Pillar of the Industry

PILL AR OF THE MORTARS AND GROUTS FOR INDUSTRY Burlington Office Boisbriand Office Brantford Office Sudbury Office MASONRY RESTORATION 3385, Harvester Rd. 3825, rue Alfred-Laliberté 541, Oak Park Rd. 644, Simmons Rd. Burlington, ON Boisbriand, QC Brantford, ON Dowling, ON L7N 3N2 J7H 1P7 N3T 5L8 P0M 1R0 Phone: (905) 639-2993 Phone: (450) 430-4104 Phone: (519) 756-6177 Phone: (705) 855-1155 Fax: (905) 333-3730 Fax: (450) 430-6855 Fax: (519) 756-7490 Fax: (705) 855-1122 04 www.king-masonry.com

KING_HBS binder_ANG_21-08-14— CGG_1” Référence des couleurs: PMS 296C PMS 485C CONTENT TABLE

INTRODUCTION • Presentation

BEDDING MORTARS • HLM-500 (Hydraulic Lime) • RosenMix 500 (Natural Cement) • PHL-500 (Pozzolanic lime) • MasonMix (Complete series)

REPOINTING MORTARS • HLM-350 (Hydraulic Lime) • RosenMix 350 (Natural Cement) • PHL-350 (Pozzolanic lime) • MasonCare 300 • MasonCare 1258 • Reconstec 900

GROUTS • KING HL-5 (Hydraulic Lime) • KING LS • KING RPL-6 • Reconstec 700 (Injection grout – complete series)

STONE REPAIR • Granite, Sandstone , Limestone, Terra Cotta, Marble and Travertine

ARCHITECTURAL • Reconstec 300 AC STONE REPAIR • Reconstec 350 AC • Anchoring Cement

OTHER PRODUCTS • Reconstec MF (Polyurethane)

www.king-masonry.com IntroductIon on I Introduct ne I l e dI = c nt ed ed I r r

bne bne

P not

I ub

do r introduction

Active on construction sites since 1963, King Packaged Materials Company is proud to present its division devoted entirely to the conservation and restoration of heritage buildings.

Working within a well-established budget, our mission is to participate in the preservation of built heritage by offering the best products, skills and techniques in the field of masonry restoration.

At KING, we manufacture and distribute a range of products made from a variety of sands mixed with binders which have historical characteristics, such as hydrated lime, hydraulic lime or natural cement. Our highly qualified team is composed of honest and competent individuals who can guide you through your project, every step of the way.

The Château Frontenac in Quebec City, the Canadian Parliament in Ottawa and the Saskatchewan Parliament in Regina are just a few examples of projects in which the KING team’s expertise was enlisted.

Want to learn more about the products and skills required in masonry restoration? Do you need help with a project or want to get training at our training centre located in Boisbriand, Quebec? Contact us today!

Thank you for your trust in the KING team.

Note: The content of this binder is updated continuously. In order to ensure that you are referencing our most recent information, please visit our website at www.kpmindustries.com.

Mixing Strength With Satisfaction beddInG MortArS S r A G Mort n beddI HYDRAULIC LIME MORTAR - DIVISION 04

HLM-500

HLM-500 is a pre-blended, pre-packaged mortar specifically designed for use OPTIMUM PERFORMANCE with clay, concrete and stone masonry units within the context of an historic • The substrate and mortar temperature should be between 5°C and 38°C preservation project or of a new sustainable construction project (LEED). HLM- (40°F and 100°F) and maintained in this range for 10 days after mortar 500 mortar is a blend of natural hydraulic lime (St-Astier), hydrated type S lime application. NOTE: If the temperature will be under 0°C in 90 days and masonry sand. It is available in off white, but can also be blended with a following the end of the cure, protect the mortar against snow and water variety of coloring agents. for the entire period where the temperature will be under 0°C or use the RosenMix 500. FEATURES & BENEFITS • Never add water to regain lost workability. Just mix again. • Does not contain cement. • Never use on-site admixtures to modify setting time, workability, • Excellent resistance to freeze-thaw cycles. or any other properties of plastic or hardened mortar. • Excellent resistance to de-icing salts. • Excellent vapour transmission and auto-healing properties. YIELD • Very low shrinkage. 30 kg (66 lb.) bag contains approximately 0.018 m3 (0.65 ft3) of fresh • Pre-blended, ensuring consistency from the first batch to the last. mortar. • All KING products are manufactured using ISO 9001:2008 Certified Processes. PACKAGING HLM-500 mortar is normally packaged in 30 kg (66 lb.) triple lined bags and USES poly wrapped on wooden pallets. All KING products can be custom packaged • Ideal for use in laying clay, concrete and stone masonry units in to suit specific job requirements. repair of historic buildings or monuments. • Ideal for use in laying clay, concrete and stone masonry units in STORAGE AND SHELF LIFE the context of a new sustainable construction (LEED). Material should be stored in a dry covered area protected from the elements. • Can be applied indoors and outdoors. Unopened bags have a shelf life of 12 months. • Can be used as a repointing mortar. SAFETY PROCEDURES PROCEDURES HLM-500 mortar contains natural hydraulic lime (St-Astier) and hydrated Mixing: lime. Normal safety-wear such as rubber gloves, dust mask and safety glass- HLM-500 mortar should be mixed with 5.5 litres (1.45 US gallon) of potable es used to handle conventional cement based products should be worn. water per 30 kg (66 lb.) bag, in a clean paddle mixer. Add 5.0 litres (1.3 US Material Safety Data Sheets are available upon request. gallon) of water into the mixer along with 30 kg (66 lb.) of HLM-500 mortar and mix for 3-5 minutes. If a coloring agent is required, add to mixer and Note: The contents of this data sheet are updated regularly. To ensure that you have the most continue mixing for an additional 5 to 10 minutes. Use the remaining water recent version, please visit our website at the following address: www.king-masonry.com to adjust the mix in order to obtain the desired consistency. This product is designed to meet the performance specifications outlined in this product data TECHNICAL DATA sheet. If the product is used in conditions for which it was not intended, or applied in a manner The following data is representative of typical values achievable under lab- contrary to the written recommendations contained in the product data sheet, the product may oratory conditions according to CSA A-179-04. Results in the field may vary. not reach such performance specifications. The foregoing is in lieu of any other warranties, representations or conditions, expressed or implied, including, but not limited to, implied COMPRESSIVE STRENGTH warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. CSA A23.2-8A 7 Day 1.0 MPa (145 psi) V0115 28 Day 2.2 MPa (320 psi) 90 Day 3.5 MPa (510 psi) 365 Day 4.5 MPa (650 psi)

AIR CONTENT ASTM C 231 8-15%

FLOW ASTM C 1437 100 - 115 %

CURING Curing is essential to optimize physical properties of the mortar. After material has reached initial set, continuously moist cure for a period of 7 days.

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction HYDRAULIC LIME MORTAR - DIVISION 04

HLM-500

KING PACKAGED MATERIALS COMPANY

Burlington Office Boisbriand Office Brantford Office Sudbury Office 3385 Harvester Rd. 3825 rue Alfred-Laliberté 541 Oak Park Rd. 644 Simmons Rd. Burlington, ON Boisbriand, QC Brantford, ON Dowling, ON L7N 3N2 J7H 1P7 N3T 5L8 P0M 1R0 Phone: (905) 639-2993 Phone: (450) 430-4104 Phone: (519) 756-6177 Phone: (705) 855-1155 Fax: (905) 333-3730 Fax: (450) 430-6855 Fax: (519) 756-7490 Fax: (705) 855-1122 Natural Cement MORTAR - DIVISION 04

RosenMix 500

KING RosenMix 500 is a pre-blended, pre-packaged mortar made from Initial setting time: 2:00 100% natural binders, specifically designed for use in applications of new Final setting time: 2:30 construction or restoration. This product is a blend of natural cement, Type S hydrated lime, masonry sand and other carefully selected components. RosenMix 500 is ocher in color, but can also be blended with a variety of OPTIMUM PERFORMANCE coloring agents. • The substrate and mortar temperature should be between 5 and 38°C (40 and 100°F) and maintained in this range for 72 hours after mortar FEATURES & BENEFITS application. • Rapid setting time. • Never use on-site admixtures to modify setting time, workability, or any • Excellent workability. other properties of plastic or hardened mortar. • Excellent durability. • Use only the recommended water content to achieve the desired plastic • Low modulus of elasticity. and hardened mortar properties. • Pre-blended, ensuring consistency from the first batch to the last. • All King products are manufactured using ISO 9001:2008 Certified YIELD Processes. 30 kg (66 lb.) bag contains approximately 0.018m3 (0.65ft3) of fresh mortar.

USES PACKAGING • Ideal for masonry applications where a rapid setting time is important. RosenMix 500 is normally packaged in 30 kg (66 lb.) triple lined bags and Ideal for use where the protection times are short. poly wrapped on wooden pallets. All KING products can be custom packaged • Can be used for laying bricks or for repointing. to suit specific job requirements. • Can be applied indoors, outdoors or for any other masonry application. STORAGE AND SHELF LIFE PROCEDURES Material should be stored in a dry covered area protected from the elements. Mixing: Unopened bags have a shelf life of 12 months. For best results, add a maximum of 6.2 litres (1.58 US gallon) of potable water per 30 kg (66 lb.)of RosenMix 500 in a clean mortar mixer. Pour SAFETY PROCEDURES 5.5 litres (1.32 US gallon) in the mixer, then add 30 kg (66 lb.) of RosenMix 500 contains natural cement and lime. Normal safety-wear such RosenMix 500 and mix for 3 to 5 minutes. If a coloring agent is required, as rubber gloves, dust mask and safety glasses used to handle conventional add to mixer and continue mixing for an additional 5 to 10 minutes. Add only cement based products should be worn. Material Safety Data Sheets are enough of remaining water to bring mix to desired consistency. available upon request.

Caution: Note: The contents of this data sheet are updated regularly. To ensure that you have the most Use mortar within 45 minutes following mixing. After 10 minutes without recent version, please visit our website at the following address: www.king-masonry.com mixing, if the mortar has lost its workability, simply mix again without adding water. After 45 minutes, any unused mortar must be discarded. Do not add This product is designed to meet the performance specifications outlined in this product data water to the mortar after the initial set has begun. sheet. If the product is used in conditions for which it was not intended, or applied in a manner contrary to the written recommendations contained in the product data sheet, the product may Curing: not reach such performance specifications. The foregoing is in lieu of any other warranties, Curing is essential to optimize physical properties of the mortar. After material representations or conditions, expressed or implied, including, but not limited to, implied has reached initial set, continuously moist cure for a period of 3 days. warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. TECHNICAL DATA V1014 The following data is representative of typical values achievable under laboratory conditions. Results in the field may vary.

Minimal compressive strength 7 day 2 MPa (290 psi) 28 day 5 MPa (725 psi) 90 day 10 MPa (1450 psi)

Flow 105 +- 5%

Air Content 8% to 15%

King packaged materials company Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction Natural Cement MORTAR - DIVISION 04

RosenMix 500

King packaged materials company

PHL-500

KING PHL-500 mortar is a pre-blended and pre-bagged mortar specially OPTIMUM PERFORMANCE designed to be used when laying bricks, blocks, stones and other masonry units • Do not use PHL-500 as a repointing mortar when lower compressive within the context of an historic preservation project or of a new sustainable strengths are required. In this case, use PHL-350. construction project (LEED). PHL-500 mortar is a blend of Pozzolanic lime, • The substrate and mortar temperature should be maintained between hydrated type S lime, an air entraining agent, and masonry sand. It is off white 5 °C and 38 °C (40 °F and 100 °F) for 72 hours after mortar application. in color, but can also be blended with a variety of coloring agents. • Never add water to regain lost workability. In this case, just mix again. • Never use on-site admixtures to modify setting time, workability or any FEATURES & BENEFITS other properties of plastic or hardened mortar. • Does not contain cement. • Better salt-scaling resistance than hydrated lime. YIELD • Excellent vapour transmission and auto-healing properties. 30 KG (66 lb) bag contains approximately 0.018 m3 (0.65 ft3) of fresh mortar. • Very low shrinkage. • Pre-blended, ensuring consistency from the first batch to the last. PACKAGING • All KING products are manufactured using ISO 9001:2008 PHL-500 is normally packaged in 30 KG (66 lb) triple-lined bags and Certified Processes. polywrapped on wooden pallets. All KING products can be custom packaged to suit specific job requirements. USES • Ideal for use in laying clay, concrete and stone masonry units in repair of STORAGE AND SHELF LIFE historic buildings or monuments. Material should be stored in a dry, covered area, protected from the elements. • Ideal for use in laying clay, concrete and stone masonry units in the Unopened bags have a shelf life of 12 months. context of new sustainable construction (LEED). • Can be applied indoors and outdoors. SAFETY PROCEDURES • Can be used as a repointing mortar when higher compressive strengths Normal safety-wear such as rubber gloves, dust mask and safety glasses are required. used to handle conventional cement based products should be worn. Safety Data Sheets are available upon request. PROCEDURES Mixing: Note: The contents of this data sheet are updated regularly. To ensure that you have the most PHL-500 mortar should be mixed with 5.5 litres (1.45 US gallons) of potable recent version, please visit our website at the following address: www.king-masonry.com water per 30 kg (66 lb.) bag, in a clean paddle mixer. Add 5.0 litres (1.3 US gallons) of water into the mixer along with 30 kg (66 lb.) of PHL-500 mortar This product is designed to meet the performance specifications outlined in this product data and mix for 3-5 minutes. If a coloring agent has been added continue mixing sheet. If the product is used in conditions for which it was not intended, or applied in a manner for an additional 5 to 10 minutes. Use the remaining water to adjust the mix contrary to the written recommendations contained in the product data sheet, the product may in order to obtain the desired consistency. not reach such performance specifications. The foregoing is in lieu of any other warranties, representations or conditions, expressed or implied, including, but not limited to, implied Curing: warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. Curing is essential to optimize physical properties of the mortar. After material has reached initial set, continuously moist cure for a period of 3 to 7 days. V0318

