FARMALL® 110A –140A TIER 4 B / FINAL SPECIFICATIONS FARMALL 110A –140A TIER 4 B / FINAL TRACTOR SPECIFICATIONS Since 1923, the Farmall name has meant power, performance, durability and value. The new 110 – 140 HP feature powerful 4.5L FPT engines equipped with Selective Catalytic Reduction (SCR)-only technology that meets stringent Tier 4 B/Final emissions standards without compromising power or fuel efficiency. These workhorse tractors provide value without compromise with many no-nonsense standard features, plus factory options and dealer-installed options to create a tractor right for your operation at the right price.

MODEL FARMALL 110A FARMALL 120A FARMALL 130A FARMALL 140A GROUND SPEEDS1 – All Purpose 30 KPH POWER FORWARD - LOW - CREEPER4 ON Type Case IH FPT Tier 4 B / Final with Selective Catalytic Reduction (SCR) Gear 1 2 3 4 Engine HP at 2,200 RPM 110 120 130 140 Direct Drive2 0.17/ 0.26 / 0.36 / 0.50 / PTO HP at Rated 540 Std. / 1,000 Opt. RPM 90 96 105 115 MPH / KPH 0.28 0.43 0.58 0.80 Cylinders / Valves / Displacement 4 / 8 / 274 cu. in. (4.5 L) Under Drive3 0.13 / 0.28 / 0.28 / 0.39 / Aspiration, Turbocharged or Naturally Aspirated Turbocharged & intercooled MPH / KPH 0.21 0.45 0.45 0.62 ELECTRICAL SYSTEM REVERSE - LOW - CREEPER4 ON SPECIFICATIONS Battery, Volts / Alternator, Amps 12 volt / 120 amps Gear 1 2 3 4 TRANSMISSION / PTO Direct Drive2 0.18 / 0.30 / 0.37/ 0.52 / Standard (Base) 8F × 8R with power shuttle MPH / KPH 0.29 0.49 0.60 0.83 Optional 8F × 8R with mechanical shuttle or 16F × 8R with power shuttle and hi-lo Under Drive3 NA Creeper Speeds @ Rated Engine RPM See ground speeds chart at right MPH / KPH AXLES FORWARD - LOW - CREEPER4 OFF Rear (Standard / Optional) Flange / Bar Gear 1 2 3 4 Rear Bar Axle Diameter 3.071 in. (78 mm) Direct Drive2 1.7/ 2.6 / 3.6 / 5.0 / Front Axle (Standard / Optional) 2WD / Class 3 non-suspended standard-duty MPH / KPH 2.8 4.3 5.8 8.0 Tread Adjustability 64.0 in. – 80.0 in. (1 626 – 2 032 mm) Under Drive3 1.3 / 2.1 / 2.8 / 3.9 / Standard Wheelbase – 2WD / MFD 100.4 (2 550) / 99 (2 520) 95.7 (2 432) / 104 (2 640) MPH / KPH 2.1 3.3 4.5 6.2 HYDRAULIC SYSTEM REVERSE - LOW - CREEPER4 OFF Type Open center system, CCLS remotes Gear 1 2 3 4 Main Hydraulic Pump Type Fixed displacement Direct Drive2 1.8 / 3.0 / 3.7/ 5.2 / Implement Flow Capacity 22 GPM (83 L/min.) MPH / KPH 2.9 4.9 6.0 8.3 Number of Standard Remote Valves 2 std; 3 or 4 opt Under Drive3 NA 3-POINT HITCH MPH / KPH 3-Point Hitch Features Category II, draft sensing, adjustable FORWARD - HIGH - CREEPER4 OFF Hitch Lift Capacity 24 Inches Behind Pin 7,200 lbs. (3 266 kg) Gear 1 2 3 4 CAPACITIES Direct Drive2 6.3 / 9.8 / 13.3 / 18.4 / Fuel Tank capacity 56.8 U.S. gal. (215 L) MPH / KPH 10.2 15.7 21.3 29.6 Engine Oil with Filter 10.6 quart (10 L) 3 Under Drive 4.9 / 7.6 / 10.3 / 14.3 / Hydraulic Fluid – 2WD / 4WD 63.4 quart (60 L) / 71.8 quart (68 L) MPH / KPH 7.9 12.2 14.3 23.0 Diesel Exhaust Fluid (DEF) Tank Capacity 7.9 U.S. gal. (30 L) REVERSE - HIGH - CREEPER4 OFF HEIGHT Gear 1 2 3 4 Height to Top of Cab / ROPS Raised 110 in. (2 800 mm) / 117.3 (2 980 mm) 2 Direct Drive 6.6 / 10.1 / 13.7/ 19.0 / WIDTH MPH / KPH 10.5 16.2 22.0 30.6

Overall Width, with Standard Wheels 74.5 in. (1 893 mm) at fenders; 98 in. (2 490 mm) bar axle ends 3 Under Drive NA WEIGHT MPH / KPH Weight, 2WD w/ ROPS 9,590 lbs. (4 350 kg) preliminary 9,660 lbs. (4 382 kg) preliminary FARMALL 110A 120A 125A 140A Weight, MFD / 4WD w/ ROPS 10,065 lbs. (4 563 kg) preliminary 10,225 lbs. (4 638 kg) preliminary Rear Axle Ratio 31.714 Weight, 2WD w/ Cab 9,970 lbs. (4 522 kg) preliminary 10,040 lbs. (4 554 kg) preliminary Rear Tire Size 18.4 – 34 R1 Weight, MFD w/ Cab, without Ballast 10,445 lbs. (4 738 kg) preliminary 10,605 lbs. (4 810 kg) preliminary Rolling Radius 31.3 in. (795.0 mm) Weight (total) w/ maximum Ballast 12,500 lbs. (5 670 kg) preliminary 12,700 lbs. (5 761 kg) preliminary TIRE SIZE 1. Speeds @ 2,200 engine RPM 2. 8 × 8 Speeds Front Tire, 2WD 10.00 – 16, 8 ply, F2 3. With 16 × 8 Transmission Option Front Tire, MFD 14.9 × 24, 6 ply, R1 4. Optional Rear Tire 18.4 × 34, 8 ply, R1

Specifications are subject to change without notice. CNH Industrial America LLC reserves the right to make improvements in design and changes in specifications at any time without notice and without incurring any obligation to install them on units previously sold. Specifications, descriptions and illustrative material herein are as accurate as known at time of publication, but are subject to change without notice. Availability of some models and equipment builds varies according to the country in which the equipment is used. ©2015 CNH Industrial America LLC. All rights reserved. Case IH is a trademark registered in the United States and many other countries, owned by or licensed to CNH Industrial N.V., its subsidiaries or affiliates. CIH01151501