0.39″ 4 bits Digital Tube LED horloge d’affichage couleur rouge sept segments anode commune 16 broches
0.39 inch 4 digital LED clock display -seven segment Display Digital: 4 Red Color Common Anode
Package included 1X 0.39” 4 Bits Digital Tube
0.96 “pouce I2C IIC série OLED LCD LED Module d’affichage blanc pour Arduino 51 MSP420 STIM32 SCR
Size: 0.96 Resolution: 128X64 Color: Blue Viewing angle: greater than 160 degrees Supported platforms: for arduino, 51 series, MSP430 series, STIM32 / 2, SCR chips Low power consumption: 0.04W during normal operation Support wide voltage: 3.3V-5V DC Working temperature: -30-80 degrees Volume: 27MM * 27MM * 4.1MM Driver IC: SSD1306 Communication: IIC, only two I / O ports No font: The software takes word modulo Backlight: OLED self light, no backlight
Interface: VCC: 3.3-5V GND: Ground SCL: Serial Clock SDA: Serial Data
Package Included:
1 X IIC OLED Module
1,3 pouces IPS LCD 240 x 240 avec interface SPI utilisant ST7789 Drive IC
1.6 nokia 5110 Module LCD avec rétro-éclairé bleu pour (pour Arduino)
Taille du PCB : 45 (mm) x 45 (mm)
Les coins étaient des trous de positionnement, ainsi que deux rangées du port de connexion supérieur et inférieur, classés comme suit :
VCC – entrée d’alimentation (3,3 v et 5 v disponibles)
GND – Terre
SCE – Sélection de puce
RST – Réinitialiser
D \ C – sélection de données / instructions
DN – Ligne de données série
CLK – Ligne d’horloge série
LED – console rétroéclairée
Le forfait comprend
1 module LCD 5110
1.8-inch TFT LCD module SPI module 51 drive
1.8 pouce TFT LCD module pour SPI série 51 MCU lecteur 1.8 pouce SPI série écran avec panneau de plancher module, à moins seulement 4 IO conduite taille: 1.8 Pouce SPI serial bus résolution: 128*160 conduire un MCU, fournir spécifications, 51 code du pilote et un ensemble complet de données
1602 AFFICHEUR LCD 2X16
Brand new and high quality LCD display module with blue blacklight Wide viewing angle and high contrast Built-in industry standard HD44780 equivalent LCD controller Commonly used in: copiers, fax machines, laser printers, industrial test equipment, networking equipment such as routers and storage devices LCM type: Characters Can display 2-lines X 16-characters Operate with 5V DC Viewing area is about 64×16 mm
Module dimension: 80mm x 36mm x 12mm Viewing area size: 64.5mm x 16mm
Package included: 1 X 1602 LCD display module 2.4 pouces 2.4 “TFT LCD Shield Module d’écran tactile TF Micro SD pour Arduino UNO R3 2560 R3
NOTE: you must use Arduino IDE 1.0.6
Bright, 4 white-LED backlight, on by default but you can connect the transistor to a digital pin for back light control Colorful, 18-bit 262,000 different shades 4-wire resistive touchscreen 8 bit digital interface, plus 4 control lines Uses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, 3 and analog 4 and 5. Pin 12 is available if not using the micro SD 5V compatible, use with 3.3V or 5V logic Size:72 x 52 x 12 mm
Package included: 1 x 2.4″ TFT LCD Shield SD Socket Touch Panel Module
2004 AFFICHEUR LCD 4X20
A 20 x 4 character LCD display with white text on a vivid blue backlit LCD. The pictures don’t do justice to the bright blue background with clear white text of this display.
4 lines of 20 characters.