TECHNICAL DATA*

FLOW ASTM C 1437 100 - 115%

COMPRESSIVE STRENGTH CSA A23.2-8A 7 Day 1.7 MPa 28 Day 3.2 MPa 90 Day 5.2 MPa

AIR CONTENT 18% Maximum

WATER RETENTION 75% Minimum

VAPOUR TRANSMISSION 28 Perms

*These figures have been obtained in a lab

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction BEDDING MORTAR - DIVISION 04

PHL-500

KING PACKAGED MATERIALS COMPANY

MASONMIX

MasonMix is a pre-blended, pre-packaged Type O Mortar specifically OPTIMUM PERFORMANCE designed for use in applications of non-load bearing wall applications. This • Do not use the MasonMix when type N mortar or type S mortar is mortar is a blend of cementitious materials, Type S hydrated lime, masonry specified. In this case, it is recommended to use KING 1-1-6 or sand and other carefully selected components. MasonMix conforms to CSA A KING 2-1-9, respectively. 179-04 (Annex A, Table A3) for type O mortar with the addition of water. It • The substrate and mortar temperature should be between 5°C and 38°C is available in grey, cream and white, but can also be blended with a variety (40°F and 100°F) and maintained in this range for 72 hours after mortar of coloring agents. application. • Never use on-site admixtures to modify setting time, workability, or any FEATURES & BENEFITS other properties of plastic or hardened mortar. • High vapor transmission properties. • Use only the recommended water content to achieve the desired plastic • Superior workability. and hardened mortar properties. • Autogeneous healing properties. • Low strength. YIELD • Pre-blended, ensuring consistency from the first batch to the last. 30 kg (66 lb.) bag contains approximately 0.018 m3 (0.65 ft3) of fresh • All KING products are manufactured using ISO 9001:2008 Certified mortar. Processes. PACKAGING USES MasonMix is normally packaged in 30 kg (66 lb.) triple lined bags and poly • Ideal for use in non load bearing wall applications. wrapped on wooden pallets. All KING products can be custom packaged to • Can be applied indoors, outdoors or for any other masonry application suit specific job requirements. where low strength and superior workability is required. STORAGE AND SHELF LIFE PROCEDURES Material should be stored in a dry covered area protected from the elements. Mixing: Unopened bags have a shelf life of 12 months. For best results, add a maximum of 5 litres (1.3 US gallon) of potable water per 30 kg (66 lb.) bag into a clean mortar mixer. Pour 4.5 litres SAFETY PROCEDURES (1.2 US gallon) of water in the mixer, then add the MasonMix and mix for MasonMix contains Portland cement and lime. Normal safety-wear such as 3 to 5 minutes. If a coloring agent is required, add to mixer and continue rubber gloves, dust mask and safety glasses used to handle conventional mixing for an additional 5 to 10 minutes. Add only enough of remaining cement based products should be worn. Material Safety Data Sheets are water to bring mix to desired consistency. available upon request.

TECHNICAL DATA Note: The contents of this data sheet are updated regularly. To ensure that you have the most The following data is representative of typical values achievable under recent version, please visit our website at the following address: www.king-masonry.com laboratory conditions according to CSA A 179-04 (Annex A, Table A3) for type O. Results in the field may vary. This product is designed to meet the performance specifications outlined in this product data sheet. If the product is used in conditions for which it was not intended, or applied in a manner COMPRESSIVE STRENGTH contrary to the written recommendations contained in the product data sheet, the product may (MINIMUM) not reach such performance specifications. The foregoing is in lieu of any other warranties, 7 Days 1.5 MPa (217 psi) representations or conditions, expressed or implied, including, but not limited to, implied 28 day 2.4 MPa (350 psi) warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. FLOW 100-115% V1014

AIR CONTENT 18 % Maximum

WATER RETENTION 75 % Minimum

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction TYPE O MORTAR - DIVISION 04

MASONMIX

KING PACKAGED MATERIALS COMPANY

MASONMIX 600

MasonMix 600 is a pre-blended, pre-packaged mortar, specifically designed OPTIMUM PERFORMANCE for use in applications of non load bearing wall. MasonMix 600 is a blend • Do not use the MasonMix 600 when mortar type N or S is specified. In this of 1 part of Portland cement, 2 parts of Type S hydrated lime, 6 parts of case, it is recommended to use the King 1-1-6 or King 2-1-9. masonry sand and other carefully selected components. MasonMix 600 • The substrate and mortar temperature should be between 5 and 38°C conforms to ASTM C270 for Type O mortar, by volume, with the addition of (40 and 100°F) and maintained in this range for 72 hours after mortar water. It is available in grey, cream and white, but can also be blended with application. a variety of coloring agents. • Never use on-site admixtures to modify setting time, workability, or any other properties of plastic or hardened mortar. FEATURES & BENEFITS • Use only the recommended water content to achieve the desired plastic • High vapor transmission properties. and hardened mortar properties. • Superior workability. • Autogeneous healing properties. YIELD • Low strength. 30 kg bag contains approximately 0.018m3 (0.65ft3) of fresh mortar. • Pre-blended, ensuring consistency from the first batch to the last. • All KING products are manufactured using ISO 9001:2008 Certified PACKAGING Processes. MasonMix 600 is normally packaged in 30 kg (66 lb.) triple lined bags and poly wrapped on wooden pallets. All KING products can be custom packaged USES to suit specific job requirements. • Ideal for use in non load bearing wall applications. • Can be applied indoors, outdoors or for any other masonry application STORAGE AND SHELF LIFE where low strength and superior workability is required. Material should be stored in a dry covered area protected from the elements. Unopened bags have a shelf life of 12 months. PROCEDURES Mixing: SAFETY PROCEDURES For best results, add a maximum of 5.0 liters (1.3 US gallon) of potable water MasonMix 600 contains Portland cement and lime. Normal safety-wear such per 30 kg (66 lb.) bag into a clean mortar mixer. Pour 4.0 liters (1.0 US as rubber gloves, dust mask and safety glasses used to handle conventional gallon) of water then add the MasonMix and mix for 3 to 5 minutes. If a cement based products should be worn. Material Safety Data Sheets are coloring agent is required, add to mixer and continue mixing for an additional available upon request. 5 to 10 minutes. Add only enough of remaining water to bring mix to desired consistency. Note: The contents of this data sheet are updated regularly. To ensure that you have the most recent version, please visit our website at the following address: www.king-masonry.com TECHNICAL DATA The following data is representative of typical values achievable under This product is designed to meet the performance specifications outlined in this product data laboratory conditions. Results in the field may vary. sheet. If the product is used in conditions for which it was not intended, or applied in a manner contrary to the written recommendations contained in the product data sheet, the product may COMPRESSIVE STRENGTH not reach such performance specifications. The foregoing is in lieu of any other warranties, 7 Day 3 MPa representations or conditions, expressed or implied, including, but not limited to, implied 28 Day 5 MPa warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. FLOW V1013 100 to 115%

AIR CONTENT 18% Maximum

WATER RETENTION 70% Minimum

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RELATED MORTARS - DIVISION 04

MASONMIX 600

KING PACKAGED MATERIALS COMPANY

MASONMIX 700

KING MasonMix 700 is a pre-blended, pre-packaged mortar. It is a blend REPOINTING MORTAR: of Portland cement, Type S hydrated lime, masonry sand and other carefully selected components. MasomMix 700 is grey, cream or white in color, but VICAT CONE can also be blended with a variety of coloring agents. ASTM C 780 15mm +/- 5mm

FEATURES & BENEFITS COMPRESSIVE STRENGTH • High vapor transmission properties. (MINIMUM) • Superior workability. 7 day 5.0 MPa (725 psi) • Autogeneous healing properties. 28 DAY 9.0 MPa (1305 psi) • Medium strength. • Pre-blended, ensuring consistency from the first batch to the last. AIR CONTENT 18% Maximum • All KING products are manufactured using ISO 9001:2008 Certified Processes. OPTIMUM PERFORMANCE USES • The substrate and mortar temperature should be between 5 and 38°C • Ideal for use in non load bearing wall applications. (40 and 100°F) and maintained in this range for 72 hours after mortar • Can be applied indoors, outdoors or for any other masonry application application. where low strength and superior workability is required. • Never use on-site admixtures to modify setting time, workability, or any • Can be used as a repointing mortar. other properties of plastic or hardened mortar. • Use only the recommended water content to achieve the desired plastic PROCEDURES and hardened mortar properties. Mixing: Bedding mortar For best results, add a maximum of 4.5 liters (1.2 US gallon) of potable YIELD water per 30 kg (66 lb.) into a clean mortar mixer. Pour 3.6 liters (1.0 US 30 kg (66 lb.) bag contains approximately 0.018 m3 (0.65 ft3) of fresh gallon) of water then add the MasonMix 700 and mix for 3 to 5 minutes. If a mortar. coloring agent is required, add to mixer and continue mixing for an additional 5 to 10 minutes. Add only enough of remaining water to bring mix to desired PACKAGING consistency. MasonMix 700 is normally packaged in 30 kg (66 lb.) triple lined bags and poly wrapped on wooden pallets. All KING products can be custom packaged Mixing: Repointing mortar to suit specific job requirements. For best results, add a maximum 3.8 litres (1.13 US gallon) of potable water per 30 kg (66 lb.) bag into a clean mortar mixer. Gradually add MasonMix STORAGE AND SHELF LIFE 700 to water and mix, operating until the mix is heavy bodied enough to Material should be stored in a dry covered area protected from the elements. retain it’s shape when fashioned by hand into a ball. Wait approximately 30 Unopened bags have a shelf life of 12 months. minutes before the application. SAFETY PROCEDURES TECHNICAL DATA MasonMix 700 contains Portland cement and lime. Normal safety-wear such The following data is representative of typical values achievable under as rubber gloves, dust mask and safety glasses used to handle conventional laboratory conditions .Results in the field may vary. cement based products should be worn. Material Safety Data Sheets are available upon request. BEDDING MORTAR: Note: The contents of this data sheet are updated regularly. To ensure that you have the most FLOW recent version, please visit our website at the following address: www.king-masonry.com ASTM C 109 105-115% This product is designed to meet the performance specifications outlined in this product data COMPRESSIVE STRENGTH sheet. If the product is used in conditions for which it was not intended, or applied in a manner (MINIMUM) contrary to the written recommendations contained in the product data sheet, the product may 7 day 4.0 MPa (580 psi) not reach such performance specifications. The foregoing is in lieu of any other warranties, 28 day 5.3 MPa (769 psi) representations or conditions, expressed or implied, including, but not limited to, implied warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. AIR CONTENT 18% Maximum V1013 WATER RETENTION 70% Minimum

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RELATED MORTARS - DIVISION 04

MASONMIX 700

KING PACKAGED MATERIALS COMPANY

HLM-350

HLM-350 is a pre-blended, pre-packaged mortar specifically designed for use PLACING in repointing historic buildings or for restoration of sustainable and LEED Clean the area to be repaired, removing all loose material equivalent to 2 projects. HLM-350 mortar is a blend of natural hydraulic lime (St-Astier) times the thickness of the joint. Moisten the area to be repaired with potable and masonry sand. It is available in off white, but can also be blended with water, leaving the masonry unit saturated but free of standing water. Place a variety of coloring agents. HLM-350 mortar into the joint in successive layers to a maximum depth of 6 mm (¼ inch). Compact well and let dry slightly before adding additional FEATURES & BENEFITS layers. Tool the joints prior to setting. Finish joints. • Does not contain cement. • Excellent resistance to freeze-thaw cycles. CURING • Excellent resistance to de-icing salts. Curing is essential to optimize physical properties of the mortar. After ma- • Excellent vapour transmission and auto-healing properties. terial has reached initial set, continuously moist cure for a period of 7 days. • Very low shrinkage. • Pre-blended, ensuring consistency from the first batch to the last. OPTIMUM PERFORMANCE • All KING products are manufactured using ISO 9001:2008 Certified • HLM-350 mortar should not be used for bedding of concrete Processes. masonry units. In this case, please refer to HLM-500 mortar or KING 1-1-6. USES • The substrate and mortar temperature should be between 5°C and • Ideal for use in repointing historic buildings or monuments. 38°C (40°F and 100°F) and maintained in this range for 10 days • Ideal for use in repointing more recent, sustainable construction (LEED). after mortar application. NOTE: If the temperature will be under 0°C in • Can be applied indoors and outdoors. 90 days following the end of the cure, protect the mortar against snow and water for the entire period where the temperature will be under 0°C PROCEDURES or use the RosenMix 350. Mixing: • Never add water to regain lost workability. Just mix again. HLM-350 mortar should be mixed with 4.5 litres (1.2 US gallon) of potable • Never use on-site admixtures to modify setting time, workability, water per 30 kg (66 lb.) bag, in a clean paddle mixer. Add 4.0 litres (1.05 or any other properties of plastic or hardened mortar. US gallon) of water into the mixer along with 30 kg (66 lb.) of HLM-350 mortar and mix for 3-5 minutes. If a coloring agent is required, add to mixer YIELD and continue mixing for an additional 5 to 10 minutes. Use the remaining 30 kg (66 lb.) bag contains approximately 0.018 m3 (0.65 ft3) of fresh mor- water to adjust the mix in order to obtain the desired consistency. tar, enough to repoint approximately 90 linear meters (300 ft).

