MECHANICAL FLOOR PLAN REQUIRED in ORDER to CONNECT SENSORS to the Job No

MECHANICAL GENERAL NOTES: MECHANICAL PLAN NOTES: 1. DO NOT ROUTE ANY DUCTWORK OR PIPING ABOVE ELECTRICAL PANELS. 1 TYPE I GREASE HOOD EXHAUST DUCTWORK SHALL BE MINIMUM 16 GAUGE BLACK IRON WITH LIQUID TIGHT 2. COORDINATE WITH GENERAL CONTRACTOR FOR WELDS. INSTALL ACCESS PANELS FOR CLEANING AS PROVISION OF 1" UNDERCUT OR SPACING BELOW REQUIRED BY NFPA 96 AND LOCAL CODES. PROVIDE A G R O U P DOORS AT JANITOR FOR GENERAL VENTILATION PATH UL APPROVED GREASE DUCT WRAP SYSTEM. CLEARLY OF ROOM EXHAUST SYSTEMS. LABEL ACCESS PANELS AFTER GREASE DUCT WRAP SYSTEM IS INSTALLED FOR FUTURE CLEANINGS. AT CONTRACTORS OPTION, THE DURASYSTEM KEX 830 North Blvd. PREFABRICATED RECTANGULAR GREASE DUCT SYSTEM, AS APPROVED BY LOCAL CODES, MAY BE Oak Park, PROVIDED AS ALTERNATE TO STANDARD WELDED Illinois GREASE DUCT WITH FIRE WRAP PER SPECIFICATIONS. 60301 2 PROVIDE TRANSITION TO SIZE SHOWN ON PLAN. TRANSITION GREASE DUCTWORK AS REQUIRED AT HOOD AND FAN CONNECTIONS. PROVIDE SMOOTH 708-445-8400 TRANSITION PER SMACNA AT FAN INLET. PROVIDE ariainc.com 45%%D MAX RADIUSED OFFSETS AS REQUIRED TO COORDINATE WITH STRUCTURE. 90%%D ELBOW MAY BE ARIA GROUP ARCHITECTS, INC. PROVIDED ONLY IF NOTED ON PLAN. NO TURNING VANES ALLOWED IN GREASE DUCTWORK. 3 PROVIDE CLEANOUTS PER CODE REQUIREMENTS AND AS REQUIRED TO FACILITATE CLEANING. COORDINATE WITH GENERAL CONTRACTOR TO AVOID BLOCKING ACCESS POINTS. CLEARLY LABEL ACCESS PANELS FOR .2A FUTURE MAINTENANCE. 4 INSTALL TEMPERATURE SENSORS FURNISHED WITH KITCHEN EXHAUST HOODS ON WALL. 34 COAT ROOM 5 ROUTE STAINLESS STEEL EXHAUST DUCT FROM DISHWASHER PANT-LEG UP TO EXHAUST FAN ON ROOF. 18"x8" (TYP 2) 18"x8" FAX SLOPE EXHAUST DUCT 1/4" PER FOOT TOWARD 102 WSR WSR 18"x14" DISHWASHER. MANUFACTURER TO PROVIDE STAINLESS 400 CFM WRG 400 CFM STEEL VOLUME DAMPER IN EACH PANT LEG. 1950001061 GRAB N WIN 6 PROVIDE NECESSARY TRANSITION FROM PANT-LEG LENEXA, KS 66214 A BASEBALL DISPLAY 12"x18" PACMAN SPACE PRO (2) PIXEL (2) GOLD (2) RING EXHAUST DUCTWORK TO EQUIPMENT CONNECTION. FLEX DINING 10"Ø INVADERS CONNECT 4 (2) DOWN (2) MILK 913.742.5000 913.742.5001 10"x10" EXTREME FISHING 117 BALANCE HOOD CONNECTIONS AS FOLLOWS: 200 CFM BIG ONE CHASE TOSS THE CLOWN JUG TOSS LANE LENEXA DRIVE,8345 SUITE 300 CSD CRG1 CRANE (2) SKEEBALL LETS BOUNCEMASTER TO DISHWASHER ENTRANCE END AND 400 CFM TO TEL 108 WWW.HENDERSONENGINEERS.COM 400 CFM MOUNT BOTTOM OF 8"Ø 10"Ø DUCT DISHWASHER EXIT END. 10"Ø CSD1 CSD 6"Ø AT 14' -11" AFF. 10"x6" DROP DUCT DOWN 7 CONNECT TO FULL-SIZE SUPPLY / RETURN AIR CSD 250 CFM 18"x10" 400 CFM CSD1 WSR TO NEW BOTTOM DUCTWORK STUBBED IN BY LANDLORD. IF REQUIRED TO 375 CFM WSR 75 CFM OF DUCT HEIGHT. 24"x10" OBTAIN MOUNTING HEIGHT, CUT LANDLORD PROVIDED 200 CFM 20 575 CFM 10"Ø 10"Ø WRG DUCT STUB TO INSTALL FLEXIBLE DUCT CONNECTOR AT BOTTOM OF DECK. CSD 18"x14" 8"Ø CSD MOUNT BOTTOM TECH ROOM 375 CFM ARCADE CSD1 8 DROP FULL SIZE RETURN AIR DUCT DOWN AND TAP

375 CFM TURN DOWN FAR WHITEHALL, 18052 PA OF DUCT AT (TYP 2) ENOUGH TO 125 250 CFM DUCT INTO TOP OF PLENUM. REFER TO PLAN FOR 18' -5" AFF. 24"x22" 127 10"x6" PREVENT DIRECT LINE PLENUM SIZE. MOUNT RETURN AIR PLENUM TIGHT TO RECEPTION WSR CRAZY TOWER WRG BOTTOM OF STRUCTURE. PROVIDE 1/4" GALVANIZED STAR TREK WILLY UP TO RTU -12 7 OF SIGHT WONKA TOUCH FX CONSTRUCTION HARDWARE CLOTH SCREEN OVER 10"Ø 10"Ø 10"Ø 6 103 200 CFM 18"x12" INTO ARCADE 8"x6" STORAGE OPEN END OF RETURN DUCT UNLESS WHERE NOTED TO CSD CSD CSD M2.1 18"x14" (TYP3) (4) MOTO WSR 22"x22" PROVIDE A WRG GRILLE OR DUCTED TO A CRG GRILLE. 34"x14" 10"x6" 400 CFM 400 CFM 400 CFM GP (4) CRUSIN PROVIDE DUCT LINER IN BOOT. RETURN AIR DUCT 22"x22" MIN 4'-0" 20 116 CRG HS 24"x12" (TYP) USA WRG 150 CFM CRG MOUNT BOTTOM OF DUCT WSR SHALL BE MINIMUM 4’ HORIZONTAL EXTENSION. 48"x22" 26"x16" 5 AT 17' -0" AFF. 8 1000 CFM 9 FULL SIZED LINED SUPPLY DUCT DOWN AND CONNECT FULL TILT RAMPAGE MOUNT BOTTOM OF DUCT UP TO RTU -2 7 M2.1 (TYP 8) TO A LINED OCTAGON SHAPED DROP BOX. DUCTWORK RTU-1 HS 8 10 11 DB MOUNT BOTTOM OF AT 16' -10" AFF. CO2 TS MOUNT BOTTOM OF SHALL HAVE A PAINT GRIP PRIMER FINISH TO RECEIVE TS CO2 (TYP) (4) MARIO (4) DAYTONA DUCT AT 18' -5" AFF. DUCT AT 18' -7 AFF. KART PAINT OF COLOR AS SELECTED BY ARCHITECT. B TS RTU-2 10 11 9 TS RTU-12 10 11 12"x12" CONTACT GEORGE LASHER AT 800-786-0402 FOR CYCLONE CYCLONE RTU-9 PRICING AND LEAD TIMES (5 - 6 WEEKS ESTIMATED). 10 11 38"x14" REFER TO GRILLE, REGISTER, AND DIFFUSER SCHEDULE 18"x20" 10"Ø 22"x22" FOR MORE INFORMATION. MOUNT BOTOM OF 7 UP TO RTU -9 CSD CRG 10"Ø DROP BOX AT 17' -0" AFF. 325 CFM 10 MOUNT TEMPERATURE/CO2 SENSOR 96”AFF ON CSD COLUMN/WALL FOR ALL PUBLIC AREAS EXCEPT ARCADE 10"Ø 10"Ø 8"Ø 400 CFM (2)SPINNER AREA. IN ARCADE, MOUNT SENSOR AT 108”AFF. IN BOH CSD CSD CSD FRENZY GEAR IT 10"Ø AREAS, MOUNT SENSOR AT 48” AFF.

18"x8" 12"x12" 18"x8" 18"x8" (2) UP (2) 400 CFM 200 CFM 30"x12" CSD 11 TEMPERATURE SENSORS/HUMIDITY SENSORS/C02 WSR WSR WSR 400 CFM JURASSIC BASKETBALL WIN PARK PRO (2) (TYP 2) 325 CFM SENSORS/THERMOSTATS SHALL BE LABELED TO MATCH 400 CFM 400 CFM 400 CFM WALKING TREASURE24"x22" DEAD QUEST 115 THE UNIT TAG AND CORRESPOND TO THE ELECTRICAL WRG 7 LEGEND IN THE ELECTRICAL PANELBOARD SERVING THE 18"x14" UP TO RTU -11 EQUIPMENT. THE UNIT ZONE SERVED (I.E. ARCADE, WIN, MOUNT BOTTOM OF DUCT (TYP 2) 18"x8" 18"x8" KITCHEN, ETC) SHALL ALSO BE LABELED ON THE AT 18' -10" AFF. 22"x22" WSR WSR 18"x8" 24"x12" PROGRAMMABLE T-STATS IN OFFICE. WSR CRG

400 CFM 400 CFM WSR MIN 4'-0" MOUNT BOTTOM OF 1000 CFM (2) WHACK A 10"Ø 12 PROVIDE UNIT THERMOSTATS IN GM OFFICE LOCATED 400 CFM MAIN BAR 8"Ø CENTIPEDE DUCT AT 18' -7 AFF. (TYP 8) CLOWN CSD BEHIND DOOR. PROVIDE CONTROL WIRING AS D&B SPORTS DINING 10"Ø CSD 10"Ø 110 8 48"x14" 8 325 CFM REQUIRED FOR SENSOR OPERATION. MOUNT T-STATS CSD 200 CFM 48"x16" (4) ATV SLAM CSD 48"x22" CONTEST OF PER TYPICAL OFFICE THERMOSTAT ELEVATION ON 112 ZOMBIE DB 400 CFM 400 CFM HS CHAMPIONS MECHANICAL DETAIL SHEET. COORDINATE WITH OTHER HS SNATCHER TAILGATE INJUSTICE OFFICE EQUIPMENT. LEAGUE C 18"x8" TOSS MOUNT BOTTOM OF CO2 TS 9 TS 13 CONNECT 4" PVC EXHAUST FLUE/AIR INTAKE TO WSR RTU-11 RIODROP 2016 BOX AT 17' -(2)0" AFFTON OF RTU-3 TICKETS FAMILY GUY LANDLORD PROVIDED CONCENTRIC VENT. INSTALL PER UP TO RTU -3 30"x14" (4) XGAME WILLY CRASH MOUNT BOTTOM OF 400 CFM 11 10 MANUFACTURER'S INSTRUCTIONS. COORDINATE WITH 11 10 7 UP TO RTU -1 22"x14" 38"x14" DUCT AT 17' -6" AFF. MAIN BAR DINING SNOW PLUMBING CONTRACTOR. BOARD 122 VR 14 PROVIDE TRANSFER AIR DUCTWORK FOR EXHAUST FAN 48"x24" 40"x16" 10"Ø 10"Ø MAKE-UP AIR. CONNECT TO RETURN GRILLE(S) AND WRG ROUTE TO ELECTRICAL ROOM. TERMINATE IN HS CSD CSD HOD ELECTRICAL ROOM WITH 1/4" GALVANIZED 400 CFM 400 CFM HALO 2PLY SCARLET CONSTRUCTION HARDWARE CLOTH SCREEN. 48"x24" 10"Ø DAWN 18"x14" 18"x14"

K 18"x8" 18"x8" CSD CROSSY ROAD K 15 PROVIDE ELECTRICAL ROOM EXHAUST DUCT DOWN

C 18"x8" C DREAM

O MOUNT BOTTOM OF O TYPHOON FROM EXHAUST FAN AND STUB INTO ELECTRICAL

L L RAIDER

WSR WSR WSR 400 CFM

E E BLACK

H DUCT AT 16' -6" AFF. H DESPICABLE ROOM. TERMINATE IN ELECTRICAL ROOM WITH 1/4"

400 CFM 400 CFM 400 CFM HOLE

P P ME (TYP 2) GALVANIZED CONSTRUCTION HARDWARE CLOTH

P P 24"x22" 22"x14" 10"Ø SCREEN. 10"Ø WRG CSD WORLD CUP CONNECT 4 16 MOUNT UNIT HEATER WITH BOTTOM OF UNIT AT 12” AFF

CSD E (TYP 2) MOUNT BOTTOM OF 36"x16" 36"x16" E 7 HOOPS E UP TO RTU -10 18"x8" 18"x8" 10"Ø SOCCER MEGA E PER MANUFACTURER'S RECOMMENDATIONS.

Z 400 CFM Z

T 22"x22" 400 CFM DUCT AT 19' -4" AFF. T

WRG WRG STACKER H WSR WSR CSD H

A A GUITAR HERO 17 INSTALL OWNER FURNISHED ANALOX AX60+ CARBON

Y CRG Y 24"x12" 400 CFM 400 CFM 400 CFM 11 DIOXIDE KIT WITH CENTRAL DISPLAY, REMOTE CARBON MOUNT BOTTOM OF WSR DUCT AT 19' -4" AFF. MIN 4'-0" M2.1 DIOXIDE SENSOR, AND LOCAL AUDIBLE/VISUAL ALARM. UP TO RH -1 1000 CFM 7 QUAD AIR CARBON DIOXIDE KIT WITH RELAY SHALL BE

N UP TO KEF -6 5 6 UP TO RH -2 MOUNT BOTTOM OF (TYP 8) (TYP)

B E 8 INTERLOCKED WITH THE BUILDING FIRE ALARM SYSTEM. 48"x22" M2.1 36"x16" 36"x16" TOMB RAIDER

23 I DUCT AT 18' -7 AFF.

N MOUNT THE SENSOR AT 18” AFF IN THE BEER COOLER.

42"x20" FLOPPY BIRD W (2) NBA

B 14 20 23 O MOUNT BOTTOM OF

AIR FX P O WRG (TYP 4) HS MOUNT THE CENTRAL PANEL AND ALARM ON THE WALL 48"x22" S B DROP BOX AT 17' -0" AFF 22"x22" WATERFULL DB CANDY CRUSH NEAR THE BEER COOLER. THE LOW LEVEL ALARM SHALL D FUNCTION ROOM TS RTU-10 FUNCTION ROOM 9 10 11 ACTIVATE THE LOCAL AUDIBLE AND VISUAL ALARM. THE DISHWASH CRG 24 (2) TERMINATOR TOMB RAIDER (TYP 2) II HIGH LEVEL ALARM SHALL ACTIVATE RELAY. INSTALL 10"Ø 149 DRY STORAGE I PER MANUFACTURER'S INSTALLATION INSTRUCTIONS. ROAD MACARTHUR 1471 22"x22" 12"x12" (2) NBA (TYP 2) CSD 129 ALARM SET POINTS: LOW LEVEL ALARM - 0.5% = 5,000 CRG UP TO RTU -4 143 128 11 10 350 CFM 7 CO2 TS GARY'S CO2 TS 10 11 PPM HIGH LEVEL ALARM - 3.0% = 30,000 PPM 22"x22" 10"Ø 48"x22" BAR (TYP 2) RTU-7 CRG CSD SINK IT RTU-8 18 INSTALL OWNER FURNISHED ANALOX Ax60+ REMOTE 22"x22" QUICK DROP GUM DROP (2)

N N

I I N N CARBON DIOXIDE SENSOR AND LOCAL AUDIBLE/VISUAL FIELD VERIFICATION 350 CFM 10"Ø 11 10 I I WHACK N WINWHACK N WIN CRG P P (2) BIG BUCK 10"Ø 18"x12" S N W S N W ALARM. MOUNT THE SENSOR AT 18” AFF NEAR THE CO2 Contractor shall verify all figured dimensions 139 (TYP 2) CSD 24"x20" CSD 18"x12" WRG FISH TANK. WIRE THE SENSOR TO THE CENTRAL DISPLAY and conditions at the job site and notify Aria 22"x22" TS FISH 350 CFM BOWL (2) NBA Group Architects, Inc. of any dimensional 350 CFM RTU-4 24"x16" BOWL NEAR THE BEER COOLER. PROVIDE CAT6 PATCH CABLE CRG MOUNT BOTTOM OF VERIFY LOCATION OF HOOD DIZZY errors, omissions or discrepancies before 14"x16" 24"x16" 10"x10" PULL STATIONS WITH INSPECTOR/ 10"Ø 10"Ø CHICKEN WITH RJ45 CONNECTORS. FIELD VERIFY LENGTH beginning or fabricating any work. Do not scale BEER COOLER BEER 36 17 UP TO MAU -1 GRILLE AT 15' -8" AFF. 10"Ø 10"Ø AHJ PRIOR TO ROUGH -IN REQUIRED IN ORDER TO CONNECT REMOTE SENSOR TO these drawings. WSR 10"Ø 10"Ø CSD CSD CSD CSD CONTROL PANEL. INSTALL PER MANUFACTURER'S 10"Ø (TYP 5) 35 300 CFM CSD CSD 275 CFM 275 CFM NFL 2 MIN COPYRIGHT 300 CFM 350 CFM DEPOSIT INSTALLATION INSTRUCTIONS. CSD 22"x22" 48"x22" DRILL Aria Group Architects, Inc. shall retain all CO2 12"Ø 275 CFM 275 CFM 12"x12" COUNTING 3 common law, statutory and other reserved 12"Ø 12"Ø 27 350 CFM 19 AIR CURTAIN MOUNTED ABOVE DOOR. INSTALL PER UP TO MAU -2 CSD2 CRG UP TO RTU -5 138 rights. These drawings and related CSD2 CSD2 PS MANUFACTURER’S RECOMMENDATIONS. 33 HOODS M2.1 documents shall not be duplicated, disclosed 475 CFM 12"Ø 3-5 137 475 CFM 475 CFM 31 20 MOUNT GRILLE HIGH ON WALL AND TIGHT TO or otherwise without written consent of Aria 13 HOODS 12"Ø 22"x22" (TYP) CSD2 16"x12" 32 28 1-2 7 10"x10" 6"Ø 22"x22" STRUCTURE. IF APPLICABLE, MOUNT ABOVE BLACKOUT Group Architects, Inc. M2.1 27 475 CFM CSD CRG 16"x12" 18"x20" WSR CSD CRG 10"Ø (4) BIG BASS WHEELS LINE. REFER TO ARCHITECTURAL PLANS. 24"x20" 32"x20" 475 CFM UP TO RTU -6 10"Ø PUMP IT UP (TYP) 300 CFM 100 CFM CSD 24"x10" PHOTO 21 MOUNT BOTTOM OF GRILLE AT 12’-0” AFF. 60"x20" CSD STORAGE JANITOR II 20 7 BOOTH 8"Ø JANITOR I JANITOR III 6"Ø 275 CFM PIANO UP TO 8"x8" 275 CFM KEY 20"x16" UP CSD 22 MOUNT FAN COIL ABOVE DOOR AT 10'-6" AFF. FIELD 1 34"x20" 26"x20" 20"x20" CSD 24"x10" RTU -13 10"x10" 20"x16" HOOD 3 WEG 8"x8" 131 10"Ø 10"Ø 135 120 TO EF -2 200 CFM 119 ADJUST FINAL LOCATION AS NECESSARY TO AVOID 3 UP TO WRG 10"x10" M2.1 1 16x16 8"Ø 150 CFM (TYP 2) 100 CFM CSD UP TO RTU -7 CSD LOCATING OVER SENSITIVE EQUIPMENT/PHONE BOARD. 16x16 HOOD 5 3 HS HS RTU -8 CEG UP TO KEF -3 11 CSD 10"x22" 10"x10" 8"Ø 14"x14" 8"x6" 23 DROP FULL SIZE RELIEF DUCTWORK DOWN AND TAP (TYP) UP TO KEF -5 HOOD 4 1 2 TRAINING ROOM 275 CFM 18"x18" 7 275 CFM 18"x18" 400 CFM HOOD 2 175 CFM CRG2 7 CEG CSD WEG DUCT INTO TOP OF PLENUM. MOUNT PLENUM TIGHT TO 10 12"x12" UP 20"x16"

