Royal Prestige® Juicer

CAREUSE AND& CARE USE MANUAL MANUAL

ROYAL PRESTIGE® JUICER

IMPORTANT: To prevent personal injury and/or property damage, read and follow the instructions and warnings in this Care and Use Manual. SAVE THESE INSTRUCTIONS • FOR QUESTIONS OR COMMENTS, SEE REVERSE FOR YOUR SERVICE CENTER CONTACT NUMBER. FOR HOUSEHOLD USE ONLY. ® 2 ROYAL PRESTIGE JUICER

Table of Contents Introduction 2 Important Safeguards 3 Product Diagram 4 Before you Start 6 Operation 8 Cleaning and Care Instructions 15 Troubleshooting/FAQ 20 Technical Information 23 Customer Service 24

READ ALL INSTRUCTIONS BEFORE USE Introduction Welcome and congratulations on purchasing your Royal Prestige® Juicer. Please be sure to read this manual in its en- tirety before using your Royal Prestige® Juicer to ensure that you have an enjoyable experience. The valuable information contained in this manual will provide an overview of the product, some helpful hints to get you started, as well as trouble-shooting tips should you have issues with this product in the future. ® ROYAL PRESTIGE 3 JUICER

The following precautions are provided to ensure the safety of the user. Please carefully read through the precautions and exercise care when using the appliance.

Warning: This label warns of the risk of death or severe injuries. Prohibited Do not disassemble

Caution: This label warns of the risk of injuries or appliance damage. Must take action Important Safeguards This appliance is for household use only. Please carefully follow the instructions in the manual. (This appliance cannot be covered under warranty if the product is abnormally or commercially used). Save the instruction manual for future reference. These instructions are also available on www.royalprestige.com. If the appliance is given away as a gift, please include the manual with the product. When using electrical appliances, basic safety precautions should be followed including the following: READ ALL INSTRUCTIONS. Risk of • Do not immerse motor base in water or other liquid. Electric Shock or Fire • The use of attachments not recommended or sold by the manufacturer may cause fire, electric shock or injury. • Do not spray water or flammable sprays near the appliance. Risk of Injury • Close supervision is necessary when any appliance is used by or near children. • Avoid contact with any moving parts. • Always make sure the feed tube is closed securely in place before motor is turned on. Do not open the feed tube while Juicer is in operation. • Turn switch to OFF position after each use of your Juicer . Make sure the motor stops completely before disassembling. • Do not put fingers or other objects into the feed tube during operation. If food becomes lodged, use pusher or another piece of fruit or vegetable to push it down. When this method does not work, turn the motor off and disassemble Juicer to remove the remaining food. • This device is not intended for use by persons (including children) whose physical, sensory or mental abilities are different or reduced, or who lack experience or knowledge, unless such persons receive supervision or training for the operation of the device by a person responsible for your safety. • Children should be supervised to ensure that they do not use the device as a toy. Dangers • Unplug from wall outlet when not in use before putting on or taking off parts, and before Related to Misuse cleaning. • Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or damaged in any manner. Return appliance to customer support for examination and/or repair. • Do not use outdoors. • Do not let cord hang over edge of table, counter, or another surface area. • Do not use the appliance if the rotation wiper is damaged. • Do not operate without the pulp cup in place. • Do not alter or modify the appliance in any way. • Do not use the appliance for anything other than its intended purpose as described in the manual. • The appliance should be used for a limited period of time to prevent overheating. • Do not use the appliance on an uneven surface. • Do not put the Juicer parts in the dishwasher or extremely hot water. • Do not use any hazardous chemicals to clean the appliance. ® 4 ROYAL PRESTIGE JUICER PARTS ** TheThe productsproducts illustratedillustrated inin thisthis bookletbooklet maymay varyvary slightlyslightly fromfrom thethe actualactual product.product. ** TheThe productsproducts illustratedillustrated inin thisthis bookletbooklet maymay varyvary slightlyslightly fromfrom thethe actualactual product.product. Product Diagram 2. Feed Tube locking mechanism PARTS 1. Feed Tube * The products illustrated in this booklet may vary slightly from the actual product. 4. Cap * The products illustrated in this booklet may vary slightly from the actual product. +

Feed Basket Feed Tube

2. Bowl 5.+ Body + + STEP 1 Top-set Assembly 3. Pulp Cup 6. Juice3. CupFeed Align the red dots ● onon eacheach partpart andand assemble in the order shown. Once + assembled, turn the drum lid clockwise to close. + STEP 1 Top-set Assembly Align the red dots ● on +each part and assemble in the order shown. Once + assembled, turn the drum lid clockwise to close. 7.7. RotationRotation Wiper Wiper 8. 8. StrainerStrainer 9.9. JuicingJuicing Screw Screw 10. Pusher + STEP 2 + Top-set and body assembly Place the drum lid on the juicing bowl. Align the down arrow ▼on the drum lid 11. 7. Rotation Wiper 8. Strainer 9. Juicing Screw 11.11.10. Cleaning PusherCleaning Brush Brush 11. 12. RotatingCepillo Rotating rotativo Brush Brush 13. 13. LidLid Opener Opener with the OPENOPEN markmark onon thethe bodybody andand turn to the CLOSECLOSE position.position. + STEP 2 + Top-set and body assembly

Place the drum lid on the juicing bowl. Align the down arrow ▼on the drum lid 11. Cleaning Brush 12. Rotating Brush 13. Lid Opener with the OPEN mark on the body and + turn to the CLOSE position. 6 7

6 7 ® PARTS ROYAL PRESTIGE 5 * The products illustrated in this booklet may vary slightly from the actual product. * JUICERThe products illustrated in this booklet may vary slightly from the actual product.

* The products illustrated/photographed in this manual may vary slightly from the actual product.

+ STEP 1 STEP 1 Top-setTop-set Assembly Assembly

AlignAlign the redthe dots red ● dots on each ● on part each and part and assembleassemble all the in pieces the inorder the order shown. shown. Once + Onceassembled, assembled, turn turn the feed drum tube lid clockwise clockwise to toclose. close.

7. Rotation Wiper 8. Strainer 9. Juicing Screw 10. Pusher + STEPSTEP 2 2 Top-set and base assembly Top-set and body assembly Assemble the entire top-set onto the base Place the drum lid on the juicing bowl. ensuring the arrow symbol ▼ on the feed Align the down arrow ▼on the drum lid 11. Cleaning Brush 12. Rotating Brush 13. Lid Opener tubewith is aligned the withOPEN the mark arrow onsymbol the body on and the base. + turn to the CLOSE position.

6 7 HOW TO ASSEMBLE

STEP 1 Top-set Assembly STEP 2 Top-set and Body Assembly

For easy assembly hold the drum lid Open/Close mark on the top-set. Check Before • Wash the parts before first use. TIP by grabbing the feeding tube and turn 5 Operating • Ensure that the silicone ring is assembled properly. clockwise as shown in the illustration.