TECHNICAL DATA PACKAGING The following data is representative of typical values achievable under lab- HLM-350 mortar is normally packaged in 30 kg (66 lb.) triple lined bags and oratory conditions according to CSA A-179-04. Results in the field may vary. poly wrapped on wooden pallets. All KING products can be custom packaged to suit specific job requirements. COMPRESSIVE STRENGTH CSA A23.2-8A STORAGE AND SHELF LIFE 7 Day 0.7 MPa (100 psi) Material should be stored in a dry covered area protected from the elements. 28 Day 1.8 MPa (260 psi) Unopened bags have a shelf life of 12 months. 90 Day 2.7 MPa (390 psi) 120 Day 3.0 MPa (435 psi) SAFETY PROCEDURES 365 Day 3.5 MPa (510 psi) HLM-350 mortar contains natural hydraulic lime (St-Astier). Normal safety-wear such as rubber gloves, dust mask and safety glasses used to handle AIR CONTENT conventional cement based products should be worn. Material Safety Data ASTM C 231 8-15% Sheets are available upon request.

FLOW Note: The contents of this data sheet are updated regularly. To ensure that you have the most ASTM C 1437 < 80 % recent version, please visit our website at the following address: www.king-masonry.com VICAT CONE This product is designed to meet the performance specifications outlined in this product data 15 mm ± 5 mm ASTM C 780 sheet. If the product is used in conditions for which it was not intended, or applied in a manner SHRINKAGE contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, ASTM C 596 0.05% representations or conditions, expressed or implied, including, but not limited to, implied warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. V0115

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction HYDRAULIC LIME MORTAR - DIVISION 04

HLM-350

KING PACKAGED MATERIALS COMPANY

ROSENMIX 350

KING RosenMix 350 is a pre-blended, pre-packaged mortar made from VICAT CONE 100% natural binders, specifically designed for use in applications of ASTM C 780 25mm (+- 5mm) repointing. This product is a blend of natural cement, Type S hydrated lime, masonry sand and other carefully selected components. RosenMix 350 is AIR CONTENT ocher in color, but can also be blended with a variety of coloring agents. ASTM C 231 8% to 15%

FEATURES & BENEFITS Initial setting time: 2:00 • Rapid setting time. Final setting time: 2:30 • Excellent workability. • High resistance to de-icing salts. • Excellent durability. OPTIMUM PERFORMANCE • Low modulus of elasticity. • The substrate and mortar temperature should be between 5 and 38°C • Pre-blended, ensuring consistency from the first batch to the last. (40 and 100°F) and maintained in this range for 72 hours after mortar • All KING products are manufactured using ISO 9001:2008 Certified application. Processes. • Never use on-site admixtures to modify setting time, workability, or any other properties of plastic or hardened mortar. USES • Use only the recommended water content to achieve the desired plastic • Ideal for masonry applications where a rapid setting time is important. and hardened mortar properties. • Ideal for use where the protection times are short. • Can be applied indoors, outdoors or for any other masonry application. YIELD 30 kg (66 lb.) bag contains approximately 0.018m3 (0.65ft3) of fresh mortar. PROCEDURES Mixing: PACKAGING For best results, add a maximum of 5.3 liters (1.32 US gallons) of potable RosenMix 350 is normally packaged in 30 kg (66 lb.) triple lined bags and water per 30 kg (66 lb.) of RosenMix 350 into a clean mortar mixer. Mix poly wrapped on wooden pallets. All KING products can be custom packaged the product, operating until the mix is heavy bodied enough to retain it’s to suit specific job requirements. shape when fashioned by hand into a ball. If only a small quantity of mortar is necessary, it is important to first mix the whole dry content of the bag in STORAGE AND SHELF LIFE a clean container. Afterwards, water can be added to obtain the required Material should be stored in a dry covered area protected from the elements. amount of mortar. Unopened bags have a shelf life of 12 months.

Caution: SAFETY PROCEDURES Use mortar within 45 minutes following mixing. After 10 minutes without RosenMix 350 contains natural cement and lime. Normal safety-wear such mixing, if the mortar has lost its workability, simply mix again without adding as rubber gloves, dust mask and safety glasses used to handle conventional water. After 45 minutes, any unused mortar must be discarded. Do not add cement based products should be worn. Material Safety Data Sheets are water to the mortar after the initial set has begun. available upon request.

Placing: Note: The contents of this data sheet are updated regularly. To ensure that you have the most Clean the area to be repaired, removing all loose material on a thickness recent version, please visit our website at the following address: www.king-masonry.com corresponding to 2 times the thickness of the joint. Moist the area to be repaired with potable water, leaving the concrete saturated but free of This product is designed to meet the performance specifications outlined in this product data standing water (SSD). Place RosenMix 350 into the joint in successive sheet. If the product is used in conditions for which it was not intended, or applied in a manner layers to a maximum depth of 6 mm (¼ inch). Compact well before adding contrary to the written recommendations contained in the product data sheet, the product may additional layers. Tool the joints prior to final set time. not reach such performance specifications. The foregoing is in lieu of any other warranties, representations or conditions, expressed or implied, including, but not limited to, implied TECHNICAL DATA warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. The following data is representative of typical values achievable under laboratory conditions. Results in the field may vary. V1014

MINIMUM COMPRESSIVE STRENGTH 7 day 1 MPa (145 psi) 28 day 3.5 MPa (508 psi) 90 day 7 MPa (1015 psi)

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction NATURAL CEMENT MORTAR - DIVISION 04

ROSENMIX 350

KING PACKAGED MATERIALS COMPANY

PHL-350

PHL-350 is a pre-blended, pre-packaged mortar specifically designed for use in VAPOUR TRANSMISSION repointing historical building and monument. This mortar is a blend of Pozzolanic ASTM E-96 25 Perms Hydraulic Lime (PHL), an air entraining agent and sand. It is buff in color but can also be blended with a variety of iron pigments. *These figures have been obtained in a lab

FEATURES & BENEFITS OPTIMUM PERFORMANCE • Does not contain cement. • Do not use PHL-350 for the installation of masonry elements. In this case, • Better salt-scaling resistance than hydrated lime. it is recommended to use PHL-500 or HLM-500 mortar. • Excellent vapour-water transmission. • The substrate and mortar temperature should be maintained between 5 and • Low shrinkage. 38 °C (40 and 100 °F) for 72 hours after mortar application. • Pre-blended, ensuring consistency from the first batch to the last. • Never add water to recover lost workability. In this case, simply mix again. • All KING products are manufactured using ISO 9001:2008 • Never use on-site admixtures to modify setting time, workability or any Certified Processes. other properties of plastic or hardened mortar.

USES YIELD • Ideal for repointing buildings originally built before 1920. 30 kg bag contains approximately 0.018m³ (0.65ft³) of fresh mortar. • Can be applied indoors and outdoors, where low compressive strengths are required. PACKAGING King PHL-350 is normally packaged in 30 kg (66 lb) triple lined bags and PROCEDURES poly wrapped on wooden pallets. All KING products can be custom packaged Mixing: to suit specific job requirements. Mix the PHL-350 with a maximum of 4.5 liters (1.18 US gallons) of potable water per 30 kg (66 lb) into a clean mortar mixer. Poor 4 liters (1 US gallon) STORAGE AND SHELF LIFE into the mixer and gradually add the PHL-350. Mix for 3-5 minutes or Material should be stored in a dry, covered area, protected from the elements. 5-10 minutes if an iron pigment has been add. With the remaining water Unopened bags have a shelf life of 12 months. adjust the mix to obtain the desired consistency. SAFETY PROCEDURES Placing: Normal safety-wear such as rubber gloves, dust mask and safety glasses used Clean the area to be repointed, removing all loose material on a thickness to handle conventional cement based products should be worn. Safety Data corresponding to 2 times the thickness of the joint. Moist the area to be Sheets are available upon request. repointed with potable water without leaving stagnant water. Place the PHL-350 into the joint in successive layers to a maximum depth of 6mm Note: The contents of this data sheet are updated regularly. To ensure that you have the most (¼ inch). Compact well and let dry slightly before adding additional layers. recent version, please visit our website at the following address: www.king-masonry.com Tool the joint prior to setting. This product is designed to meet the performance specifications outlined in this product data Curing: sheet. If the product is used in conditions for which it was not intended, or applied in a manner Curing is essential to optimize physical properties of the mortar. After material contrary to the written recommendations contained in the product data sheet, the product may has reached initial set, continuously moist cure for a period of 3 to 7 days. not reach such performance specifications. The foregoing is in lieu of any other warranties, representations or conditions, expressed or implied, including, but not limited to, implied warranties TECHNICAL DATA* or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. VICAT CONE 19 mm V0318

COMPRESSIVE STRENGTH CSA A23.2-8A 7 Day 2.0 MPa (290 psi) 28 Day 3.2 MPa (360 psi) 90 Day 6.4 MPa (650 psi)

AIR CONTENT 18% Maximum WATER RETENTION 75% Minimum

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction REPOINTING MORTAR - DIVISION 04

PHL-350

KING PACKAGED MATERIALS COMPANY

MASONCARE 300

MasonCare 300 is a pre-blended, pre-packaged Type O mortar specifically FLOW designed for use in repointing and non-load-bearing wall applications. This 110 +/- 5 % mortar is a blend of Portland cement, Type S hydrated lime, masonry sand and other carefully selected components. MasonCare 300 conforms to ASTM AIR CONTENT C270 for Type O mortar with the addition of water. It is grey in color, but can 14 % Maximum also be blended with a variety of coloring agents. WATER RETENTION FEATURES & BENEFITS 75 % Minimum • High bond strength. • High vapor transmission properties. VAPOR TRANSMISSION • Superior workability. ASTM E-96 25 Perms • Autogeneous healing properties. • Low strength. BOND STRENGTH • Pre-blended, ensuring consistency from the first batch to the last. CSA A23.2-6B 0.75 MPa (110 psi) • All KING products are manufactured using ISO 9001:2008 Certified Processes. OPTIMUM PERFORMANCE USES • MasonCare 300 should not be used where Type N or S mortar is specified. • Ideal for use in repointing. For applications requiring conventional Type N Mortar, please refer to KING • Can be applied indoors, outdoors or for any other masonry application 1-1-6. For applications requiring conventional Type S Mortar, please refer where low strength and superior workability is required. to KING 2-1-9. • The substrate and mortar temperature should be between 5°C and 38°C PROCEDURES (40°F and 100°F) and maintained in this range for 10 days after mortar Mixing: application. NOTE: If the temperature will be under 0°C in 90 days For best results, add a maximum of 4.3 litres (1.13 US gallon) of potable following the end of the cure, protect the mortar against snow and water water per 30 kg (66 lb.) bag into the mixer. Gradually add MasonCare 300 for the entire period where the temperature will be under 0°C or use the to water and mix with either a paddle or drill mixer, operating until the mix is RosenMix 350. heavy bodied enough to retain it’s shape when fashioned by hand into a ball. • MasonCare 300 should be moisture cured for a period of 3 days. Wait approximately 30 minutes before the application. It is important to mix • Never use on-site admixtures to modify setting time, workability, or any the entire content of the bag. other properties of plastic or hardened mortar. • Use only the recommended water content to achieve the desired plastic Placing: and hardened mortar properties. Clean the area to be repaired, removing all loose material at a thickness corresponding to 2 times the thickness of the joint. Moisten the area to be YIELD repaired with potable water, leaving the old masonry unit saturated but free 30 kg (66 lb.) bag contains approximately 0.018m3 (0.65ft3) of fresh mortar, of standing water (SSD). Place MasonCare 300 into the joint in successive enough to repoint approximately 90 linear meters (300 ft). layers to a maximum depth of 6 mm (¼ inch). Compact well and let dry slightly before adding additional layers. Tool the joints prior to final set time PACKAGING in order to optimize carbonation. MasonCare 300 is normally packaged in 30 kg (66 lb.) triple lined bags and poly wrapped on wooden pallets. All KING products can be custom packaged Curing: to suit specific job requirements. Curing is essential to optimize the physical properties of mortar. Curing is performed by using a wet cure that must start from the initial set of the STORAGE AND SHELF LIFE mortar and continue for a period of three days. Material should be stored in a dry covered area protected from the elements. Unopened bags have a shelf life of 12 months. TECHNICAL DATA The following data is representative of typical values achievable under SAFETY PROCEDURES laboratory conditions according to ASTM C270 for Type O Mortar. Results in MasonCare 300 contains Portland cement and lime. Normal safety-wear the field may vary. such as rubber gloves, dust mask and safety glasses used to handle conventional cement based products should be worn. Material Safety Data COMPRESSIVE STRENGTH Sheets are available upon request. (MINIMUM) 28 day 2.4 MPa (350 psi) Note: The contents of this data sheet are updated regularly. To ensure that you have the most recent version, please visit our website at the following address: www.king-masonry.com

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction TYPE O MORTAR - DIVISION 04

MASONCARE 300

This product is designed to meet the performance specifications outlined in this product data sheet. If the product is used in conditions for which it was not intended, or applied in a manner contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, representations or conditions, expressed or implied, including, but not limited to, implied warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. V0115

KING PACKAGED MATERIALS COMPANY

MASONCARE 1258

The MasonCare 1258 is a pre-blended, pre-packaged mortar specifically OPTIMUM PERFORMANCE designed for use on historical buildings and monuments. This mortar is a • The substrate and mortar temperature should be between 5 and 38°C blend of 1 part of white Portland cement, 2.5 parts of hydrated lime type SA (40 and 100°F) and maintaining in this range for 72 hours after mortar and 8 parts of sand. It is cream in color but can also be blended with a application. variety of iron pigments. • The MasonCare 1258 should be moisture cured for a period of 3 days. • Never use on-site admixtures to modify setting time, workability or any FEATURES & BENEFITS other properties of the plastic or hardened mortar. • Excellent vapor-water transmission. • Superior workability. YIELD • Excellent autogeneous healing properties. • 30 kg bag contains approximately 0.018m³ (0.65ft³) of fresh mortar. One • Pre-blended, ensuring consistency from the first batch to the last. 30 kg bag can repoint approximately 90 linear meters (300 ft) of joint. • Manufactured to meet the ISO 9001:2000 Quality Standards. PACKAGING USES King MasonCare 1258 is normally packaged in 30 kg (66 lb) triple lined • Ideal for repointing historic buildings and monuments. bags and poly wrapped on wooden pallets. All KING products can be custom • Can be applied indoors and outdoors. packaged to suit specific job requirements.