Standard Hitachi HD44780 compatible interface for easy connection to microcontrollers Dimensions
Width 3.9 inches (98mm) Height 2.35 inches (60mm) Display view size 76mm x 26mm
3.0 “TFT LCD écran tactile stylo résistif 400*240 panneau de rupture pour Arduino UNO R3 Nano OPEN- SMART
Description : Il s’agit d’une carte d’extension LCD TFT de 3,0 pouces. Cet écran a un contrôleur intégré avec une mémoire tampon RAM, de sorte que presque tout le travail est effectué par le TFT. Il sort les broches du TFT et le pas des broches de rupture est de 2,54 mm, le développement secondaire est donc facile. Avec le module GPRS, vous pouvez concevoir votre téléphone. Avec le module de lecteur NFC, vous pouvez créer des systèmes de contrôle d’accès avec le spectacle de photos. Avec un capteur de tension et de courant, vous pouvez fabriquer un oscilloscope. Peut l’utiliser directement pour afficher des caractères, des graphiques et des images au format BMP à l’aide du module adaptateur de carte Micro SD. Compatibilité : comme le niveau logique est de 3,3 V, il est compatible avec la carte Arduino 3,3 V, vous devez généralement ajouter un circuit de conversion de niveau si vous utilisez une carte Arduino 5 V (Arduino UNO R3 / Arduino Mega2560 / Arduino Leonardo). Type d’écran tactile : écran tactile résistif. Stylet tactile : la longueur est de 9 cm ; Résolution : 400 * 240, 16 bits (262 000) couleur Taille de l’écran : 3,0 pouces ; Tension de fonctionnement : 3,3 V ; Niveau logique : 3,3 V ; Courant de fonctionnement : le maximum est de 150mA Interface de bus : interface parallèle 8080 (8 bits) Package de port IO : un PAD est disponible et le pas des broches est de 2,54 mm. La broche LED peut se connecter au circuit de contrôle de rétroéclairage externe pour contrôler la luminosité du rétroéclairage. Vous pouvez le connecter à GND pour allumer le rétroéclairage toute la journée. Très approprié pour cadre photo numérique, oscilloscope, générateur de fonctions, moniteur de système de détection
3.2″ Module d’affichage LCD TFT, panneau tactile, carte PCB, SSD1289, avec fente pour carte SD 65k, couleurs ILI934″
La description: Contrôleur à écran tactile ILI9341 régulateur de tension 3.3v Rétro-éclairage LED 320 x 240 pixels Couleur : 65536 Interface standard 37 broches
3.95 inch TFT LCD module for Raspberry Pi LCD screen, suitable for Raspberry Pi B +
Size: 3.95 Inch Lcd Ic: Ili9488 Resolution: 320×480 package list 3.95 Inch TFT Display for Raspberry Pi x 1
4 bits numérique tube conduit module d’affichage avec tm1637 d’affichage d’horloge pour Arduino raspberry pi 5-inch HDMI Raspberry Pi TFT Touchscreen LCD Screen
A good solution for those seeking for a bigger resolution display Designed for Raspberry Pi, an ideal alternative solution for monitor Supports any revision of Raspberry Pi (directly-pluggable) 800×480 resolution, better display Good touch response Large viewing angle Fast response time For Raspberry Pi B+/2B Raspberry Pi 3B With detail user guide and image
Specifications
5 inch TFT Resistive touch screen display, 800×480 Resolution HDMI input Usb touch and power, 5V@1A Lcd driver IC: ILI9486L Refresh rate:60HZ Lcd Size :120mm*78mm
Package list
5 inch Touch LCD Display x1 HDMI connector x1 Touch pen x1 CD x 1 7.0” Nextion Enhanced HMI Capacitive Touch Display With Enclosure Case
Nextion Enhanced NX8048K070_011C is a powerful 7.0” HMI TFT capacitive multi-touch display with a beautiful enlcosure, with 32MB Flash data storage space, 1024 byte EEPROM, 8192 byte RAM, and GPIO supported.