Assemble the strainer intoROYAL the rotation PRESTIGE ®Place the juicing screw into the strainer. 6 1 wiper then place this assembly in to the 2 Turn and press down on it until it clicks into juicing bowl ensuring the red dotJUICER ● on place. the strainer is aligned with the red dot ● on the juicing bowl. Open HOW TO ASSEMBLE Before You Start Check Before Operating Wash the parts before first use. STEP 1 Top-set Assembly STEP 2 Top-set and Body Assembly

For easy assembly hold the drum lid Open/Close mark on the top-set. Check Before • Wash the parts before first use. TIP 5 Top-set Assembly by grabbing the feeding tube and turn STEP 1Operating • Ensure that the silicone ring is assembled Noteproperly. | The juicing screw needs to be locked in place in order to close the drum lid. clockwise as shown in the illustration. Close

Assemble the strainer into the rotation wiper, then Place the feed tube onto the bowl aligning the red Note | The juicer will not operate if the down arrow 1 place thisAssemble assembly the into strainer the bowl into ensuring the rotation the red dot 3Placedot the ● Placeonjuicing the the feed screw drum tube into lid with on the tothe strainer. the red juicing dot ● bowl on the bowl. ▼ on the drum lid is not completely aligned 1 wiper then place this assembly in to the 2 Turn 3and press down on it until it clicks into with the CLOSE mark on the body. ● on the strainer is aligned with the red Turn clockwisealigning theto close, red dot aligning ● on the the drum red dot lid ●with on the juicing bowl ensuring the red dot ● on place. the red dot ● on the juicing bowl. Turn dot ● on the bowl. feed tube with the close mark . the strainer is aligned with the red dot ● clockwise to close, aligning the red dot ● Place the drum lid on the juicing bowl. Place the pulp cup under the pulp on the juicing bowl. on the drum lid with the close mark . 4 Align the down arrow ▼ on the drum 6 spout and place the juice cup under the lid with the OPEN mark on the body juice spout as shown in the illustration.Open and turn to the CLOSE position.

HOW TO ASSEMBLE Note | The juicing screw needs to be locked in place in order to close the drum lid. Close

Note | The juicer will not operate if the down arrow STEP 1 Top-set Assembly PlaceSTEP the drum 2 lidTop-set on to theand juicing Body Assembly bowl ▼ on the drum lid is not completely aligned 3 aligning the red dot ● on the drum lid with with the CLOSE mark on the body. the red dotFor ● easy on the assembly juicing holdbowl. the Turn drum lid Open/Close mark on the top-set. Check Before • Wash the parts before first use. TIP 5 clockwise byto grabbingclose, aligning the feeding the red tube dot ● and turn Place the drum lid on the juicing bowl. Place the pulp cup under the pulp Operating • Ensure that the silicone ring is assembled properly. on the drumclockwise lid with as the shown close in mark the illustration. . 4 Align the down arrow ▼ on the drum 6 spout and place the juice cup under the lid with the OPEN mark on the body juice spout as shown in the illustration. 8 and turn to the CLOSE position. 9 Assemble the strainer into the rotation Place thePlace screw the juicinginto the screw strainer. into Turn the and strainer. press down 1 wiper then place this assembly in to the 2 Turn and press down on it until it clicks into juicing bowl ensuring the red dot ● on 2 on it untilplace. it clicks into place. the strainer is aligned with the red dot ● on the juicing bowl. Open

Note | The juicing screw needs to be locked in place in order to close the drum lid. Close Note: The screw needs to be locked in place in order to close the feed tube. Note | The juicer will not operate if the down arrow 8 Place the drum lid on to the juicing bowl ▼ on the drum lid is not completely aligned 9 3 aligning the red dot ● on the drum lid with with the CLOSE mark on the body. the red dot ● on the juicing bowl. Turn clockwise to close, aligning the red dot ● Place the drum lid on the juicing bowl. Place the pulp cup under the pulp on the drum lid with the close mark . 4 Align the down arrow ▼ on the drum 6 spout and place the juice cup under the lid with the OPEN mark on the body juice spout as shown in the illustration. and turn to the CLOSE position.

8 9 HOW TO ASSEMBLE

STEP 1 Top-set Assembly STEP 2 Top-set and Body Assembly

Assemble the strainer into the rotation Place the juicing screw into the strainer. 1 wiper then place this assembly in to the 2 Turn and press down on it until it clicks into juicing bowl ensuring the red dot ● on place. the strainer is aligned with the red dot ● on the juicing bowl. Open

® HOW TO ASSEMBLE ROYAL PRESTIGE 7 Note | The juicing screw needs to be locked in JUICER place in order to close the drum lid. Close STEP 1 Top-set Assembly STEP 2 Top-set and Body Assembly HOW TO ASSEMBLE Note | The juicer will not operate if the down arrow ▼ on the drum lid is not completely aligned Place the drumFor lid easy on assembly to the juicing hold bowlthe drum lid Open/Close mark on the top-set. 3 Top-set and Base Assembly with the CLOSE mark on the body. Check Before • Wash the parts before first use. aligningSTEPTIP the 2 byred grabbing dot ● on the the feeding drum lid tube with and turn 5 STEP 1 Top-set Assembly Operating • Ensure that the silicone ring is assembledSTEP properly. 2 Top-set and Body Assembly the red dot ●clockwise on the juicing as shown bowl. in Turnthe illustration. clockwise to close, aligning the red dot ● Open/Close mark on the top-set. PlacePlace the the top-set drum onlid topon theof the juicing base. bowl. Align the 6 Place the pulp cup under the pulp For easy assembly hold the drum lid on4 the drumOpen/Close lid with markthe close on the mark top-set. . 54 Align the down arrow ▼ on the drum spout and place the juice cup under the TIP 5 arrow ▼ on the feed tube with the arrow Check Before • Wash the parts before first use. 1 Assemble the strainer into the rotation 2 Place theby juicing grabbing screw the into feeding the strainer. tube and turn lid with the OPEN mark on the body juice spout as shown in the illustration. Operating • Ensure that the silicone ring is assembled wiperproperly. then place this assembly in to the Turn andclockwise press down as shownon it until in itthe clicks illustration. into (open)and turn on the to thebase. CLOSE position. juicing bowl ensuring the red dot ● on place. the strainer is aligned with the red dot ● Assemble the strainer into the rotation Placeon thethe juicingjuicing screwbowl. into the strainer. 1 wiper then place this assembly in to the 2 Turn and press down on it until it clicks into Open juicing bowl ensuring the red dot ● on place. the strainer is aligned with the red dot ● on the juicing bowl. Open

Note | The juicing screw needs to be locked in place in order to close the drum lid. Close