PROCEDURES STORAGE AND SHELF LIFE Mixing: Material should be stored in a dry covered area protected from the elements. For best results, add 3.9 litres (1.0 US gallon) of potable water per 30 kg Unopened bags have a shelf life of 12 months. (66 lb.) bag into the mixer. Gradually add MasonCare 1258 to water and mix with either a paddle or drill mixer, operating until the mix is heavy SAFETY PROCEDURES bodied enough to retain it’s shape when fashioned by hand into a ball. Wait MasonCare 1258 contains Portland cement and lime. Normal safety- approximately 30 minutes before the application. wear such as rubber gloves, dust mask and safety glasses used to handle conventional cement based products should be worn. Material Safety Data Placing: Sheets are available upon request. Clean the area to be repaired, removing all loose material at a thickness corresponding to 2 times the thickness of the joint. Moisten the area to Note: The contents of this data sheet are updated regularly. To ensure that you have the most be repaired with potable water, leaving the concrete saturated but free of recent version, please visit our website at the following address: www.king-masonry.com standing water (SSD). Place MasonCare 1258 into the joint in successive layers to a maximum depth of 6 mm (¼ inch). Compact well and let dry This product is designed to meet the performance specifications outlined in this product data slightly before adding additional layers. Tool the joints prior to final set time sheet. If the product is used in conditions for which it was not intended, or applied in a manner in order to optimize carbonation. contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, TECHNICAL DATA * representations or conditions, expressed or implied, including, but not limited to, implied warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. COMPRESSIVE STRENGTH ASTM C-270 V1016 7 days 2.0 MPa 28 days 4.0 MPa

AIR 14% Maximum

*These figures have been obtained in a lab

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction TYPE O MORTAR - DIVISION 04

MASONCARE 1258

KING PACKAGED MATERIALS COMPANY

RECONSTEC 900 - REPOINTING

Repointing mortar for sandstone, limestone, granite and brick. SURFACE PREPARATION Remove impurities, deteriorated mortar and any other bond inhibiting DESCRIPTION materials from the surface. The joints must be raked and cleaned to a depth Reconstec 900 is a specially formulated mortar for repointing natural stone of at least 1 cm (½ inch) - preferably 2 cm (¾ inch). mortar joints. It is recommended to restore joints at ground level and above grade and where de-icing salts are used during the winter. It is made of a MIXING special hydraulic cement, silica sand, river washed sand and mineral additives. The mixing ratio is approximately 5 parts powder to 1 part water. Use a clean This product does not include a bonding agent and is not polymer integrated. container. Pour water into mixing container. The mixing may be done by hand or using a slow speed drill (300 rpm-450 rpm) with a mixing paddle. The ADVANTAGES mortar should be the consistency of damp sand. Do not add too much water. • High water retention (twice than that of a typical type S hydrated lime Do not over mix. Working time is approximately 15 minutes. based mortar). • Non-shrink (even at bedding consistence for laying brick). APPLICATION & FINISHING • Strong bond capability. Wet the cleaned joints just before applying the mortar, just enough to dampen • No curing required. the surface. Use appropriate pointing tools to achieve a finish similar to the • Not a vapor barrier, completely breathable. original joint profile. The mortar should be firmly pressed to form a packed • Very good freeze-thaw resistance. joint free of voids. • Easy to use. • Pigmented versions available. CLEAN UP Remove the mortar from tools and mixing equipment with water. Cured TECHNICAL DATA material can only be removed mechanically. Application time: Approximately 15 minutes after mixing. Application time is temperature CAUTION dependent. Higher temperatures result in a faster set time, and less available Avoid eyes contact and prolonged contact with skin. May cause irritation to time for application. sensitive skin. In case of skin or eye contact, wash thoroughly with water. Avoid breathing the dust. In case of contact with the eyes, consult a doctor. COMPRESSIVE STRENGTH KEEP OUT OF REACH OF CHILDREN. ASTM C 109 Sandstone Limestone Granite Note: The contents of this data sheet are updated regularly. To ensure that you have the most 28 day (MPa) 2 MPa to 3 MPa 2 MPa to 5 MPa 10 MPa to 16 MPa recent version, please visit our website at the following address: www.king-masonry.com

SPECIFIC GRAVITY This product is designed to meet the performance specifications outlined in this product data Sandstone Limestone Granite sheet. If the product is used in conditions for which it was not intended, or applied in a manner 1.4 1.6 1.8 contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, COVERAGE representations or conditions, expressed or implied, including, but not limited to, implied lineal metre warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. Sandstone Limestone Granite 142 m 125 m 110 m V1116 (10 mm joints at 10 mm deep per 20 kg pail.)

PACKAGING One plastic pail contains 20 kg (44 lb).

MIXING RATIO The mixing ratio is approximately 5 parts powder to 1 part water by volume.

FINISHING TIME Approximately 30 minutes after mixing, depending on temperature, relative humidity and the type of finish desired.

SHELF LIFE 1 year in original, unopened pail.

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 900 - REPOINTING

RECONSTEC 900 - REPOINTING

KING PACKAGED MATERIALS COMPANY

HL-5 GROUT

HL-5 grout is a pre-blended, pre-packaged hydraulic lime based injection • Never use on-site admixtures to modify setting time, workability, or any grout specifically designed for consolidation or the filling of voids in historical other properties of plastic or hardened grout. masonry walls and foundations. HL-5 is a blend of natural hydraulic lime • Only use the recommended amount of water to obtain the plastic and (St-Astier) and other carefully selected components. hardened properties of the grout. • For optimum flow performance, a high shear mixer should be used. FEATURES & BENEFITS However, a high speed drill can be used. The flowability of the product • Can be pumped or gravity fed. may be different than on the technical data sheet. • Can be applied indoors and outdoors. • Extremely fluid with no segregation and no bleeding. YIELD • Excellent bond strength. 20 kg (44lb.) bag contains approximately 0.02 m3 (0.66 ft3) of fresh grout. • Pre-blended, ensuring consistency from the first batch to the last. • All KING products are manufactured using ISO 9001:2008 Certified PACKAGING Processes. HL-5 grout is normally packaged in 20kg (44lb.) triple line bags, poly wrapped on wooden pallets. All KING products can be custom packaged to USES suit specific job requirements. KING HL-5 injection grout is specifically designed for consolidating and filling voids in historical masonry walls and foundations. STORAGE AND SHELF LIFE Material should be stored in a dry covered area protected from the elements. PROCEDURES Unopened bags have a shelf life of 12 months. Mixing: HL-5 grout should be mixed with a maximum of 13.5 litres (3.4 US gallons) SAFETY PROCEDURES of potable water per 20 kg (44lb.) bag. Add 10 litres (2.6 US gallons) of HL-5 Grout contains natural hydraulic lime (St-Astier). Normal safety- water into a high shear mixer along with one 20 kg (44lb) bag of HL-5 grout wear such as rubber gloves, dust mask and safety glasses used to handle and mix 3-5 minutes. Use the remaining water to adjust the mix in order to conventional cement based products should be worn. Material Safety Data obtain the desired consistency. Sheets are available upon request.

Placing: Note: The contents of this data sheet are updated regularly. To ensure that you have the most Make sure that all masonry joints are tight. Install injection tubes horizontally recent version, please visit our website at the following address: www.king-masonry.com and vertically every 300 mm. Start injecting from the bottom. Once the grout starts to flow out of the above port, switch to that port and plug the bottom This product is designed to meet the performance specifications outlined in this product data port. The grout should be agitated regularly. sheet. If the product is used in conditions for which it was not intended, or applied in a manner contrary to the written recommendations contained in the product data sheet, the product may TECHNICAL DATA not reach such performance specifications. The foregoing is in lieu of any other warranties, The following data is representative of typical values achievable under representations or conditions, expressed or implied, including, but not limited to, implied laboratory conditions. Results in the field may vary. warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. COMPRESSIVE STRENGTH V0117 7 day 2.5 MPa (365 psi) 28 day 4.0 MPa (580 psi) 90 day 5.0 MPa (725 psi)

BLEEDING & SEGREGATION 0% FLOW ASTM C 942 10-30 seconds

OPTIMUM PERFORMANCE • HL-5 grout should not be used as a bedding mortar for masonry units. For applications requiring bedding of masonry units, please refer to KING masonry mortars. • The substrate and grout temperature should be between 5°C and 38°C (40°F and 100°F) and maintained in this range for 10 days after the grout application.

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction MASONRY GROUT - DIVISION 04

HL-5 GROUT

KING PACKAGED MATERIALS COMPANY

KING LS

KING LS is a pre-blended, pre-packaged grout, with low compressive strength, OPTIMUM PERFORMANCE specifically designed for injection, in order to replace or in addition of existing • KING LS should not be used as a bedding mortar for masonry units. For mortar or grout, into masonry affected by movements or any type of loss. This applications requiring bedding of masonry units, please refer to KING mix is a blend of cementitious material, masonry sand and other carefully masonry mortars. selected components. • The substrate and mortar temperature should be between 5°C and 38°C (40°F and 100°F) and maintained in this range for 72 hours after the FEATURES & BENEFITS grout application. • Low compressive strength. • Never use on-site admixtures to modify setting time, workability, or any • Can be poured, pumped or injected. other properties of plastic or hardened grout. • Can be used indoors or outdoors. • Only use the recommended amount of water to obtain the plastic or • Economical. hardened properties of the grout. • Pre-blended, ensuring consistency from the first batch to the last. • All KING products are manufactured using ISO 9001:2008 Certified YIELD Processes. 30 kg (66 lb.) bag contains approximately 0.018 m3 (0.65 ft3) of fresh grout.

