48IN. STEEL CORE 5-1 TIMBERJACK OWNER’S MANUAL

WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.

Item# 38589 48IN. STEEL CORE 5-1 TIMBERJACKOWNER’S MANUAL 48IN. STEEL CORE 5-1 TIMBERJACKOWNER’S MANUAL

Thank you very much for choosing a Roughneck™ Product! For future reference, please SPECIFIC OPERATION WARNINGS complete the owner’s record below: Model: ______Purchase Date: ______IMPROPER USE OF THIS MULTIFUNCTIONAL TIMBERJACK MAY Save the receipt, warranty and these instructions. It is important that you read the entire manual WARNING: RESULT IN INJURY. to become familiar with this product before you begin using it. ■ It cannot be used as a wedge or pry bar. ■ Flexing the handle in a perpendicular direction may cause handle fracture and result in This timberjack is designed for certain applications only. The distributor cannot be responsible personal injury. for issues arising from modification. We strongly recommend this timberjack is not modified ■ Be sure to tighten all nuts and bolts prior to first use and check them periodically to keep and/or used for any application other than that for which it was designed. If you have any them tight. questions relative to a particular application, DO NOT use the timberjack until you have first ■ Not for overhead lifting. contacted distributor to determine if it can or should be performed on the product.

For technical questions, please call 1-800-222-5381. INSTALLATION & OPERATION INSTRUCTIONS 1. Assemble the Bracket (2) with the Adjustable Panel (3) by Bolt (M10*60) (11), Spring Washer WARNING: Read carefully and understand all INSTRUCTIONS before operating. (M10) (14) and Nut (M10) (13) to form a bracket assembly. As shown in Figure 1. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Save these instructions in a safe place and on hand so that they can be read when required. Keep these instructions to assist in future servicing.

INTRODUCTION This timberjack is a professional quality multiuse for the serious wood cutter. Great tool for turning logs and holding them up off the ground for easier and safer cutting. 5-in-1 Multi-Functions: Log lifter; Cant ; Log holder; Timber carrier; Post remover

GENERAL SAFETY REGULATIONS

WARNING: Read and understand all instructions. Figure 1 The warnings, and instructions discussed in this instruction manual WARNING: 2. Assemble the Hook (4) with Bushing (7), Bolt (M10*75) and Locknut (M10) (12) to form a hook cannot cover all possible conditions or situations that could occur. It must be assembly. As shown in Figure 2. understood by the operator that common sense and caution are factors that cannot be built into this product, but must be supplied by the operator. • Keep the work area clean and dry. Damp or wet work areas can result in injury. • Keep children away from work area. Do not allow children to handle this product. • Always wear ANSI-approved safety glasses and heavy-duty work gloves during assembly and use. Do not wear loose clothing or jewelry, which can get caught in moving parts. • Store idle equipment. When not in use, and equipment should be stored in a dry location to inhibit rust. Always lock up tools and equipment, and keep out of reach of children. • Use the right tool for the job. Do not attempt to force small equipment to do the work of larger industrial equipment. There are certain applications for which this equipment was designed. It will do the job better and more safely at the capacity for which it was intended. Do not modify this equipment, and do not use this equipment for a purpose for which it was not intended. • Check for damaged parts. Before using this product, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that Figure 2 may affect the operation of this product. Replace damaged or worn parts immediately. • Do not overreach. Keep proper footing and balance at all times to prevent tripping, falling, back injury, etc. • DO NOT use the equipment when tired or under the influence of drugs, alcohol, or medication.A moment of inattention while operating this equipment may result in serious personal injury. • Industrial applications must follow OSHA requirements. 1 of 7 2 of 7 48IN. STEEL CORE 5-1 TIMBERJACKOWNER’S MANUAL 48IN. STEEL CORE 5-1 TIMBERJACKOWNER’S MANUAL

3. Assemble the other components based on different applications. 6. Finally, assemble the End (5) onto the bracket assembly by a Pin (9). As shown in Figure 6 and Function 1: Log lifter (Figure 3) Figure 7