160 24"x16" 34"x18" 200 CFM 12 20x20 UP TO KEF -4 16x16 UP TO 2 16x16 TO EF -1 425 CFM 100 CFM 8"x6" BOTTOM OF STRUCTURE. EXTEND PLENUM 3FT AND 1 (TYP 2) 8"Ø 8"x6" 8"x6" E 12"Ø KEF -1 UP TO RTU-5 8"x6" (TYP 2) WSR PROVIDE A WRG GRILLE WHERE INDICATED. M2.1 TS 22"x22" CSD WSR WSR 18"x18" 21 22"x10" 14"x14" 14"x12" CSD2 HOOD 1 3 KEF -2 WSR 10"x22" 75 CFM 24 PROVIDE DUCT TO CEILING RETURN GRILLES TO 12"Ø TSHOODS CRG PS 225 CFM 75 CFM 50 CFM (TYP) 475 CFM 12"Ø 100 CFM CRG2 8"Ø 12"x12" PROVIDE VENTILATION TRANSFER AIR TO KITCHEN. CSD2 4 CSD2 12"x12" 12"x12" FIELD PAINT TO MATCH WALL. COORDINATE COLOR 2 07/26/19 ADD. #1 475 CFM 14"x12" 20"x14" WITH ARCHITECT. 475 CFM 24"x18" 30"x18" 12"Ø 22"x16" 12"x12" (TYP 2) 22"x22" 8"Ø 1 06/17/19 ISSUE FOR 16"x16" CSD2 (TYP 2) 22"x22" 8"x8" RTU-13 25 8”Ø SUPPLY DUCT. BALANCE SUPPLY AIR TO 132 CFM 12"Ø 10"x22" CRG CSD 10"x10" 15 475 CFM T FC-1 TS (TYP 5). 12"Ø 10"x22" 8"x8" PERMIT CSD2 12"Ø CRG2 CRG 225 CFM 6"Ø

10"x10" 10"Ø CSD2 12"Ø 10"x10" CRG2 FC 14 10"x10" 21 12"x10" 26 8”Ø SUPPLY DUCT. BALANCE SUPPLY AIR TO 125 CFM T 475 CFM CSD2 25 26 T 10"x10" 10"Ø 0 06/06/19 90% T EUH-1 29 30 22 CEG 10"x10" (TYP 4). EF-3 475 CFM 475 CFM CSD2 WRG RTU 8"Ø (TYP 2) 1 M2.1 WRG WSR CEG 1-13 STORAGE BOH 450 CFM 10"Ø REVIEW 475 CFM CSD 8"Ø 8"Ø 300 CFM 400 CFM 27 8”Ø SUPPLY DUCT. BALANCE SUPPLY AIR TO 116 CFM SPRINKLER 28"x28" 10"x22" 8"x8" CSD EUH ELECTRICAL 13 MECHANICAL 225 CFM CRG2 CSD CSD 6"Ø AV/ COMP 157 10"Ø (TYP 6). NO. DATE REMARKS 16 ROOM UP TO EF -3 CEG1 159 6"Ø 8"x8" 250 CFM 1 12"x8" 200 CFM 200 CFM CSD1 CSD 28 8”Ø SUPPLY DUCT. BALANCE SUPPLY AIR TO 133 CFM 125 CFM CSD1 CEG1 155 156 75 CFM 124 250 CFM (TYP 6). REVISIONS 157 CO2 75 CFM 125 CFM F 29 PROVIDE TAKE-OFF OF FULL SIZE OF MAKE-UP AIR 12"x8" PLENUM COLLAR SIZE. BALANCE MAKE-UP AIR TO 506 18 AC EMPLOYEE WOMEN'S TOILET MEN'S TOILET 2 WSR 19 CFM (TYP 3). 12 11 1 TOILET 162 M2.1 400 CFM 118 30 PROVIDE TAKE-OFF OF FULL SIZE OF MAKE-UP AIR GM/BA SPECIAL EVENTS MAN TRAP 133 PLENUM COLLAR SIZE. BALANCE MAKE-UP AIR TO 525 CFM (TYP 2). 136 105 164 31 PROVIDE TAKE-OFF OF FULL SIZE OF MAKE-UP AIR PLENUM COLLAR SIZE. BALANCE MAKE-UP AIR TO 593 SERVICE YARD CFM (TYP 3). 154 32 PROVIDE TAKE-OFF OF FULL SIZE OF MAKE-UP AIR PLENUM COLLAR SIZE. BALANCE MAKE-UP AIR TO 738 CFM (TYP 3). 33 PROVIDE TAKE-OFF OF FULL SIZE OF MAKE-UP AIR PLENUM COLLAR SIZE. BALANCE MAKE-UP AIR TO 623 8 7 6 5 4 3 2 1 CFM (TYP 3). 34 COORDINATE SPRINKLER PIPING WITH MECHANICAL DUCTWORK TO CONCEAL PIPING SERVING VESTIBULE Drawing Title SPRINKLERS. SPRINKLER PIPING SHALL BE ROUTED BETWEEN DUCTWORK AND WALL. 35 INSTALL HOOD FIRE SUPPRESSION MANUAL MECHANICAL PULL-STATION, FURNISHED BY HOOD SUPPLIER PER EP EP v19_justinfox_20190726160941.rvt NFPA 96 REQUIREMENTS. COORDINATE LOCATION WITH FLOOR PLAN KITCHEN EQUIPMENT CONTRACTOR AND LOCAL AHJ. 36 PROVIDE CAT6 PATCH CABLE WITH RJ45 CONNECTORS FOR ANALOX CO2 SYSTEM. FIELD VERIFY LENGTH MECHANICAL FLOOR PLAN REQUIRED IN ORDER TO CONNECT SENSORS TO THE Job No. Drawn 1 CONTROL PANEL. 1/8" = 1'-0" N 184150 Author PROVIDE DUCT LINER IN ALL EXPOSED DUCTWORK. REFERENCE SPECIFICATIONS. COORDINATE WITH G.C. TO PROVIDE CEILING OVERLAY Scale Date SHOP DRAWING WITH ALL CEILING DEVICES, DUCTWORK AND PIPING RUNS SHOWN INCLUDING ELEVATIONS AND 1/8" = 1'-0" 06/06/2019 COORDINATION WITH EXISTING CONDITIONS. G.C. SHALL PROVIDE ALL DISCIPLINES ON ONE REFLECTED CEILING VIEW. NOTE: Sheet No. ADJUST AIRFLOW DIFFUSION PATTERN AS REQUIRED TO EXISTING CONDITIONS WERE TAKEN FROM ORIGINAL DRAWINGS & PREVENT DRAFTS AND PROVIDE UNIFORM AIR SITE VISITS AND MAY NOT REFLECT EXACT "AS -BUILT" CONDITIONS. DISTRIBUTION TO SPACE. FIELD VERIFY ALL EXISTING CONDITIONS PRIOR TO SUBMITTING FINAL BIDS. CAREFULLY COORDINATE NEW WORK AND DEMOLITION INSTALL DUCTWORK AND PIPING AS TIGHT AS POSSIBLE M1.1 WITH ALL OTHER DISCIPLINES AND EXISTING CONDITIONS. TO BOTTOM OF STRUCTURE U.N.O. C:\Revit\Projects\1950001061 D&B LeHigh Valley PAM Valley LeHigh D&B C:\Revit\Projects\1950001061 SEAN O. EISLER O. SEAN

WHITEHALL, PA 18052 PA WHITEHALL, ROAD MACARTHUR 1471 1950001061 Author

06/06/2019

WWW.HENDERSONENGINEERS.COM PERMIT REVIEW Drawn Date

1.4.00913.742.5001 913.742.5000 FAX TEL

LENEXA, KS 66214 KS LENEXA, 60301 300 SUITE DRIVE, LENEXA 8345 Illinois DETAILS REVISIONS Oak Park, G R O U P R O G ariainc.com M2.1 MECHANICAL 708-445-8400 184150 830 North Blvd. 12" = 1'-0" 12" = Contractor shall verify all figured dimensions and conditions at the job site and notify Aria Group Architects, Inc. of any dimensional errors, omissions or discrepancies before beginning or fabricating any work. Do not scale these drawings. common law, statutory and other reserved rights. These drawings and related documents shall not be duplicated, disclosed or otherwise without written consent of Aria Group Architects, Inc. Aria Group Architects, Inc. shall retain all ARIA GROUP ARCHITECTS, INC. ARCHITECTS, GROUP ARIA FIELD VERIFICATION FIELD COPYRIGHT JobNo. Scale No. Sheet NO. DATE REMARKS DrawingTitle 21 07/26/19#1 ADD. 06/17/190FOR ISSUE 06/06/19 90% LITION LITION GS & . TTING TTING BUILT" CONDITIONS. CONDITIONS. BUILT" - PROVIDE 45° PROVIDE WHEN TRANSITION TAPS RECTANGULAR IN SHOWN ARE VIEW PLAN RETURN AIR RETURN OPENING PLANS) (REF SHEET METAL SHEET SCREW 24"Ø) (MAX. BOLT AND BOLT NUT 36"Ø) (MAX. 4'-0" MIN 4'-0" PLANS) (REF LOADS MUST LOADS BE HUNG6" WITHIN OFPANEL POINTS IS PROVIDED IS FASTENER TYPES FASTENER 6" ROOF DECK ROOF AIRFLOW AIRFLOW FLEXIBLE CONNECTION ALLATION. ROOF ON NO LARGER THAN LARGER NO ON LANS FOR DUCT SIZES. FOR LANS DUCT , WIRES , OR ND RETURN OPENINGS. RETURN ND JOIST FASTENER RETURN AIR PLENUM PLENUM AIR RETURN INSTALLED TIGHT TO STRUCTURE FASTENER ROOF NOTE: WERE DRAWIN CONDITIONS TAKEN FROM ORIGINAL EXISTING "AS EXACT NOT REFLECT AND MAY VISITS SITE SUBMITO PRIOR CONDITIONS EXISTING ALL VERIFY FIELD NEW COORDINATE CAREFULLY WORK BIDS. DEMO AND FINAL CONDITIONS EXISTING AND OTHER WITHDISCIPLINES ALL W SUPPLY SUPPLY AIR DUCT PLENUM

