ATTACHMENT C – 4FWPS MAOS STRIPER KIT INDIVIDUAL ITEM SPECIFICATIONS

This specification is approved for use by all Departments and Agencies of the Department of Defense within the distribution limitations noted at the bottom of the page.

C1. BACKGROUND

C1.1. Scope. This technical characteristics describes the requirements for procuring the required Minimum Airfield Operating Surfaces (MAOS) paint striper equipment, , material, consumables and the ISO container for the MAOS paint striper kit, needed to repaint the MAOS for sorties operations in support of rapid airfield damage recovery.

C2. MAOS PAINT STRIPER TECHNICAL REQUIREMENTS

C2.1. Paint Striper General Requirements.

C2.1.1. Paint striper unit shall be capable of applying reflectorized lines, one color at a time, up to a 36-in wide line in a single pass, skip or solid.

C2.1.2. Paint striper unit shall be equipped with an airless spray system for paint and a pressurized tank for reflective beads.

C2.1.3. Paint striper unit shall be a two-person operation (one truck driver and one operator on the rear of the unit). Due to the desire for a quality line and for safety reasons, one-person operation will NOT be acceptable.

C2.1.4. Completed paint striper unit shall be palletized and of legal size and weight to be compliant with all rules and regulations pertaining to a heavy duty 3/4-ton pickup truck or flatbed truck. Requirement of a 1-ton truck or larger IS NOT acceptable.

C2.1.5. Valves shall be labeled with 10 gauge stainless steel tags for function and operation as listed below. The text of the labels must be cut completely through the material. Etching the surface is NOT acceptable. The steel tags are to be 2- in x 3-in in size located on each high pressure (HP) return tube which read “FROM FILTER B” and “FROM FILTER A”. Two of the same tags shall be located on the valves going into the rear manifold. There are to be two similar tags located on the suction tubes that read “TO FILTER B” and “TO FILTER A”. There shall be bolted plates at the air drops which read “AIR 125 pounds per square inch (PSI) MAX”. The plate to which the filters mount should have “FILTER A” and “FILTER B” cut in with arrows pointing toward the respective filter. The low pressure (LP) cross over valves should have plates labeled with the valve positions. These shall be the same for both valve and read “BYPASS A”, “NO BYPASS”, and “BYPASS B”.

C2.2. Paint Striper Frame.

C2.2.1. Unit shall be installed on a palletized skid mount and must fit inside a standard 8-ft pickup truck bed. Drum holders shall be located directly behind driver’s cab.

C2.2.2. Frame rail shall be constructed of formed steel channel with cross members for support. Construction shall be of tab and slot construction welded at joints.

C2.2.3. Bead tank shall be mounted on the right side rear of the frame and cross member for convenient filling.

C2.2.4. Unit shall be held in truck bed by means of a zinc plated, tie down brackets with turnbuckles on rear bumper. If placed on flatbed truck, unit to be held down by securing to four (4) or more D-Rings on the sides of the unit (minimum two (2) per side). The contractor shall provide turnbuckles and restraints for both configurations; to include part numbers/NSN; descriptions, and weights.

C2.2.5. Operator’s platform shall be constructed with minimum of 1/8-in steel with non-skid design. Frames without an operator’s platform will NOT be accepted. Expanded metal deck NOT acceptable.

C-1

C2.2.6. Ladder with post and grab handle mounted to right rear of unit for easy access to operator platform. Ladder shall folded up for clearance. Post and grab handle shall be mounted near ladder.

C2.3. Fork Pockets for Paint Striper Frame.

C2.3.1. A separate fork pocket frame shall bolt to the underside of the main frame. Fork pockets shall be constructed of 4-in x 10-in x 3/16-in wall tube and shall be arranged so the frame may be forked from any of the four sides. The fork spacing shall be 38-in on center. The open space between the tubes on the frame shall be filled in with un- flattened expanded metal.

C2.3.2. There shall be a 6-in x 6-in x 12-in mounted at the right rear of the frame. The lid shall hinge and latch freely. It shall be durable enough to serve as a step.

C2.4. Paint Supply.

C2.4.1. Paint striper unit shall be capable of drawing paint from drum assembly. Drum assembly shall be capable of holding two (2) 55-gal drums. Paint striper unit shall be equipped with drum tie downs.

C2.4.2. There shall be two (2) stainless steel stirring paddle holders mounted in the corners of the drum holder assembly.

C2.5. Stand Tube. There shall be two (2) 4-in diameter x 40-in water-tight, leak proof tubes to hold the suction hose and bleeder line tubes and shall be mounted in a way they can be removed from the frame for ease of cleaning.

C2.6. Safety Guards. All moving belts and pulleys shall be enshrouded by metal guards.

C2.7. Motor Mount.

C2.7.1. Shall be constructed of 7-gauge steel and attached to frame by 7-gauge, -5-in channel supports.

C2.7.2. Hydraulic pump and air compressor shall have adjustable mounts for tightening of the drive belt.

C2.8. Gun Carriage.

C2.8.1. Gun carriage shall be single center wheeled, trailing from left rear of paint striper unit/truck. Forward mounted, vertical mounted, or push-style carriages will NOT be acceptable. The gun carriage shall have the capability to eliminate over spray during multi-color spraying operations.

C2.8.2. Wheel shall be 3.40/3.00-5 4 P.R. pneumatic tire with sealed roller bearings and a swivel caster. A pneumatic cylinder shall lift the carriage for transport and apply down pressure while striping.

C2.8.3. Four (4) carriage arms, shall each to be constructed of 1-in x 1-1/4-in (minimum) square tube. Pivot points on carriage shall have oil impregnated bushings.

C2.8.4. Carriage shall be attached to the slide mechanism by a heavy duty rigid mounting bracket.

C2.8.5. The bracket for the carriage mounting shall allow for bed heights of 30-in to 45-in from the ground.

C2.8.6. Carriage shall pivot upside down to allow the unit to sit flat on the ground for transport or storage.

C2.8.7. Gun mounts shall be adjustable to allow painting 2-in to 12-in lines with each gun (depending on tip size). All adjustable gun mount components shall be zinc plated. Adjustments shall be possible at all locations along gun bar. No predetermined incremental adjustment systems will be allowed.

C-2

C2.8.8. A pneumatically operated lift shall be provided to raise the carriage in and out of the transport position and to provide up to 30 psi of down pressure. The pneumatic lift shall be controlled by a lever located convenient to the operator. A regulator shall be provided to control the amount of down pressure being applied in the striping position. Hydraulic or cable lifts will NOT be allowed.

C2.8.9. Carriage lift cylinder shall be located on top side of carriage. Cylinder shall extend to let carriage down (striping position) and shall retract to lift carriage to transport/stow position. Pneumatic cylinder cannot lift from bottom side of carriage and shall extend to apply down pressure on carriage wheel. No exceptions.

C2.8.10. Outrigger tube shall be fitted with sliding pads made from UHMW plastic material to aid in steering.

C2.8.11. Carriage shall be hydraulically steerable with steering wheel operated from left side operator’s station for centerline operation.

C2.8.12. There shall be a cover over the carriage mounted solenoid bank for protection during wash-down.

C2.9. Seat Support Bracket.

C2.9.1. Seat shall be rigid mounted on left side of unit.

C2.9.2. Operator shall be able to adjust and lock seat orientation.

C2.9.3. Deluxe extra wide operator’s seat shall be provided with cushioned back rest and padded armrests with safety belt and weatherproof covering.

C2.10. Line Guide.

C2.10.1. Unit shall have mechanically adjustable line guide attached to front bumper of truck for use as a guidance by truck driver.

C2.10.2. The bumper brackets shall be adjustable to fit different style of truck bumpers. The brackets on the line guide that attach to the truck bumper shall be zinc plated. No exceptions.

C2.10.3. Main tube shall be at least 9-foot long with orange safety guide on end.

C2.10.4. Line guide shall be easily removable by removing two (2) pins with snap rings.

C2.10.5. Line guide shall be capable of being lifted to a 35-degree angle and secured in this position during transport to be fully visible to driver of vehicle.

C2.11. Battery Tray.

C2.11.1. Shall be located beneath engine. Shall be 8-in x 11-in, with 1-inclip constructed of 10-gauge steel welded to main frame.

C2.11.2. Battery shall be housed in a heavy duty polypropylene case, totally enclosed to be protected from weather with securing strap.

C2.12. Paint Striper Engine System.

C2.12.1.Engine shall have a minimum of 23 horse power industrial/commercial grade engine with electric start (with battery) and pull start option. The engine shall have the capability of powering the alternator, the air- compressor, and the hydraulic pump simultaneously during continuous operations of the paint striper.

C2.12.2. Paint striper unit shall have a 12-volt electric power supply with a minimum of a 16-amp alternator.

C-3

C2.12.3. Fuel tank shall meet California Air Resources Board (C.A.R.B.) plastic tank requirements.

C2.12.4. Engine shall be equipped with an hour meter to facilitate servicing.

C2.12.5. Pipe extension shall be provided on the drain out to allow oil to be easily drained.

C2.13. Air Supply System.

C2.13.1. Paint striper unit shall be equipped with a two-cylinder single stage,13.2-cfm displacement, air compressor with 2-gal reservoir, air filter system, unloader assembly, and a 50-cfm dryer w/auto drain, includes a float drain.

C2.13.2. Compressor shall unload when there is no demand for air. The compressor shall be equipped with a means to unload which allows the compressor to operate in a no load condition when the system is not demanding air (requires less power from engine and creates less heat while the system is idle). Compressor shall have means to unload head pressures once 115 psi is reached, and cut back in at 95 psi. Reservoir shall be isolated from compressor during cut out period.

C2.13.3. Safety valve shall be set at 150 psi and stamped with official ASME modified four-leaf clover symbol.

C2.13.4. There shall be an air manifold near the compressor; manufacturer’s recommendation of location.

C2.13.5. Manifold at the air compressor shall have a 0-300 psi liquid filled pressure gauge, 2-1/2-in minimum, and shall be visible from operator seat.

C2.13.6. Compressor shall have a pipe extension on the drain out for oil to be easily drained.

C2.13.7. Air supply hose to gun carriage shall be a nylon tube with solvent resistant neoprene cover.

C2.13.8. Air lines on gun carriage shall be solvent resistant nylon tubing to keep lines upright, and equipped with rugged corrosion resistant brass body push lock fittings to allow for easy replacement of air lines.

C2.13.9. 12-volt DC, 4.5 watt air solenoids shall be installed to activate each paint and bead gun. A separate air solenoid shall be supplied for each individual gun.

C2.13.10. Each set of solenoids shall be independently controlled from the control box and shall open one paint and bead gun.

C2.13.11. Solenoids provided shall be designed for rugged continuous duty and rapid cycling, full ported, and large capacity. Their flow shall be rated 10-CFM at 100-PSI with a pressure range of 0- to 125-PSI and temperature range 32- to 125-Fahrenheit.

C2.13.12. Quick connect air take-off shall be located at the rear of unit.

C2.13.13. Hose reel with 15-ft of air hose shall be mounted on the driver’s side of unit towards the front.

C2.14. Bead Supply System.

C2.14.1. Unit shall be equipped with one (1) 500-lbs capacity ASME approved tank for storage of reflectorized glass beads with a minimum of a 13-in fill opening. Smaller openings will NOT be accepted.

C2.14.2. The chemical and physical properties of all parts shall meet requirements for the specifications of the ASME Boiler and Pressure Vessel Code and certified by an authorized inspector of The National Board of Boiler and Pressure Vessel Inspectors.

C2.14.3. Tank shall be permanently labeled with modified four-leaf clover symbol of the ASME for 110-PSI maximum working pressure.

C-4

C2.14.4. Tank shall be steel with gasket head, safety pressure-release valve with the modified four-leaf clover symbol of the ASME, set to 110-PSI, and have a concave bottom for clean draining.

C2.14.5. Unit shall be complete with air regulator and gauge to adjust bead tank pressure from 5- to 60-PSI.

C2.14.6. A ball valve shall be installed on air supply hose at pressure regulator.

C2.14.7. 1-in bronze ball valve shall be installed at bottom of bead tank to stop bead flow from tank.

C2.14.8. Bead manifold shall be mounted at the bottom of the tank to divert flow of beads to individual bead supply hoses for each bead gun.

C2.14.9. 3/4-in ID bead supply hoses shall be clear PVC for visual flow, reinforced with a spring wire to be anti- collapsible, but with glass smooth interior to prevent material buildup. Hoses shall be rated at 70-PSI maximum at 70- Fahrenheit and shall be nontoxic.

C2.14.10. Three (3) Graco 238-338 (or equivalent) air activated glass bead dispensing guns to deliver glass beads at a rate of up to 20 pounds per minute. Four nozzle inserts for variable flow shall come standard with each bead gun. Air for atomization is NOT required.

C2.15. Hydraulic System.

C2.15.1. The hydraulic pump shall be a 10-gpm at 1800-rpm and 17-gpm at 3800-rpm rotary piston, pressure compensating pump with a swash plate for positive pressure control. Gear type pumps will NOT be acceptable. A hydraulic system that requires a cooler will NOT be acceptable.

C2.15.2. Hydraulic hoses shall have a -40- to 200-Fahrenheit temperature range with 4 to 1 safety factor, be oil/weather resistant, and have a minimum working pressure of 3,000-PSI.

C2.15.3. Hydraulic reservoir shall have a minimum 12-gal capacity, suction screen, temperature and level gauge, filter indicator, and color coded fill cap.

C2.15.4. There shall be a 10-foot hose plumbed to the bottom of the reservoir in order to drain the tank remotely.

C2.15.5. A 2-1/2-in minimum sized, liquid filled, 0-3,000-PSI, pressure gauge shall be provided at the high pressure paint pump.

C2.15.6. A hydraulic oil supply valve at the paint pump shall be rated at 2,000-PSI water- oil-gas (WOG).

C2.15.7. Hydraulic system shall contain a hydraulic oil in-line return filter containing a 10-micron element located inside the hydraulic reservoir. A service filter gauge shall be visible to operator. An internal suction side 100-micron filter shall be present. A magnet at the bottom of tank shall be present.

C2.15.8. The ratio of hydraulic system to paint system shall be 1:1 allowing pressure to be equal in the hydraulic lines and the paint lines. Other ratios will NOT be acceptable.

C2.16. Paint Supply System.

C2.16.1. The paint supply system shall be constructed to allow for the application of water base paint. All fluid wetted plumbing shall be stainless steel unless specified otherwise in this specification.

C2.16.2. There shall be two (2) high-pressure airless double ball piston paint pumps rated at 2,000-PSI at seven (7) cycles per gallon with a 60-cycle per minute recommended pump speed for continuous operation for a minimum delivery of 8.6-gpm each. Pumps to be Titan 989-120 (or equivalent).

C-5

C2.16.3. All wetted parts of the high pressure paint pump shall be water base compatible.

C2.16.4. Pumps shall have hard chrome plating on rod and cylinder parts for abrasion resistance. An 8-oz bottle of special pump lubricant shall be provided with the unit.

C2.16.5. Valve seats shall be carbide tungsten.

C2.16.6. Packings shall be spring loaded and self-adjusting. Pumps that have packings that are adjusted manually will NOT be accepted.

C2.16.7. Pressure and volume shall be fully adjustable.

C2.16.8. Shall have a foot valve at inlet, and shut-off valve on the outlet side of the paint pump.

C2.16.9. Pump shall have capability to recirculate the paint and shall be equipped with a pressure bleed valve.

C2.16.10. There shall be a 1-1/2-in x 10-in suction hose with a 40-in suction tube. The suction hose shall have a nylon tube core with solvent resistant neoprene cover.

C2.16.11. All hose fittings on the low pressure paint supply hoses and suction hose shall be stainless steel.

C2.16.12. 1-1/2-in supply hoses shall be valved at the pump inlet with stainless steel, ball valve.

C2.16.13. A high-pressure, spring-loaded check valve shall be installed at the outlet side of each pump. Check valve shall be stainless steel with stainless steel spring and metal to metal seat.

C2.16.14. Each high-pressure paint line shall have a stainless steel, full port ball valve at the pump outlet or at the high pressure paint filter.

C2.16.15. All high pressure ball valves shall be rated at 2,000PSI WOG working pressure or higher.

C2.16.16. All high pressure paint hoses which shall be water base compatible shall have a nylon core with thermoplastic cover reinforced with one braided layer brass plated steel wire of high tensile with national pipe threat (NPT) couplings without spring guards.

C2.16.17. 1/2-in hoses from paint pump to gun carriage shall have a 3,000- PSI working pressure with a burst pressure of 12,000-PSI.

C2.16.18. High pressure hoses shall be certified for electrostatic conductivity and hydrostatic resistance to a pressure of 1.5 times the working pressure stated on the hose.

C2.16.19. There shall be two (2) 6-in high-capacity, high pressure, 40-mesh, in-line filters which shall be water base compatible. Filters shall be located at the outlet of each pump. No exceptions. Stainless steel elements shall be accessible by removing a hand-tight threaded cap and lifting out for quick cleanup. Cap shall seal with Teflon washer with O-ring.

C2.16.20. Unit shall be equipped with three (3) Model 238-377 Graco (or equivalent) automatic airless spray guns rated at 4,000-PSI maximum working pressure and a forged aluminum gun body with stainless steel fluid passages.

C2.16.21. Each paint gun shall be equipped with an electric actuator controlled from the operator’s seated position. Each actuator shall change the elevation of the paint gun in relation to the pavement. The actuators shall adjust for paint viscosity changes and produce a wider or narrower line on the pavement without having to stop operations and readjust the gun height on the carriage. Actuators shall have a 6-inch stroke with 165-lbs. of force at .25-in/second velocity and 1.75-inch/second no load velocity. Actuators shall be controlled at operator station by one (1) double pole, double throw, center off, momentary switch per gun. Switches shall be resistant to moisture and dust.

C-6

C2.16.22. Paint guns shall be diaphragm air activated, requiring 40-60-PSI to operate. A complete paint gun repair kit shall be available to include the gun needle spring.

C2.16.23. Spray tip package shall be provided with XHD Reverse-A-Clean carbide tips that are inter-changeable for variable sized spray patterns and flow rates.

C2.16.24. Guns shall have a minimum flow rate of 3.3-gpm.

C2.16.25. There shall be one (1) 2-inch low pressure, in-line filter for each pump which shall be stainless steel for water-based compatibility. The hole openings shall be 1/8-inch.

C2.16.26. Low pressure filter shall be easy to access located right before the inlet to the high pressure pump.

C2.16.27. Pumps shall have low pressure crossover plumbing between pumps at the inlet so one or both pumps can draw from one drum or the other without moving the suction tubes.

C2.16.28. High pressure lines from both pumps shall be connected to a common manifold at the rear of the unit. Shall have two (2) quick connect fitting on manifold for optional hand gun and equipped with a manual gun switch controller.

C2.17. Electrical System.

C2.17.1. Power for the electrical system shall be provided by a 12-volt battery housed in a protective, heavy duty polypropylene case with tie-down strap.

C2.17.2. Shall have a main power switch for disconnecting electronics from battery.

C2.17.3. Wiring harness for electrical system shall follow standardized cable color coding

C2.17.4. Junction blocks at control box and on gun carriage shall be protected from the weather.

C2.17.5. Junction blocks shall be Underwriters Laboratory (UL) Listed rated at 30-amps or more.

C2.17.6. Wiring harness between junction blocks shall be protected by a polyethylene corrugated loom wire covering.

C2.17.7. Shrink tubing shall be used as a protective covering on wiring from cart junction box to the air solenoids.

C2.17.8. Shall include a David Clark 3800 intercom system (hard wired) or compatible equivalent with mounting accessories. Driver shall have single muff headset and operator to have dual muff headset.

C2.18. Gun Controller.

C2.18.1. The gun control device shall be a Skip-Line® MST-14 Mini Skip Timer or equivalent.

C2.18.2. The skip-setting mechanism shall be all electronic and shall utilize solid state components for all active internal functions. It shall process electrical pulses derived from the vehicle motion sensor and shall drive 12-volt, 2- amp solenoid valves. A means of inductive arc suppression shall be included. It shall require little or no maintenance. Clutches, cams, gears, or devices that require adjustment will not be allowed.

C2.18.3. All guns shall be operated by applying a ground signal to activate them.

C2.18.4. The skip-setting mechanism shall generate the selected repetitive pattern without utilizing any internal or external moving parts, except operator adjusted heavy duty robust sealed toggle switches for establishing pattern size, placement and calibration. Switches shall be of the three position, self-centering, center off type, and there

C-7 shall be long life sealed switch type push buttons for the CYCLE LENGTH adjustment, and the STRIPE LENGTH adjustment. Switches with thumb wheels or that have engraved digits shall not be acceptable.

