DOCSLIB.ORG

Dual Clutch Transmission and Performance Catalogue

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Dual Clutch Transmission and Performance Catalogue DUAL CLUTCH TRANSMISSION AND PERFORMANCE CATALOGUE INTRODUCTION 1 NEW PRODUCT 2015 2 DMS GT-CAR 3 NISSAN R35 GTR 4 MITSUBISHI EVO X 16 VW/AUDI 20 BMW 22 PORSCHE 24 MERCEDES 25 DISTRIBUTORS 26 PRO DEALERS 26 DEALERS 29 www.dodsonmotorsport.com Since the early 90’s, Dodson Motorsport has been at the forefront of Nissan race car development from it’s base in New Zealand. Today Dodson Motorsport products are available worldwide through a network of fully trained and approved dealers equipped with specialised tools and manuals. In recent times DMS high performance Nissan R35 GTR Dual Clutch Transmission components have reinforced their worldwide reputation for innovation, quality and superior performance. The Dodson Motorsport racing team’s considerable experience has helped develop all of their products. Countless hours of CAD design and track testing has resulted in a succesful range of dual clutch components for the GTR, BMW, VW, AUDI, MITSUBISHI, MERCEDES and now LAMBORGHINI and PORSCHE. Along with friction partner Exedy in the USA, Dodson Motorsport components reduce heat, increase power, delivery, grip, output and reliability to suit road, race or drag race applications. Recent noteworthy record achievements using DMS products include the world’s fastest and quickest R35 GTR, AMS Alpha Omega R35 GTR achieving the quarter mile in 7.48 seconds at 192MPH. Theo Perimenis achieved 8.295 seconds at 275 KPH to become the fastest GTR in Europe. USA Dodson Motorsport dealer John Shepherd achieved 8.28 seconds at 172 MPH for the world radial record. Exelixis built Audi TFSI driven by Mike Drag has become the worlds first DSG TFSI in the 8 second club and Kozmic Motorsports in the USA have achieved the worlds first SST in the 9 second club. So whether your requirements are for peace of mind motoring, or all out racing, Dodson Motorsport has Dual Clutch Transmission Components to suit your application. 1 NEW PRODUCT 2015 With Dual Clutch transmissions becoming predominant in the high performance market, the need for upgraded clutches to cater was always going to be necassary. Dodson Motorsport have developed a range of clutches to suit the Audi R8 and Lamborghini Huracan that have the ability to handle above your OEM power range. Both Super Stock and Sportsmans options will be available for supply and in time a High Power 2000hp Promax will become available. The Dodson Porsche clutch has been developed to increase the capability of your PDK clutch. With the aftermarket Porsche scene growing world-wide, there came the need to develop a clutch to cope with power upgrades. Dodson Motorsport have produced a PDK clutch capable of increased power levels. Dodson Motorsport have developed an upgraded clutch for the DQ500 transmission found most commonly in the Volkswagen Golf R and Audi TT. This is a 7 speed wet clutch upgrade, which will have a superstock option available, in time there will also be a sportsman option available. For all inquiries please contact : [email protected] 2 DMS GT-CAR GT 121-DMS GT CAR For some time now the Dodson Motorsport GT Car has been in production, after testing and various setups it is on the final stretch of being complete and put on the race track. After the first dyno tune had taken place GT121 had booked in over 1000hp. Keep an eye out for a further release and photo’s of the Dodson Motorsport GT- Car out on the race track being put through its paces. 