INSTRUCTIONS FOR 1830-185 TCP/IP MANUAL MODE to RS-232 CONVERTER KIT

Connection via General Information Connection via LAN

System IP Address Use these instructions when using the TCP/IP adapter, part number 1830-185. This device is a manual System IP Address

Connection Option Network setup (no subscription required). For Plug and Play setup (no manual setup required) use TCP/IP adapter Connection Option Network DKS Cellular part number 1830-186 (DKS Data over IP or DKS VoIP Voice + Data subscription service required). DKS Cellular Model Number DKS Data over IP Model Number DKS Data over IP Area Codes DKS VoIP Voice + Data Area Codes DKS VoIP Voice + Data IM Server Modem You can use the 1830-185 Converter Kit with the following DKS Systems: IM Server Modem Dial First, then Modem to Modem Dial First, then Modem to Modem Network 1830 Series Telephone Entry and Access Control Systems (1833, 1834, 1835, 1837, 1838). Network RS 232 RS 232 Refer to these instruction manuals for additional information: Network selected in Remote P/N 1835-065 Telephone Entry Systems Installation Manual Account Manager Software. P/N 1838-065 Access Controller Installation Manual Network selected in Remote P/N 1835-066 Remote Account Manager Software User Manual System requires turning on Port Forwarding in Account Manager Software. default gateway (). Network LAN Interface Connect Converter to 1830 Series Circuit Board RS-232 Terminals Device System requires either a Static IP address or a DDNS Host service programmed into the Router Internet or Plug & Play 1830-186 (see general Information section). Note: System requires Firewalls to allow RS-232 wire runs are limited to 500 Router Ethernet feet maximum. If greater distance Modem communication from programming PC outside the 10M/100M Network Pwr LAN N.I.D. 1 2 3 4 network. is needed, use RS232 to RS422 Interface Device Network Extender Kit, P/N 1830-190 (4000 DC 5-18V

These task will require work to be performed by Reload Defaults Feet maximum distance). Internet IT personnel responsible for the network. DoorKing technicians cannot perform this work.

BOARD DB - 9 DB - 25 FUNCTION TERMINALS PINS PINS Modem Router Ethernet wire runs Network LAN 1 3 2 Transmit Data Interface N.I.D. 1 2 3 4 limited to 330 Ft. Device 2 2 3 Receive Data Maximum.

3 7 4 Request to Send

Ethernet wire runs To Ethernet & 485 RS-232 4 8 5 Clear to Send limited to 330 Ft. 5 5 7 Signal Ground - Shell Maximum. 6 Not Used Ethernet RS-232 10M/100M A(+) B(-) Ethernet Pwr 10M/100M RS485 Pwr

Network Shield Network DC 5-18V Reload Reload Defaults DC 5-18V + Red Black Reload Defaults Green 3 2 5 1

9 6 8 7 RS-232 Cable Brown White P/N 1818-040 RS-232 & 485 To Ethernet 485 & RS-232 (6 Ft. Cable) 485 To Ethernet & RS-232 RED 1 RS232 wire runs RS-232 A(+) B(-) BLACK 2 RS-232 wire terminal RS-232 A(+) B(-) RS485 limited to 500 Ft. WHITE 3 on telephone entry / RS485 Maximum. See BROWN note above. 4 access control system GREEN 5 SHIELD circuit board 6

P/N 1830-181 Rev G 7-20 Use these programming instructions only if the factory defaults in the converter need to be changed

A Windows (Computer) Settings B Connect 1830-185 for Programming C Accessing the 1830-185 Menus D Changing 1830-185 Settings

