2016 Pilot’s Handbook

Mar 2016 Agriculture and Forestry / 2016 Pilot’s Handbook

Table of Contents CONTACT INFORMATION ...... 5 INTRODUCTION ...... 6

FOREST AREA ADMINISTRATIVE BOUNDARIES MAP ...... 7 PRESUPPRESSION PREPAREDNESS SYSTEM (PPS) ...... 8 MAN-UP UP CRITERIA ...... 8 INCIDENT COMMAND SYSTEM ...... 9 Incident Command Organization Structure Chart ...... 9 Operations Section Organization Chart ...... 10 ROLE OF THE AIR OPERATIONS BRANCH ...... 10 Air Operations Branch Director (AOBD) ...... 10 Air Support Group Supervisor (ASGS) ...... 11 Helibase Manager (HEBM) ...... 11 Loadmaster (LOAD) ...... 11 Helibase Radio Operator (RADO) ...... 11 Helicopter Coordinator (HLCO) ...... 11 Air Attack Officer (AAO) ...... 12 Air Tactical Group Supervisor (ATGS) ...... 12 AIRCRAFT HIRING AND REQUIREMENTS ...... 12

DEFINITIONS ...... 12 HIRING AUTHORITY...... 12 HIRING PRIORITY ...... 13 RELEASING ...... 14 SUBSTITUTING ...... 14 WEBAIR ...... 14 UNSERVICEABLE AIRCRAFT ...... 15 LOCAL CHARTERS – FOREST AREA RESPONSIBILITIES ...... 15 PROVINCIAL CHARTERS - PFFC RESPONSIBILITIES ...... 15 MINIMUM EQUIPMENT REQUIREMENTS (BEYOND TRANSPORT REQUIREMENTS) ...... 16 Required ...... 16 Wildfire Operations – Required ...... 17 Wildfire Operations – Preferred ...... 17 Specialty Operations ...... 17 Required Equipment Fixed-Wing ...... 18 Tracking Device Requirements for Wildfire Management Operations ...... 18 ACCOUNTS AND EXPENSES ...... 18

GENERAL ...... 18 Annual Fleet List – Rotor Wing ...... 19 Daily Flight Report (AO-02) ...... 19 Signing Authorities ...... 20 Wildfire Management ...... 20 Verification and Approval Process ...... 20 Sample AO-02 ...... 21 GOVERNMENT PAYMENT SCHEDULE...... 22 Flying Time ...... 22 Fuel Expenses ...... 23 Landing Fees ...... 23 Flight Crew Meals, Accommodations, and Transportation...... 23 Meals ...... 23 Accommodations ...... 24 Transportation ...... 24 THE PILOT...... 25

QUALIFICATIONS ...... 25 Fixed - Wing Aircraft ...... 25 1. Twin-engine turbine and piston powered fixed wing aircraft (over 5,800 kg) ...... 25 2. Twin-engine piston and single-engine turbine (under 5,800 kg) ...... 25 3. Single-engine piston ...... 25 4. All float equipped aircraft (in addition to sections 1, 2, 3 above) ...... 25 Rotor Wing Aircraft ...... 26 Wildfire Operations ...... 26 Wildfire Support (exemption for limited competencies, limited to recon, IR aircraft, mission type) ...... 26 March 2016 2016 Pilot’s Handbook Page 2 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Rappel Operations ...... 26 Helitorch Operations ...... 27 Natural Resource Management, Reconnaissance and Surveys ...... 27 PILOT RESPONSIBILITY ...... 27 Briefing of Passengers by Pilot ...... 27 BRIEFING OF PILOT ...... 28 Briefing Packages ...... 28 Provincial Forest Fire Center (PFFC)...... 29 Area Fire Centers ...... 29 Incident Briefing Package ...... 29 Contents of Briefing Package ...... 30 Air space Management plan ...... 30 RADIO USE, AIRSPACE MANAGEMENT, AND FLIGHT FOLLOWING ...... 32

CLASS F AIRSPACE MANAGEMENT ...... 32 Outside Class F Airspace (Transiting to and from the fire) ...... 33 Approaching Class F Airspace (Approaching the fire) ...... 33 FLIGHT PLANS AND FLIGHT MONITORING ...... 34 Flight Following and Flight Plans ...... 34 Flight Itinerary with Flight Following Radio Watch ...... 34 Flight Itinerary without Flight Following Radio Watch ...... 35 OPERATION SAFETY AND PROCEDURES ...... 35

FLIGHT MANAGEMENT GENERAL RESTRICTIONS AND REQUIREMENTS ...... 35 PILOT’S DUTY DAY ...... 36 MANDATORY REST PERIODS ...... 36 FLIGHT HOUR LIMITATIONS ...... 36 Maximum Daily Flight Time ...... 36 Rotor wing – Suppression and Presuppression Assignments ...... 36 Rotor wing – General Duty Assignment ...... 37 Rotor wing – Infrared Scanning ...... 37 Fixed-Wing Airtankers – Initial Attack Fires ...... 37 Fixed-Wing Airtankers – Support Action Fires ...... 37 Fixed-Wing Casual Charter and Fixed-Wing Spray Aircraft ...... 38 LOW LEVEL OPERATIONS (<500 FEET AGL) ...... 38 General ...... 38 Rotor Wing ...... 38 Fixed Wing ...... 38 STANDARD AIRMANSHIP – CRUISING ALTITUDES...... 39 FLIGHT CREW ALERT STATUSES ...... 39 Rotor Wing ...... 39 Airtankers ...... 39 Red ...... 39 Yellow ...... 39 Blue...... 40 Green Day ...... 40 Day Base ...... 41 PASSENGER/CARGO MANIFEST (FP249) ...... 41 Rotor Wing Load Calculations ...... 41 Pilot Responsibilities ...... 41 Government Representative Responsibilities ...... 42 REFUELLING OPERATIONS ...... 42 ROTOR WING SLING LOADS ...... 44 Long Line Use (Rotor wing) ...... 44 Ground Running of Engines during Bucketing or Sling Operations ...... 44 Flights with Passengers and External Loads ...... 45 Rappel Operations ...... 45 Bucket Operations ...... 45 Wildfire Operations ...... 45 Aerial Ignition on Wildfires ...... 45 Transporting Wildlife ...... 46 ENTERING OR LEAVING A HOVERING ROTOR WING IN FLIGHT ...... 46 Emergency Rotor Wing Boarding in a Hover ...... 46 Hover Exit Conditions and Limitations ...... 47 Rotor Wing Aircraft Company Compliance and Pilot Qualifications ...... 47 SAFETY CONSIDERATIONS FOR WORKING IN THE COLD LAKE AIR WEAPONS RANGE (CLAWR) ...... 47

March 2016 2016 Pilot’s Handbook Page 3 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

ALBERTA FORT MCMURRAY OIL SANDS CLASS E AIRSPACES ...... 48 North Oilsands ATF Area...... 49 South Athabasca Oil Sands Area ...... 49 UNMANNED AERIAL VEHICLE (UAV) ...... 49 DAYLIGHT FLYING UNDER VISUAL FLIGHT RULES (VFR)...... 50 Day ...... 50 Night: ...... 50 OPEN DOOR AERIAL WORK ...... 50 On the Skid or Moving Around Inside the Aircraft ...... 51 Seated and Secured Inside the Aircraft ...... 51 AIRSPACE RESTRICTION / NOTICE TO AIRMAN (NOTAM) ...... 51 TRANSPORTATION OF DANGEROUS GOODS ...... 52 Considerations for Shipping Propane Tanks ...... 52 Considerations for Shipping 365 Liter Propane Tanks ...... 52 PEPPER SPRAY ...... 53 NON-GOVERNMENT PERSONNEL ON CASUAL HIRE OR CONTRACTED AIRCRAFT ...... 53 AQUATIC INVASIVE SPECIES (AIS) PREVENTION ...... 54 FUR AND GAME FARM OPERATIONS ...... 54 AVIATION OCCURRENCE RESPONSE AND REPORTING ...... 54

AVIATION ACCIDENTS, INCIDENTS, HAZARDS, MISSING AIRCRAFT ...... 54 Reporting Aviation Near Misses/Hazards, Accidents, Incidents, and cautions ...... 55 PROCEDURES FOR AVIATION ACCIDENTS / MISSING AIRCRAFT / INCIDENTS ...... 55 Accidents and Missing Aircraft ...... 55 Missing Aircraft ...... 56 Incident ...... 57 Near Miss/Hazard Reporting ...... 58 APPENDICES ...... 59

ALPHANUMERIC WILDFIRE INCIDENT MAPS ...... 59 EXAMPLE OF AIR OPERATIONS MAP USING THE ALPHANUMERIC GRID SYSTEM ...... 60 ALBERTA THIRD SYSTEM OF SURVEY ...... 61 Subdivision ...... 61 Section...... 61 Quarter Section ...... 61 Township ...... 62 Road Allowance ...... 62 Township Range ...... 62 Meridian ...... 63 Correction Lines ...... 63 Fractional Townships and Fractional Sections ...... 64 Finding a Location Based on a Legal Description ...... 64 FIRE LINE EQUIPMENT WEIGHTS ...... 64 HELICOPTER LANDING AREAS ...... 68 Helibase...... 68 Helispot...... 68 Helipad ...... 68 GLOSSARY OF WILDFIRE TERMS ...... 69 AIRSPACE CHART 1 ...... 75 AIRSPACE CHART 2 ...... 76 AIRSPACE CHART 3 ...... 77 AIRSPACE CHART 4 ...... 78

March 2016 2016 Pilot’s Handbook Page 4 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Contact Information

Forestry Area Offices Office Location Phone Number Calgary (403) 297-8800 Edson (780) 723-8269 Fort McMurray (780) 743-7125 Grande Prairie (780) 538-5560 High Level (780) 926-3761 Lac La Biche (780) 623-5388 Peace River (780) 624-5388 Rocky Mountain House (403) 845-8272 Slave Lake (780) 849-7400 Whitecourt (780) 778-7153

Public Land Area Offices Office Location Phone Number Calgary (403) 297-8800 Edson (780) 723-8265 Fort McMurray (780) 743-7120 Grande Prairie (780) 538-8080 High Level (780) 926-5400 Lac La Biche (780) 623-5240 Manning (780) 836-2881 Rocky Mountain House (403) 845-8272 Slave Lake (780) 849-7400 Whitecourt (780) 778-7153

Fish and Wildlife Area Offices Office Location Phone Number Calgary (403) 297-6423 Edson (780) 723-8244 Fort McMurray (780) 743-7200 Grande Prairie (780) 538-5265 High Level (780) 926-2238 Lac La Biche (780) 623-5247 Lethbridge (403) 381-5281 Peace River (780) 623-6405 Rocky Mountain House (403) 845-8230 Slave Lake (780) 849-7110 Whitecourt (780) 778-7119

March 2016 2016 Pilot’s Handbook Page 5 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Introduction The purpose of this handbook is to give companies and pilots working for the department an insight into how Agriculture and Forestry conducts business. Basic information on policies, procedures, and incident command system are provided in this handbook.

Wildfire Management is now within the department of Agriculture and Forestry (AF) and is responsible for wildfire service, operations, prevention, wildfire information and community programs for approximately 52.9% of the province [349,726 square kilometres].

To help with safeguarding our forests, Alberta has a designated legislated Forest Protection Area where within the Department of Agriculture and Forestry, Wildfire Management, is responsible for wildfire suppression and has been divided into ten (10) Areas (each with their own fire centre) as listed below:

• Rocky Mountain House Forest • Grande Prairie Forest Area Area

• Edson Forest Area • Calgary Forest Area

• Lac La Biche Forest Area • High Level Forest Area

• Slave Lake Forest Area • Fort McMurray Forest Area

• Peace River Forest Area • Whitecourt Forest Area

A Forest Area Manager coordinates and monitors all forest protection activities within the Area.

The key strategy used to protect the land and forest resources is the safe, rapid and aggressive initial attack of all fires in the province. It is important that the aircraft pilot is well trained, competent and has an aircraft in good condition, well maintained, and available for daily standby as required. In addition to wildfire operations, aircraft are also used in conjunction with other resource management projects.

The primary decision-making group for all Alberta’s overall forest protection effort is the Provincial Fire Management Working Group consisting of personnel from the Provincial Forest Fire Centre (PFFC) and representatives from the Forest Areas. Overall, PFFC oversees policies and conducts audits on wildfire programs.

March 2016 2016 Pilot’s Handbook Page 6 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Forest Area Administrative Boundaries Map

March 2016 2016 Pilot’s Handbook Page 7 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Presuppression Preparedness System (PPS) The PPS system consists of two distinct parts as follows:

The first part is a deployment procedure for allocation of the committed initial attack resources based on values at risk, priorities, local fire risk, fuel types and analysis of inter – forest coverage.

The second part is a procedure to determine the Forest area man-up levels and subsequent resource commitments based on the fire severity rating.

In general terms, the PPS system works as follows:

• As the fire severity increases, additional suppression resources are committed and strategically placed to reduce travel time to a potential fire start.

• As the fire severity decreases, suppression resource levels are reduced and response times are relaxed in recognition of the lower potential for fire control problems.

Man-up Up Criteria

• Man-up is the allocation of initial attack resources strategically within the Forest Area for new fires. The objective of preparedness planning is to contain fire spread by 1000 hours the following day

• The Spatial Fire Management System (SFMS) is used to determine the time lapse that will occur before a fire reaches its threshold size. The time lapse equates to the required attack time. Wildfire Management staff can quantitatively evaluate the deployment of fire control resources that are required to meet the alert status or get-away times for each area within the forest.

• Day Basing should be in place by 1100hrs during normal risk conditions. When there is potential for holdover fires or high risk is anticipated for the morning, day- basing and loaded patrols will commence earlier than normal. When there is no potential for ignition in the morning, day basing can be delayed past 1100hrs but must be in place by 1300hrs. The Forest Area Duty Officer specifically sets rotor wing stand-to and standby times.

• Day basing of crews and rotor wing on 5, 10 or 30 minute etc. getaway times are required to areas to ensure resources are positioned strategically in the province. The locations can vary from primary fire bases with complete facilities to remote locations with no infrastructure. Generally, crews and rotor wings return to an established camp to overnight.

• When rotor wing are working long hours on fires or projects they may be exchanged for rotor wing on man-up. This should allow pilots a rest period and the engineer time to do maintenance on the machine.

March 2016 2016 Pilot’s Handbook Page 8 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Incident Command System

The Alberta Wildfire Management Branch Incident Command Organization is based on the Canadian Incident Command System [ICS] and is used to manage all wildfire emergencies and prescribed fire events.

The ICS organizational structure is specifically designed to meet the complexity and demands of single or multiple emergencies or complex planned events The Incident Command System is the combination of facilities, equipment, personnel, procedures and communications operating within a common organizational structure with responsibility for the management of assigned resources to effectively accomplish stated objectives pertaining to an incident.

Five (5) basic sections are used in forming the Basic Incident: Command, Operations, Planning, Logistics and Finance. On smaller Incidents all positions may not be activated and persons may be assigned the duties and responsibilities held by other positions.

Aircraft will typically report to the Operations Section on an incident and the Air Operations Branch if activated.

Incident Command Organization Structure Chart

March 2016 2016 Pilot’s Handbook Page 9 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Operations Section Organization Chart

Role of the Air Operations Branch The Operations Section Chief may establish an Air Operations Branch when the complexity of air operations requires additional support and effort or when the incident requires mixing tactical and logistical utilization of helicopters and other aircraft.

The number of personnel needed to perform the major functions and responsibilities assigned to the Air Operations Branch will vary based on the size and complexity of the incident. The general responsibilities of the key positions in the Air Operations Branch are as follows:

Air Operations Branch Director (AOBD) • Overall responsibility for aircraft operations on the incident • Ensure safe and efficient use of aircraft resources • Coordinate aircraft use to meet overall incident objectives • Ensure appropriate incident air support facilities in place and operational • Coordinate tactical, logistical and other uses of incident aircraft • Ensure appropriate airspace management procedures in place • Establish system for tracking aircraft utilization, and for the completion of all required documentation relating to aircraft operations

March 2016 2016 Pilot’s Handbook Page 10 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Air Support Group Supervisor (ASGS) • Responsible for management and coordination of all air support facilities and resources • Identify, manage and coordinate helibase/-spot and MRB locations • Establish and communicate air traffic control procedures • Ensure air support facilities functional and available when required • Ensure Medivac / Crash Rescue Plans are in place • Coordinate fireline requests for tactical and logistical aircraft assignments

Helibase Manager (HEBM) The HEBM has primary responsibility for managing all activities at the assigned helibase.

• Manage and supervise all helibase resources and activities • Brief pilots and solicit their input with regards to the air operations • Supervise manifesting/loading of personnel and cargo • Supervise refueling site and operations • Provide support for maintenance and repair services as required • Provide for dust abatement as required • Ensure security is in place

Loadmaster (LOAD) During highly complex helibase operations, it may be necessary to activate a LOAD. The LOAD is responsible for the safe loading/unloading of personnel and cargo. The LOAD is supervised by the HEBM.

