4-2 Gauges and Dimensional Standards (Pg. 1036-1055).Pdf

Gauges and dimensional standards \ Gauge blocks

Gauge blocks

The parallel gauge blocks according to DIN EN ISO 3650 will be produced in various tolerance classes that can roughly be assigned to the following application groups:

Reference normal gauge blocks are predominantly used for gauge block tests with gauge block Calibration class K testers in the calibration laboratory, together with a DKD calibration certiﬁ cate.

Workshop and normal gauge in calibration laboratory or in air conditioned measuring room for Tolerance class 0 setting or calibration of gauges as well as measuring instruments.

Most o en used working standard for checking gauges and adjusting measuring instruments. Tolerance class 1 Used in measuring rooms and on production test stations.

Gauge blocks of this class are mostly used as a normal gauge on test stations in production Tolerance class 2 areas, for setting and calibrating measuring devices as well as for setting and testing tools, appliances and machines.

Tolerance class 0 Tolerance class 1 Tolerance class 2 Limit allowances Tolerance for Limit allowances Tolerance for Limit allowances Tolerance for for length from the deviation for length from the deviation for length from the deviation Nominal measuring the nominal span the nominal span the nominal span range dimensions at dimensions at dimensions at any point any point any point ± te tv ± te tv ± te tv in mm µm µm µm µm µm µm Above Until – 10 0.12 0.10 0.20 0.16 0.45 0,30 10 25 0.14 0.10 0.30 0.16 0.60 0,30 25 50 0.20 0.10 0.40 0.18 0.80 0,30 50 75 0.25 0.12 0.50 0.18 1.00 0,35 75 100 0.30 0.12 0.60 0.20 1.20 0,35 100 150 0.40 0.14 0.80 0.20 1.60 0,40 150 200 0.50 0.16 1.00 0.25 2.00 0,40 200 250 0.60 0.16 1.20 0.25 2.40 0,45 250 300 0.70 0.18 1.40 0.25 2.80 0,50 300 400 0.90 0.20 1.80 0.30 3.60 0,50 400 500 1.10 0.25 2.20 0.35 4.40 0,60 500 600 1.30 0.25 2.60 0.40 5.00 0,70 600 700 1.50 0.30 3.00 0.45 6.00 0,70 700 800 1.70 0.30 3.40 0.50 6.50 0,80 800 900 1.90 0.35 3.80 0.50 7.50 0,90 900 1000 2.00 0.40 4.20 0.60 8.00 1,00 Property Ceramic Cemented carbide steel Length extension coeﬃ cient approx. 9.5 x 10 E-6/C 4.23 x 10 E-6/C 11.5 x 10 E-6/C Thermal conductivity Very low Low High Wear resistance Excellent Good Less good Thrust properties Acceptable Excellent Excellent Geometric accuracy Excellent Excellent Acceptable if treated correctly Corrosion resistance Excellent Good Less good Mechanical strength Good Good Very good Steel gauge block sets ( ISO 3650 )

No. 32082

Tolerance class 0 1 Number of pieces in assortment/set (PCS) Nominal dimension in assortment Material 1.005 mm, 1.01-1.20 mm, increasing by 0.01 mm, 1.3-1.9 Ident. No. 32082... 47 mm, increasing by 0.1 mm, 10-100 mm, increasing by 10 Gauge steel 006 010 mm, 1-9 mm, increasing by 1 mm Set price, € ● ● 0.5-9.5 mm, increasing by 0.5 mm, 1.001-1.009 mm, Ident. No. 32086... 87 increasing by 0.001 mm, 1.01-1.49 mm, increasing by 0.01 Gauge steel 006 010 mm, 10-100 mm, increasing by 10 mm Set price, € ○ ○ 103 1.005 mm, 1.01-1.49 mm, increasing by 0.01 mm, 0.5-24.5 Gauge steel Ident. No. 006 011 32087... mm, increasing by 0.5 mm, 25-100 mm, increasing by 25 mm Set price, € ○ ○

Prod. Gr. 3DD

Source: Hahn+Kolb Werkzeuge GmbH 1036Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1035_EN_2018_KERN[21850349]-q.indd 1036 12/17/2018 3:34:55 PM Gauges and dimensional standards \ Gauge blocks

Gauge block sets made of ceramic and cemented carbide ( ISO 3650 )

Application: . Corrosion-resistant For testing and calibrating measuring instruments . Non-magnetic and test equipment. . Very low maintenance . No. 32103–32104: Execution: . Up to 20x longer service life than steel . Gauge blocks are marked with an identiﬁ cation . Very low thermal expansion number Delivery: Advantage: in high-quality wooden case, with traceable factory . No. 32072–32073: calibration certiﬁ cate from an approved test labora- . Up to 10x longer service life than steel tory (DAkkS on request)

No. 32072 Tolerance class 0 1 Number of pieces in assortment/set (PCS) Nominal dimension in assortment Material 1.005 mm, 1.01-1.20 mm, increasing by 0.01 mm, 1.3- Ident. No. 32072... 47 1.9 mm, increasing by 0.1 mm, 10-100 mm, increasing Ceramic 006 010 by 10 mm, 1-9 mm, increasing by 1 mm Set price, € ○ ○ 0.5-9.5 mm, increasing by 0.5 mm, 1.001-1.009 mm, Ident. No. 32073... 87 increasing by 0.001 mm, 1.01-1.49 mm, increasing by Ceramic 006 010 0.01 mm, 10-100 mm, increasing by 10 mm Set price, € ● ○ 1.005 mm, 1.01-1.20 mm, increasing by 0.01 mm, 1.3- Ident. No. 32103... 47 1.9 mm, increasing by 0.1 mm, 10-100 mm, increasing Tungsten Carbide 006 010 by 10 mm, 1-9 mm, increasing by 1 mm Set price, € ○ ● 0.5-9.5 mm, increasing by 0.5 mm, 1.001-1.009 mm, Ident. No. 32104... 87 increasing by 0.001 mm, 1.01-1.49 mm, increasing by Tungsten Carbide 006 010 0.01 mm, 10-100 mm, increasing by 10 mm Set price, € ○ ○ Prod. Gr. 3DD Steel gauge block sets ( ISO 3650 )

Application: . Hardened For testing and calibrating measuring instruments . Hand-lapped and test equipment. . Gauge blocks are marked with an identiﬁ cation number Execution: . Made from high-quality, aged special steel Delivery: In wooden case

No. 32052–32053

Number of pieces in assortment/set (PCS) 32 47 87 103 1.005 mm, 1.01-1.09 mm, in- 1.005 mm, 1.01-1.20 mm, in- 0.5-9.5 mm, increasing by 0.5 creasing by 0.01 mm, 1.1-1.9 mm, creasing by 0.01 mm, 1.3-1.9 mm, mm, 1.001-1.009 mm, increasing 1.005 mm, 1.01-1.49 mm, Nominal dimension in increasing by 0.01 mm, 0.5-24.5 assortment increasing by 0.1 mm, 1-9 mm, increasing by 0.1 mm, 10-100 by 0.001 mm, 1.01-1.49 mm, increasing by 1 mm, 10-30 mm, mm, increasing by 10 mm, 1-9 increasing by 0.01 mm, 10-100 mm, increasing by 0.5 mm, 25-100 increasing by 10 mm, 50 mm mm, increasing by 1 mm mm, increasing by 10 mm mm, increasing by 25 mm Material Gauge steel Gauge steel Gauge steel Gauge steel Tolerance class 32050... 32051... 32052... 32053... Ident. No. Ident. No. Ident. No. Ident. No. 0 006 ● 006 ● 006 ● 006 ○ 1 010 ● 010 ● 010 ● 010 ● 2 020 ● 020 ● 020 ● 020 ● Set price, € Prod. Gr. 321

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1037 Availability subject to country specific rules and regulations.

1035_EN_2018_KERN[21850349]-q.indd 1037 12/17/2018 3:34:57 PM Gauges and dimensional standards \ Gauge blocks

Steel gauge block sets ( ISO 3650 ) Long version

Application: . Hand-lapped For testing and calibrating measuring instruments . Gauge blocks are marked with an identiﬁ cation and test equipment. number Execution: Delivery: . Made from high-quality, aged special steel in high-quality wooden case, with factory calibration . Hardened certiﬁ cate (DAkkS on request) Tolerance class 1 Number of pieces Nominal in assortment/ dimension in Material set (PCS) assortment 125 mm, 150 mm, 175 mm, 200 mm, 250 8 Gauge steel Ident. No. 010 32112... mm, 300 mm, Set price, € ○ 400 mm, 500 mm Prod. Gr. 321 Steel gauge block sets ( ISO 3650 ) For calibrating and testing vernier callipers and scribers

Application: . No. 32123: For vernier callipers up to 250 mm For the specifi c testing and calibration of vernier . No. 32124: For vernier callipers up to 300 mm callipers and scribers. . No. 32125: For vernier callipers up to 500 mm Execution: . No. 32126: For vernier callipers up to 800 mm . Made from high-quality, aged special steel Advantage: . Hardened . Ideal for testing gauges and measuring instruments . Hand-lapped in test rooms . Gauge blocks are marked with an identifi cation number Delivery: in high-quality wooden case, with factory calibration . No. 32122: For vernier callipers up to 150 mm certifi cate (DAkkS on request)