The following defaults in the CONVERTER Local Area Connection Properties ? 1. Unplug the network cable from your PC. 1. Open any browser and type in the address of the Port 0 Settings are factory set. If they are satisfactory to CONVERTER: http://192.168.1.40 General Advanced The current settings for Port 0 may be changed using the form below. your system, there is no need to change 2. Using the network cable supplied with the 1830-185 kit, them. Connect using: plug one end into your PC and the other into the The user Log In window for the CONVERTER will appear. Intel(R) 82566DM Gigabit Network C Current Status Parameter Configure... CONVERTER. Mozilla Firefox IP Address: 192.168.1.40 Baud Rate: 19200 bps(600 ~ 1M) This connection uses the following items: File Edit View History Bookmarks Tools Help Local IP Config Gateway: 192.168.1.1 3. Power the CONVERTER with the supplied power supply. Data Size: 8 bit Client for Microsoft Networks Port: 1040 TTL1 Parity: None File and Printer Sharing for Microsoft Networks http://192.168.1.40 Baud: 19200 4. When completed, don’t forget to plug the network cable back QoS Packet Scheduler Stop Bits: 1 bit into the PC and the 1830-185 cable back into the router. TTL2 Internet Protocol (TCP/IP) Flow Mode: RTS/CTS If these defaults are not Please login: 1 Web to Serial UART packet Time: 0 (0 ~ 255)ms satisfactory, navigate to Local Install Uninstall Properties User name: admin UART packet length: 0 (0 ~ 1460)chars Area Connections in Windows. Description Misc Config Transmission Control Protocol/Internet Protocol. The default Sync Baudrete (RF2217 similar): Pass word: * * * * * (Start – Control Panel – Network wide area network protocol that provides communication Enable Uart Heartbeat Packet: Connections – Properties) across diverse interconnected networks. Login Reset Reboot Socket A Parameters Show icon in notification area when connected Router Modem 2. Enter the User name and pass word: Work Mode: TCP Server None Highlight Internet Protocal (TCP/IP) Notify me when this connection has limited or no connectivity N.I.D. 1 2 3 4 User name: admin TCP Server MAX Sockets: 8 Up to MAX KICK Then click Properties to show the Internet Password: admin Local Port Number: 1040 (1 ~ 65535) Protocol (TCP/IP) Properties Window. PRINT: OK Cancel The parameter window will appear. Modbus TCP Poll: Poll Timeout: 200 (0 ~ 9999) ms Enable Net Heartbeat Packet: Current Status Parameter Registry Type: None Location Connect With Internet protocol (TCP/IP) Properties ? Module Name: USR-TCP232-ED2 Before proceeding, write down the Local IP Config Firmware Revision: 3017 Socket B Parameters numbers (or take a screen print) in this General 2 1 Current IP Address: 192.168.0.40 Work Mode: window. You are only going to change the TTL1 NONE You can get IP settings assigned automatically if your network supports Preferred DNS Server: 8.8.4.4 IP Address and you will need to put the this capability. Otherwise, you need to ask your network administrator for the appropriate IP settings. TTL2 Standby DNS Server: 0.0.0.0 Save Cancel same IP Address number back when MAC Address: 9c-a5-25-a8-sf-13 Obtain IP address automatically Notes: programming of the CONVERTER is Web to Serial Run Time: 0day: 2hour: 47min Use the following IP address: Baud Rate can only be set to 9600 or 19200. These are the only two speeds that 1830 Series boards will run at. complete. Ethernet wire TX Count(ETH): 0/0/0 bytes Leave all other settings as shown when the converter is used in the Server Mode. IP address: 10 . 43 . 76 . 171 Misc Config 3 runs limited to RX Count(ETH): 0/0/0 bytes Subnet mask: 255 . 255 . 255 . 0 Ex: write down the numbers: 330 Ft. Reboot Conn Status(ETH)A: LISTEN/LISTEN/LISTEN 2 (these numbers will not be the same in your Default gateway: 10 . 43 . 76 . 211 Maximum. Conn Status(ETH)B: IDLE/IDLE/IDLE computer) IP Address Selection Obtain DNS address automatically IP Address: 10.43.76.171 Use the following DNS server address: Current Status Parameter Subnet mask: 255.255.255.0 Preferred DNS server: 10 . 43 . 76 . 198 You can access settings of the CONVERTER D by using the Local IP Config IP type: Static IP Alternate DNS server: 10 . 43 . 76 . 158 Default gateway: 10.43.76.211 menu at the left in the Status and Configuration screen. Only DNS type: Auto

selections 1, 2 and 6 apply to this module. TTL1 Static IP: 192 168 0 10 Advanced Preferred DNS server: 10.43.76.198 Submask: 255 255 255 0 Alternate DNS server: 10.43.76.158 It is highly recommended that you DO NOT change the password TTL2 OK Cancel Gateway: 192 168 0 1 Ethernet on the authentication screen. DoorKing will not be able to assist 10M/100M Web to Serial DNS Server 8 8 4 4 Pwr you if you don’t know your ID or password. This system status

Network window is informational and there’s no need to change anything Misc Config Internet protocol (TCP/IP) Properties ? DC 5-18V

Reload Defaults Save Cancel here. General Reboot

You can get IP settings assigned automatically if your network supports this capability. Otherwise, you need to ask your network administrator Reset: for the appropriate IP settings. 1. Remove power from module.

Obtain IP address automatically 2. Press the Reload button and apply power. Notes: 3 Change IP Address to: Use the following IP address: 3. Hold the reload button for 3 seconds, then release. These are the default settings and should be left alone. If the static IP address is changed, the module will lose communication with the PC. You will need to 192.168.1.1 IP address: 192 . 168 . 1 . 1 Module is now reset. TCP IP address will be 192.168.1.40. User log into the module at the new IP address using the browser. Subnet mask: 255 . 255 . 255 . 0 name and password will be admin. All other settings will need to (This will allow your PC to connect to the Default gateway: 192 . 168 . 1 . 40 CONVERTER so that you can change its be configured. Obtain DNS address automatically settings.) 485 To Ethernet & RS-232 Use the following DNS server address:

Preferred DNS server: 10 . 43 . 76 . 198 IMPORTANT! When you are finished Alternate DNS server: 10 . 43 . 76 . 158 RS-232 IMPORTANT! When you are finished configuring the CONVERTER, you must set the Internet Protocol (TCP/IP) Properties screen on your PC configuring the CONVERTER, you must set the A(+) B(-) RS485 back to its original settings in order to get access back to your network. IP Address back to the original settings in order Advanced to get access back to your network. Follow the instructions A 1 to get to the Internet Protocol (TCP/IP) Properties screen and then put your old settings back. A 2 OK Cancel Don’t forget to plug the netowrk cable back into the PC B 1 and the CONVERTER cable back into the router. B 2