• Responsible for the safe loading/unloading of personnel and cargo. • Ensure all passengers receive pre-flight briefings. • Supervise manifesting of personnel and cargo. • Coordinate efficient movement of personnel and cargo • Coordinate sling loads

LOAD should be briefed concerning the characteristics of each make/model helicopter assigned to ensure correct passenger and cargo placement in the aircraft.

Helibase Radio Operator (RADO) The RADO is supervised by the HEBM and is responsible for facilitating communications among assigned helicopters, helibases and air operations staff.

• Responsible for facilitating communications among assigned helicopters, helibases and air operations staff. Maintain constant communication with all helicopters. • Maintain a log of all aircraft movements and manifests • Assist with helicopter timekeeping and utilization tracking

Helicopter Coordinator (HLCO) • Manage and coordinate aerial firefighting using multiple medium and heavy helicopters • Brief pilots on tactical missions and procedures • Ensure proper documentation completed

March 2016 2016 Pilot’s Handbook Page 11 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

• Recommend need for NOTAMs and evaluate effectiveness • Select and utilize appropriate aircraft to ensure efficiency and effectiveness • Ensure all airspace management procedures are effective and being followed

Air Attack Officer (AAO) Each airtanker group has an assigned “birddog” aircraft that carries an air attack officer (AAO) and a birddog pilot. The AAO coordinates air attack operations on wildfires and ensures aerial operations are conducted in an effective, efficient and safe manner. To ensure the safety of all aircraft in the vicinity, the birddog team also manages the airspace over the fire.

Air Tactical Group Supervisor (ATGS) When two (2) Birddog aircraft are on a fire, one Birddog may assume the Air Tactical Group Supervisor (ATGS) role. Once an ATGS is established, that Birddog team will be responsible for managing the airspace for the fire. The ATGS will maintain a high altitude orbit while the tactical birddog will remain 1000 ft. AGL and continue to work with the airtankers actioning the fire. The ATGS will be identified as “Air Attack” and either the Wildfire number or a geographical identifier. For example: Air Attack Fire 31 or Round Hill Air Attack. Once ATGS has been established it will be announced on the Air Advisory and Forest Area Firenet Frequencies. Aircraft Hiring and Requirements Wildfire Management shall ensure safety audits are conducted by the Aviation Section.

Definitions

Availability: For a rotor-wing to be considered “Available’ on WebAir, the aircraft must be available to depart within one hour of hire notification. Both the rotor-wing and essential aircrew must be at the location indicated on WebAir.

Suitability is determined by aircraft type and capability, pilot qualifications, distance to point of hire, economics, local knowledge and familiarity with Agriculture and Forestry procedures.

Established Forest Area Operator: An operator with an established base located within the Forest Area with aircraft on location and available year round.

Hiring Authority

Forest Area Shall hire on a casual basis those operators situated within the Forest Area boundaries provided: • The company has a casual aircraft contract with the Department, and

March 2016 2016 Pilot’s Handbook Page 12 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

• Wildfire Management has conducted safety audits by the Aviation Safety Officer prior to an operator being hired, and a periodically thereafter. The audits must be satisfactory to WM.

Provincial Forest Fire Centre Shall hire upon request from the Forest Area(s) or Edmonton those: • Companies with casual aircraft contract with Wildfire Management, • Wildfire Management has conducted safety audits by the Aviation Safety Officer prior to an operator to an operator being hired, and periodically thereafter. The audits must be satisfactory to WM. • Out-of-province operators who have a contract with Wildfire Management • Aircraft owned or contracted to another agency via the MARS, CANUS or NWC Agreements, and

Hiring Priority WebAir Canada shall be used to determine aircraft location. All “IT” questions regarding WebAir shall be directed to the Canadian Interagency Forest Fire Centre (CIFFC) at: (204)784-2030.

Agriculture and Forestry first determines the best aircraft type or classification for the job and any other specific pilot competencies required. Hiring priorities are as follows for:

Short-term Projects or Limited Day Hires (2 days or less) 1. ‘Available’ established Forest Area operator (rotation may be required) 2. ‘Available’ un-established Forest Area operator (based on proximity, suitability and WebAir time stamp)

Long-term Projects, Presuppression and Suppression For light, intermediate and medium rotor wing the priority shall be: 1. Long term contract aircraft of the capability that is required 2. Proximity 3. Suitability and 4. WebAir time stamp

Heavy rotor wing 1. Proximity 2. Suitability and 3. WebAir time stamp

Infrared Scanning Infrared scanning hiring will be based on a provincial rotation. The rotation is annually determined by the submitted Daily Scanning Rate.

Ferry Time For aircraft positioned outside Alberta, ferry time will be paid one way from point of hire to the required work location. Note: If the aircraft is repositioned, ferry time will be paid back to the original required work location.

March 2016 2016 Pilot’s Handbook Page 13 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Releasing The intent of this procedure is to meet the needs of the operation while finding an equitable balance for operators.

When releasing rotor wing from man-up or fires, each is considered an individual project, for example: PPS is one project, *WF-060 is one project, *WF-090 is one project. Forest Areas should not be replacing helicopters from one project to another.

Within each project, rotor wing are released as follows: 1. Aircraft requesting to be released for other work or limited time commitment, 2. Casually hired aircraft based on least suitability for the work required, 3. Long term contract aircraft.

Substituting A company may substitute a rotor wing of the same type or classification provided: . The office hiring the aircraft is advised and agrees to the replacement, . The aircraft being substituted is not already on hire with the Branch, . The aircraft is registered with Transport Canada confirming that company is the owner of the aircraft, and . The aircraft is shown in WebAir to be at the same location as the intended hire.

WebAir 1) No aircraft substitutions at the time of hire 2) If an aircraft is substituted mid-hire, the aircraft will be marked as ‘Hired’ by Agriculture and Forestry at time of substitution 3) If Agriculture and Forestry contacts an operator and the aircraft is not available immediately within one (1) hour or the time required, Agriculture and Forestry will mark aircraft as ‘Unavailable’ in WebAir and move on to hire the next available aircraft 4) Operators are responsible for real time updates to their status on WebAir for availabilities, pilot competencies, training, company information, etc.

Short –term Projects or Limited Day Hires (2 days or less) Aircraft will not be marked as ‘Hired’ in WebAir

Long-Term Projects (projects exceeding 2 days), Presuppression and Suppression Agriculture and Forestry will mark aircraft as ‘Hired’ for presuppression and suppression at the time of hire and long-term projects on the first day of the project.

False Information on WebAir If a company falsely claims information (such as, but not limited to, pilot competency, aircraft position, etc.) on WebAir, the hiring Wildfire Operations Officer (or designate) or the Provincial Aircraft Coordinator will address concerns with the company and advise the Manager of Aviation and Geomatics (or designate).

If it is found that the company is intentionally providing false information on WebAir, reprimands to the company such as a verbal warning, a letter or warning, suspension of

March 2016 2016 Pilot’s Handbook Page 14 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook hire or termination of all or some of their contracts may result. Letters of warning, suspensions or contract terminations will be sent from the Manager of Aviation and Geomatics.

Unserviceable Aircraft Unserviceable is defined as when the aircraft, pilot or engineer are not in condition to perform, fails to perform or is unavailable to perform during the alert/standby period as defined in “Flight Crew Statuses” or work assignment period specified in the daily Incidence Action Plan or Forest Area daily operations plan. Note: Inoperable radios or satellite tracking modem (automated flight following) constitutes an unserviceable aircraft. When reporting unserviceable aircraft these procedures must be followed: • Advise the Forest Area immediately of unserviceable casual charter aircraft, • Begin completion of Unserviceable Aircraft Report and submit it to Forest Area Duty Officer, • Ensure the Alert Period is completed to allow for accurate adjustment(s) to any daily standby penalty charges, and • Advise the Forest Area when aircraft is serviceable again (complete that section of the report and submit it to the Forest Area Duty Officer). Casual hired aircraft unserviceable for more than 1 charter period will be released.

Local Charters – Forest Area Responsibilities The following shall be confirmed with each Forest Area operator on an annual basis rather than prior to each casual charter: • Review minimum pilot qualifications to ensure all pilots available for hire meet Wildfire Management requirements, • Review the Pilot Competencies for Helicopter Wildfire Operations to ensure pilots are only hired to their competent level • Review pilot responsibilities and expectations, and • Review minimum equipment list for rotor wing engaged in wildfire operations and ensure list is available to local operators

Provincial Charters - PFFC Responsibilities The following shall be confirmed with operators prior to each casual charter: • Review minimum pilot qualifications with operator to ensure charter pilot(s) meet Wildfire Management requirements, • Review pilot responsibilities and expectations, • Review minimum equipment list for rotor wing engaged in wildfire operations, • Ensure company has provided recent work history for pilot to determine any duty limitations, and • Establish how flight watch will be managed until aircraft arrives at its initial destination.

Prior to the casual charter of any fixed-wing aircraft for movement of personnel, the option of a scheduled commercial flight for all or a portion of the move shall be investigated. If a commercial carrier is available it should be used, as there may be a considerable cost savings to Wildfire Management.

March 2016 2016 Pilot’s Handbook Page 15 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Minimum Equipment Requirements (Beyond Transport Canada Requirements) Required 1. Transport Canada approved, VHF-AM transceiver, operating in the 118.0 – 136.0 MHz frequency range, with 25 KHz spacing] with the ability to monitor two separate frequencies. 2. Transport Canada approved VHF-FM transceiver (equivalent to the Technosonic TFM138B) capable of operating on 138.0 – 174.0 MHz transmit-and-receive, with a selectable audible tone option, and capable of narrow banding, on a channel to channel basis

Note: All radios must be useable by the pilot with a “push to talk” button on the cyclic. 3. Preferred - Transport Canada approved VHF-FM transceiver (similar model but not limited to TDFM 136B programmable transceiver or equivalent) capable of programming and retaining 99 or more channels e of operating on 138.0 – 174.0 MHz transmit-and-receive with full access to CTCSS sub-audible tones, Network Access Codes (NAC) and be switchable by the operator to any of the 32 standard CTCSS tones or one of the 4096 NAC codes and capable of narrow banding and a minimum of one guard channel.

Note: Various Firenet sites throughout the province have been upgraded to digital Project 25 compliant. The sites are backward compatible being that they can operate in Analog Narrowband or Digital P25 modes. This providing greater flexibility to the Firenet radio system offering multimode communication along with increased coverage in certain cases, increased traffic loading and segregation and the potential for better interoperability. The P25 feature at this time will only be utilized where radio traffic is heavy and isolation is required and only at sites that have the capability. The Digital Project 25 compliant frequencies will be used on an as needed basis for the 2016 season. When digital frequencies are required, those aircraft equipped with digital capability will be the preferred hired. Digital Project 25 compliant VHF-FM transceivers will be required equipment for the 2017 fire season.

4. Intercom communications with a minimum of one headset per seat for light and intermediate rotor wing, a minimum of one headset for each front seat and a minimum of four headsets for the rear seats in medium rotor wing. All headsets are to be “David Clark” equivalent in quality,

5. Hobbs meter (except heavy helicopters) triggered by switches installed on the collective column and aircraft transmission oil pressure that is activated when aircraft is in flight or during full power ground hovers. Hour meter calibrated to show readings in hours and tenths of hours. When specialty or out of province rotor wing without Hobbs meters are hired, a method of determining accurate flight time, such as audited pilot log books or helibase manager records, must be used for billing. Aircraft with an unserviceable Hobbs meter will require review and recording of the March 2016 2016 Pilot’s Handbook Page 16 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Pilot log book for validation of all flight hours. Alternative devices to the standard Hobbs meter will be permitted as long as they provide an audit function that will record individual flight airtime and a cumulative tally of airtime for the rotor wing

6. Transponders with mode C [transmits altitude] for all aircraft and must be turned on,

7. Self-cocking, automatic locking cargo hook with both manual and electrical release,

8. Convex mirror for pilot to observe sling loads

9. Required for all helicopters to have GPS units mounted in a central position between the pilot and co-pilot station. GPS units are mounted and in a position that does not impede the passenger view from the co-pilot seat. Preferably with degree decimal minute (DMD) as the standard display Note: Fixed mounted GPS units in place on pilot side can be accepted.

10. Sleeping bag cot / foam mattress and tent[s] for each flight crew member,

11. Portable electric refuelling gear

12. Shoulder harness for all seats, except heavy rotor wing equipped with “airline style” seats.

13. Near real time tracking device that is capable of providing position, speed and heading in a standard format “AFF” (automated flight following) at a minimum of every 02 minutes as described in this document.

Wildfire Operations – Required • Rotor wing (except for the R22 and R44) must come with an approved water bucket for that rotor wing type. For rotor wing with a 170 Imperial gallon or greater capacity bucket, the bucket is to be foam equipped and include a long line. • Minimum of two (2) cargo nets of appropriate size for the aircraft and two lanyards and • Medium and heavy rotor wing must come with at least one (1) long line with remote hook and be equipped with properly installed cabin equipment for the helicopter type, such as doors, windows and dual controls.

Wildfire Operations – Preferred All rotor wings with a bucket capacity of greater than 150 imperial gallons be equipped with a foam injection system for the bucket.

Specialty Operations Any speciality operations such as long lining, fish stocking or wildlife netting, may require other equipment, which will be identified at the time of hire.

March 2016 2016 Pilot’s Handbook Page 17 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Required Equipment Fixed-Wing Specialized equipment or configuration that is required must be specified at the time of hire. Equipment includes but is not limited to • VHF FM radios • headsets, • cargo configuration • Internal communications systems.

Tracking Device Requirements for Wildfire Management Operations

Tracking systems are mandatory for all Rotor Wing and Fixed Wing.

The satellite system must meet the USAFF XML data specification and either push the data to a WM server or allow WM services to pull the data from its data server.

• Must be AFF [automatic flight following] compliant. • Must be connected to the aircraft power source. • Installed in such a manner that the GPS and Satellite antennas have maximum vertical exposure to ensure connectivity with the satellites. • Installation is approved via an Engineering Order [EO], Limited Supplemental Type Approval [LSTA], or a Supplemental Type Certificate [STC]. • Secure in such a manner that in the event of a firm landing it will not become dislodged and pose a risk to cabin crew.

NOTE: Provide Wildfire Management [Provincial Forest Fire Center, Edmonton] with the ESN # [electronic serial number] for entry into the tracking system. Accounts and Expenses General Invoices for flights conducted by Agriculture and Forestry must be directed to Aircraft Accounts at the Provincial Forest Fire Centre.

Aircraft Accounts provides Accounts Payable with verification of project and coding for all departmental aircraft.

Payments are not authorized by DPO or Master Card.

The Government of Alberta (GOA) Daily Flight Report (AO-02) signed by the designated authority of the Department will be the basis for payment made. Company flight reports may be used instead of an GOA AO-02 if pre-approved by the Provincial Forest Fire Centre - Air Operations.

The green copy of the flight report is left at the Forest Area office and the company retains the white and yellow copies. The Company must submit the original copy of flight ticket with the invoice for payment.

March 2016 2016 Pilot’s Handbook Page 18 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Annual Fleet List – Rotor Wing By January 15th of each year, the Air Operations Section of the Wildfire Management Branch will email a current Fleet List to all companies with a valid casual charter contract. This Fleet List will include all aircraft that Wildfire Management has on file for each eligible company. Companies are required to review, and if the fleet list is correct, must sign, date and send back to the Air Operations Section. If any updates or changes need to be made to the Fleet list, companies are required to make those adjustments and send back to the Air Operations Section who will then review and make any necessary adjustments and return for date and signature. All finalized Fleet Lists are to be returned to the Air Operations Section by March 31st of the current year. Any updates to the Fleet List throughout the season must be done prior to hire. Any invoicing discrepancies will reference the signed Fleet List. Failure to return a signed Fleet List by March 31st of the current year will result in Wildfire Management defaulting to the most recent aircraft list on file, in turn generating payment for the aircraft on file. Note: This Fleet List is a record of aircraft on file with the Alberta Wildfire Management Branch and may differ from those aircraft listed on WebAir Canada. Management of the aircraft listed on WebAir Canada is the responsibility of each individual company.

Daily Flight Report (AO-02) Flight tickets are the basis of payment and the audit trail document. The following information must be on the flight ticket.

• Flight Date; • Contractor Name; • Aircraft Type; • Aircraft Registration; • Initial Point and Time of Departure; • Location and Time Aircraft is DFN (Down For Night); • Pilot(s) Printed Name; • Engineer(s) Printed Name; • Aircraft Departing From, Roll/Up Time; • Aircraft Arriving At, Stop/Down Time; • Total Flight time according to Meter Reading, Start and Finish and Difference (If Aircraft has no meter, an explanation must be provided); • Aircraft Flight Codes, to be included are: Activity code, Organization code, and Program code (Department Representative will provide these); • Any landing Fees to be charged; • Identify if any Dangerous Goods were transported; • Identify that safety briefing were conducted with all passengers; • Names of Passengers; • Purpose of Flight; • Contractor supplied Fuel, number of litres and cost per litre; • Crew expenses supplied by Vendor, breakfast, lunch, dinner, hotel, per diem allowance and/or vehicle rental; • Signature of Pilot; and • Signature, printed name, title and telephone number of Department Representative responsible for flight time and costs.