Tolerance class 1 Number of pieces in assort- Nominal dimension in ment/set (PCS) assortment Material Ident. No. 3 30 mm, 41.3 mm, 131.4 mm Gauge steel 010 32122... Set price, € ● 30 mm, 41.3 mm, 131.4 Ident. No. 4 Gauge steel 010 32123... mm, 243.5 mm Set price, € ○ 5 30 mm, 41.3 mm, 131.4 Gauge steel Ident. No. 010 32124... mm, 243.5 mm, 281.2 mm Set price, € ○ 30 mm, 41.3 mm, 131.4 Ident. No. 010 32125... 6 mm, 243.5 mm, 281.2 mm, Gauge steel Set price, € 481.1 mm ○ 30 mm, 41.3 mm, 131.4 mm, 243.5 mm, 281.2 mm, Ident. No. 8 Gauge steel 010 32126... 481.1 mm, 550 mm, 700 Set price, € ○ mm Prod. Gr. 321

Source: Hahn+Kolb Werkzeuge GmbH 1038Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1035_EN_2018_KERN[21850349]-q.indd 1038 12/17/2018 3:34:57 PM Gauges and dimensional standards \ Gauge blocks

Steel gauge block sets ( ISO 3650 ) For calibrating and testing micrometers

Application: Advantage: For specifi c testing and calibration of micrometers. . Ideal for testing gauges and measuring instruments in test rooms Execution: . Made from high-quality, aged special steel Delivery: . Hardened in high-quality wooden case, with traceable factory calibration certifi cate from an approved test labora- . Hand-lapped tory (DAkkS on request) . Gauge blocks are marked with an identifi cation number Technical data: . No. 32077: For reliable testing of micrometers . Tolerance class: 1 . No. 32079: To meet the minimum micrometer requirements

Number of pieces in assort- Nominal dimension in ment/set (PCS) assortment Material 2.5 mm, 5.1 mm, 7.7 mm, 10 10.3 mm, 12.9 mm, 15 mm, Ident. No. 010 32077... 17.6 mm, 20.2 mm, 22.8 Gauge steel Set price, € ● mm, 25 mm 5.1 mm, 10.3 mm, 15 mm, Ident. No. 010 32079... 5 20.2 mm, 25 mm Gauge steel Set price, € ● Prod. Gr. 3DD Individual steel gauge blocks ( ISO 3650 )

Application: Execution: For testing and calibrating measuring instruments . Gauge blocks are marked with an identiﬁ cation and test equipment. number

Tolerance class 0 1 Tolerance class 0 1 Material Gauge steel Gauge steel Material Gauge steel Gauge steel Nominal dimension (mm) 32169... 32170... Nominal dimension (mm) 32169... 32170... Ident. No. Ident. No. Ident. No. Ident. No. 0.5 005 ● 005 ● 1.19 419 ○ 419 ○ 0.6 006 ○ 006 ○ 1.2 420 ○ 420 ● 0.7 007 ○ 007 ○ 1.21 421 ○ 421 ○ 0.8 008 ○ 008 ○ 1.22 422 ○ 422 ○ 0.9 009 ○ 009 ○ 1.23 423 ○ 423 ○ 1 010 ● 010 ● 1.24 424 ○ 424 ○ 1.0005 510 ○ 510 ○ 1.25 425 ○ 425 ● 1.001 501 ○ 501 ● 1.26 426 ○ 426 ○ 1.002 502 ○ 502 ○ 1.27 427 ○ 427 ○ 1.003 503 ○ 503 ● 1.28 428 ○ 428 ○ 1.004 504 ○ 504 ○ 1.29 429 ○ 429 ○ 1.005 505 ○ 505 ● 1.3 430 ○ 430 ● 1.006 506 ○ 506 ○ 1.31 431 ○ 431 ○ 1.007 507 ○ 507 ○ 1.32 432 ○ 432 ○ 1.008 508 ○ 508 ○ 1.33 433 ○ 433 ○ 1.009 509 ○ 509 ○ 1.34 434 ○ 434 ○ 1.01 401 ○ 401 ● 1.35 435 ○ 435 ● 1.02 402 ○ 402 ● 1.36 436 ○ 436 ○ 1.03 403 ○ 403 ● 1.37 437 ○ 437 ○ 1.04 404 ○ 404 ● 1.38 438 ○ 438 ○ 1.05 405 ○ 405 ● 1.39 439 ○ 439 ○ 1.06 406 ○ 406 ● 1.4 440 ○ 440 ● 1.07 407 ○ 407 ● 1.41 441 ○ 441 ○ 1.08 408 ○ 408 ● 1.42 442 ○ 442 ○ 1.09 409 ○ 409 ● 1.43 443 ○ 443 ○ 1.1 410 ○ 410 ● 1.44 444 ○ 444 ○ 1.11 411 ○ 411 ● 1.45 445 ○ 445 ● 1.12 412 ○ 412 ● 1.46 446 ○ 446 ○ 1.13 413 ○ 413 ● 1.47 447 ○ 447 ○ 1.14 414 ○ 414 ○ 1.48 448 ○ 448 ● 1.15 415 ○ 415 ● 1.49 449 ○ 449 ● 1.16 416 ○ 416 ○ 1.5 450 ● 450 ● 1.17 417 ○ 417 ○ 1.6 016 ○ 016 ● 1.18 418 ○ 418 ○ 1.7 017 ○ 017 ●

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1039 Availability subject to country specific rules and regulations.

1039_EN_2018_KERN[21850355]-w.indd 1039 12/17/2018 3:34:58 PM Gauges and dimensional standards \ Gauge blocks

Tolerance class 0 1 Tolerance class 0 1 Material Gauge steel Gauge steel Material Gauge steel Gauge steel Nominal dimension (mm) 32169... 32170... Nominal dimension (mm) 32169... 32170... Ident. No. Ident. No. Ident. No. Ident. No. 1.8 018 ○ 018 ● 16 160 ○ 160 ● 1.9 019 ○ 019 ● 16.5 165 ○ 165 ○ 2 020 ● 020 ● 17 170 ○ 170 ● 2.5 025 ○ 025 ● 17.5 175 ○ 175 ○ 3 030 ● 030 ● 18 180 ○ 180 ● 3.5 035 ○ 035 ● 18.5 185 ○ 185 ○ 4 040 ○ 040 ● 19 190 ○ 190 ● 4.5 045 ○ 045 ● 19.5 195 ○ 195 ○ 5 050 ● 050 ● 20 200 ● 200 ● 5.5 055 ○ 055 ● 20.5 205 ○ 205 ○ 6 060 ○ 060 ● 21 210 ○ 210 ○ 6.5 065 ○ 065 ● 21.5 215 ○ 215 ○ 7 070 ○ 070 ● 22 220 ○ 220 ○ 7.5 075 ○ 075 ● 22.5 225 ○ 225 ○ 8 080 ○ 080 ● 23 230 ○ 230 ○ 8.5 085 ○ 085 ● 23.5 235 ○ 235 ○ 9 090 ○ 090 ● 24 240 ○ 240 ○ 9.5 095 ○ 095 ○ 24.5 245 ○ 245 ○ 10 100 ● 100 ● 25 250 ○ 250 ● 10.5 105 ○ 105 ○ 30 300 ○ 300 ● 11 110 ○ 110 ● 40 400 ○ 400 ● 11.5 115 ○ 115 ○ 50 500 ● 500 ● 12 120 ○ 120 ● 60 600 ○ 600 ● 12.5 125 ○ 125 ○ 70 700 ○ 700 ● 13 130 ○ 130 ○ 75 750 ○ 750 ● 13.5 135 ○ 135 ○ 80 800 ○ 800 ● 14 140 ○ 140 ○ 90 900 ○ 900 ● 14.5 145 ○ 145 ○ 100 910 ● 910 ● 15 150 ○ 150 ● Price/unit, € 15.5 155 ○ 155 ○ Prod. Gr. 321 Individual ceramic gauge blocks ( ISO 3650 )

Application: Execution: For testing and calibrating measuring instruments . Gauge blocks are marked with an identiﬁ cation and test equipment. number

