® PERSONAL PROTECTIVE EQUIPMENT (PPE) Komeen Some materials that are chemical-resistant to Komeen are barrier laminate, butyl rubber ≥14 mils, or nitrile rubber ≥14 mils. If you want more options, Aquatic Herbicide follow the instructions for category A on an EPA chemical-resistant category selection chart. Mixers, loaders, applicators, and other handlers must wear the following: For use in still or flowing water sites including: golf course, ornamental, • Long-sleeve shirt and long pants; fish, and fire ponds; fresh water lakes, ponds, reservoirs, fish hatcheries, • Shoes plus socks; and industrial waters to include cooling water sources and hydroelectric • Chemical-resistant gloves (such as nitrile or butyl rubber). reservoirs, crop and non-crop irrigation and drainage systems (canals, streams, ditches, and laterals), and potable water reservoirs. Follow manufacturer’s instructions for cleaning/maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep Active Ingredient and wash PPE separately from other laundry. Discard clothing and other Copper ethylenediamine complex† (CAS# 13426-91-0)...... 22.9% absorbent material that have been drenched or heavily contaminated with Other Ingredients...... 77.1% the product’s concentrate. Do not reuse them. TOTAL ...... 100.0% † Metallic copper equivalent = 8% USER SAFETY RECOMMENDATIONS Keep Out of Reach of Children Users should: • Wash the outside of gloves before removing. WARNING/AVISO • Wash hands before eating, drinking, chewing gum, using tobacco, or using the toilet. Si usted no entiende la etiqueta, busque a alguien para que se la explique a • Remove clothing/PPE immediately if pesticide gets inside. Then wash usted en detalle. (If you do not understand the label, find someone to explain it thoroughly and put on clean clothing. to you in detail.) • Remove PPE immediately after handling this product. As soon as Refer to inside of label booklet for additional precautionary information and possible, wash thoroughly and change into clean clothing. directions for use including first aid and storage and disposal. Notice: Read the entire label before using. Use only according to label ENVIRONMENTAL HAZARDS directions. Before buying or using this product, read Warranty Disclaimer This pesticide is toxic to fish and aquatic invertebrates. Waters treated with and Misuse statements inside label booklet. this product may be hazardous to aquatic organisms. Treatment of aquatic EPA Reg. No. 67690-25 FPL20171220 weeds and algae can result in oxygen loss from decomposition of dead algae Komeen is a registered trademark of SePRO Corporation. and weeds. This oxygen loss can cause fish and invertebrate suffocation. To SePRO Corporation 11550 North Meridian Street, Suite 600, Carmel, IN 46032 U.S.A. minimize this hazard, do not treat more than ½ of the water body to avoid depletion of oxygen due to decaying vegetation. Wait at least 10 to 14 days PRECAUTIONARY STATEMENTS between treatments. Begin treatment along the shore and proceed outwards Hazards to Humans and Domestic Animals in bands to allow fish to move into untreated areas. Consult with the State or local agency with primary responsibility for regulating pesticides before Keep Out of Reach of Children applying to public waters, to determine if a permit is required. Certain water conditions including low pH (<6.5), low dissolved organic WARNING/AVISO carbon (DOC) levels (3.0 mg/L or lower), and “soft” waters (i.e. alkalinity less Si usted no entiende la etiqueta, busque a alguien para que se la explique a than 50 mg/L), increase the potential acute toxicity to non-target aquatic usted en detalle. (If you do not understand the label, find someone to explain organisms. Do not use in waters containing trout or other fish species that it to you in detail.) are highly sensitive to copper if the alkalinity is less than 50 ppm. Fish toxicity generally decreases when the hardness of water increases. Komeen must not May be fatal if swallowed. May be fatal if inhaled. Do not breathe vapor be used in ornamental ponds containing Koi. or spray mist. Harmful if absorbed through skin. Causes moderate eye irritation. Avoid contact with skin, eyes or clothing. Prolonged or DIRECTIONS FOR USE frequently repeated skin contact may cause allergic reactions in some individuals. It is a violation of Federal Law to use this product in a manner inconsistent with its labeling. Read all directions for use carefully before applying this For applications in waters destined for use as drinking water, those waters product. Use only according to label directions. must receive additional and separate potable water treatment. Do not apply more than 1.0 ppm as metallic copper in any waters. Do