3 Dodson Motorsport along with friction partner Exedy in the USA, have developed a comprehensive range of world leading performance clutches for the GR6 Transmission. From Super Stock right through to Promax Kits available Dodson Motorsport will be sure to cater a clutch best suited to your R35. The Nissan R35 GT-R’s legendary ability to produce substantial power from its engine, and grip from its four wheel drivetrain places huge demands on all of the GR6’s transmission components. Dodson Motorsport’s Upgraded Dual Clutch components allow your R35 to handle not only higher horspower and torque, but reduce heat, improve reliabilty for street use and also handle your full 2000hp build. 4 T1 Race Developments R35 GTR Currently the worlds fastest R35 GTR over 1500ft Roll Start. 210mph at the Texas Invitational as of October 2015 Extreme Turbo Systems R35 GTR Previous 1/4 Mile world record holder as of March 2015 Previous Record : 7.492 seconds @ 189.20 mph 5 Clutches R35 CPMA11 R35 CPMA10 R35 CSKA9 PROMAX® + FORGED PROMAX® + FORGED SPORTMANS® + FORGED ALLOY PISTONS 11 PLATE ALLOY PISTONS 10 PLATE ALLOY PISTONS 9 PLATE CLUTCH KIT CLUTCH KIT CLUTCH KIT R35 CSKA8 R35 CSS R35 FWDCP SPORTMANS® + FORGED SUPER STOCK 7 PLATE UPGRADED FWD PISTONS 8 PLATE HP CLUTCH KIT CLUTCH PACK CLUTCH KIT R35 CF R35 CPS CLUTCH FRICTION CLUTCH PACK SHIM FROM 1.2MM TO 2.4MM 6 DODSON EXTREME DUTY 6 SPEED GEAR SET. (ED6SGS2 / ED6SGS2OD) AVAILABLE IN BOTH OVERDRIVE AND STANDARD RATIOS. Gears & Shafts R35 ED1GK2 R35 ED6SGS2 R35 ED6SGS2OD EXTREME DUTY 1ST EXTREME DUTY 6 EXTREME DUTY 6 SPEED GEAR SET SPEED GEAR SET GEAR SET OVER DRIVE R35 EDOS R35 EDFOSG R35 EDFWDP EXTREME HEAVY DUTY EXTREME DUTY FWD EXTREME DUTY FWD GR6 OUTPUT SHAFT & PINION GEAR OUTPUT SHAFT LOCK R35 GSS 35 R35 GSS 246 R35 HDFP UK GEAR SELECTOR SHAFT GEAR SELECTOR SHAFT HEAVY DUTY FRONT 3RD & 5TH GEARS 2,4,6 GEARS PROP SHAFT UPGRADE KIT R35 MAINSHFTPLATE MAIN SHAFT END PLATE 7 Upgraded GR6 Parts R35 CAF R35 CBF R35 CCC FORGED CLUTCH FORGED CLUTCH BASKET CLUTCH CENTRE BASKET OUTPUT A (2,4,6) OUTPUT B (1,3,5,R) CIRCLIP (SET OF 5) R35 CBG1 R35 246CB 246 CLUSTER BEARING #1 R35 CBG2 246 CLUSTER BEARING 246 CLUSTER BEARING #2 R35 CH CIRCLIP R35 CLUTCH CS 15 R35 CLUTCH CS 20 CLUTCH HOUSING PROMAX® CLUTCH PROMAX® CLUTCH CIRCLIP FROM 1.4MM TO CENTRE SHIM 2012 CENTRE SHIM 2012 2.4MM ONWARDS ONWARDS R35 DCS R35 DS R35 EISFB HIGH TEMP DIFF SIDE DIFF SCOOP ENGINE INPUT SHAFT COVER SEAL FRONT BEARING R35 FCB R35 FWD CHB R35 FWD CHEMB FRONT CLUSTER FWD CLUTCH HOUSING CLUTCH HOUSING BEARING BEARING ELECTRO MAGNET BEARING R35 BILLET DIFF COVER BILLET DIFF HOUSING COVER WITH WATER GALLERY 8 R35 FWD OB R35 FWD OBU KIT R35 FWD ORING FWD OUTPUT BEARING FWD OUTPUT BEARING FWD HOUSING ORING UPGRADE KIT R35 FWD OSS R35 FWD TGB R35 FWD TW FWD OUTPUT SHAFT FWD TRANSFER GEAR FWD THRUST WASHER SEAL BEARING R35 FWDH NUT R35 FWDCH R35 FWDH SEAL R35 FWD CLUTCH HEAVY DUTY FWD FWD HOUSING LOWER HOUSING NUT CLUTCH HOUSING SEAL R35 GL R35 GP1 R35 GP2 FWD HEAVY DUTY GEAR GEAR SELECTOR GEAR SELECTOR LOCK PISTON 1 PISTON 2 R35 GPAS R35 GR6 ASP R35 GR6 VB TRANS ANTI SURGE ACTUATOR SHIM FOR CLUTCH GP1 & GP2 PLATE SOLENOID R35 GR6 VB R35 GR6 VB R35 GR6 VBG 1 MAIN SOLENOID OIL PUMP VALVE BODY GASKET 1 SOLENOID 9 R35 GSH 1R R35 GR6 VBG 2 R35 GR6 VBG3 GEAR SELECTOR HUB VALVE BODY GASKET 2 VALVE BODY GASKET 3 1ST & REVERSE R35 GSH 35 GEAR SELECTOR HUB R35 GSH 24 R35 GSH 6 3RD & 5TH GEARS GEAR SELECTOR HUB GEAR SELECTOR HUB 2ND & 4TH GEARS 6TH GEAR R35 GSR R35 GSR 6 R35 HDSFB 1R GEAR SELECTOR RING GEAR SELECTOR RING HEAVY DUTY BILLET FOR 6TH GEAR SELECTOR FORK FOR 1ST & REVERSE R35 HDSFB 24 R35 HDSFB 35 R35 HDSFB 6 HEAVY DUTY BILLET HEAVY DUTY BILLET HEAVY DUTY BILLET SELECTOR FORK FOR 2 SELECTOR FORK FOR 3 SELECTOR FORK 6TH & 4 GEARS & 5 GEARS GEAR R35 HDSF BEARING R35 ISCB R35 ISEB HEAVY DUTY SHIFT INPUT SHAFT CENTRE