Note | The juicer will not operate if the down arrow Place the drum lid on to the juicing bowl ▼ on the drum lid is not completely aligned NoteHOW | The juicing TO screwASSEMBLE needs to be locked in with the CLOSE mark on the body. place in order to close the drum lid. 3 aligning the red dot ● on the drum lid with Close 8 the red dot ● on the juicing bowl. Turn Place the pulp cup under the pulp spout and 9 clockwise to close, aligning the red dot ● Note | ThePlace juicer the will drum not operate lid on ifthe the juicing down arrowbowl. 6 placePlace the the juice pulp cup cup under under the the juice pulp spout as Note: The▼ onJuicer the drumwill not lid operate is not completely if parts are aligned not STEPPlace 1the drumTop-set lid Assembly on to the juicing bowl on the drum lid with the close mark . STEP4 2 Top-set and Body Assembly 6 3 assembledwithAlign properly. the the CLOSE down mark arrow on the ▼ onbody. the drum shownspout in and the placeillustration. the juice Pusher cup is under optional. the aligning the red dot ● on the drum lid with lid with the OPEN mark on the body juice spout as shown in the illustration. the red dot ● on the juicing bowl. Turn ForFor andeasy easy turnassembly assembly to the hold hold CLOSE the thefeed position. drum tube lidwith Open/Close mark on the top-set. Checkclockwise Before to close,• Wash aligning the parts the red before dot ●first use. TIP Operating Place the drum lid on the juicing bowl. TIP bothPlaceby handsgrabbing the pulp and thecupturn feeding underclockwise the tube aspulp andshown turn 5 on the drum lid •with Ensure the that close the mark silicone . ring is assembled properly.4 6 Align the down arrow ▼ on the drum inspout clockwisethe illustration. and place as shown the juice in the cup illustration. under the lid with the OPEN mark on the body juice spout as shown in the illustration. and turn to the CLOSE position. 1 Assemble the strainer into the rotation Place the juicing screw into the strainer. wiper then place this assembly in to the 2 Turn and press down on it until it clicks into juicing bowl ensuring the red dot ● on place. the strainer is aligned with the red dot ● on the juicing bowl. Open

8 Note | The juicing screw needs to be locked in 9 place in order to close the drum lid. Close Note | The juicer will not operate if the down arrow 8 Place the drum lid on to the juicing bowl 9 ▼ on the drum lid is not completely aligned 3 aligning the red dot ● on the drum lid with with the CLOSE mark on the body. the red dot ● on the juicing bowl. Turn clockwise to close, aligning the red dot ● Place the drum lid on the juicing bowl. Place the pulp cup under the pulp on the drum lid with the close mark . 4 Align the down arrow ▼ on the drum 6 spout and place the juice cup under the lid with the OPEN mark on the body juice spout as shown in the illustration. and turn to the CLOSE position.

8 9 ® 8 ROYAL PRESTIGE JUICER

Operation STEP 1 After preparing the ingredients, plug the power cord into a wall outlet. Note: • Do not touch the power cord with wet hands. It may cause electrical shock, short-circuit, or fire. • Check the safety of the wall outlet. STEP 2 Press the FORWARD button to operate. Note: • Forward: Pulls down and slowly presses the ingredients. • Reverse: Pushes the ingredients back up to dislodge them. If the ingredients become jammed in the screw and the feed tube does not open, press the OFF button. Then press and hold the REVERSE button until the ingredients become dislodged. Repeat REVERSE - OFF - FORWARD as often as needed to achieve the desired result.

If the Juicer stops during operation

Switch the button to OFF position then press and hold the FORWARD : Pulls down the food REVERSE button until the ingredients become dislodged. OFF : Stops the operation Repeat REVERSE - OFF - FORWARD as needed. REVERSE : Pushes the food back up

➊ ➋ ➌ ➍ ▲ ▲ ▲ OFF REVERSE OFF FORWARD

Note | REVERSE: Pushes the ingredients back up to dislodge them. The REVERSE button only works while holding down the switch.

Switch OFF ensuring that the Juicer comes to a complete stop. Then press REVERSE. Hold the REVERSE button for 2-3 seconds and release. Repeat as needed. Let the Juicer stop completely before using the REVERSE button to prevent malfunction.

If the Juicer does not work after these steps, disassemble and clean the parts before operating the Juicer again. ® ROYAL PRESTIGE 9 JUICER

STEP 3 Insert the prepared ingredients one piece at a time.

Note: • Prepare ingredients for optimal extraction. • If a large quantity of ingredients is put into the feed tube, it can cause the Juicer to stop. • Insert the ingredients one piece at a time. • Remove hard seeds or pits in fruits. When juicing frozen fruits, completely thaw before juicing.

Hard vegetables & high fiber foods | (E.g. carrots, beets, & spinach) Tip: Insert • Tough and fibrous ingredients: Cut to size. into the feed tube • Fibrous leafy vegetables (celery, kale, collard greens, etc.): Cut the stems to size.

Insert Soft Fruits & Vegetables | (E.g. apples, oranges & tomatoes) Tip: into the • Soft ingredients: Cut ingredients to size. Insert the prepared ingredients into the feed feed basket and push down the ingredient with the basket lid to extract. basket

STEP 4 Use the cap to make mixed juices, stop juice from dripping, or rinse between different juices.

Capcap

Tip: • Juicing with the cap closed makes various mixed juice creations when different fruits and vegetables, milk, banana, beans etc. are selected. • After juicing, close the cap to stop the juice from dripping, especially when disassembling the bowl off the base. • When making different juices quickly rinse away any leftover flavors by running a glass of water in the Juicer with the cap closed.

Note : • Leave the cap open when juicing ingredients that create excessive foam during extraction, (e.g. apples, celery). • Pay close attention when operating with the cap closed. Juice may overflow if the juice collected in the bowl exceeds its capacity marked on the bowl.

STEP 5 After juice and pulp are completely extracted, switch the unit OFF. Note: • If the remaining ingredients in the bowl have not been extracted completely, the feed tube may not open easily. After each extraction, run the Juicer for an additional 30 seconds to let it extract the remaining pulp. • When the feed tube is stuck, press the REVERSE - OFF - FORWARD button in this order; switching back and forth 2 or 3 times to dislodge the ingredients. Then place hands on top of the feed tube’s lid and firmly press down, while simultaneously turning it counter clockwise to open. » Depending on the ingredients, pour water down the feed tube to rinse out the interior of the bowl and then attempt to remove it. ® 10 ROYAL PRESTIGE JUICER

Helpful Hints 1. Operating the Juicer without ingredients can cause damage to the juicing screw. 2. Do not continuously operate the Juicer for more than 30 minutes. This can overheat the motor and damage it. After continuous use, let the Juicer rest for 30 minutes to cool down before starting another session. 3. Do not put fingers or other objects into the feed tube. Always use provided pusher when needed. If other objects are inserted into the feed tube during operation, they can get stuck and damage the Juicer parts and/ or cause injury. 4. Do not put dried or hard ingredients like whole grains, fruits with hard seeds or ice into the Juicer. These may damage the parts (e.g. bowl, juicing screw, and strainer). • Beans or grains can be used if soaked overnight or boiled. • Fruits with pits and hard seeds must be pitted before juicing (e.g. nectarines, peaches, mangoes and cherries). • When using frozen fruits with small seeds such as grapes, completely thaw before inserting them into the Juicer . 5. Do not use ingredients containing excessive amounts of vegetable oil or animal fat. Do not use the Juicer to extract vegetable oil from ingredients. If vegetable/animal oil gets on the screw, it may reduce performance and even damage the part. 6. Do not reinsert the extracted pulp into the Juicer . This can cause the unit to stop or cause the feed tube not to open. 7. After juicing ingredients with seeds like grapes, thoroughly clean all the crevices on the bottom of the screw. Juicer damaged due to owner negligence or from not following the instructions in this manual will void the warranty.

DO NOT put the following ingredients into the Juicer: Hard seeds Peach, nectarines, apricot, plum, mango, etc. Remove hard seeds or pits from the ingredients before juicing

Hard or inedible skins Pineapple, melon, mango, orange, etc. Peel the skin from the ingredients before juicing.

