System Configuration Guide
Total Page:16
File Type:pdf, Size:1020Kb
Express5800 Servers Express5800/E110b-M System Configuration Guide 4th Edition, April 2011 Contents: Introduction Server chassis Specification 1. Consolidated PSU External view 2. Server chassis Outline drawing / Images 3. Cooling fan box Tested operating system list 4. Blank Panel Configuration diagram 5. Cable Management kit System configuration steps overview 6. DC power cable Quick configuration diagram Consolidated PSU System Configuration 1. Consolidated PSU E110b-M servers 2. Power supply module 1. Basic system 3. Unit Management 2. Processor Supplementary Notes 3. Memory 4. Internal drive 5. Keyboard 6. Mouse 7. Optical disk drive 8. Floppy disk drive 9. System management System Configuration Guide Express5800/E110b-M Introduction The document contains product and configuration information that enable you to configure your system. The proper configuration of your system will be configured by following the step to select the components. The section to select the components mostly consists of two part, configuration information, selectable peripherals list. Then please select configuration firstly and select necessary peripherals. Sample of section to select component: 4. Internal drive(HDD / SSD) [std. 0 / max. 1] Configuration information (non hot plug) Integrated SATA controller Standard Internal SAS/SATA cable SATA HDD 3Gb/s SATA [K410-XXXXXX] SATA SSD NOTE SAS hard drive is not supported in the system. Supported SATA HDD, SATA SSD Selectable peripherals list SATA HDD (2.5-inch, 3Gb/s) XXX GB HDD 7,200rpm [NXXXX-XXX] YYY GB HDD 7,200rpm [NXXXX-XXX] SATA SSD (2.5-inch, 3Gb/s) XX GB SSD [NXXXX-XXX] About icons: • The icons on the configuration chart stand for the supporting OS as showing in the following table. • For the request to use Linux OS, please also refer to the website http://www.nec.com/global/prod/express/linux/index.html … Supported by NEC … Certified by Distributor 2003 : Windows Server 2003 (with SP1 or later) EL4 : Red Hat Enterprise Linux ES4/AS4 : Red Hat Enterprise Linux 2003x64 : Windows Server 2003, x64 Edition EL4x64 ES4(EM64T)/AS4(EM64T) 2003R2 : Windows Server 2003 R2 EL5 : Red Hat Enterprise Linux 5/AP5 2003 R2x64 : Windows Server 2003 R2, x64 Edition EL5x64 : Red Hat Enterprise Linux 5(EM64T)/AP5(EM64T) 2008 : Windows Server 2008 ML4 : MIRACLE LINUX V4.0 2008x64 : Windows Server 2008 (x64) ML4x64 : MIRACLE LINUX V4.0(EM64T) 2008 R2 : Windows Server 2008 R2 (x64) AXS3 : Asianux Server 3 ESXi4 : VMware ESXi 4 AXS3x64 : Asianux Server 3(EM64T) SL10 : SUSE Linux Enterprise Server 10 SL10x64 : SUSE Linux Enterprise Server 10(EM64T) NEC Corporation 4th Edition, April 2011 2 System Configuration Guide Express5800/E110b-M Specification (Express5800/E110b-M) Outline The low-power 1-socket server optimized for high density mounting Features Achieves low power consumption with Intel® Atom™ Processor N450. Supports one 2.5-inch SATA and SDD Equips EXPRESSSCOPE Engine 2 to enable superior system management Model Express5800/E110b-M Product Code N8100-1635F Type Intel® Atom™ Processor N450 Clock Speed 1.66GHz Processor Number of processors (std./max.) 1/1 L2 Cache (per core) 512KB Core and Thread (per processor) 1C/2T I/O Controller Hub (IOH) Intel® 82801HBM chipset Capacity (std./max.) 0 GB/2GB (2x 1GB) Supported Memory DDR2-667 SO-DIMM Native Speed (max.) 667MHz Memory Error detection and correction - Memory sparing - Memory mirroing - Capacity (std.) - Hard 2.5-inchHDD: SATA 1TB (1x 1TB) Capacity (max.) drive 2.5-inchSSD: SATA 100GB (1x 100GB) Hot swap Not supported Storage Controller type and supported RAID level SATA 3Gb/s: No RAID feature Optical disk drive External drive (Optional)*1 Floppy disk drive Optional: Flash FDD (1.44MB)*2 Media bay - Expansion Type - Controller/Video RAM Integrated in Server Management Controller/32MB Graphics Color depth and Resolution 16.7M color: 640x480, 800x600, 1, 024x768, 1, 280x1, 024 Interface 1x SUV (1x Seial B, 2x USB 2.0, 1x VGA) Dimensions (W x D x H) 22.1 x 453.5 x 119.4 mm Weight(min./max.) *3 0.7kg/1.0kg Power consumption (DC12V, Max. config, Idle) 23.3 W Power consumption (DC12V, Max. config, Operating) 27.0 W Power consumption (AC power supply, Operating) 2091VA/2063W (System, max) Temperature, Relative Humidity Operating: 10 to 40°C/Non-Operating: -10 to 55°C, 20 to 80%(non condensation) Included Accessories Getting started Supported - operating Red Hat Enterprise Linux 4.8 or later, Red Hat Enterprise Linux 4.8 (EM64T) or later Certified by ISV *4 system Red Hat Enterprise Linux 5.4 or later, Red Hat Enterprise Linux 5.4 (EM64T) or later Tested operating system *4 Refer to "Linux on NEC Express5800" on NEC global site Note: *1 Arrange an External DVD for maintenance and OS installation purpose. *2 