C2.18.5. A full-color 4.3-in color LCD display shall be provided to display stripe, cycle and other striping parameters.

C2.18.6. The menu shall include the following:

C2.18.7. A Main screen that shall display current speed, an interactive pattern previewer, and active pattern modifiers.

C2.18.8. A Quick Setup menu, with the ability to enable or disable frequently used parameters of striping operations.

C2.18.9. A Counter Channels menu, which shall display application distance of all material guns, as well as material volume usage of all material pumps.

C2.18.10. A deep Setup menu, which shall allow advanced configuration of road marking patterns, applicator configuration, and other operational parameters. It shall also provide switch troubleshooting, pump life counters, and other maintenance and troubleshooting menus intended to decrease in-field down time.

C2.18.11. All indicator lamps must be solid state light-emitting diode types without filament which may burn out.

C2.18.12. The skip-setting system shall not use or require use of internal or external electromechanical relays.

C2.18.13. To conserve power the skip-setter shall draw less than 1/2-amp at 12-volts for internal circuits.

C2.18.14. For ease of operation the skip-setter shall have LCD display and shall provide pattern capability minimum of 1-ft, adjustable by 0.1-ft increments at any time whether at rest or in motion, without generating spurious patterns. When changing patterns, simple dial changes must suffice without resorting to “data complete” or “enter date” type controls. Also, “start” indexing (reset to zero) must be instantaneous. Shall be capable of switching from Standard to Metric readings on the fly.

C2.18.15. To aid in registration of new paint with previously paint pattern, the “ADVANCE” or “RETARD” (phase correction) system shall alter the pattern length no more than plus or minus 20% while activated. There shall be a means of AUTOMATICALLY adjusting the cycle length by 0.1-ft increments of one calibrated motion pulse if the advance or retard control is invoked three consecutive times.

C2.18.16. Basic electrical accuracy of the skip-setter shall be within 0.2-ft for any combination of the following factors:  Speed shall be adjustable from 1- to 50-mph.  Supply voltage shall be from 10- to 16-volts DC.  Temperature variations shall be from 0-F to 170-F.

C2.18.17. Shall be protected from accidental power surges caused by strobes, flashers, RPM change, solenoid or other equipment operations, etc.

C2.18.18. Operation of 2-way radio transmitters whether on board or nearby shall not cause generation of spurious painting patterns.

C2.18.19. Calibration shall be provided to ensure control dials agree with actual electrical output patterns. To reduce glare skip-setter shall be finished in flat black with a black front panel.

C2.18.20. The skip-setter shall provide a means to compensate for registration errors commonly found in application of paint and beads. Time delay controls shall be provided on master control panel of skip-setter to independently

C-8 activate “paint” and “beads” so they may be applied in registration with each other. Separate controls shall be provided to individually register leading and tailing ends of the pattern.

C2.18.21. The controller shall be capable of accurately displaying the speed of the striper in tenths of a mile per hour.

C2.19. Laser Guidance System. A laser guidance system shall be provided. The housing shall be securely magnet mounted to the roof of the chassis cab. A laser beam shall produce a visual spot (green in color) on the road edge, curb, existing line, etc. as a reference point for the gun carriages to follow. Power shall be supplied by the 12-volt vehicle. The laser housing shall be approximately 6-in in height, 12-in in length, 6-in in width, and shall weigh approximately 25-lbs. The laser shall be manually adjustable.

C2.20. Finish Coasting.

C2.20.1. Shall be one prime coat and one finish coat of a durable, chemical resistant paint.

C2.20.2. Shall be baked on powder coat finish.

C2.20.3. Shall be chrome, zinc plating, or galvanizing.

C2.20.4. Finish coat color shall be Isuzu white.

C2.21. Recommended Spare Parts. The contractor shall provide all paint striper manufacturer’s recommended spare part, maintenance, and accessory kits for the striper and related systems to include but not limited to hoses, paint guns and repair kits, valves, and engine maintenance components.

C2.22. Manual for palletized paint striper.

C2.22.1. Two sets (one printed and one electronic on a CD/DVD) of all operator’s/user’s manuals shall be provided. It should include:  Engine operator/maintenance manual  Air-composer operator/maintenance manual  Wiring diagram  Valve schematic, pneumatic  Value schematic, hydraulic  A section on general guidelines for striping  General operating ranges  Maintenance schedule  Flushing guideline  Maintenance record chart  Storage guidelines  Troubleshooting guide

C2.23. Warranty.

C2.23.1. All items furnished to meet these specifications shall be covered by the manufacturer’s and/or supplier’s standard warranty/guarantee on new equipment for one (1) year.

C2.24. Material and Workmanship.

C2.24.1. All equipment, materials and workmanship shall be the highest grade in accordance with industry standards.

C2.24.2. Equipment supplied will be new and unused except for the necessary testing, calibration and transportation.

C3. MAOS PAINT STRIPER STAND TECHNICAL REQUIREMENTS

C3.1. MAOS Paint Striper Stand. The contract shall either manufacture or procure a MAOS paint striper stand per

C-9 the Full Stand Assembly drawings/inventory on pages C-54 thru C-64. This stand is needed to store and secure the paint striper during shipment and long term storage of the MAOS paint striper kit. As well as, the stand (when removed from the ISO container) can be used as a maintenance stand before or after painting operations.

C4. MAOS PAINT STRIPER KIT COMPONENTS REQUIREMENTS

C4.1. Paint Striper Machine. One (1) EZ Liner AL120, is required in the MAOS Paint Striper Kit. This EZ Liner AL120, is required to be loaded into a truck to mark the newly layout MAOS for sorties operations during MAOS painting operations. EZ Liner AL120, shall be EZ Liner part# AL129 or equivalent (see C4.1.1.).

C4.1.1. Paint Striper Machine.  Palletized construction, self-container paint striper, must meet the specifications in Section C2.1. thru C2.25.2. of this attachment.

C4.2. MAOS Paint Striper Stand. One (1) MAOS paint striper stand, is required in the MAOS Paint Striper Kit. This MAOS paint striper stand, is required to store and secure the paint striper during shipment and long term storage of the MAOS paint striper kit. As well as, the stand (when removed from the ISO container) can be used as a maintenance stand before or after MAOS painting operations. The MOAS paint striper stand, shall be compatible. (see C4.2.1).

C4.2.1. MAOS Paint Striper Stand.  Contractor shall insure the MAOS paint striper stand, must meet the specifications in Section C3.1. of this attachment.

C4.3. Battery, 12-volt. One (1) battery, 12-volt, is required for the MAOS Paint Striper Kit. This battery, 12-volt, is used supply power to the paint striper before and during MAOS painting operations. The battery, 12-volt, shall be Deka part# 524MF or equivalent (see C4.3.1.).

C4.3.1. Battery, 12-volt property.  BCI Group 24, 12V  CCA 550 / CA 650  Reserve Capacity [min] 90 @ 25A  Positive terminal on left  Must be compatible with Item C4.1.

C4.4. Service Kit for Lamans 107F. One (1) service kit for Lamans 107F, is required for the MAOS Paint Striper Kit. This service kit for Lamans 107F, is used provide service/maintenance to specific parts of the paint striper before, during, or after MAOS painting operations. The service kit for Lamans 107F, shall be EZ Liner part# 050SKA or equivalent (see C4.4.1.).

C-10

C4.4.1. Service Kit for Lamans 107F property.  Must be compatible with Item C4.1.  Kit must consist of: o 1st and 2nd stage replacement elements o Cap and base gaskets o Base core

C4.5. Air Compressor Air Filter. One (1) air compressor air filter, is required for the MAOS Paint Striper Kit. This air compressor air filter, provides a replacement air compressor air filter for the paint striper before, during, or MAOS painting operations. The air compressor air filter, shall be EZ Liner part# 0043CH or equivalent (see C4.5.1.).

C4.5.1. Air compressor air filter property.  Must be compatible with Item C4.1.

C4.6. AL120, Bead Hose Assembly. One (1) AL120, bead hose assembly, is required for the MAOS Paint Striper Kit. This AL120, bead hose assembly, provides a replacement bead hose assembly for the paint striper before, during, or MAOS painting operations. The AL120, bead hose assembly, shall be EZ Liner part# 120-A175-00-B or equivalent (see C4.6.1.).

C4.6.1. AL120, bead hose assembly property.  Must be compatible with Item C4.1.

C4.7. Throat Seal Oil. One (1) throat seal, is required for the MAOS Paint Striper Kit. This throat seal oil, provides lubricate for the paint striper before, during, or after MAOS painting operations. The throat seal oil, shall be EZ Liner part# 206-995 or equivalent (see C4.7.1.).

C4.7.1. Throat seal oil property.  32-oz  OEM  Must be compatible with Item C4.1.

C4.8. Paint Gun. One (1) paint gun, is required for the MAOS Paint Striper Kit. This paint gun, provides an emergency replacement for the paint striper before, during, or after MAOS painting operations. The paint gun, shall be EZ Liner part# 238-377 or equivalent (see C4.8.1.).

C4.8.1. Paint gun property.  Must be compatible with Item C4.1.

C4.9. Paint Gun Repair Kit. Three (3) paint gun repair kits, are required for the MAOS Paint Striper Kit. These paint gun repair kits, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The paint gun, shall be EZ Liner part# 238-339 or equivalent (see C4.9.1.).

C4.9.1. Paint Gun Repair Kit property.  Must be compatible with Items C4.1. and C4.8.

C4.10. Bead Gun. One (1) bead gun, is required for the MAOS Paint Striper Kit. This bead gun, provides an emergency replacement for the paint striper before, during, or after MAOS painting operations. The bead gun, shall be EZ Liner part# 238-338 or equivalent (see C4.10.1.).

C4.10.1. Bead gun property.  Must be compatible with Item C4.1.

C-11

C4.11. Bead Gun Repair Kit. Three (3) bead gun repair kits, are required for the MAOS Paint Striper Kit. These bead gun repair kits, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The bead gun, shall be EZ Liner part# 238-340 or equivalent (see C4.11.1.).

C4.11.1. Bead Gun Repair Kit property.  Must be compatible with Items C4.1. and C4.10.

C4.12. Minor Pump Service Kit. One (1) minor pump service kit, is required for the MAOS Paint Striper Kit. This minor pump service kit, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The minor pump service kit, shall be EZ Liner part# 315-050 or equivalent (see C4.12.1.).

C4.12.1. Minor Pump Service Kit property.  Must be compatible with Item C4.1.

C4.13. Valve Foot. One (1) valve foot, is required for the MAOS Paint Striper Kit. This valve foot, provides an emergency replacement for the paint striper before, during, or after MAOS painting operations. The valve foot, shall be EZ Liner part# 317-925 or equivalent (see C4.13.1.).

C4.13.1. Valve Foot property.  Must be compatible with Items C4.1.

C4.14. Reset Assembly. One (1) reset assembly, is required for the MAOS Paint Striper Kit. This reset assembly, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The reset assembly, shall be EZ Liner part# 441-032A or equivalent (see C4.14.1.).

C4.14.1. Reset Assembly property.  Must be compatible with Item C4.1.

C4.15. HP Filter Springs. Three (3) HP filter springs, are required for the MAOS Paint Striper Kit. These HP filter springs, provides an emergency replacement for the paint striper before, during, or after MAOS painting operations. The HP filter springs, shall be EZ Liner part# 90408 or equivalent (see C4.15.1.).

C4.15.1. HP filter springs property.  Must be compatible with Item C4.1.

C4.16. Stainless Steel/HP Filter Ball. Three (3) stainless steel/HP filter balls, are required for the MAOS Paint Striper Kit. These stainless steel/HP filter balls, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The stainless steel/HP filter ball, shall be EZ Liner part# 90815 or equivalent (see C4.16.1.).

C4.16.1. Stainless steel/HP filter ball property.  Must be compatible with Item C4.1.

C4.17. HP Filter Gasket. Three (3) HP filter gaskets, are required for the MAOS Paint Striper Kit. These HP filter gaskets, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The HP filter springs, shall be EZ Liner part# 91447 or equivalent (see C4.17.1.).

C4.17.1. HP Filter gasket property.  Must be compatible with Item C4.1.

C4.18. Hydraulic Filter. Six (6) hydraulic filters, are required for the MAOS Paint Striper Kit. These hydraulic filters, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The hydraulic filter, shall be EZ Liner part# 93944-40 or equivalent (see C4.18.1.).

C4.18.1. Hydraulic filter property.

C-12

 Size: 40 Mesh  Must be compatible with Item C4.1.

C4.19. HP Filter Button Guide. Three (3) HP filter button guides, are required for the MAOS Paint Striper Kit. These HP filter button guides, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The HP filter button guide, shall be EZ Liner part# 93949 or equivalent (see C4.19.1.).

C4.19.1. HP filter button guide property.  Must be compatible with Item C4.1.

C4.20. Air Cylinder Advance. One (1) air cylinder advance, is required for the MAOS Paint Striper Kit. This air cylinder advance, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The air cylinder advance, shall be EZ Liner part# A21-01-1127 or equivalent (see C4.20.1.).

C4.20.1. Air cylinder advance property.  3-in Bore  6-in Stroke Advance  Must be compatible with Item C4.1.

C4.21. Filter Air Service Kit. One (1) filter air service kit, is required for the MAOS Paint Striper Kit. This filter air service kit, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The filter air service kit, shall be EZ Liner part# A28-02-1029 or equivalent (see C4.21.1.).

C4.21.1. Filter air service kit property.  Must be compatible with Item C4.1.

C4.22. Solenoid Air Valve M310. Six (6) solenoid air valves M310, are required for the MAOS Paint Striper Kit. These solenoid air valves M310, provide a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The solenoid air valve M310, shall be EZ Liner part# A54-01-1061or equivalent (see C4.22.1.).

C4.22.1. Solenoid air valve M310 property.  Must be compatible with Item C4.1.

C4.23. Suction Strainer. One (1) suction strainer, is required for the MAOS Paint Striper Kit. This suction strainer, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The suction strainer, shall be EZ Liner part# C28-01-3018 or equivalent (see C4.23.1.).

C4.23.1. Suction strainer property.  Must be compatible with Item C4.1.

C4.24. Hydraulic Filter. One (1) hydraulic filter, is required for the MAOS Paint Striper Kit. This hydraulic filter, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The hydraulic filter, shall be EZ Liner part# C28-02-3188 or equivalent (see C4.24.1.).

C4.24.1. Hydraulic filter property.  Size: 10 Micron  Must be compatible with Item C4.1.

C4.25. Sight Level for Temp. One (1) sight level for temp, is required for the MAOS Paint Striper Kit. This sight level for temp, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The sight level for temp, shall be EZ Liner part# C34-01-3023or equivalent (see C4.25.1.).

C4.25.1. Sight level for temp property.  Size: 5-in

C-13

 Must be compatible with Item C4.1.

C4.26. Paint Hose, 96-in Length x 1/2-in dia. One (1) paint hose, 96-in length x 1/2-in dia., is required for the MAOS Paint Striper Kit. This paint hose, 96-in length x 1/2-in dia., provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The paint hose, 96-in length x 1/2-in dia., shall be EZ Liner part# D40-08-4033 or equivalent (see C4.26.1.).

C4.26.1. Paint hose, 96-in length x 1/2-in dia. property.  Length: 96-in  Diameter: 1/2-in  High pressure  Must be compatible with Item C4.1.

C4.27. Paint Hose, 132-in Length x 1/2-in dia. One (1) paint hose, 132-in length x 1/2-in dia., is required for the MAOS Paint Striper Kit. This paint hose, 132-in length x 1/2-in dia., provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The paint hose, 132-in length x 1/2-in dia., shall be EZ Liner part# D40-08-4033 or equivalent (see C4.27.1.).

C4.27.1. Paint hose, 132-in length x 1/2-in dia. property.  Length: 132-in  Diameter: 1/2-in  High pressure  Must be compatible with Item C4.1.

C4.28. Paint Tank Vent. Four (4) paint tank vents, are required for the MAOS Paint Striper Kit. These paint tank vents, provide a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The paint tank vent, shall be EZ Liner part# D60-02-4013 or equivalent (see C4.28.1.).

C4.28.1. Paint tank vent property.  Top Mount  Must be compatible with Item C4.1.

C4.29. WYE Strainer Screen. Six (6) WYE strainer screens, are required for the MAOS Paint Striper Kit. These WYE strainer screens, provide a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The WYE strainer screen, shall be EZ Liner part# D72-02-4016 or equivalent (see C4.29.1.).

C4.29.1. WYE strainer screen property.  Must be compatible with Item C4.1.

C4.30. Actuator. One (1) actuator, is required for the MAOS Paint Striper Kit. This actuator, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The actuator, shall be EZ Liner part# G01-00-7223 or equivalent (see C4.30.1.).

C4.30.1. Actuator property.  Size: 75# Mini  12-Volt DC  6-in Stroke  Must be compatible with Item C4.1.

C4.31. Magnetic Cable. Ten (10) magnetic cables, are required for the MAOS Paint Striper Kit. These magnetic cables, provide a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The magnetic cable, shall be EZ Liner part# G53-00-7108 or equivalent (see C4.31.1.).

C4.31.1. Magnetic cable property.  Type: Sensor Logic

C-14

 Length: 25-ft  Must be compatible with Item C4.1.

C4.32. MST-14 Skip Timer System. One (1) MST-14 skip timer system, is required for the MAOS Paint Striper Kit. This MST-14 skip timer system, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The MST-14 skip timer system, shall be EZ Liner part# G63-01-7680 or equivalent (see C4.32.1.).

C4.32.1. MST-14 skip timer system property.  Must be compatible with Item C4.1.

C4.33. MST-14 Skip Timer System Harness. Two (2) MST-14 skip timer system harnesses, are required for the MAOS Paint Striper Kit. These MST-14 skip timer system harnesses, provide a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The MST-14 skip timer system harness, shall be EZ Liner part# G63-02-7681 or equivalent (see C4.33.1.).

C4.33.1. MST-14 skip timer system harness property.  Length: 15-ft  Must be compatible with Items C4.1. and C4.32.

C4.34. V-Belt, 52-in. One (1) V-Belt, 52-in, is required for the MAOS Paint Striper Kit. This V-Belt, 52-in, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The V-Belt, 52-in, shall be EZ Liner part# H09-00-8017 or equivalent (see C4.34.1.).

C4.34.1. V-Belt, 52-in property.  Type: Kevlar  Length: 52-in  Compatible from engine to air compressor  Must be compatible with Item C4.1.

C4.35. V-Belt, 50-in. One (1) V-Belt, 50-in, is required for the MAOS Paint Striper Kit. This V-Belt, 50-in, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The V-Belt, 50-in, shall be EZ Liner part# H09-00-8396 or equivalent (see C4.35.1.).

C4.35.1. V-Belt, 50-in property.  Type: Kevlar  Length: 50-in  Compatible from engine to hydraulic pump  Must be compatible with Item C4.1.

C4.36. Wheel/Roller Bearing. One (1) wheel/roller bearing, is required for the MAOS Paint Striper Kit. This wheel/roller bearing, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The wheel/roller bearing, shall be EZ Liner part# H69-01-8138 or equivalent (see C4.36.1.).

C4.36.1. Wheel/roller bearing property.  Size: 10-in  Must be compatible with Item C4.1.

C4.37. Pole Gun w/two (2) Wheel Carriage & 25-ft High Pressure Hose for Paint or Bead Assembly. One (1) pole gun w/two (2) wheel carriage & 25-ft high pressure hose for paint or bead assembly, is required for the MAOS Paint Striper Kit. This pole gun w/two (2) wheel carriage & 25-ft high pressure hose for paint or bead assembly, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The pole gun w/two (2) wheel carriage & 25-ft high pressure hose for paint or bead assembly, shall be EZ Liner part# 120- A312-00 or equivalent (see C4.37.1.). See Figure C4.37.

C-15

C4.37.1. Pole gun w/two (2) wheel carriage & 25-ft high pressure hose for paint or bead assembly property.  Assembly must include (Part #): o Pole Gun Assy, Indpendant Wheel (040-A040-00) or equivalent. o Hose Hanger Bracket (120-W0002-00) or equivalent. o Hose, 1/4-in x 25-ft, 3,300-psi, Blue (240-793) or equivalent. o Handle Grip, R-1200 Aux (D06-02-4039) or equivalent. o 1/2-in x 1/4-in HX NPL SS HP (T12-06-0804) or equivalent. o 1/4-in HX NPL SS HP 2 CHMF (T12-08-0404) or equivalent. o 1/4-in Ball Valve SS HP Stand Port (T12-60-0404) or equivalent. o Bolt, Hex, 5/16-in x 18 x 3/4-in Z5 (Z82-03-0512) or equivalent.  Must be compatible with Item C4.1.