Frozen fruits or ice Frozen strawberry, blueberry, raspberry, etc. Completely thaw frozen fruits before juicing. Do not use ice. ® ROYAL PRESTIGE 11 JUICER

Vegetable/animal oil Sesame seed, butter, margarine, etc. Do not extract ingredients containing vegetable or animal oil. This can reduce performance and even damage the Juicer .

Others Coconut, sugarcane, whole grains, etc. Do not extract ingredients with no water content.

Experience the best quality juice by understanding each ingredient’s characteristics and knowing the optimal way of handling them. The Juicer is an innovative product that uses a patented slow-speed juicing technology to efficiently extract the juice from ingredients. The Juicer is designed to obtain the best result from ingredients with firm composition and with high water content. For best result, each ingredient should be prepared and extracted depending on its characteristics and properties. Tips On Ingredients Before Operating • Before Operating: If the Juicer is jammed or if the feed tube does not open, press the REVERSE button and hold until the ingredient becomes dislodged. Repeat REVERSE-OFF-FORWARD as needed. • Continue operating the Juicer until all the ingredients in the bowl are extracted. The feed tube may not open easily if there is a lot of pulp remaining in the Juicer . • Every ingredient yields different amounts of juice.

Juice Yield • For the optimal extraction and maximum juice yield, cut the ingredients following the guidelines given in this section. • Insert ingredients slowly, monitoring how they are extracted. The juice yield may vary depending on the juicing speed.

Adjusting • Depending on the ingredient, you may get extra pulp when juicing continuously. the Amount • To reduce the amount of pulp, disassemble the top-set and wash frequently. of Pulp in the Juice ® 12 ROYAL PRESTIGE JUICER

SOFT FRUITS AND VEGETABLES (e.g. oranges, tomatoes):

• Peel the skin off oranges, and for tomatoes and apples, take out the stem. • If the ingredients are larger than the feed tube, cut the ingredients into pieces that will fit into it. • Fruits with seeds must be pitted before extraction. Cut to size then slowly insert them down the feed tube.

PREPARATION TIPS: • Cut ingredients cut to size. EXTRACTION TIPS: • Slowly insert the ingredients, one piece at a time. • Use the pusher to push the ingredients down the feed tube. (The pusher also helps prevent juice from spraying out of the feed tube when extracting ingredients with high water content) • Leave the cap open when juicing ingredients that create excessive foam during extraction, like apples and celery. (Foam can accumulate if operated with the cap closed). • It is recommended that the extracted juice be consumed within 48 hours after extracting. Depending on the density of the ingredients, the extracted juice can gradually separate into layers over time. • If there is an excessive amount of foam, use a mesh strainer to separate it from the juice. • When an ingredient is being juiced by the screw, the squeezed ingredient may splash juice through the feed tube. Use the pusher to block splashing while juicing.

HARD FRUITS AND VEGETABLES (e.g. carrots, potatoes, beets):

• Hard fruits and vegetables may put excess strain onto the motor and cause it to stall. • To increase the juice yield, juice fruits and vegetables with high water content.

PREPARATION TIPS: • Slice the ingredients cut to size ® ROYAL PRESTIGE 13 JUICER

EXTRACTION TIPS: • Slowly insert the ingredients, one at a time. • Pace the juicing speed, ensuring each ingredient is thoroughly extracted. • To maximize the juice yield, juice ingredients with high water content.

INGREDIENTS WITH SMALL SEEDS (e.g. raspberry, pomegranate, grape): Slowly insert ingredients with small seeds to prevent clogging the Strainer.

• Insert ingredients slowly to minimize the amount of leftover seeds in the Strainer. • For best results, use ingredients with a higher amount of fluid (e.g. apple, pear).

PREPARATION TIPS: • When juicing frozen ingredients, make sure they are completely thawed (e.g. raspberry, strawberry). • Rinse ingredients thoroughly. Remove all stems. • For pomegranate, discard the skin and juice only the inner part. EXTRACTION TIPS: • Depending on the size of the grape, insert 3-5 grapes at a time while monitoring the extraction result. • For ingredients like pomegranate and raspberry, insert about 1 tablespoon (5g) at a time. • Frozen ingredients usually lose a significant amount of fluid from thawing. When juicing, mix milk or yogurt to balance the fluid lost.

CAUTION: If the feed tube does not open due to excessive amount of small seeds left in the bowl, continuously run the Juicer for 30 seconds to extract any leftover seeds. If the feed tube is still stuck, repeat REVERSE - OFF- FORWARD until the ingredients become dislodged. Then twist the feed tube to open while pushing downwards with palms. (Depending on the ingredient, pour some water down the feed tube for a quick rinse to help dislodge). ® 14 ROYAL PRESTIGE JUICER

FIBROUS AND/OR TOUGH LEAFY INGREDIENTS (e.g. celery, kale, pineapple): Fibrous ingredients like celery and kale should be cut to size.

• When juicing leafy ingredients like celery and kale, do not collect more than 500g (approximately 2¼ cups) per session. For best results, disassemble and wash the top-set before juicing again. • If leafy ingredients wrap around the screw, open the feed tube and remove the fibers before continuing to juice. • It’s best to use ingredients with a higher amount of fluid, like apples or carrots.

PREPARATION TIPS: • Separate each stem. Cut outer stems to size. EXTRACTION TIPS: • Slowly insert the prepared ingredients one at a time. • Insert more ingredients after the previous ones have been completely extracted.

■■ Roll leaves in spiral before inserting into the Juicer .

■■ Insert the leafy part of the ingredients first, then alternate between leafy parts and stems.

■■ For ingredients like cilantro or wheatgrass, grab a handful and insert in a bundle.

CAUTION: • The fibers from tough ingredients like celery can wrap around the juicing screw and affect the Juicer ’s performance. Cut the stems to size. • Foam can build up from juicing fibrous ingredients. Use strainer to remove the foam before serving. • For ingredients like pineapple, slice off the rind of the pineapple and cut around the fibrous core. Cut the flesh of the pineapple to smaller pieces. • Recommended amount of juicing per session is 500g (approximately 2¼ cups). When juicing more than this amount, wash the top-set before continuing to juice. HOW TO DISASSEMBLE AND CLEAN * The products illustrated in this booklet may vary slightly from the actual product.