not apply Komeen in a way that will contact workers or other persons, either directly or through drift; only protected handlers may be in close FIRST AID proximity to the mixing area or application equipment while in use. For any If • Call a poison control center or doctor immediately for treatment requirements specific to your State or Tribe, consult the State or Tribal agency swallowed advice. responsible for pesticide regulation. • Have person sip a glass of water if able to swallow. PRODUCT INFORMATION • Do not induce vomiting unless told to do so by a poison control center or doctor. Komeen controls many submersed and floating aquatic plant species • Do not give anything by mouth to an unconscious person. including hydrilla (Hydrilla verticillata), Brazilian elodea (Egeria densa), naiad If inhaled • Move person to fresh air. (Najas spp.), coontail (Ceratophyllum demersum), elodea (Elodea canadensis), • If person is not breathing, call 911 or an ambulance, then give water lettuce (Pistia stratiotes), water fern (Salvinia and Azolla spp.), artificial respiration, preferably mouth-to-mouth if possible. duckweed (Lemna and Landoltia spp.), water hyacinth (Eichhornia crassipes) • Call a poison control center or doctor for further treatment and other submersed and floating aquatic weed species that are sensitive to advice. copper. Under certain water quality conditions, such as low water hardness, Komeen may also control Eurasian watermilfoil (Myriophyllum spicatum), If on skin • Take off contaminated clothing. sago pondweed (Potamogeton pectinatus) and American pondweed or clothing • Rinse skin immediately with plenty of water for 15 - 20 minutes. (Potamogeton nodosus). • Call a poison control center or doctor for treatment advice. If in eyes • Hold eye open and rinse slowly and gently with water for Komeen can also be effective in controling various filamentous and macro 15 - 20 minutes. Remove contact lenses, if present, after the algae, such as Cladophora, Pithophora, Hydrodictyon, Chara, and Nitella, in first 5 minutes, then continue rinsing eye. the same use sites. • Call a poison control center or doctor for treatment advice. Apply when weeds are actively growing. The most copper sensitive weed Have the product container or label with you when calling a poison control species require a minimum of three (3) to twenty-four (24) hours of contact center or doctor, or going for treatment. In case of emergency endangering with Komeen in order to provide effective control. Less susceptible species health or the environment involving this product, call INFOTRAC at may require longer contact time or higher doses. Significant water movement 1-800-535-5053. may result in dilution of the treated water and reapplication may be 1 necessary. Susceptible aquatic weeds will generally drop below the surface when fish are present. In that case, do not exceed a concentration of 0.4 of the water within 3 to 14 days after treatment. If this effect is not observed, ppm during any single application and wait a minimum of 10 days between Komeen may be re-applied after a minimum of 10 to 14 days after the initial treatments. application. Once weeds drop below the surface, it can take up to 6 weeks to When treating slow-moving water, apply the spray solution counter to the realize the full effect of the treatment. flow of water. Komeen may be applied by aircraft, sprayer or spray boat as a surface spray, TABLE 1 as a subsurface application through weighted hoses, or through injection Application Concentrations For Submersed Aquatic Weed Control equipment. Komeen may be applied in combination with other aquatic Metallic Copper Level herbicides and algaecides, or mixed with adjuvants, a polymer (except Weed Species Required For Control (ppm) CA), or surfactants as appropriate. As a surface or subsurface application, † Komeen may be applied diluted or undiluted, whichever is most suitable to American pondweed (Potamogeton nodosus) 0.75 - 1.0 ensure uniform coverage of the treated area. Apply Komeen to the area where Brazilian elodea (Egeria densa) 0.50 - 1.0 the greatest concentration of target plants or algae are located, and in a Coontail (Ceratophyllum demersum) 0.50 - 1.0 manner that will deliver the herbicide to the target organism. Elodea (Elodea canadensis) 0.50 - 1.0 Eurasian watermilfoil (Myriophyllum spicatum) † 0.75 - 1.0 Dilution with water may be necessary at the lower application rates to ensure uniform coverage of the treated area. Dilute the required amount of Komeen with Hydrilla (Hydrilla verticillata) 0.75 - 1.0 enough water to ensure even distribution with the type of equipment being used. Naiad (Najas spp.) 0.50 - 1.0 Pondweed spp. (Potamogeton