Tolerance class 0 1 Tolerance class 0 1 Material Ceramic Ceramic Material Ceramic Ceramic Nominal dimension (mm) 32178... 32179... Nominal dimension (mm) 32178... 32179... Ident. No. Ident. No. Ident. No. Ident. No. 0.5 005 ● 005 ○ 1.28 428 ○ 428 ○ 1 010 ○ 010 ● 1.29 429 ○ 429 ○ 1.0005 510 ○ 510 ○ 1.3 430 ○ 430 ○ 1.001 501 ○ 501 ○ 1.31 431 ○ 431 ○ 1.002 502 ○ 502 ○ 1.32 432 ○ 432 ○ 1.003 503 ○ 503 ○ 1.33 433 ○ 433 ○ 1.004 504 ○ 504 ○ 1.34 434 ○ 434 ○ 1.005 505 ○ 505 ○ 1.35 435 ○ 435 ○ 1.006 506 ○ 506 ○ 1.36 436 ○ 436 ○ 1.007 507 ○ 507 ○ 1.37 437 ○ 437 ○ 1.008 508 ○ 508 ○ 1.38 438 ○ 438 ○ 1.009 509 ○ 509 ○ 1.39 439 ○ 439 ○ 1.01 401 ○ 401 ○ 1.4 440 ○ 440 ○ 1.02 402 ○ 402 ○ 1.41 441 ○ 441 ○ 1.03 403 ○ 403 ○ 1.42 442 ○ 442 ○ 1.04 404 ○ 404 ○ 1.43 443 ○ 443 ○ 1.05 405 ○ 405 ○ 1.44 444 ○ 444 ○ 1.06 406 ○ 406 ○ 1.45 445 ○ 445 ○ 1.07 407 ○ 407 ○ 1.46 446 ○ 446 ○ 1.08 408 ○ 408 ○ 1.47 447 ○ 447 ○ 1.09 409 ○ 409 ○ 1.48 448 ○ 448 ○ 1.1 410 ○ 410 ○ 1.49 449 ○ 449 ○ 1.11 411 ○ 411 ○ 1.5 450 ○ 450 ○ 1.12 412 ○ 412 ○ 1.6 016 ○ 016 ○ 1.13 413 ○ 413 ○ 1.7 017 ○ 017 ○ 1.14 414 ○ 414 ○ 1.8 018 ○ 018 ○ 1.15 415 ○ 415 ○ 1.9 019 ○ 019 ○ 1.16 416 ○ 416 ○ 2 020 ● 020 ○ 1.17 417 ○ 417 ○ 2.5 025 ○ 025 ○ 1.18 418 ○ 418 ○ 3 030 ● 030 ● 1.19 419 ○ 419 ○ 3.5 035 ○ 035 ○ 1.2 420 ○ 420 ○ 4 040 ○ 040 ○ 1.21 421 ○ 421 ○ 4.5 045 ○ 045 ○ 1.22 422 ○ 422 ○ 5 050 ● 050 ○ 1.23 423 ○ 423 ○ 5.5 055 ○ 055 ○ 1.24 424 ○ 424 ○ 6 060 ○ 060 ○ 1.25 425 ○ 425 ○ 6.5 065 ○ 065 ○ 1.26 426 ○ 426 ○ 7 070 ○ 070 ○ 1.27 427 ○ 427 ○ 7.5 075 ○ 075 ○

Source: Hahn+Kolb Werkzeuge GmbH 1040Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1039_EN_2018_KERN[21850355]-w.indd 1040 12/17/2018 3:35:00 PM Gauges and dimensional standards \ Gauge blocks

Tolerance class 0 1 Tolerance class 0 1 Material Ceramic Ceramic Material Ceramic Ceramic Nominal dimension (mm) 32178... 32179... Nominal dimension (mm) 32178... 32179... Ident. No. Ident. No. Ident. No. Ident. No. 8 080 ○ 080 ○ 19 190 ○ 190 ○ 8.5 085 ○ 085 ○ 19.5 195 ○ 195 ○ 9 090 ○ 090 ○ 20 200 ● 200 ○ 9.5 095 ○ 095 ○ 20.5 205 ○ 205 ○ 10 100 ● 100 ○ 21 210 ○ 210 ○ 10.5 105 ○ 105 ○ 21.5 215 ○ 215 ○ 11 110 ○ 110 ○ 22 220 ○ 220 ○ 11.5 115 ○ 115 ○ 22.5 225 ○ 225 ○ 12 120 ○ 120 ○ 23 230 ○ 230 ○ 12.5 125 ○ 125 ○ 23.5 235 ○ 235 ○ 13 130 ○ 130 ○ 24 240 ○ 240 ○ 13.5 135 ○ 135 ○ 24.5 245 ○ 245 ○ 14 140 ○ 140 ○ 25 250 ○ 250 ○ 14.5 145 ○ 145 ○ 30 300 ○ 300 ○ 15 150 ○ 150 ○ 40 400 ○ 400 ○ 15.5 155 ○ 155 ○ 50 500 ○ 500 ○ 16 160 ○ 160 ○ 60 600 ○ 600 ○ 16.5 165 ○ 165 ○ 70 700 ○ 700 ○ 17 170 ○ 170 ○ 75 750 ○ 750 ○ 17.5 175 ○ 175 ○ 80 800 ○ 800 ○ 18 180 ○ 180 ○ 90 900 ○ 900 ○ 18.5 185 ○ 185 ○ 100 910 ○ 910 ○ Price/unit, € Prod. Gr. 322 Individual carbide gauge blocks ( ISO 3650 )

Application: Execution: For testing and calibrating measuring instruments . Gauge blocks are marked with an identiﬁ cation and test equipment. number

Tolerance class 0 1 Tolerance class 0 1 Material Tungsten Carbide Tungsten Carbide Material Tungsten Carbide Tungsten Carbide Nominal dimension (mm) 32187... 32188... Nominal dimension (mm) 32187... 32188... Ident. No. Ident. No. Ident. No. Ident. No. 0.5 005 ○ 005 ● 1.31 431 ○ 431 ○ 0.6 006 ○ 006 ○ 1.32 432 ○ 432 ○ 0.7 007 ○ 007 ○ 1.33 433 ○ 433 ○ 0.8 008 ○ 008 ○ 1.34 434 ○ 434 ○ 0.9 009 ○ 009 ○ 1.35 435 ○ 435 ○ 1 010 ● 010 ● 1.36 436 ○ 436 ○ 1.0005 510 ○ 510 ○ 1.37 437 ○ 437 ○ 1.001 501 ○ 501 ○ 1.38 438 ○ 438 ○ 1.002 502 ○ 502 ○ 1.39 439 ○ 439 ○ 1.003 503 ○ 503 ○ 1.4 440 ○ 440 ○ 1.004 504 ○ 504 ○ 1.41 441 ○ 441 ○ 1.005 505 ○ 505 ○ 1.42 442 ○ 442 ○ 1.006 506 ○ 506 ○ 1.43 443 ○ 443 ○ 1.007 507 ○ 507 ○ 1.44 444 ○ 444 ○ 1.008 508 ○ 508 ○ 1.45 445 ○ 445 ○ 1.009 509 ○ 509 ○ 1.46 446 ○ 446 ○ 1.01 401 ○ 401 ○ 1.47 447 ○ 447 ○ 1.02 402 ○ 402 ○ 1.48 448 ○ 448 ○ 1.03 403 ○ 403 ○ 1.49 449 ○ 449 ○ 1.04 404 ○ 404 ○ 1.5 450 ○ 450 ○ 1.05 405 ○ 405 ○ 1.6 016 ○ 016 ○ 1.06 406 ○ 406 ○ 1.7 017 ○ 017 ○ 1.07 407 ○ 407 ○ 1.8 018 ○ 018 ○ 1.08 408 ○ 408 ○ 1.9 019 ○ 019 ○ 1.09 409 ○ 409 ○ 2 020 ● 020 ● 1.1 410 ○ 410 ○ 2.5 025 ○ 025 ○ 1.11 411 ○ 411 ○ 3 030 ○ 030 ● 1.12 412 ○ 412 ○ 3.5 035 ○ 035 ○ 1.13 413 ○ 413 ○ 4 040 ○ 040 ○ 1.14 414 ○ 414 ○ 4.5 045 ○ 045 ○ 1.15 415 ○ 415 ○ 5 050 ● 050 ● 1.16 416 ○ 416 ○ 5.5 055 ○ 055 ○ 1.17 417 ○ 417 ○ 6 060 ○ 060 ● 1.18 418 ○ 418 ○ 6.5 065 ○ 065 ○ 1.19 419 ○ 419 ○ 7 070 ● 070 ● 1.2 420 ○ 420 ○ 75 750 ○ 750 ○ 1.21 421 ○ 421 ○ 7.5 075 ○ 075 ○ 1.22 422 ○ 422 ○ 8 080 ● 080 ● 1.23 423 ○ 423 ○ 8.5 085 ○ 085 ○ 1.24 424 ○ 424 ○ 9 090 ○ 090 ○ 1.25 425 ○ 425 ○ 9.5 095 ○ 095 ○ 1.26 426 ○ 426 ○ 10 100 ● 100 ● 1.27 427 ○ 427 ○ 10.5 105 ○ 105 ○ 1.28 428 ○ 428 ○ 11 110 ○ 110 ○ 1.29 429 ○ 429 ○ 11.5 115 ○ 115 ○ 1.3 430 ○ 430 ○ 12 120 ○ 120 ○ Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1041 Availability subject to country specific rules and regulations.