USES PACKAGING • KING LS is a grout specifically designed to fill voids in masonry walls. Its KING LS is normally packaged in 30 kg (66 lb.) triple lined bags or bulk low density minimizes the impact of injection into the building envelope. bags , poly wrapped on wooden pallets. All KING products can be custom packaged to suit specific job requirements. PROCEDURES Mixing: STORAGE AND SHELF LIFE KING LS should be mixed with a maximum of 6.6 litres Material should be stored in a dry, covered area protected from the elements. (1.7 US gallon) of potable water per 30 kg (66 lb.) bag. In a clean container, Unopened bags have a shelf life of 12 months. pour 5.5 litres (1.5 US gallon) of water, then add the contents of the bag while mixing with a drill with a “Jiffler” type mixer (see:www.jifflermixer. SAFETY PROCEDURES com) mixing tip. It is important to mix the entire content of the bag. If KING LS grout contains cement. Normal safety-wear such as rubber gloves, necessary, add remaining water until obtaining a mixture with enough fluidity dust mask and safety glasses used to handle conventional cement based for injection. products should be worn. Material Safety Data Sheets are available upon request. Placing: Make sure that all masonry joints are tight. Install injection tubes horizontally Note: The contents of this data sheet are updated regularly. To ensure that you have the most and vertically every 300 mm (12 in). Start injecting from the bottom. Once recent version, please visit our website at the following address: www.king-masonry.com the grout starts to flow out of the above port, switch to that port and plug the bottom port. The grout should be agitated regularly. This product is designed to meet the performance specifications outlined in this product data sheet. If the product is used in conditions for which it was not intended, or applied in a manner Note: This product contains sand. Injection tubes should be chosen taking contrary to the written recommendations contained in the product data sheet, the product may this in consideration. not reach such performance specifications. The foregoing is in lieu of any other warranties, representations or conditions, expressed or implied, including, but not limited to, implied TECHNICAL DATA warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. The following data is representative of typical values achievable under laboratory conditions. Results in the field may vary. V1014

COMPRESSIVE STRENGTH ASTM- C109 7 Day 3.5 MPa (510 psi) 28 Day < 10.0 MPa (1450 psi)

BLEEDING AND SEGREGATION ASTM C 940 < 2 % MINIMUM SLUMP FLOW 100 to 200 mm

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction MASONRY GROUT - DIVISION 04

KING LS

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction GROUT - DIVISION 04

RPL-6

The RPL-6 is a pre-blended, pre-packaged low compressive strength grout, YIELD specifically designed for injection into masonry structures affected by movement 0.019m³ (0.67 ft³) or any type of section loss. RPL-6 grout can be used in replacement or in addition to an existing mortar or grout used in a masonry structure. The RPL-6 is composed of Portland cement, hydrated type S lime, sand and other carefully OPTIMUM PERFORMANCE selected components. • The RPL-6 should not be used as a bedding mortar for masonry units. For applications requiring bedding of masonry units, please refer to KING FEATURES & BENEFITS masonry mortars. • High fluidity. • The substrate and the grout temperature should be between 5°C and 38°C • Low compressive strength. (40°F and 100°F) and maintained in this range for 72 hours after the grout • Can be poured, pumped or injected. application. • Can be used indoors or outdoors. • Never use on-site admixtures to modify setting time, workability, or any • Economic. other properties of plastic or hardened grout. • Pre-blended, ensuring consistency from the first batch to the last. • Only use the recommended amount of water to obtain the plastic or hardened • All KING products are manufactured using ISO 9001:2008 properties of the grout. Certified Processes. YIELD USES 30 kg bag contains approximately 0.019 m3 (0.67 ft3) of grout. The RPL-6 is specifically designed to fill voids in masonry walls and foundations. The low plastic density of the RPL-6 minimizes the impact of injection on the PACKAGING building envelope. The high fluidity coupled with the small maximum particle The RPL-6 is normally packaged in 30 kg triple lined bags or non-returnable size allows RPL-6 to easily infiltrate into small openings bulk bags, and poly wrapped on wooden pallets. All KING products can be custom packaged to suit specific job requirements. PROCEDURES Mixing: STORAGE AND SHELF LIFE The RPL-6 should be mixed with a maximum of 8.5 liters (2.25 US gallons) Material should be stored in a dry covered area protected from the elements. of potable water per 30 kg (66 lb.) bag. In a clean container, pour 7.5 liters Unopened bags have a shelf life of 12 months. (2.00 US gallons) of water then add the contents of the bag while mixing with a drill equipped with a “Jiffler” type mixing tip (see:www.jifflermixer.com). SAFETY PROCEDURES It is important to mix the entire contents of the bag. If necessary, add the This product contains cement. Normal safety-wear such as rubber gloves, dust remaining water until the mixture is fluid enough for injection. mask and safety glasses used to handle conventional cement based products should be worn. Safety Data Sheets are available upon request. Placing: Make sure that all masonry joints are tight. Install injection tubes horizontally Note: The contents of this data sheet are updated regularly. To ensure that you have the most and vertically every 300 mm (1 ft). Start injecting from the bottom. Once the recent version, please visit our website at the following address: www.king-masonry.com grout starts to flow out of the above port, switch to that port and plug the bottom port. The grout should be agitated regularly. This product is designed to meet the performance specifications outlined in this product data sheet. Note: The RPL-6 contains sand. The injection tube diameter must be If the product is used in conditions for which it was not intended, or applied in a manner contrary considered prior to pumping. to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, representations TECHNICAL DATA or conditions, expressed or implied, including, but not limited to, implied warranties or conditions The following data is representative of typical values achievable under laboratory of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. conditions. Results in the field may vary. V0217 COMPRESSIVE STRENGTHS (MINIMUM) ASTM- C109 7 Day 3.5 MPa (425 psi) 28 Day 5.0 MPa (725 psi)

BLEEDING & SEGREGATION ASTM C-940 2% FLOW ASTM C-939 10-30 seconds

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction GROUT - DIVISION 04

RPL-6

KING PACKAGED MATERIALS COMPANY

RECONSTEC 700 - INJECTION GROUT

Injection grout. SURFACE PREPARATION The surface must be clean and solid. It can be dry or wet. Remove all DESCRIPTION impurities, dirt, grease, and other bond inhibiting materials from the surface. Reconstec 700 is a cement based, high performance, specially designed Preparation work should be done using manual or pneumatic cutting grout for injection into cracks ranging from 1.5 mm to 2.5 mm. The grout techniques. Set appropriate injection ports. Seal the cracks and the injection is to be used in the stabilization and rehabilitation of cracked masonry ports with the appropriate Reconstec mortar. and concrete. Non-shrink with very good bonding properties to substrates. Contains no synthetic polymers. MIXING The mixing ratio is approximately 4 parts powder to 1 part water. Use a clean ADVANTAGES container. Pour water into mixing container. The mixing may be done by hand • Gravity-feed or pressure-injection. or using a slow speed drill (300 rpm-450 rpm) with a mixing paddle. The • Deep penetrating and tenacious bonding of cracks. grout should be the consistency of syrup. Do not add too much water initially • Very good adhesion to dry or wet substrates. during mixing. Do not over mix. Working time is approximately 10 minutes. • Not a vapor barrier, completely breathable. • Excellent fluidity. APPLICATION & FINISHING • No shrinkage. For injection work, use plastic cartridges. Inject grout to the lowest port and • No sedimentation. proceed upwards. The grout is injected into a series of injection ports along • Easy to use. the length of crack. Injection continues at a given port until it flows out of the • Rapid set. next one. The port is then sealed off and injection is started at the next port • Non-corrosive. and so on until the full length of the crack has been treated. Remove ports • Pigmented versions available. after curing and patch with the appropriate Reconstec mortar.

TECHNICAL DATA CLEAN UP Application time: Remove the mortar from tools and mixing equipment with water. Cured Approximately 15 minutes after mixing. Application time is dependent on material can only be removed mechanically. temperature. Higher temperature will require a faster application than with cooler temperatures. CAUTION Avoid eyes contact and prolonged contact with skin. May cause irritation to COMPRESSIVE STRENGTH sensitive skin. In case of skin or eye contact, wash thoroughly with water. ASTM C 109 Avoid breathing the dust. In case of contact with the eyes, consult a doctor. 28 day 50 MPa (7300 psi) KEEP OUT OF REACH OF CHILDREN.

TENSILE BONDING STRENGTH Note: The contents of this data sheet are updated regularly. To ensure that you have the most ASTM C 882 10 MPa (1500 psi) recent version, please visit our website at the following address: www.king-masonry.com

VISCOSITY This product is designed to meet the performance specifications outlined in this product data 600-1000 cps sheet. If the product is used in conditions for which it was not intended, or applied in a manner contrary to the written recommendations contained in the product data sheet, the product may MIXING RATIO not reach such performance specifications. The foregoing is in lieu of any other warranties, The mixing ratio is approximately 4 parts powder to 1 part water by volume. representations or conditions, expressed or implied, including, but not limited to, implied warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. DENSITY 2,000 kg / m3 V1014

PACKAGING One plastic pail contains 20 kg (44 lb).

SHELF LIFE 1 year in original, unopened pail.

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 700 - INJECTION GROUT

RECONSTEC 700 - INJECTION GROUT

KING PACKAGED MATERIALS COMPANY

RECONSTEC 700F - INJECTION GROUT

Injection grout. SURFACE PREPARATION The surface must be clean and solid. It can be dry or wet. Remove all DESCRIPTION impurities, dirt, grease, and other bond inhibiting materials from the surface. Reconstec 700F is a cement based, high performance, specially designed Preparation work should be done using manual or pneumatic cutting grout for injection into cracks ranging from 0.5 mm to 2 mm. The grout techniques. Set appropriate injection ports. Seal the cracks and the injection is to be used in the stabilization and rehabilitation of cracked masonry ports with the appropriate Reconstec mortar. and concrete. Non-shrink with very good bonding properties to substrates. Contains no synthetic polymers. MIXING The mixing ratio is approximately 4 parts powder to 1 part water. Use a clean ADVANTAGES container. Pour water into mixing container. The mixing may be done by • Gravity-feed or pressure-injection. hand or using a slow speed drill (300 rpm-450 rpm) with a mixing paddle. • Deep penetrating and tenacious bonding of cracks. The grout should be the consistency of syrup. Do not add too much water • Very good adhesion to dry or wet substrates. at the beginning of mixing. Do not over mix. Working time is approximately • Not a vapor barrier, completely breathable. 10 minutes. • Excellent fluidity. • No shrinkage. APPLICATION & FINISHING • No sedimentation. When injecting, choose plastic cartridges. Inject grout to the lowest port and • Easy to use. proceed upwards. The grout is injected into a series of injection ports along • Rapid set. the length of crack. Injection continues at a given port until it flows out of the • Non-corrosive. next one. The port is then sealed off and injection started at the next port and • Pigmented versions available. so on until the full length of the crack has been treated. Remove ports after curing and patch with the appropriate reconstec mortar. TECHNICAL DATA Application time: CLEAN UP Approximately 10 minutes after mixing. Application time is temperature Remove the mortar from tools and mixing equipment with water. Cured dependent. Higher temperatures result in a faster set vs lower temperatures. material can only be removed mechanically.

COMPRESSIVE STRENGTH CAUTION ASTM C 109 Avoid eyes contact and prolonged contact with skin. May cause irritation to 28 day 50 MPa (7300 psi) sensitive skin. In case of skin or eye contact, wash thoroughly with water. Avoid breathing the dust. In case of contact with the eyes, consult a doctor. TENSILE BENDING STRENGTH KEEP OUT OF REACH OF CHILDREN. ASTM C 882 10 MPa (1500 psi) Note: The contents of this data sheet are updated regularly. To ensure that you have the most VISCOSITY recent version, please visit our website at the following address: www.king-masonry.com 600-1000 cps This product is designed to meet the performance specifications outlined in this product data MIXING RATIO sheet. If the product is used in conditions for which it was not intended, or applied in a manner The mixing ratio is approximately 4 parts powder to 1 part water by volume. contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, DENSITY representations or conditions, expressed or implied, including, but not limited to, implied 2,000 kg / m3 warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. PACKAGING V1014 One plastic pail contains 20 kg (44 lb).

SHELF LIFE 1 year in original, unopened pail.

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 700F - INJECTION GROUT

RECONSTEC 700F - INJECTION GROUT

KING PACKAGED MATERIALS COMPANY

RECONSTEC 700M - INJECTION GROUT

Injection grout. SURFACE PREPARATION The surface must be clean and solid. It can be dry or wet. Remove all DESCRIPTION impurities, dirt, grease, and other bond inhibiting materials from the surface. Reconstec 700M is a cement based, high performance, specially designed Preparation work should be done using manual or pneumatic cutting grout for injection into cracks ranging from 2.5 mm to 5 mm. The grout techniques. Set appropriate injection ports. Seal the cracks and the injection is to be used in the stabilization and rehabilitation of cracked masonry ports with the appropriate Reconstec mortar. and concrete. Non-shrink with very good bonding properties to substrates. Contains no synthetic polymers. MIXING The mixing ratio is approximately 4 parts powder to 1 part water. Use a clean ADVANTAGES container. Pour water into mixing container. The mixing may be done by hand • Gravity-feed or pressure-injection. or using a slow speed drill (300 rpm-450 rpm) with a mixing paddle. The • Deep penetrating and tenacious bonding of cracks. grout should be the consistency of syrup. Do not add too much water initially. • Very good adhesion to dry or wet substrates. Do not over mix. Working time is approximately 10 minutes. • Not a vapor barrier, completely breathable. • Excellent fluidity. APPLICATION & FINISHING • Non-shrink. For injection work, use plastic cartridges. Inject grout to the lowest port and • No sedimentation. proceed upwards. The grout is injected into a series of injection ports along • Easy to use. the length of the crack. Injection continues at a given port until it flows out of • Rapid set. the next one. The port is then sealed off and injection is started at the next • Non-corrosive. port and so on until the full length of the crack has been treated. Remove • Pigmented versions available. ports after curing and patch with the appropriate Reconstec Mortar.

TECHNICAL DATA CLEAN UP Application time: Remove the mortar from tools and mixing equipment with water. Cured Approximately 10 minutes after mixing. Application time is temperature material can only be removed mechanically. dependent. Higher temperatures result in a quicker set, and less time allowed for application of product CAUTION Avoid eyes contact and prolonged contact with skin. May cause irritation to COMPRESSIVE STRENGTH sensitive skin. In case of skin or eye contact, wash thoroughly with water. ASTM C 109 Avoid breathing the dust. In case of contact with the eyes, consult a doctor. 28 day 50 MPa (7300 psi) KEEP OUT OF REACH OF CHILDREN.

PACKAGING One plastic pail contains 20 kg (44 lb).

SHELF LIFE 1 year in original, unopened pail.