RETURN AIR RETURN

o R IN NTS ROUND DUCT DETAIL SUPPORT DUCT ROUND

6" R 6 ROUND SUPPLY

AIR DUCT AIR STEEL

i R ROOFTOP ROOFTOP UNIT W = DUCT WIDTH DUCT W= 1.0W] 2W,= = Ri [Ro 1.5W (MAX) = R 90° THAN LESS ANGLE ELBOW SHOWN.OTHER 90° IF NOTE: SHOWN ABOVE. DIMENSIONS RADIUS USE NTS NTS ROOFTOP ROOFTOP UNIT WITHDETAIL DROPBOX GREASE RADIUS ELBOWDUCT DETAIL BOTTOMOF STRUCTURE 16 GA. GALV. GA.GALV. 16 ROUNDDUCT TWIST STRAP TWIST LANDLORD PROVIDED LANDLORD BAND (2" WIDE) BAND(2" 1 11 CONCEALEDAREAS OPTIONAL ROUTING ROUTING OPTIONAL ANGLE OR UNISTRUT ANGLE PROVIDE OPENING THROUGH ROOF AND ROOF DECK INSULATI DECK ROOF AND ROOF THROUGH OPENING PROVIDE TO ALLOW REQUIRED TO TO DUCTS P REFER THROUGH. PASS TO CURB A SUPPLY RTU ROOF IN AS REQUIRED TRANSITION INST CURB ROOF DRAWINGS FOR ARCHITECTURAL REFERENCE NOTES: 1. 2. TOSUPPORT DUCT FROM EACHSIDE. NOTES: FORUSETWODUCTS LARGER THAN36"Ø, 1. HANGER RODS STRAPS PROVIDED LANDLORD LANDLORD INSULATED PERPENDICULAR TO STRUCTURE TO PERPENDICULAR ROOF CURB ROOF PARALLEL TOSTRUCTURE PARALLEL INSULATED SUPPLY AIR INSULATED (REF OR DROPBOX PLENUM MOUNTING FOR PLANS HEIGHT) FLOOR MOUNT THERMOSTATS 6" O.C. 6" THERMOSTATS MOUNT DIRECTION. VERTICAL THE IN INSTALL TO PRIOR VERIFY MANUFACTURER WITH FOR CUTSHEETS AND INSTALLATION (TYP) DIMENSIONS. EXHAUST FAN EXHAUST ROOFCURB STEEL STAINLESS DUCT EXHAUST STEEL STAINLESS TRANSITION STAINLESS EXHAUST STEEL DUCT DISHWASHER THERMOSTAT (TYP) THERMOSTAT REFER TO MECHANICAL/FIRE TO REFER OF QUANTITY EXACT FOR SHEETS TEST THERMOSTATS/REMOTE STATIONS. CEILING MOUNT REMOTE TEST STATIONS 4" STATIONS TEST REMOTE MOUNT DIRECTION. HORIZONTAL THE IN O.C. WITH INSTALL TO PRIOR VERIFY FOR CUTSHEETS MANUFACTURER (TYP) DIMENSIONS. AND INSTALLATION GUARDSPARK - SIDE VIEW SIDE H NFPA, AND ALL LOCAL ANDHALL NFPA, ENCLOSURE OF RATED NLIEU STAINLESS STEEL STEEL STAINLESS ENCLOSURE AS/IF TOCEILING PANEL REQUIRED R APPROVAL PRIOR TO APPROVALPRIOR R IRE PROTECTION CONTRACTOR PROTECTION IRE AND FRONT EDGEOF FOOD ESTING REQUIRED. REQUIRED. ESTING GREASE EXHAUST DUCT GREASEEXHAUST WRAP WITHFIRE PER SPECIFICATIONS HOOD 3" STANDOFF REFERENCEOTHER SHEETFOR THIS DETAILS AND ROOFPENETRATION CONNECTIONS FAN FLAME ARRESTORFILTERS GREASE WITH GREASEDRAIN REMOVABLECUP HOOD EXHAUST LIGHTS EQUIPMENT COOKING ROOFJOIST DESIGNER NOTE: VERIFY ON PLAN THAT YOU HAVE 36" HAVE YOU THAT PLAN ON VERIFY NOTE: DESIGNER MORE IF SENSORS. RTU 15 FOR SPACE WALL CLEAR AVAILABLE. IS SPACE WALL IF HORIZONTAL EXPANDED DOOR) THE BEHIND (LOCATE MOUNT CENTER OF TOP ROW OF ROW TOP OF CENTER MOUNT TO REFER 48"AFF. AT THERMOSTATS FOR SHEETS MECHANICAL/FIRE OFFICE WITH COORDINATE LOCATION. LOCATION. FINAL ON EQUIPMENT MOUNT THERMOSTATS 7" O.C. 7" THERMOSTATS MOUNT HORIZONTAL THE IN PRIOR VERIFY DIRECTION. WITH INSTALL TO CUTSHEETS MANUFACTURER AND INSTALLATION FOR (TYP) DIMENSIONS. 6"MIN. KEH NTS DISHWASHERDETAIL DUCT EXHAUST CONFIRM WHAT IS BEING PROVIDED BY KITCHEN EQUIPMENT KITCHEN BY PROVIDED CONFIRMWHAT BEING IS AND OF MECHANICAL CONTRACTORLOCATION AND EXACT CONNECTION POINTS. ELECTRICAL FRONTVIEW 7 NOTES: 1. ROOFCURB ROOFDECK NTS TYPICALOFFICE ELEVATION THERMOSTAT MECHANICAL MECHANICAL CONTRACTOR PROVIDED 2 SHEETS - KEC PROVIDED, SEE KECPROVIDED, K HEIGHT REFER TO REFER GREASEMASTER MOUNT THERMOSTATS MOUNT DOOR BEHIND MOUNT REMOTE TEST REMOTE MOUNT THE IN O.C. 7" STATIONS VERIFY DIRECTION. VERTICAL WITH INSTALL TO PRIOR CUTSHEETS MANUFACTURER AND INSTALLATION FOR (TYP) DIMENSIONS. OF BOTTOM MOUNT TEST REMOTE OF FACEPLATE OF TOP ABOVE 1" STATION CONTROL THERMOSTAT TO PRIOR VERIFY MODULE. MANUFACTURER WITH INSTALL FOR CUTSHEETS AND INSTALLATION (TYP) DIMENSIONS. DOOR SUBMIT SHOP DRAWINGS OF ALL HOOD SYSTEMS TO CITY FO SHOPDRAWINGS TOHOOD CITY SUBMIT OFSYSTEMS ALL INSTALLATION. COMPLETE CONFORMANCE IN HOODTO BE TOTAL WIT SYSTEM CODESAND REGULATIONS. WITH F SYSTEMS PROTECTION FIRE ANSUL ALL COORDINATE AND T PERMITS FOR WHOALL RESPONSIBLE BE ALSO SHALL WRAP PROVIDE WHERE CODES SYSTEM LOCAL I APPROVED BY CODE. LOCAL BY REQUIRED AS ACCESS PANELS PROVIDE OPENSIDES ALL BEYOND 6" MINIMUM HOODSEXTEND SHALL SERVED. EQUIPMENTBEING COOKING SHEETS FOR MOUNTING FORSHEETS UP AIR SUPPLY DIFFUSER SUPPLY UPAIR - NOTES: 1. 2. 3. 4. 5. 6. ROOF FLOOR NTS MAKE MAKEUP AIR DUCT AIR MAKEUP DUCT AIR SUPPLY PANEL ACCESS CEILING DIFFUSER SUPPLY AIR SUPPLY CEILING TYPICAL KITCHEN EXHAUST HOOD ELEVATION TYPICALHOOD KITCHEN EXHAUST 12 SECURE EXHAUST FAN SECUREEXHAUST COVER, TOGALVANIZED CONNECTION SEAL WEATHERTIGHT OVERSIZED COVER GALVANIZED TWOGALVANIZED PIECE AND COUNTERFLASHING CURB 8 COUNTERBALANCED BACKDRAFT NOTED (UNLESS OTHERWISE) DAMPER,TOSECUREDUCT FROM ABOVETO ALLOWOR SERVICE REMOVALOFDAMPER FROM ROOF UPTHROUGH DUCT EXHAUST AND SIZE FOR PLANS ROOF. SEE LOCATION. 11 INSULATED DUCT INSULATED 10 7 FLEXIBLE DUCT WITHIN FLEXIBLE CT LENGTH DOESNOT LENGTH CT EXCEED 6 5 9 COVER m) ) MMENDATIONS. 4 NTS UPBLAST EXHAUST FAN UPBLASTDETAIL EXHAUST INSULATION (TYPICAL) INSULATION METALLIC BAND OVER METALLIC 8 - 3 FOIL TAPE AT TAPE FOIL NTS LAY-INCEILING DIFFUSER DETAIL 2 INSULATION JOINT INSULATION 3 1 BAND METALLIC OR NON METALLIC DUCTAND FAN (TYPICAL) METALLIC METALLIC - EXHAUST FAN EXHAUST ROOFDECKTO REFER GASKET BETWEEN GASKET SEE NOTE1. SEE INSTALL NEOPRENE INSTALL NTS GREASE DUCT CLEANOUT ACCESS GREASE CLEANOUT DOOR DUCT METALLIC OR METALLIC NON AS SCHEDULED AS WITHBIRDSCREEN WELDED 16 GAUGE 16 ROOFINSULATION ARCHITECTURAL DRAWINGS ARCHITECTURAL - 13 - CEILING DIFFUSER CEILING 0". PROVIDE RIGID 90° ELBOW 90° WHERE RIGID TO KEEP PROVIDE REQUIRED 0". LIMITATION. LENGTH 0" HIGH EFFICIENCY TAKEOFF EXTERNALLY INSULATED, EXTERNALLY TAKEOFF EFFICIENCY HIGH ANDSHARP TURNS - - CEILING DUCTREQUIRED, AS EXTEND RIGID METAL DUCT SO THAT MAXIMUM FLEXIBLE DU FLEXIBLE METAL DUCTMAXIMUM THAT SO RIGID EXTEND 5' 5' INSULATED FLEXIBLE INSULATED TO PREVENT KINKING TO - INSTALL PERMANENTLY INSTALL 1. SEALED AND SUPPORTED SEALED PRE NOTES: WITHVOLUME DAMPER DAMPER AND LOCKWITH EXTENSION ACCESSHOLE (6mm) IN. 1/4 DIAMETERTHREADED ALL RODS ACCESS COVER INSULATED PINS BARRIER FIRE LAYER FIRST DUCT WRAP CUT SAME AS SIZE SECOND BARRIER FIRE LAYER DUCTWRAP WITH (25m 1 IN. SIDES ONOVERLAP ALL WRAPDUCT (25mm BARRIER WITHIN. FIRE 1 LAYER THIRD LAYER OFPREVIOUS SIDES ONOVERLAP ALL SPEED CLIPS ALUMINUM TAPECOVERING ALL EXPOSED EDGES THREADED FOR RODS SPOOLPIECES WING (6mm) NUTS DIAMETER IN. 1/4 1 2 3 4 5 6 7 8 9 10 11 FOR REFERENCE ONLY. INSTALL PER MANUFACTURERSPER RECO INSTALL FORREFERENCE ONLY. ROOFINSULATION SECURE EXHAUST FAN FAN SECUREEXHAUST TO ROOFCURB 1/2" X 1/4" 1/4" X 1/2" - EXHAUST FAN EXHAUST WITHBIRDSCREEN EXHAUST DUCT UPTHROUGH EXHAUST FOR PLANS SIZE ROOF.SEE ANDLOCATION. ROOFDECKTO REFER ARCHITECTURAL DRAWINGS DAMPER SCEHDULE, PER SECUREFROMTODUCT ABOVEORTO ALLOW SERVICE REMOVALDAMPEROF FROM ROOF 1/2" X 2 X 1/2" - 2 ANGLEFRAME STEEL 6" MAX 6" EQUIPMENT CURB EQUIPMENT WELDCONTINUOUS STEEL FRAME ANGLE TOMETAL ROOFDECK 10"MAX EVAPORATORCOIL ABOVE BELOWOR CU) PITCH REFRIGERANT PITCH TOWARDS GASLINE THE INCH 1 AT INDOORCOIL FEET. PER10 GLASS SIGHT THERMALEXPANSION (TXV) VALVE ICH SHALL TAKE SHALL ICH E TRAPS BASED ON THE BASED TRAPS E ALL A SOLENOID VALVE IN THE IN VALVE SOLENOID A ALL LOCATE TXV SENSING BULB ON BULB SENSING LOCATETXV AND 7/8" FOR PIPE TOPOF PIPE BELOW 45° SMALLER, CENTERLINE THANGREATER FORPIPE OFPIPE 7/8". ECOMMENDEDTHE BY CONSTRUCTION AND CONSTRUCTION EXTERNAL . MANUFACTURER CONSULT AND DISTRIBUTOR. REFRIGERANT A ITH CONFORMANCE WITH ALL ELEVATION SECTION NTS DOWNBLAST FAN DETAIL EXHAUST 9 NTS SECURITYBARS AT OPENING ROOF SHUTOFF VALVES. OMIT IF THE IF OMIT SHUTOFFVALVES. WITH EQUIPPED IS CONDENSINGUNIT VALVES SHUTOFF INTEGRAL (SUCTION) GAS LINE REFRIGERANT LINE LIQUID REFRIGERANT EXTERNAL 4 (SEE NOTE 5). (SEE EQUALIZER LINE LINE EQUALIZER DRIER AND SITE GLASS. ANDSITE DRIER ROOF - ANDROOF INDOOR COIL AT 1 AT INDOORCOIL INCH PER 10 FEET. 10 PER INCH STRUCTURE PITCH REFRIGERANT PITCH (TYP) GAS LINE AWAY FROM LINE GAS CAULK AND SEAL AIRTIGHT SEAL CAULKAND TOCURB NAILER SECURELY TODUCT SECURELY FASTEN ANGLEIRON FASTEN #4 STAINLESS #4 OVER TOPCURB, OVEROF EXTEND DUCTWORK EXTEND SECUREDUCTWORK WELDTO BARS STEEL BAR(TYP) STEEL ANGLES AT BOTH ANGLESAT DUCTWITH FLANGE.

STEEL ANGLE FRAME ANGLE STEEL ENDS OFEACH ENDSBAR DRIER IN DRIER ROOF ABOVE - CAULK AND SEAL DUCT AND SEAL CAULK CONNECTIONAIRTIGHT

MAY EXIST. MAY

DRIER THAT DRIER

- HEIGHT DISCHARGE ATTACH DUCT FLANGE TO ATTACHDUCT FLANGE ABOVE ROOF ABOVE

0 IN M 40"

GRADEOR ROOF DUCTWORK WELDED UNIT MINIMUM 18" DRIER. OMIT IF THE IF OMIT DRIER. WALLUL - - CONDENSING INSTALL REFRIGERANT PIPING AND COMPONENTS STRICT AND IN PIPING REFRIGERANT INSTALL MANUFACTURER'SRECOMMENDATIONS WH REQUIREMENTS, AND DETAIL THIS IN PRESENTED PRECEDENTOVER INFORMATION MODEL R EXACT THE BE SHALL COMPONENTS ALL INSTALLED MANUFACTURERWITHOUT EXCEPTION. MANUFACTURERNEEDTHETOCONSULTINST THE REGARDING BETWEEN FILTER LINE THE LIQUID RECOMMENDEDTHE BY SIZES PIPE REFRIGERATION INSTALL MANUFACTURER NEEDTHE FOR THEREGARDING INTERMEDIAT CONFIGURATION. PIPING AND RECOMMENDEDSIZES PIPE WITH PORT BALANCED VALVE EXPANSION THERMAL INSTALL W EQUIPPED EVAPORATORCOILS ALL FOR LINES EQUALIZER DRIER IS INSTALLED NEAR INSTALLED IS DRIER - CONFIGURATION IS WITHIN IS CONFIGURATION FILTER ABOVE THE LOWEST ABOVETHE POINT. NOTES: 1. 2. 3. 4. 5. THREADED ROD(TYP) JOIST INSTALL RISER AT INDOORCOIL AT RISER INSTALL ANY OTHER FILTER ANY NTS CONDENSING UNIT IS EQUIPPED IS UNIT CONDENSING REFRIGERANT REFRIGERANT PIPING DETAIL WITH (SINGLE CIRCUIT COIL WITH TOP A MINIMUM OF 1 FOOT OF 1 MINIMUM WITH TOPA 6" THE LIQUID LINE ANDPIPING THE LINE THELIQUID FILTER WEATHERPROOF (NEMA 3R) DISCONNECT SWITCH BASEHINGE FAN THEEVAPORATOR,REMOVE THEN MANUFACTURER FOR ITS USE. IF A IF USE. MANUFACTURERFOR ITS PARAMETERS PRESCRIBED BY THE BY PARAMETERSPRESCRIBED OVERSIZED OVERSIZED GALVANIZED COVER WITH AN INTEGRAL FILTER WITHANINTEGRAL 14 SHEET METAL SCREWSSEE (TYP) NOTE2. HIGHER THAN HIGHER OWNERFURNISHED GREASEGUARD OR WRAPPEDGAIRON, BLACK 16 DOUBLE CONCENTRIC GREASEDUCT RATED LISTED FORCLEARANCE ZERO TO FOR PLANS SEE COMBUSTIBLES. LOCATION. AND SIZE AP IS CONTINUOUS IS AP WIDE. ER IS GREATER. ERIS CLEARANCE GREASECLEARANCE DUCT - HANGERSTRAP NOTE 1. SEE 60" (MAX) 60" ANGLE ORANGLE UNISTRUT ANGLE OR ANGLE UNISTRUT RECTANGULARDUCT ROOF 1" MIN 1" FORUSEWITH ZERO 6" ROOF E NTS NTS UPBLAST FANGREASEDETAIL EXHAUST SUPPORT DETAIL DUCT RECTANGULAR 5 10 STRUCTUR BOTTOMOF HUNG WITHIN 6" 6" HUNG WITHIN LOADS MUSTLOADS BE INSTALL INSTALL OF PANEL POINTS OFPANEL LOOPS UNDER ENTIRE DUCT. LOOPSUNDER ENTIRE AIRTIGHT WALL U.L. - NOTES: USETHREADED DUCTS LARGERROD 60"Ø THAN FOR 1. ALL HANGER SCREWS STR SHEETMETAL IF OMITTED BE 2. MAY AND NEOPRENE ADJACENT BUILDING STRUCTURE WITHIN 10 FEET, WHICHEV FEET, 10 STRUCTURE WITHIN ADJACENTBUILDING LISTED ZERO LISTED DISCHARGE HEIGHT ABOVE ROOF SURFACEOR ELEVATION ATHEIGHT DISCHARGE GREASETRAP VENTEDCURB ROOFDECK TO REFER - EXHAUST FAN EXHAUST PROVIDED AND PROVIDED DUCTAND FAN EXTENSION. IF A A IF EXTENSION. CURB VENTED IS DOUBLE ROOFINSULATION INTERIOR OF CURBOF INTERIOR GASKET BETWEEN GASKET NON WITHBIRDSCREEN ARCHITECTURAL DRAWINGS ARCHITECTURAL OPENINGS AND SEAL AND SEAL OPENINGS CLEARANCE GREASE CLEARANCE BLANK OFF PANELS ON PANELS OFF BLANK PARALLEL TOSTRUCTURE PARALLEL DUCT IS USED, PROVIDE PROVIDE USED, IS DUCT PERPENDICULAR TOSTRUCTURE PERPENDICULAR

GREASE FLANGE TRANSITION TRANSITION GREASEFLANGE SHOWN TODUCT SIZE ON PLAN

EP v19_justinfox_20190726160941.rvt EP M PA Valley LeHigh D&B C:\Revit\Projects\1950001061 SEAN O. EISLER O. SEAN SEAN O. EISLER