1039_EN_2018_KERN[21850355]-w.indd 1041 12/17/2018 3:35:01 PM Gauges and dimensional standards \ Gauge blocks

Application: Execution: For testing and calibrating measuring instruments . Gauge blocks are marked with an identiﬁ cation and test equipment. number Delivery: Comes in a wooden case, with a calibration certiﬁ - cate from an accredited laboratory

Tolerance class 1 0 Tolerance class 1 0 Material Gauge steel Gauge steel Material Gauge steel Gauge steel Nominal dimension (mm) 32109... 32110... Nominal dimension (mm) 32109... 32110... Ident. No. Ident. No. Ident. No. Ident. No. 125 805 ● 805 ○ 500 850 ● 850 ○ 150 815 ● 815 ○ 600 860 ○ 860 ○ 175 818 ● 818 ○ 700 870 ○ 870 ○ 200 820 ● 820 ○ 800 880 ○ 880 ○ 250 825 ● 825 ○ 900 890 ○ 890 ○ 300 830 ● 830 ○ 1000 895 ○ 895 ○ 400 840 ● 840 ○ Price/unit, € Prod. Gr. 321 Gauge block accessories set 12 pieces

Application: . Blade tips for slot diameter For the use of gauge blocks for measuring devices, . Half round measuring arm with cylindrical attach- marking instruments, etc. ment 4/10/20 mm Execution: Advantage: . Adjustable gauge block holder for measuring range . Using this set cares for and preserves gauge blocks 50/100/200 mm in . Scriber point Delivery: . Centring tip In a case . Straight edge . Base for gauge block holders Technical data: . plane measuring arms for outside measurements . Number of pieces in assortment/set: 17 PCS

4 0-100

① Measuring arm ② Gauge block holder ③ Gauge blocks ④ Base

Ident. No. 020 32281... Set price, € ● Prod. Gr. 321 Source: Hahn+Kolb Werkzeuge GmbH 1042Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1039_EN_2018_KERN[21850355]-w.indd 1042 12/17/2018 3:35:03 PM Gauges and dimensional standards \ Gauge blocks

Application examples for test pins

b a c

b a A

h1 h2

Test pins made of hardened steel Tolerance class 1 (± 0.001 mm)

Application: To determine bore intervals, bore diameters, bore angularity etc. Design: Tips for ordering: . ground and lapped 5-digit art. no. (32481) + test pin ∅ = order no. . hardened 60-64 HRC . sharp-edged at one end, milled to 30° x 0.3 D at Example: test pin ∅ 6.87 mm = order no. 32481 687 the other end Example: Test pin ∅ 10.31 mm = order no. 32481 001 . dimension descriptions over Ø 3 mm

Ø mm 10.00- 12.00- 14.00- 16.00- 0.30-0.49 0.50-0.99 1.00-2.99 3.00-5.99 6.00-9.99 11.99 13.99 15.99 18.99 19.00-20.00 Pitch/length mm 0.01/40 0.01/40 0.01/70 0.01/70 0.01/70 0.01/70 0.01/70 0.01/70 0.01/70 0.01/70 32481 ref. no. 001 002 004 006 009 ● ● ● ● ● ○ ○ ○ ○ ○ h Upon request: Wooden cases for test pins, larger diameters and intermediate dimensions in µm gradations, cemented carbide and ceramic test pins on request

Test pin holder

Application: For holding 2 test pins (e.g. no. 32481) within a tolerance ﬁ eld (e.g. can be used as a limit plug gauge).

Min./max. nominal Ø 1-1.99 mm 2-4.5 mm 4.51-6.99 mm 7-9.5 mm 9.51-12 mm Length (mm) 60 68 76 84 92 Ident. No. 010 020 030 040 050 32485... Price/unit, € ● ● ● ● ● Prod. Gr. 3DA

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1043 Availability subject to country specific rules and regulations.

1039_EN_2018_KERN[21850355]-w.indd 1043 12/17/2018 3:35:04 PM Gauges and dimensional standards \ Test pins

Test pin sets in wooden case ( DIN 2269 )

Application: . Hardened 60–64 HRC For measuring bore hole clearances, bore diameters, . Sharp-edged at one end, milled to 30° x 0.3 D at angularity of bores etc. the other end Execution: Delivery: . Ground and lapped In wooden case

Tolerance class 1 2 Number of pieces in Nominal dimension of assortment/set (PCS) measuring pins Material 41 1.00-5.00 mm, in- Gauge steel Ident. No. 001 002 32486... creasing by 0.1 mm Set price, € ○ ● Ident. No. 50 5.10-10.00 mm, in- Gauge steel 101 102 32486... creasing by 0.1 mm Set price, € ○ ○ 91 1.00-10.00 mm, in- Gauge steel Ident. No. 201 202 32486... creasing by 0.1 mm Set price, € ● ● 81 1.00-5.00 mm, in- Gauge steel Ident. No. 001 002 32487... creasing by 0.05 mm Set price, € ○ ● 5.05-10.00 mm, in- Ident. No. 100 Gauge steel 101 102 32487... creasing by 0.05 mm Set price, € ○ ● 1.00-2.00 mm, in- Ident. No. 100 Gauge steel 001 002 32488... creasing by 0.01 mm Set price, € ○ ● 100 2.01-3.00 mm, in- Gauge steel Ident. No. 101 102 32488... creasing by 0.01 mm Set price, € ○ ● 3.01-4.00 mm, in- Ident. No. 100 Gauge steel 201 202 32488... creasing by 0.01 mm Set price, € ○ ● 100 4.01-5.00 mm, in- Gauge steel Ident. No. 301 302 32488... creasing by 0.01 mm Set price, € ○ ○ Ident. No. 100 5.01-6.00 mm, in- Gauge steel 401 402 32488... creasing by 0.01 mm Set price, € ○ ● 6.01-7.00 mm, in- Ident. No. 100 Gauge steel 501 502 32488... creasing by 0.01 mm Set price, € ○ ○ 100 7.01-8.00 mm, in- Gauge steel Ident. No. 601 602 32488... creasing by 0.01 mm Set price, € ○ ○ 8.01-9.00 mm, in- Ident. No. 100 Gauge steel 701 702 32488... creasing by 0.01 mm Set price, € ○ ○ 100 9.01-10.00 mm, in- Gauge steel Ident. No. 801 802 32488... creasing by 0.01 mm Set price, € ○ ○ 1.00-10.00 mm, in- Ident. No. 901 Gauge steel 901 902 32488... creasing by 0.01 mm Set price, € ○ ○ Prod. Gr. 3DD

THE HIGHEST QUALITY PRODUCTS FOR MAXIMUM EFFICIENCY. WE HAVE WHAT IT TAKES.

For a complete range of products that meet the toughest demands, visit www.iconridge.com

Source: Hahn+Kolb Werkzeuge GmbH 1044Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1044_EN_2018_KERN[21850361]-s.indd 1044 12/17/2018 3:34:53 PM Gauges and dimensional standards \ Gauges

Tool navigator ‘Gauges’ online

The gauge navigator’s simple and clear menu can be used to defi ne your The gauge navigator can be found at www.werkzeug-navigator.de. requests more easily and clearly in just four steps. Firstly, determine what Its impressive advantages at a glance: type of gauge is right for the required application: The selection ranges . from bore gauges, snap gauges, fl at gauges and ring gauges to thread Fast access and simple operation around the clock gauges. Subsequently, sizes are determined in nominal dimension spe- . Automatic shopping cart generation and enquiries sent via the Internet to cifi cations, ISO tolerance fi elds or fi gures and details, such as coating or Hahn+Kolb material. The shopping cart will then be automatically generated and sent . Quick submission of quotations, even for special gauges directly to us. This allows quotes or enquiries, particularly for special gau- . Menu-guided selection for clear specifi cation and defi nition of gauges ges, to be dealt with very quickly. We promptly check price and delivery . Enquiry with clear and unambiguous defi nitions to avoid follow-up questions options from diff erent vendors and compile the best deal for you. and wrong deliveries

Flat glass ﬂ atness tolerance 0.125 µm

Application: Delivery: For testing the ﬂ atness of faces of measuring Incl. wooden case surfaces on metal and glass objects such as gauge blocks. Technical data: . Diameter: 45 mm Execution: . Flatness tolerance: 0.125 µm . Made from special glass Ident. No. 010 41520... Price/unit, € ● Prod. Gr. 454

Angle standards made of hardened gauge steel

Application: Delivery: For precise setting and checking of angles. Set: 15’, 30’, 1°, 2°, 3°, 4°, 5°, 10°, 15°, 20°, 25°, 30°, supplied in case. Execution: . Smallest graduation 15’ (¼°) Technical data: . manufacturer tolerance ± 30” . Number of pieces in assortment/set: 12 PCS . Length: 76.4 mm . Width: 6.35 mm

Ident. No. 020 32155... Set price, € ● Prod. Gr. 3BF Test balls made of hardened gauge steel

Application: Technical data: For testing bore holes or internal cones. . Number of pieces in assortment/set: 50 PCS . Pitch: 1 mm Delivery: Each 2 x diameter 1–25 mm, in a case.

Ident. No. 030 32155... Set price, € ● Prod. Gr. 3BD

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1045 Availability subject to country specific rules and regulations.