March 2016 2016 Pilot’s Handbook Page 19 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Note: All eligible aircrew expenses and fuel supplied by the vendor must be recorded on the Daily Flight Report (AO-02). If these chargers are not recorded on the Daily Flight Report, payment for these charges will not be honored.

Signing Authorities

Wildfire Management Only the following personnel are authorized to sign the Daily Flight Report (AO-02)

• Permanent Wildfire Rangers, Technologists and Operations Officers, • Permanent Forest Officers, Foresters, • Fish &Wildlife Technicians and Biologists, • Agrologists, Land Management Officers, • Management, • Employees not included in this list, with written authorization from the Forest Area Manager or a Director. A copy of this authorization must be sent to the Manager, Aviation Unit in PFFC, • Helitack, Rappel and Unit Crew Leader and Sub-Leader, Task Force and Strike Team Leader, • Contract Air Attack Officers, Contract Air Support Group Supervisor and Air Operations Branch Director • Dispatch Supervisor • Airtanker Base Personnel, • Wage Forest Officers, Wildfire Rangers and Manup Supervisors • Communication Technicians, • Permanent Hinton Training Centre employees, and • Out-of-Province and out-of-service Incident Management Team members, with written authorization from the Forestry Area Manager.

The person signing the Daily Flight Report (AO-02) should be a person who was on-board the flight, or coordinating the flight, and can verify the details of the flight and any expenses incurred.

Verification and Approval Process

March 2016 2016 Pilot’s Handbook Page 20 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Sample AO-02

March 2016 2016 Pilot’s Handbook Page 21 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Alberta Government Payment Schedule 1. A separate invoice must be submitted for each aircraft registration. Invoices must be submitted to the Provincial Forest Fire Centre (PFFC), Aircraft Accounts in a timely fashion. A suggested guideline is that invoices should be submitted to PFFC on the 15th and 30th of each month. NOTE: Direct Purchase Orders or any other form of purchase order cannot be used for hiring or payment of aircraft accounts. 2. The Department is not responsible for any claims not covered by a valid tariff. 3. When using Wildfire Management allocated funds, an authorized authority must sign the company flight report/ticket. 4. When assisting Wildfire Management, Canadian Forces aircraft are subject to military procedures in emergency situations. The Canadian Forces will bill Wildfire Management for services rendered so it is imperative that military staff receive instructions on how to properly fill out and submit Flight Reports. 5. When a vendor supplies fuel and/or oil, the number of litres must be shown on the company and Departmental flight report/ticket. If not reflected, payment for these charges will not be honoured. 6. The AO-02 flight report cannot be changed after authorized Department personnel have certified it. If changes are required, a company representative and a representative from the hiring agency must initial the changes. 7. Company flight reports/tickets submitted without Government authorization will be returned to the company.

Appropriate, original documentation to support claims for flight crew expenses or other miscellaneous claims must accompany the original copy of the flight report and be mailed to: Attention: Aircraft Accounts Unit Forestry Division, Wildfire Management Branch 9915-108 St 9th Floor, Great West Life Building Edmonton, Alberta T5K 2M4

To ensure departmental standards are maintained province wide, each Forest Area must comply with procedural guidelines regarding aircraft hiring and invoicing policies.

Flying Time When determining the duration of a flight, fractions of an hour are rounded to the nearest multiple of six minutes and expressed as decimals of an hour.

0 - 2 min = 0.0 21 - 26 min = 0.4 45 - 50 min = 0.8

3 - 8 min = 0.1 27 - 32 min = 0.5 51 - 56 min = 0.9

9 - 14 min = 0.2 33 - 38 min = 0.6 57 - 60 min = 1.0

15 - 20 min = 0.3 39 - 44 min = 0.7

March 2016 2016 Pilot’s Handbook Page 22 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Fuel Expenses Agriculture and Forestry makes every attempt to supply aviation fuel located at Wildfire Management maintained fuel caches. While hired with Agriculture and Forestry, companies are expected to use Wildfire Management fuel when supplied. There may be times when the Duty Officer or divisional representative may request the aircraft company to supply fuel. When an aircraft company is requested to supply fuel and/or oil, the number of litres must be shown on theAO-02 Flight Report. If not reflected on the AO-02 Flight Report or the company supplies fuel and/or oil without being requested to, payment for these charges may not be honoured. Aircraft companies are expected to: • report for a hire with adequate fuel and leave at the end of a hire fueled up • use Agriculture and Forestry supplied fuel when available

Landing Fees Any landing fees incurred while working for the department will be reimbursed at cost with the submission of invoice and supporting receipts. Any landing fees must be recorded on the Daily Flight Report (AO-02) in the “Landing Fees to be charged” section. Invoices without receipts and supporting documents payment for these charges may not be honored.

Flight Crew Meals, Accommodations, and Transportation Meals, accommodation and vehicle rental for all aircraft crew can be claimed when the aircraft starts and finishes its day away from its point of hire. If the aircraft starts and finishes its day at the point of hire the aircrew(s) and supporting engineering staff are NOT eligible for any subsistence claim. The aircraft company must submit original receipts when claiming any accommodation expenses, in excess of limits or for duplicate rooms. Under no circumstances shall charges be allowed for alcoholic beverages. All eligible aircrew expenses supplied by the vendor must be recorded on the Daily Flight Report (AO-02). If these charges are not recorded on the Daily Flight Report, payment for these charges will not be honored.

Meals Flight crews are expected to:

• Use closest kitchen facility maintained by Wildfire Management for the purpose of feeding seasonal firefighters, such as fire camps, secondary or primary camps, or contract kitchens, • When more convenient and feasible, eat near their place of accommodation, if different from above location; for example, when staying at a hotel in town they may take breakfast there rather than drive out to a base, however, the flight crew may not claim the meal on their expense claim, and • Eat pre-packed lunches from any source but primarily Wildfire Management contracted kitchens.

Wildfire Management will attempt to maintain the following minimum standards for all flight crews during the initial stages of mobilization of a campaign fire camp:

March 2016 2016 Pilot’s Handbook Page 23 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Day One: Food will be made available; however, delivery times will be intermittent. Flight crews should be prepared with enough rations for the first burning period. Day Two: Initial set-up of Wildfire Management camp, or equivalent, will provide food services. Day Three: Scheduled meals will be available based on flight crew schedule.

Accommodations Canadian Air Regulations defines suitable accommodation as: "a single-occupancy bedroom that is subject to a minimal level of noise, is well ventilated and has facilities to control the levels of temperature and light or, where such a bedroom is not available, an accommodation that is suitable for the site and season, is subject to a minimal level of noise and provides adequate comfort and protection from the elements"

In remote locations (temporary firebases or camps), the Department will make every attempt to supply aircrew with suitable accommodations. In the event the Department cannot provide accommodations and the contractor is eligible for subsistence claims, the contractor will be reimbursed at cost upon submission of an invoice with receipts or as specified in the current Wildfire Management Aircrew Subsistence rates, without receipts. In the event the Department attempts to supply suitable accommodations and the aircrew chooses not to accept, the contractor shall not be eligible for any claims. Further, any additional costs (flight time) as a result of aircrew not accepting accommodations shall not be paid.

If flight crews are required to reside in tents or similar conditions, Wildfire Management will attempt to give flight crews an overnight break once every five (5) days at the nearest hotel or similar accommodations. When scheduling overnight breaks a shortened duty day may be needed on the day of departure and/or the day of return.

Heavy fire activity or poor flying weather may extend this time at the fire camp to a maximum of 10 days. Flight crews must have a similar break every five (5) days thereafter. The Incident Commander, Air Operations Branch Director, Air Tactical Group Supervisor or the Forest Area Duty Officer is responsible for implementation of the breaks.

NOTE: That Pilot [s] should be prepared to overnight in tents on the fire during emergency and remote operations. Company is to supply tent and cot/ foam mattress. For short term only i.e. 1 to 3 night but can anticipate the 5-night policy on large incidents. Not expected to set up in poor conditions [i.e. muskeg swamp] – need dry / quiet / cool but not cold conditions.

The Incident Commander, Air Operations Branch Director or his/her designate, shall monitor fatigue of the flight crew and adjust accommodations when necessary.

Transportation Wildfire Management will not be providing pilots and engineers with Government or Government leased vehicles when hired for contract or charter. Companies may claim vehicle transportation expenses when the aircraft starts and finishes its day away from its point of hire. If the aircraft starts and finishes its day at the point of hire the aircrew(s) and supporting engineering staff are NOT eligible for any vehicle transportation claims. When March 2016 2016 Pilot’s Handbook Page 24 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook the company is eligible for vehicle transportation expenses, vehicle rentals will be reimbursed at cost upon submission of an invoice with receipts or as specified in the current Wildfire Management Aircrew Subsistence rates, without receipts. In cases where company vehicles are used for transportation, the current Wildfire Management Aircrew Subsistence Rates apply. In cases where taxis are used for transportation, receipts are required for charges over $10.00. The Pilot Qualifications When an aircraft is hired on casual charter, the pilot must be qualified to carry out the duties for which the aircraft is chartered.

Field personnel who may be requested to charter aircraft to operate under the jurisdiction of the Forest Protection Area are to use the following minimum pilot standards:

Fixed - Wing Aircraft

1. Twin-engine turbine and piston powered fixed wing aircraft (over 5,800 kg) • 2,000 hours total flying time, fixed wing aircraft • 500 hours multi-engine time, fixed wing aircraft • 500 hours pilot-in-command, fixed wing aircraft • Current Transport Canada Commercial Pilot Licence • Current Pilot Competency Check (PCC)

2. Twin-engine piston and single-engine turbine (under 5,800 kg) • 1,200 hours total flying time in a fixed wing aircraft • 100 hours multi-engine (multi-engine aircraft) or 100 hours single-engine turbine fixed wing aircraft • 200 hours pilot-in-command in a fixed wing aircraft • Current Transport Canada Commercial Pilot Licence • Current Pilot Competency Check Ride (PCC) • Proficient in operating out of short length, grass and gravel strips, and • At least six (6) months operational experience

Note: The reference to single-engine turbine is made to take into account such aircraft as the Cessna Caravan, Pilatus PC-12, the Turbo Beaver, and single- engine Turbo Beaver.

3. Single-engine piston • 600 hours total flying time • 200 hours pilot-in-command • Current Transport Canada Commercial Pilot Licence • Proficient in operating out of short length, grass and gravel strips.

4. All float equipped aircraft (in addition to sections 1, 2, 3 above) • Float endorsement • 150 hours on floats as pilot-in-command. • Float operations on isolated lakes, and

March 2016 2016 Pilot’s Handbook Page 25 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

• At least six (6) months operational experience.

Rotor Wing Aircraft

Agriculture and Forestry requires that all pilots meet the competencies outlined in the Helicopter Association of Canada (HAC) endorsed Pilot Competencies for Helicopter Wildfire Operations. Pilots must meet the specific competencies for the following operations:

Wildfire Operations A pilot is competent in: • General Wildfire Operations Knowledge • Mountain Flying (When operating in Southern Grande Prairie, Edson, Rocky Mountain House, and Calgary Forest Areas) • External Load – Short Line (horizontal reference) or Long Line (vertical reference) • Water Bucketing / Tanking • Hover Exit • Confined Area Operations • Low Visibility Flight (Minimum 500 Hours Pilot in Command)

Wildfire Support (exemption for limited competencies, limited to recon, IR aircraft, mission type) A pilot is competent in: • General Wildfire Operations Knowledge • Mountain Flying (When operating in Southern Grande Prairie, Edson, Rocky Mountain House, and Calgary Forest Areas) • External Load – Short Line (horizontal reference) or Long Line (vertical reference) • Confined Area Operations • Low Visibility Flight (Minimum 500 Hours Pilot in Command)

Rappel Operations A pilot is competent in: • General Wildfire Operations Knowledge • Mountain Flying (When operating in Southern Grande Prairie, Edson, Rocky Mountain House, and Calgary Forest Areas) • External Load – Short Line (horizontal reference) or Long Line (vertical reference), • Water Bucketing / Tanking • Class D External Loads • Hover Exit • Confined Area Operations • Low Visibility Flight (Minimum 500 Hours Pilot in Command) • In addition the pilot MUST successfully complete the Wildfire Management rappel operations course and evaluation.

March 2016 2016 Pilot’s Handbook Page 26 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Helitorch Operations A pilot is competent in: • General Wildfire Operations Knowledge • Mountain Flying (When operating in Southern Grande Prairie, Edson, Rocky Mountain House, and Calgary Forest Areas) • External Load – Short Line (horizontal reference) or Long Line (vertical reference) • Water Bucketing / Tanking • Aerial Ignition Device (AID) and Drip Torching • Confined Area Operations • Low Visibility Flight (Minimum 500 Hours Pilot in Command)

Natural Resource Management, Reconnaissance and Surveys A pilot is competent in: • Mountain Flying (When operating in Southern Grande Prairie, Edson, Rocky Mountain House, and Calgary Forest Areas) • Hover Exit • Confined Landing Assessment • Low Visibility Endorsement (Minimum 500 Hours Pilot in Command) • Other competencies as required to complete the mission

Pilot Responsibility Pilots are legally responsible for the safety of passengers and cargo on board the aircraft and have the final say on loading of the aircraft, whether a flight proceeds or is terminated. Pilots must: • File flight plans as required in CARS, • Report all hazards, incidents and accidents to the designated manager as per established times as outlined in the Flight Emergency Section of this handbook • Determine the suitability of weather conditions for a flight, • Determine if and where landings can be made safely, • Ensure maintenance is carried out with minimum impact to department operations, • Monitor assigned radio frequencies while in flight, • Check and report position every 30 minutes or as otherwise planned, • Complete and submit all paperwork at the completion of each work day, • Report unserviceable aircraft immediately to the Forest Area, • Relay immediately any deviations from a flight plan or passenger manifest immediately to the flight watch station, • Ensure all flight and load calculations have been completed as per the requirements of CARS, and • Supervise all refuelling to ensure the procedures are followed, including the established amount, type and quality of fuel used.

Briefing of Passengers by Pilot Pre-flight briefing of passengers and pre-operation briefings of crews is required as part of safe and efficient aircraft operations. It is in the best interest of pilots to ensure that all passengers are briefed before boarding or loading an aircraft.

March 2016 2016 Pilot’s Handbook Page 27 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

The standard for safety is: The safety briefing shall consist of an oral briefing provided by a flight crewmember or by audio or audio-visual means and include the following information as applicable to the aircraft, aircraft configuration, equipment and operation. i) Prior to boarding, procedures for embarking and disembarking when engines are running and rotors are running; ii) When and how carry-on baggage and cargo is to be loaded, secured and unloaded iii) Fastening, unfastening and use of safety belts and safety harnesses, specifying when they must be fastened. iv) The proper positioning of seats for take-off and landing v) The location of normal and emergency exits, how they are marked and how they operate vi) The requirement to obey flight crew instructions vii) The location, access to and use of emergency equipment, including the emergency location transmitter, fire extinguisher, life preservers, life rafts, survival equipment and first aid kit viii) Aircraft evacuation procedures, water ditching procedures, procedures if the aircraft is configured with external fixtures and where applicable to wide bodied rotor wing. The method of egress in the event of a roll-over accident by use of the under seat frame of the traverse cabin seats as ladder for egress.

Where no additional persons have embarked for subsequent take-off on the same day, the take-off briefing may be omitted provided a crewmember has certified that all carry-on baggage and cargo is properly stowed, safety belts and harnesses are properly fastened and seats properly positioned.

The safety briefing need not be provided if the pilot-in-command has ensured that the person has completed a currently valid training program covering the safety briefing requirements for the aircraft.

In addition to the proceeding CARS requirements the following points are to be addressed where applicable: • How to open and close doors and external compartments • How to stow light equipment and loose articles in the area around the aircraft before take-off • Throwing items around rotor wings or moving aircraft will not be tolerated • Appropriate eye, ear and hand protection gear, during operations • Brief ground crew on safety procedures around aircraft • How to protect the nose windows • Smoking restrictions

Briefing of Pilot Briefing Packages A proper briefing package is a key component and shall be used to help ensure a safe and effective operation.

March 2016 2016 Pilot’s Handbook Page 28 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

The Forest Area or Incident Command Team is responsible for preparing briefing packages. The briefing package must be distributed to all personnel directly involved with the operation, including rotor wing pilots on fire, airtanker bases and Air Attack Officers.

Provincial Forest Fire Center (PFFC) The Provincial Dispatcher at PFFC will brief the company at the time the aircraft is hired by PFFC. Points to be covered include: • terms and conditions of hire as per company tariff • minimum standards for hiring, pilot hours, working limits extra flight gear required

Area Fire Centers The Forest Area Duty Officer will brief the company representative or pilot when the aircraft is hired or arrives at the Fire Centre. This briefing may take place at an office or a firebase. Points to be covered are as follows: • Terms and conditions of hire. • Instructions on completing daily flight report. • Use of Wildfire Management radios, including frequencies to be used and procedures. • Use of maps and explanation of Alberta Third System of Survey • Location of fuel caches and fuel dumps within the region, and how to record the amount taken. • Monitoring WM radio frequencies, reporting time of departures (TD’s), time of arrivals (TA's), total flying time (TFT's), and down for night times (DFN) at the end of each day. • Work assignment, projects, and man-up on fire reporting structure. • Floodlight kits are available if required for night servicing (i.e., lights, power plant, and compressor).