1 Switch OFF and unplug the power cord 4 Remove the juicing screw, strainer and 6 Under running water, clean the outside Quick Rinsing from the wall outlet. rotation wiper unit from the juicing bowl. of the juicing screw with a dish scrub. Use Clean with provided brush. the tip of the cleaning brush to push out Note | · Extract all the remaining pulp in the With the smart cap closed, fill the juicing juicing bowl before stopping the juicer. any residue in the crevices on the bottom 1 bowl with water and turn on the juicer. · For easier clean up, operate the juicer for of the juicing screw. an additional 30 seconds after the juice is extracted. · When the drum lid is stuck, press the REVERSE – OFF – FORWARD button in this order, switching back and forth 2 to 3 times to dislodge. Then place both hands on the drum lid and firmly press down while ® simultaneously turning the drum lid to open. ROYAL PRESTIGE 15 * Fill the juicing bowl with water and run JUICER the juicer before opening the drum lid. It may help to open the drum lid when stuck. Note | Immediately clean the juicer after each HOW TO DISASSEMBLE AND CLEAN use. If remaining residue in the juicer dries Turn the drum lid counter clockwise to up, it can make disassembling and clean- Tip | Thoroughly clean the juicing screw 2 up difficult. The excess build up can cause * The products illustrated in this booklet may vary slightly from the actual product. open. ensuring that the juicing screw is clean Cleaning and Care poor performance in future uses. without any residue. Remove the juicing screw, strainer and For easier disassembly, place the top- 1 Switch OFF and unplug the power cord 4 6 Under running water, clean the outside Quick RinsingCompletely dry before using. from the wall outlet. rotation wiper unit from the juicing bowl. of theset juicing in the sink screw and with run thea dish water scrub. through Use Note | After juicing ingredients with seeds, make Let it run for a moment. Open the NOTE: Clean with provided brush. from the top of the top-set. Note | · Extract all the remaining pulp in the the tip of the cleaning brush to push out sure to thoroughly clean the bottom 2 Thoroughly dry the bottom of the juicing With the smart cap closed, fill the juicing smart cap and let the water run out of Extract all thejuicing remaining bowl before pulp stopping in the the bowl juicer. before stopping the Juicer . any residue in the crevices on the bottom crevice of the juicing screw. (If this area screw. 1 bowl with water and turn on the juicer. the juicing bowl. · For easier clean up, operate the juicer for of the juicing screw. isn’t properly cleaned, it can cause the For easier cleanan additional up, operate 30 seconds the after Juicer the juice for is an additional 30 seconds after the juice part to be damaged.) is extracted.extracted. · When the drum lid is stuck, press the Place the juicing bowl under running 5 water. When the feedREVERSE tube –is OFF stuck, – FORWARD press the button REVERSE in this – OFF – FORWARD button in this order, switching back 7 Clean the body with a soft damp towel and forth 2 toorder, 3 times switching to dislodgeback and .forth Then 2 toplace 3 times hands on the lower part of the feed tube and firmly press down and dry. to dislodge. Then place both hands on Note | When moving the appliance, do not lift simultaneouslythe turningdrum lid the and feed firmly tube press counter down while clockwise to open. by grabbing the feeding tube. Always lift simultaneously turning the drum lid to open. the appliance by grabbing the body or handle. * Fill the juicing bowl with water and run Switch OFFthe and juicer unplug before the openingpower cord the drumfrom lid. It Lift top set vertically off base. may help to open the drum lid when stuck. Turn the top-set counter clockwise and 1 the wall outlet. 3 Note | Immediately3 lift off cleanthe body.the juicer after each Turn the feed tube counter clockwise to open. use. If remaining residue in the juicer dries Turn the drum lid counter clockwise to up, it can make disassembling and clean- 2 Tip | Thoroughly clean the juicing screw 2 up difficult. The excess build up can cause open. ensuring that the juicing screw is clean poor performance in future uses. Tip | It is not necessary to completely clean without any residue. the juicer in between making multiple For easier disassembly, place the top- Completely dry before using. juices during a single juicing session. set in the sink and run the water through from the top of the top-set. NoteTIP | AfterThe round juicing brush ingredients can clean with the seeds, juice make Let it run for a moment. Open the When finished with juicing, always surespout to ofthoroughly the juicing clean bowl. the bottom 2 disassemble and clean thoroughly Thoroughly dry the bottom of the juicing smart cap and let the water run out of crevice of the juicing screw. (If this area between juicing sessions to prevent screw. the juicingNote | bowl.If the towel is dripping wet, make sure isn’t properly cleaned, it can cause the to squeeze out the excess liquid before residue buildup. part to be damaged.) using it on the juicer. Place the juicing bowl under running 5 18 19 HOW TO DISASSEMBLE AND CLEANwater. Clean the body with a soft damp towel 7 and dry. Note | When moving the appliance, do not lift * The products illustrated in this booklet may vary slightly from the actual product. by grabbing the feeding tube. Always lift Remove the juicing screw, strainer and rotation wiper unit the appliance by grabbing the body or 4 handle.1 Switch OFF and unplug the power cord from4 theRemove bowl. Clean the withjuicing provided screw, brush. strainer and 6 Under running water, clean the outside Quick Rinsing NOTE: from the wall outlet. rotation wiper unit from the juicing bowl. of the juicing screw with a dish scrub. Use When movingTurn the thetop-set appliance, counter clockwise do not andlift Clean with provided brush. the tip of the cleaning brush to push out Note | · Extract all the remaining pulp in the With the smart cap closed, fill the juicing 3 lift off the body.juicing bowl before stopping the juicer. any residue in the crevices on the bottom by grabbing the feed tube. Always lift the 1 bowl with water and turn on the juicer. appliance by grabbing· For easier the clean base up, oroperate handle. the juicer for of the juicing screw. an additional 30 seconds after the juice is extracted. Tip | It is not necessary to completely clean · When the drum lid is stuck, press the the juicer in between making multiple REVERSE – OFF – FORWARD button in this juices during a single juicing session. order, switching back and forth 2 to 3 times TIP | The round brush can clean the juice When finished with juicing, always to dislodge. Then place both hands on spout of the juicing bowl. disassemble and clean thoroughly the drum lid and firmly press down while between juicing sessions to prevent simultaneously turning the drum lid to open. Note | If the towel is dripping wet, make sure to squeeze out the excess liquid before residue buildup. * Fill the juicing bowl with water and run using it on the juicer. the juicer before opening the drum lid. It may help to open the drum lid when stuck. 18 Note | Immediately clean the juicer after each 19 use. If remaining residue in the juicer dries Turn the drum lid counter clockwise to up, it can make disassembling and clean- Tip | Thoroughly clean the juicing screw 2 up difficult. The excess build up can cause open. ensuring that the juicing screw is clean poor performance in future uses. without any residue. For easier disassembly, place the top- Completely dry before using. set in the sink and run the water through from the top of the top-set. Note | After juicing ingredients with seeds, make Let it run for a moment. Open the sure to thoroughly clean the bottom 2 Thoroughly dry the bottom of the juicing smart cap and let the water run out of crevice of the juicing screw. (If this area screw. the juicing bowl. isn’t properly cleaned, it can cause the part to be damaged.)

5 Place the juicing bowl under running water. Clean the body with a soft damp towel 7 and dry. Note | When moving the appliance, do not lift by grabbing the feeding tube. Always lift the appliance by grabbing the body or handle.

Turn the top-set counter clockwise and 3 lift off the body.

Tip | It is not necessary to completely clean the juicer in between making multiple juices during a single juicing session. TIP | The round brush can clean the juice When finished with juicing, always spout of the juicing bowl. disassemble and clean thoroughly Note | If the towel is dripping wet, make sure between juicing sessions to prevent to squeeze out the excess liquid before residue buildup. using it on the juicer.

18 19 ® 16 ROYAL PRESTIGE HOW TO DISASSEMBLE AND CLEAN JUICER * The products illustrated in this booklet may vary slightly from the actual product.