Features: Supports built-in RTC Supports GPIO SD Card interface: support max 32G Micro TF/SD card (FAT32 file format) Flash data storage space: 32MB EEPROM: 1024 bytes RAM: 8192 bytes Instruction buffer: 1024 bytes Color: 65K (65536) colors Resolution: 800×480 pixel Adjustable Brightness: 0~230 nit- the interval of adjustment is 1% CE/EMC, RoHS certified (certificates)
Package Includes: 1 X 7.0” Nextion Enhanced HMI Display with Enclosure
7inch HDMI LCD (B), 800×480, supports various systems
800×480 hardware resolution Capacitive touch control Supports popular mini PCs such as Raspberry Pi, BB Black, as well as general desktop computers When works with Raspberry Pi, supports Raspbian/Ubuntu/Kali/Retropie/WIN10 IOT, driver free When work as a computer monitor, supports Windows 10/8.1/8/7, five-points touch, and driver free Backlight can be turned off to lower power consumption Adaptateur d’extension IO série IIC I2C 1602 1604 2002 carte de module LCD pour Arduino
IIC/I2C/TWI/SPI Serial Interface to drive 2 and 4 line LCDs Simply solder it to the back of your Hitachi Style LCD and apply 4 wires. Requires only 2 data lines to display data on virtually every LCD made Compatible with Hitachi 1602, 1640, 2002, 2004, 4002 Interfaces I2C Address of 0x27
Supply voltage: +5 V Supports the I2C protocol With backlight and contrast adjustment potentiometer 4 Line Output easier
Package including: 1 X IIC I2C Serial Interface Adapter
Adaptateur intelligent pour rampes d’imprimante 3D 2004 contrôleur LCD avec ligne de fil Dupond Calbe 2 pièces 20 cm
Smart Adapter for 3D Printer Ramps 2004 LCD Controller Cable length: 30cm
Package Included: 1 X Smart Adapter 2 X Cables
Affichage numérique rouge à sept segments Anode commune du compteur numérique
Affichage numérique rouge à sept segments Compteur numérique à cathode commune AFFICHEUR 7 SEGEMENTS CATHODE COMMUNE 2 DIGITS DIM=0.56 POUCES VERT
Carte d’extension pour Nextion Enhanced Display I/O câble FFC étendu
La description:
La première carte d’extension pour l’affichage HMI Nextion Enhanced. Les écrans Nextion de version améliorée et supérieure prennent en charge 8 GPIO, nous pouvons donc utiliser cette carte d’extension pour contrôler Nextion. Le tableau a 6 boutons, qui incluent Esc, Enter, Gauche, Droite, Haut, Bas. En outre, le buzzer et les leds d’indication sont inclus. Remarque : cette carte d’extension ne peut fonctionner qu’avec l’affichage amélioré Nextion, pas pour l’affichage Nextion de base.
Contrôleur d’écran tactile USB résistif à 4 fils Pilote d’écran tactile à écran tactile LCD sans câble
D40 L60 CNC accouplement Flexible
Écran d’affichage à cristaux liquides TFT de 2,8 pouces avec module d’écran tactile coloré 240X320 pour Arduino
2.8 Inch TFT LCD Touch Screen Board ILI9341 TFT LCD Shield Touch Display Module 240X320 For Arduino UNO Color TFT Touch Panel Feature: 2.8 inch LCD TFT display Bright, 4 white-LED backlight Colorful, 18-bit 262,000 different shades 4-wire resistive touchscreen 240 x 320 pixels with individual pixel control No wiring, no soldering. Simply plug it in and load library On-board 3.3V 300mA LDO regulator 5V compatible, use with 3.3V or 5V logic Support 2GB micro SD TF card Size: 7.8 x 5.3cm Package included: 1 x 2.8 Inch TFT LCD Shield Touch Display Module
Écran LCD TFT 10,1 pouces avec carte de pilote HDMI + VGA + vidéo pour Raspberry PI
Écran tactile LCD TFT 2,8″ 8 bits 65K couleur 320 x 240 résolutions avec prise pour carte SD
ITDB02-2.8 module is 2.8″ TFT LCD with 65K color 320 x 240 resolutions. The controller of this LCD module is ILI9325DS, it supports 8bit and 16bit data interface with 4 wires control interface. Moreover, this module includes the touch screen and SD card socket.
Display Resolution 320 * 240 Display Interface
Parallel 8 Bit Parallel 16 Bit
Display Controller ILI9325C Expand
SD Card Socket Touch Screen
Board Size 76 x 51mm
Package Included: 1 X 2.8″ TFT LCD Touch Screen
Écran tactile résistif de 10,1 pouces à 4 fils
Gross Weight (kg): 0.1430 Manufacturer: EastRising Continuity Supply: We promise the long term continuity supply for this product no less than 10 years since 2015. Part Number: ER-TP101-1 Touch Panel Type: Resistive Touch Diagonal Size: 10.1“ Outline Dimension: 234.50(W)x142.50(H)x1.45(T)mm Visual Area: 223.80×126.90mm Active Area: 222.80(W)x125.90(H)mm Voltage: 5.0v Connection: FPC-Connector Operating Temperature: -20℃~70℃ Storage Temperatur: -30℃~80℃ MATRIX MAX7219 Kit de module de commande d’affichage à LED MCU pour module matriciel à LED pour Arduino
Module operating voltage: 5V A single module can drive an 8 * 8 common cathode lattice With four screws hole, aperture 3mm, by using our M3 Tongzhu fixed. Module with input and output interfaces, supports multiple modules cascade.