1044_EN_2018_KERN[21850361]-s.indd 1045 12/17/2018 3:34:57 PM Gauges and dimensional standards \ Hole gauges

Limit plug gauges made of gauge steel ( DIN 2245 ) tolerance H7

Application: Notes: For checking maximum and minimum dimensions of No. 32491: Surcharge applicable to quality class 5 boreholes. and above. Please indicate the ﬁ t for the workpiece when Illustration may be diﬀ erent Execution: ordering (e.g. G9) . Go side manufactured with wear allowance in line with DIN 7164 Tolerance class H7 A-ZC/6-13 Tolerance class H7 A-ZC/6-13 Go side material Gauge steel Gauge steel Go side material Gauge steel Gauge steel Discharge side material Gauge steel Gauge steel Discharge side material Gauge steel Gauge steel Nominal Ø (mm) 32490... 32491... Nominal Ø (mm) 32490... 32491... Ident. No. Ident. No. Ident. No. Ident. No. 1 005 ● 005 ○ 34 200 ● 200 ○ 1.5 015 ● 015 ○ 35 205 ● 205 ○ 2 025 ● 025 ○ 36 210 ● 210 ○ 2.5 035 ● 035 ○ 37 215 ● 215 ○ 3 045 ● 045 ○ 38 220 ● 220 ○ 3.5 050 ● 050 ○ 40 225 ● 225 ○ 4 055 ● 055 ○ 42 230 ● 230 ○ 4.5 060 ● 060 ○ 44 235 ● 235 ○ 5 065 ● 065 ○ 45 240 ● 240 ○ 6 070 ● 070 ○ 46 245 ○ 245 ○ 7 075 ● 075 ○ 47 250 ● 250 ○ 8 080 ● 080 ○ 48 255 ● 255 ○ 9 085 ● 085 ○ 50 260 ● 260 ○ 10 090 ● 090 ○ 52 265 ● 265 ○ 11 095 ● 095 ○ 55 270 ● 270 ○ 12 100 ● 100 ○ 58 275 ● 275 ○ 13 105 ● 105 ○ 60 280 ● 280 ○ 14 110 ● 110 ○ 62 285 ● 285 ○ 15 115 ● 115 ○ 65 290 ● 290 ○ 16 120 ● 120 ○ 68 295 ○ 295 ○ 17 125 ● 125 ○ 70 300 ● 300 ○ 18 130 ● 130 ○ 72 305 ○ 305 ○ 19 135 ● 135 ○ 75 310 ● 310 ○ 20 140 ● 140 ○ 78 315 ○ 315 ○ 21 145 ● 145 ○ 80 320 ● 320 ○ 22 150 ● 150 ○ 82 325 ○ 325 ○ 23 155 ● 155 ○ 85 330 ● 330 ○ 24 160 ● 160 ○ 88 335 ○ 335 ○ 25 165 ● 165 ○ 90 340 ● 340 ○ 26 170 ● 170 ○ 92 345 ○ 345 ○ 27 175 ● 175 ○ 95 350 ○ 350 ○ 28 180 ● 180 ○ 98 355 ○ 355 ○ 30 185 ● 185 ○ 100 360 ● 360 ○ 32 190 ● 190 ○ Price/unit, € 33 195 ○ 195 ○ Prod. Gr. 3DB Limit plug gauge with intermediate size and numerical tolerance ( DIN 2245 )

Application: Notes: For checking maximum and minimum dimensions of Please indicate the tolerance (e.g. G9) or numerical boreholes. tolerance (+/-). Surcharge applicable to quality class 5 and above. Illustration may be diﬀ erent Execution: . Go side manufactured with wear allowance in line with DIN 7164 Go side material Gauge steel Go side material Gauge steel Discharge side material Gauge steel Discharge side material Gauge steel Min./max. nominal Ø 32492... Min./max. nominal Ø 32492... Ident. No. Ident. No. 2.001-2.999 mm 010 ○ 40.001-49.999 mm 080 ○ 3.001-9.999 mm 020 ○ 50.001-59.999 mm 090 ○ 10.001-13.999 mm 030 ○ 60.001-69.999 mm 100 ○ 14.001-17.999 mm 040 ○ 70.001-79.999 mm 110 ○ 18.001-23.999 mm 050 ○ 80.001-89.999 mm 120 ○ 24.001-29.999 mm 060 ○ 90.001-99.999 mm 130 ○ 30.001-39.999 mm 070 ○ Price/unit, € Prod. Gr. 3DB

Source: Hahn+Kolb Werkzeuge GmbH 1046Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1046_EN_2018_KERN[21850364]-t.indd 1046 12/17/2018 3:34:54 PM Gauges and dimensional standards \ Hole gauges

Limit plug gauge set ( DIN 2245 ) Workpiece ﬁ t H7

Application: Delivery: For checking maximum and minimum dimensions of In a case boreholes. Technical data: Execution: . Nominal dimension in assortment: 3 mm | 4 mm | . Go side manufactured with wear allowance in line 5 mm | 6 mm | 8 mm | 10 mm | 12 mm with DIN 7164 . Tolerance class: H7 . Discharge side material: Gauge steel Advantage: . Design: One-piece . Ident. No. 020: Cemented carbide has a service life approximately 20 times longer than gauge steel Go side material Gauge steel Carbide Ident. No. 010 020 32493... Set price, € ● ● Prod. Gr. 3DB Limit plug gauges made of cemented carbide ( DIN 2245 )

Application: Advantage: For checking maximum and minimum dimensions of . Cemented carbide has a service life approximately boreholes. 20 times longer than gauge steel Execution: Notes: Illustration may be diﬀ erent . Go side manufactured with wear allowance in line Surcharge applicable to quality class 5 and above. with DIN 7164 Tolerance class A-ZC/6-13 A-ZC/6-13 H7 H7 Tolerance class A-ZC/6-13 A-ZC/6-13 H7 H7 Go side material Carbide Carbide Carbide Carbide Go side material Carbide Carbide Carbide Carbide Discharge side material Carbide Gauge steel Gauge steel Carbide Discharge side material Carbide Gauge steel Gauge steel Carbide Nominal Ø (mm) 32496... 32495... 32495... 32496... Nominal Ø (mm) 32496... 32495... 32495... 32496... Ident. No. Ident. No. Ident. No. Ident. No. Ident. No. Ident. No. Ident. No. Ident. No. 1 010 ○ ------16 160 ○ 160 ○ 660 ● 660 ○ 2 020 ○ - - 520 ○ 520 ● 17 170 ○ 170 ○ - - - - 3 030 ○ - - 530 ○ 530 ● 18 180 ○ 180 ○ 680 ● 680 ● 4 040 ○ - - 540 ○ 540 ● 19 190 ○ 190 ○ - - - - 5 050 ○ - - 550 ● 550 ● 20 200 ○ 200 ○ 700 ● 700 ○ 6 060 ○ - - 560 ● 560 ● 21 210 ○ 210 ○ - - - - 7 070 ○ 070 ○ - - - - 22 220 ○ 220 ○ - - - - 8 080 ○ 080 ○ 580 ● 580 ● 23 230 ○ 230 ○ - - - - 9 090 ○ 090 ○ 590 ○ 590 ○ 24 240 ○ 240 ○ - - - - 10 100 ○ 100 ○ 600 ● 600 ● 25 250 ○ 250 ○ 750 ● 750 ● 11 110 ○ 110 ○ - - - - 26 260 ○ 260 ○ - - - - 12 120 ○ 120 ○ 620 ● 620 ● 27 270 ○ 270 ○ - - - - 13 130 ○ 130 ○ - - - - 28 280 ○ 280 ○ - - - - 14 140 ○ 140 ○ 640 ● 640 ● 30 300 ○ 300 ○ 800 ○ 800 ○ 15 150 ○ 150 ○ 650 ● 650 ○ Price/unit, € Prod. Gr. 3DB Limit sha groove gauge ( DIN 7150 )

Application: For numerical tolerances (e.g. +/- 0.005), a sur- For checking ﬂ at ﬁ ts, e.g. of grooves. charge is applicable.

Notes: Technical data: No. 32516: When ordering, please remember to . Material: Gauge steel specify the workpiece ﬁ t or tolerance.

Tolerance class P9 A-ZC/7-13 Tolerance class P9 A-ZC/7-13 Nominal dimension (mm) 32515... 32516... Nominal dimension (mm) 32515... 32516... Ident. No. Ident. No. Ident. No. Ident. No. 3 003 ○ 003 ○ 14 014 ○ 014 ○ 4 004 ○ 004 ○ 16 016 ○ 016 ○ 5 005 ○ 005 ○ 18 018 ○ 018 ○ 6 006 ● 006 ○ 20 020 ○ 020 ○ 8 008 ● 008 ○ 22 022 ○ 022 ○ 10 010 ● 010 ○ 25 025 ○ 025 ○ 12 012 ○ 012 ○ Price/unit, € Prod. Gr. 3DB

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1047 Availability subject to country specific rules and regulations.

1046_EN_2018_KERN[21850364]-t.indd 1047 12/17/2018 3:34:56 PM Gauges and dimensional standards \ Hole gauges

Limited snap gauge, double-ended/single-ended ( DIN 7150 ) double-jawed

Application: Notes: For checking the maximum and minimum dimen- When ordering, please remember to specify the sions of sha s. workpiece ﬁ t or tolerance. For numerical tolerances (e.g. +/- 0.005), a sur- Execution: charge is applicable. . Go side manufactured with wear allowance . No. 32545: Double-jawed Technical data: No. 32545 . No. 32546: Single-jawed . Material: Gauge steel