Figure C4.37.

C4.38. Hand Gun w/25-ft High Pressure Hose (for Paint Only) Assembly. One (1) hand gun w/25-ft high pressure hose (for Paint Only) assembly, is required for the MAOS Paint Striper Kit. This hand gun w/25-ft high pressure hose (for Paint Only) assembly, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The hand gun w/25-ft high pressure hose (for Paint Only) assembly, shall be EZ Liner part# 120-A310-00 or equivalent (see C4.38.1.). See Figure C4.38.

C4.38.1. Hand gun w/25-ft high pressure hose (for Paint Only) assembly property.  Assembly must include (Part #): o Hose Hanger Bracket (120-W0002-00) or equivalent. o Hose, 1/4-in x 25-ft, 3,300-psi, Blue (240-793) or equivalent. o Handle Grip, R-1200 Aux (D06-02-4039) or equivalent. o 1/4-in Ball Valve SS HP Stand Port (T12-60-0404) or equivalent. o 1/4-in HX NPL SS HP 2 CHMF (T12-08-0404) or equivalent. o 1/2-in x 1/4-in HX NPL SS HP (T12-06-0804) or equivalent. o Bolt, Hex, 5/16-in x 18 x 3/4-in Z5 (Z82-03-0512) or equivalent. o Gun, Paint, Flex (005-900) or equivalent. o Tip, Spray, RAC V (286-425) or equivalent. o Graco 20-in Extension (232-122) or equivalent.  Must be compatible with Item C4.1.

C-16

Figure C4.38.

C4.39. Wind/Bead Deflector Assembly. One (1) wind/bead deflector assembly, is required for the MAOS Paint Striper Kit. This wind/bead deflector assembly, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The wind/bead deflector assembly, shall be EZ Liner part# 120-A182- 00 or equivalent (see C4.39.1.). See Figure C4.39.

C4.39.1. Wind/bead deflector assembly property.  Assembly must include (Part #): o CRG GUN BAR SQ TO RND BRKT (P) (043-W0004-00) or equivalent. o CRG GUN ACTU BRKT INSIDE (043-W061-00) or equivalent. o Bead Deflector (120-0000-15) or equivalent. o Screw, Cap, Hex, 1/4-in – 20 x 1/-1/2-in Z5 (Z82-03-0424) or equivalent. o Bolt, Hex, 5/16-in – 18 x 3/4-in Z5 (Z82-03-0512) or equivalent. o 1/4-in – 20 Hex Nut (Z82-40-0404) or equivalent. o Washer, Flat, 1/4-in Z5 (Z82-60-0404) or equivalent. o Washer, Lock Split, 1/4-in Z5 (Z82-66-0404) or equivalent. o 5/16-in – 18 Z5 Hex Nut (Z82-40-0505) or equivalent.  Must be compatible with Item C4.1.

Figure C4.39.

C-17

C4.40. Manual Gun Switch Controller. One (1) manual gun switch controller, is required for the MAOS Paint Striper Kit. This manual gun switch controller, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The manual gun switch controller, shall be EZ Liner part# G63-03-7856 or equivalent (see C4.40.1.).

C4.40.1. Manual gun switch controller property.  Must be compatible with Item C4.1.

C4.41. Oil Filter. Three (3) oil filters, are required for the MAOS Paint Striper Kit. These oil filters, provide a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The oil filter, shall be EZ Liner part# HON 15400-PLM-A01 or equivalent (see C4.41.1.).

C4.41.1. Oil filter property.  Height: 3.47-inches  Diameter: 2.69-inches  13 PSI Relief Valve  Must be compatible with Item C4.1.

C4.42. Fuel Filter. One (1) fuel filter, is required for the MAOS Paint Striper Kit. This fuel filter, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The fuel filter, shall be EZ Liner part# HON 16910-Z6L-003 or equivalent (see C4.42.1.).

C4.42.1. Fuel filter property.  Length: 4-inches  Diameter: 1.1-inches  Fits all GX Series Twin Cycler engines  Must be compatible with Item C4.1.

C4.43. Air Cleaner (filter). 14 air cleaners (filters), are required for the MAOS Paint Striper Kit. These air cleaners (filters), provide a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The air cleaner (filter), shall be EZ Liner part# HON 17210-Z6L-010 or equivalent (see C4.43.1.).

C4.43.1. Air cleaner (filter) property.  Diameter: 7-1/4-inches  Height: 2-inches  Washable foam pre-filter  Must be compatible with Item C4.1.

C4.44. Spark Plug. Two (2) spark plugs, are required for the MAOS Paint Striper Kit. These spark plugs, provide a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The spark plug, shall be EZ Liner part# 98079-5587G or equivalent (see C4.44.1.).

C4.44.1. Spark Plug property.  Thread Diameter: 14-milimeter  Reach: 19-milimeter  Size: 5/16-inch Hex Socket  Must be compatible with Item C4.1.

C4.45. Hydraulic Oil, 1-Gallon. Three (3) hydraulic oil, 1-gal containers, are required for the MAOS Paint Striper Kit. These hydraulic oil, 1-gal containers, provide a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The hydraulic oil, 1-gallon, shall be EZ Liner part# J31-00-0045 or equivalent (see C4.45.1.).

C4.45.1. Hydraulic oil, 1-gallon property.  ISO 68

C-18

 Container Size: 1 Gallon  Must be compatible with Item C4.1.

C4.46. Air Compressor Oil, 1-Gallon. One (1) air compressor oil, 1-gal container, is required for the MAOS Paint Striper Kit. This air compressor oil, 1-gal container, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The air compressor oil, 1-gallon, shall be EZ Liner part# J31- 00-0156 or equivalent (see C4.46.1.).

C4.46.1. Air compressor oil, 1-gallon property.  Container Size: 1 Gallon  Must be compatible with Item C4.1.

C4.47. Ball Valve. One (1) ball valve, is required for the MAOS Paint Striper Kit. This ball valve, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The ball valve, shall be EZ Liner part# T12-60-0808 or equivalent (see C4.47.1.).

C4.47.1. Ball valve property.  Size: 1/2-inch  Standard Port  SS/HP  Must be compatible with Item C4.1.

C4.48. Check Valve. One (1) check valve, is required for the MAOS Paint Striper Kit. This check valve, provides a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The check valve, shall be EZ Liner part# UN3-100-SSM-3.50 or equivalent (see C4.48.1.).

C4.48.1. Check valve property.  Size: 1-inch  SS/HP  Must be compatible with Item C4.1.

C4.49. Engine Oil, 1-Quart. 12 engine oil, 1-qt. containers, are required for the MAOS Paint Striper Kit. These engine oil, 1-qt. containers, provide a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The engine oil, 1-quart, shall be EZ Liner part# HON 08207-10W30 or equivalent (see C4.49.1.).

C4.49.1. Engine oil, 1-quart property.  10W30  Designed for 4-cycle engines  Resist viscosity and thermal breakdown  12 quarts = 1 case  Must be compatible with Item C4.1.

C4.50. Tip Guard, XHD-001. Three (3) tip guards, XHD-001, are required for the MAOS Paint Striper Kit. These tip guards, XHD-001, provide a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The tip guard, XHD-001, shall be EZ Liner part# XHD-001 or equivalent (see C4.50.1.).

C4.50.1. Tip guard, XHD-001 property.  For heavier coatings and materials  Maximum Pressure: 7,250 PSI  Single Screw Assembly  Must be compatible with Item C4.1.

C-19

C4.51. Spray Tip, XHD-635. Ten (10) spray tips, XHD-635, are required for the MAOS Paint Striper Kit. These spray tips, XHD-635, provide a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The spray tip, XHD-635, shall be EZ Liner part# XHD-635 or equivalent (see C4.51.1.).

C4.51.1. Spray tip, XHD-635 property.  Pattern Size: 12-inches to 14-inches  Flow Rate: 1.31-gallons per minute (gpm)  Must be compatible with Item C4.1.

C4.52. Spray Tip, XHD-835. Ten (10) spray tips, XHD-835, are required for the MAOS Paint Striper Kit. These spray tips, XHD-835, provide a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The spray tip, XHD-835, shall be EZ Liner part# XHD-835 or equivalent (see C4.52.1.).

C4.52.1. Spray tip, XHD-835 property.  Pattern Size: 16-inches to 18-inches  Flow Rate: 1.31-gallons per minute (gpm)  Must be compatible with Item C4.1.

C4.53. Spray Tip, XHD-935. Ten (10) spray tips, XHD-935, are required for the MAOS Paint Striper Kit. These spray tips, XHD-935, provide a repair/maintenance capability for the paint striper before, during, or after MAOS painting operations. The spray tip, XHD-935, shall be EZ Liner part# XHD-935 or equivalent (see C4.53.1.).

C4.53.1. Spray tip, XHD-935 property.  Pattern Size: 18-inches to 20-inches  Flow Rate: 1.31-gallons per minute (gpm)  Must be compatible with Item C4.1.

C4.54. Airless Paint Sprayer. One (1) airless paint sprayer, is required for the MAOS Paint Striper Kit. This airless paint sprayer, provides the ability to paint areas that are too confined to get the paint striper into during MAOS painting operations. The airless paint sprayer, shall be Panhandle Paint and Decorating part# 17C332 or equivalent (see C4.54.1.).

C4.54.1. Airless paint sprayer property.  Ultra Max II 490 PC Pro or equivalent.  1.0 Horse-Power Brushless DC Motor  Maximum PSI: 3,300 PSI

C4.55. Paint Tip, Airless Paint Sprayer. 20 paint tips, airless paint sprayer, are required for the MAOS Paint Striper Kit. These paint tips, airless paint sprayer, provide a repair/maintenance capability for the airless paint sprayer before, during, or after MAOS painting operations. The paint tip, airless paint sprayer, shall be Panhandle Paint and Decorating, part# 286621 or equivalent (see C4.55.1.).

C4.55.1. Paint tip, airless paint sprayer, 286621 property.  Pattern Size: 12-inches to 14-inches  Flow Rate: 1.31-gallons per minute (gpm)  Must be compatible with Item C4.54.

C4.56. Paint Tip, Airless Paint Sprayer. 20 paint tips, airless paint sprayer, are required for the MAOS Paint Striper Kit. These paint tips, airless paint sprayer, 286821, provides a repair/maintenance capability for the airless paint sprayer before, during, or after MAOS painting operations. The paint tip, airless paint sprayer, shall be Panhandle Paint and Decorating, part# 286821 or equivalent (see C4.56.1.).

C4.56.1. Paint tip, airless paint sprayer, 286821 property.  Pattern Size: 16-inches to 18-inches  Flow Rate: 1.31-gallons per minute (gpm)

C-20

 Must be compatible with Item C4.54.

C4.57. Power-stroke Paint Hose, 50-ft x 1/4-in. Six (6) power-stroke paint hoses, 50-ft x 1/4-in, are required for the MAOS Paint Striper Kit. These power-stroke paint hoses, 50-ft x 1/4-in, provides a repair/maintenance capability for the airless paint sprayer before, during, or after MAOS painting operations. The power-stroke paint hoses, 50-ft x 1/4-in, 286821, shall be Panhandle Paint and Decorating, part# ACPC050H or equivalent (see C4.57.1.).

C4.57.1. Power-stroke paint hose, 50-ft x 1/4-in property.  Length: 50-ft  Diameter: ¼-in  Maximum PSI: 3,300 PSI  Must be compatible with Item C4.54.

C4.58. Generator, 6kW, Diesel, w/Wheel Kit. One (1) generator, 6kW, Diesel, (NSN 8340-01-533-7678) w/Wheel Kit, is required in the MAOS Paint Striper Kit. This generator, is used to power all the electrical power tools in the MAOS paint striper kit during painting operations. The generator, 6kW, diesel, shall be HDT Global part # 62- GENSET6KW or equivalent (see C4.58.1.).

C4.58.1. Generator, 6kW, Diesel property.  Engine: Kohler KD420, 401 cc, 9 hp, 3600 rpm at 60 Hz or equivalent.  Output: Continuous – 5,000 W, Surge – 6,000 W, 120/240VAC, 60 Hz  120-volt receptacle: 4-NEMA 5-15 R receptacles w/CFCI protection & 1 NEMA L5-30R, 30 amp 3-wire twist-lock  240-volt receptacle: 1 NEMA 14-50R, 20 amp 4-wire  Fuel capacity: 4-gal  12-volt electric start w/built-in battery charger  Dimensions (L x W x H): 28-in x 22-in x 23-in  System weight: 207-lbs  Must include wheel set (C4.59.) and 12-volt battery

C4.59. Wheel Kit for Generator, 6kW, Diesel. One (1) wheel kit for generators, 6kW, Diesel, (NSN 8340-01-533- 7678), is required in the MAOS Paint Striper Kit. This wheel kit, allow for the easier movability during painting operations. The wheel kits, shall be HDT Global part # 62-GENSET6KW-WK or compatible equivalent.

C4.60. Battery, 12-Volt. One (1) battery, 12-volt, is required in the MAOS Paint Striper Kit. This battery, 12-volt, provides electric power to start the generator before, during, and after painting operations. The battery, 12-volt, shall be Duracell part# DURDC12-35J or equivalent.

C4.61. Cord, Extension, 50-Ft. Four (4) cords, extension, 50-ft, are required in the MAOS Paint Striper Kit. These cords, extension, 50-ft, are required to connect electric power from the generator to any electric power tool during painting operations. The cord, extension, 50-ft, shall be Home Depot part# 3043806-01 or equivalent (see C4.61.1.).

C4.61.1. Cord, extension, GFCI, 50-ft property.  Indoor/outdoor heavy duty extension cord,  One 3-way outlet  Gauge 14awg  3 conductor  15 amp rating  50 foot cord

C4.62. Fuel Can, Diesel, 5-Gal. Two (2) fuel can, diesel, 5-gal are required in the MAOS Paint Striper Kit. These fuel can, diesel, 5-gal are used fuel up various diesel powered equipment items within the MAOS paint striper kit,

C-21 before, during, and/or after painting operations. The fuel can, diesel, 5-gal, shall be Scepter part # SCE 05939 or equivalent (see C4.62.1.).

C4.62.1. Fuel can, diesel, 5-gal property.  Yellow Cap Strap  Mil-C-53109/CID A-A-59592A  Accepts pour spouts Item C4.64.

C4.63. Fuel Can, Gasoline (Mo-Gas), 5-Gal. Two (2) fuel can, gasoline (Mo-Gas), 5-gal are required in the MAOS Paint Striper Kit. These fuel can, gasoline (Mo-Gas), 5-gal are used fuel up various diesel and gasoline powered equipment items within the MAOS paint striper kit, before, during, and/or painting operations. The fuel can, gasoline (Mo-Gas), 5-gal, shall be Scepter part # SCE 5552 or equivalent (see C4.63.1.).

C4.63.1. Fuel can, gasoline (Mo-Gas), 5-gal property.  Red Cap Strap  Mil-C-53109/CID A-A-59592A  Accepts pour sprouts Item C4.64.

C4.64. Fuel Can, Spout, 1-in. Four (2) fuel can, spouts, 1-in are required in the MAOS Paint Striper Kit. These fuel can, spouts, 1-in are used in the refueling of various diesel and gasoline powered equipment items within the MAOS paint striper kit, before, during, and/or after painting operations. The fuel can, Spout, 1-in, shall be Scepter part # SCE 04353 or equivalent (see C4.64.1.).

C4.64.1. Fuel can, spout, 1-in property.  Size: 1-in  Must be compatible with Items C4.62. and C4.63.

C4.65. Saw, Reciprocating, 12-AMP, w/Case. One (1) saw, reciprocating, 12-amp, w/case (NSN 5130-00-819- 7767) is required in the MAOS Paint Striper Kit. This saw, reciprocating, 12-amp, is required cut various items and/or materials before, during, and/or painting operations. The saw, reciprocating, 12-amp, w/case, shall be Milwaukee part # MIL 6509-31 or equivalent (see C4.65.1.).

C4.65.1. Saw, reciprocating, 12-amp, w/case property.  Current: 12 AMP  Stroke Length: 3/4-in  Tool Length: 19-in  Weight: 7.1-lbs  Voltage: 120 V AC  Must include case

C4.66. Blade, Saw, Reciprocating, 5-pack. Three (3) blades, saw, reciprocating, 5-pack, are required in the MAOS Paint Striper Kit. These blades, saw, reciprocating, 5-pack, are used with saw, reciprocating to cut various items in support of painting operations. The blade, saw, reciprocating, 5-pack, shall be Milwaukee, part# 49-22-1105 or equivalent (see C4.66.1.).

C4.66.1. Blade, Saw, Reciprocating, 5-pack property.  Assorted (metal & wood cutting blades)  1-inch tall profile  Must be useable with Item C4.65.  5-pack

C-22

C4.67. Saw, Jig, Electric. One (1) saw, jig, electric, is required in the MAOS Paint Striper Kit. This saw, jig, electric, is required cut various items and/or materials before, during, and/or painting operations. The saw, jig, electric, shall be Milwaukee part # MIL 6268-21 or equivalent (see C4.67.1.).

C4.67.1. Saw, jig, electric property.  6.5-AMP Motor  1-inch stroke length  Blade: T-Shank  Variable speed trigger, 0 to 3,000 strokes per minute (spm)  4 position orbital cutting action  QUIK-LOK blade  Keyless shoe adjustment up to 45 degrees in both direction  Extra-long cord: 12-foot 8-inches  Must include case

C4.68. Blade, Jig Saw, 15-pack. Two (2) blades, jig saw, 15-pack, are required in the MAOS Paint Striper Kit. These blades, jig saw, 15-pack, are used with jig saw, to cut various items in support of painting operations. The blade, jig saw, 15-pack, shall be Milwaukee part# or equivalent (see C4.68.1.).

C4.68.1. Blade, jig saw, 15-pack property.  Assorted (metal & wood cutting)  Blade Type: T-Shank  Must be compatible with Item C4.67.  15-pack

C4.69. Drill, Electric, 1/2-in Drive. Two (2) drills, electric, 1/2-in drive, are required in the MAOS Paint Striper Kit. These drills, electric, 1/2-in drive, are required in support of painting operations. The drill, electric, 1/2-in drive, shall be Milwaukee part # MIL 0235-21or equivalent (see C4.69.1.).

C4.69.1. Drill, Electric, 1/2-in Drive property.  Electric  Corded  Tool Voltage: 120 Volt AC  Current: 5.5 AMPS  Chuck Size: 1/2-in  Keyless Chuck: Yes  Trigger Lock: Yes  Spindle: 1/2-in - 20  Gear Train: Double  Must include: side handle

C4.70. Spade Drill Bit Set. Two (2) spade drill bit sets, are required in the MAOS Paint Striper Kit. These spade drill bit sets, are used with the electric drill in support of painting operations. The spade drill bit set, shall be DeWalt part# DW1587 or equivalent (see C4.70.1.).

C4.70.1. Spade drill bit set property.  6-piece set  Size bits: 3/8-in to 1-in  1/4-in ball groove shank  Must be compatible with Item C4.69.

C-23

C4.71. Set, Drill & Driver, 45-piece. One (1) set, drill & driver, 45-piece, is required in the MAOS Paint Striper Kit. This set, drill & driver, 45-piece, is used with the electric drill in support of painting operations. The set, drill & driver, 45-piece, shall be Sun Coast Precision Tools part # MB-65944 (94090567) or equivalent (see C4.71.1.).

C4.71.1. Set, drill & driver, 45-piece property.  Drill & Driver Set 45 pieces of Quick Connect  Tool Bits 1/4-in Hex-shank  Magnetic Driver Bit Tip  135 Degree Split Point  Gold Oxide Coated  Includes case(s)  Must be compatible with Item C4.70.

C4.72. Hole Saw Kit. Two (2) hole saw kits, are required in the MAOS Paint Striper Kit. These hole saw kits, are used with the electric drill in support of painting operations. The hole saw kit, shall be Grainger part # 45EG81or equivalent (see C4.72.1.).

C4.72.1. Hole saw kit property.  7-piece set  Size bits: o 1-1/4-in o 1-3/8-in o 1-1/2-in o 1-3/4-in o 2-in o 2-1/8-in  Shank Size: 1/4-in hex  With plastic case  Must be compatible with Item C4.70.