Incident Briefing Package A proper briefing package is a key component and should be used to help ensure a safe and effective operation. The briefing package must have a map that is easy to understand, and any changes to the operational plan at the incident must be included in the briefing package and sent out to all parties on a daily basis.

The Forest Area or Incident Command Team is responsible for preparing briefing packages. The briefing package must be distributed to all personnel directly involved with the operation, including rotor-wing pilots on fire, airtanker bases and Air Attack Officers.

The briefing package must have input from the Incident Commander and/or Incident Command Team, and the Air Attack Officer/Air Tactical Group Supervisor. This can be done either through a face-to-face meeting or a conference call.

Once the plan and briefing package have been agreed to, they must be distributed to all the people involved in carrying out the operation. These include: • all pilots on the incident; • the Forest Area offices to brief incoming rotor wing aircraft, airtanker groups, and any transport fixed-wing going to the incident; • all surrounding airtanker bases from which resources may be sent to the incident

March 2016 2016 Pilot’s Handbook Page 29 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

• Air Attack Officer/Air Tactical Group Supervisors to brief all local airtanker groups prior to actual operations and solicit any pilot concerns.

In addition, the Forest Area dispatcher and Incident Command Team must brief all fixed- wing and rotor wing crews prior to them working on the incident. This must be done daily to keep personnel advised of any changes.

Contents of Briefing Package Objectives of the day for: • airtanker group(s) • helitanker(s) • camp and crew moves • burnout operations

Map of the fire showing: • “N” arrow showing magnetic north • all sectors, branches and/or divisions • a grid system allowing all users to identify common points of reference • all facility locations with an identifier • all helispot locations with an identifier • portable retardant mixing/loading site(s) • Areas of special concern; i.e., structure protection, streams, lakes, etc., to avoid dropping retardant and/or foam on or nearby • lakes for skimmers to pick up water • bucket spots • skimming circuit • flight corridors

Rotor wing/fixed-wing resources, listing: • type • call sign or number • assignment

Assigned radio frequencies: • Incident Command Post and call sign • list of applicable Incident Command Personnel radio call signs • air to ground radio frequencies • air to air (tactical) and air advisory (aircraft movement) frequencies designated for the location which the operation may take place • air attack (airtanker/helitanker) bombing frequency(s)

Air space Management plan The Air Space Management Plan should include (but is not limited to): • NOTAM information (i.e. radius in nautical miles around and the ceiling in feet above the incident)

March 2016 2016 Pilot’s Handbook Page 30 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

• Flight corridor(s) and assigned flight altitudes for various types; e.g., service and recon assignments, back/fire burnout operations, rotor wing bucket dip sites, scanning ops, etc. • current updated altimeter setting • air space control zone altitude assignments for: • tactical birddog aircraft • Air Tactical Group Supervisor • airtankers • rotor-wings • other aircraft

Airtanker/helitanker flight corridors and rendezvous points to and from airtanker base(s)/skimmer water sites and/or portable retardant pits, as listed in the following details: • rendezvous points • altitude • map reference and or GPS coordinate • geographic name • bearing and altitude inbound. • bearing and altitude outbound. • skimming circuit • name of pick-up/skimming lake • latitude and longitude of skimming location • map reference • Altitude in circuit

Any specific flight details for movement to and from incident and within the boundaries of a large complex incident: • Facility name (i.e. ICP [Incident Command Post]) • geographic reference • map reference • latitude and longitude location of the facility • Bearing and altitude inbound • Bearing and altitude outbound • to and from base camp to nearest airport for rotor wing and other aircraft • Bearing and altitude inbound to base camp • Bearing and altitude outbound from base camp

To increase traffic separation safety on support action fires, the aircraft’s Global Positioning System unit’s offset capability shall be used. For example, if the route is offset to the right one (1) or two (2) miles, and other pilots do the same, lateral separation from the opposite direction traffic will be from two (2) to four (4) miles, which is still within a normal “airway” width.

Special authority is required for entry into DND Air Weapons Range, Cold Lake. This must be arranged and coordinated through the Lac La Biche duty officer. The duty officer will inform the pilot of the approved penetration point and any restrictions to be observed.

March 2016 2016 Pilot’s Handbook Page 31 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Radio Use, Airspace Management, and Flight Following

The Forest Protection Radio Guide (FP 183) lists all Forest Area frequencies, stations, channels and VHF / FM and VHF/AM frequency allocations. The most current version will be attached to this document and sent to companies on an annual basis. A pocket size copy of the Radio Guide is available upon request at Forest Area offices. Aircraft are expected to arrive for hire with all applicable radio frequencies programmed into their radio. Every pilot must ensure they understand the wildfire management radio procedures prior to commencement of the flight. Pilots of rotor and fixed wing aircraft hired on casual charter for use on fires or project work must be briefed thoroughly on Wildfire Management policies and procedures pertaining to radio communications prior to commencement of the flight. If any aircraft loses the ability to communicate with a designated radio station via air-to-air or air-to-ground due to a failure of the on-board radio, the aircraft is considered unserviceable and shall be removed from service until the radios are operational.

FM Radio Power Settings: VHF FM radios are to be operated on LO [1 watt] transmit power. This is required to minimize opening repeaters. If HI [10 watt] required, reselect radio transmit power to LO power after use.

Class F Airspace Management The Wildfire Management Branch has been assigned a number of VHF-AM frequencies from Industry Canada. The allocation of these frequencies is managed by the communication section of Forest Operations. The air attack program has been given exclusive use of a number of these which have been assigned to the 8 air tanker groups. Five (5) frequencies have been allocated to be used for initial attack air to air advisory. The following are the radio frequencies to be used for air advisory: • 129.800 MHZ (Primary) • 128.950 MHZ (Secondary) • 131.850 MHZ (Alternate) • 130.750 MHZ (Alternate), North of 52° only • 130.175 MHZ (Alternate), North of 53°only

The use of the airspace management frequencies is restricted to aircraft flight coordination / movement only. All other communications (i.e. to discuss tactics, logistics, etc.) are to be done on the assigned VHF FM frequency (Fire Net and / or Fire Line frequencies).

The Birddog team [Birddog Pilot and Air Attack Officer] or ATGS act as the airspace manager over an incident. The Air Attack Officer will issue air space management instructions to non-Airtanker aircraft, on an established air advisory frequency. Management of an Airtanker aircraft in the zone will be performed over an assigned bombing frequency.

When two (2) Birddog aircraft are on a fire, one Birddog may assume the Air Tactical Group Supervisor (ATGS) role. The ATGS will be identified as “Air Attack” and either the Wildfire number or a geographical identifier. For example: Air Attack Fire 31 or Round Hill Air Attack. This resource will not use their birddog aircraft identification number / call sign.

March 2016 2016 Pilot’s Handbook Page 32 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

• The operational birddog will use their birddog call sign (i.e. Birddog 55).

Outside Class F Airspace (Transiting to and from the fire) • All aircraft will monitor the VFR mandatory frequency of 126.7 and the primary initial attack frequency of 129.8 • Ensure transponder is on and squawking 1200 codeAll aircraft will follow visual flight regulations including the required cruising altitudes o Westerly track (180-360 deg), maintain even altitude +500 feet o Easterly track (000-180 deg), maintain odd altitude +500 feet

To increase traffic separation safety on support action fires, the aircraft’s Global Positioning System unit’s offset capability shall be used. For example, if the route is offset to the right one (1) or two (2) miles, and other pilots do the same, lateral separation from the opposite direction traffic will be from two (2) to four (4) miles, which is still within a normal “airway” width.

It is standard procedure and required for all aircraft to contact the airspace manager (if activated)

Approaching Class F Airspace (Approaching the fire) • If there is NO airspace manager (Birddog or ATGS), all aircraft will call 5 minutes back on the primary initial attack air advisory frequency 129.8 o If no response, proceed to 2 minutes back o If still no response and there is a known aircraft in the zone, DO NOT proceed inbound until communications are established • All aircraft operating in the un-managed fire airspace will maintain their own separation using 129.8

• If an airspace manager (Birddog or ATGS), is activated, all aircraft must call them on the assigned air advisory frequency (established by the birddog or ATGS): o When approaching Class F airspace 5 minutes back o If no response, proceed to 2 minutes back If still no response and there is a known aircraft in the zone, DO NOT proceed inbound until communications are established

The Airspace Manager (Birddog or ATGS) will Require: o Your aircraft registration o Your altitude, position and direction of approach o Your intensions Example:

“Birddog 132, this is GYHB on air advisory I am 5 minutes back from the west at 3500 feet I would like to drop off my crew off at the tail of the fire”

• The birddog will provide: o an altimeter setting o clearance and/or holding instructions

March 2016 2016 Pilot’s Handbook Page 33 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

When a fire transitions from Initial Attack to sustained action, the Forest Area will determine the requirement to assign a sustained action air advisory frequency.

Flight Plans and Flight Monitoring Flight Following and Flight Plans All aircraft flying for the Department and non-department flights carrying Department employees on related business (oil, gas and timber inspections where company provides aircraft) must file a Flight Plan or Flight Itinerary as follows:

A “Flight Itinerary with Flight Following Radio Watch”, or A “Flight Itinerary without Flight Following Radio Watch”, or NAV Canada - a Visual Flight Rules (VFR) or Instrument Flight Rules (IFR) flight plan. Any flight designated as IFR must file an IFR flight plan with NAV Canada.

When flying within a Forestry Program Area, the appropriate Forest Area fire centre radio room will be open; it is the required method for flight following for flights within or between Areas. Exceptions are permitted for high altitude IR scanning flights. Alterations in the planned mission or itinerary must be immediately conveyed to the Flight Watch station / person.

All aircraft operating under the jurisdiction of the Department under Instrument Flight Rules (IFR) must file a flight plan with NAV Canada. Refer to Canadian Air Regulations.

The above does not apply to regular “Airline Scheduled” flights (Air Canada, WestJet etc.)

Flight Itinerary with Flight Following Radio Watch • Information passed to radio watch stations shall include estimated arrival and departure times, flight path, planned stops and a complete passenger manifest. • Originating and check-in stations must keep all other stations advised of changes to the passenger manifest or estimated arrival times. • The originating office must provide the pilot with the call sign or contact person and the method of contact for station enroute. • The pilot in command shall check in at 30 minute intervals to the appropriate radio station, unless alternate check-in intervals have been arranged in advance. If the itinerary changes between 30 minute check-ins, the pilot must advise the appropriate radio station as soon as possible. • Employees who are providing radio watch must be aware of the missing aircraft procedures within the Emergency Incident Response Procedures and implement them if the expected check-in time or estimated arrival time is exceeded by 30 minutes. • Radio stations providing coverage for a flight must remain open until the flight is officially handed off to the next station enroute. • Any person providing radio watch for an aircraft shall initiate radio contact with the aircraft; o If the estimated arrival time has been exceeded by 30 minutes, or o When the aircraft has not checked in at the prescribed 30 minute interval, or

March 2016 2016 Pilot’s Handbook Page 34 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

o When longer check-in periods have been arranged and the check-in time is exceeded by, 50%, or 30 minutes whichever is shorter, or o Any time any aircraft makes any type of distress call. • A person receiving information regarding a flight must forward the information to the radio room which the flight originated from or which is responsible for closing the flight itinerary, whichever is appropriate.

All written station logs shall be retained for a period of at least 2 years and must be made available upon request.

Flight Itinerary without Flight Following Radio Watch

This type of flight watch is not encouraged. It is to be used only when a staffed radio room is not available or the aircraft is not equipped to communicate with the radio room.

• The person initiating the flight must designate a person to be responsible for their flight itinerary and closing the flight plan. This includes providing them with: departure time, flight path, planned stops and a manifest of all passengers and return time. • The designated person must remain available until the flight is closed. • Upon completion of the flight, the flight initiator must contact the designated person to close the flight plan. • The designated person must be aware of the missing aircraft procedures within the Emergency Incident Response Procedures and implement them if the estimated arrival time is exceeded by 30 minutes. The local Wildfire Management Duty Officer can assist with this.

Pilots must be advised of the name and means of contacting the person responsible for closing the flight itinerary. This person must remain available until the flight is closed. The pilot in command shall, upon completion of the flight, contact the person responsible for closing the flight plan within 30 minutes of the intended arrival time of the aircraft.

When individuals responsible for closing the flight plan believe the aircraft is missing, and has not closed the flight itinerary within 30 minutes of its planned arrival time, they must initiate the procedure for a Missing Aircraft as detailed in the Emergency Incident Response Procedures. Operation Safety and Procedures

Flight Management General Restrictions and Requirements The following restrictions/requirements apply to all flights (except regular “Airline Scheduled” flights (air Canada, WestJet, etc.) • No fixed wing or rotor wing reconnaissance flights in temperatures below -30 oC. • No one shall operate an aircraft, or direct an aircraft to be operated, in an unsafe manner. • Any person on doctor prescribed medication will ensure they have sufficient medication on their person for 3 days.

March 2016 2016 Pilot’s Handbook Page 35 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

• Based on the nature of the activity, environment and assessed risks, individuals shall be attired to spend a minimum of 24 hours in the “bush”. • A briefing will be held between the aircrew and passenger(s) describing the nature of the flight and expectations of the aircrew to ensure that the mission and expectations are clearly understood. • The minimum Transport Canada survival equipment onboard the aircraft.

Pilot’s Duty Day A pilot’s duty day is restricted by the Canadian Air Regulations. This duty period is (14) fourteen hours in any 24 consecutive hours.

A pilot’s duty day starts when a pilot: • Reports for a flight, • Reports for standby that has a reporting time of one hour or less, • Performs any duty required by the company, or • Performs any duty designated by the Minister of Transport.

A pilot’s duty day ends when: • The engine is turned off at the end of the final flight, • Any required paperwork is completed, • Any pilot performed maintenance is completed, • At the end of a predetermined standby period, whichever is later.

Note: Travel, food, and hygiene are not included in the duty day.

Mandatory Rest Periods All pilots must have, excluding meal breaks, a minimum of eight (8) hours of prone rest between the end of one (1) duty period and the start of the next.

Before starting the next duty day, the pilot must be given sufficient time to allow for 8 hours of prone rest, travel to and from the workplace, meal breaks and personal hygiene.

Flight Hour Limitations Wildfire Management’s standard maximum daily flying times are as follows:

Maximum Daily Flight Time To ensure safety, the Department has established a maximum of ten (10) hours any pilot may fly within their duty period. This requirement was implemented to reduce fatigue and ensure every pilot has the required nutrition and personal breaks each day. The Department may add additional restrictions for ongoing operations to reduce pilot fatigue and ensure an increased level of safety during operations.

Rotor wing – Suppression and Presuppression Assignments • Ten hours maximum for the first three (3) days of continuous activity, and • Eight (8) hours maximum for every consecutive day thereafter.

March 2016 2016 Pilot’s Handbook Page 36 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

• The Forest Area Duty Officer, Incident Commander or the Air Operations Branch Director may allow a pilot who has been flying to start the first of his ten-hour days providing: o Pilot has been on continuous ‘light duty’ such as man-up, day basing, or flying patrols, and o In the previous three (3) days pilot has flown less than four (4) hours per day.

To reset to a ten-hour day the pilot must not fly for a 24-hour period.

Rotor wing – General Duty Assignment Pilots involved in moving crews from airport to airport or for out-of-province basing, may fly a maximum of 10 hours per day.

To reduce fatigue, the Air Operations Branch Director, Forest Area Duty Officer or their designate must monitor pilot flying times and when required ask a company to rotate flight crew or change aircraft assignments.

To ensure the maximum numbers of aircraft are available during peak workloads, daily aircraft availability should be scheduled against hours of work limitations. Where practical, scheduling should also provide for rotor wing aircraft maintenance to be performed during daylight hours.

Rotor wing – Infrared Scanning Aircraft assigned to infrared scanning operations will work within the normal 14 hr. duty day period only.

Fixed-Wing Airtankers – Initial Attack Fires All airtanker types can fly a maximum of ten (10) hours, per day, per airtanker (wheels roll to wheels stop) on initial attack fires, based on the pilot’s duty day.

Fixed-Wing Airtankers – Support Action Fires • All airtanker types can fly a maximum of ten (10) hours, per airtanker (wheels roll to wheels stop), for the first day of support action. • All airtanker types can fly a maximum of eight (8) hours, per day, per airtanker (wheels roll to wheels stop), while on support action, based on the pilot’s duty day. • If a flight crew has been actively flying on initial attack immediately prior to being assigned to support action, the Air Attack Officer and Group Captain shall be consulted to determine if the maximums noted should be reduced due to cumulative fatigue. • If anticipated action is expected to exceed duty limitations, additional pilots, engineers and an Air Attack Officer shall be requested to double-crew the aircraft. This normally applies to, but is not limited to, the CL-215s, when on support action.

March 2016 2016 Pilot’s Handbook Page 37 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Fixed-Wing Casual Charter and Fixed-Wing Spray Aircraft All other types of fixed-wing casual charter and fixed-wing spray aircraft can fly a maximum of ten (10) hours, per day (wheels roll to wheels stop), based on the pilot’s duty day.