INPUT SHAFT END FORK BEARING BEARING BEARING R35 LPS 3 R35 ISS R35 LPS2 INPUT SHAFT SEALS INSTALL KIT LINE PRESSURE LINE PRESSURE SENDER - PAIR SENDER 3 INSTALL KIT 10 R35 MC1 2MM R35 MC1 R35 MC2 GR6 MECHANICAL GR6 MECHANICAL GR6 MECHANICAL CIRCLIP CIRCLIP CIRCLIP R35 MSCB R35 MSFB R35 MSRB MAINSHAFT CENTRE MAINSHAFT FRONT MAINSHAFT REAR BEARING BEARING BEARING R35 MTW3G R35 MTW6G R35 MTB MAINSHAFT UPGRADED MAINSHAFT UPGRADED MAINSHAFT THRUST THRUST WASHER 3RD THRUST WASHER 6TH BEARING GEAR GEAR R35 MTWRG R35 MVBREPKIT R35 OPK MAINSHAFT UPGRADED REPAIR KIT FOR MAIN OIL PUMP UPGRADE THRUST WASHER VALVE BODY AND REPAIR REVERSE GEAR R35 OPP R35 ORK R35 OSB1 HEAVY DUTY ALLOY GR6 ORING KIT OUTPUT SHAFT GASKET PLATE BEARING 1 R35 OSEF SHIM R35 PALF R35 PBLF OUTPUT SHAFT END FORGED ALLOY PISTON FORGED ALLOY PISTON FLOAT SHIM A & SEAL (2,4,6) B & SEAL (1,3,5,R) 11 R35 PFK R35 PSS R35 RDSB TRANS PAN MAGNET KIT PISTON SHAFT SEALS REAR DIFF SIDE BEARING R35 RIGB R35 RSS ALLOY R35 SRC REVERSE IDLER GEAR HEAVY DUTY CLUTCH HEAVY DUTY CLUTCH BEARING RETURN SPRING SEAL RETURN SPRING RETAINER CLIPS R35 SYNCRO SET R35 TBC2 135 R35 TBC2 246 GR6 SYNCRO SET THRUST BEARING THRUST BEARING CIRCLIP 1,3,5 GEARS CIRCLIP 2,4,6 GEARS R35 TF R35 TP R35 TPF TRANSMISSION FILTER DRAG/CIRCUIT GR6 TRANS PAN REUSABLE FOR GR6 BILLET ALLOY TRANS FILTER FOR R35 GR6 TRANSMISSION PAN SUMP DRAG AND TRANSMISSION CIRCUIT OPTIONS R35 THXK R35 TRANS R35 VBF TRANSMISSION HEAT COOLER ALLOY VALVE BODY EXCHANGER KIT-WITH TRANSMISSION COOLER FILTER LOW TEMP THERMOSTAT KIT 12 Engine Parts R35 1000INJ R35 DMS MOTEC R35 DMS MOTEC VR38 1000CC INJECTOR M1 LHD M1 RHD KIT MOTEC DHB R35 MOTEC LTCD R35 EGR BLANK DUAL HALF BRIDGE NTK EXHAUST GAS LAMBDA TO CAN BLANKING KIT R35 ETS R35 FPAK R35 FPS VR38 LOW TEMP FUEL PRESSURE FUEL PRESSURE THERMOSTAT ADAPTOR KIT WITH SENDER SENDER R35 LTTME R35 OFC R35 OTS VR38 LOW TEMP DMS OIL FILLER CAP OIL TEMP SWITCH THERMOSTAT FOR MIDDLE EAST OR HOT CLIMATES R35 RHK R35 TS R35 TPS R35 GTR SILICON WASTEGATE KIT TYRE PRESSURE RADIATOR HOSE KIT VR38 TURBO WASTE SENSOR GATE UPGRADE KIT 13 Suspension R35 BILLET FUA R35 LRAC R35 LRAT HEAVY DUTY BILLET REAR LOWER ARMS FOR REAR LOWER ARMS FOR ADJUSTABLE FRONT CAMBER ADJUSTMENT TOW ADJUSTMENT UPPER ARMS Accessories DMS TEMP
Load more

Recommended publications
  • Civic Jdm Rear Licence Plate Holder
    Civic Jdm Rear Licence Plate Holder Derek is clean consanguineous after crosswise Christian blob his dependant hypocritically. Achondroplastic Filip decree approximately. Caucasoid Munmro never outfrowns so obtusely or scramblings any grinders thankfully. We missing a huge selection of Genuine Honda Parts across the entire footprint of Honda models, Tomei, and accessories. If we can change according to block the size number plates do look like. JDM front end conversion with the license plate holder area shaved off? If you must wear a problem calculating your jdm engine bay sold secondhand to see and margins for authenticity in. In order to use this website and its services, and clickbait titles. Your jdm rear of a pair of this? Consumer Reports or Google Reviews. Your order to respectfully share your desire is too large to avoid vague, plastic that included. All the licence plate holder, and ukdm categories which can always have ordered has deliberately selected a pair of several cars is to. Availability: In Stock; Qty. Car & Truck Suspension & Steering Parts 96-00 Honda Civic. You have exceeded the Google API usage limit. Cox Motor Parts, please specify when ordering. Copyright the rear license plate off the actually stamped for honda? Actual product may vary. Copyright The Closure Library Authors. EBay Motors Parts Accessories Car Truck Parts DecalsEmblemsLicense Frames License Plate Frames. Product is it legal minimum of honda. All, those stroke, rear disc conversion and very much more. Honda civic rear disc brakes of your jdm front or register to eliminate any other similar bolts for the licence plate to the subreddit may not satisfied with intake for the reason.