C4.73. Saw, Circular, 7-1/4-in. One (1) saw, circular, 7-1/4-in (NSN 5130-01-455-6831), is required in the MAOS Paint Striper Kit. This saw, circular, 7-1/4-in, is required cut various items and/or materials before, during, and/or painting operations. The saw, circular, 7-1/4-in, shall be Milwaukee part # MIL 6390-20 or equivalent (see C4.73.1.).

C4.73.1. Saw, circular, 7-1/4-in property.  Electric  Corded  Tool Voltage: 120 Volt AC  Current: 15 AMPS  Blade Bevel: to 50 degrees  Arbor Size: 5/8-in  Blade Cutting Depth at 90 degrees: 2-7/16-in  Speed (RPM): 5,800

C4.74. Blade, Saw, Circular. Five (5) blades, saw, circular (NSN 5130-01-587-8182), are required in the MAOS Paint Striper Kit. These blades, saw, circular, are used with circular saw, to cut various items in support of painting operations. The blade, saw, circular, shall be MSC, part# FRE D0724X or equivalent (see C4.74.1.).

C4.74.1. Blade, Saw, Circular property.  Blade size: 7-1/4-in  Arbor size: 5/8-in  Teeth count: 24 tooth ATB carbide framing blade

C-24

 Dimensions: 7.25-in x 7.25-in x 0.31-in  Must be compatible with Item C4.73.

C4.75. Level, 24-in, Aluminum, w/Case. Two (2) levels, 24-in, aluminum, w/case (NSN 5210-00-239-0892), are required in the MAOS Paint Striper Kit. These levels, 24-in, aluminum, w/case, are used in support of painting operations. The level, 24-in, aluminum, w/case, shall be Kraft part# KRA SL2424C or equivalent (see C4.75.1.).

C4.75.1. Level, 24-in, aluminum, w/case property.  Dimensions: 24-in x 3-in x 2-in  Weight: 2.5-lbs  Aluminum  Must include plastic case

C4.76. Level, 72-in, Aluminum, w/Case. Two (2) levels, 72-in, aluminum, w/case, are required in the MAOS Paint Striper Kit. These levels, 72-in, aluminum, w/case, are used in support of painting operations. The level, 72-in, aluminum, w/case, shall be Kraft part# KRA SLSC4872 or equivalent (see C4.76.1.).

C4.76.1. Level, 72-in, aluminum, w/case property.  Length: 72-inches  Material: Aluminum I-beam  8 vials and 2 hand holds  Weight: 2.5-lbs  Must include plastic case

C4.77. Tape Measure, 300-ft. Three (3) tape measures, 300-ft, are required in the MAOS Paint Striper Kit. These tape measures, 300-ft, are used in support of painting operations. The tape measure, 300-ft, shall be Grainger part # 3VZG4 or equivalent (see C4.77.1.).

C4.77.1. Tape Measure, 300-ft property.  Length: 300 feet  Blade Material: Fiberglass  Blade Width: ½ inch  Accessories: Open Case w/ABS with Rubber Grips

C4.78. Measuring, Tape, Steel, 3/8-in x 100-ft, Closed. Three (3) measuring, tapes, steel, 3/8-in x 100-ft, closed (NSN 5210-01-357-4178), are required in the MAOS Paint Striper Kit. These measuring, tapes, steel, 3/8-in x 100- ft, closed, are used in support of painting operations. The measuring, tape, steel, 3/8-in x 100-ft, closed, shall be Grainger part # 6A500 or equivalent (see C4.78.1.).

C4.78.1. Measuring, tape, steel, 3/8-in x 100-ft, closed property.  Measurement Type: SAE  Blade Length: 100-ft  Blade Width: 3/8-in  Graduation Type: in & ft  Graduations: 1/8-in  Blade Material: Steel  Tip Style: Folding Hook  Case Type: Closed  Case Material: Vinyl  Belt Clip: Yes

C4.79. Measuring, Tape, Non-Magnetic, Single Hook, 1-in x 25-ft. Three (3) measuring, tapes, non-magnetic, single hook, 1-in x 25-ft, are required in the MAOS Paint Striper Kit. These measuring, tapes, non-magnetic, single

C-25 hook, 1-in x 25-ft, are used in support of painting operations. The measuring, tape, non-magnetic, single hook, 1-in x 25-ft, shall be Grainger part # 44ZJ77 or equivalent (see C4.79.1.).

C4.79.1. Measuring, Tape, Non-Magnetic, Single Hook, 1-in x 25-ft property.  Measurement Type: SAE  Blade Length: 25-ft  Blade Width: 1-in  Graduation Type: in & ft  Graduations: 1/16-in  Blade Material: Steel  Case Type: Closed  Case Material: ABS w/Rubber Grip  Belt Clip: Yes

C4.80. Measuring, Wheel. Two (2) measuring, wheels (NSN 5210-01-357-4178), are required in the MAOS Paint Striper Kit. These measuring, wheels, are used in support of painting operations. The measuring, wheel, shall be Grainger part # 2UJY6 or equivalent (see C4.80.1.).

C4.80.1. Measuring, wheel property.  Wheel Diameter: 12-in  Solid Aluminum Alloy Wheel  Fold Down Handle  Total Height: 36-in  Heavy Duty Steel Frame  5 Digit Counter  Measures up to 99,999-ft

C4.81. Framing Square. Two (2) framing squares, are required in the MAOS Paint Striper Kit. These framing squares, are used in support of painting operations. The framing square, shall be Lowe’s part # 118700 or equivalent (see C4.81.1.).

C4.81.1. Framing square property.  16-in x 24-in  Material: Aluminum  Precise impressed graduation

C4.82. Saw, Hand. Two (2) saws, hand, are required in the MAOS Paint Striper Kit. These saws, hand, are used in support of painting operations. The saw, hand, shall be Lowe’s part # 817731 or equivalent (see C4.82.1.).

C4.82.1. Saw, hand property.  Length: 20-in  Blade Material: Steel  Teeth Per Inch: 12  Cut Type: Cross-cutting

C4.83. Saw, Key Hole. Two (2) saws, key hole, are required in the MAOS Paint Striper Kit. These saws, key hole, are used in support of painting operations. The saw, key hole, shall be Lowe’s part # 324P312R or equivalent (see C4.83.1.).

C4.83.1. Saw, key hole property.  Blade type: 12-in carbon steel 8 TPI  Heat treated  Heavy-duty rubber grip handle

C-26

 Coarse cut

C4.84. Ratcheting Combination , 1-1/4-in. One (1) ratcheting combination wrench, 1-1/4-in, is required in the MAOS Paint Striper Kit. This ratcheting combination wrench, 1-1/4-in, is used in support of painting operations. The ratcheting combination wrench, 1-1/4-in, shall be Grainger part # 54PN38 or equivalent (see C4.84.1.).

C4.84.1. Ratcheting combination wrench, 1-1/4-in property.  Size: 1-1/4-inch, 12 Point  Finish: Full Polish  Open and box end  Standards: ASME B107.100-2017

C4.85. Ratcheting Combination Wrench Set, Metric, 17 pieces. One (1) ratcheting combination wrench set, metric, 17 pieces, is required in the MAOS Paint Striper Kit. This ratcheting combination wrench set, metric, 17 pieces, is used in support of painting operations. The ratcheting combination wrench set, metric, 17 pieces, shall be Grainger part # 54DG29 or equivalent (see C4.85.1.).

C4.85.1. Ratcheting combination wrench set, metric, 17 pieces property.  Sizes: 8-mm thru 25-mm, 12 Point  Finish: Full Polish  Open and box end  Standards: ASME B107.100-2017

C4.86. Ratcheting Combination Wrench Set, SAE, 15 pieces. One (1) ratcheting combination wrench set, SAE, 15 pieces, is required in the MAOS Paint Striper Kit. This ratcheting combination wrench set, SAE, 15 pieces, is used in support of painting operations. The ratcheting combination wrench set, SAE, 15 pieces, shall be Grainger part # 54DG22 or equivalent (see C4.86.1.).

C4.86.1. Ratcheting combination wrench set, SAE, 15 pieces property.  Sizes: 1/4-inch thru 1-inch, 12 Point  Finish: Full Polish  Open and box end  Standards: ASME B107.100-2017

C4.87. Open End Wrench, 1-1/4-in. One (1) open end wrench, 1-1/4-in, is required in the MAOS Paint Striper Kit. This open end wrench, 1-1/4-in, is used in support of painting operations. The open end wrench, 1-1/4-in, shall be McMaster Carr part# 5551A39 or equivalent (see C4.87.1.).

C4.87.1. Open end wrench, 1-1/4-in property.  For tight clearance  Opening Size: 1-1/4-inch  7-1/4-inch in length

C4.88. Open End Wrench, 1-1/2-in. One (1) open end wrench, 1-1/2-in, is required in the MAOS Paint Striper Kit. This open end wrench, 1-1/2-in, is used in support of painting operations. The open end wrench, 1-1/2-in, shall be McMaster Carr part# 5551A45 or equivalent (see C4.88.1.).

C4.88.1. Open end wrench, 1-1/2-in property.  For tight clearance  Opening Size: 1-1/2-inch  7-3/4-inch in length

C-27

C4.89. Open End Wrench, 1.625-in. One (1) open end wrench, 1.625-in, is required in the MAOS Paint Striper Kit. This open end wrench, 1.625-in, is used in support of painting operations. The open end wrench, 1.625-in, shall be McMaster Carr part# 5551A47 or equivalent (see C4.89.1.).

C4.89.1. Open end wrench, 1.625-in property.  For tight clearance  Opening Size: 1.625-inch  8-inch in length

C4.90. Open End Wrench, 1-3/4-in. One (1) open end wrench, 1-3/4-in, is required in the MAOS Paint Striper Kit. This open end wrench, 1-3/4-in, is used in support of painting operations. The open end wrench, 1-3/4-in, shall be McMaster Carr part# 5551A49 or equivalent (see C4.90.1.).

C4.90.1. Open end wrench, 1-3/4-in property.  For tight clearance  Opening Size: 1-3/4-inch  8-5/8-inch in length

C4.91. Open End Wrench, 2-in. One (1) open end wrench, 2-in, is required in the MAOS Paint Striper Kit. This open end wrench, 2-in, is used in support of painting operations. The open end wrench, 2-in, shall be McMaster Carr part# 5551A54 or equivalent (see C4.91.1.).

C4.91.1. Open end wrench, 2-in property.  For tight clearance  Opening Size: 2-inch  9-1/2-inch in length

C4.92. Wrench, Adjustable, 18-in. One (1) wrench, adjustable, 18-in, is required in the MAOS Paint Striper Kit. This wrench, adjustable, 18-in, is used in support of painting operations. The wrench, adjustable, shall be 18-in, Home Depot part# AC218VS or equivalent (see C4.92.1.).

C4.92.1. Wrench, adjustable, 18-in property.  18-in length  Jaw Capacity: 2-1/16-in or 53-mm  Heat-treated forged alloy steel  Tapered Handle

C4.93. Wrench, Adjustable, 12-in. One (1) wrench, adjustable, 12-in, is required in the MAOS Paint Striper Kit. This wrench, adjustable, 12-in, is used in support of painting operations. The wrench, adjustable, 12-in, shall be Home Depot part# AC212VS or equivalent (see C4.93.1.).

C4.93.1. Wrench, adjustable, 12-in property.  12-in length  Jaw Capacity: 1-1/2-in or 39-mm  Heat-treated forged alloy steel  Tapered Handle

C4.94. Wrench, Adjustable, 6-in & 8-in. Two (2) wrench, adjustable, 6-in & 8-in sets, are required in the MAOS Paint Striper Kit. These wrench, adjustable, 6-in & 8-in sets, is used in support of painting operations. The wrench, adjustable, 6-in & 8-in set, shall be Lowes part# 618459 or equivalent (see C4.94.1.).

C4.94.1. Wrench, adjustable, 6-in & 8-in property.  Length: 6-in and 8-in

C-28

 Black oxide resists rust and corrosion  SAE and Metric scale

C4.95. Wrench, Pipe, Adjustable, 2.5-in Capacity, 18-in Long. Two (2) , pipe, adjustable, 2.5-in capacity, 18-in long, are required in the MAOS Paint Striper Kit. These wrenches, pipe, adjustable, 2.5-in capacity, 18-in long, are used in support of painting operations. The wrench, pipe, adjustable, 2.5-in capacity, 18-in long, shall be Grainger part# 4A500 or equivalent (see C4.95.1.).

C4.95.1. Wrench, pipe, adjustable, 2.5-in capacity, 18-in long property.  Jaw Capacity: 2.5-in  Overall Length: 18-in  Handle Material: Cast Iron  Jaw Type: Serrated  Handle Type: I-Beam  Jaw Material: Steel  Feature: Floating Hook Jaw  Standards: Federal Specification GGG-N65IE, Type II Class A

C4.96. Wrench, Bung, Nylon, for Plastic & Metal Drums. Two (2) Wrenches, bung, nylon, for plastic & metal drums, are required in the MAOS Paint Striper Kit. These wrenches, bung, nylon, for plastic & metal drums, are used in support of painting operations. The wrench, bung, nylon, for plastic & metal drums, shall be Grainger part# BNW-P (5WAH0) or equivalent (see C4.96.1.).

C4.96.1. Wrench, bung, nylon, for plastic & metal drums property.  Overall length: 10-in  Material: Nylon

C4.97. Set, 16 pieces (Metric & SAE). One (1) nut driver set, 16 pieces (Metric & SAE), is required in the MAOS Paint Striper Kit. This nut driver set, 16 pieces (Metric & SAE), is used in support of painting operations. The nut driver set, 16 pieces (Metric & SAE), shall be Home Depot part# 202737877 or equivalent (see C4.97.1.).

C4.97.1. Nut driver set, 16 pieces (Metric & SAE) property.  16-piece set  Ratcheting and reversible  SAE Sizes: o 3/16-in o 1/4-inc o 5/16-in o 11/32-in o 3/8-in o 7/16-in o 1/2-in  Metric Sizes: o 5-mm o 6-mm o 7-mm o 8-mm o 9-mm o 10-mm o 11-mm o 12-mm

C-29

C4.98. Socket Set, 118 pieces (Metric & SAE). One (1) socket set, 118 pieces (Metric & SAE), is required in the MAOS Paint Striper Kit. This socket set, 118 pieces (Metric & SAE), is used in support of painting operations. The socket set, 118 pieces (Metric & SAE), shall be Milwaukee Tool part # 48-62-4177 or equivalent (see C4.98.1.).

C4.98.1. Socket set, 118 pieces (Metric & SAE) property.  118 piece SAE/Metric Socket Set  Chrome Vanadium Steel  Sizes: 1/4-in, 3/8-in, and 1/2-in drives  Must contain storage case

C4.99. Allen Key Set, 10 pieces (SAE). One (1) Allen key set, 10 pieces (SAE), is required in the MAOS Paint Striper Kit. This Allen key set, 10 pieces (SAE), is used in support of painting operations. The Allen key set, 10 pieces (SAE), shall be Home Depot part# 203195174 or equivalent (see C4.99.1.).

C4.99.1. Allen key set, 10 pieces (SAE) property.  10-piece SAE  T-handle  Sizes: 3/32-in through 3/8-in

C4.100. Allen Key Set, 8 pieces (Metric). One (1) Allen key set, 8 pieces (Metric), is required in the MAOS Paint Striper Kit. This Allen key set, 8 pieces (Metric), is used in support of painting operations. The Allen key set, 8 pieces (Metric), shall be Home Depot part# 206314470 or equivalent (see C4.100.1.).

C4.100.1. Allen key set, 8 pieces (Metric) property.  8-piece Metric  T-handle  Sizes: 2-mm through 10-mm

C4.101. Screw Driver Set, 15 pieces. One (1) screw driver set, 15 pieces, is required in the MAOS Paint Striper Kit. This screw driver set, 15 pieces, is used in support of painting operations. The screw driver set, 15 pieces, shall be Home Depot part# 204663546 or equivalent (see C4.101.1.).

C4.101.1. Screw driver set, 15 pieces property.  15-pieces  8 slotted screw drivers  7 Philips head drivers  Heat-treated alloy steel

C4.102. , Claw, 16-oz, Fiberglass Handle. Two (2) , claw, 16-oz, fiberglass handle (NSN 5120- 00-243-2959), are required in the MAOS Paint Striper Kit. These hammers, claw, 16-oz, fiberglass handle, are used in support of painting operations. The hammer, claw, 16-oz, fiberglass handle, shall be Grainger part # 2DGX4 or equivalent (see C4.102.1.).

C4.102.1. Hammer, claw, 16-oz, fiberglass handle property.  Heavy-duty claw hammer  Weight: 16-oz  Length: 13-in  Weight: 1.85-lbs  Handle Material: Non-Conductive

C4.103. Hammer, Ball Peen. Two (2) hammers, ball peen (NSN 5110-00-061-8546), are required in the MAOS Paint Striper Kit. These hammers, ball peen, are used in support of painting operations. The hammer, ball peen, shall be Grainger part # 53CT52 or equivalent (see C4.103.1.).

C-30

C4.103.1. Hammer, ball peen property.  Weight: 16-oz  Length: 12-1/2-in

C4.104. , Soft Surface. Two (2) , soft surface, are required in the MAOS Paint Striper Kit. These mallets, soft surface, are used in support of painting operations. The mallet, soft surface, shall be McMaster Carr part # 5913A5 or equivalent (see C4.104.1.).

C4.104.1. Mallet, soft surface property.  Soft surface mallet  Mallet Size: 1-3/4-inch face diameter  Overall Length: 13-1/2-inch  Material: UHMW Polyethylene Plastic

C4.105. Mallet, Hard Surface. Two (2) mallets, hard surface, are required in the MAOS Paint Striper Kit. These mallets, hard surface, are used in support of painting operations. The mallet, hard surface, shall be Grainger part # 22PN82 or equivalent (see C4.105.1.).

C4.105.1. Mallet, hard surface property.  Hard surface mallet  Mallet Size: 1-3/4-inch face diameter  Overall Length: 12-inches

C4.106. Hammer, Sledge, 3-lb. Two (2) hammers, sledge, 3-lb (NSN 5120-01-399-9252), are required in the MAOS Paint Striper Kit. These hammers, sledge, 3-lb, are used in support of painting operations. The hammer, sledge, 3-lb, shall be Grainger part # 48TE25 or equivalent (see C4.106.1.).

C4.106.1. Hammer, sledge, 3-lb property.  Handle Material: Glass fiber  Head weight: 3-lbs  Overall length: 14.0 inches nominal  Special feature: Non-slip cushion grip  Specification standard data: 05047-asme b107.54 professional/industrial association standard  Style designator: Sledge, blacksmith’s double faced

C4.107. Knife, Utility, Retractable, 6-in. Six (6) knives, utility, retractable, 6-in, are required in the MAOS Paint Striper Kit. These knives, utility, retractable, 6-in, are used in support of painting operations. The knife, utility, retractable, 6-in, shall be Grainger part # 4A803 or equivalent (see C4.107.1.).

C4.107.1. Knife, utility, retractable, 6-in property.  Length: 6-in  Features provided: retractable and blade storage in handle  Special Features: Includes 5 blades  Style designator: Shop removable blade

C4.108. Blade, Utility, Heavy Duty, 100-pack. Eight (8) blades, utility, heavy duty, 100-pack, are required in the MAOS Paint Striper Kit. These blades, utility, heavy duty, 100-pack, are used in support of painting operations. The blade, utility, heavy duty, 100-pack, shall be Stanley part# 11-921A or equivalent (see C4.108.1.).

C4.108.1. Blade, utility, heavy duty, 100-pack property.  Blade length: 2-7/16-in  Blade thickness: .024 inches nominal  Special features: Utility type; tapered with pointed ends

C-31

 With Dispenser

C4.109. Broom, Head, Polypropylene, 18-in, Acme Threaded Handled Connection. Two (2) brooms, head, polypropylene, 18-in, acme threaded handled connection, are required in the MAOS Paint Striper Kit. These brooms, head, polypropylene, 18-in, acme threaded handled connection, are used in support of painting operations. The broom, head, polypropylene, 18-in, acme threaded handled connection, shall be Grainger part# 2PYV4 or equivalent (see C4.109.1.).

C4.109.1. Broom, head, polypropylene, 18-in, acme threaded handled connection property.  Width: 18-in  Bristle Material: Polypropylene  Handle not included  Must be compatible with Item C4.110.