C:\Revit\Projects\1950001061 D&B LeHigh Valley PA MEP v19_justinfox_20190726160941.rvt 24. 23. 22. 21. 20. 19. 18. 17. 16. 15. 14. 13. 12. 11. 10. 9. 8. 7. 6. 5. 4. 3. 2. 1. NOTES: NEW GENERAL 35. 34. 33. 32. 31. 30. 29. 28. 27. 26. 25. REFER TO THE FOLLOWING SPECIFICATION REFERTHE TO FOLLOWING SECTIONS A FOR REFRIGERANT MATCHING EXISTI SYSTEMS NEW WITH CHARGE MANUFACTURER WITH INPROJECT ACCORDANCE FULLY EXISTING CHARGE REFRIGERANT SYSTEMS BEING REU IFINSTRUCTIONS MANUFACTURER THEY FROM ARE AVAI NOT MANUFACTURER WITH ACCORDANCE LUBRICATE EXISTING BEING EQUIPMENT THIS FOR REUSED PRIOR STARTINGTO PUMPS. CONDITION STRAINENOTED. CLEAN OTHERWISE UNLESS NEW EXISTING EQUIPMENTTHE TO EQUAL IN AND PERFORMANCE FILTERSPRIOR EQUIPMENT. STARTUP OF TO SHALL NEW BE FILTERSTHIS PROVIDE PROJECT. EXISTING FOR NEW AIR EXISTINGCLEAN B EQUIPMENT AND COMPONENTS EQUIPMENT OPERATION AND RESULTS THE OF TESTS. ARCHITECT AND DESCRIBING REPORT A WRITTEN TESTS PER ANYREPORT DEFICIENCIES ARCHITECT. OR THE TO OWNER FOR THIS REUSED AND IS IS PROJECT IN DAMAGED NOT GO FIELD VERIFY THAT THE EXISTING EQUIPMENT INCLUDING BALANCING TURNING BEFORE AND SYSTEM(S) OWNE TO OVER SET AIR OF PROVIDE A FILTERSNEW IN UNITS PRIOR TO ADDITIONAL INFORMATION. TYPICALREFERENCE EXHAUST GREASE SYSTEM DETAIL S ON BY IF RECTANGULAR AND ACCEPTABLE LEAD ALLOWED AHJ T REFERSPECIFICATIONS. TO ENCLOSURES, DURASYST ALLOW MEETING E2336REQUIREMENTS UL AND ASTM REQUIREMENTS MINIMUM OF 1/4" LINEALPER FOOT. PROVIDE APPROVE AN REQUIRED BY NFPA 96 LOCALSLOPE BACCODES. AND DUCT IRONLIQUID WITH PANELS ACCESS FO WITH TIGHT WELDS, PROVIDE TYPE MINI OF I EXHAUST HOOD DUCTWORK GREASE 2AND A MINIMUM ROOF 10' OF THROUGH AND EQUIPMENT SPECIFICATIONS.RECOMMENDATIONS KEEP PROVIDE EQUIPMENT VENTS FLUES AND EQUIPMENT PER MAN SPECIFICATIONS ADDITIONAL FOR REQUIREMENTS. AVOID TO SUPPORTED AND BENDS SAGGING.AND REF SHARP FLEXIBLE SHALL NOT EXCEED 5 DUCTWORK THICKNESSFOR LINER. DUCT OF DIMENSIONS,AIRFLOW INCREASE SHEET SIZES METAL ACCO SIZESREQUIREMENTS. DUCT MECHANICAL ON PLANS INDICA REFERSPECIFICATIONS TO PIPING AND INS DUCTWORK FOR NOTED. OTHERWISE UNLESS TO AIR OUTLETS SHALL SIZE BE SAME DUCTWORK BRANCH A PLANS. LOCKINGBALANCINGWHERE AND MANUAL DAMPER QUADRANT INDIVIDUALTO DIFFUSERS, REGISTERS, AND GRILLES. PR TAKEOFF DUCT FITTINGBRANCH CONNECT DUCT BRANCH FOR PROVIDE A PREFABRICATED 45 HIGH DEGREE, EFFICIENCY, AND EXHAUST OUTDOOR AIRRETURN, DUCTS. PROVIDE AIN MANUAL BALANCING DAMPER TAKE EACH DUCT WALL DIVISIONS.OTHER WILL BE REIMBURSEDNOT CONTRACTOR BETHAT ARCHITECTURAL TO ARE THE ON DRAWINGS SHOWN PRESENTATION DISPLAY BOARDS, CABINETS, SHELVES, OR COORDINATE THE LOCATION ELEVATIONAND WALL OF THE BOXJUNCTION FROM 6 TO THE WALL INWIRING CONDUIT PROVIDED BY DIVISION 26. AT A MIN EXTERIOR ON BACKING MOUNTED BUILDIN FOR THERMOSTATS PLANS. ON PROVI REQUIREMENTS NOTED OTHERWISE UNLESS INSTALL DEVICES DEVICE OF TOP WITH AT MAXIMUM 48 PLANS. VERIFY EXACT LOCATIONS ARCHITECT WITH PRIOR AND ANDLOCATE HUMIDISTATS SET THERMOSTATS AT LOCAT SIZE DUCT SECTIONIS WHERE SMALL TOO FOR A 10 10 SHALL PANEL ACCESS FIRE/SMOKEM BE DOOR OR DAMPERS. ACC FOR PANELS ACCESS DOORS OR DUCT OR PROVIDE WALL REQUIREMENTS OF INSTALLEDWITH LOCATION. TO AS NFPA APPLICABLE. SHALL CONFORM DAMPERS COORDI THE ON CEILINGSPLANS. AT LOCATIONS AND SHOWN WALLS PROVIDE FIRE ASFIRE/SMOKE OR APPLICABLE, DAMPERS, SHALL MINIMUMBE SHEET 26 METAL. GAUGE OTHER FIRECROSSING FIREOR RA RATED WALLS DUCTWORK FINAL CEILING ACCOMMODATE TO GRID LIGHTING AND LOCA LOCATIONADJUST CEILING OF DIFFUSERS, REGISTERS AND INSTALLATIONDUCT REQUIREMENTS. REGISTERS, GRILLES AND THE SUPPLIER WITH MEET TO TH COORDINATE THE EXACT SIZEMOUNTING TYPE FRAME AND O U.L. WITH REQUIREMENTS. IN COMPONENTS ACCORDANCE SPECIFICATIONS.THE CONTRACT FIREPROOF PENETRATIONS SEAL THE PENETRATIONSBUILDING THROUGH I COMPONENTS REPLACEMENT. TO ENABLE PANELS/DOORS ACCESS SERVICE OF EQUIPMENT COORDINATE LOCATION LOCA EQUIPMENT OF WITH SUPPORTS INSERTS BYIN SLABS THE SPECIFCONCRETE ALLOWED ARE EXCEPT TO ABOVE SUPPORTS SLABTHE FLOOR AND ROOF OR SHALL FASTENED BE BUILDINGTO JOISTS N BEAMS. DO OR EQUIPMENT, FOR DUCTWO SUPPORTS AND HANGERS OVERHEAD NOTED. OR SHOWN OTHERWISE PIPINGAND INSTALL PARALLEL DUCTWORK TO BUILDING CO SHALL OPERATED ALSO CLEANED.BE THAT WERE THE INTERNAL AND ASSOCIATED SURFACES COILSOWNER. O FILTERS INSTALLEDARE NEW AND PRIOR TURNING TO SYST DURING THEOPERATED CONSTRUCTI UNITSHVAC THAT WERE CLEANINGDUCT CLEAN COMPANY SHALLANY VACUUM DUCTWO CE 238500 238123 237413 237339 233813 233723 233713 233433 233423 233300 233113 232300 230700 230593 230553 230550 230529 230513 230510 230500 230015 230010 230000 REQUIREMENTS: ” AND SHALLAND BE INSTALLED WITHIN 12 - ’ MOUNTED DEVICES BY CAUSED MOUNTED A LACKCOORDINATION. OF - 0 ” FROM ROOF PARAPETS. ROOF FROM ELECTRIC HEATING UNITS AIR ROOM COMPUTER HEATING PACKAGED AND COOLING UNITSOUTDOOR DIRECT COMMERCIAL KITCHEN HOODS GRAVITYHVAC VENTILATORS DIFFUSERS, REGISTERS & GRILLES AIR CURTAINS VENTILATORS POWER HVAC AIR ACCESSORIES DUCT METAL DUCTS REFRIGERANT PIPING INSULATIONHVAC TESTING, ANDADJUSTING, BALANCING FOR HVAC IDENTIFICATION PIPING HVAC FOR AND EQUIPMENT VIBRATION ISOLATION HVAC PIPINGFOR EQUIPMENTAND PIPINGFOR HVAC SUPPORTS AND HANGERS EQUIPMENT AND HVAC EQUIPMENTREQUIREMENTS FOR MOTOR COMMON BASIC PIPING MATERIALS METHODS AND HVACRESULTS FOR WORK COMMON ELECTRICAL COORDINATION MECHANICAL EQUIPMENTFOR MECHANICALGENERAL REQUIREMENTS TOC - FIRED HEATING VENTILATING AND UNITS - 0" FROM HVAC EQUIPMENT0"AIR HVAC FROM FRESH INLETS ’ S WRITTEN INSTRUCTIONS.S WRITTEN OBTAIN ” OF DAMPER. DAMPER. PROVIDEOF DUCT A REMOVABLE ” ABOVE THEABOVE CEILING. ’ - - 0 CONDITIONERS ” IN AND SHALLLENGTH BE INSTALLED ’ S RECOMMENDATIONS REGARDING REGARDING S RECOMMENDATIONS ’ S WRITTEN INSTRUCTIONS.S WRITTEN ” BY 1 0 - ” MOUNTED DEVICES WITH MOUNTED IMUM, IMUM, PROVIDE CONDUIT IN OME FULLYOME ACQUAINTED AFF TO MEET ADA ADA AFF MEET TO TESTING, ADJUSTING AND OVIDE WITH INTEGRALOVIDE WITH HANDLING EQUIPMENT STALLED DELIVERED) AND OF THE CONSTRUCTION THEOF CONSTRUCTION XTURES, ANYETC. ACCESSORIES BEING D DUCT WRAP SYSTEM DWRAP DUCT ” IN DUCTWORK AT IN DUCTWORK OT ATTACH HANGERS ATTACH OT HANGERS R GREASE CLEANINGR GREASE AS RECTANGULAR/ROUND RECTANGULAR/ROUND NDENT, NDENT, PROFESSIONAL TO INSTALLATION. E CEILING, AND WALL, THE NOTES, GENERAL OD WORKING ORDER. ORDER. WORKING OD RRUPTION SERVICE. OF TRADES EOTHER WITH AND NSTALL DUCTWORK PROJECT INPROJECT OTHER COMPONENTS COMPONENTS OTHER BRIS FROM GRILLES AS REQUIRED ACCESS DOOR.ACCESS VERIFY THAT FINAL HE SPECIFICATIONS. EM OVER TO THE TO OVER EM COMPATIBLE THE WITH ON NETRATIONS SHOWN AND PIPING TO WORK LUMN LINESLUMN UNLESS SUBMIT TO THE OWNER SUBMIT THE TO OWNER TIONS. ULATION EQUIREMENTS, WHICH DDITIONAL ICATIONS. K TOWARDS HOOD AT HOOD K TOWARDS RELOCATIONFOR OF LE. SEAL ANY OR TEARS STING AND SURFACES O THE OWNER. O THE TE CLEAR INSIDE RDINGLY ACCOUNT TO FIRE FIRE/SMOKE AND WILL WILL BE THE EXISTING FILTERS AT S OUTLET SIZENECK MS WITH OTHER WITH MS FORMED TO VERIFY TO FORMED ANY TIME DURING LABLE THEAT SITE. IMES AVAILABLE.ARE OFF FROM SUPPLY,OFF FROM SED FOR THIS FOR SED ANYF UNITS HVAC ICAL SYSTEMS IN THE THROUGH FIRE RATED THROUGH AT SHOWN F F DIFFUSERS, HEET M2.1 FOR PREFAB EM 16 BLACK MUM GAUGE INIMUM SIZE 10 OF NATE SLEEVE LENGTH AND/OR FILTER ER TO TO ER CONFLICTS OF OR IONS SHOWN ON ON IONS SHOWN AS REQUIRED FIT TO WORK, NEW NG PENETRATIONS NSTRUCTION AT NO RS IN PIPING SYSTEMS PIPINGAND INSTALLED UNDER N ACCORDANCE WITH WITH ACCORDANCE N TED ASSEMBLIES DRAWINGS. NG. , PAINT, AND UFACTURERS UFACTURERS R. WHERE CONCRETE CONCRETE WHERE PERIODON AFTER SHALLANS BE FOR GREASE GREASE DUCT FOR IS RESULTING FROM G WALLS. INSTALL WALLS. G EING REUSED EING REUSED FOR INSULATEDDE IONS AND TAKE ESS FIRETO AND TION EQUIPMENT OF AND ROOF AND ROOF R R MINIMIZETO RK AND PIPING AND RK CTION DETAILS AS ND EQUIPMENT.ND IS BEING INDICATED ON RK CONNECTED TO TO CONNECTED RK RK, AND PIPING AND RK, - OFFS ” BY SHALL UNITS CONTINUE ROOFTOP SHALLAND RUN TO SHUT DOWN KITCHEN FROM ALARM FIRE EXHAUSTUPON HOOD EXTINGUISHIN EITHER ENERGIZEDEXHAUST WHEN IS FAN ENERGIZED. INTERLOCK RTU INTERLOCK EQUIPMENT AND CONTROL FOR DATA INFORMAFAN KITCHEN TO AREA. REFER KITCHEN EQUIPMENT SUPPLIER MAKE KITCHEN SHALLFANS BE COOK INTERLOCKED OPERATE WITH TO COORDINATE INSTALLATION ELECTRICAL WITH CONTRACTOR. KITCHENMASTER VENTILATION PANEL CONTROL AS INDICATED THEIR ASSOCIATED COOKING EXHAUST OR EQUIPMENT OR HOODS KITCHEN EXHAUST SHALL FANS ON BE ENERGIZED THROUGH C. OPERATION.OF SEQUENCE UNIT REFER THETO ROOFTOP MATRIX CONTROL M3.1SHEET ON B. ALL SET POINTS, TIME DELAYS, SHALLETC. BE ADJUSTAB UNITTO THERMOSTAT. PROGRAMMED AND OWNER OCCUPIED/UNOCCUPIED OPERATIONSCHEDULE OF SHALL DEBE A. OPERATIONOF SEQUENCE • • • • M4.12. WIRING MECHANICAL ON DIAGRAMS S LOCATED HOOD REFERENCE INTERLOCK AND CONTROL DIVISION WITH REQUIREMENTS FOR 2 COORDINATE KITCHEN EXHAUST DIAGRAMS WIRING AND I HOOD DURING THIS PERIOD ADDITIONAL AT NO TO OWNER.COST THE THEOF SYSTEM BY THE ARCHITECT/ENGINEER. DE CORRECT SHALLA PERIOD BE FOR YEAR GUARANTEED OF T ONE FOLLOWING THAT INSTALLATION REQUIREMENTS THE OF MEETS SPECIFIC PROVIDE SUPERVISION ON AND CONTROLLER. THE ASSOCIATED CONTROL DROP THE WITH DISTANCE BETWEEN SHALL WIRING EQUIPMENT. CONTROL BE SIZED ACCOMMODA TO INSTALLED FURNISHED WIRING ANDEQUIPMENT PACKAGE WITH INTERCONNECTIONSINTEGRATED BETWE DIAGRAMS WIRING SHOWING RELAYS PROVIDETO REQUIRED DESIRED THE OPEOF SEQUENCE PANELS, CONTROL TIME OVERRIDE TIMERS,SWITCHES, DAMP PROVIDE A INCLUDINGSYSTEM CONTROLS TEMPERATURE OF THE SET POINT (75°F). SYSTEM SHALL BE ACTIVATED BY MAINTAINTO THERMOSTAT H. SET POINTTEMPERATURE (90°F). EXHAUST FAN SHALL BE ACTIVATED TO THERMOSTAT M BY ROOM G. MODE. DURING ENERGIZE SHUT DOWN FAN AND DURING MODE OCCUPIED BREAKER IN "SMART" DURING HOURS. UNOCCUPIED PANELB DOWN OPERATE EXHAUST CONTINUOUSLY FANS DURING OCCUPIED HOU F. EQUIPMENT SERVED. EXHAUST FAN SHALL BE INTERLOCKED TURN TO E. DISCHARGE AIR OF TEMPERATURE 70°F (ADJUSTABLE). 80°FOF TEMPERATURE HEATING AND SHALL P TO MODULATE COOLING SHALL ENERGIZE AS REQUIRED PROVIDETO MAXIMUM DIS ISTHE OUTSIDEMUA AIRSHALLOFF. CLOSE DAMPER WHEN MUA.OF DETECTOR SMOKE MOUNTED DUCT FROM ALARM UPON FIREHOOD EXTINGUISHING SYSTEM, UNIT ROOFTOP DETE SMOKE MAKE OPERATION. OF MODULATION SEQUENCE FOR PANEL. TOCONTROL REFER INSTALLATION, OPERATION, MA AND EXHAUST FANSMAKE AND AIR SHALLEXHAUST OPEN 100% DAMPER KEFFANS WHEN MAKE AIR SHALLEXHAUST OPEN 100% DAMPER KEFFANS WHEN MAKE D. - - - - UP UNITUP SUPPLY AIR FAN SHALL BE DE AIRUP (MUA AIRUP (MUA AIR,UP OTHER AIR AND DIVISION 23 WIRING. CONTROL SHALL VOLTAGE PROVIDE LOW INTERLOCK FOR WIRING MECHANICAL SYSTEMS. DIVISION SHALL 26 CONTRACTOR PROVIDE LINE VOLTAGE CONTR DIVISION SHALL 26 CONTRACTOR PROVIDE LINE VOLTAGE WIRIN SPLIT SYSTEM UNIT (FC ELECTRICAL EXHAUST (EF FAN CONTROL EXHAUST (EFRESTROOM/JANITOR FAN CONTROL EXHAUST (KEF FAN DISHWASHER CONTROL MAKE KITCHEN EXHAUST (KEF CONTROL FAN UNIT ROOFTOP (RTU CONTROL GENERAL CONTROL - UP AIRUP UNIT (MUA CONTROL - 4, 5, 10, 11, AND 12 KEFWITH - - 2) 2) UNIT SUPPLY AIR FAN SHALL BE ENERGIZED THE O AND 1) UNIT SUPPLY AIR FAN SHALL BE ENERGIZED THE O AND - UP AIRUP UNITS SHALL THRU HOOD THE MODULATE - HANDLING EQUIPMENT PROVIDING FRESH AIR THETO - - 1 / CU JOB CHECKOUT SERVICE CHECKOUT AS ENSURE TO REQUIRED JOB - 1) - 1 - 1 3) - 1, 2) - ENERGIZED BY ANY KITCHEN EXHAUST - 1 - 1 - 5 SO THE UNITS SUPPLY AIR IS FAN - - 5) ‘ 3) ON - 6) ’ AND - LE. 1, 2) ‘ ’ - - OFF S DRAWINGS OR OR S DRAWINGS 3, 4, 5 ARE ENERGIZED. 1 & 2 ARE ENERGIZED. ROOM THERMOSTAT THERMOSTAT ROOM FECTS OCCURRING FECTS OCCURRING - ROVIDE MINIMUM ATION. SYSTEMTHE ER MOTORS, AND AND MOTORS, ER OFF SWITCHES ATOFF SWITCHES ’ ON THE DRAWINGS. THE ON DRAWINGS. WITH THE WITH TION. HVAC THE NSTALLATION 6 CONTRACTOR. 6 CONTRACTOR. INTENANCE MANUAL TE VOLTAGE THE AND M3.2 AND FOR ING APPLIANCES, TERMINED BY G SYSTEM,G KEF RATION. PROVIDE AINTAIN ROOM CTOR ALARM, OR OR ALARM, CTOR DEVICE AND THE RMOSTATS, RMOSTATS, SHUT AND RS . HEETS M4.1HEETS TO OARD THROUGH A THROUGH HE ACCEPTANCE ACCEPTANCE HE UNOCCUPIED UNOCCUPIED CHARGE AIR CHARGE G. EN FIELDEN OL AND OL AND UTSIDE UTSIDE - - 1 - 5 T. COORDINATE WITH MANUFACTURER COORDINATE WITH TO PROVIDE A TAG FRO DAVE & BUSTER'S DIVISIONT. 23 SHALL CONTRACTOR PERF LANDLORDS. SHALL PROVIDE FACTORY START-UP OF UNITS DAVE & BUSTER'S DIVISIONR. 23 CONTRACTOR SHALL CLEA COOLINGP. COIL MBH VALUES DO INCLUDE NOT FAN HEAT. N. ABS. MIN. O/A IS THE ABSOLUTE MINIMUM OUTSIDE AIR M. LANDLORD SHALL PROVIDE GUARDS PROTECT TO CONDENSE L. SCHEDULED IS WEIGHT THE MAXIMUM ALLOWABLE OPERATI K. LANDLORDJ. SHALL PROVIDE STANDARD INSULATED ROOF CU H. SPECIFIED FAN ESP ACCOUNTS FOR LOSSESDUCT EXTERN LANDLORD SHALL PROVIDE DUPLEXG. RECEPTACLE MOUNTED STARTERS FOR ALLF. MOTORS SHALL BE FURNISHED INTEGR LANDLORDE. SHALL PROVIDE FACTORY MOUNTED DISCONNECT LANDLORDD. SHALL PROVIDE 2 INCH MERV 8, EFFICIENT P EQUIPMENT SIZED FOR C. 95°F AMBIENT TEMPERATURE. REFER ROOFTOPTO UNIT CONTROLB. MATRIX FOR CONTROL A. NOTES: MODEL NUMBERS SHALL BE NOT CONSIDERED COMPLETE AND T-2ACD ENXLNO G204 08000575244.7 244.7 7.5 244.7 7.5 0.5 7.5 0.5 8,000 0.5 8,000 20 8,000 20 LGH240H4B 20 LGH240H4B LENNOX LGH240H4B LENNOX LENNOX LENNOX LENNOX LENNOX ARCADE ARCADE ARCADE RTU-12 RTU-11 RTU-10 T- O ENXLNO G044 ,0 .5206. 517 55.1 67.4 26 2.0 26 2.0 0.5 0.75 0.75 0.5 0.75 0.75 2,400 2,200 1,100 1,100 6 6 3 3 LGH074H4T 23 LGH074H4T LGH036H4E 2.0 3 1. 