spp.) 0.75 - 1.0 Use Restrictions Sago pondweed (Potamogeton pectinatus) † 0.50 - 1.0 • Do not enter or allow others to enter treatment area until application is Other susceptible submersed species 0.75 - 1.0 complete. † • Do not apply Komeen directly to, or otherwise permit it to come into Control generally only in low water hardness. contact with any desirable plants as injury may result. Komeen can also be effective on many species of algae at concentrations • Do not apply in such a way that concentrated Komeen comes in contact ranging from 0.2 to 1.0 ppm metallic copper. Follow the use directions with crops, ornamentals, grass or desirable plants. described for aquatic weeds. • Wash spray equipment thoroughly before and after each application. TABLE 2 Spray Drift Management † A variety of factors including weather conditions (e.g., wind direction, wind Foliar Application Rates For Floating Aquatic Weed Control speed, temperature, relative humidity) and method of application (e.g., Weed Species ppm metallic copper ground, aerial, airblast, chemigation) can influence pesticide drift. The Duckweed (Lemna, Landoltia, and Spirodela spp.) 0.75 - 1 applicator must evaluate all factors and make appropriate adjustments when Water fern (Salvinia and Azolla spp.) 0.75 - 1 applying this product. Water hyacinth (Eichhornia crassipes) 0.75 - 1 Droplet Size Water lettuce (Pistia stratiotes) 0.5 - 0.75 † The addition of a surfactant is recommended to improve efficacy on floating Apply only as a medium or coarser spray (ASAE standard 572) or a volume plants. Follow surfactant product labeling instructions for application rates and mean diameter of 300 microns or greater for spinning atomizer nozzles. use directions. Add Komeen and appropriate surfactant to a recommended minimum of 50 gallons of spray solution per surface acre. Use an adequate Wind Speed spray volume to ensure good coverage of the plant. Do not exceed 3.34 gallons Do not apply at wind speeds greater than 15 mph. Only apply this product if of Komeen per acre foot. the wind direction favors on-target deposition (approximately 3 to 10 mph), Application Rate Calculation and there are no sensitive areas within 250 feet downwind. For large bodies of water, determine the size (in acres) and the average Temperature Inversions depth (in feet) of the area to be treated. Application rates are calculated by If applying at wind speeds less than 3 mph, the applicator must determine using the following formula to obtain the appropriate copper concentration: if a) conditions of temperature inversion exist, or b) stable atmospheric Desired concentration of copper (ppm) x Average depth of water (feet) conditions exist at or below nozzle height. Do not make applications into x 3.34 = Gallons of Komeen per surface acre areas of temperature inversions or stable atmospheric conditions. To calculate the area and average depth of a lake or pond, use the following Other State and Local Requirements formulas and conversion factors. All measurements (length, width, radius, Applicators must follow all state and local pesticide drift requirements depth) should be in feet. regarding application of copper compounds. Where states have more Formulas stringent regulations, they must be observed. • Area of a square or rectangle (ft2) = length x width Equipment • Area of a circle (ft2) = radius x radius x 3.14 All aerial and ground application equipment must be properly maintained and • Average depth (ft) = sum of all depth measurements ÷ number of calibrated using appropriate carriers or surrogates measurements (The more measurements taken, the more accurate the average depth will be.) Additional requirements for aerial applications: - The boom length must not exceed 75% of the wingspan or 90% of the Conversion Factors rotor blade diameter. • 1 gallon = 4 quarts or 8 pints or 16 cups or 128 fluid ounces • 1 quart = 2 pints or 4 cups or 32 fluid ounces - Release spray at the lowest height consistent with efficacy and flight • 1 acre = 43,560 square feet safety. Do not release spray at a height greater than 10 feet above the • 1 acre-foot = 43,560 cubic feet = 325,762 gallons = 2,720,000 pounds crop canopy unless a greater height is required for aircraft safety. - When applications are made with a crosswind, the swath must TABLE 3 be displaced downwind. The applicator must compensate for this Average Water Gallons of Komeen per Surface Acre to displacement at the up and downwind edge of the application area by Depth of Achieve the Desired Copper Concentration† adjusting the path of the aircraft upwind. Treatment Site (feet) 0.5 ppm 0.75 ppm 1.0 ppm Additional requirements for ground boom application: 1 1.7 2.5 3.3 Do not apply with a nozzle height greater than 4 feet above the water. 