1 Switch OFF and unplug the power cord 4 Remove the juicing screw, strainer and 6 Under running water, clean the outside Quick Rinsing from the wall outlet. rotation wiper unit from the juicing bowl. Under runningof the juicing water, cleanscrew the with outside a dish of scrub. the screw Use with Clean with provided brush. 5 a dish scrub.the tip Use of thethe cleaningtip of a cleaning brush totool push to push out out any Note | · Extract all the remaining pulp in the NOTE: With the smart cap closed, fill the juicing juicing bowl before stopping the juicer. residueany in the residue crevices in theon thecrevices bottom on of the the bottom part. Immediately clean the Juicer after each use. 1 bowl with water and turn on the juicer. · For easier clean up, operate the juicer for of the juicing screw. an additional 30 seconds after the juice is If remaining residue in the Juicer dries up, extracted. it can make disassembling and clean-up · When the drum lid is stuck, press the difficult. The excess buildup can cause poor REVERSE – OFF – FORWARD button in this order, switching back and forth 2 to 3 times performance in future uses. to dislodge. Then place both hands on the drum lid and firmly press down while For easier disassembly, place the Top-set in the simultaneously turning the drum lid to open. sink and run water through it. * Fill the juicing bowl with water and run the juicer before opening the drum lid. It Thoroughly dry the bottom of the screw where it may help to open the drum lid when stuck. connectsNote | toImmediately the metal cylinder clean the shaft juicer on after the eachBase . use. If remaining residue in the juicer dries Turn the drum lid counter clockwise to up, it can make disassembling and clean- Tip | Thoroughly clean the juicing screw 2 up difficult. The excess build up can cause open. ensuring that the juicing screw is clean poor performance in future uses. without any residue. For easier disassembly, place the top- Completely dry before using. set in the sink and run the water through from the top of the top-set. Note | After juicing ingredients with seeds, make Let it run for a moment. Open the sure to thoroughly clean the bottom 2 Thoroughly dry the bottom of the juicing smart cap and let the water run out of crevice of the juicing screw. (If this area screw. the juicing bowl. TIP: isn’t properly cleaned, it can cause the Thoroughly clean the screw, ensuring that it is clean without any residue.part to be damaged.) Completely dry before using. 5 Place the juicing bowl under running water. Clean the body with a soft damp towel NOTE: 7 and dry. Note | When moving the appliance, do not lift After juicing ingredients with seeds, make sure to thoroughly clean the bottom crevice of the by grabbing the feeding tube. Always lift the appliance by grabbing the body or screw. If this area isn’t properly cleaned, it can affect the balance between the screw and the handle. Strainer and damage the parts. Turn the top-set counter clockwise and 3 lift off the body.

18 19 HOW TO DISASSEMBLE AND CLEAN * The products illustrated in this booklet may vary slightly from the actual product.

1 Switch OFF and unplug the power cord 4 Remove the juicing screw, strainer and 6 Under running water, clean the outside Quick Rinsing from the wall outlet. rotation wiper unit from the juicing bowl. of the juicing screw with a dish scrub. Use Clean with provided brush. the tip of the cleaning brush to push out Note | · Extract all the remaining pulp in the With the smart cap closed, fill the juicing juicing bowl before stopping the juicer. any residue in the crevices on the bottom 1 bowl with water and turn on the juicer. · For easier clean up, operate the juicer for of the juicing screw. an additional 30 seconds after the juice is extracted. · When the drum lid is stuck, press the REVERSE – OFF – FORWARD button in this order, switching back and forth 2 to 3 times to dislodge. Then place both hands on the drum lid and firmly press down while simultaneously turning the drum lid to open. * Fill the juicing bowl with water and run the juicer before opening the drum lid. It may help to open the drum lid when stuck. Note | Immediately clean the juicer after each use. If remaining residue in the juicer dries Turn the drum lid counter clockwise to up, it can make disassembling and clean- Tip | Thoroughly clean the juicing screw 2 up difficult. The excess build up can cause open. ensuring that the juicing screw is clean poor performance in future uses. without any residue. For easier disassembly, place the top- Completely dry before using. set in the sink and run the water through from the top of the top-set. Note | After juicing ingredients with seeds, make Let it run for a moment. Open the sure to thoroughly clean the bottom 2 Thoroughly dry the bottom of the juicing smart cap and let the water run out of crevice of the juicing screw. (If this area screw. the juicing bowl. isn’t properly cleaned, it can cause the ® HOW TO DISASSEMBLE AND CLEAN part to be damaged.) ROYAL PRESTIGE 17 JUICER* The products illustrated in this booklet may vary slightly from the actual product. Place the juicing bowl under running 5 water. 1 Switch OFF and unplug the power cord Remove the juicing screw, strainer and Clean theUnder body running with a soft water, damp clean towel the outside 1 4 rotation wiper unit from the juicing bowl. 7 and6 dry. Quick Rinsing Note | Whenfrom moving the the wall appliance, outlet. do not lift of the juicing screw with a dish scrub. Use by grabbing the feeding tube. Always lift Clean with provided brush. the tip of the cleaning brush to push out Clean the base with a soft damp towel and dry. Note | · Extract all the remaining pulp in the With the smart cap closed, fill the juicing the appliancejuicing by bowl grabbing before the stopping body or the juicer. any residue in the crevices on the bottom 6 1 handle. bowl with water and turn on the juicer. · For easier clean up, operate the juicer for of the juicing screw. an additional 30 seconds after the juice is 3 Turn the top-setextracted. counter clockwise and lift off the ·body.When the drum lid is stuck, press the TIP: If the towel is dripping wet, make sure REVERSE – OFF – FORWARD button in this to squeeze out the excess liquid before order, switching back and forth 2 to 3 times to dislodge. Then place both hands on using it on the Juicer . the drum lid and firmly press down while Tip | It is not necessary to completely clean simultaneously turning the drum lid to open. NOTE:the juicerSoak in the between bowl makingin a solution multiple of warm water juices during a single juicing session. * Fill the juicing bowl with water and run with baking soda or a little bit of bleach to clean TIP | the juicer before opening the drum lid. It The round brush can clean the juice the Whenexcess finished buildup with. juicing, always may help to open the drum lid when stuck. spout of the juicing bowl. disassemble and clean thoroughly Note | Immediately clean the juicer after each Note | If the towel is dripping wet, make sure between juicing sessions to prevent HOW TO DISASSEMBLE AND CLEAN use. If remaining residue in the juicer dries to squeeze out the excess liquid before residue buildup. Turn the drum lid counter clockwise to up, it can make disassembling and clean- using it on the juicer. * The products illustratedTip in this | bookletThoroughly may vary slightly clean from the actual juicing product. screw 2 up difficult. The excess build up can cause open. ensuring that the juicing screw is clean poor performance in future uses. 18 Quick Rinsingwithout any residue. 19 1 Switch OFF and unplug the power cord Remove the juicing screw, strainer and UnderFor runningeasier disassembly, water, clean place the outside the top- 1 4 6 Quick RinsingCompletely dry before using. from the wall outlet. rotation wiper unit from the juicing bowl. of theset juicingin the sink screw and with run the a dish water scrub. through Use With the cap closed, fill the juicing bowl with water and Let it run for a moment. Open the cap and let the water 1 Note | After juicing ingredients with seeds, make 2 Let it run for a moment. Open the Clean with provided brush. the fromtip of the the top cleaning of the top-set. brush to push out turn on the Juicer . run out of the bowl. Note | · Extract all the remaining pulp in the sure to thoroughly clean the bottom 2 Thoroughly dry the bottom of the juicing With the smart cap closed, fill the juicing smart cap and let the water run out of juicing bowl before stopping the juicer. any residue in the crevices on the bottom 1 crevice of the juicing screw. (If this area screw. bowl with water and turn on the juicer. the juicing bowl. · For easier clean up, operate the juicer for of the juicing screw. isn’t properly cleaned, it can cause the an additional 30 seconds after the juice is part to be damaged.) extracted. · When the drum lid is stuck, press the 5 Place the juicing bowl under running REVERSE – OFF – FORWARD button in this water. Clean the body with a soft damp towel order, switching back and forth 2 to 3 times 7 and dry. to dislodge. Then place both hands on Note | When moving the appliance, do not lift the drum lid and firmly press down while by grabbing the feeding tube. Always lift simultaneously turning the drum lid to open. the appliance by grabbing the body or * Fill the juicing bowl with water and run handle. the juicer before opening the drum lid. It may help to open the drum lid when stuck. Turn the top-set counter clockwise and Note | 3Immediatelylift off cleanthe body. the juicer after each use. If remaining residue in the juicer dries Turn the drum lid counter clockwise to up, it can make disassembling and clean- Tip | Thoroughly clean the juicing screw 2 up difficult. The excess build up can cause open. ensuring that the juicing screw is clean poor performance in future uses. without any residue. Tip | It is not necessary to completely clean For easier disassembly, place the top- the juicer in between making multiple Completely dry before using. set in the sink and run the water through juices during a single juicing session. Note | from the top of the top-set. TIP | AfterThe round juicing brush ingredients can clean with the seeds, juice make Let it run for a moment. Open the When finished with juicing, always sure to thoroughly clean the bottom 2 Thoroughly dry the bottom of the juicing spout of the juicing bowl. TIP: smart cap and let the water run out of disassemble and clean thoroughly crevice of the juicing screw. (If this area screw. the Notejuicing | bowl.If the towel is dripping wet, make sure between juicing sessions to prevent isn’t properly cleaned, it can cause the It is not necessary to completely clean the Juicer when making multiple juicesresidue during buildup. part to be damaged.) to squeeze out the excess liquid before a single juicing sessionusing. it on the juicer. Place the juicing bowl under running 5 18 When finished juicing, always disassemble and clean thoroughly to prevent residue buildup. 19 water. Clean the body with a soft damp towel 7 and dry. Note | When moving the appliance, do not lift by grabbing the feeding tube. Always lift the appliance by grabbing the body or handle.