    [Show full text]
  • Nissan Ud Auto and Manual Gearbox
    Nissan Ud Auto And Manual Gearbox If searching for the book Nissan ud auto and manual gearbox in pdf format, in that case you come on to the right site. We present the utter option of this book in doc, PDF, txt, ePub, DjVu formats. You may reading Nissan ud auto and manual gearbox online either downloading. In addition to this book, on our site you may read the guides and diverse artistic eBooks online, either download their as well. We will draw on your attention that our website not store the eBook itself, but we give ref to site whereat you may downloading either read online. So if you need to load pdf Nissan ud auto and manual gearbox, then you have come on to correct website. We have Nissan ud auto and manual gearbox PDF, ePub, doc, txt, DjVu formats. We will be pleased if you come back to us anew. Nissan UD: eBay Motors | eBay View all Nissan Nissan UD. Nissan UD 1800; Nissan UD 1400; Nissan UD Truck; Browse Related. Browse Related. Mitsubishi Fuso; Isuzu NPR; Hino Truck; The Nissan UD Welcome to UD Trucks With its headquarters located in Ageo, Japan, UD Trucks supports sales and services in more than 60 countries through a worldwide network. Nissan Xterra Manual Transmission Problems - Car Forums at Nonetheless I've driven 2 different makes also manual transmission for a total of It is still hard to believe a major Japanese car co such as Nissan would UD Heavy Truck Repair Manuals, Diagnostic Scanners & Software BEST BRANDS REPAIR MANUALS Auto, If you can't find the UD Medium / Heavy Truck Repair Manuals, UD Works with Hino, Isuzu, Nissan, UD or OBD-II in Standard Car: Nissan UD Truck Transmission / Gearbox.
    [Show full text]
  • Annual Report 2018 1 Corporate Information
    CONTENTS Page Corporate Information 2 Financial Highlights 4 Chairman’s Statement 5 Management Discussion and Analysis 8 Corporate Governance Report 19 Directors and Senior Management 35 Report of the Directors 38 Independent Auditor’s Report 50 Consolidated Statement of Profit or Loss 56 Consolidated Statement of Comprehensive Income 57 Consolidated Statement of Financial Position 58 Consolidated Statement of Changes in Equity 60 Consolidated Statement of Cash Flows 61 Notes to Financial Statements 63 Five-Year Financial Summary 174 ANNUAL REPORT 2018 1 CORPORATE INFORMATION BOARD OF DIRECTORS JOINT COMPANY SECRETARIES Executive Directors Ms. XU Xing (appointed on 20 November 2018) Ms. CHENG Mei Chun Mr. LI Jianping (Chairman) Mr. WANG Xinming (President) Mr. QI Junjie AUTHORISED REPRESENTATIVES Mr. LU Ao Mr. LI Jianping Ms. XU Xing (re-designated from Ms. XU Xing non-executive Director on 8 June 2018) STOCK CODE Non-Executive Director 1293 Mr. Zhou Yu (resigned on 10 May 2018) WEBSITE Independent Non-Executive Directors www.klbaoxin.com Mr. DIAO Jianshen Ms. LIU Yangfang (appointed on 8 June 2018) Mr. CHAN Wan Tsun Adrian Alan PRINCIPAL PLACE OF BUSINESS Mr. WANG Keyi (resigned on 8 June 2018) AND HEAD OFFICE IN THE PRC No. 3998 Hongxin Road AUDIT COMMITTEE Minhang District, Shanghai, PRC. Mr. DIAO Jianshen (Chairman) Ms. LIU Yangfang (appointed on 8 June 2018) PRINCIPAL PLACE OF BUSINESS Mr. CHAN Wan Tsun Adrian Alan IN HONG KONG Mr. WANG Keyi (resigned on 8 June 2018) Level 54, Hopewell Centre, 183 Queen’s Road East, REMUNERATION COMMITTEE Hong Kong. Mr. DIAO Jianshen (Chairman) REGISTERED OFFICE Mr. LI Jianping Ms.