C4.110. Handle, Broom, 60-in, Acme Threaded. Two (2) handles, broom, 60-in, acme threaded, are required in the MAOS Paint Striper Kit. These handles, broom, 60-in, acme threaded, are used in support of painting operations. The handle, broom, 60-in, acme threaded, shall be Grainger part# 3H384 or equivalent (see C4.110.1.).

C4.110.1. Handle, broom, 60-in, acme threaded property.  Length: 60-in  Material: wood  Tip Length: 1-in  Must be compatible with Item C4.109.

C4.111. Broom, Dusting, Bench, 8-in x 3-in, Medium Bristle. Two (2) brooms, dusting, bench, 8-in x 3-in, medium bristle (NSN 7920-00-178-8315), are required in the MAOS Paint Striper Kit. These brooms, dusting, bench, 8-in x 3-in, medium bristle, are used in support of painting operations. The broom, dusting, bench, 8-in x 3-in, medium bristle, shall be Grainger part# 1XFL1 or equivalent (see C4.111.1.).

C4.111.1. Broom, dusting, bench, 8-in x 3-in, medium bristle property.  Brush material exposed length: 2.375 inches minimum and 2.750 inches maximum  Brush part length: 8-in  Brush part material: Horsehair, Tampico  Overall length: 13 1/4-in  Special features: Brush Bristle Firmness: Medium

C4.112. Dust Pan. Two (2) dust pans, are required in the MAOS Paint Striper Kit. These dust pans, are used in support of painting operations. The dust pan, shall be Home Depot part# 203883736 or equivalent (see C4.112.1.).

C4.112.1. Dust pan property.  Width: 12-in  Sturdy metal handle  Locks in open or closed position

C4.113. Floor Scraper. Two (2) floor scrapers, are required in the MAOS Paint Striper Kit. These floor scrapers, are used in support of painting operations. The floor scraper, shall be Grainger part# 2RMZ6 or equivalent (see C4.113.1.).

C4.113.1. Floor scraper property.  Size: 8-inch L x 1/2-inch W carbon steel blade  Handle: 56-inch in length  Handle Material: Steel/rubber  Includes blade cover

C-32

C4.114. Replacement Blades, Floor Scraper. One (1) replacement blades, floor scraper, are required in the MAOS Paint Striper Kit. These replacement blades, floor scraper, are used in support of painting operations. The replacement blades, floor scraper, shall be Grainger part# 2RMZ7 or equivalent (see C4.114.1.).

C4.114.1. Replacement blades, floor scraper property.  Size: 8-inch L x 1/2-inch W carbon steel blade  10-pack  Color: Black  Must fit and be usable with Item C4.113.

C4.115. Paint Scraper, 2-1/2-in. Five (5) paint scrapers, 2-1/2-in, are required in the MAOS Paint Striper Kit. These paint scrapers, 2-1/2-in, are used in support of painting operations. The paint scraper, 2-1/2-in, shall be Lowes part# 404814 or equivalent (see C4.115.1.).

C4.115.1. Paint scraper, 2-1/2-in property.  Blade Width: 2-1/2-in  Handle Length: 12-in  Blade Material: Steel  Handle: Impact- and solvent-resistant  Must be able to replace scraper blades  Secure thumb grip  Heavy duty applications

C4.116. Scraper Blades, Replacement, 2-1/2-in. Ten (10) scraper blades, replacement, 2-1/2-in, are required in the MAOS Paint Striper Kit. These scraper blades, replacement, 2-1/2-in, are used in support of painting operations. The scraper blades, replacement, 2-1/2-in, shall be Amazon part# 144900234 or equivalent (see C4.1165.1.).

C4.116.1. Scraper blades, replacement, 2-1/2-in property.  Tungsten Carbide Blade  Blade Size: 2-1/2-in  4-edge replacement blade  Must fit and be usable with Item C4.115.

C4.117. Paint Scraper, 4-in. Five (5) paint scrapers, 4-in, are required in the MAOS Paint Striper Kit. These paint scrapers, 4-in, are used in support of painting operations. The paint scraper, 4-in, shall be Lowes part# 845124 or equivalent (see C4.117.1.).

C4.117.1. Paint scraper, 4-in property.  Blade Width: 4-in  Handle Length: 9-in  Blade Material: Steel  Offset blade for optimum scraping angle  Must be able to replace scraper blades

C4.118. Scraper Blades, Replacement, 4-in. Two (2) scraper blades, replacement, 4-in, are required in the MAOS Paint Striper Kit. These scraper blades, replacement, 4-in, are used in support of painting operations. The scraper blades, replacement, 4-in, shall be Grainger part# 2RMZ7 or equivalent (see C4.118.1.).

C4.118.1. Scraper blades, replacement, 4-in property.  Blade width: 4-in  Hardened steel blade  5-pack

C-33

 Must fit and be usable with Item C4.117.

C4.119. Ladder. Two (2) ladders, are required in the MAOS Paint Striper Kit. These ladders, are used in support of painting operations. The ladder, shall be Lowes part# 935161 or equivalent (see C4.119.1.).

C4.119.1. Ladder property.  Multi-Position  Length: 18-ft  300-lb capacity

C4.120. Hose, Water, 5/8-in x 100-ft. Two (2) hoses, water, 5/8-in x 100-ft, are required in the MAOS Paint Striper Kit. These hoses, water, 5/8-in x 100-ft, are used in support of painting operations. The hose, water, 5/8-in x 100-ft, shall be Home Depot part# 100124440 or equivalent (see C4.120.1.).

C4.120.1. Hose, water, 5/8-in x 100-ft property.  Size: 5/8-in thick by 100-ft in length  400-PSI burst strength  Heavy duty coupling

C4.121. Nozzle, Water Hose. Three (3) nozzles, water hose (NSN 4730-00-595-1103), are required in the MAOS Paint Striper Kit. These nozzles, water hose, are used in support of painting operations. The nozzle, water hose, shall be Home Depot part# 100659525 or equivalent (see C4.121.1.).

C4.121.1. Nozzle, water hose property.  Insulated grip for water up to 160 degree F  Durable nozzle built for heavy-duty industrial applications  Must fit and be usable with Item C4.120.

C4.122. . Two (2) grease guns (NSN 4930-01-550-8352), are required in the MAOS Paint Striper Kit. These grease guns, are used in support of painting operations. The grease gun, shall be Home Depot part# 1056- LE4 or equivalent (see C4.122.1.).

C4.122.1. Grease gun property.  Heavy duty steel barrel and non-slip knurling  Electro-static, corrosion resistant coating  24-oz maximum

C4.123. Cone, Traffic, Safety, Orange, 18-in. 300 cones, traffic, safety, orange, 18-in, are required in the MAOS Paint Striper Kit. These cones, traffic, safety, orange, 18-in, are used in support of painting operations. The cone, traffic, safety, orange, 18-in, shall be MSA part# MSA10073409 or equivalent (see C4.123.1.).

C4.123.1. Cone, traffic, safety, orange, 18-in property.  Color: Bright Orange  Height: 18-in  Material: Polyethylene  Weight: 1.5-lb

C4.124. Gun, , Hex Rod, Parallel Frame. Three (3) guns, caulk, hex rod, parallel frame (NSN 5120-00-679- 5655), are required in the MAOS Paint Striper Kit. These guns, caulk, hex rod, parallel frame, are used in support of painting operations. The gun, caulk, hex rod, parallel frame, shall be Newborn part# NBR 112D or equivalent (see C4.124.1.).

C4.124.1. Gun, caulk, hex rod, parallel frame property.

C-34

 Weight: 1.88 lbs  Dimensions: 3-in x 9-in x 8-in

C4.125. 55-Gallon Drum w/lid. Eight (8) 55-gallon drums w/lids, are required in the MAOS Paint Striper Kit. These 55-gallon drums w/lids, are used in support of painting operations. The 55-gallon drum w/lid, shall be McMaster Carr part# 4115T44 or equivalent (see C4.125.1.).

C4.125.1. 55-Gallon drum w/lid property.  22-1/2inches Depth x 34-3/4-inches Height  Lever-lock closing ring with a 2-inch and 3/4-inch NPS openings  EPDM rubber gasket

C4.126. Sling, Drum, 55-Gallon. One (1) sling, drum, 55-gallon, is required in the MAOS Paint Striper Kit. This sling, drum, 55-gallon, is used in support of painting operations. The sling, drum, 55-gallon, shall be Grainger part# 39A384 or equivalent (see C4.126.1.).

C4.126.1. Sling, drum, 55-gallon property.  Material: Polyester webbing  Sling length: 30-inch  Maximum lifting capacity: 850-lbs

C4.127. , Drum, 55-Gallon. One (1) hand truck, drum, 55-gallon, is required in the MAOS Paint Striper Kit. This hand truck, drum, 55-gallon, is used in support of painting operations. The hand truck, drum, 55-gallon, shall be Grainger part# 34D647 or equivalent (see C4.127.1.).

C4.127.1. Hand truck, drum, 55-gallon property.  1,000-lb capacity  For use with 55-gallon steel drums

C4.128. Drum Handle/Bung Wrench, 55-Gallon. Two (2) drum handle/bung wrenches, 55-gallon, are required in the MAOS Paint Striper Kit. These drum handle/bung wrenches, 55-gallon, are used in support of painting operations. The drum handle/bung wrench, 55-gallon, shall be Home Depot part# 206298345 or equivalent (see C4.128.1.).

C4.128.1. Drum handle/bung wrench, 55-gallon property.  Ergonomic handle provides easy pushing/pulling of drums on a dolly  Rubber grips  Multipurpose tool, can open/close almost any size bung plugs

C4.129. , Drum, 55-Gallon. Six (6) , drum, 55-gallon, are required in the MAOS Paint Striper Kit. These funnels, drum, 55-gallon, are used in support of painting operations. The funnel, drum, 55-gallon, shall be Grainger part# 5PW06 or equivalent (see C4.129.1.).

C4.129.1. Funnel, drum property.  Size: 18-inch diameter  Chemical resistant HDPE  Screen included

C4.130. Spiral Mixing Arm. Five (5) spiral mixing arms, are required in the MAOS Paint Striper Kit. These spiral mixing arms, are used in support of painting operations. The spiral mixing arm, shall be Lowes part# 845139 or equivalent (see C4.130.1.).

C4.130.1. Spiral mixing arm property.

C-35

 Length: 30-in  Arbor Size: 1/2-in (must compatible with Item C4.69.)  Ribbon design ensures even mixing

C4.131. Traffic Paint, Black, 5-Gallon Bucket. 22 traffic paint, black, 5-gallon buckets, are required in the MAOS Paint Striper Kit. These traffic paint, black, 5-gallon buckets, are used in support of painting operations. The traffic paint, black, 5-gallon bucket, shall be Grainger part# 6GAN3 or equivalent (see C4.131.1.).

C4.131.1. Traffic paint, black, 5-gallon bucket property.  Color: Black  Viscosity: 80 to 90 Krebs Units  77% minimum solids and 100% Acrylic  Packaging: 5-gallon pail

C4.132. Traffic Paint, White, 5-Gallon Bucket. 22 traffic paint, white, 5-gallon buckets, are required in the MAOS Paint Striper Kit. These traffic paint, white, 5-gallon buckets, are used in support of painting operations. The traffic paint, white, 5-gallon bucket, shall be Grainger part# 6GAN1 or equivalent (see C4.132.1.).

C4.132.1. Traffic paint, white, 5-gallon bucket property.  Color: White  Viscosity: 80 to 90 Krebs Units  77% minimum solids and 100% Acrylic  Packaging: 5-gallon pail

C4.133. Traffic Paint, Yellow, 5-Gallon Bucket. 11 traffic paint, yellow, 5-gallon buckets, are required in the MAOS Paint Striper Kit. These traffic paint, yellow, 5-gallon buckets, are used in support of painting operations. The traffic paint, yellow, 5-gallon bucket, shall be Grainger part# 6GAN2 or equivalent (see C4.133.1.).

C4.133.1. Traffic paint, yellow, 5-gallon bucket property.  Color: Yellow  Viscosity: 80 to 90 Krebs Units  77% minimum solids and 100% Acrylic  Packaging: 5-gallon pail

C4.134. Glass Beads, Type 3, Airport, 50-lb Bags. 20 glass beads Type 3 airport, 50-lb bags, are required in the MAOS Paint Striper Kit. These glass beads, Type 3, airport, 50-lb bags, are used in support of painting operations. The glass beads Type 3, airport, 50-lb bags, shall be GB-09APIII or equivalent (see C4.134.1.).

C4.134.1. Glass beads, Type 3, airport, 50-lb bags property.  Must be compatible w/Item C4.1.

C4.135. Paint Roller Handle, 3-in. Ten (10) paint roller handles, 3-in, are required in the MAOS Paint Striper Kit. These paint roller handles, 3-in, are used in support of painting operations. The paint roller handle, 3-in, shall be Grainger part# 6LFG1 or equivalent (see C4.135.1.).

C4.135.1. Paint roller handle, 3-in property.  Length: 3-inch roller cover  Metal frame and plastic handle  Threaded handle for use with extension pole

C4.136. Roller Cover, 3-in (2-pack). 24 roller covers, 3-in (2-pack), are required in the MAOS Paint Striper Kit. These roller covers, 3-in (2-pack), are used in support of painting operations. The roller cover, 3-in (2-pack), shall be Grainger part# 48WL89 or equivalent (see C4.136.1.).

C-36

C4.136.1. Roller cover, 3-in (2-pack) property.  Length: 3-in  Nap: 3/8-in  Cover Material: Polyester  Paint Type: All  Surfaces: Semi-Smooth  2 per pack

C4.137. Paint Roller Handle, 9-in. Ten (10) paint roller handles, 9-in, are required in the MAOS Paint Striper Kit. These paint roller handles, 9-in, are used in support of painting operations. The paint roller handle, 9-in, shall be Grainger part# 3UW50 or equivalent (see C4.137.1.).

C4.137.1. Paint roller handle, 9-in property.  Length: 9-inch roller cover  Metal frame and plastic handle  Threaded handle for use with extension pole

C4.138. Roller Cover, 9-in (3-pack). Eight (8) roller covers, 9-in (3-pack), are required in the MAOS Paint Striper Kit. These roller covers, 9-in (3-pack), are used in support of painting operations. The roller cover, 9-in (3-pack), shall be Lowes part# 845139 or equivalent (see C4.138.1.).

C4.138.1. Roller cover, 9-in (3-pack) property.  Length: 9-in  Nap: 3/8-in  Cover Material: Polyester  Paint Type: Water Based and Oil Based  Surfaces: Smooth to Semi-Smooth  3 per pack

C4.139. Extension Handle, Paint Roller. Five (5) extension handles, paint roller, are required in the MAOS Paint Striper Kit. These extension handles, paint roller, are used in support of painting operations. The extension handle, paint roller, shall be Grainger part# 38UY15 or equivalent (see C4.139.1.).

C4.139.1. Extension handle, paint roller property.  Minimum Length: 4-foot  Maximum Length: 8-foot  Fiberglass and aluminum construction

C4.140. Brush, Paint, 2-in. 50 brushes, paint, 2-in, are required in the MAOS Paint Striper Kit. These brushes, paint, 2-in, are used in support of painting operations. The brush, paint, 2-in, shall be Grainger part# 38UX22 or equivalent (see C4.140.1.).

C4.140.1. Brush, Paint, 2-in property.  Brush width: 2-in  Handle size: 9/16-in x 2-7/16-in  Used with all paint and coatings

C4.141. Brush, Paint, 4-in. 50 brushes, paint, 4-in, are required in the MAOS Paint Striper Kit. These brushes, paint, 4-in, are used in support of painting operations. The brush, paint, 4-in, shall be Grainger part# 38UX23 or equivalent (see C4.141.1.).

C4.141.1. Brush, Paint, 4-in property.  Brush width: 4-in

C-37

 Handle size: 9/16-in x 2-7/16-in  Used with all paint and coatings

C4.142. Brush, Paint, 6-in. 50 brushes, paint, 6-in, are required in the MAOS Paint Striper Kit. These brushes, paint, 6-in, are used in support of painting operations. The brush, paint, 6-in, shall be Grainger part# 38UX31 or equivalent (see C4.142.1.).

C4.142.1. Brush, Paint, 6-in property.  6-inch Flat sash China hair  9/16-inch brush thickness  2-15/16-inch bristle length  All paints and coatings

C4.143. Bucket, Plastic, Utility, 5-Gal. 20 buckets, plastic, utility, 5-Gal (NSN 7240-01-411-0581), are required in the MAOS Paint Striper Kit. These buckets, plastic, utility, 5-gal, are used in support of painting operations. The bucket, plastic, utility, 5-gal, shall be US Plastics part# 3826 or equivalent (see C4.143.1.).

C4.143.1. Bucket, plastic, utility, 5-gal property.  Material: High density polyethylene construction  Stackable with lid  Color: White or Green

C4.144. Bucket, Lid, Plastic, Utility, 5-Gal. 20 bucket, lids, plastic, utility, 5-Gal (NSN 7240-01-411-0581), are required in the MAOS Paint Striper Kit. These bucket, lids, plastic, utility, 5-gal, are used in support of painting operations. The bucket, lid, plastic, utility, 5-gal, shall be US Plastics part# 2287 or equivalent (see C4.144.1.).

C4.144.1. Bucket, lid, plastic, utility, 5-gal property.  Material: High density polyethylene construction  Stackable with lid  Color: White or Green, must match C4.143.

C4.145. Paint Bucket Grid. Three (3) paint bucket grids, are required in the MAOS Paint Striper Kit. These paint bucket grids, are used in support of painting operations. The paint bucket grid, shall be Grainger part# 34AN87 or equivalent (see C4.145.1.).

C4.145.1. Paint Bucket Grid property.  Fits 5-gallon buckets  Mesh wrapped and reinforced on 4 sides

C4.146. Paint Tray. 20 paint trays, are required in the MAOS Paint Striper Kit. These paint trays, are used in support of painting operations. The paint tray, shall be Home Depot part# 100077262 or equivalent (see C4.146.1.).

C4.146.1. Paint tray property.  Solvent resistant metal tray  Holds up to 1-qt of paint or stain  Designed for 9-in paint rollers

C4.147. Paint Tray Liner. 75 paint tray liners, are required in the MAOS Paint Striper Kit. These paint tray liners, are used in support of painting operations. The paint tray liner, shall be Home Depot part# 205541527 (RM911) or equivalent (see C4.147.1.).

C4.147.1. Paint tray liner property.  Disposable

C-38

 Fits stand 9-in paint roller trays  Holds up to 1-qt of paint or stain

C4.148. Painter's Tape, 2-in. 15 painter's tape rolls, 2-in, are required in the MAOS Paint Striper Kit. These painter's tape rolls, 2-in, are used in support of painting operations. The painter's tape, 2-in, shall be Grainger part# 20JP24 or equivalent (see C4.148.1.).

C4.148.1. Painter's tape, 2-in property.  2-inch Wide x 60-yards Length  Crepe paper with rubber adhesive  Color: Off-white

C4.149. Painter's Tape, 4-in. 15 painter's tape rolls, 4-in, are required in the MAOS Paint Striper Kit. These painter's tape rolls, 4-in, are used in support of painting operations. The painter's tape, 4-in, shall be Grainger part# 20JP26 or equivalent (see C4.149.1.).

C4.149.1. Painter's tape, 4-in property.  4-inch Wide x 60-yards Length  Crepe paper with rubber adhesive  Color: Off-white

C4.150. Plastic Sheeting, 20-ft x 100-ft, 6mil, clear, roll. Six (6) plastic sheeting, 20-ft x 100-ft, 6mil, clear, rolls, are required in the MAOS Paint Striper Kit. These plastic sheeting, 20-ft x 100-ft, 6mil, clear, rolls, are used in support of painting operations. The plastic sheeting, 20-ft x 100-ft, 6mil, clear, roll, shall be MSC Direct part# 620100C or equivalent (see C4.150.1.).

C4.150.1. Plastic sheeting, 20-ft x 100-ft, 6mil, clear, roll property.  Item description: Polyethylene plastic;  Size: 20-ft x 100-ft  Thickness: 6-mil  Color: Clear

C4.151. Vinyl Tarp, 10-ft x 20-ft. One (1) vinyl tarp, 10-ft x 20-ft (NSN 8340-1-487-5610), is required in the MAOS Paint Striper Kit. This vinyl tarp, 10-ft x 20-ft, is used in support of painting operations. The vinyl tarp, 10- ft x 20-ft, shall be Tarp Supply part# X001P7KYFT or equivalent (see C4.151.1.).