5.0 LGH036H4E 0.75 0.75 LENNOX LENNOX 10,000 LENNOX 0.75 3,200 LENNOX 4,800 25 6,000 3,00 LENNOX 10 15 LENNOX LENNOX LGH300H4B 20 7.5 LENNOX LGH120H4B LGH180H4B LGH240H4B LENNOX LGH092H4B LENNOX LENNOX LENNOX WIN/ZOO/TECH LENNOX FUNCTION 2 LENNOX BOH FUNCTION 1 LENNOX LENNOX LENNOX LENNOX RTU-9 COOK/PREP LINES RTU-8 RTU-7 SPORTS DINING PICKUP/DRY STORAGE FLEX DINING RTU-6 BAR/ENTRY RTU-5 RTU-4 RTU-3 RTU-2 RTU-1 AKSRIEMNFCUE OE NOMINAL MODEL MANUFACTURER SERVICE MARK MINIMUM EFFICIENCY SCHEDULED. LANDLORD SHALL PROVIDE HEATER MEETTO OR EXCEED SCH LOCATION EXISTING ROOFTOP UNIT SCHEDULE (DX COOLING, NATURAL CFM USING VENTILATION RESET DEMANDOR CONTROL VENT EQUIPMENT ACCESSORIES AND CONTROL MODULES PROGRAMMED CONTROL FEATURES SETPOINTS NOTES: CONTROL PANEL(S), THERMOSTAT(S),WIRING, TEMPERATUR SAFETIES, INTERLOCKS, AND ALARMS SUPPLY FAN CONTROL METHODS REQUIREMENTS. CONTROL MATRIX. EACH UNIT SHALL CONTROL BASED ON IT W. M. LEATED THROWAWAY AIR FILTERS.LEATED THROWAWAY Q. G. N. H. Y. S. K. E. B. X. Z. F. T. .DIVISION 28 INTERLOCKTO FACP WITH RTU FOR SHUTDO J. N N THE UNIT AND PROVIDE SET OF A NEW FILTERS AT EACH ORM AND BALANCETEST OF THE HVAC SYSTEM PER SPECIFI MATERIAL SHALL BE NOT ORDERED BY MANUFACTURER AND M AND SHALL BALANCE UNITS AFTERIS TENANT DUCTWORK IN AL WITH ALUNIT. WITH AL UNIT.TO ECONOMIZER FAULT DETECTION AND DIAGNOSTICS (FDD) SY INTEGRATED ECONOMIZER - DIFFERENTIAL ENTHALPY ENABL OUTSIDE AIR DAMPER - MOTOR OPERATED (MODULATING) DEMAND CONTROL VENTILATION - CO2 SENSOR FEEDBACK REMOTE TEMPERATURE SENSOR HVAC SYSTEM OCCUPIED/UNOCCUPIED MODE - PROGRAMMABLE DEHUMIDIFICATION SETPOINT - HUMIDITY SENSOR FEEDBAC HEATING - UNOCCUPIED SETPOINT HEATING - OCCUPIED SETPOINT DEAD BAND - MINIMUM HEATING AND COOLING TEMPERATURE COOLING - UNOCCUPIED SETPOINT COOLING - OCCUPIED SETPOINT LANDLORD SHALL PROVIDE LENNOX MOUNTED WALL CO2 SENS LANDLORD SHALL PROVIDE LENNOX DUCT MOUNTED HUMIDITY LANDLORD SHALL PROVIDE REMOTE TEMPERATURE SENSOR (H DURING OPTIMUM START SEQUENCE, THE SHALLUNIT SUPPL DAVE & BUSTER'S DIVISION 23/26 CONTRACTOR SHALL INT DETERMINE MINIMUM DAMPER POSITION IN FIELD DURING B FAULTSTHE FOLLOWING SHALL BE DETECTED: AIR TEMPERA COMPRESSOR, HEATING, MIXED LIMIT AIR LOW ALARM, AN DEVICE SHALL BE FACTORY MOUNTED AND PRE-WIRED FOR O RETURN AIR HUMIDITY; LANDLORD PROVIDED AS PART OUTSIDE AIR HUMIDITY; LANDLORD PROVIDED AS PAR RETURN AIR TEMPERATURE; LANDLORD PROVIDED AS P OUTSIDE AIR TEMPERATURE; LANDLORD PROVIDED AS IF SETPOINT VALUE IS LISTED, IT INDICATES ECONOMIZE DAVE & BUSTER'S DIVISION 28 CONTRACTOR SHALL PROVID KITCHEN EXHAUST SYSTEM INTERLOCK FIRE ALARM CONTROL PANEL - SAFETY INTERLOC SHUTDOWN LIMITLOW FREEZESTAT - FREEZE PROTECTION SAFETY SHU RETURN AIR SMOKE DETECTOR - SAFETY SHUTDOWN VALVEGAS SAFETY VARIABLE VOLUME - STAGED FAN CONTROL IN RESPONSE TO CONSTANT VOLUME FAN CONTROL OPTIMUM START SEQUENCE CYCLE LOADS WITH DURING UNOCCUPIED HOURS ON DURING OCCUPIED HOURS HEATING COIL (NATURAL GAS) DEHUMIDIFICATION - HOT GAS REHEAT COOLING COIL (DX - STAGED) RELIEF - CONSTANT VOLUME EXHAUST POWERED FAN RELIEF - BAROMETRIC DAMPER LANDLORD SHALL PROVIDE PROGRAMMABLE HONEYWELL VISIO PROGRAM DEHUMIDIFICATION SEQUENCE BASED ON RETURN A UNITARY CONTROLLER SHALL MODULATE AND/OR CYCLE SUPP EXHAUSTPOWERED FAN SHALL STAGE ON AND OFF ACCORDIN PROVIDE STAGED FANMINIMUM CONTROL WITH 2 FAN SPEED ANPROVIDE FDD UNIT SYSTEMWITH CONSISTING OF PERMA FEATURES, MODULES, AND ACCESSORIES THAT SHALL BE PR NG WEIGHT OFNG THE WEIGHT EQUIPMENT AND CURB. RB WITH MINIMUMRB WITH HEIGHT OF18 INCHES. PROVIDE SLOPED M THE FACTORY MATCHTO THE "MARK" COLUMN OF THIS SC ON UNIT FOR FIELD WIRING. R COIL FROM HAIL OR OTHER DAMAGE. INSTALLED ON SERVICE SIDE OF UNIT. EDULED MINIMUM MBH NOMINALOUTPUT. INPUT IS BASED O ONG CFM TONNAGE SUPPLY FAN ESP (IN) CONTROL FEATURE . . 537. 616. 175. -1A1. 3027. 1 71.4 2 13.0 12.5 R-410A 50.1 51.7 60.8 76.1 76.8 85.3 2.0 1.0 0 NOM HP . 7. 6. 506. 954. -1A1. 2522603 216.0 2 12.5 11.6 R-410A 49.2 49.5 60.1 75.0 267.6 278.6 7.5 0 S OWN INTERNAL S SAFETIES,OWN TIME DELAYS, AND SEQUENCES E E SENSOR(S),HUMIDISTAT(S), AND/OR CO2 SENSOR(S) WHE LOCATION IN THE ONUNIT DAY OF SUBSTANTIAL COMPLET R HIGH-LIMIT SHUTOFF. UNIT SHALL BE IN ECONOMIZER I ILATION. T T OF ECONOMIZER CONTROL MODULE. WN UPON ACTIVATIONWN OF ANSUL SYSTEM, SMOKE DETECTORS ECONOMIZEROF CONTROL MODULE. ERLOCK RTU WITH KITCHENERLOCK EXHAUST RTU WITH FAN ENERGIZETO WHE PART OFPART ECONOMIZER CONTROL MODULE. CATIONS. (Y/N) D SENSORD VALUES. EACH OPERATING MODE SHALL BE CAPAB VFD ART ART OF ECONOMIZER CONTROL MODULE. STALLED. DAVE & BUSTER'S DIVISION 23 CONTRACTOR TO ALANCING PROVIDETO SCHEDULED DURIN OUTDOOR AIRFLOW E E DEVICE. REFERENCE DAVE & BUSTER'S FIRE PROTECTION CURB IF NEEDED MATCHTO ROOF SLOPE. TDOWN K 01601477. 795. 58R40 201. 9. 260 198.0 2 13.5 12.0 R-410A 55.8 56.1 67.9 79.8 114.7 176.0 .0 NENTLY INSTALLED OUTSIDE AIR, SUPPLY AIR, AND RETUR STEM TURE SENSORTURE FAILURE, ECONOMIZER ENABLED/DISABLED WH OVIDED WITH THE OVIDEDEQUIPMENT. WITH Y THE LESSER OF THE MINIMUM OFRATE OUTDOOR AIR OR E (OA ENTHALPY < RA ENTHALPY) ODEL NUMBERS ONLY. REVIEW THE COMPLETE DESCRIPTION ACTIVE COOLING COIL STAGES HEDULE. FOR EXAMPLE, EACH SHALLRTU READ THE RTU-# S. LOW SPEEDS. SHALLLOW EXCEED NOT 66% FULLOF SPEED AN PERATION SUBJECT THE TO ONBOARD CONTROLLER. K SETPOINT DIFFERENCE N LISTEDN MANUFACTURER'S STANDARD PRODUCT. COORDINAT SENSOR. PROVIDE 18 GAUGE SHIELDED PAIR LOWTWISTED LY FAN SPEED SETTING AND COIL CAPACITY STAGES SUBJE G TO DAMPERTO G POSITION. OR. PROVIDE PROVIDE 18 GAUGE SHIELDED PAIR TWISTED IR HUMIDITY. ONEYWELL BLANKTR21 WITH FACE). PROVIDE 18 GAUGE TW NPRO MODEL 8000 THERMOSTAT WIFI (NOT INCLUDING WITH THERMOSTAT MH MH ° B ° B ° B (°F WB) (°F DB) (°F WB) (°F DB) (MBH) (MBH) 0. 048. 805. 55R40 201. 3. 8. 5 180.0 132.0 2 13.0 12.0 R-410A 55.5 57.3 68.0 80.0 70.4 104.1 135. 636. 115. -1A1. 6025. 0066.5 70.0 55.8 2 16.0 12.0 R-410A 51.1 51.1 62.2 76.3 56.1 61.3 HS A LAT EAT SH TH . 6. 016. 345. -1A1. 32228830051 360.0 248.8 2 13.2 12.0 R-410A 53.4 53.4 67.1 80.1 162.5 6.1 31. 796. 655. -1A1. 70(ER 7065. 65. 37.0 37.0 2 2 17.0 (SEER) 17.0 (SEER) 12.5 12.5 R-410A R-410A 56.3 56.3 56.5 56.5 66.9 66.9 77.9 77.9 19.8 19.8 .3 .3 9. 956. 575. -1A1. 3223184005. 9 9 52.8 9 52.8 52.8 480.0 480.0 480.0 321.8 321.8 321.8 2 2 2 13.2 13.2 13.2 12.0 12.0 R-410A 12.0 R-410A 55.7 R-410A 55.7 55.7 55.7 55.7 66.1 55.7 66.1 79.5 66.1 79.5 197.8 79.5 197.8 197.8 . 375. 33R40 201. 511806. 792200 2 97.9 64.9 108.0 65.1 2 16.0 12.0 R-410A 53.3 53.3 63.7 6.9 EXISTING ROOFTOP UNIT CONTROL MATRIX COOLING COIL F CONDITIONS ARE LESS SETPOINT. THAN THE FOLLOWING RE SHOWN ON RE THE DRAWINGS SHOWN AND AS REQUIRED FACILITTO ION. UNLESS FINA NOTEDOWNER COORDINATEOTHERWISE. WITH COORDINATE WITH LANDLORDCOORDINATE WITH IN SUFFICIENT AMOUNT OF T UNITS H5%5%5%NNN5%5%N5%5%5%DV2 I 3Y DIV 23 DIV 23 50% 50% 50% N 50% 50% N N N 50% 50% 50% % RH P ,0 ,0 ,0 ,0 ,0 I 3DV2 Z DIV 23 DIV 23 N N N N 1,000 1,000 N N N 1,000 1,000 1,000 PPM N AIR TEMPERATURE SENSORS. THE UNIT CONTROLLER SHAL FLOOR PLAN FOR SMOKE REQUIREMENTS.DECTECTOR F6 06 06 06 06 06 0------60 -- 70 80 60 75 70 80 60 75 70 80 60 75 70 80 60 75 70 80 60 75 70 80 60 75 70 80 60 75 70 80 60 75 70 80 60 75 70 80 60 75 70 80 60 75 70 80 °F 75 °F °F °F F555555555555- -- -- 5 5 5 5 5 5 5 5 5 5 5 5 °F , PULL STATIONS, ETC. PER SEQUENCE OF OPERATION ON N N HOOD SYSTEM IS ENERGIZED FOR PRESSURIZATION. LE INDEPENDENTLYOF OPERATING FOR TESTING. THE SYST REFR ON THE FACTORY TAGS FACILITATETO COORDINATION ONSI TYPE D SHALL D NO MORE DRAW THAN 40% OF AT FULL FAN POWER SUPPLY 3 COMPLETE AIR CHANGES DURING THE 1-HOUR PER LOW VOLTAGE PER WIRING LOW MANUFACTURER'S RECOMMENDATIO CT TO THE INTERNALCT TO SAFETIES AND SEQUENCES MAINTATO G G OCCUPIED HOURS. DAMPER SHALL BE CLOSED DURING UN VOLTAGE PER WIRING MANUFACTURER'S RECOMMENDATIONS. , NOTES AND SPECIFICATIONS DETERMINETO THE EXACT M EN ECONOMIZER SHOULD BE OFF/ON, RESPECTIVELY, DAMPE ISTED PAIR, SHIELDED VOLTAGE PER LOW WIRING MANUFAC REDLINK) (MODEL# TH8321WF). PROVIDE 18 V GAUGE LOW E E EQUIPMENT GAS DAVE LOAD WITH & BUSTER'S PLUMBING EPITSTON EPITSTON EPITSTON SET SETPOINT SETPOINT SETPOINT SETPOINT SETPOINT SETPOINT NT )(OEL NT )YYY(OEL NT )YYYYFACT Y Y Y Y (NOTE L) (NOTE L) Y Y Y (NOTE L) (NOTE L) (NOTE L) OR Y/N OR Y/N OR Y/N OR Y/N OR Y/N OR Y/N OR Y/N OR Y/N OR OR Y/N OR Y/N OR Y/N OR Y/N OR Y/N OR Y/N OR Y/N OR Y/N OR T- T- T- T- T- T- T- T- T- RTU-10 RTU-9 RTU-8 RTU-7 RTU-6 RTU-5 RTU-4 RTU-3 RTU-2 RTU-1 ER IE)SAE MH MH ° B ° B TGSCMO CFM STAGES (°F DB) (°F DB) (MBH) (MBH) STAGES (IEER) (EER) I 32 I 32 S M, Q DIV 23/26 DIV 23/26 -- Y -- Y N Y H N N FACTORY FACTORY N N N Y N N Y N N Y Y N N Y N N N N N N N N N Y N Y N N N N I 3DV2 W DIV 23 DIV 23 Y Y Y Y Y Y Y Y Y Y Y Y ATR ATR F, G E FACTORY FACTORY FACTORY FACTORY Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y I 3DV2 X DIV 23 DIV 23 Y Y Y Y Y Y N Y Y Y Y Y I 8DV2 J DIV 28 F FACTORY DIV 28 FACTORY Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y I 8DV2 B T DIV 28 F -- FACTORY -- DIV 28 -- FACTORY -- Y -- Y -- -- M -- N Y Y M Y FACTORY Y FACTORY Y FACTORY FACTORY Y Y FACTORY Y Y FACTORY Y FACTORY Y Y Y Y FACTORY Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y N Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y N N Y Y Y Y Y Y Y Y N Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y I F I OMNOTNMIPTETLTMNN / MIN O/A MIN NO LAT EAT NOM INPUT MIN OUT MIN NO MIN EFF GAS HEAT) (U.N.O.) (NO SUBSTITUTIONS) SENSORS SHALL DETERMINE ECONOMIZER ON POINT. ATE THE SCHEDULED CONTROL MODULES AND SEQUENCES OF IME DELAYNOT TO CONSTRUCTION. L BUILDING AND EQUIPMENT SCHEDULES DURING STARTUP. FA1.0. L AAT MINIMUM BE CAPABLE OF PROVIDING SYSTEM STATU EM SHALL REPORT FAULTS ANTO APPLICATION ACCESSIBL TE. SPEED. IOD BEFORE NORMAL OCCUPIED MODE. OLTAGE WIRING OLTAGEPER WIRING MANUFACTURER'S RECOMMENDATIONS. ATERIAL AND ACCESSORIES BETO ORDERED. IN IN SCHEDULED SETPOINTS. OCCUPIED HOURS. TURER'S RECOMMENDATION. R MODULATING, NOT AND EXCESS OUTSIDE AIR. CONTRACTOR IFCONTRACTOR DIFFERENT FROM SCHEDULED.THAT MEET 60.0 70.0 96.5 2 0 -- 480/3 65 70 NON-FUSED 3,600 A A - L, N-T 3,600 NON-FUSED 70 65 480/3 -- 0 2 96.5 70.0 60.0 30.0 68.0 99.9 2 100 -- 480/3 20 25 NON-FUSED 1,350 A A - L, N-T 1,350 NON-FUSED 25 20 480/3 -- 100 2 99.9 68.0 30.0 HEAT HEAT EXCHANGER NS. 0 58.9 102.4 1 200 100 480/3 12 15 NON-FUSED 800 A A - L, M, N-T A - L, M, N-T 800 800 NON-FUSED NON-FUSED 15 15 12 12 480/3 480/3 100 100 200 200 1 1 102.4 102.4 58.9 58.9 0 0 .0 51.8 91.7 2 1,425 700 480/3 31 35 NON-FUSED 2,500 A A - L, M, 2,500 NON-FUSED 35 31 480/3 700 1,425 2 91.7 51.8 .0 1.8 93.3 2 950 600 480/3 24 30 NON-FUSED 1,400 A A - L, M, N-T 1,400 NON-FUSED 30 24 480/3 600 950 2 93.3 1.8 .6 95.8 2 1,800 900 480/3 43 50 NON-FUSED 2,750 A A - L, M, N-T 2,750 NON-FUSED 50 43 480/3 900 1,800 2 95.8 .6 ON EPITSTON EPITSTON EPITFURNIS SETPOINT SETPOINT SETPOINT SETPOINT SETPOINT POINT 90.0 2 125 -- 480/3 16 20 NON-FUSED 950 A A - L, N-T 950 NON-FUSED 20 16 480/3 -- 125 2 90.0 7.0 2 2,250 -- 480/3 47 50 NON-FUSED 2,800 A A - L, N-T A - L, N-T 2,800 A - L, N-T 2,800 NON-FUSED 2,800 NON-FUSED NON-FUSED 50 50 50 47 47 480/3 47 480/3 -- 480/3 -- 2,250 -- 2,250 2,250 2 2 2 7.0 7.0 7.0 RESPONSIBILITY FOR ALL THE FANS.FORALL THE RESPONSIBILITY WARRANTEE THE CARRIES SUB THE THAT SUCHHIGGIN'S) (JDVENDOR THE WITH COORDINATE VENDOR. OWNERS THE HOODS BY FURNISHED ALLMAKE EXHAUST INSTALL FANS, CO.).HIGGINS (JDVENDOR D&B COORDINATECURBWITH HEIGHT PROPER GREATER. IS WHICHEVER 10 FEET, BUILDING STRUCTUREWITHIN HIGHER THAN ADJACENT ELEVATION ORAT SURFACE ROOFMINIMUM 40" FANS HEIGHT ABOVE DISCHARGE ROOFCURBEXHAUST EXTENSIONINSTALL FORGREASE ANDSPECIFICATIONS.SCHEDULES EXHAUSTMAKE FAN, FAX 817 (800CO. HIGGINS JD AT CONTACTLAPINSKI AL SCHEDULES, AND RELIEF AIR HOOD SCHEDULES. AIR AND SCHEDULES, RELIEF MAKESCHEDULES, FANS SCHEDULES, M4.8 & M4.4, M4.1, TO FOR EXHAUSTREFER HOOD CLARIFICATION. FOR ATTENTION ARCHITECT'S BROUGHTTO BE SHALL DISCREPANCIES ANY OTHERWISE. NOTEDUNLESS SHOWN CONTRACTORALL WORK GENERAL PROVIDE TO I ABS MIN / RYNO / RYNB HL BY SHELL BY SHELL Y/N OR Y/N OR Y/N OR Y/N WITH ALL DISCIPLINESWITH OTHER AND EXISTING CONDITIONS FINAL AND DEMO BIDS. WORK CAREFULLY COORDINATE NEW FIELD VERIFY ALL EXISTING CONDITIONS PRIOR TO SUBMI SITE VISITS MAY AND REFLECT NOT EXACT "AS EXISTING ORIGINAL FROM TAKEN CONDITIONS DRAWIN WERE NOTE: -- 480/3 16 20 NON-FUSED 950 A A - L, N-T 950 NON-FUSED 20 16 480/3 -- /A - REFERENCE DIVISION SPECIFICATIONS FOR INDIVIDUAL DE 548 OPERATION SHALL BE FURNISHED AND INSTALLED PER ROOF S OF ECONOMIZER, E E BY SERVICE PERSONNEL. V/PH - 1829)FORINFORMATION REGARDING THE MI NIM UM T-1RU1 EPNSBLT NOTES SIBILITY RESPON RTU-12 RTU-11 C MOCP MCA LCRCLWEIGHT ELECTRICAL - UP AIR UNITS, ANDHOOD UNITS, AIR UP TYPE IC(LBS) DISC - R ATR K FACTORY ORY UP AIR UNITS, AND UNITS, AIR UP E INSTALLED HED - UP AIR UNIT AIR UP - BUILT" CONDITIONS. - VICE 772 TOP UNIT NOTES TTING - . 5452, N-T GS & GS LITION 60/990% 06/06/19 ISSUE FOR0 06/17/19 ADD. #1 07/26/19 1 2 Drawing TitleDrawing O AEREMARKS DATE NO. Sheet Sheet No. Scale No.Job COPYRIGHT FIELD VERIFICATION ARIAGROUPARCHITECTS, INC. Aria Group Architects, Inc. shall retain all all retain shall Inc. Architects, Group Aria Group Architects, Inc. Architects, Group Aria of consent written without otherwise or disclosed duplicated, be not shall documents related and drawings These rights. reserved other and statutory law, common these drawings. these scale not Do work. any fabricating or beginning before discrepancies or omissions errors, dimensional any of Inc. Architects, Group Aria notify and site job the at conditions and dimensions figured all verify shall Contractor 830 North Blvd. North 830 184150 SCHEDULES& 708-445-8400 MECHANICAL M3.1 ariainc.com GOR PU Oak Park, Park, Oak REVISIONS NOTES Illinois 8345 LENEXA DRIVE, SUITE 300 60301 LENEXA, KS 66214 TEL 913.742.5000FAX 913.742.5001 Date Drawn REVIEW PERMIT WWW.HENDERSONENGINEERS.COM 06/06/2019