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 700M - INJECTION GROUT

RECONSTEC 700M - INJECTION GROUT

KING PACKAGED MATERIALS COMPANY

RECONSTEC 100 - GRANITE

Granite restoration mortar. FINISHING TIME Approximately 2 hours after mixing. Finishing time will depend on DESCRIPTION temperature of substrate, humidity and type of finish desired. Reconstec 100 is a mortar specially designed for the restoration of granite. Non-shrink with a very good bond to granite. Easily applied to clean, sound PACKAGING substrates. May be feather edged. Contains no synthetic polymers. One plastic pail contains 20 kg (44 lb).

ADVANTAGES SHELF LIFE • The same coefficient of thermal expansion as granite. 1 year in original, unopened pail. • Uses Granite aggregate. • Very good adhesion to substrates. • Not a vapor barrier, completely breathable. SURFACE PREPARATION • Good freeze-thaw resistance. Remove all impurities, dirt, grease, and other bond inhibiting materials from • Easy to use. the surface. Preparation work should be done using manual or pneumatic • Short curing time. cutting techniques. Dampen surface to be repaired with clean water. • Pigmented versions available. MIXING TECHNICAL DATA The mixing ratio is approximately 5 parts powder to 1 part water. Use a clean Application time: container. Pour water into mixing container. The mixing may be done by hand Approximately 15 minutes after mixing. Application time is dependent on or using a slow speed drill (300 rpm-450 rpm) with a mixing paddle. The temperature. Higher temperature will require a faster application than with mortar should be the consistency of damp sand. Do not add too much water. cooler temperatures. Do not over mix. Working time is approximately 15 minutes.

COMPRESSIVE STRENGTH APPLICATION & FINISHING ASTM C 109 Mortar must be scrubbed into substrate, filling all pores and voids. Use a 1 day 40 MPa (5800 psi) steel trowel. Force material against edge of repair, working toward the centre. 7 day 80 MPa (11600 psi) For best results use Reconstec 100 without aggregate as a first layer. When 28 day 90 MPa (13100 psi) the mortar is hard use stone cutting tools to achieve desired finish.

FLEXURAL STRENGTH CURING ASTM C 348 14.5 MPa (2103 psi) Curing is not necessary.

MODULUS OF ELASTICITY CLEAN UP ASTM C 469 27.5 GPa (4000000 psi) Remove the mortar from tools and mixing equipment with water. Cured material can only be removed mechanically. BOND STRENGTH ASTM C 882 (MODIFIED) CAUTION 13.3 MPa (1930 psi) Avoid eyes contact and prolonged contact with skin. May cause irritation to sensitive skin. In case of skin or eye contact, wash thoroughly with water. LINEAR COEFF. OF THERMAL EXPANSION Avoid breathing the dust. In case of contact with the eyes, consult a doctor. 7 to 8 x 10-6/°C KEEP OUT OF REACH OF CHILDREN.

LENGTH CHANGE Note: The contents of this data sheet are updated regularly. To ensure that you have the most ASTM C 157 0.005 to 0.010 % (28 day) recent version, please visit our website at the following address: www.king-masonry.com

ABSORPTION This product is designed to meet the performance specifications outlined in this product data 0.5 to 1.5 % sheet. If the product is used in conditions for which it was not intended, or applied in a manner contrary to the written recommendations contained in the product data sheet, the product may SPECIFIC GRAVITY not reach such performance specifications. The foregoing is in lieu of any other warranties, 2.2 representations or conditions, expressed or implied, including, but not limited to, implied warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. MIXING RATIO The mixing ratio is approximately 5 parts powder to 1 part water by volume. V1014

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 100 - GRANITE

RECONSTEC 100 - GRANITE

KING PACKAGED MATERIALS COMPANY

RECONSTEC 200 - SANDSTONE

Sandstone restoration mortar. PACKAGING One plastic pail contains 20 kg (44 lb). DESCRIPTION Reconstec 200 is a mortar specially designed for the restoration of sandstone. SHELF LIFE Non-shrink with a very good bond to sandstone. Easily applied to clean, 1 year in original, unopened pail. sound substrates. May be feather edged. Contains no synthetic polymers.

ADVANTAGES SURFACE PREPARATION • The same coefficient of thermal expansion as sandstone. Remove all impurities, dirt, grease, and other bond inhibiting materials from • Very good adhesion to substrates. the surface. Preparation work should be done using manual or pneumatic • Not a vapor barrier, completely breathable. cutting techniques. Dampen surface to be repaired with clean water. • Good freeze-thaw resistance. • Easy to use. MIXING • No curing. The mixing ratio is approximately 5 parts powder to 1 part water. Use a clean • Pigmented versions available. container. Pour water into mixing container. The mixing may be done by hand or using a slow speed drill (300 rpm-450 rpm) with a mixing paddle. The TECHNICAL DATA mortar should be the consistency of damp sand. Do not add too much water. Application time: Do not over mix. Working time is approximately 15 minutes. Approximately 15 minutes after mixing. Application time is dependent on temperature. Higher temperature will require a faster application than with APPLICATION & FINISHING cooler temperatures. Mortar must be scrubbed into substrate, filling all pores and voids. Use a steel trowel. Force material against edge of repair, working toward the centre. COMPRESSIVE STRENGTH When the mortar is the consistency of dry sand, screed to desired finish. ASTM C 109 1 day 12 MPa (1750 psi) CURING 7 day 25 MPa (3600 psi) Curing is not necessary. 28 day 30 MPa (4350 psi) CLEAN UP FLEXURAL STRENGTH Remove the mortar from tools and mixing equipment with water. Cured ASTM C 348 8.5 MPa (1233 psi) material can only be removed mechanically.

MODULUS OF ELASTICITY CAUTION ASTM C 469 11.7 to 12.8 GPa Avoid eyes contact and prolonged contact with skin. May cause irritation to (1700000 to 1850000 psi) sensitive skin. In case of skin or eye contact, wash thoroughly with water. Avoid breathing the dust. In case of contact with the eyes, consult a doctor. BOND STRENGTH KEEP OUT OF REACH OF CHILDREN. ASTM C 882 (MODIFIED) 11.2 MPa (1625 psi) Note: The contents of this data sheet are updated regularly. To ensure that you have the most recent version, please visit our website at the following address: www.king-masonry.com LINEAR COEFF. OF THERMAL EXPANSION 10.5 to 11.5 x 10-6/°C This product is designed to meet the performance specifications outlined in this product data sheet. If the product is used in conditions for which it was not intended, or applied in a manner LENGTH CHANGE contrary to the written recommendations contained in the product data sheet, the product may ASTM C 157 0.005 to 0.010 % (28 day) not reach such performance specifications. The foregoing is in lieu of any other warranties, representations or conditions, expressed or implied, including, but not limited to, implied SPECIFIC GRAVITY warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. 1.6 V1014 MIXING RATIO The mixing ratio is approximately 5 parts powder to 1 part water by volume.

FINISHING TIME Approximately 1 hour after mixing. Finishing time will depend on temperature of substrate, humidity and type of finish desired.

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 200 - SANDSTONE

RECONSTEC 200 - SANDSTONE

KING PACKAGED MATERIALS COMPANY

RECONSTEC 250 - SANDSTONE

Sandstone restoration mortar. FINISHING TIME Approximately 1 hour after mixing. Finishing time will depend on temperature DESCRIPTION of substrate, humidity and type of finish desired. Reconstec 250 is a mortar specially designed for the restoration of sandstone. Non-shrink with a very good bond to sandstone. Easily applied to clean, PACKAGING sound substrates. Contains no synthetic polymers. One plastic pail contains 20 kg (44 lb).

ADVANTAGES SHELF LIFE • The same coefficient of thermal expansion as sandstone. 1 year in original, unopened pail. • Very good adhesion to substrates. • Not a vapor barrier, completely breathable. • Good freeze-thaw resistance. SURFACE PREPARATION • Easy to use. Remove all impurities, dirt, grease, and other bond inhibiting materials from • Pigmented versions available. the surface. Preparation work should be done using manual or pneumatic cutting techniques. Be sure patch area is not less 10 mm (½ inch) in depth. TECHNICAL DATA Dampen surface to be repaired with clean water. Application time: Approximately 1 hour after mixing. Application time is dependent on MIXING temperature. Higher temperature will require a faster application than with The mixing ratio is approximately 5 parts powder to 1 part water. Use a clean cooler temperatures. container. Pour water into mixing container. The mixing may be done by hand or using a slow speed drill (300 rpm-450 rpm) with a mixing paddle. The COMPRESSIVE STRENGTH mortar should be the consistency of damp sand. Do not add too much water. ASTM C 109 Do not over mix. Working time is approximately 1 hour. 3 day 12 MPa (1750 psi) 7 day 18 MPa (2600 psi) APPLICATION & FINISHING 28 day 26 MPa (3780 psi) Mortar must be scrubbed into substrate, filling all pores and voids. Use a steel trowel. Force material against edge of repair, working toward the centre. FLEXURAL STRENGTH When the mortar is the consistency of dry sand, screed to desired finish. ASTM C 348 8.5 MPa (1233 psi) CURING MODULUS OF ELASTICITY Spray/mist the surface with clean water for at least 3 days after installation, ASTM C 469 11.7 to 12.8 GPa several times a day. (1700000 to 1850000 psi) CLEAN UP BOND STRENGTH Remove the mortar from tools and mixing equipment with water. Cured ASTM C 882 (MODIFIED) material can only be removed mechanically. 11.2 MPa (1625 psi) CAUTION LINEAR COEFF. OF THERMAL EXPANSION Avoid eyes contact and prolonged contact with skin. May cause irritation to 10.5 to 11.5 x 10-6/°C sensitive skin. In case of skin or eye contact, wash thoroughly with water. Avoid breathing the dust. In case of contact with the eyes, consult a doctor. LENGTH CHANGE KEEP OUT OF REACH OF CHILDREN. ASTM C 157 0.005 to 0.010 % (28 day) Note: The contents of this data sheet are updated regularly. To ensure that you have the most SPECIFIC GRAVITY recent version, please visit our website at the following address: www.king-masonry.com 1.6 This product is designed to meet the performance specifications outlined in this product data POROSITY sheet. If the product is used in conditions for which it was not intended, or applied in a manner 16 % contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, MIXING RATIO representations or conditions, expressed or implied, including, but not limited to, implied The mixing ratio is approximately 5 parts powder to 1 part water by volume. warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. V1014

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 250 - SANDSTONE

RECONSTEC 250 - SANDSTONE

KING PACKAGED MATERIALS COMPANY

RECONSTEC 300 - LIMESTONE

Limestone restoration mortar. FINISHING TIME Approximately 1 hour after mixing. Finishing time will depend on temperature, DESCRIPTION relative humidity. Reconstec 300 is a mortar specially designed for the restoration of limestone. Non-shrink with a very good bond to limestone. Easily applied to clean, PACKAGING sound substrates. May be feather edged. Contains no synthetic polymers. One plastic pail contains 20 kg (44 lb).

TECHNICAL DATA MIXING Application time: The mixing ratio is approximately 5 parts powder to 1 part water. Use a clean Approximately 15 minutes after mixing. Application time is dependent on container. Pour water into mixing container. The mixing may be done by hand temperature. Application time will need to be faster in higher temperatures, or using a slow speed drill (300 rpm-450 rpm) with a mixing paddle. The than in cooler temperatures. mortar should be the consistency of damp sand. Do not add too much water. Do not over mix. Working time is approximately 15 minutes. COMPRESSIVE STRENGTH ASTM C 109 APPLICATION & FINISHING 1 day 15 MPa (2180 psi) Mortar must be scrubbed into substrate, filling all pores and voids. Use a 7 day 30 MPa (4360 psi) steel trowel. Force material against edge of repair, working toward the center. 28 day 35 MPa (5100 psi) When the mortar is the consistency of dry sand, screed to desired finish.

FLEXURAL STRENGTH CURING ASTM C 348 10.9 MPa (1581 psi) Curing is not necessary.

MODULUS OF ELASTICITY CLEAN UP ASTM C 469 13.8 to 16.5 GPa Remove the mortar from tools and mixing equipment with water. Cured (2000000 to 2400000 psi) material can only be removed mechanically.

BOND STRENGTH CAUTION ASTM C 882 (MODIFIED) Avoid eyes contact and prolonged contact with skin. May cause irritation to 11.5 MPa (1670 psi) sensitive skin. In case of skin or eye contact, wash thoroughly with water. Avoid breathing the dust. In case of contact with the eyes, consult a doctor. LINEAR COEFF. OF THERMAL EXPANSION KEEP OUT OF REACH OF CHILDREN. 3.6 to 4.6 x 10-6/°C Note: The contents of this data sheet are updated regularly. To ensure that you have the most LENGTH CHANGE recent version, please visit our website at the following address: www.king-masonry.com ASTM C 157 0.005 to 0.010 % (28 day) This product is designed to meet the performance specifications outlined in this product data SPECIFIC GRAVITY sheet. If the product is used in conditions for which it was not intended, or applied in a manner 1.8 contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, POROSITY representations or conditions, expressed or implied, including, but not limited to, implied 10 % warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. MIXING RATIO V1014 The mixing ratio is approximately 5 parts powder to 1 part water by volume.

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 300 - LIMESTONE

RECONSTEC 300 - LIMESTONE

KING PACKAGED MATERIALS COMPANY

RECONSTEC 350 - LIMESTONE

Limestone restoration mortar. FINISHING TIME Approximately 1 hour after mixing. Finishing time will depend on temperature DESCRIPTION of substrate, humidity and type of finish desired. Reconstec 350 is a mortar specially designed for the restoration of limestone. Non-shrink with a very good bond to limestone. Easily applied to clean, PACKAGING sound substrates. Contains no synthetic polymers. One plastic pail contains 20 kg (44 lb).