C4.151.1. Vinyl tarp, 10-ft x 20-ft property.  Dimensions: 10-foot x 20-foot  Heavy Duty Poly  Weight: 5 to 6 ounces per square yard  Material: Waterproof, UV resistant, tear and mildew resistant

C4.152. Caulk, Case (Qty 12 per case). Two (2) caulk, cases (Qty 12 per case), are required in the MAOS Paint Striper Kit. These caulk, cases (Qty 12 per case), are used in support of painting operations. The caulk, case (Qty 12 per case), shall be Home Depot part# 100658164 or equivalent (see C4.152.1.).

C4.152.1. Caulk, case (Qty 12 per case) property.  White acrylic latex  Paintable with both latex and oil-based paints  Waterproof seal that maintains excellent flexibility  Tube size: 10.1 ounce  12 tubes per case

C-39

C4.153. Tyvek Suit, Large. Five (5) Tyvek suits, large, are required in the MAOS Paint Striper Kit. These Tyvek suits, large, are used in support of painting operations. The Tyvek suit, large, shall be Home Depot part# 203347773 or equivalent (see C4.153.1.).

C4.153.1. Tyvek suit, large property.  Size: Men’s Large  Protects cloths from spills and spatter; dry particles will not penetrate  Breathability reduces hazards of heat stress

C4.154. Tyvek Suit, Extra Large. Five (5) Tyvek suits, extra-large, are required in the MAOS Paint Striper Kit. These Tyvek suits, extra-large, are used in support of painting operations. The Tyvek suit, extra-large, shall be Home Depot part# 204739263 or equivalent (see C4.154.1.).

C4.154.1. Tyvek suit, extra-large property.  Size: Men’s Extra Large  Protects cloths from spills and spatter; dry particles will not penetrate  Breathability reduces hazards of heat stress

C4.155. Respirator, Particulate, N95, 20-pack. Five (5) respirator, particulate, N95, 20-packs (NSN 4240-1-463- 5449), are required in the MAOS Paint Striper Kit. These respirator, particulate, N95, 20-packs, are used in support of painting operations. The respirator, particulate, N95, 20-pack, shall be Grainger part# 2KJJ5 or equivalent (see C4.155.1.).

C4.155.1. Respirator, particulate, N95, 20-pack property.  Respirator Filter Class: N95  Nose Clip: Yes  Respirator Head strap Type: Dual, Non-Adjustable  Mask Size: Universal  20-pack

C4.156. Gloves, Disposable (X-Large) (U/I 100 ea). Five (5) gloves, disposable (x-large) (U/I 100 ea) (NSN 8415- 01-492-0180), are required in the MAOS Paint Striper Kit. These gloves, disposable (x-large) (U/I 100 ea), are used in support of painting operations. The gloves, disposable (x-large) (U/I 100 ea), shall be Grainger part# 1AV58 or equivalent (see C4.156.1.).

C4.156.1. Gloves, disposable (x-large) (U/I 100 ea) property.  Industrial Grade Vinyl  Lightly powered  5 mil  Clear  100 per box

C4.157. Towels, Paper, Shop, 200 count box. Eight (8) towels, paper, shop, 200 count box, are required in the MAOS Paint Striper Kit. These towels, paper, shop, 200 count box, are used in support of painting operations. The towels, paper, shop, 200 count box, shall be Kimberly Clark part# 75190 or equivalent (see C4.157.1.).

C4.157.1. Towels, paper, shop, 200 count box property.  Size: 10-in x 13-in  Pop-up box  Quantity per box: 200 count

C-40

C4.158. Shop Rags, 60-count. Five (5) shop rags, 60-count, are required in the MAOS Paint Striper Kit. These shop rags, 60-count, are used in support of painting operations. The shop rags, 60-count, shall be Home Depot, part# 391756 or equivalent (see C4.158.1.).

C4.158.1. Shop rags, 60-count property.  Material: Cotton terry  Size: 14-in x 17-in  Quantity per pack: 60 count

C4.159. Can, Trash, 55-Gal, Plastic. Two (2) cans, trash, 55-gal, plastic, are required in the MAOS Paint Striper Kit. These cans, trash, 55-gal, plastic, are used in support of painting operations. The can, trash, 55-gal, plastic, shall be Home Depot, part# 203883479 or equivalent (see C4.159.1.).

C4.159.1. Can, trash, 55-gal, plastic property.  Size: 55-gallon  Material: Plastic  Heavy duty construction with ergonomic handles

C4.160. Lid, Can, Trash, 55-Gal, Plastic. Two (2) lids, can, trash, 55-gal, plastic, are required in the MAOS Paint Striper Kit. These lids, can, trash, 55-gal, plastic, are used in support of painting operations. The lid, can, trash, 55- gal, plastic, shall be Home Depot, part# 203869144 or equivalent (see C4.160.1.).

C4.160.1. Lid, can, trash, 55-gal, plastic property.  Fits 55-gallon trash can (Item C4.158.)  Material: Plastic  Snap down locks and easy pull release  Must be compatible with C4.159.

C4.161. Odorless Mineral Spirits, 1-Gallon. Ten (10) odorless mineral spirits, 1-gallon containers, are required in the MAOS Paint Striper Kit. These odorless mineral spirits, 1-gallon containers, are used in support of painting operations. The odorless mineral spirits, 1-gallon container, shall be Home Depot, part# 204831509 or equivalent (see C4.161.1.).

C4.161.1. Odorless mineral spirits, 1-gallon container property.  No hazardous air pollutants or ozone depleting chemicals  Non-toxic  Container Size: 1-gallon

C4.162. Dish, Soap, Dawn, 1-Gallon. Eight (8) dish, soap, dawn, 1-gallon containers, are required in the MAOS Paint Striper Kit. These dish, soap, dawn, 1-gallon containers, are used in support of painting operations. The dish, soap, dawn, 1-gallon container, shall be Grainger part# 46F041 or equivalent (see C4.162.1.).

C4.162.1. Dish, soap, dawn, 1-gallon container property.  High sudsing  Ready to use  Size: 1 Gallon

C4.163. Spray-on Lubricant, 16-oz Can. 20 spray-on lubricant, 16-oz cans, are required in the MAOS Paint Striper Kit. These spray-on lubricant, 16-oz cans, are used in support of painting operations. The spray-on lubricant, 16-oz can, shall be Grainger part# 1MEU2 or equivalent (see C4.163.1.).

C4.163.1. Spray-on lubricant, 16-oz can property.  Synthetic and Non-flammable  Size Can: 16-ounce

C-41

 Contains PTFE

C4.164. String, Mason Line, Nylon, Fluorescent Yellow, 500-ft. Two (2) string, mason line, nylon, fluorescent yellow, 500-ft, are required in the MAOS Paint Striper Kit. These string, mason line, nylon, fluorescent yellow, 500-ft, are used in support of painting operations. The string, mason line, nylon, fluorescent yellow, 500-ft, shall be Grainger part# 21YH64 or equivalent (see C4.164.1.).

C4.164.1. String, mason line, nylon, fluorescent yellow, 500-ft property.  Rope Type: Tying & Bundling Rope  Rope Sub-Category: Twine  Rope Diameter: 3/64-in  Rope Material: Nylon  Rope Length: 500-ft  Working Load Limit: 132-lbs  Rope Construction: Braid  Package Type: Spool

C5. MAOS PAINT STRIPER KIT ISO CONTAINER REQUIREMENTS & COMPONENTS

C5.1. 20-ft ISO Container, Side Opening. One (1) 20-ft ISO container, side opening, is required for the MAOS Paint Striper Kit. This 20-ft ISO container, performs two (2) main functions, shipping and long term storage of the MAOS paint striper kit. The 20-ft ISO container, side opening, shall be NSN 8140-01-296- 7241 or equivalent (see C5.1.1.).

C5.1.1. 20-ft ISO container, side opening property.  Side Opening 20-Ft ISO Container shall have corrugated steel sides, roof, and swing doors one end and one side.  Side Opening 20-Ft ISO Container shall have a heavy-duty steel floor.  Side Opening 20-Ft ISO Container shall have four-way fork lift pockets.  Side Opening 20-Ft ISO Container shall be in good condition.  Side Opening 20-Ft ISO Container shall be the following dimensions: o Exterior Length – 19-ft, 10 1/2-in o Exterior Width – 8-ft o Exterior Height – 8-ft, 6-in o Interior Length – 19-ft, 4 13/64-in o Interior Width – 7-ft, 7 7/64-in o Interior Height – 7-ft, 5 61/64-in o End Doors (one end ONLY) Height – 7-ft, 1 7/64-in o End Doors (one end ONLY) Width – 7-ft, 6 13/64-in o Side Opening (one side ONLY) – Height – 7-ft, 0 13/64-in o Side Opening (one side ONLY) – Width – 19-ft 1 11/16-in  Side Opening 20-Ft ISO Container shall have dual swing doors on one end and dual swing doors on one side. Doors shall incorporate gaskets for a weatherproof seal when closed.  Side Opening 20-Ft ISO Container can be any color of TAN.  The contractor shall mark each Side Opening 20-Ft ISO Container according to the uniform procedures detailed in Defense Transportation Regulation (DTR) – Part VI, chapter 603 (paragraph 5).  Serial numbers shall be displayed on all four sides and on top of the Side Opening 20-Ft ISO Container.  ISO containers shall be weatherproof.  Maximum tare weight shall not exceed 6,613 lbs. and maximum payload capacity shall not exceed 46,297 lbs.  Side Opening 20-Ft ISO Container shall have vents, two (2) each in door panels.  Side Opening 20-Ft ISO Container shall be CSC certified and cargo worthy,.

C-42

C5.2. Wall Cabinet, 28-in x 14-in x 22-in. Four (4) wall cabinets, 28-in x 14-in x 22-in, are required for the MAOS Paint Striper Kit. These wall cabinets, 28-in x 14-in x 22-in, are used to store and secure various items, hand tools, equipment and/or consumables during shipment and long term storage. The l Wall Cabinet should be, 28-in x 14-in x 22-in or equivalent (see C5.21.).

C5.2.1. Wall cabinet, 28-in x 14-in x 22-in property.  28-in Wide x 14-in Deep x 22-in Height 2-in wide  Specifications are in Drawings Cabinet No. 1 on page C-68 of this attachment

C5.3. Wall Cabinet, 28-in x 22-in x 37.5-in w/five (5) drawers. One (1) wall cabinet, 28-in x 22-in x 37.5-in w/five (5) drawers, is required for the MAOS Paint Striper Kit. This wall cabinet, 28-in x 22-in x 37.5-in w/five (5) drawers, used to store and secure various items, hand tools, equipment and/or consumables during shipment and long term storage. The wall cabinet, 28-in x 22-in x 37.5-in w/five (5) drawers equivalent (see C5.3.1.).

C5.3.1. Wall cabinet, 28-in x 22-in x 37.5-in w/five (5) drawers property.  Size: 28-in Wide x 22-in Deep x 37.5-in Height  Has five (5) drawers  Specifications are in Drawings Cabinet No. 2 on page C-69 of this attachment

C5.4. Wall Cabinet, 28-in x 22-in x 37.5-in w/three (3) drawers. One (1) wall cabinet, 28-in x 22-in x 37.5-in w/three (3) drawers, is required for the MAOS Paint Striper Kit. This wall cabinet, 28-in x 22-in x 37.5-in w/three (3) drawers, used to store and secure various items, hand tools, equipment and/or consumables during shipment and long term storage. The wall cabinet should be, 28-in x 22-in x 37.5-in w/three (3) drawers or equivalent (see C5.4.1.).

C5.4.1. Wall cabinet, 28-in x 22-in x 37.5-in w/three (3) drawers property.  Size: 28-in Wide x 22-in Deep x 37.5-in Height  Has three (3) drawers  Specifications are in Drawings Cabinet No. 3 on page C-70 of this attachment

C5.5. Wall Cabinet, 30-in x 18-in x 75-in. One (1) wall cabinet, 30-in x 18-in x 75-in, is required for the MAOS Paint Striper Kit. This wall cabinet, 30-in x 18-in x 75-in, used to store and secure various items, hand tools, equipment and/or consumables during shipment and long term storage. The wall cabinet should be, 30-in x 18- in x 75-in or equivalent (see C5.5.1.).

C5.5.1. Wall cabinet, 30-in x 18-in x 75-in property.  30-in Wide x 18-in Deep x 75-in Height  Specifications are in Drawings Cabinet No. 4 on page C-71 of this attachment

C5.6. Flammable Storage Locker, 23-in x 18-in x 25-in. One (1) flammable storage locker, 23-in x 18-in x 25-in is required for the MAOS Paint Striper Kit. This flammable storage locker, 23-in x 18-in x 25-in, used to store and secure Hazardous materials before, during and after painting operations. The Flammable Storage Locker, 23-in x 18-in x 25-in, shall be GSA Advantage part# NSN 7125-01-516-8766 or equivalent (see C5.6.1.).

C5.6.1. Flammable Storage Locker, 23-in x 18-in x 25-in property.  Size: 23-in Wide x 18-in Deep x 35-in Height  Capacity 12-gallons  One adjustable shelf  Color: Yellow

C5.7. Basket, Wire, Bottom (48-in x 40-in x 42-in). Four (4) basket, wire, bottom (48-in x 40-in x 42-in), are required for the MAOS Paint Striper Kit. These basket, wire, bottom (48-in x 40-in x 42-in), used to store and secure various items, hand tools, equipment and/or consumables during shipment and long term storage and before, during and after painting operations. The basket, wire, bottom (48-in x 40-in x 42-in), shall be Nashville Wire, Part # WM- C-404836-222-HS-E or equivalent (see C5.7.1.).

C-43

C5.7.1. Basket, wire, bottom (48-in x 40-in x 42-in) property.  Collapsible steel large-capacity  Material: Zinc-plated steel  Four –way forklift entry  Length side half-drop door  Dimensions: 48-in long x 40-in wide x 42-in high  4,000-lbs capacity

C5.8. Ratchet Strap (2-in x 27-ft) w/Double J-Hooks. Four (4) ratchet straps (2-in x 27-ft) w/double j-hooks, are required for the MAOS Paint Striper Kit. These ratchet straps (2-in x 27-ft) w/double j-hooks, used to secure various items and equipment during shipment and long term storage. The ratchet straps (2-in x 27-ft) w/double j- hooks), shall be US Cargo Control part# 5027WH-Y or equivalent (see C5.8.1.).

C5.8.1. Ratchet straps (2-in x 27-ft) w/double j-hooks property.  Width: 2-in  Length: 27-ft  Ratchet Handle: Long Wide Handle  Assembly Break Strength: 10,000-lbs  Working Load Limit: 3,333-lbs  Webbing Break Strength: 12,000-lbs  End Fitting: Wire Hook  Color: Yellow

C5.9. Ratchet Strap (2-in x 12-ft) w/Double J-Hooks. Seven (7) ratchet straps (2-in x 12-ft) w/double j-hooks, are required for the MAOS Paint Striper Kit. These ratchet straps (2-in x 12-ft) w/double j-hooks, used to secure various items and equipment during shipment and long term storage. The ratchet straps (2-in x 127-ft) w/double j- hooks), shall be US Cargo Control part# 5512WHB-Camo or equivalent (see C5.9.1.).

C5.9.1. Ratchet straps (2-in x 12-ft) w/double j-hooks property.  Width: 2-in  Length: 12-ft  Ratchet Handle: Long Wide Handle  Assembly Break Strength: 10,000-lbs  Working Load Limit: 3,333-lbs  Webbing Break Strength: 12,000-lbs  End Fitting: Wire Hook  Color: Camo

C5.10. Chain, 3/8-in, Grade 70, 20-ft w/Grab Hooks. Four (4) chains, 3/8-in, Grade 70, 20-ft w/grab hooks, are required for the MAOS Paint Striper Kit. These chains, 3/8-in, Grade 70, 20-ft w/grab hooks, used to secure various items and equipment during shipment and long term storage. The chain, 3/8-in, Grade 70, 20-ft w/grab hooks, shall be US Cargo Control part # TC382070-D or equivalent (see C5.10.1.).

C5.10.1. Chain, 3/8-in, Grade 70, 20-ft w/grab hooks property.  Welding Type: Welded  For Lifting: Yes  Chain Link Style: Straight  Grade: 70  Trade Size: 3/8-in  Length: 20-ft  Assembly Break Strength: 26,400-lbs  Working Load Limit: 6,600-lbs  With Grab Hooks

C-44

C5.11. Chain, Ratchet Chain Binder, 3/8-in x 1/2-in, 9,200-lb. Four (4) chain, ratchet chain binders, 3/8-in x 1/2-in, 9,200-lb, are required for the MAOS Paint Striper Kit. These chain, ratchet chain binders, 3/8-in x 1/2-in, 9,200-lb, used to secure various items and equipment during shipment and long term storage. The chain, ratchet chain binder, 3/8-in x 1/2-in, 9,200-lb, shall be US Cargo Control part # CB275 or equivalent (see C5.11.1.).

C5.11.1. Chain, ratchet chain binder, 3/8-in x 1/2-in, 9,200-lb property.  Assembly Break Strength: 36,800-lbs  Working Load Limit: 9,200-lbs  Handle Length: 14-in  Material: Steel  Finish: Painted  Color: Red  Chain Size: 3/8-in  Grade 70 or 80

C5.12. Lock, Combination, Government. Three (3) locks, combination, government, are required for the MAOS Paint Striper Kit. These locks, combination, government, are used to secure both sets of doors on the QuadCon during shipment and long term storage. The lock, combination, government, (NSN 5340-00- 292-0896) or equivalent (see C5.12.1.).

C5.12.1. Lock, combination, government property.  Size: 5/16-in diameter, 2-1/4-in high, 1-in wide shackle.  2-in wide laminated steel body padlock.  Hardened steel shackle for extra cut resistance.  Combination change instructions and change tool included.  4-digit dialing allows for thousands of possible combinations.  Without chain.  Spec Number (CID): ASTM F883 A-A-1928

C6. ADDITIONAL MAOS PAINT STRIPER KIT ITEMS FOR RESUPPLY ONLY

C6.1. Additional MAOS Paint Striper Kit Items for Resupply Only. The nine (9) items below shall be made available for resupply ONLY as part of this IDIQ.

C6.1.1. Pole Gun w/two (2) wheel carriage. One (1) pole gun w/two (2) wheel carriage is for replacement, must be compatible w/Item C4.1., is required for resupply in support of the MAOS Paint Striper Unit Type Code (UTC). EZ-Liner, part# 040-A040-00 or equivalent, see Figure C6.1.1.

C-45

Figure C6.1.1.

C6.1.2. Hose Hanger Bracket for Pole Gun w/two (2) wheel carriage. One (1) hose hanger bracket for pole gun w/two (2) wheel carriage is for replacement, must be compatible w/Item C4.1 and C6.1.1, is required for resupply in support of the MAOS Paint Striper Unit Type Code (UTC). EZ-Liner, part# 120-W0002-00 or equivalent, see Figure C6.1.2.

Figure C6.1.2.

C6.1.3. Hose, 1/4-in x 25-ft, for Pole Gun w/two (2) wheel carriage. One (1) hose, 1/4-in x 25-ft, for pole gun w/two (2) wheel carriage is for replacement, must be compatible w/Item C4.1 and C6.11., is required for resupply in support of the MAOS Paint Striper Unit Type Code (UTC). EZ-Liner, part# 240-793 or equivalent (see Figure C6.1.3.1).

C6.1.3.1. Hose, 1/4-in x 25-ft, for Pole Gun w/two (2) wheel carriage property.  Diameter: 1/4-in  Length: 25-ft  Color: Blue  PSI Rating: 3,300

C6.1.4. Manual Laser Guidance, Assembly. One (1) manual laser guidance, assembly is for replacement, must be compatible w/Item C4.1., is required for resupply in support of the MAOS Paint Striper Unit Type Code (UTC). EZ-Liner, part# 120-A336-00 or equivalent (see C6.1.4.1). See Figure C6.1.4.

C6.1.4.1. Manual laser guidance, assembly property.  Assembly must include (Part #): o Man Pnt Stripe Laser (GL3000-PM) or equivalent. – Qty 1 o Laser Guidance Plug-In (0003-0322) or equivalent. – Qty 1 o Laser Guidance Magnet Mnt (3000-0135) or equivalent. – Qty 2 o 1/4-in-20 x 1-1/4-in Z5 HX Bolt (Z82-03-0420) or equivalent. – Qty 2 o 1/4-in Washer Flt Z5 (B) (Z82-60-0404) or equivalent. – Qty 2 o Washer Lock Split 1/4-in Z5 (Z82-66-0404) or equivalent. – Qty 2 o 1/4-in-20 Z5 HX Nut Finished (Z82-40-0404) or equivalent. – Qty 2

C-46

Figure C6.1.4.