No. 32546

Tolerance class a-zc / 6-13 a-zc / 6-13 Tolerance class a-zc / 6-13 a-zc / 6-13 Nominal dimension (mm) 32545... 32546... Nominal dimension (mm) 32545... 32546... Ident. No. Ident. No. Ident. No. Ident. No. 2 005 ○ 005 ○ 38 195 ○ 195 ○ 3 020 ○ 020 ○ 40 200 ○ 200 ○ 4 030 ○ 030 ○ 42 205 ○ 205 ○ 5 040 ○ 040 ○ 45 215 ○ 215 ○ 6 045 ○ 045 ○ 46 220 ○ 220 ○ 7 050 ○ 050 ○ 47 225 ○ 225 ○ 8 055 ○ 055 ○ 48 230 ○ 230 ○ 9 060 ○ 060 ○ 50 235 ○ 235 ○ 10 065 ○ 065 ○ 52 240 ○ 240 ○ 11 070 ○ 070 ○ 55 245 ○ 245 ○ 12 075 ○ 075 ○ 58 250 ○ 250 ○ 13 080 ○ 080 ○ 60 255 ○ 255 ○ 14 085 ○ 085 ○ 62 260 ○ 260 ○ 15 090 ○ 090 ○ 65 265 ○ 265 ○ 16 095 ○ 095 ○ 68 270 ○ 270 ○ 17 100 ○ 100 ○ 70 275 ○ 275 ○ 18 105 ○ 105 ○ 75 285 ○ 285 ○ 19 110 ○ 110 ○ 80 295 ○ 295 ○ 20 115 ○ 115 ○ 85 305 ○ 305 ○ 22 125 ○ 125 ○ 90 315 ○ 315 ○ 23 130 ○ 130 ○ 95 325 ○ 325 ○ 24 135 ○ 135 ○ 100 335 ○ 335 ○ 25 140 ○ 140 ○ 110 - - 340 ○ 26 145 ○ 145 ○ 125 - - 345 ○ 27 150 ○ 150 ○ 140 - - 350 ○ 28 155 ○ 155 ○ 155 - - 355 ○ 30 160 ○ 160 ○ 170 - - 360 ○ 32 165 ○ 165 ○ 185 - - 365 ○ 34 175 ○ 175 ○ 200 - - 370 ○ 35 180 ○ 180 ○ Price/unit, € 36 185 ○ 185 ○ Prod. Gr. 3DB Adjusting ring ( DIN 2250 ) Made of hardened gauge steel

Application: . Marked with dimensions For adjusting and testing measuring instruments. Technical data: Execution: . Material: Gauge steel . Hardened

Nominal Ø (mm) 32605... Nominal Ø (mm) 32605... Ident. No. Ident. No. 2 030 ○ 12 105 ● 2.5 040 ○ 13 110 ● 3 050 ● 14 115 ● 4 060 ● 15 120 ● 5 070 ● 16 125 ● 6 075 ● 17 130 ● 7 080 ● 18 135 ● 8 085 ● 19 140 ● 9 090 ● 20 145 ● 10 095 ● 21 150 ● 11 100 ● 22 155 ●

Source: Hahn+Kolb Werkzeuge GmbH 1048Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1048_EN_2018_KERN[21850367]-o.indd 1048 12/17/2018 3:34:56 PM Gauges and dimensional standards \ Hole gauges

Nominal Ø (mm) 32605... Nominal Ø (mm) 32605... Ident. No. Ident. No. 23 160 ● 75 315 ● 24 165 ● 78 320 ○ 25 170 ● 80 325 ● 26 175 ● 82 330 ● 27 180 ● 85 335 ● 28 185 ● 88 340 ● 30 190 ● 90 345 ● 32 195 ● 92 350 ○ 33 200 ● 95 355 ● 34 205 ● 98 360 ○ 35 210 ● 100 365 ● 36 215 ● 105 370 ● 37 220 ● 110 375 ● 38 225 ● 115 380 ● 40 230 ● 120 385 ● 42 235 ● 125 390 ● 44 240 ● 130 395 ● 45 245 ● 135 400 ○ 46 250 ● 140 405 ● 47 255 ● 145 410 ○ 48 260 ● 150 415 ● 50 265 ● 155 420 ○ 52 270 ● 160 425 ● 55 275 ● 165 430 ○ 58 280 ● 170 435 ● 60 285 ● 175 440 ● 62 290 ● 180 445 ● 65 295 ● 190 455 ● 68 300 ● 200 465 ● 70 305 ● Price/unit, € 72 310 ● Prod. Gr. 3DB Setting rings with intermediate size ( DIN 2250 )

Application: . Marked with dimensions For adjusting and testing measuring instruments. Notes: Execution: When ordering, please specify the required diameter. . Hardened

Min./max. nominal Ø 32606... Min./max. nominal Ø 32606... Ident. No. Ident. No. 3.001-14.999 mm 010 ○ 50.001-59.999 mm 070 ○ 15.001-19.999 mm 020 ○ 60.001-69.999 mm 080 ○ 20.001-24.999 mm 030 ○ 70.001-79.999 mm 090 ○ 25.001-31.999 mm 040 ○ 80.001-89.999 mm 100 ○ 32.001-39.999 mm 050 ○ 90.001-99.999 mm 110 ○ 40.001-49.999 mm 060 ○ Price/unit, € Prod. Gr. 3DB Morse taper gauges

Application: Execution: No. 32635: For checking internal cones of tools and . Measuring surfaces are ground and ﬁ nely lapped workpieces. No. 32636: For testing external tapers on tools and Technical data: No. 32635 workpieces. . Tolerance class: AT4 . Material: Gauge steel

No. 32636

Morse taper Morse taper Design without tangs without tangs Taper type 32635... 32636... Ident. No. Ident. No. MK1 010 ○ 010 ○ MK2 020 ● 020 ● MK3 030 ● 030 ● MK4 040 ● 040 ● MK5 050 ● 050 ○ Price/unit, € Prod. Gr. 3DB

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1049 Availability subject to country specific rules and regulations.

1048_EN_2018_KERN[21850367]-o.indd 1049 12/17/2018 3:34:57 PM Gauges and dimensional standards \ Hole gauges

Taper gauges for steep tapers (SK)

Application: Execution: No. 32650: For testing spindle heads in line with . Measuring surfaces are ground and ﬁ nely lapped DIN 2079 and quick-release taper sha s in line with DIN 2080 Technical data: No. 32651: For testing spindle heads in line with . Tolerance class: AT4 DIN 2079 and quick-release taper shanks in line with . Material: Gauge steel No. 32650 DIN 2081.

No. 32651

Steep-angled Steep-angled Design taper taper Taper type 32650... 32651... Ident. No. Ident. No. SK30 030 ● 030 ● SK40 040 ● 040 ● SK50 050 ● 050 ● Price/unit, €

Prod. Gr. 3DB Thread gauges made of gauge steel For standard metric ISO thread

Application: No. 32675–32676: For testing the ﬂ ank and core No. 32675–32676: Up to M 1.4 = tolerance class 6h No. 32670: For testing the ﬂ ank diameter of female diameter of male threads. threads and compliance with minimum dimensions Technical data: of the external diameter. Notes: . Material: Gauge steel No. 32670: Up to M 1.4 = tolerance class 5H

No. 32670 Illustration may be diﬀ erent!

No. 32675 No. 32676

Thread limit plug Go ring gauge, 6g No-go ring Thread limit plug Go ring gauge, 6g No-go ring gauge, 6H gauge, 6g gauge, 6H gauge, 6g Thread type x nominal 32670... 32675... 32676... Thread type x nominal 32670... 32675... 32676... Ø x pitch Ident. No. Ident. No. Ident. No. Ø x pitch Ident. No. Ident. No. Ident. No. M1 x 0.25 010 ○ 010 ○ 010 ○ M8 x 1.25 080 ● 080 ● 080 ● M1.2 x 0.25 012 ● 012 ○ 012 ○ M9 x 1.25 090 ● 090 ○ 090 ○ M1.4 x 0.3 014 ● 014 ○ 014 ○ M10 x 1.5 100 ● 100 ● 100 ● M1.6 x 0.35 016 ● 016 ○ 016 ○ M11 x 1.5 110 ○ 110 ○ 110 ○ M1.7 x 0.35 017 ● 017 ○ 017 ○ M12 x 1.75 120 ● 120 ● 120 ● M1.8 x 0.35 018 ○ 018 ○ 018 ○ M14 x 2 140 ● 140 ● 140 ● M2 x 0.4 020 ● 020 ● 020 ● M16 x 2 160 ● 160 ● 160 ● M2.3 x 0.4 023 ○ 023 ○ 023 ○ M18 x 2.5 180 ● 180 ● 180 ○ M2.5 x 0.45 025 ● 025 ● 025 ○ M20 x 2.5 200 ● 200 ● 200 ● M2.6 x 0.45 026 ● 026 ○ 026 ○ M22 x 2.5 220 ● 220 ○ 220 ○ M3 x 0.5 030 ● 030 ● 030 ● M24 x 3 240 ● 240 ● 240 ● M3.5 x 0.6 035 ● 035 ● 035 ○ M27 x 3 270 ● 270 ○ 270 ○ M4 x 0.7 040 ● 040 ● 040 ● M30 x 3.5 300 ● 300 ● 300 ○ M5 x 0.8 050 ● 050 ● 050 ● M33 x 3.5 330 ○ 330 ○ 330 ○ M6 x 1 060 ● 060 ● 060 ● M36 x 4 360 ● 360 ● 360 ○ M7 x 1 070 ● 070 ● 070 ● Price/unit, € Prod. Gr. 3DB

Source: Hahn+Kolb Werkzeuge GmbH 1050Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1048_EN_2018_KERN[21850367]-o.indd 1050 12/17/2018 3:34:58 PM Gauges and dimensional standards \ Thread gauges

Thread gauges TiN-coated for standard metric ISO thread

Application: Advantage: No. 32696 Illustration may be diff erent! No. 32696: For testing the fl ank diameter of female . Improved corrosion resistance threads and compliance with minimum dimensions . Wear resistance approx. 10 times greater than of the external diameter. conventional gauge steel No. 32697: For testing the fl ank and core diameter . Extended calibration intervals of male threads. . Cost reduction Execution: . Surface hardness approx. 2500 Vickers Technical data: . Material: TiN