Wiring instructions: 1.The module left as an input port to the output port on the right. 2.The control of a single module, simply input port to the CPU. Multiple modules cascade input termination CPU, 2 output termination module, a module of the input of the input terminal, the output terminal of the first two modules of the first three modules, and so on … 51 MCU, for example:
VCC → 5V GND → GND DIN → P22 CS → P21 CLK → P20
Package Included: 1 X MAX7219 Dot Led Matrix Module MATRIX MAX7219 Module d’affichage à LED de microcontrôleur de module de matrice de points
A single module can drive an 8 x 8 common cathode lattice Operating voltage: 5V Size: 5 x 3.2 x 1.5 cm (L x W x H) LED color: red With four screws hole, aperture 3mm With input and output interfaces, supports multiple modules cascade
MAX7219 EWG Module de contrôle d’affichage de tube numérique à 8 chiffres rouge pour Arduino M61
MAX7219 is an integrated serial input / output common-cathode display drivers, which connects the microprocessor 7-segment digital LED display with 8 digits, you can also connect a bar graph displays or 64 independent LED. On which includes a B- type BCD encoder chip, multi-channel scanning loop, segment the word drive, but also an 8 * 8 static RAM for storing each data. Only one external register is used to set the segment current of each LED.
Display: 0.36″ 4 digit led display 7 seg segment Common cathode Red Power: 5V Material: PCB + Electronic Components Size: 82 * 15 * 18mm Color: Red Wiring instructions (for example, it can connect any IO port, modified the Port Definition in the program):
VCC → 5V
GND → GND
DIN → P00
CS → P01
CLK → P02
Package Included: 1 X MAX7219 Module 1 X 5P Straight Pin 1 X 5P Bent Pin
MCP23017 12864 128 * 64 LCD I2C IIC TWI SPI interface série adaptateur plaque carte convertisseur module pour Arduino 1602 2004 avec broches
Module d’affichage à LED matriciel 5mm 8×8 Anode commune rouge 60x60mm 16pin
LED Display Dot Matrix Common Anode,Red color 8×8, 5mm 60x60mm,16pin 10mcd,640nm 1.8V forward voltage
Package Included: 1 X Dot Matrix LED Display Module
Module d’affichage LCD 3.5 pouces Waveshare Raspberry Pi 800*480 TFT panneau d’écran tactile résistif Interface HDMI pour tout modèle de Rapsberry pi
Module d’affichage LCD 5 pouces Waveshare Raspberry Pi 800*480 TFT panneau d’écran tactile résistif Interface HDMI pour tout modèle de Rapsberry pi
Plug the LCD to your Raspberry Pi: There are 40 pins on Raspberry Pi Model A+/B+/2 B/3 B but only 26 pins on the LCD, so you should pay attention to connecting the pins to your Pi accordingly. Connect the HDMI Connector to both the HDMI interfaces on the LCD and the Pi. You should connect the LCD to Raspberry Pi Model B or Raspberry Pi Zero with an HDMI cable rather than an HDMI Connector. Turn on the “backlight” switch on the back of the LCD. Module d’affichage LCD OLED 0.91 ” 128×32 I2C IIC série blanc 0.91 pouces 12832 SSD1306 écran LCD pour Arduino
Resolution Ratio:128*32 Color:white Driving IC:SSD1306 IIC Interface Definition:GND,VCC,SCL,SDA Voltage:3.3-5V Connection:
0.91’’ oled Arduino uno r3
GND GND
VCC 3.3V
SCL A5
SDA A4
Module d’écran tactile LCD TFT 3,5 pouces pour carte Arduino UNO Mega2560 carte d’affichage d’écran LCD 480×320
Module Ecran LCD 1602 Avec Clavier pour Arduino BLEU
This is a 16×2 LCD Keypad module for ARDUINO / Arduino Diecimila Duemilanove / FREEDUINO board.. Blue Backlight with white words Uses 4 Bit Arduino LCD Library 100% brand new and high quality
The Modified LCD4Bit library and Schematic will send by email.