Author 1950001061 1471 MACARTHUR ROAD WHITEHALL, PA 18052 G R O U P

AIR BALANCE SCHEDULE UNIT HEATER SCHEDULE (ELECTRIC) MECHANICAL SYMBOLS 830 North Blvd. EXHAUST: SERVES EXHAUST CFM WHEN EXHAUST CFM AT MARK SERVICE MANUFACTURER MODEL NOM MOUNTING MIN NO CFM V/PH DISC NOTES Oak Park, ONLY KIT. IN OCC. MODE BLDG OCC. MODE LOCATION (KW) TYPE OF STAGES TYPE THIS IS A MASTER LEGEND AND NOT ALL SYMBOLS OR ABBREVIATIONS ARE USED. Illinois KEF-1 HOOD#1 COOKING HOOD 1,900 1,900 EUH-1 SPRINKLER ROOM QMARK LFK4883F 4.8 SURFACE 1 100 208/3 NON-FUSED A-D STANDARD MOUNTING HEIGHT HVAC DUCTWORK AND ACCESSORIES KEF-2 HOOD#2 COOKING HOOD 1,312 1,312 60301 KEF-3 HOOD#3 COOKING HOOD 1,983 1,983 MODEL NUMBERS SHALL NOT BE CONSIDERED COMPLETE AND MATERIAL SHALL NOT BE ORDERED BY MANUFACTURER THERMOSTATS (USER ADJUSTABLE)(TOP OF DEVICE) 48" LINEAR SLOT DIFFUSER KEF-4 HOOD#4 COOKING HOOD 3,408 3,408 AND MODEL NUMBERS ONLY. REVIEW THE COMPLETE DESCRIPTION, NOTES AND SPECIFICATIONS TO DETERMINE THE CONTROLS (TOP OF DEVICE) 48" 708-445-8400 KEF-5 HOOD#5 COOKING HOOD 2,083 2,083 EXACT MATERIAL AND ACCESSORIES TO BE ORDERED. THE MANUFACTURERS LISTED ARE THE BASIS FOR THE DESIGN. KEF-7 DISHWASHER DISHWASHER -- 600 INSULATED FLEXIBLE DUCT (MAX. 5' -0" LONG) ariainc.com EF-1 RESTROOMS EMPLOYEE RESTROOM/JANITOR -- 275 NOTES: USE THE DEFAULT MOUNTING HEIGHTS SHOWN ABOVE UNLESS NOTED ARIA GROUP ARCHITECTS, INC. EF-2 BACK OF HOUSE PUBLIC RESTROOM/REAR JANITOR -- 1,900 OTHERWISE IN THE SPECIFICATIONS OR ELSEWHERE. MOUNTING HEIGHTS BRANCH DUCT WITH 45° RECTANGLE -ROUND EF-3 ELECTRICAL ELECTRICAL 3,000 3,000 A. PROVIDE INTEGRAL FAN SWITCH AND QMARK M602W WALL MOUNTED THERMOSTAT. LISTED ARE ABOVE FINISHED FLOOR (AFF) OR ABOVE FINISHED GRADE (AFG) TO TOP OF DEVICE. ALL DEVICES SHALL BE INSTALLED IN COMPLIANCE WITH BRANCH FITTING AND MANUAL VOLUME DAMPER B. PROVIDE CORROSION RESISTANT HEAVY-DUTY FACE GRILLE. CURRENT ADA AND LOCAL REQUIREMENTS. TOTAL... TOTALS: 13,686 16,461 C. PROVIDE SURFACE MOUNT WALL BRACKET. ELBOW WITH TURNING VANES MAKEUP AIR: TON SUPPLY AIR SERVES MAX PERCENT MIN O.A. MIN. O.A. D. PROVIDE FACTORY MOUNTED DISCONNECT INSTALLED ON SERVICE SIDE OF UNIT. ANNOTATION (CFM) OA (CFM) OA/SA ONLY KITCHEN CFM IN OCCUPIED MODE 1 MECHANICAL PLAN NOTE CALLOUT BRANCH DUCT WITH BELL -MOUTH FITTING & RTU-1 20 6,000 BAR/ENTRY 1,800 30% -- 900 MANUAL VOLUME CONTROL DAMPER RTU-2 10 3,200 FLEX DINING 950 30% -- 600 RTU-3 15 4,800 SPORTS DINING 1,425 30% -- 700

CU MECHANICAL EQUIPMENT DESIGNATION (CONTRACTOR FAX RTU-4 7.5 2,400 PICKUP/DRY STORAGE 100 4% 100 100 1 FURNISHED AND INSTALLED UNLESS NOTED OTHERWISE) RETURN, EXHAUST, OR OUTSIDE AIR DUCT UP RTU-5 25 10,000 COOK/PREP LINES 0 0% 0 0 1950001061 RTU-6 6 2,400 BOH 200 8% -- 200 CONNECTION POINT OF NEW WORK TO EXISTING RETURN, EXHAUST, OR OUTSIDE AIR DUCT DOWN LENEXA, KS 66214 RTU-7 3 1,100 FUNCTION 1 200 18% -- 100 AIR CURTAIN SCHEDULE

RTU-8 3 1,100 FUNCTION 2 200 18% -- 100 MARK SERVICE AREA MANUFACTURER MODEL UNIT SPECS V/PH/HZ NOTES 913.742.5000 913.742.5001 8345 LENEXA DRIVE,8345 SUITE 300 RTU-9 6 2,200 WIN/ZOO/TECH 125 6% -- 125 LENGTH MAX HEATING MOTOR 1 DETAIL REFERENCE. UPPER NUMBER INDICATES DETAIL SUPPLY AIR DUCT UP TEL WWW.HENDERSONENGINEERS.COM RTU-10 20 8,000 ARCADE 2,250 28% 2,250 2,250 (IN) AIRFLOW CAPACITY (KW) (HP) M1 NUMBER LOWER NUMBER INDICATES SHEET NUMBER RTU-11 20 8,000 ARCADE 2,250 28% 2,250 2,250 AC-1 MAN TRAP MARS NH248-1U 48 2447 N/A 1 480/3/60 A,B,C,D SUPPLY AIR DUCT DOWN RTU-12 20 8,000 ARCADE 2,250 28% 2,250 2,250 1 SECTION CUT DESIGNATION MUA-1 - 2,570 KITCHEN HOODS (1 & 2) 2,570 100% 2,570 2,570 MODEL NUMBERS SHALL NOT BE CONSIDERED COMPLETE AND MATERIAL SHALL NOT BE ORDERED BY MANUFACTURER AND M1 MUA-2 - 5,865 KITCHEN HOODS (3, 4 & 5) 5,865 100% 5,865 5,865 MODEL NUMBERS ONLY. REVIEW THE COMPLETE DESCRIPTION, NOTES AND SPECIFICATIONS TO DETERMINE THE EXACT MATERIAL EQUIPMENT WITH FLEXIBLE DUCT CONNECTION TOTAL: 155.5 ACCESSORIES TO BE ORDERED.THE MANUFACTURERS LISTED ARE THE BASIS FOR THE DESIGN. ABBREVIATIONS

TOTAL OUTSIDE AIR 20,185 15,285 18,010 WHITEHALL, 18052 PA NOTES: A/C AIR CONDITIONING HWP HEATING WATER PUMP 10" (NECK SIZE) ACC AIR COOLED CHILLER IN WC INCHES OF WATER CSD -1 (TYPE) BUILDING PRESSURE AT C02 MAX OA PERCENT 3,724 ACCU AIR COOLED CONDENSING COLUMN 300 CFM (CFM OF SUPPLY DIFFUSER OR REGISTER) POSITIVE AIR FLOW 18% A. MOUNT UNIT PER MANUFACTURER'S RECOMMENDATIONS TO FACE OF WALL AND SUPPORT VERTICALLY. UNIT L LOUVER THE BUILDING PRESSURE CALCULATION FOR "KITCHEN ONLY OCCUPIED B. PROVIDE INTEGRAL STARTER AND DISCONNECT SWITCH. AFC ABOVE FINISHED CEILING LAT LEAVING AIR MODE" IS CALCULATED WHEN PREPARATION IN THE KITCHEN AREA IS BUILDING PRESSURE WHEN ONLY KIT. OCC. 1,599 C. PROVIDE AIR CURTAIN WITH NORMALLY CLOSED DOOR LIMIT SWITCH FOR INSTALLATION ON DOOR. AFF ABOVE FINISHED FLOOR TEMPERATURE 24x24 (NECK SIZE) OCCURING BEFORE STORE BEING OCCUPIED. RTU-4, 5, 10, 11, 12 PERCENT POSITIVE AIR FLOW 10% D. PROVIDE WITH TRANSFORMER AND MANUAL TOGGLE OVERRIDE SWITCH ON UNIT. AFG ABOVE FINISHED GRADE LDB LEAVING DRY BULB CEG -1 (TYPE) AHJ AUTHORITY HAVING LP LOW PRESSURE WILL BE ENERGIZED AT THIS TIME. THE KITCHEN EXHAUST 800 CFM (CFM OF EXHAUST GRILLE) JURISDICTION LWB LEAVING WET BULB HOODS, MUA-1, 2 AND EF-4 ARE TO BE IN OPERATION AT THIS TIME. BUILDING PRESSURE AT MIN OA 1,549 AHU AIR HANDLING UNIT LWT LEAVING WATER IT IS ASSUMED KEF-7 SERVING THE DISHWASH MACHINE WILL NOT BE IN PERCENT POSITIVE AIR FLOW 9% AI ANALOG INPUT TEMPERATURE MANUAL VOLUME DAMPER OPERATION AT THIS TIME. ALL OTHER EQUIPMENT WILL BE ENERGIZED AO ANALOG OUTPUT MAU MAKE -UP AIR UNIT DURING STORE OCCUPIED MODE. AP ACCESS PANEL MAX MAXIMUM APD AIR PRESSURE DROP MBH 1000 BTU PER HOUR SQUARE TO ROUND TRANSITION AWG AMERICAN WIRE GAUGE MD MOTORIZED DAMPER B BOILER MFR MANUFACTURER BAS BUILDING AUTOMATION MIN MINIMUM RD DUCT MOUNTED SMOKE DETECTOR SYSTEM N/A NOT APPLICABLE (SD=SUPPLY/RD=RETURN) BB BACKBONE N/C NORMALLY CLOSED BD BACKDRAFT DAMPER N/O NORMALLY OPEN GRILLE, REGISTER AND DIFFUSER SCHEDULE BD BLOWDOWN NOM NOMINAL # RISER DESIGNATION BFC BELOW FINISHED CEILING NC NOISE CRITERIA MARK MANUFACTURER SERVICE MODEL CONSTRUCTION FACE MOUNTING FACE SIZE NOTES BFF BELOW FINISHED FLOOR NF NON -FUSED TYPE TYPE LOCATION (IN) BFG BELOW FINISHED GRADE NIC NOT IN CONTRACT FD FIRE DAMPER DB AES INDUSTRIES SUPPLY ADB-2 ALL STEEL DROP BOX DUCT MOUNTED 8-SIDED DROP BOX D,P,R BFP BOILER FEED PUMP OA OUTSIDE AIR CSD TITUS SUPPLY OMNI ALL STEEL LOUVERED FACE LAY-IN / SURFACE 24x24 A,B,(C OR D),E,K,L BHP BRAKE HORSEPOWER PICV PRESSURE INDEP. CSD1 TITUS SUPPLY OMNI ALL STEEL LOUVERED FACE LAY-IN / SURFACE 12x12 A,B,(C OR D),E,K,L BI BINARY INPUT CONTROL VALVE FSD FIRE SMOKE DAMPER BO BINARY OUTPUT PROVIDE FURNISH AND INSTALL CSD2 TITUS SUPPLY PAR-AA ALL ALUMINUM PERFORATED FACE LAY-IN / SURFACE 24x24 B,C,E,J BOD BOTTOM OF DUCT QTY QUANTITY CRG TITUS RETURN PAR-AA ALL ALUMINUM PERFORATED FACE LAY-IN / SURFACE 24x24 B,(C OR D),E,H,K BOS BOTTOM OF STRUCTURE RA RETURN AIR SD SMOKE DAMPER CRG1 TITUS RETURN PAR-AA ALL ALUMINUM PERFORATED FACE LAY-IN / SURFACE 12x12 B,(C OR D),E,H,K BTU BRITISH THERMAL UNIT RC ROOM CRITERIA CRG2 TITUS RETURN PAR-AA ALL ALUMINUM PERFORATED FACE LAY-IN / SURFACE 24x12 B,(C OR D),E,H,K CFM CUBIC FEET PER MINUTE RD RETURN DUCT CEG TITUS EXHAUST 50F ALL ALUMINUM EGGCRATE LAY-IN / SURFACE 24x24 B,(C OR D),E,H,K,M CH CHILLER REA RELIEF AIR VD VOLUME DAMPER CLG COOLING RF RETURN FAN CEG1 TITUS EXHAUST 50F ALL ALUMINUM EGGCRATE LAY-IN / SURFACE 12x12 B,(C OR D),E,H,K,M CP CONDENSATE PUMP RFR REFRIGERANT WSR TITUS SUPPLY 300RL ALL STEEL DOUBLE DEFLECTION SURFACE SEE PLANS D,E,F,G,M CPT CONTROL POWER RH RELATIVE HUMIDITY MD MOTORIZED DAMPER WRG TITUS RETURN 350RL ALL STEEL LOUVERED FACE SURFACE SEE PLANS D,E,F,M TRANSFORMER RH ROOF HOOD WEG TITUS EXHAUST 350RL ALL STEEL LOUVERED FACE SURFACE SEE PLANS D,E,F,M CRAC COMPUTER ROOM AIR RPM REVOLUTIONS PER MINUTE CONDITIONING UNIT RTU ROOFTOP UNIT BD BACKDRAFT DAMPER MODEL NUMBERS SHALL NOT BE CONSIDERED COMPLETE AND MATERIAL SHALL NOT BE ORDERED BY MANUFACTURER AND MODEL NUMBERS ONLY. CRU COMPUTER ROOM UNIT SA SUPPLY AIR CT COOLING TOWER SCP STEAM CONDENSATE PUMP REVIEW THE COMPLETE DESCRIPTION, NOTES AND SPECIFICATIONS TO DETERMINE THE EXACT MATERIAL AND ACCESSORIES TO BE ORDERED. THE CV CONTROL VALVE SD SMOKE DUCT DETECTOR MANUFACTURERS LISTED ARE THE BASIS FOR THE DESIGN. CWP CONDENSER SD SUPPLY DUCT NOTES: WATER PUMP SF SUPPLY FAN CU CONDENSING UNIT SH SENSIBLE HEAT CAPACITY A. 4-WAY THROW PATTERN UNLESS OTHERWISE INDICATED BY DIFFUSER SHADED AREA OR FLOW ARROWS ON DRAWINGS. CHWP CHILLED WATER PUMP SOW SCOPE OF WORK B. NECK SIZE SHOWN ON DRAWINGS. PROVIDE BRANCH DUCT TO MATCH NECK SIZE UNLESS OTHERWISE SHOWN ON DRAWINGS. DB DECIBELS SP STATIC PRESSURE DBA DECIBEL AVERAGE ST STEAM TRAP C. BAKED ENAMEL FINISH, WHITE TO MATCH CEILING COLOR (APPLIES TO BACK OF HOUSE / WHITE CEILING AREAS ONLY). DDC DIRECT DIGITAL CONTROL STM STEAM D. FACTORY PRIMED FOR FIELD PAINTING (APPLIES TO FRONT OF HOUSE / AREAS OPEN TO PUBLIC). PAINT TO MATCH WALL. REFER TO ARCHITECTURAL DI DIGITAL INPUT TBD TO BE DETERMINED PLANS. DISC DISCONNECT TC/C TEMPERATURE CONTROLS E. FRAME TYPE TO MATCH CEILING/WALL CONSTRUCTION, COORDINATE WITH ARCHITECTURAL REFLECTED CEILING/WALL PLAN. DN DOWN CONTRACTOR F. FRONT BLADES PARALLEL TO LONG DIMENSION. DS DUCT SILENCER TCP TEMPERATURE CONTROL G. DOUBLE DEFLECTION BARS SHALL BE ADJUSTABLE. DX DIRECT EXPANSION PANEL H. PROVIDE SQUARE TO ROUND NECK ADAPTER BETWEEN DIFFUSER NECK AND BRANCH DUCT AS REQUIRED. (E) EXISTING TF TRANSFER FAN EA EXHAUST AIR TFA TO FLOOR ABOVE J. ALL DUCT DIMENSIONS SHOWN ON DRAWINGS ARE INSIDE DIMENSIONS. PROVIDE BORDER TYPE 1 FOR SURFACE MOUNT. PROVIDE BORDER TYPE 3 FOR LAY-IN MOUNT. EAT ENTERING TFB TO FLOOR BELOW REFER TO DUCTWORK SPECIFICATIONS FOR DUCTWORK INSULATION AND K. PROVIDE WITH RAPID MOUNT FRAMING OPTION FOR LAY-IN TYPE DIFFUSERS INSTALLED IN A HARD CEILING. AIR TEMPERATURE TH TOTAL HEAT CAPACITY LINER INFORMATION. ROOFTOP UNIT CONTROL MATRIX L. CONTRACTOR SHALL PROVIDE REMOTE CABLE-OPERATED VOLUME DAMPER WITH REMOTE WORM GEAR OPERATOR MOUNTED IN TOP OF DIFFUSER ED EXHAUST DUCT TSP TOTAL STATIC PRESSURE CONTROL FEATURE UNITS RTU-13 RESPON SIBILITY NOTES FOR SURFACE MOUNT INSTALLATIONS ONLY. OPERATOR SHALL HAVE A SQUARE DRIVE FOR 1/4" NUT DRIVER. DAMPER ASSEMBLY SHALL INCLUDE EDB ENTERING DRY BULB TT TEMPERATURE