2 3.3 5.0 6.6 APPLICATION INFORMATION 3 5.0 7.5 10.0 4 6.7 10.0 13.3 In lakes, reservoirs, and ponds, the application site is defined by this label as the specific location where Komeen is applied. Use the lower listed rate in 5 8.4 12.5 16.7 soft water (less than 50 ppm alkalinity), for light infestations and less mature 6 10.0 15.0 20.0 plants; use the higher concentration in hard water (above 50 ppm alkalinity), 7 11.7 17.5 23.3 for dense infestations and when targeting more mature vegetation. 8 13.4 20.0 26.7 9 15.0 22.5 30.0 For aquatic weed control (including vascular plants and algae), do not exceed 1.0 ppm metallic copper during any single application; wait a minimum of 14 10 16.7 25.1 33.4 days between treatments, except for algae control in aquaculture ponds † For surface applications, dilute Komeen with water in a minimum ratio of 4:1 (Komeen:water). For subsurface applications, no dilution is required. 2 For smaller bodies of water, determine the size (in square feet) and the • Komeen + Endothall Tank Mix - Komeen can be mixed with endothall average depth (in feet) of the area to be treated. and applied as a uniform surface spray or injected under the water’s surface for control of species including naiad, curlyleaf pondweed, TABLE 4 elodea, coontail, watermilfoil, water stargrass, eelgrass, Cladophora, Average Water Fluid Ounces1 of Komeen per 1,000 ft2 to Pithophora, Spirogyra, Chara, American pondweed and sago Depth of Achieve the Desired Copper Concentration2 pondweed. For best results, apply Komeen/endothall combinations at a Treatment recommended ratio of 4:3 v/v Komeen to endothall formulated product Site (feet) 0.5 ppm 0.75 ppm 1.0 ppm (e.g., Aquathol® K/ Hydrothol® 191). 1 5.0 7.3 9.7 Flowing Water Treatment 2 9.8 14.7 19.3 Drip System or Metering Pump Application for Canals, 3 14.7 22.1 29.0 Ditches, and Laterals 4 19.6 29.4 39.0 For optimal control, apply Komeen as soon as submersed macrophytes or 5 24.5 36.8 49.0 algae begin active growth or interfere with normal delivery of water (clogging 6 29.4 44.2 58.7 of lateral head gates, suction screens, weed screens, and/or siphon tubes). 7 34.4 51.5 68.4 Delaying treatment could perpetuate the problem causing massing and 8 39.3 58.9 78.4 compacting of plants. Heavy infestations and low flows may result in pooling 9 44.2 66.2 88.1 or uneven product distribution resulting in unsatisfactory control. Under these 10 49.1 73.6 98.1 conditions repeated applications or increasing the water flow rate during application may be necessary. 1 When treating low volumes and measurements in tablespoons is desired, multiply the volume in fluid ounces by 2 to get the volume in tablespoons (one To achieve desired control with Komeen in flowing waters, maintain a fluid ounce contains two tablespoons). minimum exposure period of three hours at a concentration of 0.5 to 1.0 2 For surface applications, dilute Komeen with water in a minimum ratio of 4:1 ppm. Other factors to consider include: plant species, density of infestation (Komeen:water). For subsurface applications, no dilution is required.­­ and water temperature and hardness. Longer contact times and the highest METHODS OF APPLICATION rates may be required for less susceptible species or in difficult treatment conditions (e.g. dense weed beds, hard water, fast flowing water). Surface Application Spray Komeen from shore or boat across the surface of the targeted area. 1. Treatment with Komeen requires accurate calculations of water flow rates. Surface applications generally are recommended near shorelines and in Devices that provide accurate flow measurements such as weirs or orifices shallower waters, and may be made from shore into shallow water. are the preferred method; however, the volume of water to be treated may also be estimated using the following formula: Subsurface Application In deeper water, it is recommended to make a subsurface application of Cubic feet per second (cfs) = average width (feet) x average depth (feet) Komeen at listed rates through weighted trailing hoses in order to deliver x average velocity (feet/second) x 0.9 application mix to the water depth of target vegetation. Do not drag hoses on The velocity can be estimated by determining the length of time it takes a the bottom. Do not exceed 3.34 Gallons of Komeen per acre foot. floating object to travel a defined distance. Divide the distance (feet) by the Adjuvants/Surfactants time (seconds) to estimate velocity (feet/seconds). This measure should be Adjuvants or surfactants may be added to Komeen or to a Komeen/water repeated 3 times at the intended application site to calculate the average premix to