GP2D12 ranging code:
#include
LCD4Bit_mod lcd = LCD4Bit_mod(2); char GP2D12; char a,b; char str1[]=”Renge:”; char str2[]=” Renge Over “; char str3[]=”cm”; void setup() { lcd.init(); lcd.clear(); lcd.printIn(“GP2D12 testing…”); } void loop() { GP2D12=read_gp2d12_range(1); if(GP2D12>80||GP2D12<10) { lcd.cursorTo(2,0); lcd.printIn(str2); } else { a=0x30+GP2D12/10; b=0x30+GP2D12%10; lcd.cursorTo(2, 3); lcd.printIn(str1); lcd.print(a); lcd.print(b); lcd.printIn(str3); } delay(50); } float read_gp2d12_range(byte pin) { int tmp; tmp = analogRead(pin); if (tmp < 3)return -1; return (6787.0 /((float)tmp – 3.0)) – 4.0; }
Package Included:
1 x Keypad Shield LCD 1602 Module matriciel MAX7219 MATRIX pour microcontrôleur Arduino 4 EN 1 affichage avec ligne 5P
Operating Voltage: 5V. Dimensions: 12.8X12.8X1.3c. Fixing screws with 64 holes with a diameter 3mm. A single module can drive a 8×8 dot matrix common cathode. Module with input and output interfaces, support for cascading multiple modules.
Nextion NX1060P101-011C-I Écran tactile capacitif LCD TFT HMI 10,1 pouces 1024 * 600
Hardware Features – NX1060P101-011C-I(10.1” IPS RGB 65K capacitive touchscreen) – Onboard MCU 200MHz and up to 128MB for HMI project – Built-in RTC,EEPROM, 8 digital GPIOs (2 PWM capable) – 4 pins (+5V, TX, RX, GND) TTL serial interface – 300 nit Brightness with 1% interval adjustment – Audio interface – CE and RoHS Compliant – Model: NX1060P101-011C-I(HMI Capacitive Touch Display)
Model Name:NX1060P101-011C-I Size: 10.1” Resolution: 1024*600 Touch Panel: CTP Color: 65536 Flash: 128MB RAM: 512KB MCU: 220MHz EEPROM: 1024 Byte GPIOs: 8 RTC: Yes Enclosure: No
Nextion NX8048T070 Écran tactile TFT LCD 7 pouces HMI intelligent module USART pour Arduino, Raspberry Pi ET ESP8266
Nextion is a Seamless Human Machine Interface (HMI) solution that provides a control and visualisation interface between a human and a process, machine, application or appliance. It is the best solution to replace the traditional LCD and LED Nixie tube.
This solution includes hardware part – a series of TFT boards and software part – Nextion editor. Nextion TFT board uses only one serial port to do communicating. Let you get rid of the wiring trouble. We notice that most engineers spend much time in application development but get unpleasant results. In this situation, Nextion editor has mass components such as button, text, progress bar, slider, instrument panel etc. to enrich your interface design. And the drag-and-drop function ensures that you spend less time in programming, which will reduce your 99% development workloads. With the help of this WYSIWYG editor, GUI designing is a piece of cake.
It’s easy to adapt Nextion family HMI to existing projects, you just need to provide it a UART.
This is a powerful 7.0” HMI, which is member of Nextion family. Features include: a 7.0″ TFT 800×480 resistive touch screen display, 16M Flash, 2KByte RAM, 65k colors.
Features:
800 x 480 Resolution RGB 65K true to life colours TFT Screen with integrated 4-wire Resistive Touch Panel Easy 4 pin interface to any TTL Serial Host 16M Flash memory for User Application Code and Data On board micro-SD card for firmware upgrade Visual Area:154.08mm(L)×85.92mm(W) Adjustable Brightness:0~230 nit, the interval of adjustment is 1% 5V510mA power conusmption datasheet link https://www.itead.cc/wiki/NX8048T070 software link http://nextion.itead.cc/download.html Package Included: 1 X 7.0″ HMI LCD Display Module 1 X 4P Cable 1 X UB to 2pin connector NX4827T043 Nextion 4.3 ” Module d’affichage tactile LCD TFT HMI
La description: Nextion est une solution d’interface homme-machine transparente (HMI) qui fournit une interface de contrôle et de visualisation entre un humain et un processus, une machine, une application ou un appareil. C’est la meilleure solution pour remplacer le tube LCD et LED Nixie traditionnel.