    [Show full text]
  • USGT Class Rules and Specifications As of 3-8-2021
    USGT Class Rules and Specifications as of 3-8-2021 Chassis Specification: Any 1/10 4wd or Fwd sedan with 4 wheel independent suspension Weight Specification: 4wd Minimum 1350g in race-ready trim Fwd no minimum weight Ride Height Specification: Minimum ride height is 5mm on Carpet Tire & Wheel Specifications: Tires- ​ Note: JANUARY 1 2014 The Ride spec tire will become the official spec tire for USGT RIE24025 - set of 4 available through Gravity RC http://www.teamgravityrc.com/ to dealers and retail Tires- RIE24025 - set of 4 available through Gravity RC http://www.teamgravityrc.com/ to dealers and retail Grinding of tire tread is NOT permitted. Sanding of mold seam to remove seam is allowed MUST USE INCLUDED INSERTS Wheels- Any 24mm - 26mm spoke (non-dish) type wheel ​ Motor Specifications: The only legal motor for USGT will be the USGT Spec motor #GRC2000 USGT SPEC MOTOR RULES GRAVITYRC #GRC2000: ​ ​ NO rotors, sensors or stators outside of the below specification provided will be considered legal. Aluminum or stainless steel main can or end bell screws are prohibited for USGT competition. MOTOR TECH CHECKLIST: MEASUREMENTS TAKEN AT ROOM TEMPERATURE OF 75DEG F* AVERAGE STATOR POLE RESISTANCE: (TOLERANCE 30.0--30.7 ohms) AVERAGE TIMING AT 5,000RPM: (TOLERANCE 30--33deg) TOTAL SENSOR GAP: (TOLERANCE 0--3deg) ROTOR ALIGNMENT: (TOLERANCE 0--5deg) (These measurements were developed by Gravity RC with their in house test equipment. For assistance with motor technical inspection for your race or club track, contact Gravity RC at [email protected]​ )​ ​ ROTOR: Must use stock rotor - USGT logo engraved on shaft Approved ESCs: ANY ESC that is ROAR approved and using ROAR approved “Blinky” spec software or on the USVTA list Battery Specifications: Any 7.4v - 7.6v 2s ROAR approved hard case batteries.
    [Show full text]
  • Turbo Dynamics Limited – Press Release – 11/10/10 Td
    TURBO DYNAMICS LIMITED – PRESS RELEASE – 11/10/10 TD Turbos Triumph at Time Attack Final The final round of Time Attack at Snetterton on 10th October proved a nail biting affair. There was no predetermined winner in any class and the competitors had it all to play for. Turbo Dynamics’ partners Car Planet Racing flowed success throughout the day. Gareth Lloyd won Pro Class in Car Planet Racing’s EVO achieving a Time Attack record 1:08.299secs lap winning him Round 5 and put him into Time Attack history as the 2010 Pro Class Champion. James Nicholls, also in a CPR EVO, came fourth with a best lap of 1.12.010 secs. Also running in Pro Class, TD Partner Lateral Performance’s Subaru Imprezza driven by Gavin Renshaw with a 1:11.163secs time came a well deserved third place. One of the most exciting classes was the Club Challenge 4WD, being the most competitive of the year. Warren Kelly won the day in his Turbo Dynamics turbocharged Blue Escort Cosworth and achieved second place in the series. But it was Fiona Kindness in her Wallace Performance prepared R32 Skyline with TD Garrett GT2860R twin turbos on board, who stormed into second place but won first place in the series. This was her third Time Attack series, but the only one in which she competed in all five rounds. To wow the crowds in between the racing, TD partners JR Motorsport showcased their Sumo Power GT Nissan GTRs competing in the FIA GT1 world championship. JRM also showcased their high performance track day and road cars.