C6.1.5. Seat, Assembly. One (1) seat, assembly is for replacement, must be compatible w/Item C4.1., is required for resupply in support of the MAOS Paint Striper Unit Type Code (UTC). EZ-Liner, part# TYN-A040-00 or equivalent (see 6.1.5.1). See Figure C6.1.5.

C6.1.5.1. Seat, assembly property.  Assembly must include (Part #): o Big Boy Seat Bracket (TYN-W040-00) or equivalent. – Qty 1 o AL20, Seat Collar Lock, 1.94-in (120-W040-01) or equivalent. – Qty 1 o Pin, Safety, 5/16-in x 2-1/4-in Lock, Sq, Clip (Z82-77-0534) or equivalent. – Qty 1 o Big Boy Seat w/Arms (H52-00-8421) or equivalent. – Qty 1 o 3/8-in-16 x 1/-1/4-in Grade 5 Hex Bolts or equivalent. – Qty 4 o vi. Washer, Flat, 3/8-in, Z5 (Z82-60-0606) or equivalent. – Qty 8 o 3/8-in-16 Z Grade C Nut Lock (B) (Z82-42-0606) or equivalent. – Qty 4

Figure C6.1.5.

C6.1.6. AL120, Line Guide, Assembly. One (1) AL120, line guide, assembly is for replacement, must be compatible w/Item C4.1., is required for resupply in support of the MAOS Paint Striper Unit Type Code (UTC). EZ-Liner, part# 120-A080-00 or equivalent (see 6.1.6.1). See Figure C6.1.6.

C-47

C6.1.6.1. AL120, line guide, assembly property.  Assembly must include (Part #): o AL120, Line Guide Pointer Assembly (120-A082-00 – Qty 1 o AL20, Line Guide Bracket Assembly (120-A083-00) – Qty 1

Figure C6.1.6.

C6.1.7. Headset (Single Muff), Communication. One (1) headset (single muff), communication is for replacement, must be compatible w/Item C4.1., is required for resupply in support of the MAOS Paint Striper Unit Type Code (UTC). EZ-Liner, part# H3492.

C6.1.8. Headset (Double Muff), Communication. One (1) headset (double muff), communication is for replacement, must be compatible w/Item C4.1., is required for resupply in support of the MAOS Paint Striper Unit Type Code (UTC). EZ-Liner, part# H3432.

C6.1.9. Communication Master Control Station. One (1) communication master control station is for replacement, must be compatible w/Item C4.1., is required for resupply in support of the MAOS Paint Striper Unit Type Code (UTC). EZ-Liner, part# U3800.

C7. IDIQ RESUPPLY UNIT OF ISSUE

C7.1. IDIQ Unit of Issue per Item for MAOS Paint Striper Kit. Table 1, shows what the unit of issue for each item in the MAOS paint striper kit listing, when NOT procured as a full kit.

TABLE 1. IDIQ Quantities per Item for MAOS Paint Striper Kit Item Unit of Issue EZ Liner AL120 1 each MAOS Paint Striper Stand 1 each Battery, 12-Volt 1 each Service Kit for Lamans 107F 1 each Air Compressor Air Filter 1 each AL120, Bead Hose Assembly 1 each Throat Seal Oil 1 each Paint Gun 1 each Paint Gun Repair Kit 1 each Bead Gun 1 each Bead Gun Repair Kit 1each Minor Pump Service Kit 1 each Valve Foot 1 each Reset Assembly 1 each HP Filter Springs 1 each Stainless Steel/HP Filter Ball 1 each HP Filter Gasket 1 each Hydraulic Filter 1 each

C-48

Item Unit of Issue HP Filter Button Guide 1 each Air Cylinder Advance 1 each Filter Air Service Kit 1 each Solenoid Air Valve M310 1 each Suction Strainer 1 each Hydraulic Filter 1 each Sight Level for Temp 1 each Paint Hose, 96-in Length x 1/2-in dia. 1 each Paint Hose, 132-in Length x 1/2-in dia. 1 each Paint Tank Vent 1 each WYE Strainer Screen 1 each Actuator 1 each Magnetic Cable 1 each MST-14 Skip Timer System 1 each MST-14 Skip Timer System Harness 1 each V-Belt, 52-in 1 each V-Belt, 50-in 1 each Wheel/Roller Bearing 1 each Pole Gun w/two (2) Wheel Carriage & 25-ft High Pressure 1 assembly Hose for Paint or Bead Assembly Hand Gun w/25-ft High Pressure Hose (for Paint Only) 1 assembly Assembly Wind/Bead Deflector Assembly 1 assembly Manual Gun Switch Controller 1 each Oil Filter 1 each Fuel Filter 1 each Air Cleaner (filter) 1 each Spark Plug 1 each Hydraulic Oil, 1-Gal 1 each Air Compressor Oil, 1-Gal 1 each Ball Valve 1 each Check Valve 1 each Engine Oil, 1-Qt 1 case of 12 Tip Guard, XHD-001 1 each Spray Tip, XHD-635 1 each Spray Tip, XHD-835 1 each Spray Tip, XHD-935 1 each Airless Paint Sprayer 1 each Paint Tip, Airless Paint Sprayer, 286621 1 each Paint Tip, Airless Paint Sprayer, 286821 1 each Power-stroke Paint Hose, 50-ft x 1/4-in 1 each Generator, 6kW, Diesel, w/Wheel Kit 1 each Wheel Kit, Generator, 6kW, Diesel 1 each Battery 12-Volt 1 each Cord, Extension, GFCI, 50-Ft 1 each Fuel Can, Diesel, 5-Gal 1 each Fuel Can, Gasoline (Mo-Gas), 5-Gal 1 each Fuel Can, Spout, 1-in 1 each Saw, Reciprocating, 12-AMP, With Case 1 each Blade, Reciprocating Saw, 5-pack 1 each Saw, Jig, Electric 1 each Blade, Jig Saw, 15-pack 1 each

C-49

Item Unit of Issue Drill, Electric, 1/2-in Drive 1 each Spade Drill Bit Set 1 each Set, Drill & Driver, 45-piece 1 each Hole Saw Kit 1 each Saw, Circular, 7-1/4-in 1 each Blade, Saw, Circular 1 each Level, 24-in, Aluminum 1 each Level, 72-in, Aluminum 1 each Tape Measure, 300-ft 1 each Measuring, Tape, Steel, 3/8-in x 100-ft, Closed 1 each Measuring, Tape, Non-Magnetic, Single Hook, 1-in x 25-ft 1 each Measuring, Wheel 1 each Framing Square 1 each Saw, Hand 1 each Saw, Key Hole 1 each Ratcheting Combination Wrench, 1-1/4-in 1 each Ratcheting Combination Wrench Set, Metric, 17 pieces 1 each Ratcheting Combination Wrench Set, SAE, 15 pieces 1 each Open End Wrench, 1-1/4-in 1 each Open End Wrench, 1-1/2-in 1 each Open End Wrench, 1.625-in 1 each Open End Wrench, 1-3/4-in 1 each Open End Wrench, 2-in 1 each Wrench, Adjustable, 18-in 1 each Wrench, Adjustable, 12-in 1 each Wrench, Adjustable, 6-in and 8-in 1 set of two (2) Wrench, Pipe, Adjustable, 2.5-in Capacity, 18-in Long 1 each Wrench, Bung, Nylon, for Plastic & Metal Drums 1 each Nut Driver Set, 16 pieces (Metric & SAE) 1 each Socket Set, 118 pieces (Metric & SAE) 1 each Allen Key Set, 10 pieces (SAE) 1 each Allen Key Set, 8 pieces 1 each Screw Driver Set, 15 pieces 1 each Hammer, Claw, 16-oz, Fiberglass Handle 1 each Hammer, Ball Peen 1 each Mallet, Soft Surface 1 each Mallet, Hard Surface 1 each Hammer, Sledge, 3-lb 1 each Knife, Utility, Retractable, 6-in 1 each Blade, Utility, Heavy Duty, 100-pack 1 each Broom, Head, Polypropylene, 18-in, Acme Threaded Handled 1 each Connection Handle, Broom, 60-in, Acme Threaded 1 each Broom, Dusting, Bench, 8-in x 3-in, Medium Bristle 1 each Dust Pan 1 each Floor Scraper 1 each Replacement Blades, Floor Scraper 1 each Paint Scraper, 2-1/2-in 1 each Scraper Blades, Replacement, 2-1/2-in 1 each Paint Scraper, 4-in 1 each Scraper Blades, Replacement, 4-in 1 each Ladder 1 each

C-50

Item Unit of Issue Hose, Water, 5/8-in x 100-ft 1 each Nozzle, Water Hose 1 each Grease Gun 1 each Cone, Traffic, Safety, Orange, 18-in 1 set of four (4) Gun, Caulk, Hex Rod, Parallel Frame 1 each 55-Gallon Drum with lid 1 each Sling, Drum, 55-Gallon 1 each Hand Truck, Drum, 55-Gallon 1 each Drum Handle/Bung Wrench, 55-Gallon 1 each Funnel, Drum, 55-Gallon 1 each Spiral Mixing Arm 1 each Traffic Paint, Black, 5-Gallon Bucket 1 pallet of 12 buckets Traffic Paint, White, 5-Gallon Bucket 1 pallet of 12 buckets Traffic Paint, Yellow, 5-Gallon Bucket 1 pallet of 12 buckets Glass Beads, Type 3, Airport, 50-lb Bag 1 pallet of five (5) bags Paint Roller Handle, 3-in 1 each Roller Cover, 3-in (2-pack) 1 each Paint Roller Handle, 9-in 1 each Roller Cover, 9-in (3-pack) 1 each Extension Handle, Paint Roller 1 each Brush, Paint, 2-in 1 each Brush, Paint, 4-in 1 each Brush, Paint, 6-in 1 each Bucket, Plastic, Utility, 5-Gal 1 each Bucket, Lid, Plastic, Utility, 5-Gal 1 each Paint Bucket Grid 1 each Paint Tray 1 each Paint Tray Liners 1 each Painter’s Tape, 2-in 1 each Painter’s Tape, 4-in 1 each Plastic Sheeting, 20-ft x 100-ft, 6mil, clear, roll 1 each Vinyl Tarp, 10-ft x 20-ft 1 each Caulk 1 case of 12 tubes Tyvek Suit, Large 1 each Tyvek Suit, Extra Large 1 each Respirator, Particulate, N95, 20-pack 1 each Gloves, Disposable (X-Large) (U/I 100 ea) 1 each Towels, Paper, Shop, 200 count box 1 each Shop Rags, 60-count 1 each Can, Trash, 55-Gal, Plastic 1 each Lid, Can, Trash, 55-Gal, Plastic 1 each Odorless Mineral Spirits, 1-Gallon 1 case of four (4) Dish, Soap, Dawn, 1-Gallon 1 case of four (4) Spray-on Lubricant, 16-oz Can 1 each String, Mason Line, Nylon, Fluorescent Yellow, 500-ft 1 each 20-ISO Container, Side Opening (with all Wall Cabinets 1 each installed) Wall Cabinet, 28-in x 14-in x 22-in NONE Wall Cabinet, 28-in x 22-in x 37.5-in w/five (5) drawers NONE Wall Cabinet, 28-in x 22-in x 37.5-in w/three (3) drawers NONE Wall Cabinet, 30-in x 18-in x 75-in NONE Flammable Storage Locker, 23-in x 18-in x 25-in 1 each

C-51

Item Unit of Issue Basket, wire, bottom (48-in x 40-in x 42-in) 1 each Ratchet Strap (2-in x 27-ft) w/Double J-Hooks 1 each Ratchet Strap (2-in x 12-ft) w/Double J-Hooks 1 each Chain, 3/8-in, Grade 70, 20-ft w/Grab Hooks 1 each Chain, Ratchet Chain Binder, 3/8-in x 1/2-in, 9,200-lb 1 each Lock, Combination, Government 1 each Pole Gun w/two (2) wheel carriage 1 each Hose Hanger Bracket for Pole Gun w/two (2) wheel carriage 1 each Hose, 1/4-in x 25-ft, for Pole Gun w/two (2) wheel carriage 1 each Manual Laser Guidance, Assembly 1 each Seat Assembly 1 each AL120, Line Guide Assembly 1 each Headset (Single Muff), Communication 1 each Headset (Double Muff), Communication 1 each Communication Master Control Station 1 each

C8. PACKAGING MAOS PAINT STRIPER KIT IN ISO CONTAINER

C8.1. Wall Cabinet, 28-in x 14-in x 22-in. Package the four (4) wall cabinets, 28-in x 14-in x 22-in, per drawings/inventory on page C-66.

C8.2. Wall Cabinet, 28-in x 22-in x 37.5-in w/five (5) drawers. Package the one (1) wall cabinet, 28-in x 22-in x 37.5-in with five (5) drawers, per drawings/inventory on page C-66.

C8.3. Wall Cabinet, 28-in x 22-in x 37.5-in w/three (3) drawers. Package the one (1) wall cabinet, 28-in x 22-in x 37.5-in w/three (3) drawers, per drawings/inventory on page C-66.

C8.4. Wall Cabinet, 30-in x 18-in x 75-in. Package the one (1) wall cabinet, 30-in x 18-in x 75-in, per drawings/inventory on page C-66.

C8.5. Basket, wire, bottom (48-in x 40-in x 42-in). Package the four (4) baskets, wire, bottom (48-in x 40-in x 42- in), per drawings/inventory on page C-66.

C8.6. 20-ft ISO Container, Side Opening. Package the one (1) 20-ft ISO container, side opening with the appropriate items per drawings/inventory on pages C-65 thru C-71.

C8.7. Material Safety Data Sheets. The material SDS will be secured in some kind of plastic document protector and placed inside the QuadCon or attached to the inside of one of the container doors.

C8.8. Container Inventory & Packaging Diagram. The contractor shall provide a full container inventory listing and packaging diagram. The container inventory listing and packaging diagram will be secured in some kind of plastic document protector and placed inside the QuadCon or attached to the inside of one of the container doors.

C8.9. Full MAOS Paint Striper Kit Drawing Package. The contractor shall furnish to the gov’t a full MAOS paint striper kit drawing package. This drawing package shall include a complete inventory listing with National Stock Numbers (NSNs)/manufacturer’s part numbers (if not a NSN has been created for item), packaging drawings with item details (as seen in drawings on pages C-65 thru C-71), be gov’t owned, and have the AFCEC logo on each page. If there are any approved (gov’t) changes to any item in this MAOS paint striper kit, the contractor shall provide updated revisions of the drawing package within 90 calendar days of each approved change.

C9. MAOS PAINT STRIPER KIT COMPONENTS VERIFICATION

C9.1. Classification of Inspections of MAOS paint striper kit components. The inspection requirements specified herein are classified as follows:  First article inspection.

C-52

 Conformance inspection.

C9.1.1. First Article Inspection. The purpose of this inspection shall be to determine MAOS Paint Striper Kit’s conformity with the contract. Acceptance of the First Article inspection shall not constitute a waiver by the Government of its rights under the provisions contract document or relieve the manufacturer from any requirements defined in this specification. Failure to meet inspection criteria shall constitute cause for rejection.

C9.1.2. Conformance Inspection. The conformance inspection shall be conducted on all full/partial MAOS Paint Striper Kits prior to the contractor shipping the MAOS Paint Striper Kits as stated in SOW paragraph 3.1.1.

C-53

4 3 2 1 ITEM NO. DESCRIPTION QTY. 6 1 PAINT STRIPER STAND 2 2 FRONT LEFT BRACKET 1 1 3 FRONT RIGHT BRACKET 1 4 SHIPPING PLATE MIDDLE 2 5 BACK LEFT BRACKET 1 4 6 BACK RIGHT BRACKET 1 7 FLAT WASHER 1/2", GRADE 8 24 5 1 B 8 SCREW, 1/2'-13, 5" LONG, GRADE 8 4 B 9 SPLIT LOCK WASHER, 1/2", GRADE 8 12 3 10 SCREW, 1/2"-13, 3-1/4" LONG, GRADE 8 8 11 HEX NUT, 1/2"-13, GRADE 8 12

EXPANDED METAL DECKING IS NOT SHOWN FOR CLARITY

2

A FRONT VIEW A

UNLESS OTHERWISE SPECIFIED: NAME DATE

DIMENSIONS ARE IN INCHES DRAWN LEFT VIEW TOLERANCES: FRACTIONAL 1/16 CHECKED TITLE: ANGULAR: MACH 1 BEND 2 ONE PLACE DECIMAL .03 ENG APPR. TWO PLACE DECIMAL .015 THREE PLACE DECIMAL .005 MFG APPR. FULL STAND ASSEMBLY INTERPRET GEOMETRIC Q.A. PROPRIETARY AND CONFIDENTIAL TOLERANCING PER: ASME Y14.5-2009 COMMENTS: THE INFORMATION CONTAINED IN THIS MATERIAL DRAWING IS THE SOLE PROPERTY OF SIZE DWG. NO. REV . ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF NEXT ASSY USED ON B IS PROHIBITED. APPLICATION DO NOT SCALE DRAWING SCALE: 1:16 WEIGHT: SHEET 1 OF 1 4 3 2 1 C-54 4 3 2 1 ITEM NO. QTY. DESCRIPTION LENGTH 1 1 TUBE, SQUARE 2.00 X 2.00 X 0.25 44.63 2 1 TUBE, SQUARE 2.00 X 2.00 X 0.25 44.63 3 2 TUBE, SQUARE 2.00 X 2.00 X 0.25 60 4 4 TUBE, SQUARE 2.00 X 2.00 X 0.25 23.88 D 5 8 TUBE, SQUARE 2.00 X 2.00 X 0.25 16.76 D 6 2 L 1.25 X 1.25 X 0.188 22.31 7 1 L 1.25 X 1.25 X 0.188 56 8 2 L 1.25 X 1.25 X 0.188 22.13 9 4 PLATE, 4.00 X 4.00 X 0.25, STEEL 10 1 FLATTENED EXPANDED METAL, 58.0 X 46.6 X 0.12, STEEL NOTE: ITEM 10 NOT SHOWN FOR CLARITY

3

1

6 2

7 C C 48.6

8

60.0 3

B 3/16 3/16 B 3/16 3/16

3/16 4 3/16 3/16 3/16 3/16 3/16 5 3/16 3/16 26.13±.10 3/16

3/16

9 FRONT VIEW RIGHT SIDE VIEW

UNLESS OTHERWISE SPECIFIED: NAME DATE DIMENSIONS ARE IN INCHES TOLERANCES: DRAWN FRACTIONAL 1/16 A CHECKED TITLE: A ANGULAR: MACH 1 BEND 2 ONE PLACE DECIMAL .1 ENG APPR. TWO PLACE DECIMAL .015 THREE PLACE DECIMAL .005 MFG APPR. PAINT STRIPER INTERPRET GEOMETRIC Q.A. PROPRIETARY AND CONFIDENTIAL TOLERANCING PER: COMMENTS: STAND THE INFORMATION CONTAINED IN THIS MATERIAL DRAWING IS THE SOLE PROPERTY OF SIZE DWG. NO. REV . ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF NEXT ASSY USED ON C IS PROHIBITED. APPLICATION DO NOT SCALE DRAWING SCALE: 1:12 WEIGHT: SHEET 1 OF 3 4 3 2 1 C-55 4 A 3 2 1

1.0 9

NOTE: ITEM 10 NOT SHOWN FOR CLARITY 1/8 1/8 D D 1/8

1/8 1/8 1/8 1/8 1/8

1/8 1/8 1/8

23.1 C C

1.0 20.0 20.0 SECTION A-A SCALE 1 : 8 A 4X .56 2.0

2 36.00 2X .56 2.0 3 24.00 1.00 4.37 51.25±.06 1.00 6.31 12.00

B B

FRONT VIEW RIGHT SIDE VIEW

UNLESS OTHERWISE SPECIFIED: NAME DATE DIMENSIONS ARE IN INCHES DRAWN TOLERANCES: A FRACTIONAL 1/16 CHECKED TITLE: A ANGULAR: MACH 1 BEND 2 ONE PLACE DECIMAL .1 ENG APPR. TWO PLACE DECIMAL .015 THREE PLACE DECIMAL .005 MFG APPR. PAINT STRIPER INTERPRET GEOMETRIC Q.A. PROPRIETARY AND CONFIDENTIAL TOLERANCING PER: COMMENTS: STAND THE INFORMATION CONTAINED IN THIS MATERIAL DRAWING IS THE SOLE PROPERTY OF SIZE DWG. NO. REV . ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF NEXT ASSY USED ON C IS PROHIBITED. APPLICATION DO NOT SCALE DRAWING SCALE: 1:12 WEIGHT: SHEET 2 OF 3 4 3 2 1 C-56 4 3 2 1