Low Level Operations (<500 feet AGL) The following are operating procedures for activities which do not have a specific set of procedures similar to those developed for Fire Bombing, Rappel, Aerial Ignition and Hover Exit.

General The company, pilot and aircraft will be qualified by Transport Canada for 702 Aerial Work. Flight crew are to be fully engaged in “flying the aircraft” and not be distracted by other work being done. Wherever possible, Agriculture and Forestry staff should operate radios on Agriculture and Forestry assigned frequencies, including telemetry receivers. The pilot can monitor these radios if the cockpit workload permits. Except were specifically permitted in Canadian Air Regulations sections 602.12-602.16, no flights over the built up area of a community shall be conducted at altitudes below 1000 feet AGL. A Hazard and Risk Assessment is to be done for the specific task undertaken requiring low level operations including the need for the flight and alternate means of accomplishing the task identified.

Rotor Wing The flight profile should remain at an altitude of at least 300 feet above ground level (AGL) and remain in the safe operating areas of the “Height / Velocity” (HV) chart specific to the rotor wing in use. If the mission requires the flight profile to go below 300 feet AGL or into the “unsafe” portion of the Height Velocity (HV) curve, the exposure time is to be minimized and: • Only essential crew are allowed on the aircraft. • If working over open water, the pilot must brief Agriculture and Forestry personnel on the specific emergency procedures to follow, including ditching procedures and egress from the aircraft. • A Hazard and Risk analysis shall be completed to identify any extra safety equipment and/or training required by Agriculture and Forestry staff or contractors (e.g. flight helmets and flotation devices, water egress training, etc.). • Winds must be less than 75 km/hr or wind gusts less than 30 km/hr. • A power check must be done prior to entering the Height Velocity curve. There shall be sufficient torque to maintain the aircraft in a hover for 5 minutes without exceeding the manufacturer’s temperature or torque limits and have full tail rotor authority.

Fixed Wing With the exception of a wings level pass, the flight profile shall remain at an altitude of at least 300 feet AGL. The maximum angle of bank while operating below 500 feet AGL shall be 30 degrees. Other than take offs and landings, at no time shall the flight profile go below the adjacent tree canopy. In level flight, the indicated forward airspeed must not drop below 1.3 times the configured stall speed. If the aircraft will be in a turn, the airspeed must be maintained at 1.5 times the stall speed or higher. March 2016 2016 Pilot’s Handbook Page 38 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Standard Airmanship – Cruising Altitudes

All aircraft operating within the fire zone will be assigned corridors and approach/departure altitudes by the airspace controller. Outside the control zone the aircraft are required to cruise at the appropriate Visual Flight Regulation (VFR) altitudes listed below:

VFR Cruising Altitudes

Heading Altitude Westerly Track (180o - 359o) Even Altitude + 500ft. Easterly Track (000o – 179o) Odd Altitude + 500ft. Aircraft can cruise at any altitude from ground level to 3,000ft. AGL.

Flight Crew Alert Statuses Flight crew alert statuses are each set for following day by the Forest Area Duty Officer after the afternoon weather forecast.

The criteria to determine these times are: • Location of aircraft, • Current fire hazard, • Risk potential, and • Type of aircraft.

The Forest Area Duty Officer is responsible for setting and passing the alert status for all suppression and presuppression resources.

Rotor Wing The alert status for presuppression rotor wing aircraft is: • Five (5) minutes (minimum departure time for the A-Star and Medium type rotor wing), • Ten (10) minutes, • Thirty (30) minutes, • Sixty (60) minutes, and • Project Status (PS).

Airtankers Airtanker aircraft alerts status will be set by the Provincial Aircraft Coordinator in consultation with the Forest Area Duty Officer as follows:

Red Personnel must be on base for the specified standby period and aircraft and air crew must be ready for immediate dispatch. Birddog aircraft must be wheels roll within 5 minutes of dispatch.

Yellow Personnel must be available to depart within 30 minutes of dispatch notification. Birddog aircraft must be wheels roll within 30 minutes of dispatch. March 2016 2016 Pilot’s Handbook Page 39 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Blue Personnel must be available to depart within one-point-one (1.1) hours of dispatch notification. Birddog aircraft must be wheels roll within 1.1 hours of dispatch.

If the group was advised of a Blue alert status: • at least twelve (12) hours in advance of the start of the alert, and • the air tanker group does not fly, and • the alert is not increased, the day will be considered a “Day Free from Duty”.

Time free from duty is required under Transport Canada – CARS. Three (3) periods of 24 consecutive hours free from duty within 30 consecutive days and 13 days free from duty within 90 consecutive days are required. This is applied on a moving calendar basis (from present calendar day, back 30 days previous (June 12 to May 14 = 30 days)). During this thirty-day period, three (3) days must be “free from duty”. The days shall be scheduled at least twelve (12) hours in advance and the flight crew must be advised and are not expected to be assigned to flight duty.

Green Day The airtanker group is off duty and can be away from the base.

• Must be scheduled at least 12 hours in advance and flight crews advised. • Airtanker group shall be off duty for designated period. • Green Days ‘DO’ count toward the total “Days Free from Duty”. • Designation is restricted to periods of general rain and low hazard throughout the province. • Green Days are an exception, rather than a rule, and will be considered only when hazards are very low and no threat of immediate weather changes or other needs exist.

Green Days are used to help improve group morale. By giving flight crews the opportunity to be away from standby status without the need for immediate recall, they can experience a total break from fire operations.

The decision to grant Green Days rests with the Provincial Forest Fire Centre Duty Officer. A thorough review of the potential fire danger, including anticipated needs, both provincially and nationally, and consultation with all parties concerned is needed before Green Days can be considered. Green Days would be rotated to ensure one (1) particular group does not remain in a low hazard area over a long period, while other groups continue to work long duty days on standby.

Example of assigning a green day to an airtanker group:

July 6 1600 hrs. Green Day status declared, as per Preparedness Planning System. 2000 hrs. Stand down for the day. July 7 Off (Green Day) July 8 1000 hrs. Stand to as declared on standby times issued on July 6, 1600 hrs.

March 2016 2016 Pilot’s Handbook Page 40 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Total time away: 38 hours

When weather conditions permit, Green Days can be extended to two (2) full days.

Day Base Aircraft (rotor wing and airtankers) are moved to an alternate base for the day. This is usually done after 1100 hours for anticipated fire action or support. Normally the aircraft will return to their home base unless prevented by fire action or weather conditions.

Passenger/Cargo Manifest (FP249) A written manifest including the names of all persons on board the aircraft is required for every flight conducted by the Department. The originating radio room or person responsible for initiating flight following, until the flight is completed, must retain a copy of the manifest information.

Rotor Wing Load Calculations The purpose of carrying out rotor-wing aircraft load calculations is to ensure that the aircraft is capable of carrying a specified load to an identified elevation at a given density altitude. The load calculation must be completed daily for all rotor-wing flights prior to the start of operations. For repetitive flights, one calculation is valid between like points of similar elevation as long as weather conditions do not change, and loads do not exceed that which was authorized by the calculation for the initial flight.

Responsibility for completion of load calculations is as follows:

Pilot Responsibilities The pilot is responsible for completing the load calculation correctly using proper performance chart information as per the Company’s Operation Manual, Canadian Aviation regulations (CARS) and the Commercial Air Service Standards. The pilot is responsible for computing the allowable payload. The pilot must enter the following weights (in pounds) on the FP249 Passenger/Cargo Manifest for any flight carrying Departmental employees: • Maximum internal gross weight of the aircraft • Aircraft empty operational weight • Pilot and personal kit weight • Fuel Weight • Remaining available payload Note: Empty operational weight includes the complete equipped weight of the aircraft with no fuel on board. This includes but is not limited to the weight of the bucket, longline, survival kit, refuelling gear, radios, etc. Note: Remaining available payload must be based on aircraft performance, the least favorable predicted density altitude based on the highest temperature and operational altitude to be encountered for the day, and comply with weight and balance limits. The pilot must sign and date the FP249 Passenger/Cargo Manifest to certify that the information provided is complete and accurate to the best of their knowledge. The pilot shall check, or be informed of, any subsequent passenger/cargo manifested weights completed under the initial load calculation to ensure allowable payloads are not exceeded.

March 2016 2016 Pilot’s Handbook Page 41 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Government Representative Responsibilities The Agriculture and Forestry representative responsible for a flight (e.g. Crew leader, Loadmaster, Biologist, Forest/ Fish and Wildlife Officer, etc.), is responsible for providing the pilot with a complete GOA passenger / cargo (including external sling net loads) manifest (FP249) including accurate weights, and advising the pilot of all dangerous goods being carried.

For flights departing from a permanent facility, (examples Office, Warehouse, Hangar, Airtanker Base, Lookout or Primary Fire Base) passengers and cargo will be weighed, on a scale, at the beginning of the day or first flight of the day. Subsequent flights will have weights adjusted for changes resulting in an increased payload such as wet hose, additional cargo, or additional or switching of passenger numbers, etc. The passenger manifest and total GOA payload on board the aircraft is to be conveyed to the originating radio room or person responsible for initiating flight following. In addition a Passenger / Cargo Manifest / Weights (FP249) form, with all weights recorded must be retained at the facility for a period of at least 60 days.

For flights originating from remote location (example, MPB crews, surveyors, Crew pick up on Type 3 and 4 fires, from the “line” on Type 1 and 2 incidents) passengers will provide to the pilot their most recent “seat” weight that was measured on a weigh scale. Cargo maybe estimated using weights from the pilot’s handbook of actual weights recorded on the equipment. The passenger manifest and total GOA payload on board the aircraft is to be conveyed to the radio room or person providing flight following

For flights on Type 1 and 2 incidents, departing from a helibase or helispot associated with base camp or a line camp, all passengers and cargo will be weighed on a scale and information provided to the pilot on FP249. The passenger manifest and total GOA payload on board the aircraft is to be conveyed to the radio room for the incident. In addition a Passenger / Cargo Manifest / Weights (FP249) form, with all weights recorded must be retained at the helibase or line camp and provided to the Documentation unit within 24 hours.

Refuelling Operations All personnel responsible for transporting aviation fuels and refuelling aircraft must realize the safety of the aircraft and personnel depends on the responsible individual’s ability to deliver the correct type and grade of uncontaminated fuel to the aircraft. The possibility of human error must be avoided by providing adequate fuelling facilities, safe operating procedures, and adequately trained personnel using the latest equipment.

The following procedures must be followed during refuelling operations: • Smoking on any airport ramp is prohibited during refuelling operations. • Open flames on aircraft fuel servicing ramps, aprons or any other fuelling operation site where aircraft fuelling is being carried out by or on behalf of Wildfire Management, or within 50 feet (15 meters) of any portable or field fuelling operation and fuelling equipment is prohibited. • No person operating an aircraft shall permit it to be refuelled if passengers are on board, embarking or disembarking. • During refuelling operations, the proper type and size of fire extinguishers must be available for use close to the operation. March 2016 2016 Pilot’s Handbook Page 42 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

• The aircraft engines must either be shut down or the approved hot refuelling procedures followed. • The pilot-in-command must ensure the aircraft has the appropriate fuel and the required amount for the planned flight. • Operating personnel are to follow the guidelines listed below: • Never leave any fuel nozzle unattended. • Never tie or wedge the nozzle trigger in an open position. • Full attention is to be devoted to the refuelling operation. • Check the amount of fuel in the tank frequently to prevent overfilling. • Either hand or power-operated pumps shall be used when aircraft are refuelled from drums and pouring or gravity flow is not permitted. • Avoid kinks and short loops in the fuelling hose. • As soon as leakage or spillage from the fuel-servicing equipment is noted, stop the flow of fuel immediately. • Fuelling operations shall be suspended where there are lightning flashes in the immediate vicinity of the fuelling operation site.

Refuelling aircraft can be carried out from: • Commercial outlets, • Wildfire Management underground tanks, • Wildfire Management bowsers, • Contract portable fuelling systems/bowsers for field operations, or • Wildfire Management drums (purchased fuel).

Hot refuelling aircraft on Wildfire Management projects will be allowed only if: • There are no passengers on board, embarking or disembarking, • The pilot’s seat must be occupied by a person who is competent in controlling the aircraft, and • Refuelling is carried out by a trained company engineer and/or a person who is trained and certified in refuelling aircraft as per the CAN/CSA Standard for Storage, Handling and Dispensing Fuels at Aerodromes. • a third person is present to act as a visual link between the pilot and refueller during hot refuelling operations, rotor wing with a filler neck for the fuel tank located on the opposite side from the pilot must be shut down and the pilot must exit the machine to supervise the refuelling. • Agriculture and Forestry does not pay flight time for hot refuelling

Although Wildfire Management makes every attempt to keep fuel clean and current, pilots should always check the fuel to make sure it is the appropriate type for the aircraft and is free from foreign material. Wildfire Management personnel have no authority to refill drums from bulk aviation fuel sources. Due to the liabilities involved, Wildfire Management will not do this for any operations. Pilots can refuse to accept fuel from unsealed or improperly sealed drums and damaged drums. Pilots may use fuel from their own source if requested to do so by the Forest Area Duty Officer or Designate, fuel amounts must be recorded on the flight report. Wildfire Management will reimburse fuel charges incurred, providing supporting documentation is attached (legitimate invoices).

March 2016 2016 Pilot’s Handbook Page 43 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Fuel spills are often the result of improper or careless operation of fuelling equipment and poor maintenance of the mechanical fuelling equipment. To prevent fuel spillage, caution is required on the part of every person responsible for fuelling equipment.

Note: As per the current Alberta Fire Code, when the loss of a flammable liquid or combustible liquid occurs from a spill or leak, the operator shall ensure that: • Appropriate action is taken as required to recover escaped liquid, prevent it from escaping the site where possible, and to remove or treat the contaminated soil. • The fire department and the authority having jurisdiction are notified if the quantity of liquid spilled or leaked o Exceeds 50 litres in aggregate, or o Is sufficient to cause sheen on nearby surface water.

Rotor Wing Sling Loads Personal gear and small or lightweight items that may be blown from or fall through sling webbing shall not be transported in a sling.

Sling loads shall not to be lifted from or onto a vehicle.

Items of high value (garden tractors, quads) can be carried in a sling, if no other “in cabin” transport is available and rotor wing is of an adequate size and capacity to safely carry item.

Long Line Use (Rotor wing) Long line operations are very unique and can be very cost effective. They can also provide an extra measure of safety to an operation. When conducting long line operations consider the following: • In most helicopters, it is mandatory that the operation be conducted from the left front seat. This requires the installation of dual controls and a door that is equipped with critical engine gauges. • The conversion of a rotor wing in or out of long lining configuration takes time. Please consult with the pilot and aircraft engineer for exact times. • Once the dual controls have been installed, it is at the pilot’s discretion to allow passengers to occupy the front seats. ONLY qualified personnel are permitted in the front seats. This may limit the quick and alternate use of the aircraft

Ground Running of Engines during Bucketing or Sling Operations Another person must be present to act as loadmaster for the pilot, or the pilot must shut down the rotor wing before he exits the machine to do the hook up/release himself, when the following situations occur:

• The hook up and release takes place at a site where there are people present who are not involved in the operation, • There are other helicopters using the same site for landings and departures at the same time, and

March 2016 2016 Pilot’s Handbook Page 44 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

• The operation occurs near Wildfire Management facilities, both permanent and temporary (line and fire base camps). Aircraft on Wildfire Management projects will only be allowed to carry out load hook up and release operations with the engine running and the pilot’s seat unoccupied when none of the above noted situations occur.

Flights with Passengers and External Loads External loads (sling or other) are governed by the Canadian Air Regulations. Carrying passengers is permitted only under the following five (5) scenarios.

Rappel Operations The leader (spotter) is permitted on board the aircraft to deploy the emergency retrieval system and to coordinate bucket operations. Once the forward spread of the fire has been stopped and there is a very low risk in which the emergency retrieval system would be deployed, the spotter is then deployed to the fire.

Bucket Operations For initial attack or sustained action, Incident Command personnel on board medium rotor wing aircraft may be permitted only during bucket operations.

The pilot and company must be certified to conduct this operation as per CARS section 702.16 and the CARS Standard 722.20(2). When Agriculture and Forestry staff are onboard an aircraft during bucket operations, they are required to wear a personal flotation device.

Wildfire Operations Air operators may carry persons other than the flight crew if: • The operator is authorized to do so in their Air Operation Certificate, • The person has received a safety briefing by the pilot as per the CARS Standard 722.23, and • The person being carried is involved in wildfire suppression activities.

Aerial Ignition on Wildfires Aerial ignition operations shall be conducted with an intermediate category rotor wing or larger (only the Airbus EC 120 in the light category) if the Aerial Ignition Specialist is onboard. If the Aerial Ignition Specialist is not onboard, the minimum rotor wing size for this operation shall be a Bell 206BIII or equivalent.

Operations shall be conducted in accordance with the Ignition Manual. The AS 350B3, Bell 206 L4, Bell 407 and EC130 rotor wing have been approved for use if operations include both an Aerial Ignition Specialist and trainee. The AS 350B2, FX2, and D2 are conditionally approved if no alternate is available and the fuel load is reduced.