improve efficacy.Silicone surfactants are not recommended velocity. for use on floating plants as they generally can cause the plant to 2. After accurately determining the water flow rate in cubic feet per sink causing the spray solution to be washed off the plant. Adjuvants/ second(s) (cfs) or gallons/minute, find the corresponding drip rate in surfactants may also enhance performance on other species. Consult the Table 5. For flow rates not listed in the table, multiply the flow rate by the manufacturer’s recommendations regarding the use of these products for recommended amount of Komeen in 1 cfs for application rates or use the improved control. below formula. Aerial Application cfs X 1.1 X desired concentration of metallic copper (ppm) Dilute Komeen with water in a minimum ratio of 4:1 (Komeen:water). Apply = quarts/hour of application the listed rate of Komeen in a recommended minimum of 10 gallons of total spray solution per surface acre. Add the listed rates of a drift control TABLE 5 or sinking agent to the spray solution. Maintain constant agitation during Komeen Application Drip or Injection Rates For Flowing Water addition of a polymer (except CA – polymers not approved for use with Water Flow Rate Komeen Drip Rate Komeen) and continue throughout the application. PPM Copper cfs gal / min. Quart / hr ml / min. Tank Mix 1 450 0.5 - 1.0 0.55 - 1.1 8.7 - 17.3 Komeen may be tank mixed with other herbicides for control of a broader 2 900 0.5 - 1.0 1.1 - 2.2 17.3 - 34.7 weed spectrum. Do not mix concentrates in tank without first adding water. 3 1,350 0.5 - 1.0 1.65 - 3.3 26.0 - 52.0 To ensure compatibility, a jar test is recommended before field application. 4 1,800 0.5 - 1.0 2.2 - 4.4 34.7 - 69.4 Komeen must not mixed with any product containing a label prohibition against such mixing and must be used in accordance with the more 5 2,250 0.5 - 1.0 2.75 - 5.5 43.4 - 86.7 restrictive of the label limitations and precautions. Do not exceed any label 10 4,500 0.5 - 1.0 5.5 - 11 86.7 - 173.4 dosage rates. 100 45,000 0.5 - 1.0 55 - 110 867.2 - 1,734.3 • Komeen + Sonar® A.S. Tank Mix - Komeen can be mixed with Sonar Calculate the amount of Komeen needed to maintain the drip rate for a A.S. to broaden the submersed weed control spectrum of either product treatment period of 3 hours by multiplying quart(s)/hour by 3 or milliliters/ alone and be applied as a uniform surface spray or injected under the minute by 180. For longer injection periods, multiply dosage rate by water’s surface. For best results, apply this tank mix at a minimum desired time in minutes or hours as appropriate. of 0.5 ppm Komeen and a low to moderate rate of Sonar A.S. Lower concentrations may be effective on more susceptible species and under Rates will target up to 1.0 ppm copper concentration in the treated certain conditions. water for the treatment period. Lower concentrations may be used on susceptible plant species or if longer exposure/injection times • Komeen + Diquat Tank Mix - Komeen can be mixed with diquat (diquat are maintained. Introduce Komeen in the channel at weirs or other dibromide) for enhanced control of certain weed species including turbulence-creating structures to promote the dispersion of the chemical. bladderwort, curlyleaf pondweed, leafy pondweed, Richardson’s pondweed, small pondweed, cattail, elodea, duckweed, water lettuce, Use a drum or tank equipped with a valve or other volume control device Eurasian watermilfoil, floating-leaf pondweed, coontail, salvinia, naiad, sago that can be calibrated to maintain a constant drip rate. Use a stopwatch pondweed, pennywort, Chara, hydrilla and water hyacinth. For best results, and appropriate measuring container to set the desired drip rate. Readjust apply Komeen/diquat (e.g. Littora®, Reward®) combinations in a 2:1 ratio accordingly if the canal flow rate changes during the treatment period. A of Komeen:Diquat. Do not exceed maximum labeled rates for any product. small pump or other metering device may be used to meter Komeen into the For hydrilla control and control of other species with high sensitivity to water more accurately. Application can be made using diluted or undiluted copper, lower rates of Komeen may also enhance the activity of diquat. material. Komeen must be applied at a minimum of 0.1 ppm in combination with diquat. Higher rates may be needed in areas with dense weeds. Results can vary depending upon species and density of vegetation, desired Warranty Disclaimer: SePRO Corporation warrants that this product distance of control and flow rate, and impact of water quality on Komeen conforms to the chemical description on the product label. Testing and and efficacy. Periodic maintenance