Cette solution comprend une partie matérielle – une série de cartes TFT et une partie logicielle – l’éditeur Nextion. La carte Nextion TFT utilise un seul port série pour communiquer. Vous permet de vous débarrasser des problèmes de câblage. Nous remarquons que la plupart des ingénieurs passent beaucoup de temps dans le développement d’applications mais obtiennent des résultats désagréables. Dans cette situation, l’éditeur Nextion comporte des composants de masse tels que des boutons, du texte, une barre de progression, un curseur, un tableau de bord, etc. pour enrichir la conception de votre interface. Et la fonction glisser-déposer garantit que vous passez moins de temps à programmer, ce qui réduira vos charges de travail de développement de 99%. Avec l’aide de cet éditeur WYSIWYG, la conception d’interface graphique est un jeu d’enfant.
Il est facile d’adapter l’HMI de la famille Nextion aux projets existants, il vous suffit de lui fournir un UART.
NX2432T043 est une puissante HMI de 4,3 ”, membre de la famille Nextion. Les caractéristiques incluent : un écran tactile résistif TFT 480×272, 16M Flash, 2KByte RAM, 65k couleurs.
Caractéristiques:
Résolution 480 x 272 Couleurs RVB 65K fidèles à la réalité Écran TFT avec panneau tactile résistif à 4 fils intégré Interface simple à 4 broches vers n’importe quel hôte série TTL Mémoire flash de 16 M pour le code et les données de l’application utilisateur Carte micro-SD intégrée pour la mise à niveau du firmware Zone visuelle : 95,04 mm (L) × 53,86 mm (L) Luminosité réglable: 0 ~ 230 nit, l’intervalle de réglage est de 1% Consommation électrique 5V250mA
NX4832T035 Nextion 3.5” Module d’affichage tactile LCD TFT HMI”
La description: Nextion est une solution d'interface homme-machine transparente (HMI) qui fournit une interface de contrôle et de visualisation entre un humain et un processus, une machine, une application ou un appareil. Nextion est principalement appliqué au domaine de l'IoT ou de l'électronique grand public. C'est la meilleure solution pour remplacer le tube LCD et LED Nixie traditionnel.
Cette solution comprend une partie matérielle - une série de cartes TFT et une partie logicielle - l'éditeur Nextion. La carte Nextion TFT utilise un seul port série pour communiquer. Vous permet de vous débarrasser des problèmes de câblage. Nous remarquons que la plupart des ingénieurs passent beaucoup de temps dans le développement d'applications mais obtiennent des résultats désagréables. Dans cette situation, l'éditeur Nextion comporte des composants de masse tels que des boutons, du texte, une barre de progression, un curseur, un tableau de bord, etc. pour enrichir la conception de votre interface. Et la fonction glisser-déposer garantit que vous passez moins de temps à programmer, ce qui réduira vos charges de travail de développement de 99%. Avec l'aide de cet éditeur WYSIWYG, la conception d'interface graphique est un jeu d'enfant.
Il est facile d'adapter l'HMI de la famille Nextion aux projets existants, il vous suffit de lui fournir un UART.
Il s'agit d'une puissante HMI 3,5'', membre de la famille Nextion. Les caractéristiques incluent : un écran tactile résistif TFT 480 x 320 de 3,5 pouces, 4M Flash, 2KByte RAM, 65k couleurs.
Caractéristiques: Résolution 480x320 Couleurs RVB 65K fidèles à la réalité Écran TFT avec panneau tactile résistif à 4 fils intégré Interface simple à 4 broches vers n'importe quel hôte série TTL Mémoire flash de 16 M pour le code et les données de l'application utilisateur Carte micro-SD
OLED 0.66 Inch OLED Display Shield Pour Carte IoT 3.3V
Support de coque pour écran LCD 1602
TFT MEGA Shield pour Arduino
MEGA shield support both 3.3V mainboard and 5V mainboard, so it not just can be used with for Arduino MEGA but can with other for Arduino MEGA compatible mainboards , like ChipKit MAX32.
Note: It does not support Iteaduino Mega.
Package Included: 1 X MEGA Shield
Tube numérique de 0,56 pouces une nuance commune rouge Voltmètre numérique AC70-500V 0.56 pouces LED rouge 2câble
Minimum Resolution: 1v Input Impedance:> 1MΩ Speed Measurement: ≥2 times / S Operating Temperature: -10- + 50 Operating Humidity: 10-80% (No Condensation) Working Pressure: 80 ~ 106kPa Wire length: 200mm Case Color: Black Product Size: 48 × 29 × 22mm
Hole Size: 46 × 27mm
1x Voltmeter