ADVANTAGES SHELF LIFE • The same coefficient of thermal expansion as limestone. 1 year in original, unopened pail. • Very good adhesion to substrates. • Not a vapor barrier, completely breathable. • Good freeze-thaw resistance. SURFACE PREPARATION • Easy to use. Remove all impurities, dirt, grease, and other bond inhibiting materials from • Pigmented versions available. the surface. Preparation work should be done using manual or pneumatic cutting techniques. Be sure patch area is not less 10 mm (½ inch) depth. TECHNICAL DATA Dampen surface to be repaired with clean water. Application time: Approximately 1 hour after mixing. Application time is dependent on MIXING temperature. Higher temperature will require a faster application than with The mixing ratio is approximately 5 parts powder to 1 part water. Use a clean cooler temperatures. container. Pour water into mixing container. The mixing may be done by hand or using a slow speed drill (300 rpm-450 rpm) with a mixing paddle. The COMPRESSIVE STRENGTH mortar should be the consistency of damp sand. Do not add too much water. ASTM C 109 Do not over mix. Working time is approximately 1 hour. 3 day 15 MPa (2180 psi) 7 day 22 MPa (3200 psi) APPLICATION & FINISHING 28 day 30 MPa (4360 psi) Mortar must be scrubbed into substrate, filling all pores and voids. Use a steel trowel. Force material against edge of repair, working toward the center. FLEXURAL STRENGTH When the mortar is the consistency of dry sand, screed to desired finish. ASTM C 348 10.9 MPa (1581 psi) CURING MODULUS OF ELASTICITY Spray surface with a mist of clean water for at least 3 days after installation, ASTM C 469 13.1 to 14.5 GPa several times a day. (1900000 to 2100000 psi) CLEAN UP BOND STRENGTH Remove the mortar from tools and mixing equipment with water. Cured ASTM C 882 (MODIFIED) material can only be removed mechanically. 10.4 MPa (1508 psi) CAUTION LINEAR COEFF. OF THERMAL EXPANSION Avoid eyes contact and prolonged contact with skin. May cause irritation to 3.6 to 4.6 x 10-6/°C sensitive skin. In case of skin or eye contact, wash thoroughly with water. Avoid breathing the dust. In case of contact with the eyes, consult a doctor. LENGTH CHANGE KEEP OUT OF REACH OF CHILDREN. ASTM C 157 0.015 to 0.020 % (28 day) Note: The contents of this data sheet are updated regularly. To ensure that you have the most SPECIFIC GRAVITY recent version, please visit our website at the following address: www.king-masonry.com 1.8 This product is designed to meet the performance specifications outlined in this product data POROSITY sheet. If the product is used in conditions for which it was not intended, or applied in a manner 10 % contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, MIXING RATIO representations or conditions, expressed or implied, including, but not limited to, implied The mixing ratio is approximately 5 parts powder to 1 part water by volume. warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. V1014

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 350 - LIMESTONE

RECONSTEC 350 - LIMESTONE

KING PACKAGED MATERIALS COMPANY

RECONSTEC 400 - TERRA COTTA

Terra Cotta restoration mortar. APPLICATION & FINISHING Mortar must be scrubbed into substrate, filling all pores and voids. Use a DESCRIPTION steel trowel. Force material against edge of repair, working toward the center. Reconstec 400 is a mortar specially designed for the restoration of Terra When the mortar is the consistency of dry sand, screed to desired finish. Cotta. Non-shrink with a very good bond to Terra Cotta. Easily applied to clean, sound substrates. May be feather edged. Contains no synthetic CURING polymers. Curing is not necessary.

ADVANTAGES CLEAN UP • The same coefficient of thermal expansion as Terra Cotta. Remove the mortar from tools and mixing equipment with water. Cured • Very good adhesion to substrates. material can only be removed mechanically. • Not a vapor barrier, completely breathable. • Good freeze-thaw resistance. CAUTION • Easy to use. Avoid eyes contact and prolonged contact with skin. May cause irritation to • No curing required. sensitive skin. In case of skin or eye contact, wash thoroughly with water. • Pigmented versions available. Avoid breathing the dust. In case of contact with the eyes, consult a doctor. KEEP OUT OF REACH OF CHILDREN. TECHNICAL DATA Application time: Note: The contents of this data sheet are updated regularly. To ensure that you have the most Approximately 15 minutes after mixing. Application time is dependent on recent version, please visit our website at the following address: www.king-masonry.com temperature. Higher temperature will require a faster application than with cooler temperatures. This product is designed to meet the performance specifications outlined in this product data sheet. If the product is used in conditions for which it was not intended, or applied in a manner COMPRESSIVE STRENGTH contrary to the written recommendations contained in the product data sheet, the product may ASTM C 109 not reach such performance specifications. The foregoing is in lieu of any other warranties, 1 day 20 MPa (2900 psi) representations or conditions, expressed or implied, including, but not limited to, implied 7 day 30 MPa (4360 psi) warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. 28 day 40 MPa (5800 psi) V1014 MIXING RATIO The mixing ratio is approximately 5 parts powder to 1 part water by volume.

FINISHING TIME Approximately 1 hour after mixing. Finishing time will depend on temperature of substrate, humidity and type of finish desired.

PACKAGING One plastic pail contains 20 kg (44 lb).

SHELF LIFE 1 year in original, unopened pail.

SURFACE PREPARATION Remove all impurities, dirt, grease, and other bond inhibiting materials from the surface. Preparation work should be done using manual or power tools cutting techniques. Dampen surface to be repaired with clean water.

MIXING The mixing ratio is approximately 5 parts powder to 1 part water. Use a clean container. Pour water into a mixing container. The mixing may be done by hand or using a slow speed drill (300 rpm-450 rpm) with a mixing paddle. The mortar should be the consistency of damp sand. Do not add too much water. Do not over mix. Working time is approximately 15 minutes.

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 400 - TERRA COTTA

RECONSTEC 400 - TERRA COTTA

KING PACKAGED MATERIALS COMPANY

RECONSTEC 500 - MARBLE AND TRAVERTINE

Marble and Travertine restoration mortar. MIXING The mixing ratio is approximately 5 parts powder to 1 part water. Use a clean DESCRIPTION container. Pour water into mixing container. The mixing may be done by hand Reconstec 500 is a mortar specially designed for the restoration of marble or using a slow speed drill (300 rpm-450 rpm) with a mixing paddle. The and travertine. Non-shrink with a very good bond to marble and travertine. mortar should be the consistency of damp sand. Do not add too much water. Easily applied to clean, sound substrates. May be feather edged. Contains Do not over mix. Working time is approximately 15 minutes. no synthetic polymers. APPLICATION & FINISHING ADVANTAGES Mortar must be scrubbed into substrate, filling all pores and voids. Use a • The same coefficient of thermal expansion as marble and travertine. steel trowel. Force material against edge of repair, working toward the center. • Very good adhesion to substrates. When the mortar is the consistency of dry sand, screed to desired finish. • Not a vapor barrier, completely breathable. • Good freeze-thaw resistance. CURING • Easy to use. Curing is not necessary. • No curing required. • Pigmented versions available. CLEAN UP Remove the mortar from tools and mixing equipment with water. Cured TECHNICAL DATA material can only be removed mechanically. Application time: Approximately 15 minutes after mixing. Application time is dependent on CAUTION temperature. Higher temperature will require a faster application than with Avoid eyes contact and prolonged contact with skin. May cause irritation to cooler temperatures. sensitive skin. In case of skin or eye contact, wash thoroughly with water. Avoid breathing the dust. In case of contact with the eyes, consult a doctor. COMPRESSIVE STRENGTH KEEP OUT OF REACH OF CHILDREN. ASTM C 109 1 day 15 MPa (2180 psi) Note: The contents of this data sheet are updated regularly. To ensure that you have the most 7 day 30 MPa (4360 psi) recent version, please visit our website at the following address: www.king-masonry.com 28 day 35 MPa (5100 psi) This product is designed to meet the performance specifications outlined in this product data MIXING RATIO sheet. If the product is used in conditions for which it was not intended, or applied in a manner The mixing ratio is approximately 5 parts powder to 1 part water by volume. contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, FINISHING TIME representations or conditions, expressed or implied, including, but not limited to, implied Approximately 1 hour after mixing. Finishing time will depend on temperature warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. of substrate, humidity and type of finish desired. V1014 SPECIFIC GRAVITY 1.8

PACKAGING One plastic pail contains 20 kg (44 lb).

SHELF LIFE 1 year in original, unopened pail.

SURFACE PREPARATION Remove all impurities, dirt, grease, and other bond inhibiting materials from the surface. Preparation work should be done manually, or carefully with power tools. Dampen surface to be repaired with clean water.

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 500 - MARBLE AND TRAVERTINE

RECONSTEC 500 - MARBLE AND TRAVERTINE

KING PACKAGED MATERIALS COMPANY

ArcHItecturAl re PAI l concrete rePAIr r RECONSTEC 300 AC

RECONSTEC 300 AC - ARCHITECTURAL CONCRETE REPAIR MORTAR

Architectural Concrete repair mortar YIELD Approximately 12 litres (0.4 ft.³) DESCRIPTION Reconstec 300 AC is a mortar specifically designed for the restoration of SPECIFIC GRAVITY architectural concrete. Non-shrink with a very good bond to the substrates. 2.2 Easily applied to clean, sound substrates. Contains no synthetic polymers. For exposed aggregate applications over ¼ inch, it is necessary to use PACKAGING Reconstec 300 AC Anchoring Cement. One plastic pail contains 20 kg (44 lb).

ADVANTAGES SHELF LIFE • Same thermal expansion coefficient as concrete. 1 year in original, unopened pail. • Excellent bond to substrate. • Not a vapor barrier. • Good resistance to freeze/thaw cycles. SURFACE PREPARATION • Easy to use. Remove all loose material, dirt, grease and any other element that could • Available in a wide variety of colours and many types of stone and sand. prevent bonding between the support and the restoration mortar, on • Pigmented version available. a minimum thickness of 3 times the diameter of the largest stone in the mixture. Preparation and cutting of the existing concrete surface should TECHNICAL DATA be done manually or with power tools. Clean the area to be repaired with Application time: clean water and saturate the surface, taking care to remove excess water. Approximately 15 minutes after mixing. Several factors, including ambient If aggregate in the mixture is ¼ inch or larger, use Reconstec 300 AC temperature, may affect application time. Anchoring Cement. Refer to the product Technical Data Sheet. It is important to use an anchoring cement that has the same color as the COMPRESSIVE STRENGTH Reconstec 300 AC used on the project. ASTM C 109 1 day 15 MPa (2180 psi) MIXING 7 day 30 MPa (4360 psi) Begin by pouring 75% of the required water into a clean container. Mixing 28 day 40 MPa (5800 psi) can be done by hand or using a slow-speed mixer (300 rpm-450 rpm) with a Jiffler-type end bit. Mix to a uniform consistency for a minimum of 3 minutes. FLEXURAL STRENGTH Add more water to adjust the mixture and obtain desired consistency. Do ASTM C 348 10.9 MPa (1581 psi) not add too much water. Do not over mix. Working time is approximately 15 minutes. MODULUS OF ELASTICITY ASTM C 469 13.8 to 16.5 GPa APPLICATION & FINISHING (2000000 to 2400000 psi) Trowel application: The mortar must be pressed against the substrate to fill all the pores and the BOND STRENGTH voids. Use a steel trowel. Working from the center, press the mortar outwards ASTM C 882 (MODIFIED) to the area to be repaired. Allow the necessary time for the mortar to achieve 11.5 MPa (1670 psi) its initial setting time. Then, using a brush or a sprayer, apply Reconstec 300 AC Vapor Retarder. Depending on the desired effect, let vapor retarder LINEAR COEFF. OF THERMAL EXPANSION soak for a period of time. Then, using a brush and water where needed, free 3.6 to 4.6 x 10-6/°C aggregates from material surface using a brushing motion. Apply desired finish. LENGTH CHANGE ASTM C 157 0.005 to 0.010 % (28 day) Use of a mold: When a mold is required, apply the Retarder inside the mold prior to casting MIXING RATIO the mixture. When the mortar has hardened enough to permit stripping, the The mixing ratio is approximately 5 parts powder to 1 part water by volume. cement paste on the surface can be removed either with a brush, a high pressure water jet or a combination of both. The desired appearance of the FINISHING TIME finished product can be achieved by exposing the aggregate, by removal of Approximately 15 minutes after mixing. Several factors, including the the concrete paste. ambient temperature, relative humidity and the type of finish desired, may influence the finishing time. CURING Curing is not mandatory.

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 300 AC

RECONSTEC 300 AC - ARCHITECTURAL CONCRETE REPAIR MORTAR

CLEAN UP Use water to remove the mortar from tools and mixing equipment. The cured product can only be removed mechanically.

CAUTION Avoid eyes contact and prolonged contact with skin. May cause irritation to sensitive skin. In case of skin or eye contact, wash thoroughly with water. Avoid breathing the dust. In case of contact with the eyes, consult a doctor. KEEP OUT OF REACH OF CHILDREN.