1/8 3/8-4 1/8 3/8-4 10

D NOTE: ITEM 10 ILLUSTRATED AS A SOLID PLATE TO SIMPLIFY DRAWING D

1/8 3/8-4

1/8 3/8-4

C C

2X .56 2.0 3

51.25±.06 4.37 1.00

1

B B

BACK VIEW LEFT SIDE VIEW

UNLESS OTHERWISE SPECIFIED: NAME DATE DIMENSIONS ARE IN INCHES DRAWN TOLERANCES: A FRACTIONAL 1/16 CHECKED TITLE: A ANGULAR: MACH 1 BEND 2 ONE PLACE DECIMAL .1 ENG APPR. TWO PLACE DECIMAL .015 THREE PLACE DECIMAL .005 MFG APPR. PAINT STRIPER INTERPRET GEOMETRIC Q.A. PROPRIETARY AND CONFIDENTIAL TOLERANCING PER: COMMENTS: STAND THE INFORMATION CONTAINED IN THIS MATERIAL DRAWING IS THE SOLE PROPERTY OF SIZE DWG. NO. REV . ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF NEXT ASSY USED ON C IS PROHIBITED. APPLICATION DO NOT SCALE DRAWING SCALE: 1:12 WEIGHT: SHEET 3 OF 3 4 3 2 1 C-57 A B MATERIAL: 1/2"PLATE-A36STEEL 4 4 BANJO PLATE .50 3 3 PROHIBITED. IS WITHOUT THEWRITTEN PERMISSIONOF REPRODUCTION INPART ORASAWHOLE .ANY DRAWING ISTHESOLEPROPERTYOF THE INFORMATIONCONTAINEDINTHIS PROPRIETARY ANDCONFIDENTIAL 0 5.75 FRONT PLATE1 NEXT ASSY APPLICATION 7.50 USED ON 2 2 TOLERANCING PER:ASMEY14.5-2009 INTERPRET GEOMETRIC MATERIAL FINISH THREE PLACEDECIMAL ONE PLACEDECIMAL TWO PLACEDECIMAL FRACTIONAL TOLERANCES: DIMENSIONS AREININCHES UNLESS OTHERWISESPECIFIED: ANGULAR: MACH DO NOTSCALEDRAWING 1/16 1 BEND .03 .005 .015 2 ENG APPR. DRAWN CHECKED Q.A. COMMENTS: MFG APPR. NAME .50

DATE 0 TITLE: SIZE SCALE: 1:2 B FRONT LEFTBRACKET DWG. NO. WEIGHT: 1 1 COMPLETE PEN BACK GOUGE SHEET 1OF C-58 REV A B 4 3 2 1

.50 MATERIAL: 1/2" PLATE - A36 STEEL

COMPLETE PEN B BACK GOUGE B

9.00

5.75 FRONT PLATE 1

A 0 A

UNLESS OTHERWISE SPECIFIED: NAME DATE

DIMENSIONS ARE IN INCHES DRAWN TOLERANCES: FRACTIONAL 1/16 0 CHECKED TITLE: ANGULAR: MACH 1 BEND 2

.50 ONE PLACE DECIMAL .03 ENG APPR. 4.25 TWO PLACE DECIMAL .015 THREE PLACE DECIMAL .005 MFG APPR. FRONT RIGHT BRACKET INTERPRET GEOMETRIC Q.A. PROPRIETARY AND CONFIDENTIAL TOLERANCING PER: ASME Y14.5-2009 COMMENTS: BANJO PLATE THE INFORMATION CONTAINED IN THIS MATERIAL DRAWING IS THE SOLE PROPERTY OF SIZE DWG. NO. REV . ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF NEXT ASSY USED ON B IS PROHIBITED. APPLICATION DO NOT SCALE DRAWING SCALE: 1:2 WEIGHT: SHEET 1 OF 1 4 3 2 1 C-59 4 3 2 1

MATERIAL: 1/2" PLATE - A36 STEEL

.50

B COMPLETE PEN B BACK GOUGE .50

BACK PLATE 2

BANJO PLATE

5.75 5.75 3/8 1-2 3/8 1-2

1.00 2.38 .50

0 0 A A

UNLESS OTHERWISE SPECIFIED: NAME DATE

BACK PLATE 1 DIMENSIONS ARE IN INCHES DRAWN TOLERANCES: FRACTIONAL 1/16 CHECKED TITLE: ANGULAR: MACH 1 BEND 2 ONE PLACE DECIMAL .03 ENG APPR. TWO PLACE DECIMAL .015 THREE PLACE DECIMAL .005 MFG APPR. BACK LEFT BRACKET INTERPRET GEOMETRIC Q.A. PROPRIETARY AND CONFIDENTIAL TOLERANCING PER: ASME Y14.5-2009 COMMENTS: THE INFORMATION CONTAINED IN THIS MATERIAL DRAWING IS THE SOLE PROPERTY OF SIZE DWG. NO. REV . ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF NEXT ASSY USED ON B IS PROHIBITED. APPLICATION DO NOT SCALE DRAWING SCALE: 1:2 WEIGHT: SHEET 1 OF 1 4 3 2 1 C-60 4 3 2 1

MATERIAL: 1/2" PLATE - A36 STEEL

COMPLETE PEN BACK PLATE 2 B BACK GOUGE B

.50

BACK PLATE 1

5.75 5.75 3/8 1-2 3/8 1-2

1.00 2.38

0 0

A .50 A

UNLESS OTHERWISE SPECIFIED: NAME DATE

DIMENSIONS ARE IN INCHES DRAWN BANJO PLATE TOLERANCES: FRACTIONAL 1/16 CHECKED TITLE: ANGULAR: MACH 1 BEND 2 ONE PLACE DECIMAL .03 ENG APPR. TWO PLACE DECIMAL .015 THREE PLACE DECIMAL .005 MFG APPR. BACK RIGHT BRACKET INTERPRET GEOMETRIC Q.A. PROPRIETARY AND CONFIDENTIAL TOLERANCING PER: ASME Y14.5-2009 COMMENTS: THE INFORMATION CONTAINED IN THIS MATERIAL DRAWING IS THE SOLE PROPERTY OF SIZE DWG. NO. REV . ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF NEXT ASSY USED ON B IS PROHIBITED. APPLICATION DO NOT SCALE DRAWING SCALE: 1:2 WEIGHT: SHEET 1 OF 1 4 3 2 1 C-61 4 3 2 1

MATERIAL: 1/2" PLATE - A36 STEEL MATERIAL: 1/2" PLATE - A36 STEEL Qty: 2 Qty: 4

.50 B .50 B

.5 X 45° .5 X 45° R.75 .55 9.00 5.75

7.85 4.50

R.38 7.15 3.20

5.75 R.22

0 0 3.75 2.80 1.50 1.25 BANJO PLATE A DXF INCLUDED A 0 UNLESS OTHERWISE SPECIFIED: NAME DATE

DIMENSIONS ARE IN INCHES DRAWN TOLERANCES: 0 FRACTIONAL 1/16 CHECKED TITLE: ANGULAR: MACH 1 BEND 2

9.25 5.25 4.10 3.40 1.38 ONE PLACE DECIMAL .03 ENG APPR. TWO PLACE DECIMAL .015 THREE PLACE DECIMAL .005 MFG APPR. BRACKET PLATES INTERPRET GEOMETRIC Q.A. BACK PLATE 1 PROPRIETARY AND CONFIDENTIAL TOLERANCING PER: ASME Y14.5-2009 COMMENTS: THE INFORMATION CONTAINED IN THIS MATERIAL DXF INCLUDED DRAWING IS THE SOLE PROPERTY OF SIZE DWG. NO. REV . ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF NEXT ASSY USED ON B IS PROHIBITED. APPLICATION DO NOT SCALE DRAWING SCALE: 1:2 WEIGHT: SHEET 1 OF 2 4 3 2 1 C-62 4 3 2 1

MATERIAL: 1/2" PLATE - A36 STEEL Qty: 2 MATERIAL: 1/2" PLATE - A36 STEEL Qty: 2 B .50 B

.50 .55

9.00

7.85

7.15 1.00

9.25

BACK PLATE 2

1.25 A A

0 UNLESS OTHERWISE SPECIFIED: NAME DATE DIMENSIONS ARE IN INCHES TOLERANCES: DRAWN FRACTIONAL 1/16 CHECKED TITLE: 0 ANGULAR: MACH 1 BEND 2 ONE PLACE DECIMAL .03 ENG APPR.

7.50 4.38 2.35 1.65 TWO PLACE DECIMAL .015 THREE PLACE DECIMAL .005 MFG APPR. BRACKET PLATES INTERPRET GEOMETRIC Q.A. PROPRIETARY AND CONFIDENTIAL TOLERANCING PER: ASME Y14.5-2009 COMMENTS: FRONT PLATE 1 THE INFORMATION CONTAINED IN THIS MATERIAL DRAWING IS THE SOLE PROPERTY OF SIZE DWG. NO. REV DXF INCLUDED . ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF NEXT ASSY USED ON B IS PROHIBITED. APPLICATION DO NOT SCALE DRAWING SCALE: 1:2 WEIGHT: SHEET 2 OF 2 4 3 2 1 C-63 4 3 2 1

ITEM 2 QUANTITY: 2 .25 4.00 6.25 7.50

B 9.00 B

7.85

7.15

4.00

.55

1.25

0 0 1.02 1.73 9.77

A 10.48 11.50 A DXF INCLUDED UNLESS OTHERWISE SPECIFIED: NAME DATE

DIMENSIONS ARE IN INCHES DRAWN TOLERANCES: FRACTIONAL 1/16 CHECKED TITLE: ANGULAR: MACH 1 BEND 2 ONE PLACE DECIMAL .03 ENG APPR. TWO PLACE DECIMAL .015 THREE PLACE DECIMAL .005 MFG APPR. SHIPPING PLATE MIDDLE INTERPRET GEOMETRIC Q.A. PROPRIETARY AND CONFIDENTIAL TOLERANCING PER: ASME Y14.5-2009 COMMENTS: THE INFORMATION CONTAINED IN THIS MATERIAL DRAWING IS THE SOLE PROPERTY OF SIZE DWG. NO. REV . ANY REPRODUCTION IN PART OR AS A WHOLE FINISH WITHOUT THE WRITTEN PERMISSION OF NEXT ASSY USED ON B IS PROHIBITED. APPLICATION DO NOT SCALE DRAWING SCALE: 1:2 WEIGHT: SHEET 1 OF 1 4 3 2 1 C-64 4 3 2 1 PARTS LIST

ITEM PART NO. QTY DESCRIPTION MATERIAL

1 1 STRIPER STAND 2 1 STRIPER MACHINE AL.120 3 1 BULK CONTAINER 1 4 1 BULK CONTAINER 2 D D 5 1 BULK CONTAINER 3 6 6 1 BULK CONTAINER 4 7 2 LADDERS AND LEVELS 8 1 HAZMAT BOX 9 1 BEAD TANK, PAINT STRIPER 10 1 FLAMMABLE BOX 11 1 CABINET 12 8 55 GALLON DRUM 13 1 GENERATOR 14 1 PAINT SPRAYER AIRLESS 15 1 DOLLY 16 1 CAN, TRASH 55 GALLON

6 9 7 12 16 15 8 10 11

C C

1

2

CONTAINER 1 5 ISOMETRIC VIEW (TOP AND SIDE VIEW REMOVED FOR CLARITY) 4 Scale: NTS

3

5 1 2 12 13 14

B CONTAINER 1 B PLAN VIEW (TOP AND SIDE VIEW REMOVED FOR CLARITY) Paint striper chair packed Scale: NTS in cardboard box

2

CONTRACTOR VIZOCOM 17/03/2020 CONTRACT NUMBER FA805119PA033 TITLE A A PAINT STRIPER KITS

1 CONTAINER 1 SIZE DWG NO REV ELEVATION VIEW (TOP AND SIDE VIEW REMOVED FOR CLARITY) C 01 A Scale: NTS SCALE NTS SHEET 1 OF 7

4 3 2 1 C-65 LOAD CABINET 4 Add gallon jugs of dish soap (6), gallon jugs of mineral spirits (10) and synthetic lubricant spray cans (20) to the cabinet bottom. Add paint roller pans (20), paint roller pan stripers (75), paint bucket roller grids (3), primary intercom system [headsets with boom mic (2), master station (1), remote station (1), power cables (2)], primary MST-14 Skip Timer system (1), primary line guidance laser and guide assembly (1), primary XHD RAC Tip Guards (3), primary bead gun tips (3) and pickup truck installation tie down assembly [brackets (2), Turnbuckles (2)] to the cabinet shelf.

4 3 2 1 AFCEC AIRFIELD LINER UTC LOAD SEQUENCE

LOAD CABINET 3 D BULK CONTAINER 1 Painter's Tape 2-in 60 yards, Painter's Tape 4-in 60 yards, D Funnel, Traffic Paint White (5 Gal), Tyvek Suit (L), Tyvek Suit (XL), Respirator Particulate N95, Gloves Latex - (box of 100) Paint Bucket Grid, Paint Tray, LOAD CABINET 1 Paint Tray Liners Broom, Street , Broom, Hand, Paint Scraper 2-1/2-in, Paint Scraper 4-in, Odorless Mineral Spirits (1 gal. ea.) LOAD CABINET 4 Vinyl Tarp, Paper Towels, Dish Soap, Dawn (1 gal)

LOAD CABINET 2 LOAD CABINET 5 Saw Reciprocating, 12-AMP with Case, Tape, Power-stroke Paint Hose, Measuring Tape 300-ft, Tape, Measuring 100-ft, Cord Extension 50-ft, Jerrican Diesel Measuring Wheel, Saw Hand, Saw Key Hole, 5-Gallon, Jerrican Gas (Mogas) 5-Gallon, Sling Drum 55-gallon, Mason (String) Line Fuel Spout Jerrican, Saw Jig, Drill Electric, Saw Circular 7-1/4-in, Water Hose 100-ft, Grease Gun, Caulking Gun, Drum DRAWER 1 Handle/Bung Wrench, Paint Roller Blade Reciprocating Saw, Blade Jig Saw (15 pcs), Handle 3-inch, Roller Cover 3-in BULK CONTAINER 2 Blades Saw Circular 7-1/4-in, Allen Key Set, (packs of 2), Paint Roller Handle 9-inch, Dustpan with handle, Cone Traffic Allen Key Set, Screw Driver Set 15 pcs, Roller Cover pack of 3 9-in, Safety Orange 18-inch, Traffic Paint Replacement Blades Floor Scraper, Caulk (12 packs) Yellow (5 Gal) buckets Scraper Blades, Replacement 2-1/2-in, Scraper Blades, Replacement, 4-in (10 per package) C DRAWER 6 C DRAWER 2 Framing Square, Hammer Claw, Spade Drill Bit Set, Drill & Bit Set, Hammer Ball Peen, Mallet, Soft Hole Saw Kit (7 pcs), Tape, Measuring 25-ft, Surface, Mallet Hard Surface, Nut Driver Set, Utility Knife, Blades Utility Sledge Hammer Knife (100 pcs) Drawer 1 Drawer 6 DRAWER 3 Wrench Adjustable 18-in, Wrench Adjustable Drawer 2 12-in, Wrench Pipe, Wrench Bung, Socket Set Drawer 3 DRAWER 4 Ratcheting Combination Wrench 1 1/4 inch, Drawer 7 Drawer 8 Ratcheting Combination Wrench Set, Drawer 4 BULK CONTAINER 3 Metric, 17 pieces, Ratcheting Traffic Paint Black (5 Gal), Combination Wrench Set SAE 15 pieces, Drawer 5 Plastic Sheeting Open End Wrench 1240 1.25 inch, Open End Wrench 1248 1.5 inch, Open End Wrench 1252 1 5/8 inch, Open End Wrench 1 3/4 1256, Open End Wrench 1264 2 in, Wrench Adjustable Set 6-in and 8-in, B B Nozzle, Water Hose DRAWER 8 Spiral Mixing Arm, Brush Paint 6-in, DRAWER 5 5 gal grey trash can 25 ft hose, AL120 Bead Hose Assembly, Paint Hose 1/2 inch diam 96-in, Paint Hose 1/2 inch diam 132-in, WYE Strainer Screen, Magnetic Sensors, V-Belt, Hand Gun with acessories DRAWER 7 (for paint only), part LL5319, Brush Paint 2-in, Brush Paint 4-in rac 5 switch tip attached. BULK CONTAINER 4 Cone Traffic Safety Orange 18-inch, Glass Beads

CONTRACTOR VIZOCOM 17/03/2020 CONTRACT NUMBER FA805119PA033 TITLE A AFCEC AIRFIELD LINER UTC A LOAD SEQUENCE

SIZE DWG NO REV C 01 A SCALE NTS SHEET 2 OF 7

4 3 2 1 C-66 4 3 2 1

D D

C C

B B

CONTRACTOR VIZOCOM 17/03/2020 CONTRACT NUMBER FA805119PA033 TITLE A A ITEMS LIST

SIZE DWG NO REV C 01 A SCALE NTS SHEET 3 OF 7

4 3 2 1 C-67 4 3 2 1

D D

EQ. EQ.

22.00 22.00

C C CABINET N.ž 1 ISOMETRIC VIEW Scale: NTS

28.00 14.00

CABINET N.ž 1 CABINET N.ž 1 ELEVATION VIEW SIDE VIEW Scale: NTS Scale: NTS

B B 14.00

28.00

CABINET N.ž 1 PLAN VIEW Scale: NTS QUANTITY = 4 CONTRACTOR VIZOCOM 17/03/2020 CONTRACT NUMBER FA805119PA033 TITLE A A CABINET N.ž 1

SIZE DWG NO REV C 01 A SCALE NTS SHEET 4 OF 7

4 3 2 1 C-68 4 3 2 1

D D

Drawer 1

Drawer 2

Drawer 3

37.50 37.50

Drawer 4

C Drawer 5 C

CABINET N.ž 2 28.00 22.00 ISOMETRIC VIEW Scale: NTS

CABINET N.ž 2 CABINET N.ž 2 ELEVATION VIEW SIDE VIEW Scale: NTS Scale: NTS

28.00

B B

22.00

QUANTITY = 1 CONTRACTOR VIZOCOM 17/03/2020 CABINET N.ž 2 CONTRACT NUMBER PLAN VIEW FA805119PA033 Scale: NTS TITLE A A CABINET N.ž 2

SIZE DWG NO REV C 01 A SCALE NTS SHEET 5 OF 7

4 3 2 1 C-69 4 3 2 1

D D

Drawer 6

37.50 37.50

EQ. EQ. Drawer 7 Drawer 8

C C

28.00 22.00 CABINET N.ž 3 ISOMETRIC VIEW Scale: NTS CABINET N.ž 3 CABINET N.ž 3 ELEVATION VIEW SIDE VIEW Scale: NTS Scale: NTS

28.00

B B

22.00

QUANTITY = 1 CONTRACTOR VIZOCOM 17/03/2020 CABINET N.ž 3 CONTRACT NUMBER PLAN VIEW FA805119PA033 TITLE Scale: NTS A A CABINET N.ž 3

SIZE DWG NO REV C 01 A SCALE NTS SHEET 6 OF 7

4 3 2 1 C-70 4 3 2 1

D D

EQ. EQ.

75.00 75.00

C C

CABINET N.ž 4 ISOMETRIC VIEW 30.00 18.00 Scale: NTS B B CABINET N.ž 4 CABINET N.ž 4 ELEVATION VIEW SIDE VIEW Scale: NTS Scale: NTS

30.00

18.00 QUANTITY = 1 CONTRACTOR VIZOCOM 17/03/2020 CONTRACT NUMBER FA805119PA033 TITLE A A CABINET N.ž 4 PLAN VIEW CABINET N.ž 4 Scale: NTS

SIZE DWG NO REV C 01 A SCALE NTS SHEET 7 OF 7

4 3 2 1 C-71