Arrange Flash FDD if needed. For intended uses, refer to the Flash FDD Supplementary Notes in this guide. *3 Minimum configuration: 1x 1GB DIMM and no HDD or SSD, Maximum configuration: 2x 2GB DIMM, 1x 500GB HDD *4 Refer to Linux on NEC Express5800 on NEC global site for the latest information. NEC Corporation 4th Edition, April 2011 3 System Configuration Guide Express5800/E110b-M Specification (Server chassis) Outline The server chassis employing up to 20 E110b-M server Features Up to 20 E110b-M servers can be installed in 3U height. Supports hot plug replacement for servers Supports hot plug-able redundant fan to enable to replace it without interruption to the system Power supplying from consolidated power supply unit Product name Server chassis Product code N8141-49F Number of sever slots 20 40x 1000BASE-T LAN connector (1000BASE-T/100BASE-TX/10BASE-T, RJ-45, 40x Back, 2 port per server) Interface 1x Management LAN connector (100BASE-TX/10BASE-T, RJ-45, 1x Back, shared w ith 20 server) Redundant Fan supported, Hot plug Cooling Fan Up to 10 servers: standard / 11 to 20 servers : optional Power connector 1x Propriety 12VDC connector Chassis formfactor 3U rackmount Dimensions(W x D x H) 444.0 x 701.5 x 130.0 mm (Excluding inner rail), 466.0 x 724.5 x 130.0 mm (Including inner rail) Weight(min./max.) *1 22kg / 42kg Power consumption(12VDC, min./max.) *1 52W / 610W Power consumption(100VAC, Operating) 2091VA / 2063W Temperature , Relative Humidity Operating: 10 to 40°C/Non-Operating: -10 to 55°C, 20 to 80%(non condensation) EXPRESSBUILDER (NEC ESMPRO Manager, Users guide(PDF)), SUV cable(0.3m),Tool-less slide Included Accessories rail kit Note: *1 Minimum configuration: No servers and no optional fan box, Maximum configuration: 20 serves and 2 optional fan box included Specification (Consolidated PSU) Outline The power supply unit providing electrical power to many servers. Features Equips high efficient 80 PLUS® Gold power supply module. Supports up to 4 power module with hot plug and redundant feature Enables to supply electrical power for 80 servers per 1 consolidated power supply unit Enables to manage the consolidated power supply unit from remote site. Product name Power bay Product code N8142-36F 1x Serial(RS-232C, 9-pin mini-Dsub, Port B, 1x Front), 1x VGA (15-pin mini-Dsub, 1x Front) Interface 2x USB2.0 (2x Front), 1x Management LAN connector (100BASE-TX/10BASE-T, RJ-45) Number of Power supply Input(AC) Standard : 2 / Max : 4 Power module Redundant PSU Supported (needed more than 2 power modules, hot plug) 650W 80 PLUS® Gold Power supply (hot plug) Type 100-240 VAC±10%,50/60Hz±3Hz Output(DC) Pow er connector 4x Propriety 12VDC connector Max. output 1,700W *2 Power consumption(100VAC, Operating) 2091VA / 2063W Redundant Fan supported, Hot plug Cooling Fan Up to 10 servers: standard / 11 to 20 servers : optional Power connector 4x Propriety 12VDC connector Chassis formfactor 1U rackmount Dimensions(W x D x H) 444.0 x 671.0 x 43.5 mm (Excluding inner rail), 465.6 x 718.0 x 43.5 mm (Including inner rail) Weight(min./max.) *1 13kg / 15kg Temperature , Relative Humidity Operating: 10 to 40°C/Non-Operating: -10 to 55°C, 20 to 80%(non condensation) Included Accessories Getting started,Tool-less slide rail kit Note: *1 Minimum configuration: 2 power module, Maximum configuration: 4 power module *2 The maximum output per 1 DC connector can not exceed 840W. NEC Corporation 4th Edition, April 2011 4 System Configuration Guide Express5800/E110b-M External view (Express5800/E110b-M) Front view Power On/ Power LED Standby switch HDD access LED DUMP(NMI) switch Status LED UID(Unit ID) LED UID(Unit ID) switch SUV connector Lever Pull-out tab NEC Corporation 4th Edition, April 2011 5 System Configuration Guide Express5800/E110b-M External view (Server chassis) Front view Server slots Pull-out tab Rear view Fax box slots Management LAN DC 12V input connector port LAN port A for servers LAN port B for servers NEC Corporation 4th Edition, April 2011 6 System Configuration Guide Express5800/E110b-M External view (Consolidated PSU) Front view Pull-out tab Serial connector USB (Port B) VGA connector connector Power button UID(Unit ID) STATUS LED Maintenance LED LED UID(Unit ID) button Maintenance Power LED button Rear view UID(Unit ID) Power supply module bay UID(Unit ID) LED button DC output Pull-out tab Management connector LAN connector DC output button DC output LED NEC Corporation 4th Edition, April 2011 7 System Configuration Guide Express5800/E110b-M Outline drawing / Images (E110b-M) Outline drawing m t r m on 4 r ea . F R 119 441.2 mm m m m m 453.5 mm 1 5 . 22 19 Image (Interior view) NEC Corporation 4th Edition, April 2011 8 System Configuration Guide Express5800/E110b-M Outline drawing / Images (Server chassis) Outline drawing m m t m m r 0 0 .