    [Show full text]
  • DRIVER's FILE Dear Tamiya World Championship Drivers
    DRIVER'S FILE Dear Tamiya World Championship drivers, Congratulations on making it to the 2014 Tamiya World Championships here in Shizuoka, Japan. Highly skilled drivers such as yourself, from around the world are participating at this event. You have earned your right to compete here by winning one of the following championship meets: All Japan Tamiya Grand Prix (16 Regions in Japan) Hokkaido, Iwate, Miyagi, Tokyo, Nagano, Shizuoka, Kakegawa, Aichi, Toyama, Fukui, Kansai, Okayama, Sanin, Yamaguchi, Shikoku, and Kyushu. Tamiya Championship Series (2 countries from North America) Canada & United States Tamiya Asia Cup (8 countries from Asia) South Korea, Hong Kong, Taiwan, The Philippines, Thailand, Singapore, Malaysia, and Indonesia. We hope that the Tamiya World Championship 2014 will be a memorable experience for you regardless of the race result. While doing your best to promote good sportsmanship, please enjoy the event and your time here in Shizuoka. Please take the time to read this driver’s file as it contains information about the event schedule and race regulations. Also, please bring your driver’s file to the race venue and on competition days as a reference. Finally, please note that transportation to and from the venue will be provided for international drivers. ■ SECTION INDEX Page 2 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・ Championship Schedule 5 ・・・・・・・・・・・・・・・ ・ ・ ・ ・ ・・・・ ・・・・ Practice Day, Control Tires 6 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・Race Procedures 7 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・Motor Checking 8 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・Regulations 11 ・・・・・・・・・・・・・・・・・・・・・・・ Car Number Stickers, Assistants 13 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・Course Layout 14 ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・Example Settings 伪 Please note that this event will be photographed and filmed to be introduced through advertising media such as printed publications and Tamiya's Homepage. Also, race scenes will be broadcasted via USTREAM (Live video streaming).
    [Show full text]
  • USGT Class Rules and Specifications As of 5-9-2021
    USGT Class Rules and Specifications as of 5-9-2021 Chassis Specification: Any 1/10 4wd or Fwd sedan with 4 wheel independent suspension Weight Specification: 4wd Minimum 1350g in race-ready trim Fwd no minimum weight Ride Height Specification: Minimum ride height is 5mm on Carpet Tire & Wheel Specifications: Tires- Note: JANUARY 1 2014 The Ride spec tire will become the official spec tire for USGT RIE24025 - set of 4 available through Gravity RC http://www.teamgravityrc.com/ to dealers and retail Tires- RIE24025 - set of 4 available through Gravity RC http://www.teamgravityrc.com/ to dealers and retail Grinding of tire tread is NOT permitted. Sanding of mold seam to remove seam is allowed MUST USE INCLUDED INSERTS Wheels- Any 24mm - 26mm spoke (non-dish) type wheel Motor Specifications: The only legal motor for USGT will be the USGT Spec motor #GRC2000 USGT SPEC MOTOR RULES GRAVITYRC #GRC2000: NO rotors, sensors or stators outside of the below specification provided will be considered legal. Aluminum or stainless steel main can or end bell screws are prohibited for USGT competition. MOTOR TECH CHECKLIST: MEASUREMENTS TAKEN AT ROOM TEMPERATURE OF 75DEG F* AVERAGE STATOR POLE RESISTANCE: (TOLERANCE 30.0--30.7 ohms) AVERAGE TIMING AT 5,000RPM: (TOLERANCE 30--33deg) TOTAL SENSOR GAP: (TOLERANCE 0--3deg) ROTOR ALIGNMENT: (TOLERANCE 0--5deg) (These measurements were developed by Gravity RC with their in house test equipment. For assistance with motor technical inspection for your race or club track, contact Gravity RC at [email protected] ) ROTOR: Must use stock rotor - USGT logo engraved on shaft Approved ESCs: ANY ESC that is ROAR approved and using ROAR approved “Blinky” spec software or on the USVTA list Battery Specifications: Any 7.4v - 7.6v 2s ROAR approved hard case batteries.