Turn the top-set counter clockwise and 3 lift off the body.

18 19 ® 18 ROYAL PRESTIGE HOW TO CLEAN SILICONE PARTS JUICER HOW TO USE THE CLEANING TOOL * The products illustrated in this booklet may vary slightly from the actual product.

Tip | Clean the rotation wiper under running water. Tip | The cleaning tool makes clean-up quick and easy. Thoroughly dry after cleaning. Before assembling the top-set, ensure that the silicone ring is Completely dry after cleaning. How firmlyto inserted.Clean Silicone Parts Note | If the silicone ring is not firmly inserted, juice may leak from the bottom of the juicing bowl. Tip: Clean the Rotation Wiper under running water. Thoroughly dry after cleaning.

SiliconeSILICONE Brush BRUSHES Hold the cleaning tool with one hand and insert Pull out the silicone brush from 1 the strainer into the cleaning tool. Pull out the Silicone brushes from the rotation wiper to clean. the rotation wiper to clean. Note | Insert the strainer until you hear a click. AfterAfter cleaning, cleaning, insert insert into into the theslot slot with the tail pointing down as withshown the tail in pointingthe illustration. down as shown in the illustration.

Silicone Ring RemoveSILICONE the silicone RING ring from Under running water, rotate the cleaning tool strainerRemove to clean. the silicone ring from the strainer to clean.2 and the strainer in opposite directions to clean. AfterAfter cleaning, cleaning, push push in the in thesilicone silicone ring with the smaller surface ring. facing down.

SmartCAP Cap RemoveRemove from from the the juice juice spout spout to clean. to clean. 3 Thoroughly rinse the inside and outside of AfterAfter cleaning, cleaning, attach insert the the smart silicone piece into the cap andthe attachstrainer under running water. capthe to capthe smartinto the cap juice silicone spout. on the juice spout.

Cleaning inside of the bowl Please unscrew the cover on the bottom and clean inside. After cleaning, remove the strainer from the After cleaning, make sure that protrusion part of gear is 4 cleaning tool. Dry before storing. placed on the outer part so it fits (connects) with the drum. Sequence of assembly is in reverse order of disassembly.

20 21 ® ROYAL PRESTIGE 19 JUICER

How to Use the Rotating Brush

Tip: The rotating brush makes clean-up quick and easy. Completely dry after cleaning. HOW TO CLEAN SILICONE PARTS HOW TO USE THE CLEANING TOOL Note: Use the included Cleaning Brush to remove hard-to-reach* The products bits illustrated after in thisusing booklet the may rotatingvary slightly frombrush the actual. product.

Tip | Clean the rotation wiper under running water. Tip | The cleaning tool makes clean-up quick and easy. Thoroughly dry after cleaning. Before assembling the top-set, ensure that the silicone ring is Hold the rotatingCompletely brush with dry one after hand cleaning. and insert the firmly inserted. 1 strainer into the brush. Note | If the silicone ring is not firmly inserted, juice may leak from the bottom of the juicing bowl.

NOTE: Insert the Strainer until you hear a click.

Silicone Brush Hold the cleaning tool with one hand and insert Pull out the silicone brush from 1 the strainer into the cleaning tool. the rotation wiper to clean. Note | Insert the strainer until you hear a click. After cleaning, insert into the slot with the tail pointing down as shown in the illustration. Under running water, rotate the rotating brush and the 2 strainer in opposite directions to clean.

Silicone Ring Remove the silicone ring from Under running water, rotate the cleaning tool strainer to clean. 2 and the strainer in opposite directions to clean. After cleaning, push in the silicone ring.

Thoroughly rinse the inside and outside of the strainer 3 under running water. Smart Cap Remove from the juice spout to clean. 3 Thoroughly rinse the inside and outside of After cleaning, attach the smart the strainer under running water. cap to the smart cap silicone on the juice spout.

After cleaning, remove the strainer from the rotating 4 Cleaning inside of the bowl brush. Dry before storing. Please unscrew the cover on the bottom and clean inside. After cleaning, remove the strainer from the After cleaning, make sure that protrusion part of gear is 4 cleaning tool. Dry before storing. placed on the outer part so it fits (connects) with the drum. Sequence of assembly is in reverse order of disassembly.

20 21 ® 20 ROYAL PRESTIGE JUICER

Troubleshooting Q&A

CONDITION REASON SOLUTION There is no power Juicer will not operate if parts are • Check if the power cord is properly plugged in. to the Juicer not assembled properly. • Check if the Feed tube and the bowl are properly assembled. • Check to see if the Top-set and the Base are properly assembled.