No. 32697

Thread limit plug Thread limit plug Go ring gauge, 6g gauge, 6H Go ring gauge, 6g gauge, 6H Thread type x nominal Ø x pitch 32696... 32697... Thread type x nominal Ø x pitch 32696... 32697... Ident. No. Ident. No. Ident. No. Ident. No. M3 x 0.5 030 ● 030 ● M12 x 1.75 120 ● 120 ● M4 x 0.7 040 ● 040 ● M14 x 2.0 140 ● 140 ● M5 x 0.8 050 ● 050 ● M16 x 2.0 160 ● 160 ○ M6 x 1.0 060 ● 060 ● M18 x 2.5 180 ○ 180 ○ M8 x 1.25 080 ● 080 ● M20 x 2.5 200 ● 200 ○ M10 x 1.5 100 ● 100 ○ Price/unit, € Prod. Gr. 325 Thread gauge sets M3–M12 for standard metric ISO thread in line with DIN 13

Execution: . Improved corrosion resistance . No. 32696: Go side with TiN coating . Wear resistance approx. 10 times greater than conventional gauge steel . No. 32696–32697: Surface hardness approx. 2500 Vickers . Extended calibration intervals . Cost reduction Advantage: . Delivery: No. 32696–32697: In wooden case

No. 32690 No. 32691–32692 No. 32696 No. 32697

Thread limit plug Thread limit plug gauges Go ring gauge gauges Go ring gauge No-go ring gauges 3 mm, 4 mm, 5 mm, 3 mm, 4 mm, 5 mm, 3 mm, 4 mm, 5 mm, 3 mm, 4 mm, 5 mm, 3 mm, 4 mm, 5 mm, Nominal dimension in assortment 6 mm, 8 mm, 10 mm, 6 mm, 8 mm, 10 mm, 6 mm, 8 mm, 10 mm, 6 mm, 8 mm, 10 mm, 6 mm, 8 mm, 10 mm, 12 mm 12 mm 12 mm 12 mm 12 mm Tolerance class 6H 6g 6H 6g 6g Material TiN TiN Gauge steel Gauge steel Gauge steel 32696... 32697... 32690... 32691... 32692... Ident. No. Ident. No. Ident. No. Ident. No. Ident. No. 400 ● 400 ● 010 ● 010 ● 010 ● Set price, €

ORION = Prod. Gr. 3DB a = Prod. Gr. 325

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1051 Availability subject to country specific rules and regulations.

1051_EN_2018_KERN[21850371]-q.indd 1051 12/17/2018 3:34:57 PM Gauges and dimensional standards \ Thread gauges

Thread gauges made of gauge steel for metric ISO ﬁ ne threads

Application: of the external diameter. Technical data: No. 32700: For testing the ﬂ ank diameter of female No. 32705–32706: For testing the ﬂ ank and core . Material: Gauge steel threads and compliance with minimum dimensions diameter of male threads.

No. 32700 Illustration may be diﬀ erent!

No. 32705 No. 32706

Thread limit plug No-go ring gauge, Thread limit plug No-go ring gauge, gauge, 6H Go ring gauge, 6g 6g gauge, 6H Go ring gauge, 6g 6g Thread type x nominal 32700... 32705... 32706... Thread type x nominal 32700... 32705... 32706... Ø x pitch Ident. No. Ident. No. Ident. No. Ø x pitch Ident. No. Ident. No. Ident. No. MF4 x 0.5 002 ● 002 ● 002 ○ MF26 x 1 089 ○ 089 ○ 089 ○ MF5 x 0.5 004 ● 004 ● 004 ● MF26 x 1.5 090 ● 090 ● 090 ● MF5 x 0.75 005 ○ 005 ○ 005 ○ MF27 x 1 094 ○ 094 ○ 094 ○ MF6 x 0.5 006 ● 006 ● 006 ○ MF27 x 1.5 095 ● 095 ● 095 ○ MF6 x 0.75 007 ● 007 ● 007 ○ MF27 x 2 096 ● 096 ○ 096 ○ MF7 x 0.75 009 ● 009 ○ 009 ○ MF28 x 1 099 ○ 099 ● 099 ○ MF8 x 0.5 010 ● 010 ● 010 ● MF28 x 1.5 100 ● 100 ● 100 ○ MF8 x 0.75 011 ● 011 ● 011 ● MF28 x 2 101 ○ 101 ○ 101 ○ MF8 x 1 012 ● 012 ● 012 ● MF30 x 1 109 ● 109 ● 109 ○ MF9 x 0.5 013 ○ 013 ○ 013 ○ MF30 x 1.5 110 ● 110 ● 110 ● MF9 x 0.75 014 ○ 014 ○ 014 ○ MF30 x 2 111 ● 111 ● 111 ○ MF9 x 1 015 ○ 015 ○ 015 ○ MF30 x 3 112 ○ 112 ○ 112 ○ MF10 x 0.5 016 ● 016 ● 016 ○ MF32 x 1.5 120 ● 120 ● 120 ○ MF10 x 0.75 017 ● 017 ● 017 ○ MF33 x 1.5 126 ○ 126 ○ 126 ○ MF10 x 1 018 ● 018 ● 018 ● MF33 x 2 127 ● 127 ○ 127 ○ MF10 x 1.25 019 ● 019 ● 019 ● MF35 x 1.5 138 ● 138 ● 138 ○ MF11 x 0.75 020 ○ 020 ○ 020 ○ MF36 x 1.5 144 ● 144 ● 144 ● MF11 x 1 021 ○ 021 ○ 021 ○ MF36 x 2 145 ● 145 ● 145 ○ MF12 x 0.5 022 ● 022 ● 022 ○ MF36 x 3 146 ○ 146 ○ 146 ○ MF12 x 0.75 023 ○ 023 ● 023 ○ MF38 x 1.5 154 ● 154 ● 154 ○ MF12 x 1 024 ● 024 ● 024 ● MF39 x 1.5 160 ○ 160 ○ 160 ○ MF12 x 1.5 025 ● 025 ● 025 ● MF39 x 2 161 ○ 161 ○ 161 ○ MF12 x 1.25 026 ● 026 ● 026 ● MF40 x 1.5 166 ● 166 ● 166 ○ MF13 x 0.75 027 ○ 027 ○ 027 ○ MF40 x 2 167 ○ 167 ○ 167 ○ MF13 x 1 028 ○ 028 ○ 028 ○ MF42 x 1.5 178 ● 178 ● 178 ○ MF14 x 0.75 031 ○ 031 ○ 031 ○ MF42 x 2 179 ○ 179 ● 179 ○ MF14 x 1 032 ● 032 ● 032 ● MF42 x 3 180 ○ 180 ○ 180 ○ MF14 x 1.5 033 ● 033 ● 033 ● MF45 x 1.5 197 ● 197 ● 197 ● MF14 x 1.25 034 ○ 034 ○ 034 ○ MF45 x 2 198 ○ 198 ○ 198 ○ MF15 x 0.75 035 ○ 035 ○ 035 ○ MF45 x 3 199 ○ 199 ○ 199 ○ MF15 x 1 036 ● 036 ● 036 ○ MF48 x 1.5 217 ○ 217 ● 217 ○ MF15 x 1.5 037 ○ 037 ○ 037 ○ MF48 x 2 218 ○ 218 ● 218 ○ MF16 x 0.75 039 ○ 039 ○ 039 ○ MF48 x 3 219 ○ 219 ○ 219 ○ MF16 x 1 040 ● 040 ● 040 ● MF50 x 1.5 230 ○ 230 ● 230 ○ MF16 x 1.5 041 ● 041 ● 041 ● MF50 x 2 231 ○ 231 ○ 231 ○ MF18 x 0.75 048 ○ 048 ○ 048 ○ MF52 x 1.5 242 ○ 242 ○ 242 ○ MF18 x 1 049 ● 049 ● 049 ● MF52 x 2 243 ○ 243 ○ 243 ○ MF18 x 1.5 050 ● 050 ● 050 ● MF56 x 1.5 269 ○ 269 ○ 269 ○ MF18 x 2 051 ○ 051 ○ 051 ○ MF56 x 2 270 ○ 270 ○ 270 ○ MF20 x 0.75 058 ○ 058 ○ 058 ○ MF60 x 1.5 294 ○ 294 ● 294 ○ MF20 x 1 059 ● 059 ● 059 ○ MF60 x 2 295 ○ 295 ● 295 ○ MF20 x 1.5 060 ● 060 ● 060 ● MF62 x 1.5 307 ○ 307 ○ 307 ○ MF20 x 2 061 ○ 061 ○ 061 ○ MF62 x 2 308 ○ 308 ○ 308 ○ MF22 x 1 069 ● 069 ● 069 ● MF64 x 1.5 320 ○ 320 ○ 320 ○ MF22 x 1.5 070 ● 070 ● 070 ● MF64 x 2 321 ○ 321 ○ 321 ○ MF22 x 2 071 ○ 071 ○ 071 ○ MF68 x 1.5 347 ○ 347 ○ 347 ○ MF24 x 1 079 ● 079 ● 079 ○ MF68 x 2 348 ○ 348 ○ 348 ○ MF24 x 1.5 080 ● 080 ● 080 ● MF70 x 1.5 360 ○ 360 ○ 360 ○ MF24 x 2 081 ● 081 ● 081 ○ MF70 x 2 361 ○ 361 ● 361 ○ MF25 x 1 084 ○ 084 ● 084 ○ Price/unit, € MF25 x 1.5 085 ● 085 ● 085 ○

Prod. Gr. 3DB

Source: Hahn+Kolb Werkzeuge GmbH 1052Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1051_EN_2018_KERN[21850371]-q.indd 1052 12/17/2018 3:34:58 PM Gauges and dimensional standards \ Thread gauges

Thread gauges made of gauge steel for UNC American standard threads

UNC

Application: and compliance with minimum dimensions of the For testing the ﬂ ank diameter of female threads external diameter.