    [Show full text]
  • Press Release
    Contact: [email protected] For Immediate Release Website: www.jdmoption.com Limited‐Edition Japanese Magazine About R35 GT‐R Now Available in English for GT‐R Fans Worldwide D’s Club, Inc. is pleased to announce the release of the English edition of the “R35 GT‐R Complete File” e‐magazine. Translated from the original Japanese‐language, limited‐ edition print magazine published earlier this year, the R35 GT‐R Complete File is dedicated exclusively to the Nissan R35 GT‐R and is the most comprehensive of its kind. Now, through our e‐publishing partner, Zinio, it’s available in English as an e‐magazine for PC’s, Macs and the iPad to GT‐R fans worldwide. Direct Link: http://www.jdmop.com/GTR/gtr‐r35.html The R35 GT‐R Complete File was created by the same editors who produce Option magazine in Japan. Option magazine was the first to chronicle the Japanese tuning industry and is considered the authority on the topic. The R35 GT‐R Complete File was originally published in Japan as a “mook,” a fusion of a magazine and a book that’s printed on high‐quality paper and produced in limited quantities. It includes articles about the latest updates to the 2012 model, including design philosophy from its chief engineer, Kazutoshi Mizuno. There are also reviews by Japan’s most‐respected automotive journalists as well as track testing of highly‐tuned GT‐Rs on Fuji Speedway and Suzuka by one of Japan’s most famous racers, Eiji “Tarzan” Yamada. Also included are tuning programs by Japan’s most‐renowned tuners, such as HKS, Mine’s, Top Secret, Jun Auto, Garage Saurus, Phoenix’s Power, Kansai Service, Powerhouse Amuse and many others.
    [Show full text]
  • Fiainmotion Issue 10
    BUILDING FOR THE FUTURE How Jean Todt and his team are working to strengthen the FIA FIAINMOTION ISSUE 10 distributed in 132 countries around the world FIA COMMENT FIA President’s A IN THIS ISSUE E S L S I O B C O I A T M I O O N T O U F A FIA NEWS BANGLADESH 4-7 Keeping up with the President... MESSAGE 8-9 Keeping up with the President...in pictures 10-11 A gathering of the clans 12-13 The FIA at the Mondial de l’Automobile CLUB NEWS 14 Poland included in Road Safety Atlas 15 How to win a rally without driving too fast 15 Too old for a driving licence? 16 Busy times in Region IV 16 Progress through competition 17 Making roads safer in rugged New Zealand 18 Road safety and fuel usage 18 ELF plays key role in Portuguese karting 18 A decade of positive discussion 19 EuroTAP pushes for progress 19 Romania makes cars green 20 Consumer protection from ADAC 21 Ambition in the islands 21 The streets of Barcelona 22-23 FIA Staff Profile: Alexandre Gueschir, FIA Marketing Director 24-27 Leadership Lines: Graham Stoker - FIA Deputy President for Sport SPORT FEATURE Eighteen months ago in our election agenda my team and I set out the policy goals that we 28-29 Formula One stewarding –a major success felt were right for the FIA, in order to enhance its role as the world’s leading independent organization promoting mobility and motor sport. We said that we would pursue these SPECIAL REPORT sport: FIA WORLD CHAMPIONSHIPS goals using innovation, excellence and teamwork and you strongly supported our plans 32-33 The FIA Formula One World Championship at the election.
    [Show full text]
  • Fenner Auto Belts
    FENNER AUTO BELTS FENNER APPLICATION OE PART NO BELT TYPE PART NO WRAPPED BELTS SEGMENT MOPEDS / 3 WHEELERS FE240 Bajaj Tempo, Hanseat 3 Wheeler / 46-1-1 FE322 TVS 50 (OE Part No. 408045) FE512 Bajaj Tempo Three Wheeler FE522 Bajaj Tempo-Hanseat 3 Wheeler (1983 on) FG309 Suvega / M651-115 (Moped) CARS/JEEPS/LCVs WFA349 Hindustan Ambassador (OE Part No.H 300 3500) WFA355 Hindustan Ambassador & Trekker (OE Part No.H 300 3500) WFA374 Fiat/Premier 1100D-Select (1960-61) WFA379 Fiat/Premier 1100D-Select (1961-64),1964 Sep.on 1100 D Delight, 1973 President, Deluxe WFA401 Premier PresidentFan & Alternator Drive Bajaj Tempo Viking 4 Wheeler (1966 on), Matador 4 Wheeler WFA411 Willys/M&M (1954-1957) Chasis 6-226-4WD 1 1/2 Tonne Fan and Generator, ACE, Eagle 6226 Station Wagon Delivery Sedan, Chassis FC 170/6 Fan & Generator Saloon 8 and 10 H.P. (1948-60), Companion / Estate Car (1954-59) WFA430 Standard Herald with Lucas TVS Dynamo (1954-59) Gazel (1973 on) WFA603 Dodge Coronet WFE426 Mahindra Van TAFE S4 Engine FE272 Willys / M&M, FC150 Truck (L.H.D) Water Pump FE372 Bajaj Tempo Matador 1400- Water Pump (1952-56) (OE Part No. 214-1-11) FE282 Willys / M&M, FC-150 Truck (R.H.D) Water Pump FE392 Bajaj Tempo Matador (OE Part No. 016-002-013) FK428 Willys/M&M-CJ 2A (1946-48)/ Station Wagon (1947)/ Station Wagon 4-63, 4 Cylinder (1948-52), Civilian Jeep (1953-63) (OE Part No. 647630) FK588 Austin Western GMC 4080 Motor Fan, GMG 4/71 Motor Fan FK628 Vauxhall, 7.5 T-Fan / Allis Chalmers, Fan & Generator / 033138 FN398 Standard 20 (OE Part No.