Local conditions and the environment around the fire must be considered to assess the suitability of any aircraft while conducting this operation. If out-of-province personnel are filling the role as the Aerial Ignition Specialist then an additional aircraft may be required for this operation. A number of jurisdictions will not permit their staff to fly in the heli-torch equipped rotor wing.

March 2016 2016 Pilot’s Handbook Page 45 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Transporting Wildlife Department staff is considered essential crew if they are required to monitor the condition of an animal during flight.

Entering or Leaving a Hovering Rotor Wing in Flight Exiting and boarding from a rotor wing in a hover can be accomplished safely providing the personnel are trained in the manoeuvre. The movement of personnel and equipment must be pre-planned and practised. Personnel must have an appreciation of why these moves are made and what the results and effects of movement on a hovering rotor wing aircraft.

The PFFC Manager of Aviation and Geomatics is the approving authority for the Hover Exit Program. The Wildfire Operations Officer will assign training co-ordinator(s) to ensure the training is carried out as per the training manual, that all trained personnel have proof of training, and that their proficiency training is carried out and documented.

Hover exit training will be part of the regular training for Rappel, Helitack and Unit Crews. The Forest Area Wildfire Operations Officer must approve other forestry personnel who require training. Only a certified instructor can carry out basic hover-exit training. All certified hover exit personnel must maintain certification as outlined in the Hover Exit/Freeboard Training Guide.

Transport Canada (Canadian Aviation Regulations Part VII, Sections 702.19, 702.21, and Part VI, Sections 602.15, 602.17 and 602.25) (Sec. 722.19 Commercial Air Service Standards) allows rotor wing aircraft companies to apply for authorization to exit/board persons from rotor wing while in flight.

The CIFFC Manual defines a hover as:

A hover is a state in which the helicopter is under power and the pilot must manipulate the flight controls to maintain a stable attitude. This could be free of, or in partial contact with a grounded surface.

For the purpose of Wildfire Management operations, a hover exit is only permitted if it allows the person performing the hover exit to have contact with both the ground and the rotor wing.

Emergency Rotor Wing Boarding in a Hover The reloading of personnel and equipment into a hovering Rotor wing is considered to be an exception rather than a standard practice. There is a requirement to train Wildfire Management personnel for this manoeuvre not only for the expediency of the firefighting operation but for swamp and deep snow pick-ups.

Hover loading of personnel and equipment may be authorized providing: • Personnel have been trained in the manoeuvre. • The pilot and crew leader agree on the sequence of events. • The site is acceptable to the pilot. • The equipment must be bundled/packaged in an acceptable manner and capable of hand-to-hand transfer if it is to occupy cabin space. March 2016 2016 Pilot’s Handbook Page 46 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

• The rotor wing must be capable of exiting the pick-up area with an out-of-ground effect power reserve with the anticipated load.

The pick-up site will be prepared to provide rotor clearances for the rotor wing and sure footing for the personnel.

Personnel and pre-packed equipment will be pre-sited before rotor wing arrival and equipment is to be secured.

Reloading sequences are the reverse order of exit. Emphasis will be on the smooth initial transfer of weight on the skid. Smooth crew movement control is vital as the weight of the aircraft increases. Crew leader (first in) will establish pilot/crew contact as soon as possible after boarding and will control the reloading by use of hand signals.

Hover Exit Conditions and Limitations • Conducted only by trained personnel. • Conducted only where the trained personnel can transfer their weight from the rotor wing to the ground smoothly and gradually, rather than jump or drop to the ground. • Hover exit to be conducted with an acceptable power and fuel reserve required maintaining hover out-of ground effect at the set-out/pick-up site. • Must have “hot” (hands free) intercom capability between pilot and crew leader. • Must have doors, which either can be removed prior to exit or safely opened in flight. • Skids and exiting area must be unobstructed. • Sliding/folding doors and removable doorposts must be secured.

Rotor Wing Aircraft Company Compliance and Pilot Qualifications The rotor wing aircraft offering this service to Wildfire Management will: • Produce an approved amendment to their Air Operations Manual if requested by the Department. • Provide pilot briefings and approve personnel exiting/boarding. • Provide pilot training in accordance with Sec. 722.76 Commercial Air Service Standards, and to an acceptable Wildfire Management standard. • Ensure that the rotor wing is capable of being operated within the centre-of-gravity limits for the most extreme case in the hover exit/enter manoeuvre. • Ensure the rotor wing is capable of a safe out-of-ground effect power reserve at the set-out/pick-up site, with on-board or anticipated loads. • Company must be on a Wildfire Management approved list. • Pilot must provide proof of Transport Canada certification upon request. • The pilot must demonstrate the ability to carry out personnel and equipment moves to Wildfire Management satisfaction.

Safety Considerations for Working in the Cold Lake Air Weapons Range (CLAWR) The Cold Lake Air Weapons Range (CLAWR) poses some unique hazards. This Area is not hunted and has had numerous "problem" bears released over the years. You can expect a higher frequency of bear encounters here.

March 2016 2016 Pilot’s Handbook Page 47 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

There might be large amounts of small, fast aircraft (jets) creating air traffic problems. It is an active weapons range which might have: • Unexploded ordnance (bombs and rockets), • Practice bombs that may contain acid marking charges - used to generate smoke to see where the practice round landed, • Lasers - CLAWR often has pilots using lasers mounted to the aircraft for targeting with laser-guided munitions. These lasers are powerful enough to cause blindness, or • Radar emitters - used to simulate enemy tracking or targeting radars. These give off large levels of radiation in the immediate area of the emitter.

Contact the Lac La Biche Office before entry. If possible, a CLAWR grid map should be obtained. The Lac La Biche Duty Officer will contact range control for access permission. Under no circumstances are aircraft to proceed into the range without clearance. Upon clearance by the duty officer, the pilot will contact the tower at Cold Lake. The Lac La Biche radio room will supply a current frequency. At the north end of the range, contact may be difficult. It may be necessary to climb up several thousand feet to establish contact. If you are unable to contact the tower, contact the Lac La Biche Radio Room and they will notify the tower by phone. Do not proceed into the CLAWR until you have confirmed that Cold Lake Tower has been notified.

FIRE GRID Quadrants & Corridors

112 15 111 45 111 15 110 45 110 15 109 45 109 15 108 45 108 15 107 45 107 15 112 30 W112 111 30 W111 110 30 W110 109 30 W109 108 30 W108 107 30 W107 N5540 N5540

55 30 Y1 Z1 A1 B1 C1 D1 E1 F1 G1 H1 I1 55 30

N5520 N5520

55 10 Y2 Z2 A2 B2 C2 D2 E2 F2 G2 H2 I2 55 10

N55 N55

54 50 Y3 Z3 A3 B3 C3 D3 E3 F3 G3 H3 I3 54 50

N5440 N5440

54 30 Y4 Z4 A4 B4 C4 D4 E4 F4 G4 H4 I4 54 30

N5420 N5420 112 30 W112 111 30 W111 110 30 W110 109 30 W109 108 30 W108 107 30 W107 112 15 111 45 111 15 110 45 110 15 109 45 109 15 108 45 108 15 107 45 107 15

Alberta Fort McMurray Oil Sands Class E Airspaces The development of the oil sands in North-eastern Alberta has resulted in increased air traffic in the areas North and South of Fort McMurray. NAV CANADA completed aeronautical studies to review the communication and airspace requirement s for areas

March 2016 2016 Pilot’s Handbook Page 48 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

north and south of Fort McMurray. The result of the studies was the establishment of two Class E airspaces known as North Oil Sands ATF Area and South Athabasca Oil Sands.

North Oilsands ATF Area The North Oilsands ATF Area encompasses three aerodromes in relatively close proximity to each other – Fort Mackay/Horizon, Fort Mackay/Firebag and Fort Murray/Mildred Lake. The North Oil Sands air traffic advisory frequency 123.5 MHz is to be used before entering and within the Class E airspace. See the current Canadian Flight Supplement for full details.

South Athabasca Oil Sands Area The South Athabasca Oil Sands Area encompasses four aerodromes in relatively close proximity to each other - Primrose, Kirby Lake, Christina Lake and Conklin. The South Athabasca Oil Sands air traffic frequency 123.025 MHz is to be used before entering and within the Class E airspace. See the current Canadian Flight Supplement for full details.

Unmanned Aerial Vehicle (UAV) The rapid advancement of unmanned aerial vehicles (UAV) technology has dramatically increased their popularity with both recreational and commercial users in Canada. From 2012 to 2014 Transport Canada has experienced a 485% increase in applications for UAV Special flight operations certificates (SFOC’s). As their popularity increases, so does the risk of an airspace incursion occurring over an Alberta wildfire incident. The Wildfire Management Branch (WMB) has developed the following directives regarding UAV technology:

1) UAV operations will be evaluated and approved on a case by case basis. UAV operations will be approved at a provincial level and must be in compliance with all applicable legislation/regulations.

2) In the event of a UAV airspace incursion over a wildfire incident, the following procedures shall be followed:

• De-conflict the affected airspace by grounding any incident rotor wing and fixed wing aircraft that may be impacted by the incursion. Maintain one assessment rotor wing or fixed wing overhead the affected airspace. This assessment aircraft will perform 3 functions, in order of priority:

1. Act as a lookout to ensure the continued safety of ground operations that may have been affected by the exclusion of aerial suppression efforts. 2. If safe to do so, maintain visual contact of the UAV and assist ground resources in locating the UAV operator. 3. Determine when the airspace is made safe to resume normal operations.

• A ground based search for the UAV operator will be initiated. If contact is made, WMB staff shall notify them that they are illegally operating a UAV in

March 2016 2016 Pilot’s Handbook Page 49 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

restricted airspace, request them to cease their operations immediately and document their name and contact information for submission to the Provincial Forest Fire Centre.

• Ensure all documentation and notification procedures are followed as per the WMB emergency incident response procedures. A UAV airspace incursion is considered an aviation incident. The Provincial Forest Fire Centre will report all UAV airspace incursions to Transport Canada.

Daylight Flying under Visual Flight Rules (VFR) When aircraft are working for Wildfire Management, they will operate under daylight VFR unless the pilot is qualified and current on Instrument Flight Rules (IFR) procedures and the type of aircraft in use. Fish and Wildlife Division may, for the purpose of some of their enforcement operations, fly in a fixed-wing aircraft under night VFR conditions if the pilot is qualified and current on Instrument Flight Rules (IFR).

The air carrier must be approved by Transport Canada to operate the multi-engine aircraft under IFR and night VFR conditions. The following rules and definitions CARs 101.01 will apply:

Day: The period of time beginning one half hour before sunrise and ending one half-hour after sunset and in respect of any place where the sun does not rise or set daily, the period during which the centre of the sun’s disc is less than six degrees below the horizon.

Night: The period beginning one half hour after sunset and ending one half hour before sunrise and, in respect of any place where the sun does not rise or set daily, the period during which the centre of the sun’s disc is more than six degrees below the horizon.

NOTE: Subject to satisfactory visibility and atmospheric conditions set forth in Part VI of the Canadian Aviation Regulations, aircraft flying under VFR on projects for Wildfire Management may fly between the hours one half hour before sunrise and one half hour after sunset. Outside this time, the aircraft must be on the ground.

Sunrise and sunset times for any area in Alberta can be obtained by contacting the nearest Forest Area Dispatcher or NAV Canada Flight Service Station.

In the interest of flight safety (e.g., duty days), Wildfire Management will not use morning and evening twilight calculations for any operations.

Open Door Aerial Work Open door aerial work is any work that is conducted by staff of the Department when the aircraft is no longer in contact with the ground and a door on the aircraft is not secured. Open door aerial work should only be conducted when no other reasonable options exist. Activities included in the open door aerial work include (but are not limited to) animal capture, cargo deployment, infrared scanning, etc. Operations such as Rappel, Aerial Ignition and Hover Exit that have specific operating procedures are exempt from this. If

March 2016 2016 Pilot’s Handbook Page 50 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

open door work needs to be conducted the exposure should be minimized by only having the door open or off when required.

On the Skid or Moving Around Inside the Aircraft If the open door aerial work to be conducted requires the passenger to be free of the lap and shoulder restraints of the helicopter, then the passenger must be provided a fall harness and restraint device. The harness and restraint device are to be provided by the helicopter company. The company must ensure the device is maintained and utilized in accordance to Transport Canada approvals.

Seated and Secured Inside the Aircraft For activities that do not require the passengers to undo their seat belts, but where there is a risk of accidental release of the lap belt, Agriculture and Forestry will provide the approved fall restraint system. This system is a secondary restraint device in the event the quick release seatbelt becomes unfastened. The seatbelt must be worn properly at all times. The device must be attached to aircraft structure as recommended by the aircraft’s aircrew. Visual inspections shall be conducted on the harness the day of the use, prior to being utilized, and recorded on the harness equipment inspection log. If any component of the system fails the inspection, the system cannot be used. The completed inspection log is to be kept with the fall restraint device and all the lanyards during use and when stored.

Airspace Restriction / Notice to Airman (NOTAM)

As per Section 601.15 of Canadian Aviation Regulation Standards:

No person shall operate an aircraft: (a) over a forest fire area, or any area located within five nautical miles of a forest fire area, at an altitude less than 3,000 feet above ground level; or (b) in any air space described in a NOTAM issued pursuant to Section 601.16.

This is an automatic airspace flight restriction for any forest fire. NO advisory to pilots is given; it is expected that all pilots are aware of this requirement.

Personnel must be aware of this restriction as it applies to ALL aircraft not working on the fire at the request of appropriate fire control agency.

Any aircraft found within the restricted area must be reported to Transport Canada for possible investigation and sanctions.

As per section 601.16 of CARS, WM can request further airspace restrictions.

. An advisory NOTAM - an informal NOTAM that is requested via a local NAV Canada office to be given as an advisory to local pilots. No amendment to the normal restricted airspace is given. . A NOTAM - a formal Notice to Airman that may only be issued by Transport Canada. These NOTAM’s may include additional area outside the automatic restricted area and/or additional airspace above the fire.

March 2016 2016 Pilot’s Handbook Page 51 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Transportation of Dangerous Goods All staff must adhere to the current Canadian Transportation of Dangerous Goods Act and Regulations.

If the pilot-in-command does not load or directly supervise the loading of the dangerous goods, the person who loads and secures the dangerous goods will give the pilot-in- command a written list of the following information for each of the dangerous goods: • Shipping name • UN number and class • Gross mass • In the case of explosives, the net explosives quantity

All pilots and/or flight crew accepting dangerous goods aboard their aircraft must have dangerous goods training and carry a valid certification card on their person. Certification for transporting dangerous goods by air is valid for two (2) years.

For casual contract tenders companies must provide letters from TC:

• indicating they have an approved TDG training program • Indicating an approved chapter on TDG in the company’s operations manual.

Considerations for Shipping Propane Tanks One hundred pound bottles of propane or smaller can be shipped by rotor wing or fixed- wing if the above requirements are met.

Considerations for Shipping 365 Liter Propane Tanks The pilot must have a current Transportation of Dangerous Goods Certificate on his person. Before hooking up and moving any propane tanks, full or empty, the following checks must be performed: • Inform the pilot of the dangerous goods to be carried, in writing on proper shipping documentation, • Ensure the pilot has received a copy of the Permit for Equivalent Level of Safety, • Check for correct attachment of the cradle and harness to the tank,

March 2016 2016 Pilot’s Handbook Page 52 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

• Check for defects such as stripped or cracked bolts, frayed or bent wires on the cables, and bent or cracked load ring, and Check for damaged valves and gauges and that the tank has a protective collar or cap.

NOTE: All shipping documents must be kept on record for a minimum of 2 years. All training records must be kept on file for 2 years following the certificate's expiration date.

Pepper Spray Personnel must inform the pilot of the presence of pepper spray in the cargo. Any pilot has the right to refuse to transport pepper spray.

For air transport, pepper spray (aerosol containers) must be placed in separate sealed PVC containers with proper labelling and placed, in order of preference, in:

• an external basket or cage that is not part of the fuselage, • the baggage compartment in the tail boom, or • a baggage compartment with external access only that is within the aircraft fuselage.

Pepper spray is not permitted in the passenger cabin of any aircraft.

Non-Government Personnel on Casual Hire or Contracted Aircraft

Non-government personnel may be a passenger on casual hire or contracted aircraft under the following conditions:

1. Contractors (including potential contractors for contract viewing) or persons doing work in conjunction with the Department (ex: timber personnel viewing fire salvage, land use planning, etc.). o Approval must be obtained from the program Manager authorized to make those decisions. o The person or company must have their own Workers Compensation Board (WCB) coverage (if required by the terms of their contract). o All other regular procedures (manifesting and flight following) shall be followed.

2. School contest winners, ride along programs, volunteers. These individuals unlikely have their own WCB coverage and are not covered by the department WCB account. Aircraft are not to be hired specifically for these situations; such events should be scheduled around routine work activities. The following is to apply: o Be approved by the appropriate Manager, o Require the standard GOA Waiver to be completed prior to the flight, o The flight shall be limited to 15 minutes or less (contest winners), o A Department employee is to accompany the person, preferably in uniform. The employee shall assist the pilot in loading and unloading the passenger(s).

