Bipod Assembly Point the rifle in a safe direction and place the safety in the "on" position. Next remove the magazine, pull back the bolt, and carefully inspect the chamber to be sure the rifle is unloaded. Step #1 Step #3 Decide to build a fixed bi-pod or swivel bi-pod. Install the fixed bi pod collar or swivel collar halves into the top side of the mounting bracket with the pins aligning with the holes in the mounting bracket. Non-Swivel Mount Swivel Mount Non-Swivel Swivel

Figure 1 Figure 3 Step #2 Step #4 After deciding to build a fixed or swivel bipod, install If the swivel collar halves were used, place the o-ring either the fixed bi-pod collar or the swivel collar halves into the groove on the top side of the mounting bracket. in the assembly. If the fixed bi-pod collar was used you will not need the o-ring.

Non-Swivel Swivel

Figure 2 Figure 4

www. ATIgunstocks.com Page 1 Universal Featherweight Bipod Installation Instructions PART# BIP0300

Thank you for purchasing an ATI product!

Step #5 Step #7 Install the yoke assembly over the post on the mounting Install the left and right legs by inserting the post on bracket and align (2) pins on the bottom of the yoke with the leg into the hole on the yoke. the holes in the fixed bi-pod collar or in open area between the swivel collar halves.

Non-Swivel Swivel Yoke

Figure 5

Step #6 Install the washer over the post and secure with the pink pre-coated #10 x 3/4" sheet metal screw using a Phillips Head Screwdriver. NOTE: Fixed Bi-pod will use the washer with the counterbore top and Swivel Bipod will use the washer with the flat top. Step #8 Figure 7 Secure the left and right legs to the yoke with the leg mounting washers and the #10 x 3/4" sheet metal screws using a Phillips Head Screwdriver

Counterbore Top Flat Top

Figure 6 Figure 8

www. ATIgunstocks.com Page 2 Universal Featherweight Bipod Installation Instructions PART# BIP0300

Thank you for purchasing an ATI product!

To install the Bipod to an AR-15 with Polymer Handguards go to page 5. Universal Bipod Assembly Point the rifle in a safe direction and place the safety in the "on" position. Next remove the magazine, pull back the bolt, and carefully inspect the chamber to be sure the rifle is unloaded. Step #1 Step #3 Inspect existing sling swivel stud for tightness. Place the 1/2 x 20 x 1-1/8 mounting column over the front sling swivel stud. Align the swivel stud through hole with the mounting column hole; then install and center the retaining pin.

Figure 1 Figure 3

Step #2 Step #4 Install the #10-32 x 1/4" Set Screw into the bottom of the Tighten the Set Screw which you installed in step #2. mounting column with the supplied Allen wrench. Install Install the new 10-32 x 7/16" threaded sling swivel stud the set screw until it is flush with the bottom of the 1/2 x and tighten. 20 x 1-1/8 mounting column.

Figure 4 Figure 2

www. ATIgunstocks.com Page 3 Universal Featherweight Bipod Installation Instructions PART# BIP0300

Thank you for purchasing an ATI product!

Step #5 Step #7 Remove the backing from the Neoprene Pad. Align and Place the mounting column washer over the affix to the bipod mounting bracket. mounting column. Install the 1/2 x 20 thin nut onto the column and hand tighten, plus 1/4 turn maximum. Failure to follow this procedure could result in damage to the stock. DO NOT

Figure 5

Step #6 Align and install Bipod over the mounting column with the legs parallel to the barrel and pointing toward the Figure 7 muzzle. (Depress the "Snap-N-Lock" button and rotate the legs 180 degrees.) Congratulations You have completed installation of your ATI Bipod

Snap and Lock Button

Figure 6

www. ATIgunstocks.com Page 4 Universal Featherweight Bipod Installation Instructions PART# BIP0300

Thank you for purchasing an ATI product!

AR-15 Bipod Assembly Point the rifle in a safe direction and place the safety in the "on" position. Next remove the magazine, pull back the bolt, and carefully inspect the chamber to be sure the rifle is unloaded.

Step #1 Step #3 Remove the lower hand guard. Install the #10-32 x 1/4" Set Screw into the top of the mounting column with the supplied Allen wrench. Install the set screw until it is flush with the bottom of the mounting column.

Figure 3 Figure 1

Step #4 Place the mounting column over the front sling swivel Step #2 stud. Align the swivel stud through the hole with the Insert the 10-32 x 3/4" round Bi-Pod barrel nut threaded mounting column hole; then install and center the adapter through the hole in the lower hand guard, align retaining pin. Tighten the Allen Screw which you and install the 10-32 x 5/16" sling swivel stud. Next, installed in step #2. Install the new 10-32 x 7/16" reinstall the lower hand guard. threaded sling swivel stud and tighten.

Figure 2

Figure 4

www. ATIgunstocks.com Page 5 Universal Featherweight Bipod Installation Instructions PART# BIP0300

Thank you for purchasing an ATI product!

Step #5 Step #7 Remove the backing from the Neoprene Pad. Align and Place the nylon washer over the mounting column. affix to the bipod mounting bracket. Install the 1/2" x 20 thin nut onto the column and hand tighten, plus 1/4 turn maximum. Failure to follow this procedure could result in damage to stock. DO NOT OVER-TIGHTEN!

Figure 5 Step #6 Align and install the Bipod over the mounting column with the legs parallel to the barrel and pointing toward the muzzle. (Depress the "Snap-N-Lock" button and Figure 7 rotate the legs 180 degrees.)

Congratulations You have completed installation of your ATI Bipod

Snap and Lock Button

Figure 6