Low juice yield Each ingredient has different • If the ingredient itself has low water content, it may amounts of liquid that will yield help to soak it in water before juicing. different amounts of juice. • If juicing ingredients with small seeds, after a few If the ingredients are not fresh, servings, it may reduce the juice yield. For best they may contain reduced results, disassemble and wash the Top-set in amounts of fluid, which will between juicing. yield less juice. • If there is seed residue on the bottom of the Strainer, this can affect Juicer performance and the overall juice yield.

There is too much pulp When continuously juicing, and • To reduce the fine pulp, clean the in the juice depending on the ingredient, the Top-set frequently and extract the pulp. juice may contain a lot • Use a mesh strainer and put the juice through it to of fine pulp. collect the unwanted pulp. • If the Strainer and the screw are damaged and affecting the Juicer ’s performance, it is recommended the parts be replaced. • The lifetime of each part may vary depending on length and method of use and ingredients extracted. To order parts, see customer service information on page 24. • If too many ingredients are inserted at the same time, it may cause the Juicer to stop frequently. This can lead to pulpy juice. Insert the ingredients slowly. ® ROYAL PRESTIGE 21 JUICER

CONDITION REASON SOLUTION The Feed tube The screw may not be • Make sure the screw is pushed all the will not close properly inserted. way into the Strainer for the Feed tube to close properly.

Odd noise from Check if the parts are • Try reassembling the parts and listen for the the Juicer assembled correctly. odd noise. Operating the Juicer without • Do not start the Juicer unless there are ingredients ingredients can cause damage to and/or liquid in it. the screw. • The friction noise from the screw and the If the size of ingredients is too Strainer will cease when ingredients are inserted large, friction noise into the Juicer . will occur. • Check the size of the ingredients. The noise can occur if the Juicer • Place the Juicer on a horizontally flat surface when is operated on an uneven or operating. slanted surface.

The extracted pulp is During the very beginning Select fresh ingredients. very moist of extraction, the pulp can be moister. Depending on the ingredient’s condition, especially when the ingredient is not fresh, the juice can be extracted with the pulp.

During operation, the The screw and the Strainer are No action is required. bowl shakes set up to crush and squeeze the ingredients. It is normal for the screw and the Strainer to vibrate. If the ingredient contains strong fiber, the vibration from the Top-set may be stronger.

Layers of Depending on the density of the No action is required. separation in the juice ingredients, the extracted juice may show layers of different juices. It is different from separation due to oxidation caused by juicing with a high-speed Juicer . ® 22 ROYAL PRESTIGE JUICER

CONDITION REASON SOLUTION During juicing, the If too many ingredients are • Check the power cord and make sure it is Juicer stopped inserted at one time, this can plugged in correctly. cause the Juicer • Check that all the parts are correctly assembled. to stop. • Press the REVERSE - OFF - FORWARD button in this The Juicer stops due to the order, switching back and forth 2 to 3 times. overload protection. • The REVERSE setting will push the ingredients Hard seeds can damage the up, and the FORWARD setting will pull the Juicer . ingredients down. • Let it cool for 30 minutes to 2 hours before juicing again. • If there are hard seeds within the ingredients, remove them before juicing. The Feed tube is stuck If there is too much pulp in the • After juicing, let the Juicer operate for another 30 top-set, this can cause the feed seconds to extract the remaining pulp. tube to not open. • In this situation, press the REVERSE OFF - FORWARD button in this order, switching back and forth 2 to 3 times. • Pour water down the feed tube to rinse out the inside and then try opening it. Fibers are Ingredients with tough, long • When juicing fibrous ingredients, do not collect wrapping around fibers are more difficult to juice more than 0.5 liter ( approx. 2 ¼ cups) of juice. After the screw and are collecting this quantity or less, clean the top-set affecting performance completely before juicing again ® ROYAL PRESTIGE 23 JUICER

CONDITION REASON SOLUTION Discoloration of After juicing, the remaining pulp inside • Clean Juicer thoroughly after use. the plastic parts the top-set can dry, which can make • The silicone pieces on the top-set can disassembling and cleaning hard. This can also be detached to be thoroughly cleaned. affect the Juicer ’s performance and color. • Rub vegetable oil on the dyed areas and Ingredients that are rich in carotenoids, such use mild detergent to clean. as carrots and spinach, may dye plastic parts. NOTE: Vegetable oil should only be used during clean-up for parts that are discolored. Do not use vegetable oil on the screw or the strainer.

Using for purposes This Juicer is designed to juice ingredients like • Do not use the Juicer for extracting other than juicing fruits and vegetables. vegetable oil. If vegetable/animal oil gets on the screw or • Do not juice ingredients with high the strainer, this can affect the performance contents of vegetable/ animal oil. of the Juicer and could result in damaged parts.

Technical Information Product Juicer Type Low speed compression juicer Model JU0024 (ULD - 372CB) Rated Voltage 120V AC Rated Frequency 60Hz Rated Power 240 Watts Maximum Use Less than 30 minutes continuous Weight 15 lbs Dimension Height: 18.3 inches Length: 7.2 inches Width: 9.5 inches Origin Korea Manufacturer NUC Electronics CO., Ltd. ROYAL PRESTIGE® 24 JUICER

For detailed warranty information, visit Royal Prestige® on the web at www.royalprestige.com

For warranty service, send the product to our Service Center:

USA, CANADA, DOMINICAN REPUBLIC MÉXICO COLOMBIA HY CITE ENTERPRISES, LLC HY CITE MÉXICO S. DE R.L. DE CV. HY CITE ENTERPRISES ROYAL PRESTIGE® SERVICE CENTER AVENIDA TESISTAN # 2450 COLOMBIA S.A.S. 2115 PINEHURST DRIVE NAVE 18 COLONIA EL TIGRE CALLE 90 NO. 12-28, PISO 3 MIDDLETON, WI 53562 ZAPOPAN, JALISCO C.P. 45134M CHICO, BOGOTÁ, COLOMBIA PHONE: 1-800-279-3373 PHONE: 01-800-111-1116 PHONE: (571) 745-8694 BILINGUAL (ENGLISH & SPANISH) 018000 128694

PERÚ BRASIL ARGENTINA HY CITE PERÚ S.R.L. ROYAL PRESTIGE DO BRASIL HY CITE BA S.R.L. CALLE. CANTUARÍAS #160, 170, 176 COMÉRCIO E IMPORTAÇÃO SUIPACHA 552, PISO 1, DE UTILIDADES DOMÉSTICAS LTDA. OFICINA #702 – EDIFICIO CANTUARÍAS ALAMEDA ARAGUAIA, CAPITAL FEDERAL, BUENOS AIRES, MIRAFLORES, LIMA-PERÚ 2.104 - 22º ANDAR SALAS 223 A/224 A ARGENTINA, C.P. 1008 PHONE: (511) 243-7756 CENTRO EMPRESARIAL PHONE: 0800 4442904 / (511) 243-7768 ARAGUAIA CORPORATE - ALPHAVILLE BARUERI - SP, CEP: 06455-000 PHONE: (11) 4191-5026

OR 10-18