March 2016 2016 Pilot’s Handbook Page 53 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Aquatic Invasive Species (AIS) Prevention

To assist with preventing the spread of aquatic invasive species (AIS) into Alberta from other jurisdictions, any skimmer airtanker or helitanker aircraft imported or returning from export into Alberta will proceed to an airtanker base designated by the Provincial Aircraft Coordinator. Any imported Rotor wing or Alberta Rotor wing returning from out of Province must ensure their buckets are washed as per the AIS Wash-down Procedures prior to being utilised in any Alberta water bodies. The aircraft company is responsible for washing any buckets as per the following procedures:

• Pressure washer must be set to a minimum of 140 Fahrenheit (60oC) • Pressure wash to remove all visible plant parts and mud from all the crevices of the bucket • Spray all parts of the bucket for at least 10 seconds using hot water (140 Fahrenheit or 60oC)

Fur and Game Farm Operations Aviation noise caused by rotor wing and fixed-wing aircraft flying at low altitudes can cause serious economic losses to the farming industry.

Pilots working for Forestry and Emergency Response Division shall avoid over-flying these farms below 2000 feet above ground level (AGL), and where possible, no closer than one (1) mile horizontal. Any aircraft operating under the jurisdiction of Forestry and Emergency Response Division must be made aware of area restrictions and legal land locations of Fur Farms and Game Farms. These locations shall be identified on maps in all Area operations rooms and airtanker bases. Locations shall be provided to incoming casual chartered aircraft as part of the briefing package and to all incoming contract airtanker groups and/or rotor wing. Aviation Occurrence Response and Reporting Agriculture and Forestry uses the Transport Canada Aviation Occurrence definitions as described in the “Aeronautical Information Manual” effective 0901Z, October 15, 2015, to 0901Z, March 31, 2016. The manual can be found at the following link: https://www.tc.gc.ca/media/documents/ca-publications/AIM-2015-2-En-ACCESS-Final.pdf

Aviation Accidents, Incidents, Hazards, Missing Aircraft In the event of an occurrence with a Department hired aircraft, the procedures in the Wildfire Management Branch Emergency Incident Response Procedures WM must be followed.

The Emergency Incident Response Procedures outlines procedures on: • Reporting contacts and timelines that must be followed, • Whether an investigation is required and who conducts it if it is, • Paperwork requirements and timelines that must be followed, and • Process for follow-up after an accident or incident.

March 2016 2016 Pilot’s Handbook Page 54 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Reporting Aviation Near Misses/Hazards, Accidents, Incidents, and cautions All aviation near misses/hazards, accidents, incidents, and cautions are to be submitted on the Aviation Occurrence Report (FP1). All instructions are included in the form online and can be filled out either electronically or by hand. The FP1 should be completed within 24hrs of the occurrence and submitted to the Forest Area DO.

This is not meant to be a punitive process for reporting near misses/hazards, accidents, incidents and cautions but if someone is found at fault the appropriate actions, mitigations, and potentially punitive actions will be carried out.

Procedures for Aviation Accidents / Missing Aircraft / Incidents Where an aircraft is involved in an accident, no person shall displace, move or interfere with the aircraft or its contents without first obtaining permission from the Transportation Safety Board of Canada.

The exception to this rule is the need to move/displace the aircraft or its contents to extricate a person, to prevent destruction by fire or other cause, or to avoid endangering other persons or property. Subject to the above, no person shall interfere with or otherwise disturb an aircraft accident site. Where an aircraft must be displaced or moved, the person supervising the move will photograph, draw a diagram(s) and make notes on the condition of the aircraft and its contents, and on the accident site before anything is disturbed, providing the situation is not life-threatening.

In accordance with the Transportation Safety Board Regulations, the pilot-in-command, operator, owner and, in the case of a near-miss, any Air Traffic Controller with knowledge of the incident shall report it to the appropriate office(s) (as outlined above), giving the date and place of the incident and other details as set forth in Schedule “B”, and an FP1 shall be completed.

Safety is mandatory in air operations and is the first priority in planning and conducting all air operations. Where any Department Staff member observes unsafe actions or is in doubt as to pilot/aircraft proficiency, or if staff are aware of possible problems with the pilot’s health, the flight shall be cancelled and the Forest Area and PFFC Duty Officers advised immediately.

The Provincial Forest Fire Centre contracts an Aviation Safety Consultant to check aircraft operations as required. Where necessary, this same individual will conduct field investigations into aircraft accidents, incidents or hazards, excluding the aircraft or flight crew investigations, which are the responsibility of the Transportation Safety Board. A report on Wildfire Management procedures before and leading up to the accident or incident will be compiled.

Accidents and Missing Aircraft When any aircraft operating under the jurisdiction of the Department is involved in an accident the Forestry Program Manager, Forest Area Manager, Wildfire and Air Operations Officer, Wildfire Technologist, Forest Area Duty Officer or, in their absence, any officer must report immediately to:

March 2016 2016 Pilot’s Handbook Page 55 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

• Forest Area, and to the Provincial Forest Fire Centre Duty Officer, • The local RCMP, • The local Forest Area Office. • Regional Occupational Health and Safety if fatality has occurred and • The aircraft company if the aircraft was chartered locally.

An FP1 must be completed.

NOTE: In the case of an accident, a verbal report must be passed on to both the Forest Area and the Provincial Forest Fire Centre Duty Officer within 15 minutes of the occurrence and followed up with a hardcopy within one (1) hour. A written status report must be forwarded to the Forest Area and Provincial Forest Fire Centre Duty Officer within two (2) hours of the event. The status report is to include what has been done and what is still to be done to complete the formal report(s). The Provincial Forest Fire Centre will contact the following: • Transportation Safety Board (if known accident or if aircraft is missing), • Department of National Defence Search and Rescue Program (if aircraft is missing), • Wildfire Service Director/ Director of Wildfire Operations • Director of Communications, • Human Resources Branch if an injury has occurred, • Air Safety Officer, and • Aircraft Accident Team (if required).

The Provincial Forest Fire Centre will also co-ordinate flight/transportation for all investigation personnel, as required.

The Wildfire Operations Director or Executive Director of Wildfire Management (or his designate) will contact the Assistant Deputy Minister. If the Assistant Deputy Minister or his designate cannot be located, the Director will ensure that the Deputy Minister is contacted.

Regional Occupational Health and Safety will contact the Provincial Occupational Health and Safety, who in turn will contact the Department of Labour Occupational Health and Safety, if applicable. The Forest Area Office will contact the Regional Director if an injury has occurred. In all cases, it is the responsibility of the Forest Area Manager to establish the “one (1) window” media contact with the Director of Communications. The involved Division will commence the notification process from the accident scene to the Forest Area Manager.

Missing Aircraft Where an aircraft operating under the jurisdiction of the Department is missing on a flight, the designated staff member responsible for closing the flight itinerary, Forest Area Duty Officer must ensure the following people are notified immediately:

• Forest Area Manager • Wildfire Operations Officer • Provincial Forest Fire Centre Duty Officer

March 2016 2016 Pilot’s Handbook Page 56 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

NOTE: When an aircraft is reported missing, it is considered to have been involved in a reportable accident.

An aircraft flying under the jurisdiction of the Department shall be considered missing when: • The calculated flying time from the last reported position to the next reporting point is greater than 30 minutes; or • The estimated time of arrival is greater than 30 minutes; or • On project work where there has been no communication from the aircraft for greater than 30 minutes; or • On local project work where the pilot has indicated an extended period of silence due to poor communications transmission (e.g., on the ground, waiting for personnel), and the indicated period is greater than 30 minutes.

As soon as it becomes obvious an aircraft is missing, attempts should be made to communicate with it on all frequencies in current use within the Forest Area of operation and, all contacts and attempts shall be recorded fully in the dispatch log, and the Duty Officer should be notified immediately. In the event an aircraft is determined to be missing, the office providing the flight radio monitoring shall ensure the following are notified:

• Forest Area and Provincial Forest Fire Centre Duty Officers, • An air traffic control crew, a flight service station, community aerodrome radio station or, • A rescue co-ordination centre, • Aircraft Company owning the missing aircraft.

Along with above, and providing sufficient daylight remains, an aircraft, complete with flight crew and observers, should be readied for immediate departure upon approval to conduct a “track crawl” and radio search pending arrival of a Search and Rescue Aircraft. Telephone numbers of specified contact people for missing aircraft incidents will be updated quarterly by Provincial Forest Fire Centre Air Operations and distributed to all persons who could potentially be involved on a provincial basis.

Incident Where a situation involves any aircraft operating under the jurisdiction of the Department in an incident, the Forestry Program Manager, Wildfire Operations Officer, Wildfire Technologist, Duty Officer or, in their absence, any officer must report immediately to: • Forest Area and the Provincial Forest Fire Centre Duty Officer.

The Provincial Forest Fire Centre will contact the following: • Transportation Safety Board, if required, and • Air Safety Officer.

NOTE: The Transportation Safety Board defines a reportable incident as an incident resulting directly from the operation of an aircraft having a maximum certificated takeoff weight greater than 2250 kg, or from an aircraft being operated under an air operator certificate issued under Part VII of the Canadian Aviation Regulations.

March 2016 2016 Pilot’s Handbook Page 57 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

An FP1 must be completed. NOTE: In the case of an incident, a verbal message must be passed on to both the Forest Area and to the Provincial Forest Fire Centre Duty Officer within 60 minutes of the occurrence and followed up with a hardcopy within two (2) hours. A written status report must be forwarded to the Forest Area, Provincial Forest Fire Centre Duty Officer within four- (4) hours of the event. The status report is to include what has been done and what is still to be done to complete the formal report(s).

Near Miss/Hazard Reporting A completed Aviation Occurrence Report (FP1) shall be turned in to the supervisor, the Incident Commander or Forest Area Duty Officer. The Forest Area office will fax a copy of the report to the Provincial Forest Fire Centre - Air Operations. Individuals may file a hazard report anonymously, but if they provide their name, they will get a response back answering their concern(s).This report is not a quick fix for all problems, nor is it a replacement for reporting accidents. It is a tool to start communication and a way to be heard.

March 2016 2016 Pilot’s Handbook Page 58 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

APPENDICES

Alphanumeric Wildfire Incident Maps Wildfire maps produced by the Wildfire Management Branch use a simple alphanumeric grid numbering system for both feature reference and helipad numbering and provide GPS coordinates. The alphanumeric grid is a coordinate system that uses letters on the horizontal axis ascending from West to East and numbers on the vertical axis ascending from North to South. The alphanumeric grid system allows for quick reference because the feature or helipad name references the location, which in an emergency becomes very important.

Features are given a name and have a corresponding grid reference (combination of letter and number) and GPS coordinates. Helipads are named by their grid reference and assigned a dash number. The dash number is used to differentiate between two or more helipads in the same grid. The dash numbers assigned are based on the order in which the helipads were created. Example map below: 2 helipads were created in grid H3. The first helipad was assigned the pad number H3-1 while the second was assigned pad name H3-2.

March 2016 2016 Pilot’s Handbook Page 59 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Example of Air Operations Map Using the Alphanumeric Grid System

March 2016 2016 Pilot’s Handbook Page 60 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Alberta Third System of Survey Maps produced and used by Wildfire Management emphasise the Township Grid System as the major reference system. Compared with the Latitude-Longitude System, which denotes a point at the intersection of two lines, the Township Grid System denotes an area of known size located in a certain position.

Subdivision The smallest regular unit of land in Alberta is a Legal Subdivision (abbreviated LS or LSD). This unit is square, being one-quarter mile (0.4 km) in length and width, containing 40 ac. (16.2 ha, 1 acre = 43,560 sq. ft. or 4,047 m2).

Section Sixteen Legal Subdivisions make up 1 Section (abbreviated SEC), the key unit of the Township Grid System. It is a square measuring 1-mile at each side and containing approximately 640 ac. (259 ha).

Quarter Section Four Legal Subdivisions form 1 quarter Section. These are identified as NE¼, NW¼, SE¼, and SW¼.

March 2016 2016 Pilot’s Handbook Page 61 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Township A Township is a square with 6 mi. sides, and contains 36 sections (abbreviated Twp.). The numbering starts in the SE corner of the Township. The area of a Township is that of 36 sq. mi. (57.9 km2) plus the width and length of the road allowances.

A Township strip runs in an east-west direction. Starting at the United States border, parallel strips 6 miles wide are numbered consecutively from the south to the north. Strip #1 borders the United States, while strip #126 borders the . Each strip constitutes a series of Township squares.

Road Allowance A standard Government Road Allowance, 66 ft. (20 m) in width, is left between Sections. Section boundaries that are not Road Allowances are called “Blind Lines”.

Road Allowances are provided after each mile in an east-west direction; i.e., five north- south road allowances within the Township in a north-south direction, with three Blind Lines forming the remaining Section boundaries.

Township Range Each Township is identified by two numbers, which indicate its position geographically. These are Township number and Range number.

The Range (abbreviated Rge.) numbering starts immediately west of a Meridian, and increases in 6 miles Blocks (one township) as it goes west. Thus, the Township marked with an * in the diagram below is numbered Township 3, Range 2 West of the Fourth Meridian or in short form, Twp. 3, Rge. 2, W4M.

March 2016 2016 Pilot’s Handbook Page 62 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Meridian The line from the North Pole to the South Pole by the shortest route is called a Meridian. These lines are used as basic starting points for distances measured east and west. In Canada, these meridians have been arbitrarily numbered from 1 to 6. The first (“principle”) Meridian is located just west of ; the second is on the - border; the third is in Saskatchewan; the fourth on the Alberta-Saskatchewan border; the fifth runs through Stony Plain, Alberta, and the sixth through a point just east of the town site of Jasper.

Ranges are always referred to as being west of one of these Meridians and the Range numbering resumes with “1" west of each Meridian.

Correction Lines Townships are always slightly tapered towards the north because the earth is round. Around Edmonton, this tapering means that the south of the Township is about 65 ft. wider than the northern boundary. Sections at the northern boundary of a Township are about 10 ft. narrower than those at the southern boundary of the same Township. To prevent this convergence from becoming too great, a break is made every four Townships. This break is called a Correction Line and is not, as may be supposed, the result of the surveyor’s error. Note that the jog at the Correction Line becomes greater the further west you move from the Meridian. Just east of the next Meridian to the west, this jog is greater than 1 mi.

March 2016 2016 Pilot’s Handbook Page 63 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Fractional Townships and Fractional Sections At the Meridian, all Townships are cut off to the straight, geographic north-south line and a fresh start is made. This results in fractional Townships and fractional Sections.

Finding a Location Based on a Legal Description When a legal description is received over the radio, the reverse procedure for transmitting is followed to find it on the map:

1. Find the Meridian. 2. Find the Township at the intersection of the Range column and the Township strip. 3. Find the Section with the Township template. 4. Find the quarter Section or Legal Subdivision.

For example, suppose you are told to proceed to LSD 8 of Section 10, Twp. 24, Rge. 8 W5M. First, you would locate the fifth Meridian. The location you want will be west of this Meridian. Next locate the Range by using the Range numbers that are usually located horizontally along the top and bottom of the map. Then locate the Township (Township numbers are usually located vertically along the sides of the map). Finally, locate the Section number, then the Legal Subdivision.