Illustration may be diﬀ erent!

Thread type UNC Thread type UNC Tolerance class 2B Tolerance class 2B UNC/UNF code 32730... UNC/UNF code 32730... Ident. No. Ident. No. No. 4-40 UNC 020 ● 7/16”-14 095 ○ No. 5-40 UNC 025 ○ 1/2”-13 100 ● No. 6-32 UNC 030 ○ 9/16”-12 105 ○ No. 8-32 UNC 035 ● 5/8”-11 110 ● No. 10-24 UNC 040 ○ 3/4”-10 115 ● No. 12-24 UNC 045 ○ 7/8”-9 120 ● 1/4”-20 080 ● 1”-8 125 ○ 5/16”-18 085 ● Price/unit, € 3/8”-16 090 ● Prod. Gr. 3DB Thread gauges made of gauge steel for American UNF standard threads

UNF

Application: and compliance with minimum dimensions of the For testing the ﬂ ank diameter of female threads external diameter.

Illustration may be diﬀ erent!

Thread type UNF Thread type UNF Tolerance class 2B Tolerance class 2B UNC/UNF code 32730... UNC/UNF code 32730... Ident. No. Ident. No. No. 4-48 UNF 240 ○ 7/16”-20 315 ● No. 5-44 UNF 245 ○ 1/2”-20 320 ● No. 6-40 UNF 250 ○ 9/16”-18 325 ● No. 8-36 UNF 255 ○ 5/8”-18 330 ● No. 10-32 UNF 260 ● 3/4”-16 335 ● No. 12-28 UNF 265 ○ 7/8”-14 340 ● 1/4”-28 300 ● 1”-12 345 ○ 5/16”-24 305 ● Price/unit, € 3/8”-24 310 ●

Prod. Gr. 3DB Thread gauges made of gauge steel for tapered NPT American pipe thread

NPT

Application: No. 32740: For testing the ﬂ ank diameter of female Technical data: threads and compliance with minimum dimensions No. 32740 of the external diameter. . Material: Gauge steel . ANSI: ANSI B 1.20.1 No. 32741: For testing the ﬂ ank and core diameter . Thread type: National pipe tapered thread of male threads.

No. 32741

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1053 Availability subject to country specific rules and regulations.

1053_EN_2018_KERN[21850376]-r.indd 1053 12/17/2018 3:34:57 PM Gauges and dimensional standards \ Thread gauges

thread limit plug thread limit ring thread limit plug thread limit ring gauge gauge gauge gauge Pipe thread code 32740... 32741... Pipe thread code 32740... 32741... Ident. No. Ident. No. Ident. No. Ident. No. 1/16”-27 005 ○ 005 ○ 1 1/2”-11.5 080 ○ 080 ○ 1/8”-27 010 ● 010 ● 2”-11.5 090 ○ 090 ○ 1/4”-18 020 ● 020 ● 2 1/2”-8 100 ○ 100 ○ 3/8”-18 030 ● 030 ○ 3”-8 110 ○ 110 ○ 1/2”-14 040 ● 040 ● 3 1/2”-8 120 ○ 120 ○ 3/4”-14 050 ● 050 ● 4”-8 130 ○ 130 ○ 1”-11.5 060 ○ 060 ○ Price/unit, € 1 1/4”-11.5 070 ○ 070 ○ Prod. Gr. 3DB Thread gauges made of gauge steel (DIN 2999) for DIN 2999 R/Rp Whitworth pipe threads

RP R

Application: of male threads. No. 32745: For testing the fl ank diameter of female No. 32745 threads and compliance with minimum dimensions Technical data: Illustration may be diff erent! of the external diameter. . Material: Gauge steel No. 32746: For testing the fl ank and core diameter

No. 32746

Thread limit plug Thread limit ring Thread limit plug Thread limit ring gauge, Rp gauge R gauge, Rp gauge R Pipe thread code 32745... 32746... Pipe thread code 32745... 32746... Ident. No. Ident. No. Ident. No. Ident. No. 1/16”-28 005 ○ 005 ○ 1 1/4”-11 070 ○ 070 ○ 1/8”-28 010 ● 010 ● 1 1/2”-11 080 ○ 080 ○ 1/4”-19 020 ● 020 ○ 2”-11 090 ○ 090 ○ 3/8”-19 030 ● 030 ○ 2 1/2”-11 100 ○ 100 ○ 1/2”-14 040 ● 040 ○ 3”-11 110 ○ 110 ○ 3/4”-14 050 ● 050 ○ 4”-11 120 ○ 120 ○ 1”-11 060 ● 060 ● Price/unit, € Prod. Gr. 3DB Thread gauges made of gauge steel ( ISO 228 ) for cylindrical pipe threads G

Application: Technical data: No. 32750: For testing the ﬂ ank diameter of female threads and compliance with . Material: Gauge steel minimum dimensions of the external diameter. No. 32754–32755: For testing the ﬂ ank and core diameter of male threads.

No. 32750 Illustration may be diﬀ erent!

No. 32754 No. 32755

Thread limit plug Thread go ring Thread no-go ring gauge gauge gauge Tolerance class Medium A A Pipe thread code 32750... 32754... 32755... Ident. No. Ident. No. Ident. No. 1/8”-28 010 ● 010 ● 010 ○ 1/4”-19 015 ● 015 ● 015 ● 3/8”-19 020 ● 020 ● 020 ● 1/2”-14 025 ● 025 ● 025 ● 5/8”-14 030 ● 030 ○ 030 ○ 3/4”-14 035 ● 035 ● 035 ● 7/8”-14 040 ○ 040 ○ 040 ○ 1”-11 045 ● 045 ● 045 ● 1 1/8”-11 050 ○ 050 ○ 050 ○ 1 1/4”-11 - - 055 ● 055 ○ 1 1/2”-11 - - 065 ● 065 ○ 1 3/4”-11 - - 075 ○ 075 ○ 2”-11 - - 080 ○ 080 ○ Price/unit, € Prod. Gr. 3DB Source: Hahn+Kolb Werkzeuge GmbH 1054Technical data subject to change. www.iconridge.com Availability subject to country specific rules and regulations.

1053_EN_2018_KERN[21850376]-r.indd 1054 12/17/2018 3:34:58 PM Gauges and dimensional standards \ Thread gauges

Dial gauges

Application: . Ident. No. 030–050: Ident. No. 010–020: For measuring lengths and length diff erences, e.g. concen- . Measuring pin and clamping shank are made from durable stainless steel tricity, fl atness, positional measurements. . Coloured tolerance labels for clear detection in the adjusted tolerance fi elds Ident. No. 030–050: For measuring lengths and diff erences in length, e.g. con- . Comfortable li ing sleeve with additional dust protection function centricity, fl atness, position measurements. . Concentric mm display for larger, clearer digits

Execution: Advantage: . Ident. No. 010–020: . Ident. No. 010–020: Gauge slides with ceramic balls (low wear, not electrically . Measuring pin and clamping sha made from durable stainless steel conductive) . coloured tolerance labels for clear detection in the adjusted tolerance ﬁ elds Delivery: . Convenient li ing sleeve with additional dust protection function Ident. No. 010–020: In a case

Ident. No. 010 Ident. No. 020 Ident. No. 030 Ident. No. 040 Ident. No. 050

Measurement Length meas- travel of one uring range (mm) Outer Ø (mm) Scale value (mm) pointer revolution Shock protection (mm) Round mm Ident. No. 5 40 0.01 0.5 Yes 010 33000... display Price/unit, € ● Round mm Ident. No. 10 58 0.01 1.0 Yes 020 33000... display Price/unit, € ● Concentric mm 10 40 0.01 1.0 No Ident. No. 030 33000... display Price/unit, € ● Ident. No. Concentric mm 10 58 0.01 1.0 Yes 040 33000... display Price/unit, € ● Concentric mm 25 58 0.01 1.0 Yes Ident. No. 050 33000... display Price/unit, € ● Prod. Gr. 3AE Lightweight dial gauges with plastic housing ( DIN 878 )

Application: . Extra light so easy to handle For measuring lengths and length diff erences, e.g. . The plastic housing is highly resistant to chemical concentricity, fl atness, positional measurements. infl uences Execution: Delivery: . Measuring pin and clamping sha made from In a case durable stainless steel No. 33011

No. 33037

Measurement travel Length measuring Outer Ø (mm) Scale value (mm) of one pointer Outer ring material range (mm) revolution (mm) 3 40 0.01 0.5 Plastic Ident. No. 010 33011... Price/unit, € ● 10 58 0.01 1.0 Plastic Ident. No. 010 33037... Price/unit, € ● Prod. Gr. 3BD

Source: Hahn+Kolb Werkzeuge GmbH Technical data subject to change. www.iconridge.com 1055 Availability subject to country specific rules and regulations.

1053_EN_2018_KERN[21850376]-r.indd 1055 12/17/2018 3:35:02 PM