treatments may be required to maintain research have also determined that this product is reasonably fit for the uses seasonal control (every 2 to 6 weeks). In addition, Komeen can be used in described on the product label. To the extent consistent with applicable law, a rotational program with other herbicides labeled for flowing water for an SePRO Corporation makes no other express or implied warranty of fitness integrated management approach. It is recommended to consult a SePRO or merchantability nor any other express or implied warranty and any such Technical Specialist to determine optimal use rate location of treatment warranties are expressly disclaimed. stations and duration of treatment period under local conditions. Misuse: Federal law prohibits the use of this product in a manner inconsistent Irrigation Ponds or Reservoirs with its label directions. To the extent consistent with applicable law, the When applying to irrigation ponds or reservoirs, it is best to hold water for a buyer assumes responsibility for any adverse consequences if this product is minimum of 3 hours before irrigating to ensure proper exposure of Komeen at not used according to its label directions. targeted rates to plants. If water is to be continually pumped from the treated In no case shall SePRO Corporation be liable for any losses or damages system during application, application techniques (drip, injection, or multiple resulting from the use, handling or application of this product in a manner spray applications) should be made to compensate for dilution of Komeen inconsistent with its label. within the targeted area. For additional important labeling information regarding SePRO Corporation’s STORAGE AND DISPOSAL Terms and Conditions of Use, Inherent Risks of Use and Limitation of Do not contaminate water, food, or feed by storage and disposal. Remedies, please visit http://seprolabels.com/terms or scan the image below. Pesticide Storage: Store in a cool dry place. Do not store near feed or foodstuffs. In case of leak or spill, use absorbent materials to contain liquids and dispose in a manner consistent with the pesticide disposal instructions. Pesticide Disposal: Pesticide wastes are acutely hazardous. Improper disposal of excess pesticide, spray mixture, or rinsate is a violation of Federal Law. If these wastes cannot be disposed of by use according to label instructions, contact your State Pesticide or Environmental Control Agency, or the Hazardous Waste representative at the nearest EPA Regional Office for guidance. Wastes resulting from the use of this product must be disposed of on site or at an approved waste disposal facility. Nonrefillable Container Handling (rigid, 5 gallons or less): Do not reuse or refill this container. Triple rinse container (or equivalent) promptly ©Copyright 2018 SePRO Corporation after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank and drain for 10 seconds after the flow begins to drip. Fill the container ¼ full with water and recap. Shake for 10 seconds. Pour rinsate into application equipment or a mix tank, treatment Komeen, Littora and Sonar are registered trademarks of SePRO Corporation. area, or store rinsate for later use or disposal. Drain for 10 seconds after Reward is a registered trademark of Syngenta Group Company. the flow begins to drip. Repeat the procedure two more times. Then offer Aquathol and Hydrothol are registered trademarks of United Phosphorus, Inc. for recycling (if available) or reconditioning, or puncture and dispose of in a sanitary landfill, or by incineration, or if allowed by state and local authorities, by burning. If burned, stay out of smoke. Nonrefillable Container Handling (rigid, larger than 5 gal): Do not reuse or refill this container. Triple rinse container (or equivalent) promptly after emptying. Triple rinse as follows: Empty the remaining contents into application equipment or a mix tank. Fill the container ¼ full with water. Replace and tighten closures. Tip container on its side and roll it back and forth, ensuring at least one complete revolution, for 30 seconds. Stand the container on its end and tip it back and forth several times. Turn the container over onto its other end and tip it back and forth several times. Empty the rinsate into application equipment or a mix tank, treatment area, or store rinsate for later use or disposal. Repeat this procedure two more times. Then offer for recycling (if available) or reconditioning, or puncture and dispose of in a sanitary landfill, or by incineration, or if allowed by state and local authorities, by burning. If burned, stay out of smoke.

SePRO Corporation 11550 North Meridian Street, Suite 600 Carmel, IN 46032, U.S.A.