Fire Line Equipment Weights Lbs. Kgs. Axe, single bit, standard fireline 5.0 2.3

, Backpack, water, (empty) c/w handspray Bag 7.0 3.2 pump Batteries (144 per box) 8.33 3.8 Batteries (576 per box) 34.0 15.4

Bladder Water, slingable, 60 gallon 10.0 4.5 Water, slingable, 110 gallon 12.0 5.5 Water, slingable, 300 gallon 35.0 15.9

Bottle Propane, 20 pound, full 45.0 20.5

March 2016 2016 Pilot’s Handbook Page 64 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Propane, 40 pound, full 90.0 40.9 Propane, 100 pound, full 180.0 81.8 Propane, camp stove model empty-full wts. 1.05 – 2.0 0.48 - 0.91

Coveralls Nomex, Yellow 2.55

Can Gas, plastic, 5 gallon, full 46.0 20.9 Gas, plastic, 5 gallon, empty 2.0 0.9 Gas/Oil, plastic, Combination, 21/2 gallon full 23.4 10.6 Gas/Oil, plastic, Combination, 21/2 gallon empty 2.7 1.2

Three different bars sizes 16",18" and Chainsaws 20"(slight weight variation) 16” 18.0 8.2 18” 18.25 8.28 20” 18.36 8.33 Chainsaw Oil 4 liter jug 8.0 3.6 Chainsaw pack 3.0 1.4

Drink Bottles Gatorade / PowerAde- 710ml bottle 1.5 0.68 12 pack 18.0 8.2 24 pack 36.0 16.3

Water 1 Liter bottle 2.26 1.1 Case of 12 27.2 12.3 500 ml Bottle 1.2 0.54 12 pack 14.4 6.5 24 pack 28.8 13.1 5 gallon bottle / full 50.0 22.7

Fire Foam Concentrate Pail, 5 gallon, full 46.0 20.9 Drum, 45 gallon, full 480.0 218.2

Fuel and Barrel Jet A 423.0 192.3 Jet B 410.0 186.4 AV GAS 381.0 173.2 Diesel 558.0 254.0 Unleaded 384.0 175.0 Full Propane Pig 850.0 386.4 Empty Drum Empty Propane Pig 50.0 23.0 275.0 125.0

March 2016 2016 Pilot’s Handbook Page 65 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Fusee’s single fuse 0.52 0.23 Case of 72 42.0 19.1

HAT, safety hard 1.0 0.5

Heater Airtight, 18 inch c/w 6 section stove pipe 26.5 12.1 Airtight, 24 inch c/w 6 section stove pipe 26.5 12.1 NOTE: use same weight for both stove sizes

Aerial Ignition Helitorch, LFS made c/w kit 170.0 77.3 Aerial Ignition Device (Ping Pong Machine) c/w kit 95.0 43.2

Hose Fire, 5/8" (dry) per 50 feet 1.2 0.5 Fire, 1" (dry) per 100 feet 9.0 4.1 Fire, 1 1/2" (dry) per 100 feet * 13.5 to 16.25 6.1 to 7.4 Suction, 1 1/2" Draftex 4.0 1.8 Suction, 2", Draftex 5.0 2.3 Suction, 2", Rubber 15.0 6.8 Bagged Hose 4/bag c/w hose bag and carton 61.0 27.7

* Hose Dry/Wet 13.5 to 16.25 Lbs. variation due to the type of lining inside the hose. Note: Add approx. 2 lbs. / roll to be added for wet hose

Kit First Aid, Personal, ‘P’ 0.4 0.18 First Aid, Type 2 2.33 1.1 First Aid, Type 3 4.25 1.9 Camp Maintenance 10.0 4.5 Chainsaw w/o saw 25.0 11.4 Crash, Rescue 24.0 Comms, unit c/w 4 radios 14.0 6.4 Dozer Boss 25.0 11.3 Pump, BB4, w/o pump 37.0 16.8 Pump, Floto, w/o pump 28.0 12.7 Pump, Mark III, w/o pump 54.0 24.5 Pump, Mini-Mark/Shindawa, w/o pump 29.0 13.2 Sprinkler System 80.0 36.3 Sprinkler Mini 35.0 15.9 Water truck 6.5 2.9

Machete 1.9 0.9

MRE's – Box 36.0 16.3

March 2016 2016 Pilot’s Handbook Page 66 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

PAIL, canvas water 1.0 0.5

Polythene Plastic Clear, 4 mil, 100 foot roll 22.0 10.0

Power Plant 300 watt 50.0 22.7 500 watt 57.0 25.9 1 KW 215.0 97.7 3.5 KW 200.0 90.9

Pulaski 5.5 2.5

Pump And Engine BB4 180.0 81.8 Floto 42.0 19.1 Mark III 64.0 29.1 Mini-Mark/Shindawa 10.0 4.5 Pump, Mini-Striker 21.0 9.5

Pump, fuel, barrel, hand, rotary 18.0 8.2

Radio, TK270 with batteries 1.12 0.51

Rake, firefighting 4.0 1.8

, Brushcutter Saw 27.0 12.2

Shovel, bantam firefighting, long handle 4.5 2.0 Shower Portable, single 110.0 50.0 Portable, double c/w tent and wood boxes 455.0 206.8

Stove, cook, 4 burner propane w/o bottle 75.0 34.1

TANK, c/w pad where required Water, self-supporting, 500 gallon 32.0 14.5 Water, self-supporting, 1,000 gallon 48.0 21.8 Water, self-supporting, 1,500 gallon 77.0 35.0 Water, self-supporting, 2,500 gallon 125.0 56.8 Water, self-supporting, 4,000 gallon 110.0 50.0 Water, self-supporting, 5,000 gallon 160.0 72.7 Water, self-supporting, 12,000 gallon 200.0 90.9

Tent Canvas, 12' x 14' 70.0 31.8 Modular, army c/w boxes 770.0 350.0

March 2016 2016 Pilot’s Handbook Page 67 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Pumpkin, 18' - c/w green boxes 745.0 338.6 - c/ red boxes 545.0 247.7 Nylon, Overhead 10.72 4.9 Nylon, Firefighter 7.0 3.2 Ranger, 18' x 30' 404.0 183.6

Torch, Torch, drip, brush burning 5.0 2.3 Panama Torch, full 35.0 15.9 Panama Torch, empty 11.2 5.1 Fedco torch, full 56.0 25.4 Fedco torch, empty 15.4 7.0

NOTE: All equipment was weighed on a certified scale

Helicopter Landing Areas

In remote areas, helibases and helispots are necessary for the transport of personnel, equipment and supplies to the fireline.

Helibase The helibase is the main location for parking, fuelling, maintenance and loading of helicopters in support of an incident. When possible, Agriculture and Forestry utilizes existing airstrips, open fields or meadows with road access.

Helispot A helispot is any designated location or area where a helicopter can safely take-off and land. Helispots may be used for offloading supplies, equipment or personnel. Site section and preparation is a critical aspect of safe and efficient helicopter operations.

Helipad A helipad is the surface or structure where the helicopter actually lands

Helispot Size and condition:

• The diameter of the helispot clearing should be a minimum of twice the rotor diameter • Light or intermediate helicopters (23 – 25 metres) • Medium helicopters (28 – 32 metres) • Any dangerous trees and hazards shall be removed • Helispot shall be free from debris, obstacles and garbage; any equipment and loose gear will be secured • Skid logs may be used in soft ground

March 2016 2016 Pilot’s Handbook Page 68 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

conditions • Wind indicators should be installed

Agriculture and Forestry will strive to construct safe and solid landing areas. Ultimately it is up to the pilot to accept, reject, or suggest improvements to be made to any landing area.

Glossary of Wildfire Terms

Abort A planned release of retardant in order to achieve an aircraft’s gross landing weight.

After Action Review Is a debriefing following a mission / incident, the AAR may be informal or formal but should involve everyone connected to the event. The AAR should focus on continual improvement, not on assigning blame.

Air Attack Officer (AAO) Each airtanker group has an assigned “birddog” aircraft that carries an air attack officer (AAO) and a birddog pilot. The AAO coordinates air attack operations on wildfires and ensures aerial operations are conducted in an effective, efficient and safe manner. To ensure the safety of all aircraft in the vicinity, the birddog team also manages the airspace over the fire.

Air Tactical Group Supervisor When two (2) Birddog aircraft are on a fire, one Birddog may assume the Air Tactical Group Supervisor (ATGS) role. Once ATGS is established, that Birddog team will be responsible for managing the airspace for the fire. The ATGS will maintain a high altitude orbit while the tactical birddog will remain 1000 ft. AGL and continue to work with the airtankers auctioning the fire. The ATGS will be identified as “Air Attack” and either the Wildfire number or a geographical identifier. For example: Air Attack Fire 31 or Round Hill Air Attack. Once ATGS has been established it will be announced on the Air Advisory and Forest Area Firenet Frequencies.

Automatic Fire Restriction As per the Canadian Air Regulation Standards no person may operate an aircraft over a forest fire area, or area that is located five (5) nautical miles around the fire perimeter and at an altitude of less than 3000 feet above ground level (AGL). If additional space is required, due to increased aircraft activity, a request must be made through the Forest Area Office to have a Notice to all Airmen (NOTAM) issued by transport Canada for the fire area.

Called Shot A drop technique whereby the birddog triggers the Airtanker drop by voice command, saying “3, 2, 1, now”.

Canadian Air Regulations Standards (CARS) Transport Canada regulations and standards for civil and commercial aviation

March 2016 2016 Pilot’s Handbook Page 69 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Cold Lake Air Weapons Range The Cold Lake Air Weapons Range is a Department of National Defence (DND) control area for the purpose of allowing military aircraft a practice / training area in the boreal forest. All aircraft are restricted from entering the zone without permission from the Cold Lake Forces Base. All aircraft must request permission to enter the range by contacting the Lac La Biche Duty Officer. If access is allowed, both a corridor and maximum elevation will be assigned. A map of the CLWR is provided in the map books and a digital map is available through PFFC. Upon clearance by the duty officer, the pilot will contact the tower at Cold Lake.

Coverage Levels A number representing the number of gallons of retardant mixture dropped, or prescribed, to cover fuels in a 100 sq. ft. area.

Day Base A temporary moving of a tanker group or rotor wing to another base due to fire hazard coverage levels or to support on-going fire operations. The aircraft is expected to be operational while enroute to the base.

Drop Assessment The air attack officer or Helicopter Coordinator will access each drop from an Airtanker or helitanker for its accuracy and effectiveness. Drops will be rated as a bull’s eye, short, long, left or right. Short and long drops are rated as a fraction of the entire load. i.e. ¼ load short. Left and right drops are assessed using the wingspan of the aircraft as a reference i.e. the load was ½ wingspans left. Other factors that can be assessed include drop height, speed, coverage, foam and drift.

Dummy Run A simulated bombing run made on a target by the Birddog or Helicopter Coordinator to indicate both the target and run to the Airtanker.

Duty Day A pilot’s duty day is restricted by the Canadian Air Regulations. This duty period is (14) fourteen hours in any 24 consecutive hours.

A pilot’s duty day starts when a pilot: Reports for a flight, Reports for standby that has a reporting time of one hour or less, Performs any duty required by the company, or Performs any duty designated by the Minister of Transport.

A pilot’s duty day ends when: The engine is turned off at the end of the final flight, or At the end of a predetermined standby period, whichever is later.

March 2016 2016 Pilot’s Handbook Page 70 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Fire Bombing Circuit

Fire Foam (Phos-Chek WD881C and Fire-Trol 104) Are wildland Class A firefighting liquid concentrates, consisting of a surfactant, corrosion inhibitor and stabilizers.

Firenet A radio system that is a province wide VHF-FM repeater network designed to meet the unique needs of Wildfire Management’s, prevention, detection and suppression operations. It will also be used on a limited basis by other Divisions within Agriculture and Forestry and Environment and Parks.

Flight Report A0-02 To ensure accurate information is collected at the time of the flight, all activity has to be recorded daily for each aircraft in use or under contract. The Daily Flight Report (AO-02) has been created and used for this purpose. An AO-02 Daily Flight report will be filled out for each aircraft under contract whether or not any flight has taken place during the day. When flight hours occur, a report will be completed and will contain information about: purpose of the flight, take-off and landing by location, hours flown, appropriate coding, Fuel consumption, and Crew expenses.

Forward Looking Infrared (FLIR) Wildfire Management, Air Tanker Program, owns and contracts a variety of Thermal Imagers commonly known as the FLIR (Forward Looking Infrared) scanner.

Half On / Half Off An Airtanker or Helitanker drop made parallel to a given reference (fires edge) where one side of the load falls on the burning fuel and the other half falls on the adjacent unburned fuel.

Incident Commander Is the individual responsible to organize, assign, and supervise fire suppression activities on any given incident. When assigned to an initial attack fire, the aircraft report to the Incident Commander.

March 2016 2016 Pilot’s Handbook Page 71 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Initial Fire Assessment Form (FP41) The first resource on scene is responsible to complete and pass the initial fire assessment. Information on wildfire status, size, spread rate, fire type, fuel type, values at risk and requirements are recorded and relayed to the Forest Area Fire Centre.

Lead-in A technique whereby the Airtanker follows the Birddog on a final run.

Lone Wolfing Lone wolfing refers to a tanker conducting drops not under the immediate supervision of a Birddog. Lone wolfing of Airtankers is prohibited. All firebombing must be done under the direct supervision of a Birddog. The only exception is an Airtanker dropping a load over an approved abort zone and in this case the Airtanker must maintain 500 feet above ground level.

Long Term Retardant Phos-Chek® LC95a - A liquid fertilizer grade ammonium polyphosphate (11-37-0), combined with guar gum, color package and a corrosion inhibitor. The mixing ratio of water to LC95a liquid concentrate is Alberta is 5.5:1This is the current retardant in use for the Province of Alberta, and is supplied by ICL Performance Products Limited.

Mandatory Rest Period A Minimum Rest Period is a period of time in which the pilot is free from all duty, is not interrupted by the company, and is provided an opportunity to obtain not less than eight hours of prone rest, time for meals and personal hygiene, and time to travel to and from the rest facility. Time spent completing any duties required by the company following flight duty time is not to be considered part of the minimum rest period.

Operational Birddog Working or low level birddog, sometimes referred to as the Tactical Birddog. Operational birddog CONTROLS the base of the stack which initiates movement in the stack

Parallel Right/Left Same bearing but position aircraft a specified distance right or left of previous drop. This can be a tag on but parallel right or left.

Provincial Aircraft Coordinator (PAC) An individual based in the operations room at PFFC, and is responsible for the coordination of safe efficient use of Provincial Aviation assets.

Quick Strike From time to time Airtanker groups may be dispatched into neighbouring jurisdictions to assist in wildfire suppression.

Reportable Near Miss Transportation Safety Board defines a reportable incident as an incident resulting directly from the operation of an airplane or a rotorcraft. A verbal message must be passed to both the Forest Area and to the PFFC Duty Officer within 60 minutes of the occurrence and

March 2016 2016 Pilot’s Handbook Page 72 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

followed up by a hardcopy within two (2) hours. A written status report must be forwarded to the PFFC Duty Officer within four (4) hours of the event.

Roll-ups A retardant drop placed in front of a visible reference point, such as another retardant load, a structure, a water body, etc. The intent is have the load end as it reaches the given reference point. Care must be made as to load type and delivery.

Salvo Place entire load on designated target. Salvo is a common term for tankers with a fixed door system such as a CL-215. A 4 door salvo with mean a four door drop all at once.

Tag On and Extend To drop retardant in such a way that the load slightly overlaps and then lengthens a previous drop. A 25% overlap for conventional drops or 30 to 40 feet (for constant flow tanks) is desired.

Side Stepping When bomb runs cannot be made by running down a slope using short drops dropped 90 degrees to the slope can build a line. Care should be taken as slope can introduce a different ground elevation off each wing of the aircraft. I.e. a pilot in an L-188 who drops across the slope (pilot on downhill side) may not be aware of rising terrain under the uphill wing.

Silent Stack Upon visually observing the Airtanker immediately below them descend to a lower position in the stack, the pilot may commence his descent to next lower stack position. This will continue until all Airtankers in the stack have taken up their new stack position. Visual reference to the Airtanker immediately below your present position must be maintained.

Stack An established holding pattern over a fire for Airtankers, awaiting drop instructions. Spacing will be at 500 ft. intervals. The operational birddog controls the stack movements. If the ATGS role has been activated they will assign an entry altitude for incoming tankers.

Target Elevation Is the intended elevation, feet above sea level, at which an Airtanker is to release their load. Target elevation is equal to the ground elevation of the target, in feet above sea level, plus the intended drop height above ground. This elevation is provided to the Airtanker, by the Birddog as part of their run description.

TCAS / TCAD The Traffic alert and Collision Avoidance System (or TCAS) or Traffic Collision Avoidance Device (or TCAD) is an aircraft collision avoidance system designed to reduce the incidence of mid-air collisions between aircraft. It monitors the airspace around an aircraft for other aircraft equipped with a corresponding active transponder, independent of air traffic control, and warns pilots of the presence of other transponder-equipped aircraft which may present a threat of mid-air collision (MAC).

March 2016 2016 Pilot’s Handbook Page 73 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Thirty Minute Check-in Mandatory position and status updates will made from an aircraft to the Forest Area’s dispatch centre every 30 minutes.

Unserviceable Aircraft Report Unserviceable is defined as when the aircraft, pilot or engineer are not in condition to perform, fails to perform or is unavailable to perform during the alert/standby period as defined in “Flight Crew Statuses” or work assignment period specified in the daily Incidence Action Plan or Forest Area daily operations plan.

VHF-AM Air Advisory Wildfire Management has been assigned a number of VHF-AM frequencies from Industry Canada. The allocation of these frequencies is managed by the communication section of Forest Operations. The air attack program has been given exclusive use of a number of these which have been assigned to the 8 air tanker groups. Five (5) frequencies have been allocated to be used for air to air advisory. The following are the radio frequencies to be used for Initial Attack air advisory:

• 129.800 MHZ (Primary) • 128.950 MHZ (Secondary) • 131.850 MHZ (Alternate) • 130.750 MHZ (Alternate), North of 52° only • 130.175 MHZ (Alternate), North of 53°only

Visual Flight Rules (VFR) Are a set of aviation regulations with which a pilot may operate an aircraft, in a specific airspace, with meteorological conditions better than Basic VFR Weather Minimums. For example, weather conditions sufficient to allow the pilot, by visual reference to the environment outside the cockpit, to control the aircraft's attitude, navigate, and maintain safe separation from obstacles such as terrain, buildings, and other aircraft.

Wail Siren Siren signalling the ground crews, that Airtanker Operations in the area have been completed.

Yelp Siren Siren signalling the ground crews of an intended and/or imminent drop from an Airtanker. All ground crews must immediately move clear of the drop zone.

March 2016 2016 Pilot’s Handbook Page 74 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Airspace Chart 1

March 2016 2016 Pilot’s Handbook Page 75 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Airspace Chart 2

March 2016 2016 Pilot’s Handbook Page 76 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Airspace Chart 3

March 2016 2016 Pilot’s Handbook Page 77 of 78 © 2016 Government of Alberta

Agriculture and Forestry / 2016 Pilot’s Handbook

Airspace Chart 4

March 2016 2016 Pilot’s Handbook Page 78 of 78 © 2016 Government of Alberta