EXHAUST FAN TRANSMITTAL HVAC CONTROL DEVICES ROAD MACARTHUR 1471 SETPOINT FURNISHED INSTALLED GALVANIZED STEEL DUCT WITH ROLLED BEAD STIFFENERS, REINFORCED BLADE, SELF LUBRICATING BEARING AND WORM GEAR MOUNTING PLATE. EF DAMPER SHALL BE INSTALLED IN BRANCH DUCT NOT INLET OF PLENUM DIFFUSER. EFF EFFICIENCY TYP TYPICAL OR Y/N BY BY M. PROVIDE OPPOSED BLADE DAMPER ADJUSTABLE FROM FACE OF DEVICE. EMS ENERGY MANAGEMENT U/F UNDERFLOOR H HUMIDISTAT SETPOINTS SYSTEM U/G UNDERGROUND THE SUPPLY PLENUM. COOLING - OCCUPIED SETPOINT °F 75 -- -- ESP EXTERNAL STATIC U/S UNDERSLAB T THERMOSTAT P. PROVIDE PRE-FABRICATED, 8-SIDED, INSULATED PLENUM WITH WSR GRILLES, AS SCHEDULED. FIELD VERIFICATION COOLING - UNOCCUPIED SETPOINT °F 80 -- -- PRESSURE UH UNIT HEATER R. CONTACT GEORGE LASHER AT 800-786-0402 FOR PRICING AND LEAD TIMES (5-6 WEEKS ESTIMATED). Contractor shall verify all figured dimensions DEAD BAND - MINIMUM HEATING AND COOLING TEMPERATURE SETPOINT DIFFERENCE °F 5 -- -- ETR EXISTING TO REMAIN UNO UNLESS NOTED OTHERWISE SP STATIC PRESSURE SENSOR and conditions at the job site and notify Aria * REFER TO FLOOR PLANS FOR EQUIPMENT AS APPLICABLE. EWB ENTERING WET BULB VAV VARIABLE AIR VOLUME Group Architects, Inc. of any dimensional HEATING - OCCUPIED SETPOINT °F 70 -- -- EWT ENTERING WATER VEL VELOCITY TS TEMPERATURE SENSOR errors, omissions or discrepancies before HEATING - UNOCCUPIED SETPOINT °F 60 -- -- TEMPERATURE VFD VARIABLE FREQUENCY beginning or fabricating any work. Do not scale these drawings. PROGRAMMED CONTROL FEATURES FCU FAN COIL UNIT DRIVE CO CARBON MONOXIDE SENSOR HVAC SYSTEM OCCUPIED/UNOCCUPIED MODE - PROGRAMMABLE THERMOSTAT Y DIV 23 DIV 23 W FFA FROM FLOOR ABOVE VRF VARIABLE REFRIGERANT COPYRIGHT Aria Group Architects, Inc. shall retain all REMOTE TEMPERATURE SENSOR Y DIV 23 DIV 23 X FFB FROM FLOOR BELOW FLOW CO2 CARBON DIOXIDE SENSOR FF FINISHED FLOOR VRV VARIABLE REFRIGERANT common law, statutory and other reserved DEMAND CONTROL VENTILATION - CO2 SENSOR FEEDBACK PPM N DIV 23 DIV 23 Z SPLIT DUCTLESS SYSTEM UNIT SCHEDULE rights. These drawings and related FPI FINS PER INCH VOLUME DP DIFFERENTIAL PRESSURE SENSOR documents shall not be duplicated, disclosed EQUIPMENT ACCESSORIES AND CONTROL MODULES MARK SERVICE MANUFACTURER MODEL REFR EVAPORATOR SECTION CONDENSING SECTION MINIMUM NOTES FPM FEET PER MINUTE W/ WITH or otherwise without written consent of Aria OUTSIDE AIR DAMPER - MOTOR OPERATED (MODULATING) Y FACTORY FACTORY K LOCATION TYPE CFM TC EAT V/PH MCA / MOCP FLA AMB V/PH MCA / MOCP EFFICIENCY GC GENERAL CONTRACTOR W/O WITHOUT FS FLOW SWITCH Group Architects, Inc. INTEGRATED ECONOMIZER - DIFFERENTIAL ENTHALPY ENABLE (OA ENTHALPY < RA ENTHALPY) Y FACTORY FACTORY E (MBH) (DB/WB) (°F) (SEER) GPM GALLONS PER MINUTE WB WET BULB HOA HAND -OFF -AUTOMATIC WC WATER COLUMN ECONOMIZER FAULT DETECTION AND DIAGNOSTICS (FDD) SYSTEM Y FACTORY FACTORY F, G FC-1/CU-1 AV/COMP MITSUBISHI PKA-A36KA7 / PUY-A36NKA7 R-410A 920 36.0 75.0 / 62.5 208/1 1 / 15 0.57 100 208/1 25 / 30 18.8 A,B,C,D,E,F HS HUMIDITY SENSOR HP HORSEPOWER WPD WATER PRESSURE DROP RELIEF - BAROMETRIC DAMPER Y FACTORY FACTORY HTG HEATING XP EXPLOSION PROOF PS PULL STATION COOLING COIL (DX - VARIABLE SPEED) Y FACTORY FACTORY M MODEL NUMBERS SHALL NOT BE CONSIDERED COMPLETE AND MATERIAL SHALL NOT BE ORDERED BY MANUFACTURER AND MODEL NUMBERS ONLY. REVIEW THE COMPLETE HEATING COIL (NATURAL GAS) Y FACTORY FACTORY M DESCRIPTION, NOTES AND SPECIFICATIONS TO DETERMINE THE EXACT MATERIAL AND ACCESSORIES TO BE ORDERED. THE MANUFACTURERS LISTED ARE THE BASIS FOR THE SUPPLY FAN CONTROL METHODS DESIGN. ON DURING OCCUPIED HOURS Y -- -- CYCLE WITH LOADS DURING UNOCCUPIED HOURS Y -- -- NOTES: VARIABLE VOLUME - STAGED FAN CONTROL IN RESPONSE TO ACTIVE COOLING COIL STAGES Y -- -- M, Q SAFETIES, INTERLOCKS, AND ALARMS A. CONTRACTOR SHALL VERIFY WITH EQUIPMENT SUPPLIER EXACT ROUTING AND SIZE OF INSULATED REFRIGERANT PIPING. INSTALL PER MANUFACTURERS RECOMMENDATIONS. GAS VALVE SAFETY Y FACTORY FACTORY F B. COORDINATE WITH THE MANUFACTURER THE HORIZONTAL AND VERTICAL REFRIGERANT PIPE ROUTING TO DETERMINE PIPE SIZES FOR THE REFRIGERANT PIPING. 2 07/26/19 ADD. #1 RETURN AIR SMOKE DETECTOR - SAFETY SHUTDOWN Y DIV 28 DIV 28 B MANUFACTURER SHALL PROVIDE DETAILED REFRIGERANT PIPING DIAGRAMS INCLUDING DIMENSIONAL DATA FOR ALL REFRIGERANT PIPING DEVICES. THE MANUFACTURER SHALL SIZE AND LOCATE THE ASSOCIATED REFRIGERANT TRAPS BASED ON THE ACTUAL ROUTING AND PROVIDE OTHER APPURTENANCES TO PROVIDE A FULLY FUNCTIONAL AND 1 06/17/19 ISSUE FOR LOW LIMIT FREEZESTAT - FREEZE PROTECTION SAFETY SHUTDOWN Y FACTORY FACTORY F OPERATIONAL SYSTEM. COORDINATE WITH THE MANUFACTURER LOCATIONS FOR ALL REFRIGERANT PIPING DEVICES TO MAINTAIN SERVICEABILITY AND ACCESSIBILITY. FIRE ALARM CONTROL PANEL - SAFETY SHUTDOWN INTERLOCK Y DIV 28 DIV 28 J PERMIT C. DIVISION 26 CONTRACTOR TO PROVIDE DISCONNECT SWITCH FOR EVAPORATOR SECTION AND CONDENSING SECTION. KITCHEN EXHAUST SYSTEM INTERLOCK Y DIV 23/26 DIV 23/26 S 0 06/06/19 90% D. PROVIDE WITH WALL MOUNTED THERMOSTAT BY UNIT MANUFACTURER. E. INDOOR AND OUTDOOR UNITS POWERED THROUGH SINGLE POINT CIRCUIT. REVIEW CONTROL PANEL(S), WIRING, THERMOSTAT(S), TEMPERATURE SENSOR(S),HUMIDISTAT(S), AND/OR CO2 SENSOR(S) WHERE SHOWN ON THE DRAWINGS AND AS F. PROVIDE WITH WIND BAFFLE ACCESSORY (WB-PA2) FOR OPERATION DOWN TO 0°F. NO. DATE REMARKS REQUIRED TO FACILITATE THE SCHEDULED CONTROL MODULES AND SEQUENCES OF OPERATION SHALL BE FURNISHED AND INSTALLED PER ROOFTOP UNIT CONTROL MATRIX. EACH UNIT SHALL CONTROL BASED ON ITS OWN INTERNAL SAFETIES, TIME DELAYS, AND SEQUENCES UNLESS NOTED OTHERWISE. COORDINATE REVISIONS WITH OWNER FINAL BUILDING AND EQUIPMENT SCHEDULES DURING STARTUP. REFERENCE DIVISION SPECIFICATIONS FOR INDIVIDUAL DEVICE REQUIREMENTS.

NOTES: B. DIVISION 28 CONTRACTOR SHALL PROVIDE DEVICE. REFERENCE FIRE PROTECTION FLOOR PLAN FOR SMOKE DECTECTOR REQUIREMENTS. E. IF SETPOINT VALUE IS LISTED, IT INDICATES ECONOMIZER HIGH-LIMIT SHUTOFF. UNIT SHALL BE IN ECONOMIZER IF CONDITIONS ARE LESS THAN SETPOINT. ROOFTOP UNIT SCHEDULE (DX COOLING, NATURAL GAS HEAT) (NO SUBSTITUTIONS) THE FOLLOWING SENSORS SHALL DETERMINE ECONOMIZER ON POINT. MARK SERVICE MANUFACTURER MODEL NOMINAL SUPPLY FAN COOLING COIL HEAT EXCHANGER MIN ELECTRICAL WEIGHT NOTES OUTSIDE AIR TEMPERATURE; DIVISION 23 PROVIDED AS PART OF ECONOMIZER CONTROL MODULE. LOCATION TONNAGE CFM ESP NOM TH SH EAT LAT REFR MIN EFF MIN NO MIN OUT NOM INPUT EAT LAT MIN NO O/A V/PH MCA MOCP DISC (LBS) RETURN AIR TEMPERATURE; DIVISION 23 PROVIDED AS PART OF ECONOMIZER CONTROL MODULE. (IN) HP (MBH) (MBH) (°F DB) (°F WB) (°F DB) (°F WB) TYPE (EER) (IEER) STAGES (MBH) (MBH) (°F DB) (°F DB) STAGES CFM TYPE OUTSIDE AIR HUMIDITY; DIVISION 23 PROVIDED AS PART OF ECONOMIZER CONTROL MODULE. RTU-13 RESTROOMS LENNOX LGH036H4E 3 1,100 0.75 0.5 14.3 14.3 75.1 65.3 54.7 54.6 R-410A 12.5 17.0 (SEER) 2 23.8 65.0 70.0 113.6 1 0 480/3 12 15 NON-FUSED 800 A - P RETURN AIR HUMIDITY; DIVISION 23 PROVIDED AS PART OF ECONOMIZER CONTROL MODULE. F. DEVICE SHALL BE FACTORY MOUNTED AND PRE-WIRED FOR OPERATION SUBJECT TO THE ONBOARD CONTROLLER. MODEL NUMBERS SHALL NOT BE CONSIDERED COMPLETE AND MATERIAL SHALL NOT BE ORDERED BY MANUFACTURER AND MODEL NUMBERS ONLY. REVIEW THE COMPLETE DESCRIPTION, NOTES AND SPECIFICATIONS TO DETERMINE THE EXACT MATERIAL AND ACCESSORIES TO BE ORDERED. G. PROVIDE UNIT WITH AN FDD SYSTEM CONSISTING OF PERMANENTLY INSTALLED OUTSIDE AIR, SUPPLY AIR, AND RETURN AIR TEMPERATURE SENSORS. THE UNIT CONTROLLER SHALL AT A MINIMUM BE CAPABLE OF PROVIDING SYSTEM STATUS OF ECONOMIZER, COMPRESSOR, HEATING, MIXED AIR LOW LIMIT ALARM, AND SENSOR VALUES. EACH OPERATING MODE SHALL BE CAPABLE OF INDEPENDENTLY OPERATING FOR TESTING. THE SYSTEM SHALL REPORT FAULTS TO NOTES: AN APPLICATION ACCESSIBLE BY SERVICE PERSONNEL. THE FOLLOWING FAULTS SHALL BE DETECTED: AIR TEMPERATURE SENSOR FAILURE, ECONOMIZER Drawing Title ENABLED/DISABLED WHEN ECONOMIZER SHOULD BE OFF/ON, RESPECTIVELY, DAMPER NOT MODULATING, AND EXCESS OUTSIDE AIR. A. J. DIVISION 28 TO INTERLOCK RTU SUPPLY FAN WITH FACP FOR SHUTDOWN UPON ACTIVATION OF ANSUL SYSTEM, SMOKE DETECTORS, PULL STATIONS, ETC. REFER TO ROOFTOP UNIT CONTROL MATRIX ON M3.2 FOR CONTROL FEATURES, MODULES, AND ACCESSORIES THAT SHALL BE PROVIDED WITH THE EQUIPMENT. MECHANICAL B. PER SEQUENCE OF OPERATION ON FA1.0. EQUIPMENT SIZED FOR 95°F AMBIENT TEMPERATURE. C. K. DETERMINE MINIMUM DAMPER POSITION IN FIELD DURING BALANCING TO PROVIDE SCHEDULED OUTDOOR AIRFLOW DURING OCCUPIED HOURS. DAMPER PROVIDE 2 INCH MERV 8, EFFICIENT PLEATED THROWAWAY AIR FILTERS. EP EP v19_justinfox_20190726160941.rvt SCHEDULES & D. SHALL BE CLOSED DURING UNOCCUPIED HOURS. PROVIDE FACTORY MOUNTED DISCONNECT INSTALLED ON SERVICE SIDE OF UNIT. E. M. UNITARY CONTROLLER SHALL MODULATE AND/OR CYCLE SUPPLY FAN SPEED SETTING AND COIL CAPACITY STAGES SUBJECT TO THE INTERNAL SAFETIES STARTERS FOR ALL MOTORS SHALL BE FURNISHED INTEGRAL WITH UNIT. LEGENDS F. AND SEQUENCES TO MAINTAIN SCHEDULED SETPOINTS. COORDINATE SIZE OF CONDUCTOR TERMINATION LUGS WITH CONDUCTOR SIZES SHOWN ON ELECTRICAL DRAWINGS. G. Q. PROVIDE STAGED FAN CONTROL WITH MINIMUM 2 FAN SPEEDS. LOW SPEED SHALL NOT EXCEED 66% OF FULL SPEED AND SHALL DRAW NO MORE THAN 40% PROVIDE 125 VAC, 20 AMP DUPLEX CONVENIENCE RECEPTACLE MOUNTED TO UNIT READY FOR FIELD WIRING WITH A COVER UL LISTED FOR WET AND DAMPER LOCATIONS WHEN IN USE. H. Job No. Drawn OF FAN POWER AT FULL SPEED. SPECIFIED FAN ESP ACCOUNTS FOR DUCT LOSSES EXTERNAL TO UNIT. J. S. INTERLOCK RTU SUPPLY FAN WITH KITCHEN EXHAUST FAN TO ENERGIZE WHEN HOOD SYSTEM IS ENERGIZED FOR PRESSURIZATION. PROVIDE STANDARD INSULATED ROOF CURB WITH MINIMUM HEIGHT OF 18 INCHES. PROVIDE SLOPED CURB IF NEEDED TO MATCH ROOF SLOPE. 184150 Author K. W. DIVISION 23 SHALL PROVIDE PROGRAMMABLE HONEYWELL VISIONPRO MODEL 8000 WITH WIFI THERMOSTAT (NOT INCLUDING REDLINK) (MODEL# TH8321WF). SCHEDULED WEIGHT IS THE MAXIMUM ALLOWABLE OPERATING WEIGHT OF THE EQUIPMENT AND CURB. L. PROVIDE 18 GAUGE LOW VOLTAGE WIRING PER MANUFACTURER'S RECOMMENDATIONS. PROVIDE GUARDS TO PROTECT CONDENSER COIL FROM HAIL OR OTHER DAMAGE. M. Scale Date X. DIVISION 23 SHALL PROVIDE REMOTE TEMPERATURE SENSOR (HONEYWELL TR21 WITH BLANK FACE). PROVIDE 18 GAUGE TWISTED PAIR, SHIELDED LOW PROVIDE HEATER TO MEET OR EXCEED SCHEDULED MINIMUM MBH OUTPUT. NOMINAL INPUT IS BASED ON LISTED MANUFACTURER'S STANDARD PRODUCT. COORDINATE EQUIPMENT GAS LOAD WITH PLUMBING CONTRACTOR IF DIFFERENT FROM THAT SCHEDULED. VOLTAGE WIRING PER MANUFACTURER'S RECOMMENDATION. MEET MINIMUM EFFICIENCY SCHEDULED. 12" = 1'-0" 06/06/2019 N. Z. DIVISION 23 SHALL PROVIDE LENNOX WALL MOUNTED CO2 SENSOR. PROVIDE PROVIDE 18 GAUGE SHIELDED TWISTED PAIR LOW VOLTAGE WIRING PER PROVIDE FACTORY START-UP OF UNITS AND BALANCE UNITS AFTER DUCTWORK IS INSTALLED. P. MANUFACTURER'S RECOMMENDATIONS. COORDINATE WITH MANUFACTURER TO PROVIDE A TAG FROM THE FACTORY TO MATCH THE “MARK” COLUMN OF THIS SCHEDULE. FOR EXAMPLE, EACH RTU SHALL READ THE RTU-# ON THE FACTORY TAGS TO FACILITATE COORDINATION ONSITE. NOTE: Sheet No. EXISTING CONDITIONS WERE TAKEN FROM ORIGINAL DRAWINGS & SITE VISITS AND MAY NOT REFLECT EXACT "AS -BUILT" CONDITIONS. FIELD VERIFY ALL EXISTING CONDITIONS PRIOR TO SUBMITTING FINAL BIDS. CAREFULLY COORDINATE NEW WORK AND DEMOLITION M3.2 WITH ALL OTHER DISCIPLINES AND EXISTING CONDITIONS. C:\Revit\Projects\1950001061 D&B LeHigh Valley PAM Valley LeHigh D&B C:\Revit\Projects\1950001061 SEAN O. EISLER O. SEAN G R O U P

830 North Blvd. Oak Park, Illinois 60301 708-445-8400 ariainc.com

ARIA GROUP ARCHITECTS, INC. WHITEHALL, 18052 PA

1471 MACARTHUR ROAD ROAD MACARTHUR 1471

FIELD VERIFICATION Contractor shall verify all figured dimensions and conditions at the job site and notify Aria Group Architects, Inc. of any dimensional errors, omissions or discrepancies before beginning or fabricating any work. Do not scale these drawings. COPYRIGHT Aria Group Architects, Inc. shall retain all common law, statutory and other reserved rights. These drawings and related documents shall not be duplicated, disclosed or otherwise without written consent of Aria Group Architects, Inc.