    [Show full text]
  • KAROSSERIELISTE Klassen EGTWHO Und EGTWFUN
    KAROSSERIELISTE Klassen EGTWHO und EGTWFUN Hersteller Original Hersteller und Bestellnummer Typ Hersteller Original Hersteller und Bestellnummer Typ Acura Reely 237989 Audi RS4 HPI 7475 Acura RSX Reely 237993 Audi R8 LMS Reely 237987 Audi A4 Dtm 2008 Alfa Romeo Reely 7105002 Audi A4 DTM 2007 Killerbody KB48555 Alfa Romeo SZ Reely 210113P2 Audi R8 Killerbody KB48559 Alfa Romeo Giulietta (2010) Reely 237991 Audi RS6 Killerbody KB48551 Alfa Romeo Trippo 33 Stradale Reely 1081975 Audi RS5 DTM Killerbody KB48318 Alfa Romeo 2000 GTAm TBG A TYPE QUATTRO RALLY Audi Quattro Killerbody KB48296 Alfa Romeo TZ3 Corsa TBG A TYPE S1 V2 Pikes Peak Audi S1 Quattro Killerbody KB48472 Alfa Romeo 155 GTA Carson 500013730 Audi Quattro Killerbody KB48481 Alfa Romeo 75 Turbo Evo HPI 7405 Audi A4 Avant HPI 17544 Alfa Romeo 8C Rc-expert.com C402 Audi Quattro V8 HPI 7411 Alfa Romeo 156 Aplastics RS2 Audi RS2 HPI 7439 Alfa Romeo GTV Carisma 15374 Audi RS5 DTM Tamiya 51555 Alfa Romeo 155 V6 Delta Plastik 0023 Audi A3 Tamiya 58606 Alfa Romeo 155 V6 Ti Martini Delta Plastik 0041 Audi Avus Tamiya 51615 Audi Quattro Rally A2 The Rally Legends EZRL2424 Audi Quattro SR 1985 Tamiya 51555 Alfa Romeo 155 V6 Ti Jägerm. Exotek 1863 Audi R8 LMS Delta Plastik 0022 Alfa Romeo GTV Delta Plastik FT002 Alfa Romeo 8C Bentley Delta Plastik FT019 Alfa Romeo Mito Kamtec 174 Bentley Continental COLT M2311 Alfa Romeo Giulia GTA Mon-Tech MB019-007 AlfaRomeo Mito Bugatti Matrixline PC201406 Bugatti Veyron Chevron ZTC001RE Bugatti EB110 Aston Martin Kyosho FAB010 Aston Martin DBR09 BMW Matrixline
    [Show full text]
  • Vertical Facility List
    Facility List The Walt Disney Company is committed to fostering safe, inclusive and respectful workplaces wherever Disney-branded products are manufactured. Numerous measures in support of this commitment are in place, including increased transparency. To that end, we have published this list of the roughly 7,600 facilities in over 70 countries that manufacture Disney-branded products sold, distributed or used in our own retail businesses such as The Disney Stores and Theme Parks, as well as those used in our internal operations. Our goal in releasing this information is to foster collaboration with industry peers, governments, non- governmental organizations and others interested in improving working conditions. Under our International Labor Standards (ILS) Program, facilities that manufacture products or components incorporating Disney intellectual properties must be declared to Disney and receive prior authorization to manufacture. The list below includes the names and addresses of facilities disclosed to us by vendors under the requirements of Disney’s ILS Program for our vertical business, which includes our own retail businesses and internal operations. The list does not include the facilities used only by licensees of The Walt Disney Company or its affiliates that source, manufacture and sell consumer products by and through independent entities. Disney’s vertical business comprises a wide range of product categories including apparel, toys, electronics, food, home goods, personal care, books and others. As a result, the number of facilities involved in the production of Disney-branded products may be larger than for companies that operate in only one or a limited number of product categories. In addition, because we require vendors to disclose any facility where Disney intellectual property is present as part of the manufacturing process, the list includes facilities that may extend beyond finished goods manufacturers or final assembly locations.
    [Show full text]