GUARANTEE All information provided is correct to the best of our knowledge and the product is satisfactory for the purposes for which it is intended. However, no guarantee, express or implied, is given because the mixing and application conditions are beyond our control. Our responsibility is limited specifically and only to the replacement of defective products or, if we so choose, to the refund of the cost of this product.

Note: The contents of this data sheet are updated regularly. To ensure that you have the most recent version, please visit our website at the following address: www.king-masonry.com

KING PACKAGED MATERIALS COMPANY

RECONSTEC 350 AC - RESTORATION MORTAR FOR ARCHITECTURAL CONCRETE

Architectural Concrete repair mortar YIELD Approximately 12 litres (0.4 ft.³) DESCRIPTION Reconstec 350 AC is a mortar specifically designed for the restoration of SPECIFIC GRAVITY architectural concrete. Non-shrink with a very good bond to the substrates. 2.2 Easily applied to clean, sound substrates. Contains no synthetic polymers. For exposed aggregate applications over ¼ inch, it is necessary to use PACKAGING Reconstec 350 AC Anchoring Cement. One plastic pail contains 20 kg (44 lb.)

ADVANTAGES SHELF LIFE • Same thermal expansion coefficient as concrete. 1 year in original, unopened pail. • Excellent bond to substrate. • Not a vapor barrier. • Good resistance to freeze/thaw cycles. SURFACE PREPARATION • Easy to use. Remove all loose material, dirt, grease and any other element that could • Available in a wide variety of colours and many types of stone and sand. prevent bonding between the support and the restoration mortar, on • Pigmented version available. a minimum thickness of 3 times the diameter of the largest stone in the mixture. Preparation and cutting of the existing concrete surface should be TECHNICAL DATA done manually or with power tools. Clean the area to be repaired with clean Application time: water and saturate the surface, taking care to remove excess water. Approximately 1 hour after mixing. Several factors, including ambient temperature, may affect application time. If aggregate in the mixture is ¼ inch or larger, use Reconstec 350 AC Anchoring Cement. Refer to the product Technical Data Sheet. It is COMPRESSIVE STRENGTH important to use an anchoring cement that has the same color as the ASTM C 109 Reconstec 350 AC used on the project. 1 day 15 MPa (2180 psi) 7 days 30 MPa (4360 psi) MIXING 28 days 40 MPa (5800 psi) Begin by pouring 75% of the required water into a clean container. Mixing can be done by hand or using a slow-speed mixer (300 rpm-450 rpm) with a FLEXURAL STRENGTH Jiffler-type end bit. Mix to a uniform consistency for a minimum of 3 minutes. ASTM C 348 10.9 MPa (1581 psi) Add more water to adjust the mixture and obtain desired consistency. Do not add too much water. Do not over mix. Working time is approximately 1 hour. ELASTICITY MODULUS ASTM C 469 13.8 to 16.5 GPa APPLICATION & FINISHING (2000000 to 2400000 psi) Trowel application The mortar must be pressed against the substrate to fill all the pores and the BOND STRENGTH voids. Use a steel trowel. Working from the center, press the mortar outwards ASTM C 882 (MODIFIED) to the area to be repaired. Allow the necessary time for the mortar to achieve 11.5 MPa (1670 psi) its initial setting time. Then, using a brush or a sprayer, apply Reconstec 350 AC Vapor Retarder. Depending on the desired effect, let vapor retarder soak LINEAR COEFF. OF THERMAL EXPANSION for a period of 1 to 2 hours or 15 to 20 minutes. Then, using a brush and 3.6 to 4.6 x 10-6/°C water where needed, free aggregates from material surface using a brushing motion. Apply desired finish. VOLUME CHANGE ASTM C 157 0.005 to 0.010% (28 days) Use of a mold When a mold is required, apply the Retarder inside the mold prior to casting MIXING RATIO the mixture. When the mortar has hardened enough to permit stripping, the Approximately 5 parts powder to 1 part water by volume. cement paste on the surface can be removed either with a brush, a high pressure water jet or a combination of both. The desired appearance of the FINISHING TIME finished product can be achieved by exposing the aggregate, by removal of Approximately 1 hour after mixing. Several factors, including the ambient the concrete paste. temperature, relative humidity and the type of finish desired, may influence the finishing time.

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 350 AC

RECONSTEC 350 AC - RESTORATION MORTAR FOR ARCHITECTURAL CONCRETE

CURING Moist curing should begin immediately after finishing. Use a mist spray or damp tarp for a period of two days. Protect the freshly applied mortar from direct sunlight, wind, rain and frost.

CLEAN UP Use water to remove the mortar from tools and mixing equipment. The cured product can only be removed mechanically.

Note: The contents of this data sheet are updated regularly. To ensure that you have the most recent version, please visit our website at the following address: www.king-masonry.com

KING PACKAGED MATERIALS COMPANY

ANCHORING CEMENT 300 AC

DESCRIPTION SURFACE PREPARATION Anchoring Cement 300 AC is a mortar specifically designed to improve the For surface preparation, please refer to the Reconstec 300 AC Technical Data bond to Reconstec 300 AC when the material contains aggregate that is Sheet. Before applying Anchoring Cement 300 AC, clean the section to be ¼ inch or greater. It consists of a mixture of cement, additives and sand. repaired with clean water and saturate the surface, taking care to remove Easily applied to a clean, sound substrate. Contains no synthetic polymer. excess water.

ADVANTAGES MIXING • Same thermal expansion coefficient as Reconstec 300 AC. Begin by pouring 75% of the required water into a clean container. Mixing • Excellent bonding to substrate. can be done by hand or using a slow-speed mixer (300-450 rpm) with a • Not a vapour barrier. Jiffler-type end bit. Mix to a uniform consistency. Add more water to adjust • Good resistance to freeze/thaw cycles. the mixture and obtain the desired consistency. Do not add too much water. • Easy to use. Do not over mix. Working time is approximately 1 hour. • Pigmented version available. APPLICATION & FINISHING TECHNICAL DATA The mortar must be pressed against the substrate to fill all the pores and the Application time: voids. Use a steel trowel. Force the mortar against the edge of the section to Approximately 15 minutes after mixing. Several factors, including ambient be repaired, working towards the center. The application thickness depends temperature, may affect application time. on the diameter of the largest stone in the Reconstec 300 AC mixture specific to your project. A minimum application thickness of ¼ inch is required. COMPRESSIVE STRENGTH ASTM C 109 CURING 1 day 15 MPa (2180 psi) Moisture curing should begin immediately after finishing. Use a mist spray or 7 days 30 MPa (4360 psi) damp tarp for a period of two days. Protect the freshly applied mortar from 28 days 40 MPa (5800 psi) direct sunlight, wind, rain and frost.

FLEXURAL STRENGTH CLEAN UP ASTM C 348 10.9 MPa (1581 psi) Use water to remove the mortar from tools and mixing equipment. The cured product can only be removed mechanically. ELASTICITY MODULUS ASTM C 469 13.8 to 16.5 GPa CAUTION (2000000 to 2400000 psi) Avoid contact with the eyes and prolonged contact with the skin. May irritate sensitive skin. In case the skin or eyes are splashed, rinse carefully with BOND STRENGTH water. Avoid breathing the dust. In case of contact with the eyes, consult a ASTM C 882 (MODIFIED) doctor. KEEP OUT OF REACH OF CHILDREN. 11.5 MPa (1670 psi) GUARANTEE LINEAR COEFF. OF THERMAL EXPANSION All information provided is correct to the best of our knowledge and the 3.6 to 4.6 x 10-6/°C product is satisfactory for the purposes for which it is intended. However, no guarantee, express or implied, is given because the mixing and application VOLUME CHANGE conditions are beyond our control. Our responsibility is limited specifically ASTM C 157 0.005 to 0.010% (28 days) and only to the replacement of defective products or, if we so choose, to the refund of the cost of this product. MIXING RATIO Approximately 7 parts powder to 1 part water by volume. Note: The contents of this data sheet are updated regularly. To ensure that you have the most recent version, please visit our website at the following address: www.king-masonry.com PACKAGING Plastic pail. This product is designed to meet the performance specifications outlined in this product data sheet. If the product is used in conditions for which it was not intended, or applied in a manner SHELF LIFE contrary to the written recommendations contained in the product data sheet, the product may 1 year in original, unopened pail. not reach such performance specifications. The foregoing is in lieu of any other warranties, representations or conditions, expressed or implied, including, but not limited to, implied warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. V1014

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 300 AC

ANCHORING CEMENT 300 AC

KING PACKAGED MATERIALS COMPANY

ANCHORING CEMENT 350 AC

DESCRIPTION SURFACE PREPARATION Anchoring Cement 350 AC is a mortar specifically designed to improve the For surface preparation, please refer to the Reconstec 350 AC Technical Data bond to Reconstec 350 AC when the material contains aggregate that is Sheet. Before applying Anchoring Cement 350 AC, clean the section to be ¼ inch or greater. It consists of a mixture of cement, additives and sand. repaired with clean water and saturate the surface, taking care to remove Easily applied to a clean, sound substrate. Contains no synthetic polymer. excess water.

ADVANTAGES MIXING • Same thermal expansion coefficient as Reconstec 350 AC. Begin by pouring 75% of the required water into a clean container. Mixing • Excellent bonding to substrate. can be done by hand or using a slow-speed mixer (300-450 rpm) with a • Not a vapour barrier. Jiffler-type end bit. Mix to a uniform consistency. Add more water to adjust • Good resistance to freeze/thaw cycles. the mixture and obtain the desired consistency. Do not add too much water. • Easy to use. Do not over mix. Working time is approximately 1 hour. • Pigmented version available. APPLICATION & FINISHING TECHNICAL DATA The mortar must be pressed against the substrate to fill all the pores and the Application time: voids. Use a steel trowel. Force the mortar against the edge of the section to Approximately 1 hour after mixing. Several factors, including ambient be repaired, working towards the center. The application thickness depends temperature, may affect application time. on the diameter of the largest stone in the Reconstec 350 AC mixture specific to your project. A minimum application thickness of ¼ inch is required. COMPRESSIVE STRENGTH ASTM C 109 CURING 1 day 15 MPa (2180 psi) Moisture curing should begin immediately after finishing. Use a mist spray or 7 days 30 MPa (4360 psi) damp tarp for a period of two days. Protect the freshly applied mortar from 28 days 40 MPa (5800 psi) direct sunlight, wind, rain and frost.

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC 350 AC

ANCHORING CEMENT 350 AC

KING PACKAGED MATERIALS COMPANY

RECONSTEC MF

Reconstec MF is a blended mortar, specially developed for use over masonry SAFETY PROCEDURES joints that require maximum flexibility. This mortar is made of polyurethane, Reconstec MF is made from polyurethane. Review MSDS sheets for high-grade sand, and carefully selected additives. It is available in grey, but recommended personal protective equipment before handling. Material can also be blended with a variety of coloring agents. The surface finish of Safety Data Sheets are available upon request. Reconstec MF is polished. Note: The contents of this data sheet are updated regularly. To ensure that you have the most FEATURES AND BENEFITS recent version, please visit our website at the following address: www.king-masonry.com • High bond strength. • Maximum flexibility. This product is designed to meet the performance specifications outlined in this product data • Superior workability. sheet. If the product is used in conditions for which it was not intended, or applied in a manner • Excellent resistance to de-icing salts. contrary to the written recommendations contained in the product data sheet, the product may not reach such performance specifications. The foregoing is in lieu of any other warranties, USES representations or conditions, expressed or implied, including, but not limited to, implied • Developed for use in areas where small movements occur and where warranties or conditions of merchantable quality or fitness for particular purposes, and those arising by statute or otherwise in law or from a course of dealing or usage of trade. regular mortar is subject to cracking. • Ideal for church squares. V1014 • Can be used in control joints. • Achieves high bond strength with indoor or outdoor applications.

PROCEDURES In a sufficiently large container, mix part A and part B for 3 minutes. For optimal bond strength, it is recommended to use the entire contents of part A and B. Do not mix a greater quantity than that which can be applied within 15 minutes. Tools should be thoroughly cleaned immediately after use.

With the use of a trowel, apply the mortar while applying sufficient pressure to ensure a good bond. It is recommended to start the application from the centre of the joint working towards the sides. To counteract the polished finish of the mortar, a dusting of sand can be added to the surface of the mortar joint to control the stickiness of the surface.

No curing is necessary.

OPTIMUM PERFORMANCE • Do not use Reconstec MF as a mortar bed to lay bricks or conventional stones. • Do not use this mortar at temperatures less than 4°C (40°F) or more than 38°C (95°F), or in situations where the temperature may exceed the limitations for 72 hours following the application. • Do not add any additives in the attempt to modify plastic or hardened mortar properties.

YIELD A trowel of Reconstec MF should yield enough mortar for approximately 1.5 linear meters (5 ft) of a 10 mm (3/8 inch) by 10 mm (3/8 inch) joint.

STORAGE AND SHELF LIFE Unopened contents have a minimum shelf life of 1 month if stored in a dry covered area protected from the elements.

KING PACKAGED MATERIALS COMPANY Mixing Strength 1 800 461-0566 • [email protected] • www.king-masonry.com With Satisfaction RECONSTEC MF

RECONSTEC MF

KING PACKAGED MATERIALS COMPANY