2 07/26/19 ADD. #1 1 06/17/19 ISSUE FOR PERMIT 0 06/06/19 90% REVIEW NO. DATE REMARKS REVISIONS

ISSUED FOR REFERENCE ONLY

Drawing Title

GREASE MASTER EP EP v19_justinfox_20190726160941.rvt SHEETS

Job No. Drawn 184150 Author

Scale Date 12" = 1'-0" 06/06/2019

830 North Blvd. Oak Park, Illinois 60301 708-445-8400 ariainc.com

ARIA GROUP ARCHITECTS, INC. WHITEHALL, 18052 PA

1471 MACARTHUR ROAD ROAD MACARTHUR 1471

2 07/26/19 ADD. #1 1 06/17/19 ISSUE FOR PERMIT 0 06/06/19 90% REVIEW NO. DATE REMARKS REVISIONS

ISSUED FOR REFERENCE ONLY

Drawing Title

GREASE MASTER EP EP v19_justinfox_20190726160941.rvt SHEETS

Job No. Drawn 184150 Author

Scale Date 12" = 1'-0" 06/06/2019

830 North Blvd. Oak Park, Illinois 60301 708-445-8400 ariainc.com

ARIA GROUP ARCHITECTS, INC. WHITEHALL, 18052 PA

1471 MACARTHUR ROAD ROAD MACARTHUR 1471

2 07/26/19 ADD. #1 1 06/17/19 ISSUE FOR PERMIT 0 06/06/19 90% REVIEW NO. DATE REMARKS REVISIONS

ISSUED FOR REFERENCE ONLY

Drawing Title

GREASE MASTER EP EP v19_justinfox_20190726160941.rvt SHEETS

Job No. Drawn 184150 Author

Scale Date 12" = 1'-0" 06/06/2019

830 North Blvd. Oak Park, Illinois 60301 708-445-8400 ariainc.com

ARIA GROUP ARCHITECTS, INC. WHITEHALL, 18052 PA

1471 MACARTHUR ROAD ROAD MACARTHUR 1471

2 07/26/19 ADD. #1 1 06/17/19 ISSUE FOR PERMIT 0 06/06/19 90% REVIEW NO. DATE REMARKS REVISIONS

ISSUED FOR REFERENCE ONLY

Drawing Title

GREASE MASTER EP EP v19_justinfox_20190726160941.rvt SHEETS

Job No. Drawn 184150 Author

Scale Date 12" = 1'-0" 06/06/2019

830 North Blvd. Oak Park, Illinois 60301 708-445-8400 ariainc.com

ARIA GROUP ARCHITECTS, INC. WHITEHALL, 18052 PA

1471 MACARTHUR ROAD ROAD MACARTHUR 1471

2 07/26/19 ADD. #1 1 06/17/19 ISSUE FOR PERMIT 0 06/06/19 90% REVIEW NO. DATE REMARKS REVISIONS

ISSUED FOR REFERENCE ONLY

Drawing Title

GREASE MASTER EP EP v19_justinfox_20190726160941.rvt SHEETS

Job No. Drawn 184150 Author

Scale Date 12" = 1'-0" 06/06/2019

830 North Blvd. Oak Park, Illinois 60301 708-445-8400 ariainc.com

ARIA GROUP ARCHITECTS, INC. WHITEHALL, 18052 PA

1471 MACARTHUR ROAD ROAD MACARTHUR 1471

2 07/26/19 ADD. #1 1 06/17/19 ISSUE FOR PERMIT 0 06/06/19 90% REVIEW NO. DATE REMARKS REVISIONS

ISSUED FOR REFERENCE ONLY

Drawing Title

GREASE MASTER EP EP v19_justinfox_20190726160941.rvt SHEETS

Job No. Drawn 184150 Author

Scale Date 12" = 1'-0" 06/06/2019

830 North Blvd. Oak Park, Illinois 60301 708-445-8400 ariainc.com

ARIA GROUP ARCHITECTS, INC. WHITEHALL, 18052 PA

1471 MACARTHUR ROAD ROAD MACARTHUR 1471

2 07/26/19 ADD. #1 1 06/17/19 ISSUE FOR PERMIT 0 06/06/19 90% REVIEW NO. DATE REMARKS REVISIONS

ISSUED FOR REFERENCE ONLY

Drawing Title

GREASE MASTER EP EP v19_justinfox_20190726160941.rvt SHEETS

Job No. Drawn 184150 Author

Scale Date 12" = 1'-0" 06/06/2019

830 North Blvd. Oak Park, Illinois 60301 708-445-8400 ariainc.com

ARIA GROUP ARCHITECTS, INC. WHITEHALL, 18052 PA

1471 MACARTHUR ROAD ROAD MACARTHUR 1471

2 07/26/19 ADD. #1 1 06/17/19 ISSUE FOR PERMIT 0 06/06/19 90% REVIEW NO. DATE REMARKS REVISIONS

ISSUED FOR REFERENCE ONLY

Drawing Title

GREASE MASTER EP EP v19_justinfox_20190726160941.rvt SHEETS

Job No. Drawn 184150 Author

Scale Date 12" = 1'-0" 06/06/2019

830 North Blvd. Oak Park, Illinois 60301 708-445-8400 ariainc.com

ARIA GROUP ARCHITECTS, INC. WHITEHALL, 18052 PA

1471 MACARTHUR ROAD ROAD MACARTHUR 1471

2 07/26/19 ADD. #1 1 06/17/19 ISSUE FOR PERMIT 0 06/06/19 90% REVIEW NO. DATE REMARKS REVISIONS

ISSUED FOR REFERENCE ONLY

Drawing Title

GREASE MASTER EP EP v19_justinfox_20190726160941.rvt SHEETS

Job No. Drawn 184150 Author

Scale Date 12" = 1'-0" 06/06/2019

830 North Blvd. Oak Park, Illinois 60301 708-445-8400 ariainc.com

ARIA GROUP ARCHITECTS, INC. WHITEHALL, 18052 PA

1471 MACARTHUR ROAD ROAD MACARTHUR 1471

2 07/26/19 ADD. #1 1 06/17/19 ISSUE FOR PERMIT 0 06/06/19 90% REVIEW NO. DATE REMARKS REVISIONS

ISSUED FOR REFERENCE ONLY

Drawing Title

GREASE MASTER EP EP v19_justinfox_20190726160941.rvt SHEETS

Job No. Drawn 184150 Author

Scale Date 12" = 1'-0" 06/06/2019

830 North Blvd. Oak Park, Illinois 60301 708-445-8400 ariainc.com

ARIA GROUP ARCHITECTS, INC. WHITEHALL, 18052 PA

1471 MACARTHUR ROAD ROAD MACARTHUR 1471

2 07/26/19 ADD. #1 1 06/17/19 ISSUE FOR PERMIT 0 06/06/19 90% REVIEW NO. DATE REMARKS REVISIONS

ISSUED FOR REFERENCE ONLY

Drawing Title

GREASE MASTER EP EP v19_justinfox_20190726160941.rvt SHEETS

Job No. Drawn 184150 Author

Scale Date 12" = 1'-0" 06/06/2019

830 North Blvd. Oak Park, Illinois 60301 708-445-8400 ariainc.com

ARIA GROUP ARCHITECTS, INC. WHITEHALL, 18052 PA

1471 MACARTHUR ROAD ROAD MACARTHUR 1471

2 07/26/19 ADD. #1 1 06/17/19 ISSUE FOR PERMIT 0 06/06/19 90% REVIEW NO. DATE REMARKS REVISIONS

ISSUED FOR REFERENCE ONLY

Drawing Title

GREASE MASTER EP EP v19_justinfox_20190726160941.rvt SHEETS

Job No. Drawn 184150 Author

Scale Date 12" = 1'-0" 06/06/2019

830 North Blvd. Oak Park, Illinois 60301 708-445-8400 ariainc.com

ARIA GROUP ARCHITECTS, INC. WHITEHALL, 18052 PA

1471 MACARTHUR ROAD ROAD MACARTHUR 1471

2 07/26/19 ADD. #1 1 06/17/19 ISSUE FOR PERMIT 0 06/06/19 90% REVIEW NO. DATE REMARKS REVISIONS

ISSUED FOR REFERENCE ONLY

Drawing Title

GREASE MASTER EP EP v19_justinfox_20190726160941.rvt SHEETS

Job No. Drawn 184150 Author

Scale Date 12" = 1'-0" 06/06/2019

830 North Blvd. Oak Park, Illinois 60301 708-445-8400 ariainc.com

ARIA GROUP ARCHITECTS, INC. WHITEHALL, 18052 PA

1471 MACARTHUR ROAD ROAD MACARTHUR 1471

2 07/26/19 ADD. #1 1 06/17/19 ISSUE FOR PERMIT 0 06/06/19 90% REVIEW NO. DATE REMARKS REVISIONS

ISSUED FOR REFERENCE ONLY

Drawing Title

GREASE MASTER EP EP v19_justinfox_20190726160941.rvt SHEETS

Job No. Drawn 184150 Author

Scale Date 12" = 1'-0" 06/06/2019

NOTE: Sheet No. EXISTING CONDITIONS WERE TAKEN FROM ORIGINAL DRAWINGS & SITE VISITS AND MAY NOT REFLECT EXACT "AS -BUILT" CONDITIONS. FIELD VERIFY ALL EXISTING CONDITIONS PRIOR TO SUBMITTING FINAL BIDS. CAREFULLY COORDINATE NEW WORK AND DEMOLITION M4.14 WITH ALL OTHER DISCIPLINES AND EXISTING CONDITIONS. C:\Revit\Projects\1950001061 D&B LeHigh Valley PAM Valley LeHigh D&B C:\Revit\Projects\1950001061 ALL MECHANICAL EQUIPMENT CONTROL WIRING INSTALLED ON ROOF SHALL BE INSTALLED IN CONDUIT PER DIVISION 26 G R O U P SPECIFICAIONS. 830 North Blvd. PAINT EXTERIOR EXPOSED GAS PIPING WITH Oak Park, CORROSION RESISTANT PAINT. COLOR AS Illinois SELECTED BY ARCHITECT WHERE VISIBLE 60301 TO PUBLIC. 708-445-8400 MECHANICAL/PLUMBING GENERAL NOTES: ariainc.com 1. ALL VENT STACKS SHALL BE NO LESS THAN 12 ’-0” FROM PARAPET, AT LEAST 10 FEET FROM OUTSIDE AIR ARIA GROUP ARCHITECTS, INC. INTAKES, AND ABOVE ROOF SURFACE 6 ” MINIMUM TO FULL HEIGHT OF PARAPET, WHICHEVER IS GREATER. CONTRACTOR SHALL PROVIDE BRACING AS SPECIFIED.

2. COORDINATE EXACT EQUIPMENT LOCATIONS WITH .2A OTHER TRADES PRIOR TO INSTALLATION.

3. ALL VENT STACKS SHALL BE NO LESS THAN 12' -0" FROM PARAPET, AT LEAST 10 FEET FROM OUTSIDE AIR INTAKES, AND ABOVE ROOF SURFACE 6" MINIMUM TO

FULL HEIGHT OF PARAPET, WHICHEVER IS GREATER. FAX CONTRACTOR SHALL PROVIDE BRACING AS SPECIFIED. 1950001061

A LENEXA, KS 66214 # MECHANICAL/PLUMBING PLAN NOTES: 913.742.5000 913.742.5001

1 LANDLORD TO INSTALL OWNER FURNISHED MAKE-UP LENEXA DRIVE,8345 SUITE 300 TEL AIR UNIT CURB. CONTRACTOR SHALL INSTALL OWNER WWW.HENDERSONENGINEERS.COM FURNISHED MAKE-UP AIR UNIT. 2 INSTALL ROOFTOP UNIT CONDENSATE DRAIN WITH P-TRAP. EXTEND DRAIN LINE TO NEAREST ROOF DRAIN AND TERMINATE WITH AIR GAP. 3 REFRIGERATION CONDENSER PROVIDED BY KITCHEN EQUIPMENT CONTRACTOR. COORDINATE EQUIPMENT

ETR RTU -12 LOCATION AND CONDENSER INSTALLATION WITH WHITEHALL, 18052 PA (LANDLORD KITCHEN EQUIPMENT CONTRACTOR. REFER TO PROVIDED) EQUIPMENT SCHEDULE ON KITCHEN DRAWINGS FOR ADDITIONAL INFORMATION. ROOF PLATFORM PROVIDED ETR RTU -2 BY LANDLORD. (LANDLORD 4 THE ROOF AREA AROUND GREASE EXHAUST PROVIDED) EQUIPMENT SHALL BE PROTECTED WITH A GREASE-GUARD, GREASE GUARDS ARE OWNER FURNISHED, CONTRACTOR INSTALLED. ETR RTU -9 (LANDLORD 5 LANDLORD TO PROVIDE ROOF PENETRATION AND PROVIDED) INSTALL OWNER FURNISHED ROOF JACK. 6 LANDLORD TO INSTALL OWNER FURNISHED FAN CURB. B 1" CD (ETR) 3/4" MPG (ETR) CONTRACTOR SHALL INSTALL OWNER FURNISHED 3/4" MPG (ETR) EXHAUST FAN. 1" CD (ETR) 7 LANDLORD TO INSTALL OWNER FURNISHED ROOF HOOD 1" CD (ETR) CURB. CONTRACTOR SHALL INSTALL OWNER FURNISHED HOOD.

ETR RTU -11 ETR RTU -1 (LANDLORD 3/4" MPG (ETR) 3/4" (LANDLORD PROVIDED) PROVIDED)

1" CD (ETR) CD 1" 1" MPG 1" (ETR) 1" CD (ETR) CD 1"

C MPG (ETR) 3/4" 3/4" MPG (ETR) 3/4" MPG (ETR) 1" CD (ETR) 1" CD (ETR) 1" CD (ETR) CD 1" 1 1/4" MPG (ETR) 1/4" 1 ETR RTU -3 (LANDLORD 3/4" MPG (ETR) 1" CD (ETR) PROVIDED) ETR RTU -10 (LANDLORD PROVIDED) 3 1" MPG 1" (ETR) 1" CD (ETR) CD 1"

1" CD (ETR) CD 1" FSEC REFRIGERATION RACK RH 7 RH 4

1 1/4" MPG (ETR) 1/4" 1 1 7 ETR RTU -4 2 M2.1 (LANDLORD PROVIDED) (TYP) D 1" CD (ETR) KEF 6 3/4" MPG (ETR) ROOF JACK 6 3/4" MPG (ETR) 1471 MACARTHUR ROAD ROAD MACARTHUR 1471 8 5 M2.1 3 400 CFH ROOF JACK 1 1/4" MPG (ETR) MAU GPR1 FIELD VERIFICATION 1" CD (ETR) 2 3/4" MPG RH Contractor shall verify all figured dimensions 3 (ETR) and conditions at the job site and notify Aria 1 2 1" CD Group Architects, Inc. of any dimensional errors, omissions or discrepancies before 1 1/4" CD (ETR) CD (ETR) 1/4" 1 175 CFH CD (ETR) 1/4" 1 beginning or fabricating any work. Do not scale 6 ICE MACHINE MPG (ETR) 1/4" 1 CONDENSER MAU these drawings. P4.3 GPR1 1 2 5 (TYP 2) 1 COPYRIGHT (TYP) 1" CD (ETR) Aria Group Architects, Inc. shall retain all common law, statutory and other reserved 1 1/4" MPG (ETR) 1 1/4" MPG (ETR) 7 1" MPG (ETR) rights. These drawings and related ETR RTU -6 3/4" MPG (ETR) 3/4" MPG (ETR) documents shall not be duplicated, disclosed P4.3 1 1/2" MPG (ETR) (LANDLORD 3/4" MPG (ETR) or otherwise without written consent of Aria 1" CD (ETR) PROVIDED) Group Architects, Inc. (TYP) 3/4" MPG (ETR) 1" MPG (ETR) 3/4" MPG (ETR) 1" CD KEF KEF 3/4" MPG 3/4" MPG (ETR) 6 4 6 4 4 3 4"VTR RTU 10 KEF (ETR) 1" CD (ETR) 1" CD (ETR) 65 CFH 6 4 13 EF 9 M2.1 5 1" CD (ETR) 6 2 M2.1 10 2 10 ETR RTU -7 ETR RTU -8 M2.1 (LANDLORD (LANDLORD MPG (ETR) 3/4" M2.1 PROVIDED) PROVIDED) CO E KEF 1" CD 6 4 GPR1 1 EF 9 3/4" MPG 6 1 KEF ETR RTU -5 M2.1 9 EF 10 6 4 6 2 (LANDLORD 2 07/26/19 ADD. #1 M2.1 3 M2.1 PROVIDE REFRIGERANT PIPING PROVIDED) 4"VTR CU FROM EXTERIOR CONDENSING 10 (ETR) 4"VTR 1 06/17/19 ISSUE FOR 1 UNIT TO INTERIOR EVAPORATOR (ETR) M2.1 CD (ETR) 1/4" 1 UNIT. SIZE AND ROUTE PIPING PERMIT 2" MPG 2" (ETR)

1 1/4" CD (ETR) 1/4" 1 PER MANUFACTURER'S 0 06/06/19 90% RECOMMENDATIONS. CD (ETR) 1/4" 1 REVIEW

LANDLORD PROVIDED CONCENTRIC FLUE/AIR INTAKE VENTS CD 1" NO. DATE REMARKS REVISIONS F DOWNSPOUT DOWNSPOUT DOWNSPOUT (ETR) (ETR) (ETR)

8 7 6 5 4 3 2 1

Drawing Title MECHANICAL &

EP EP v19_justinfox_20190726160941.rvt PLUMBING ROOF MECHANICAL & PLUMBING ROOF PLAN 1 N PLAN 1/8" = 1'-0"

Job No. Drawn 184150 Author

Scale Date 1/8" = 1'-0" 06/06/2019