Figure 3

4. Insert the Handle (1) through into the bracket assembly hole, and fasten it with Thumb Screw (M10) (15), Figure 6 Figure 7 as shown in Figure 4. Function 2: (Figure 8 & 9). Location holes

Figure 8 Figure 9 Figure 4 4. Put the Handle (1) into the bracket assembly hole, fasten the Handle (1) with Thumb Screw (M10) 5. Then, lock the hook assembly into the location hole of the bracket assembly with Pin (9). The 2 location (15). As shown in Figure 4. holes are optional according to the actual situation. As shown in Figure 5. 5. Then lock the hook assembly into the location hole of the bracket assembly by a Pin (9). The 2 location holes are optional according to actual situation. As shown in Figure 5. 6. Finally, assemble the End (5) onto the bracket assembly by a Pin (9). As shown in Figure 6 and Figure 7. Function 3: Log holder (Figure 10 & 11)

Figure 5

Figure 10 Figure 11

3 of 7 48IN. STEEL CORE 5-1 TIMBERJACKOWNER’S MANUAL 48IN. STEEL CORE 5-1 TIMBERJACKOWNER’S MANUAL

4. Assemble the End (5) onto the bracket assembly by two Pins (9). As shown in Figure 12. 4. Assemble the End (5) onto the bracket assembly with two Pins (9). As shown in Figure 15.

Location Adjustable holes Panel (3)

Figure 12 Figure 15 5. Then lock the hook assembly onto the Adjustable Panel (3) of the bracket assembly by a Pin (9), the hook assembly could be moved to appropriate location according to actual use. As shown in Figure 5. Lock the hook assembly into the location hole of the bracket assembly by a Pin (9). The 2 location 13. holes are optional according to actual situation. As shown in Figure 16.

Figure 16 6. Finally, insert the fiberglass handle through into the assembly hole on one of the Brackets (2) (the one Figure 13 without End (5)). As shown in Figure 14. 6. Finally, bind the bracket assembly on fixed object such as the trunk with the (6) and Lock (8) to Function 5: Post remover (Figure 17) support the wood. Function 4: Timber carrier (Figure 14)

Figure 14 Figure 17

4 of 7 5 of 7 48IN. STEEL CORE 5-1 TIMBERJACKOWNER’S MANUAL 48IN. STEEL CORE 5-1 TIMBERJACKOWNER’S MANUAL

4. Assemble the End (5) onto the bracket assembly by two Pins (9). As shown in Figure 12. Storage ① . After use, clean the tool with a dry and soft cloth. Store the product in a dry place with good ventilation. Do not expose it to excessive heat, humidity or sunlight. Never let it touch any corrosive substances. ② . Store it out of the reach of children.

DIAGRAMS AND PARTS LIST Adjustable 12 Panel (3) 11 8 5 6

Figure 12 15 5. Insert the Handle (1) through into the bracket assembly hole, and fasten it with Thumb Screw (M10) 7 (15), as shown in Figure 18. 13 14

1

2 15 3 11 4 10 8 9

No. Description Qty. No. Description Qty. Figure 18 1 Handle 1 9 Pin 3 2 Bracket 2 10 Bolt (M10*75) 4 6. Then lock the hook assembly to the bracket assembly by one Pin (9). As shown in Figure 19. 3 Adjustable Panel 2 11 Bolt (M10*60) 2 NOTE: The hook assembly must be locked into the second hole (the one the pin points at in 4 Hook 2 12 Locknut (M10) 4 Figure 19) of Adjustable Panel (3). 5 End 1 13 Nut (M10) 2 6 Chain 1 14 Spring Washer (M10) 2 7 Bushing 4 15 Thumb screw (M10) 2 8 Lock 2 For replacement parts and technical questions, please call 1-800-222-5381.

WARRANTY One-Year Limited Warranty

Figure 19 Distributed by MAINTAINANCE Northern Tool + Equipment Co., Inc. Transportation Burnsville, MN 55306 When the timberjack is in transit, do not expose it to direct sunlight and avoid rain, falling, NorthernTool.com corrosive substances, etc. Made in China 6 of 7 7 of 7